Japan Radio Test Report: Attestation of Global Compliance (Shenzhen) Co., LTD

Page 1 of 68
Japan radio Test Report
Report No.: AGC00688180207TE01
PRODUCT DESIGNATION : 2.4G Wireless Mouse Receiver
BRAND NAME : SANWA SUPPLY
TEST MODEL : SANWA RC5
CLIENT : Sanwa Supply Inc.
DATE OF ISSUE : Mar. 28, 2018

Article 2 Paragraph 1 Item 19 of the Certification,
STANDARD(S) :
MIC Notice No.88 Appendix No.43
REPORT VERSION : V1.0
Attestation of Global Compliance (Shenzhen) Co., Ltd.
CAUTION:
This report shall not be reproduced except in full without the written permission of the test
laboratory and shall not be quoted out of context.
Page 2 of 68
TABALE OF CONTENTS
TABALE OF CONTENTS ..................................................................................................................................... 2

1. TEST RESULT CERTIFICATION ..................................................................................................................... 3
2. SANWA SUPPLY INFORMATION.................................................................................................................... 4
2.1 EUT DESCRIPTION ................................................................................................................................... 4
2.2 CHANNEL LIST........................................................................................................................................... 5
2.3 DESCRIPTION OF TEST MODES ............................................................................................................. 6
3. TEST ITEMS AND THE RESULTS .................................................................................................................. 7
4. DETAILS OF TEST ........................................................................................................................................... 8
4.1 IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION ........................................................... 8
4.2 LIST OF TEST EQUIPMENTS.................................................................................................................... 8
4.3 ENVIRONMENTAL CONDITIONS .............................................................................................................. 8
5. TEST RESULTS ................................................................................................................................................ 9
5.1 FREQUENCY ERROR MEASUREMENT .................................................................................................. 9
5.2. OCCUPIED BANDWIDTH AND SPREAD-SPECTRUM BANDWIDTH MEASUREMENT......................11
5.3. UNWANTED EMISSION INTENSITY MEASUREMENT ........................................................................ 22
5.4. ANTENNA POWER ERROR MEASUREMENT ...................................................................................... 48
5.5. IMITATION OF COLLATERAL EMISSION OF RECEIVER MEASUREMENT ....................................... 51
5.6. TRANSMISSION ANTENNA GAIN (EIRP ANTENNA POWER) MEASUREMENT ................................ 56
5.7. TRANSMISSION RADIATION ANGLE WIDTH (3DB BEAMWIDTH) MEASUREMENT ........................ 58
5.8. RADIO INTERFERENCE PREVENTION CAPABILITY MEASUREMENT ............................................. 60
5.9. CONSTRUCTION PROTECTION CONFIRMATION METHOD.............................................................. 62
APPENDIX A: PHOTOGRAPHS OF THE TEST SETUP .................................................................................. 63
APPENDIX B: PHOTOGRAPHS OF THE EUT ................................................................................................. 64
Page 3 of 68
1. TEST RESULT CERTIFICATION
Applicant Name Sanwa Supply Inc.
Address 1-10-1 Tamachi Okayama City 700-0825 Japan
Manufacturer Name Shenzhen Hangshi Technology Co., Ltd
1/F & 2/F, G-A2 BLDG, 3/F &4/F, G-A1 BLDG, Democracy West Industry Park, Shajing
Address
Town, Baoan District, Shenzhen, Guangzhou, P.R.China
Product Designation 2.4G Wireless Mouse Receiver
Brand Name SANWA SUPPLY
Test Model SANWA RC5

Article 2 Paragraph 1 Item 19 of the Certification,
Test Standard
MIC Notice No.88 Appendix No.43
File Number AGC00688180207TE01
Date of Test Mar. 21, 2018 to Mar. 28, 2018
Test Result Pass
We (AGC), Attestation of Global Compliance (Shenzhen) Co., Ltd. for compliance with the requirements set
forth in the Japan MIC Notice No.88 Annex43. The results of testing in this report apply to the product/system
which was tested only. Other similar equipment will not necessarily produce the same results due to production
tolerance and measurement uncertainties.
Tested by
Max Zhang(Zhang Yi) Mar. 28, 2018
Reviewed by
Bart Xie(Xie Xiaobin)

Mar. 28, 2018
Approved By
Forrest Lei(Lei Yonggang)
Authorized Officer Mar. 28, 2018
Page 4 of 68
2. SANWA SUPPLY INFORMATION

