Gear Pumps

aerospace
climate control
Gear Pumps electromechanical
filtration
Series PGP fluid & gas handling
hydraulics
Fixed Displacement Pumps, pneumatics
Aluminium Designs process control
sealing & shielding
Catalogue HY02-8001/UK Aluminium Body Gear Pumps
Contents Series PGP500
Contents Page 4-1-

PGP500 Characteristics .................................................................................. 3
PGP502 Ordering Code ....................................................................... 4
PGP502 Performance curves ............................................................... 5
PGP502 Technical Data / Dimensions ................................................. 6
PGP505 Ordering Code ....................................................................... 7
PGP505 Performance curves ............................................................... 8
PGP511 Ordering Code ..................................................................... 11
PGP511 Operating Conditions ........................................................... 12
PGP511 Performance curves ............................................................. 13
PGP511 Technical Data / Dimensions ............................................... 14
PGP517 Ordering Code ..................................................................... 17
PGP517 Operating Conditions ........................................................... 18
PGP517 Performance curves ............................................................. 19
PGP500 Ordering Example (Multiple Pumps).................................... 22
Split Gear Pumps .......................................................................................... 23
Nomograph .................................................................................................... 24
Nomograph for Pipe Velocity ......................................................................... 24
Shaft Loads / Fluids ....................................................................................... 25
PI PGP-PGM UK.PMD RH
4-1- 2 Parker Hannifin Corporation

Hydraulics Group
Characteristics Series PGP500
PGP 500 pumps offer superior performance, high effi-

ciency and low noise operation at high operating pressures.
They are produced in four frame sizes (PGP 502, PGP
505, PGP 511, PGP 517) with displacements ranging from
0.8 to 70 cm³/rev. A wide variety of standard options is
available to meet specific application requirements.
Characteristics
u Up to 280 bar continuous operation u High efficiency
High strength materials and large journal diameters Pressure balanced bearing blocks assure maximum
provide low bearing loads for high pressure opera-
tion.
efficiency under all operating conditions. 4
u Application flexibility
u Low noise International mounts and connections, integrated
PGP 502 - 9 tooth gear profile, PGP 505 and 517 - 13 valve capabilities and common inlet multiple pump
tooth gear profile, PGP 511 - 12 tooth gear profile configurations provide unmatched design and applica-
and optimized flow metering provide reduced pressure tion versatility.
pulsation and exceptionally quiet operation (PGP511
also available as noise reduced “stealth“ version). u Large range of integrated valves
Technical data
Pump type Heavy-duty, aluminium, external gear. Fluid viscosity Range of operating viscosity
Mounting SAE, rectangular, thru-bolt standard 8 to 1000 mm²/s (511 & 517)
specials on request. 20 to 1000 mm²/s (502 & 505)
Max. permissible operating pressure
Ports SAE and metric split flanges and others dependent on viscosity.
Shaft style SAE splined, keyed, tapered, cylindrical
tang drive, specials on request. Viscosity range for cold start
1000 to 2000 mm²/s at
Speed 500 - 5000 rpm, see Technical Data operating pressure pa10 bar and
Theor. displacement See Technical Data speed n a1500 rpm.
Drive Drive direct with flexible coupling is Range of ambient
recommended. temperature -40 °C to +70 °C
Axial / Radial load Units subject to axial or radial loads Filtration According to ISO 4406 Cl. 18/16/13
must be specified with an outboard Direction of rotation Clockwise, counter-clockwise or double.
bearing. (looking at the Attention! Drive pump only in
Inlet pressure Operating range 0.8 to 2 bar abs. drive shaft) indicated direction of rotation.
Min. inlet pressure 0.5 bar abs. Short time -ULTIPLEPUMP s!VAILABLEINTWOORTHREESECTION
without load. Consultation is recommended. assemblies configuration.
Outlet pressure See Technical Data s-AXSHAFTLOADMUSTBECONFORMTO
the limitations shown in the shaft loading
Pressure rising rate Max. 3000 bar/s rating table in this catalogue.
Flow velocity See Nomograph for Pipe Velocity s-AXLOADISDETERMINEDBYADDING
the torque values for each pumping
Hydraulic fluids Hydraulic oil HLP, DIN 51524-2 section that will be simultaneously
loaded.
Fluid temperature Range of operating temperature Separate or common Separate inlet configuration:
-15 to +80 °C. INLETCAPABILITY s%ACHGEARHOUSINGHASINDIVIDUALINLET
Max. permissible operating pressure and outlet ports.
dependent on fluid temperature. Common inlet configuration:
Temperature for cold start -20 to -15 °C s4WOGEARSETSSHAREACOMMONINLET
at speed a 1500 rpm.
dependent on fluid temperature.