Note: the following data is based on the information by the applicant.
2.1 EUT DESCRIPTION
Product Designation 2.4G Wireless Mouse Receiver
Model Name SANWA RC5
Hardware Version N 20120722
Software Version V1.0
Modulation Type GFSK
Operation Frequency 2405~2470MHz
PCB Antenna:
Antenna Designation
Ant Gain: -1.66dBi
Channel No. 8 Channels
Rated Power Density 0.05mW
Power Supply DC 5.0V
(5.5V)High Voltage + 10% of Normal Voltage

Test Power (4.5V)Low Voltage - 10% of Normal Voltage
(5.0V) Normal Voltage
Test Channel 2405MHz, 2430MHz, 2470MHz
Note:
1. The EUT has only one antenna.
2. Only those frequencies within 2405-2470MHz were tested according the standard requirement.
3. The EUT has single chip with one antennas and the output of the antenna feeder is 50 Ohm.
4. The EUT is a 2.4GHz single-chip controller according to MIC Notice No.88 Annex43.
5. For more details, please refer to the User’s manual of the EUT.
Page 5 of 68
2.2 CHANNEL LIST
Frequency Band Channel Number Frequency

1 2405 MHZ
2 2413 MHZ
3 2422 MHZ
4 2430 MHZ
2400~2483.5MHZ
5 2440 MHZ
6 2450 MHZ
7 2460 MHZ
8 2470 MHZ
Note: Each product worked at one channel by pairing to avoid the interference.
Page 6 of 68
2.3 DESCRIPTION OF TEST MODES

The transmitter module was tested while in a continuous transmitter/receiver mode.
The EUT was tuned to a low, middle, and high channel for all tests. For all test case pre/scans were completed
in all
modes to determine worst case levels.
Power Supply Voltage Fluctuation Test

Voltage Fluctuation High Voltage +10% of Low Voltage -10% of
Normal Voltage
Test Normal Voltage Normal Voltage
battery power 5.0V 5.5V 4.5V
Voltage Variation
-- 10% 10%
(%)
Note:
Voltage Variation (%)
= (Output high or Low Voltage - Output Normal Voltage)/ Output Normal Voltage*100
During the input supply voltage to the EUT from the external power source is varied by +/- 10%, if output
voltage had been confirmed that the fluctuation of power supply to the RF circuit of EUT (excluding power
source) is equal to or less than +/-1%. Exempt extremely high and low supply voltage condition test, EUT only
operated in normal voltage to test all regulations.
Page 7 of 68
3. TEST ITEMS AND THE RESULTS
Part Rule Section Description of Test Result
5.1 3 Frequency Error Complies

Occupied Bandwidth (99%) and Spread-spectrum
5.2 4 Complies
Bandwidth (90%)
5.3 5 Unwanted Emission Intensity Complies
5.4 6 Antenna Power Error Complies
5.5 7 Limitation of Collateral Emission of Receiver Complies

Transmission Antenna Gain (EIRP Antenna
5.6 8 Complies
Power)
Transmission Radiation Angle Width (3dB
5.7 9 Complies
Beamwidth)
5.8 10 Radio Interference Prevention Capability Complies
5.9 Note1 Carrier Sense Capability N/A
5.10 Note 2 Construction Protection Confirmation Complies
Note 1: MIC Notice No.88 Appendix No.43

Note 2: MIC Ordinance Regulating Radio Equipment Section 4.17 of Article 49.20
Page 8 of 68
4. DETAILS OF TEST
4.1 IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION
Company Name: Attestation of Global Compliance (Shenzhen) Co., Ltd.
2/F., Building 2, No.1-No.4, Chaxi Sanwei Technical Industrial Park, Gushu,

Address:
Xixiang, Bao'an District, Shenzhen, Guangdong, China
Website www.agc-cert.com
4.2 LIST OF TEST EQUIPMENTS