Hydraulics Group
Ordering Code Series PGP502
PG 502 B 1 B 1
Gear Type Unit Dis- Rotation Shaft Flange Shaft Inlet Outlet No rear ports
design place- seal (rear ports on request)
side ports
ment option
Code Type Code Port options

P Pump
E3E2 1/2" - 14 BSP thread/
3/8" - 19 BSP thread
J4J3 Ø12 mm - Ø30 mm - M6
Unit square flange/
Code Ø8 mm - Ø30 mm - M6
Pump
square flange
A Single unit
Example: E3 = inlet port
B Multiple unit E2 = outlet port
Displacement
Code Shaft seal
Code ccm
X No seal
0008 0.8
N NBR
0012 1.2
0016 1.6
0021 2.1
0025 2.5
0033 3.3 Code Flange
0036 3.6
0043 4.3 D1 52.2x72.0 - Ø25.4
rectangular
0048 4.8
0058 5.8 H1 82.5 - Ø50.8 SAE ”A-A”
2 bolt flange
0062 6.2
0079 7.9 P3 40.0x40.0 - Ø32.0 w/ seal,
thrubolt flange
P4 40.0x40.0 - Ø32.0 w/ seal f.
short shaft, thrubolt flange
Code Rotation
C Clockwise
A Counter-
clockwise
Code Shaft
H1 2) Ø10, 3.0 key, no thread, 36L,

parallel
P2 3) Ø9.35, 8.8L, 2.4 key, M6,
taper 1:8
V1 4) 5x6.5 long shaft w/o coupling
tang drive
V2 5) 5x4.5 short shaft w/o coupling
tang drive
2)
Only used with flange H1, D1.
3)
Only used with flange D1.
4)
Only used with flange H1.
5)
Only used with flange P3, P4.

Hydraulics Group
Performance curves Series PGP502
PGP502 - 0.8 CC PGP502 - 2.1 CC

2.0 Flow [l/min.] 5.0 10.0
Flow [l/min.]
Input Power [kW]
Input Power [kW]

1.8 3.6 4.5 9.0
Flow at n=4000 rpm
Flow at n=4000 rpm
1.6 3.2 4.0 8.0
1.4 2.8 3.5 7.0
I. Power at n=4000 rpm

1.2 2.4 3.0 6.0

1.0 2.0 2.5 5.0
0.8 1.6 2.0 4.0
0.6 1.2 Flow at n=1500 rpm 1.5 3.0

Flow at n=1500 rpm
4
0.4 0.8 1.0 2.0
Flow at n=500 rpm Flow at n=500 rpm

0.2 0.4 0.5 1.0
I. Power at n=500 rpm I. Power at n=500 rpm

0 0 0 0
0 50 100 150 200 250 300 0 50 100 150 200 250 300
Pressure [bar] Pressure [bar]
PGP502 - 3.6 CC PGP502 - 6.2 CC
8.0 16 10.0 20.0
Flow [l/min.]
Flow [l/min.]
Input Power [kW]
Input Power [kW]
7.5 15 Flow at n=3000 rpm