Calibration Calibration
Description Manufacturer Model No. Serial No.
Date Due.
Regulated dc
LONGWEI 50V30A 978256 Jul.14, 2017 Jul.13, 2018
power supply
Exa signal analyzer AGILENT N9020A MY52090123 Sep.21, 2017 Sep.20, 2018
Power meter R&S NRVD 832378/027 Jul.14, 2017 Jul.13, 2018
Power sensor ANRITSU MA2491A 0341138 Jul.14, 2017 Jul.13, 2018
Pre-amplifier ANRITSU MH648A M09961 Jul.14, 2017 Jul.13, 2018
RF Cable SUIRONG 30MHZ-18GHZ N/A Jul.14, 2017 Jul.13, 2018
Attenuator MINI-CIRCUITS VAT-10+ 15542 Jul.14, 2017 Jul.13, 2018
2.4G Band Fliter MICRO RRANICS BRM50702 087 Jul.14, 2017 Jul.13, 2018
Calibration Company Name: South China National Centre Metrology & Guangdong Institute of Metrology
Calibration Person: Chen Sheng and Liu Wen Gang
4.3 ENVIRONMENTAL CONDITIONS

During the measurement the environmental conditions were within the listed ranges:
- Temperature: 15-35ºC
- Humidity: 45-85 %
- Atmospheric pressure: 86-106 kPa
Page 9 of 68
5. TEST RESULTS
5.1 FREQUENCY ERROR MEASUREMENT
5.1.1. LIMIT
Item Limits
Frequency Tolerance (2405~2470MHz) ≦50ppm
5.1.2. TEST PROCEDURES

1. Frequency accuracy of SA shall be less than 10% of limits tolerance (5ppm)
2. Setting of SA is following as: RB: 9kHz / VB:30kHz / SPAN: 1MHz /
AT: 10dB / Ref: 0dBm
3. Center Frequency: The center frequency of testing for EUT
4. Sweep time: Auto
5. Sweep mode: Continuous sweep
6. Detect mode: Positive peak
7. Mark function: Frequency Counter (Resolution 100Hz)
8. EUT have transmitted absence of modulation signal and fixed channelize. “f” is using the
mark cursor to mark the peak frequency value，”fc” is declaring of channel frequency.
Then the frequency error formula is (fc-f)/fc×106 ppm and the limit is less than ±50ppm
5.1.3. TEST SETUP LAYOUT
5.1.4. TEST DEVIATION
There is no deviation with the original standard.
5.1.5. EUT OPERATION DURING TEST
The EUT was placed on the test table and programmed in un-modulation function.
Page 10 of 68
5.1.6. RESULTS OF FREQUENCY ERROR
EUT： SANWA RC5 Test Date: Mar. 26, 2018
Temperature: 250C Tested by: Max

Humidity: 55 % RH Operation Mode: Un-modulation
Test Voltage: 5.0V

Test Measured
Frequency Limit
Frequency Frequency P/F
Error(ppm) (ppm)
(MHz) (MHz)
2405 2404.976 -9.98 ±50 PASS
Un-modulation 2430 2429.975 -10.29 ±50 PASS
2470 2469.974 -10.53 ±50 PASS
Test Voltage: 5.5V

Test Measured
Frequency Limit
Error(ppm) (ppm)
(MHz) (MHz)
2405 2404.973 -11.23 ±50 PASS
2470 2469.972 -11.34 ±50 PASS
Test Voltage: 4.5V
Test Measured
Frequency Limit
Error(ppm) (ppm)
(MHz) (MHz)
2405 2404.972 -11.64 ±50 PASS
2470 2469.972 -11.34 ±50 PASS

Page 11 of 68
5.2. OCCUPIED BANDWIDTH AND SPREAD-SPECTRUM BANDWIDTH MEASUREMENT

5.2.1. LIMIT
Item Limits
Occupied Band Width: FH 83.5MHz; OFDM,DS ≦26MHz;Others≦26MHz
Spreading Bandwidth: ≧500 kHz (FH, DS)
5.2.2. MEASURING INSTRUMENTS AND SETTING

1. Setting of SA is following as: RB: Auto / VB:Auto / AT: 30dB Ref:
20dBm / Sweep time: Auto / Sweep Mode: Continuous sweep / Detect mode: Positive
peak / Trace mode: Max hold
2 . EUT have transmitted the maximum modulation signal and fixed channelize ( For DSSS
or OFDM Device) or continuous maximum power of hopping mode(For FHSS Device).
SA set to 99% of occupied bandwidth to measure occupied bandwidth. The limit is less
than 26MHz(For DSSS or OFDM Device) or 83.5MHz(For FHSS Device).
3. SA set to 90% of occupied bandwidth to measure Spread Spectrum Bandwidth and
must greater than 500kHz.
4. Spread Spectrum Factor = Spread Spectrum Bandwidth / modulation rate of EUT.
5. Spread Spectrum Factor limit is greater than 5

The EUT was programmed to be in continuously transmitting mode.

Page 12 of 68
5.2.7. RESULTS OF OCCUPIED BANDWIDTH AND SPREAD-SPECTRUM BANDWIDTH

Humidity: 55 % RH Operation Mode: GFSK
Test Voltage: 5.5V

Test frequency Occupied Spread
Limit Limit
(MHz) Bandwidth Bandwidth P/F
(MHz) (KHz)
(MHz) (MHz)
2405 2.3605 <26 1.5780 >500 PASS
2430 2.3654 <26 1.5797 >500 PASS
2470 2.3582 <26 1.5746 >500 PASS
Test Voltage: 5.0V

Limit Limit
(MHz) (KHz)
(MHz) (MHz)
2405 2.3538 <26 1.5707 >500 PASS
2430 2.3601 <26 1.5608 >500 PASS
2470 2.3632 <26 1.5697 >500 PASS
Test Voltage: 4.5V

Limit Limit
(MHz) (KHz)
(MHz) (MHz)
2405 2.3745 <26 1.5771 >500 PASS
2430 2.3487 <26 1.5540 >500 PASS
2470 2.3702 <26 1.5807 >500 PASS

Page 13 of 68
High Voltage-Occupied Bandwidth (99%)-Low channel
High Voltage -Spread Bandwidth (90%)-Low channel

Page 14 of 68
High Voltage-Occupied Bandwidth (99%)-Middle channel
High Voltage -Spread Bandwidth (90%)-Middle channel

Page 15 of 68
High Voltage-Occupied Bandwidth (99%)-High channel
High Voltage -Spread Bandwidth (90%)-High Channel

Page 16 of 68
Normal Voltage-Occupied Bandwidth (99%)-Low channel
Normal Voltage-Spread Bandwidth (90%)-Low channel

Page 17 of 68
Normal Voltage-Occupied Bandwidth (99%)-Middle channel
Normal Voltage -Spread Bandwidth (90%)-Middle channel

Page 18 of 68
Normal Voltage -Occupied Bandwidth (99%)-High channel
Normal Voltage -Spread Bandwidth (90%)-High Channel

Page 19 of 68
Low Voltage-Occupied Bandwidth (99%)-Low channel
Low Voltage-Spread Bandwidth (90%)-Low channel

Page 20 of 68
Low Voltage-Occupied Bandwidth (99%)-Middle channel
Low Voltage -Spread Bandwidth (90%)-Middle channel

Page 21 of 68
Low Voltage -Occupied Bandwidth (99%)-High channel
Low Voltage -Spread Bandwidth (90%)-High Channel

Page 22 of 68
5.3. UNWANTED EMISSION INTENSITY MEASUREMENT

5.3.1 LIMIT
Item Limits
≦ 0.25 μW (f≦1000MHz)
≦ 2.5 μW (1000MHz<f≦2387MHz)
TX Spurious Emission(2403~2474MHz) ≦25 μW (2387MHz<f≦2400MHz)
≦25 μW (2483.5MHz≦f<2496.5MHz)
≦2.5 μW (2496.5MHz≦f<12500MHz)

Please refer to section 5 in this report. The following table is the setting of Spectrum Analyzer.
Spectrum Parameter Setting
Attenuation Auto
RBW/ VBW 1 MHz
Detector Peak
Trace Max Hold
Sweep Time Auto

Page 23 of 68

1. EUT have transmitted the maximum modulation signal and fixed channelize.
2. Setting of SA is following as: Below 1GHz RB:100KHz / VB:100KHz
Above 1GHz RB:1MHz / VB:1MHz / AT: 10dB Ref: 0dBm / Sweep time: Auto
Sweep Mode: Continuous sweep / Detect mode: Positive peak
Trace mode: Max hold
3. Setting of SA is following as 30MHz and stop frequency 1000MHz Then to mark
peak reading value + cable loss shall be less than 0.25μW.
4. Setting of SA is following as 1000MHz and stop frequency 2387MHz Then to mark
peak reading value + cable loss shall be less than 2.5μW.
5. SA adjusted to start frequency 2387MHz and stop frequency 2400MHz. Then to
mark peak reading value + cable loss shall be less than 25μW.
6. SA adjusted to start frequency 2483.5MHz and stop frequency 2496.5MHz Then to
mark peak reading value + cable loss shall be less than 25μW
7. SA adjusted to start frequency 2496.5MHz and stop frequency 12500MHz Then to
mark peak reading value + cable loss shall be less than 2.5μW
8. Measure side band spurious as follows: For 2.4GHz band: 2374MHz~2400MHz
and 2483.5MHz~2509.5MHz RBW = VBW = 30kHz, Result_Value = Meaured_
Value + 15.2 [dBm]
9. If the Result_Value is over the requirement, take total sum of 1MHz band centered
at the spur frequency like ACLP measurement as Result_Value.