Flow at n=4000 rpm 9.0 18.0
7.0 14
6.5 13 8.0 16.0

6.0 12
5.5 11 7.0 14.0
5.0 10 I. Power at n=3000 rpm

6.0 12.0
4.5 9.0
4.0 8.0 5.0 10.0
Flow at n=1500 rpm
3.5 7.0
4.0 8.0
3.0 6.0
Flow at n=1500 rpm
2.5 5.0 3.0 6.0
2.0 4.0
I. Power at n=1500 rpm 2.0 4.0
1.5 3.0
Flow at n=500 rpm
1.0 2.0 Flow at n=500 rpm
1.0 2.0
0.5 1.0 I. Power at n=500 rpm
0 0 0 0
0 50 100 150 200 250 300 0 50 100 150 200 250 300
PI PGP-PGM UK.PMD RH Fluid temperature: 45 °C± 2K ; Viscosity: 36mm2/s ; Inlet pressure: 0.9 + 0.1 bar absolute

Hydraulics Group
Technical Data / Dimensions Series PGP502
PGP502 A XXXX Y P2 D1 N SS PP B1 B1 “Y” = C (clockwise rotation)

= A (counter-clockwise rotation)
Displacement Dimension Inlet port Outlet port Speed of Working Order number
rotation pressure direction of rotation
XXXX cm3/rev A B C F F min. max. max. counter-
mm mm mm SS G mm PP G mm rpm rpm bar clockwise clockwise
0008 0.8 32.6 65.3 94.0 E3 G ½" 33 E2 G 3/8" 24 500 5000 280 330 9111 346 330 9112 233
0012 1.2 33.4 66.8 96.0 E3 G ½" 33 E2 G 3/8" 24 500 5000 280 330 9111 347 330 9112 234
0016 1.6 34.1 68.3 97.5 E3 G ½" 33 E2 G 3/8" 24 500 5000 280 330 9111 348 330 9112 235
0021 2.1 34.9 69.9 99.0 E3 G ½" 33 E2 G 3/8" 24 500 4500 280 330 9111 349
0025 2.5 35.7 71.5 100.5 E3 G ½" 33 E2 G 3/8" 24 500 4500 280 330 9111 350 330 9112 236
0033 3.3 37.2 74.5 103.5 E3 G ½" 33 E2 G 3/8" 24 500 4000 280 330 9111 351 330 9112 237
0036 3.6 37.8 75.6 104.5 E3 G ½" 33 E2 G 3/8" 24 500 4000 260 330 9111 352 330 9112 238
0043 4.3 39.2 78.5 107.5 E3 G ½" 33 E2 G 3/8" 24 500 4000 250 330 9111 353
0048 4.8 40.0 80.0 109.0 E3 G ½" 33 E2 G 3/8" 24 500 3800 230 330 9111 354 330 9112 239
0058 5.8 41.9 83.8 113.0 E3 G ½" 33 E2 G 3/8" 24 500 3800 200 330 9111 355 330 9112 240
0062 6.2 42.6 85.3 114.5 E3 G ½" 33 E2 G 3/8" 24 500 3500 180 330 9111 356 330 9112 241
0079 7.9 45.8 91.6 121.0 E3 G ½" 33 E2 G 3/8" 24 500 3000 160 330 9111 357
Dimensions (clockwise rotation shown)
29 -1.2 15
68
20.35 -1.2
52.4
13 -0.7
4
5.74 -0.38
(34.3)
26.2
5
Ø9.3
9.5
71.9
87.6
70
8.85±0.5 Inlet
A
ØB
(C)
R 8
.2
ØF Outlet
4x
Ø7
G
4x
2.4 h8
Taper 1:8
Ø25.4 f7
60
Washer 6 G
ØF
Installation torque
6 +2 Nm Woodruff key 2.4x5-D13