Page 24 of 68
5.3.7. TEST RESULT OF UNWANTED EMISSION INTENSITY

Test Voltage High Voltage
Low Channel-Frequency Band 1 (30 MHz ≦ f ≦ 1000 MHz)

Page 25 of 68
Low Channel-Frequency Band 2 (1000 MHz < f ≦ 2387 MHz)

Page 26 of 68
Low Channel-Frequency Band 4 (2483.5 MHz ≦ f < 2496.5 MHz)
Low Channel-Frequency Band 5 (2496.5 MHz ≦ f < 12.5 GHz)

Page 27 of 68
Middle Channel-Frequency Band 1 (30 MHz ≦ f ≦ 1000 MHz)
Middle Channel--Frequency Band 2 (1000 MHz < f ≦ 2387 MHz)

Page 28 of 68
Middle Channel--Frequency Band 4 (2483.5 MHz ≦ f < 2496.5 MHz)

Page 29 of 68
Middle Channel--Frequency Band 5 (2496.5 MHz ≦ f < 12.5 GHz)
High Channel--Frequency Band 1 (30 MHz ≦ f ≦ 1000 MHz)

Page 30 of 68
High Channel--Frequency Band 2 (1000 MHz < f ≦ 2387 MHz)

Page 31 of 68
High Channel--Frequency Band 4 (2483.5 MHz ≦ f < 2496.5 MHz)
High Channel--Frequency Band 5 (2496.5 MHz ≦ f < 12.5 GHz)

Page 32 of 68

Test Voltage Normal Voltage

Page 33 of 68

Page 34 of 68

Page 35 of 68

Page 36 of 68

Page 37 of 68

Page 38 of 68

Page 39 of 68

Page 40 of 68

Test Voltage Low Voltage

Page 41 of 68

Page 42 of 68

Page 43 of 68

Page 44 of 68

Page 45 of 68

Page 46 of 68

Page 47 of 68

Page 48 of 68
5.4. ANTENNA POWER ERROR MEASUREMENT

5.4.1. LIMIT
Item Limits
≦3mW/MHz (FH form 2427 - 2474.75 MHz)

Antenna Power
≦10mW/MHz (OFDM,DS from2400~2483.5MHz)
Density
≦10mW/MHz(Other from 2400~2483.5MHz)
+20%, -80% (Base on manufacturer declare antenna power
Antenna Power Error
density)

Attenuation Auto
RBW / VBW 1 MHz
Detector Peak
Trace Max Hold
Sweep Time Auto

Page 49 of 68

1. A power meter is connected on the IF output port of the spectrum analyzer.
2. Adjust the spectrum analyzer to have the center frequency the same with the
measured carrier. RBW=VBW=1MHz, detector mode is positive peak. Turn
off the averaging function and use zero span.
3. The calibrating signal power shall be reduced to 0 dBm and it shall be verified
that the power meter reading also reduces by 10 dB.
4 . Connect the equipment to be measured. Using the following settings of the
spectrum analyzer in combination with "max hold" function, find the frequency
of highest power output in the power envelope: center frequency equal to
operating frequency; RBW & VBW: 1 MHz; detector mode: positive peak; averaging:
off; span: 3 times the spectrum width; amplitude: adjust for middle of the
instrument' range. The frequency found shall be recorded.
5 . Set the center frequency of the spectrum analyzer to the found frequency and switch
to zero span. The power meter indicates the measured power density “E”.
6. Remove the EUT and put the replacing standard signal generator (SSG). Set
the standard signal generator (SSG) at same frequency and transmit on, then set
SSG output power at Pt to give the equivalent output level of “E”.
7. Calculate antenna power density by the formula below PD = Pt + 10*log(1/x).
x: The duty cycle of the EUT in continuously transmitting mode
Pt: Output power of the SSG
8. Antenna Power Error is definition that actual measure antenna power tolerance
between + 20% to - 80% power range that base on manufacturer declare the
conducted power density.
5.4.5. EST DEVIATION


Page 50 of 68
5.4.7. TEST RESULT OF ANTENNA POWER ERROR

Transmitting mode:

Humidity: 55 % RH
Conducted RF output
Rated power Antenna Power
Test Voltage Test Frequency power
(mW) Error (%)
(mW)
2405MHz 0.036 0.05 -28.00
5.0V 2430MHz 0.042 0.05 -16.00
2470MHz 0.037 0.05 -26.00
2405MHz 0.038 0.05 -24.00
4.5V 2430MHz 0.041 0.05 -18.00
2470MHz 0.032 0.05 -36.00
2405MHz 0.039 0.05 -22.00
5.5V 2430MHz 0.045 0.05 -10.00
2470MHz 0.037 0.05 -26.00
Limit : +20%, -80% (Base on manufacturer declare antenna power density)

Page 51 of 68
5.5. IMITATION OF COLLATERAL EMISSION OF RECEIVER MEASUREMENT

5.5.1. LIMIT
Item Limits
≦4nW (f<1GHz)
RX Spurious
Emission:
≦20nW (1GHz≦f)
Attenuation Auto
100 kHz (below 1GHz emissions)
RB
1 MHz (above 1GHz emissions)
100 kHz (below 1GHz emissions)
VB
1 MHz (above 1GHz emissions)
Detector Peak
Trace Max Hold
Sweep Time Auto

1. EUT have the continuous reception mode and fixed only one channelize.
2. Setting of SA is following as RB / VB: 100 kHz (below 1GHz emissions) / 1 MHz
(above 1GHz emissions) /
AT: 10dB / Ref: 0dBm / Sweep time: Auto / Sweep Mode: Continuous sweep / Detect
mode: Positive peak / Trace mode: Max hold
3. SA set RB: 100kHz and VB: 100kHz. Then adjust to start frequency 30MHz and
stop frequency 1000MHz. Search to mark peak reading value + cable loss shall
be less than 4nW
4. SA set RB: 1MHz and VB: 1MHz. Then adjust to start frequency 1000MHz and
stop frequency 12500MHz. Search to mark peak reading value + cable loss shall
be less than 20nW
5. If power level of lower emissions are more than 1/10 of limit (.0.4nW for f < 1GHz,
2nW for f >= 1GHz), all those are to be indicated in the 2nd and 3rd lines. If others
are 1/10 or less more of the limit, no necessary to be indicated.
Page 52 of 68


The EUT was programmed to be in continuously reception mode.
5.5.8. TEST RESULT OF LIMITATION OF COLLATERAL EMISSION OF RECEIVER

Humidity: 55 % RH
Note: The worst test channel of all channels was showed as the follow:
Test Voltage: 5.5V
RX-Frequency Band 1 (30 MHz ≦ f < 1000 MHz)
Page 53 of 68

Page 54 of 68
Test Voltage: 5.0V


Page 55 of 68
Test Voltage: 4.5V


Page 56 of 68
5.6. TRANSMISSION ANTENNA GAIN (EIRP ANTENNA POWER) MEASUREMENT

5.6.1. LIMIT
Item Limits
≦6.91dBm/MHz (FH form 2427 - 2474.75 MHz)

EIRP Power Density ≦12.14dBm/MHz (OFDM,DS from 2400~2483.5MHz)
≦12.14dBm (Other from 2400~2483.5MHz)
Note: This test item is not applied for radio equipment with equivalent isotropic radiation power
lower than 12.14dBm/MHz, but Antenna Power(Conducted) limit is 10 mW/MHz (10
dBm/MHz), So the test item will not be applied to the transmission antenna which has a gain of
2.14dBi or less
5.6.2．MEASURING INSTRUMENTS AND SETTING