Hydraulics Group
PG 505 B 1 B 1
side ports
ment option

P Pump
1/2" - 14 BSP thread
J7J5 Ø20 mm - Ø40 mm - M6
square flange/
Unit Ø15 mm - Ø35 mm - M6
Code square flange
Pump
A Single unit Example: J7 = inlet port

J5 = outlet port
Single dis-
M tributor unit
4
B Multiple unit Code Shaft seal
X No seal
N NBR
Displacement
Code ccm
0030 3.0
0040 4.0 Code Flange
0060 6.0
56.0x73.0 - Ø30.0
0080 8.0 D2 5)
rectangular
0100 10.0
82.5 - Ø50.8 SAE ”A-A”
0120 12.0 H1
2 bolt flange
106.4 - Ø82.55 SAE ”A”
H2 6)
2 bolt flange
Code Rotation
5)
Only used with ports J*J*.
C Clockwise 6)
Only used with ports E*E*.
A Counter-
clockwise
Code Shaft
9T, 16/32DP, 32L, SAE ”A”

A1 2)
spline
Ø12.7, 3.2 key, no thread, 38L,
J1 2)
parallel
Ø15.88, 4.0 key, no thread,
K1 3)
32L, SAE ”A”, parallel
Ø14.25, 5.5L, 3.0key, M10x1,
Q2 4)
taper 1:8
2)
Only used with flange H1, H2.
3)
4)

Hydraulics Group
PGP505 - 3.0 CC PGP505 - 6.0 CC

8.0 16 16 32
Flow [l/min.]
Flow [l/min.]
Input Power [kW]
Input Power [kW]

7.5 15 15 30
7.0 14 14 28
6.5 13 13 26
6.0 12 Flow at n=4000 rpm 12 24
5.5 11 11 22 Flow at n=3600 rpm
5.0 10 10 20
4.5 9.0 9.0 18
4.0 8.0 8.0 16

3.5 7.0 7.0 14
3.0 6.0 6.0 12

2.5 5.0 5.0 10
2.0 4.0 4.0 8.0
1.5 3.0 3.0 6.0

1.0 2.0 2.0 4.0
0.5 1.0 1.0 2.0
0 0 0 0
0 50 100 150 200 250 300 0 50 100 150 200 250 300
PGP505 - 10.0 CC PGP505 - 12.0 CC
16 32 16 32
Flow [l/min.]
Flow [l/min.]
Input Power [kW]
Input Power [kW]
15 30 15 30
Flow at n=2400 rpm
14 28 Flow at n=2800 rpm 14 28
13 26 13 26
12 24 12 24
11 22 11 22
10 20 10 20
Flow at n=1500 rpm
9.0 18 9.0 18
8.0 16 8.0 16
Flow at n=1500 rpm
7.0 14 7.0 14
6.0 12 6.0 12
5.0 10 5.0 10
4.0 8.0 4.0 8.0
3.0 6.0 3.0 6.0 Flow at n=500 rpm

Flow at n=500 rpm
2.0 4.0 2.0 4.0
1.0 2.0 1.0 2.0

0 0 0 0
0 50 100 150 200 250 300 0 50 100 150 200 250 300
PI PGP-PGM UK.PMD RH Fluid temperature: 45 °C ± 2K ; Viscosity: 36mm2/s ; Inlet pressure: 0.9 + 0.1 bar absolute

Hydraulics Group
PGP505 A XXXX Y A1 H2 N SS PP B1 B1 “Y” = C (clockwise rotation)