Please refer to section 5 in this report. The following table is the setting of spectrum analyzer.
Attenuation Auto
RBW/VBW 1 MHz
Detector Peak
Trace Max Hold
Sweep Time Auto
5.6.3．TEST PROCEDURES
1. Set EUT ad measuring antenna at the same height and roughly facing each other.
2. Move the measuring antenna height up and down within ± 50cm of EUT height and
swing it to find the maximum output of the measuring antenna. The output level at
the spectrum analyzer is read sa “E“.
3. Remove the EUT from the turn table and put the replacing antenna facing to
measuring antenna at same height. Set the standard signal generator (SSG) at
same frequency and transmit on then receive the signal
4. Swing the replacing antenna give a maximum receiving level.
5. Move the measuring antenna height up and down within ± 50cm of replacing
antenna height and swing it to find the maximum receiving level.
6. Set SSG output power at Pt to give the equivalent output level of “E” or calculate
Pt with SSG output which gives the nearest of “E” and difference (± 1dB). Record
the Pt.
7. Calculate EIRP by the formula below EIRP = Gt – L + Pt.
Gt: gain of replacing antenna (dBi)
L: feeder loss between SSG and replacing antenna
Pt: Output power of the SSG
8. If the antenna for the EUT has circular polarization, sum of V-field and H-field
will be result if measuring antenna is linear polarization.
Page 57 of 68

For EUT radiation measurement
For standard antenna measurement


5.6.7. RESULTS OF TRANSMISSION ANTENNA GAIN

Note: refer to section 5.6.1 the test item is not applicable.
Page 58 of 68
5.7. TRANSMISSION RADIATION ANGLE WIDTH (3DB BEAMWIDTH) MEASUREMENT

5.7.1. LIMIT
Item Limits
360/A (If A<1; then A=1)

3dB antenna beam width A = {EIRP Power [mW] / 16.36 for DS, OFDM} or
A = {EIRP Power [mW] / 4.9 for FH}
Note: This test item is not applied for radio equipment with equivalent isotropic radiation power
lower than 12.14dBm/MHz, but Antenna Power(Conducted) limit is 10 mW/MHz (10
dBm/MHz), So the test item will not be applied to the transmission antenna which has a gain of
2.14dBi or less
Attenuation Auto
Span Frequency 0 MHz
RBW 1 MHz
VBW 1 kHz
Detector Peak
Trace Max Hold
Sweep Time Auto

1. Set EUT and measuring antenna at the same height and roughly facing each other.
2. Set spectrum analyzer with condition in section 4.7.2 and tune reference level to
observe receiving signal position.
3. Rotate directions of the EUT horizontally and vertically to find the maximum
receiving power.
4. Move the measuring antenna height up and down within ± 50cm of EUT height and
swing it to find the maximum output of measuring antenna. The output level at the
spectrum analyzer is read as “E”
5. Calculate permitted radiation angle in horizontal and vertical using EIRP
measured in another test method.
6. Calculate 3dB antenna beam width by the formula below 360/A (If A<1; then A=1).
A = {EIRP Power [mW] / 16.36 for DS, OFDM} or
A = {EIRP Power [mW] / 4.9 for FH}
Page 59 of 68


5.7.7. TEST RESULT OF TRANSMISSION RADIATION ANGLE WIDTH (3DB BEAMWIDTH)

Note: refer to section 5.7.1 the test item is not applicable.
Page 60 of 68
5.8. RADIO INTERFERENCE PREVENTION CAPABILITY MEASUREMENT

5.8.1. LIMIT
Item Limits
Identification code ≧48 bits
5.8.2. MEASURING ID CODE SOFTWARE
Item Limits
MAC IP List MAC Scan

1. In the case that the EUT has the function of automatically transmitting the
identification code: a. Transmit the predetermined identification codes form EUT. b.
Check the transmitted identification codes with the demodulator.
2. In the case of receiving the identification ocde: a. Transmit the
predetermined identification codes form the counterpart. b . Check if communication
is normal. c. Transmit the signals other than predetermined ID codes form
the counterpart. d. check if the EUT stops the transmission, or if it displays
that idnetification codes are different from the predetermined ones.


The EUT was programmed to be in normal transmitting mode.
Page 61 of 68
5.8.7. TEST RESULT OF RADIO INTERFERENCE PREVENTION CAPABILIT

Test result: CONFORM
Page 62 of 68
5.9. CONSTRUCTION PROTECTION CONFIRMATION METHOD

5.9.1. LIMIT
The high-frequency section and modulation section of the radio equipment except for
the antenna system shall not be capable of being opened easily.
5.9.2. CONFIRMATION METHOD

The RF and modulation portions are protected against illegal modification as following method:
Protected Method Description
2.4G Module Package of RF (TLSR8516) and Modulation

IC Package
(TX; 16MHz) portions is BGA type.
we will add some warning statements on the user manual to

User manual
against illegal modification
Page 63 of 68
APPENDIX A: PHOTOGRAPHS OF THE TEST SETUP

Page 64 of 68
APPENDIX B: PHOTOGRAPHS OF THE EUT

ALL VIEW OF EUT
TOP VIEW OF EUT

Page 65 of 68
BOTTOM VIEW OF EUT
FRONT VIEW OF EUT

Page 66 of 68
BACK VIEW OF EUT
LEFT VIEW OF EUT

Page 67 of 68
RIGHT VIEW OF EUT
OPEN VIEW OF EUT

Page 68 of 68
INTERNAL VIEW OF EUT-1
Antenna
INTERNAL VIEW OF EUT-2
----END OF REPORT----

Japan Radio Test Report: Attestation of Global Compliance (Shenzhen) Co., LTD

Uploaded by

Copyright:

Available Formats

Japan Radio Test Report: Attestation of Global Compliance (Shenzhen) Co., LTD

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Japan Radio Test Report: Attestation of Global Compliance (Shenzhen) Co., LTD

Uploaded by

Copyright:

Available Formats

Page 1 of 68

Japan radio Test Report

Report No.: AGC00688180207TE01

PRODUCT DESIGNATION : 2.4G Wireless Mouse Receiver

BRAND NAME : SANWA SUPPLY

TEST MODEL : SANWA RC5

CLIENT : Sanwa Supply Inc.

DATE OF ISSUE : Mar. 28, 2018

Attestation of Global Compliance (Shenzhen) Co., Ltd.

TABALE OF CONTENTS ..................................................................................................................................... 2

1. TEST RESULT CERTIFICATION

Applicant Name Sanwa Supply Inc.

Address 1-10-1 Tamachi Okayama City 700-0825 Japan

Manufacturer Name Shenzhen Hangshi Technology Co., Ltd

Brand Name SANWA SUPPLY

Test Model SANWA RC5

Date of Test Mar. 21, 2018 to Mar. 28, 2018

Test Result Pass

Max Zhang(Zhang Yi) Mar. 28, 2018

Bart Xie(Xie Xiaobin)

2. SANWA SUPPLY INFORMATION

2.1 EUT DESCRIPTION

Product Designation 2.4G Wireless Mouse Receiver

Model Name SANWA RC5

Hardware Version N 20120722

Software Version V1.0

Modulation Type GFSK

Operation Frequency 2405~2470MHz

Channel No. 8 Channels

Rated Power Density 0.05mW

Power Supply DC 5.0V

(5.5V)High Voltage + 10% of Normal Voltage

Test Channel 2405MHz, 2430MHz, 2470MHz

2.2 CHANNEL LIST

Frequency Band Channel Number Frequency

2.3 DESCRIPTION OF TEST MODES

Power Supply Voltage Fluctuation Test

3. TEST ITEMS AND THE RESULTS

Part Rule Section Description of Test Result

5.1 3 Frequency Error Complies

5.4 6 Antenna Power Error Complies

5.5 7 Limitation of Collateral Emission of Receiver Complies

5.9 Note1 Carrier Sense Capability N/A

5.10 Note 2 Construction Protection Confirmation Complies

Note 1: MIC Notice No.88 Appendix No.43

Company Name: Attestation of Global Compliance (Shenzhen) Co., Ltd.

2/F., Building 2, No.1-No.4, Chaxi Sanwei Technical Industrial Park, Gushu,

4.2 LIST OF TEST EQUIPMENTS

Power meter R&S NRVD 832378/027 Jul.14, 2017 Jul.13, 2018

Power sensor ANRITSU MA2491A 0341138 Jul.14, 2017 Jul.13, 2018

Pre-amplifier ANRITSU MH648A M09961 Jul.14, 2017 Jul.13, 2018

RF Cable SUIRONG 30MHZ-18GHZ N/A Jul.14, 2017 Jul.13, 2018

Attenuator MINI-CIRCUITS VAT-10+ 15542 Jul.14, 2017 Jul.13, 2018

4.3 ENVIRONMENTAL CONDITIONS

Frequency Tolerance (2405~2470MHz) ≦50ppm

5.1.2. TEST PROCEDURES

5.1.3. TEST SETUP LAYOUT

5.1.4. TEST DEVIATION