XXXX cm3/rev A B C SS G F PP G F min. rpm max. rpm max. bar clockwise counter-clockwise
0030 3.0 35.9 41.1 79.8 E5 3/4"-14 42.0 E3 1/2"-14 34.0 500 4000 275 331 9111 385
BSP BSP
0040 4.0 37.2 43.8 79.8 E5 3/4"-14 42.0 E3 1/2"-14 34.0 500 4000 275 331 9111 386
BSP BSP
3/4"-14 1/2"-14
0060 6.0 39.8 49.1 84.8 E5 BSP
42.0 E3 BSP
34.0 500 3600 275 331 9111 387
0080 8.0 42.5 54.5 89.8 E5 3/4"-14 42.0 E3 1/2"-14 34.0 500 3000 275 331 9111 383 331 9112 136
BSP BSP
3/4"-14 1/2"-14
0100 10.0 45.2 59.8 100.8 E5 42.0 E3 34.0 500 2800 250 331 9111 388
BSP BSP
0120 12.0 47.9 65.2 104.8 E5 3/4"-14 42.0 E3 1/2"-14 34.0 500 2400 220 331 9111 389
BSP BSP
E
4
32 C 130
15.2 B 53.2
6.2 ØF
G
48
Ø82.55 -0.05
82
13.1
9.7 2x Ø11
A 106.4
Inlet
40
32.2
23.8 full spline
35
Ø16
SAE “A” spline

Outlet 9 teeth 16/32 DP
flat root side fit

Hydraulics Group
PGP505 A XXXX Y Q2 D2 N SS PP B1 B1 “Y” = C (clockwise rotation)

XXXX cm3/rev A B C SS d D G PP d D G min. rpm max. rpm max. bar clockwise counter-clockwise
0030 3.0 35.9 41.1 74.3 J7 20.0 40.0 M6 J5 15.0 35.0 M6 500 4000 275 331 9111 334
0040 4.0 37.2 43.8 76.4 J7 20.0 40.0 M6 J5 15.0 35.0 M6 500 4000 275 331 9111 039 331 9112 061
0060 6.0 39.8 49.1 81.7 J7 20.0 40.0 M6 J5 15.0 35.0 M6 500 3600 275 331 9111 040 331 9112 077
0080 8.0 42.5 54.5 87.1 J7 20.0 40.0 M6 J5 15.0 35.0 M6 500 3000 275 331 9111 041 331 9112 078
0100 10.0 45.2 59.8 92.4 J7 20.0 40.0 M6 J5 15.0 35.0 M6 500 2800 250 331 9111 087 331 9112 033
0120 12.0 47.9 65.2 97.8 J7 20.0 40.0 M6 J5 15.0 35.0 M6 500 2400 220 331 9111 246 331 9112 135

E
35 C 68
15.3 B 56.0
5.5 ØD 28
Ød
45° 45°
30.5
24.5
Ø30 f8
73.0
85
82
13.1
9.8 G
A 4x Ø6.5
Inlet
32.4
Woodruff key 3x5-DIN 6888
20.9
M10 x 1
38.0
1.7
3
34.5
Ø14.63
Taper 1:8
Installation torque
17 +5 Nm Outlet

Hydraulics Group
PG 511 B 1 B 1
side ports
ment option
Code Type
P Pump Code Port options

Unit 1/2" - 14 BSP thread
Code Code Shaft seal rec. from 4 ccm to 16 ccm
Pump
X No seal E6E5 1"-11 BSP thread/
NBR 3/4"-14 BSP thread
A Single unit N
rec. from 14 ccm to 23 ccm
V FPM
Single dis- E7E5 1 1/4"-11 BSP thread/
M tributor unit 3/4"-14 BSP thread
J7J5 Ø20 mm-Ø40 mm-M6 square flange
B Multiple unit Ø15 mm-Ø35 mm-M6 square flange
J9J8 Ø26 mm-Ø55 mm-M8 square flange
Ø18 mm-Ø55 mm-M8 square flange
4
Displacement rec. from 14 ccm to 33 ccm
Code ccm L1L1 Ø13 mm-Ø30 mm-M6 diamond flange
0040 4.0 Ø13 mm-Ø30 mm-M6 diamond flange
0060 6.0 rec. from 4 ccm to 8 ccm
0080 8.0 L2L1 Ø19 mm-Ø40 mm-M8 diamond flange
0140 14.0 L2L2 Ø19 mm-Ø40 mm-M8 diamond flange
0230 23.0
0270 27.0
0310 31.0 Example: J7 = inlet port
0330 33.0 J5 = outlet port
Code Rotation
C Clockwise
A Counter- clock-
wise
B Bi-directional
Code Flange
Code Shaft
71.4x96.0 - Ø36.47 rectangular
A1 2) 9T, 16/32DP, 32L, SAE ”A” spline D3
72.0x100.0 - Ø80 rectangular
C1 3) 11T, 16/32DP, 38.2L, SAE 19-4 spline D4
106.4 - Ø82.55 SAE ”A”
F1 4) 9T, B17x14, 23L, DIN 5482 spline H2
2 bolt flange
K1 2) Ø15.88, 4.0 key, no thread, 32L, 146.1 - Ø101.06 SAE ”B”
SAE ”A”, parallel H3
2 bolt flange
L6 2) Ø19.05, 4.8 key, no thread, 32L, 60.0x60.0 - Ø50.0 w. seal O’,
SAE 19-1, parallel Q2
thrubolt flange
S1 4) Ø17.0, 7.7L, 3.0 key, M12x1.5, taper 1:5 60.0x60.0 - Ø50.0 w. seal O’,
S2 5) Ø16.65, 12.0L, 3.2 key, M12x1.5, Q4
thrubolt flange
taper 1:8
S4 5) Ø16.65, 12.0L, 4.0 key, M12x1.5,
taper 1:8
2)
3)
4)
Only used with flange D4, Q2, Q4.
5)

Hydraulics Group
Operating Conditions Series PGP511
Pressure depending on speed

250
Pressure p [bar]
4.0 TO 19.0 cc 4.0 TO 16.0 cc
23.0 cc
19 cc
200
27.0 cc
31.0 cc
150
33.0 cc
100
500 1000 1500 2000 2500 3000 3500
Speed n [rpm]
Pressure depending on viscosity

250
4.0 TO 19.0 cc
Pressure p [bar]
23.0 cc
200
27.0 cc
31.0 cc
150
33.0 cc
100
8 10 12 15 20 50 100 200 500 1000
Viscosity N [mm /s (cSt)]

2

Hydraulics Group
PGP511 - 6.0 CC PGP511 - 10.0 CC

16 32 20 40
Flow [l/min.]
Flow [l/min.]
Input Power [kW]
Input Power [kW]

15 30 19 38
18 36
14 28 Flow at n=3600 rpm
17 34
13 26 16 32
12 24 15 30
11 22 14 28
Flow at n=4000 rpm
13 26
10 20
12 24
9.0 18 11 22
8.0 16 10 20
7.0 14 9.0 18
8.0 16
6.0 12 Flow at n=1500 rpm
7.0 14
5.0 10
Flow at n=1500 rpm
6.0 12
4
4.0 8.0 5.0 10
3.0 6.0 4.0 8.0
Flow at n=500 rpm 2.0 4.0
1.0 2.0 1.0 2.0
0 0 0 0
0 50 100 150 200 250 300 0 50 100 150 200 250 300
PGP511 - 19.0 CC PGP511 - 33.0 CC
40 80
Flow [l/min.]
Flow [l/min.]
Input Power [kW]
Input Power [kW]
30 60 38 76
Flow at n=2800 rpm
28 56 36 72
34 68
32 64
24 48
30 60
22 44 28 56
20 40 26 52
Flow at n=1500 rpm
24 48
18 36
22 44
16 32
20 40
Flow at n=1500 rpm
14 28 18 36
12 24 16 32
14 28
10 20
12 24
8.0 16 I. Power at n=1500 rpm
I. Power at n=1500 rpm 10 20
6.0 12 8.0 16
4.0 8.0 6.0 12
4.0 8.0
2.0 4.0
0 0
0 50 100 150 200 250 300 0 0
0 50 100 150 200 250 300
2
PI PGP-PGM UK.PMD RH Fluid temperature: 45 °C ± 2K ; Viscosity: 36mm /s ; Inlet pressure: 0.9 + 0.1 bar absolute

Hydraulics Group
PGP511 A XXXX Y A1 H2 N SS PP B1 B1 “Y” = C (clockwise rotation)

min. max. counter-
XXXX cm3/rev A B C SS G F PP G F rpm rpm max. bar clockwise clockwise
0040 4.0 42.6 47.0 86.7 E5 3/4"-14 BSP 42.0 E3 1/2"-14 BSP 34.0 500 3500 250
0060 6.0 44.1 50.1 89.8 E5 3/4"-14 BSP 42.0 E3 1/2"-14 BSP 34.0 500 3500 250 334 9111 044 334 9112 621
0080 8.0 45.7 53.3 93.0 E5 3/4"-14 BSP 42.0 E3 1/2"-14 BSP 34.0 500 3500 250 334 9111 562 334 9112 622
0100 10.0 47.3 56.5 96.1 E5 3/4"-14 BSP 42.0 E3 1/2"-14 BSP 34.0 500 3500 250 334 9111 130 334 9112 628
0110 11.0 48.1 58.0 97.7 E5 3/4"-14 BSP 42.0 E3 1/2"-14 BSP 34.0 500 3500 250 334 9111 039 334 9112 023
0140 14.0 50.4 62.8 102.4 E5 3/4"-14 BSP 42.0 E3 1/2"-14 BSP 34.0 500 2700 250 334 9111 563 334 9112 623
0160 16.0 52.0 65.9 105.6 E6 1"-11 BSP 50.0 E5 3/4"-14 BSP 42.0 500 3500 250 334 9111 092 334 9112 060
0190 19.0 54.4 70.6 110.3 E6 1"-11 BSP 50.0 E5 3/4"-14 BSP 42.0 500 3200 250 334 9111 193 334 9112 624
0230 23.0 57.5 76.9 116.6 E6 1"-11 BSP 50.0 E5 3/4"-14 BSP 42.0 500 2700 210 334 9111 564
0270 27.0 60.7 83.2 122.9 E6 1"-11 BSP 50.0 E5 3/4"-14 BSP 42.0 500 2300 180 334 9111 942 334 9112 494
0310 31.0 63.8 89.5 129.2 E6 1"-11 BSP 50.0 E5 3/4"-14 BSP 42.0 500 2000 160 334 9111 207 334 9112 229
0330 33.0 65.4 92.6 132.3 E6 1"-11 BSP 50.0 E5 3/4"-14 BSP 42.0 500 1800 150 334 9112 773

E
31.8 C 130
19.1 B 53.2
6.4 ØF
47.5
Ø82.55 -0.05
101.6
15.9
11.3 2x Ø11
A 106.4
Inlet
24.2
16.6
44.8
44.8
SAE “A” spline

9 teeth 16/32 DP
Outlet

Hydraulics Group
PGP511 A XXXX Y S1 D4 N SS PP B1 B1 “Y” = C (clockwise rotation)

0040 4.0 42.6 47.0 86.7 J7 20 40 M6 J5 15 35 M6 500 3500 250 334 9111 149 334 9112 289
0060 6.0 44.1 50.1 89.8 J7 20 40 M6 J5 15 35 M6 500 3500 250 334 9111 465 334 9112 298
0080 8.0 45.7 53.3 93.0 J7 20 40 M6 J5 15 35 M6 500 3500 250 334 9111 151 334 9112 291
0100 10.0 47.4 56.5 96.1 J7 20 40 M6 J5 15 35 M6 500 3500 250 334 9111 466 334 9112 292
0110 11.0 48.1 58.0 97.7 J7 20 40 M6 J5 15 35 M6 500 3500 250 334 9111 152 334 9112 238
0140 14.0 50.4 62.8 102.4 J7 20 40 M6 J5 15 35 M6 500 3400 250 334 9111 153 334 9112 239
0160 16.0 52.0 65.9 105.6 J7 20 40 M6 J5 15 35 M6 500 3000 250 334 9111 154 334 9112 120
0190 19.0 54.4 70.6 110.3 J9 26 55 M8 J8 18 55 M8 500 3250 250 334 9111 970
0230 23.0 57.5 76.9 116.6 J9 26 55 M8 J8 18 55 M8 500 2750 225 334 9111 971
0270 27.0 60.7 83.2 122.9 J9 26 55 M8 J8 18 55 M8 500 2350 190 334 9111 972 334 9112 807
0310 31.0 63.8 89.5 129.2 J9 26 55 M8 J8 18 55 M8 500 2100 165 334 9111 526
0330 33.0 65.4 92.6 132.3 J9 26 55 M8 J8 18 55 M8 500 2000 155 334 9111 973
4
E
37.7 C 90
19.1 B 72
7.2 ØD 36
Ød
45°
45°
43.5
34.5
Ø80 -0.05
100.0
101.6
118
15.9
12.5 G
7.7 A 4x Ø9
Inlet
30.0
M12 x 1.5
Woodruff key 3x5-DIN 6888

17.0
1.8
44.8
3
Ø17.0
44.8
Installation torque
28 +5 Nm Taper 1:5
Outlet

Hydraulics Group
PGP511 A XXXX Y S2 D3 N SS PP B1 B1 “Y” = C (clockwise rotation)

= A (counter clockwise rotation)
0040 4.0 42.6 47.0 86.7 L1 13 30 M6 L1 13 30 M6 500 3500 250 334 9111 403 334 9112 398
0060 6.0 44.1 50.1 89.8 L1 13 30 M6 L1 13 30 M6 500 3500 250 334 9111 404 334 9112 395
0080 8.0 45.7 53.3 93.0 L1 13 30 M6 L1 13 30 M6 500 2500 250 334 9111 091 334 9112 397
0100 10.0 47.3 56.5 96.1 L2 19 40 M8 L1 13 30 M6 500 3500 250 334 9111 975 334 9112 618
0110 11.0 48.1 58.0 97.7 L2 19 40 M8 L1 13 30 M6 500 3500 250 334 9111 976 334 9112 399
0140 14.0 50.4 62.8 102.4 L2 19 40 M8 L1 13 30 M6 500 3100 250 334 9111 292 334 9112 400
0160 16.0 52.0 65.9 105.6 L2 19 40 M8 L1 13 30 M6 500 2700 250 334 9111 293 334 9112 601
0190 19.0 54.4 70.6 110.3 L2 19 40 M8 L2 19 40 M8 500 2300 250 334 9111 977
0230 23.0 57.5 76.9 116.6 L2 19 40 M8 L2 19 40 M8 500 1900 225 334 9111 295
0270 27.0 60.7 83.2 122.9 L2 19 40 M8 L2 19 40 M8 500 1600 190 334 9111 296
0310 31.0 63.8 89.5 129.2 L2 19 40 M8 L2 19 40 M8 500 1500 165 334 9111 978
0330 33.0 65.4 92.6 132.3 L2 19 40 M8 L2 19 40 M8 500 1500 155 334 9111 297
Dimensions (clockwise rotation shown) E
39.7 C 89.5
19.1 B 71.4
5.0 ØD 35.7
Ød
41
32.5
96.0
102
114
15.9
Ø36.47 -0.05
12.0 G
A 4 x Ø8.5
Inlet
Woodruff key 27.7
3.2x6.5-DIN 6888
M12 x 1.5
15.4
1.5
44.8
3.2
Ø16.65
44.8
Installation torque Taper 1:8

28 +5 Nm
PI PGP-PGM UK.PMD RH Outlet

Hydraulics Group
PG 517 B 1 B 1
design place- seal side ports (rear ports on request)
ment option
Code Type
P Pump Code Port options
E6E5 1"-11 BSP thread/
3/4"-14 BSP thread
Unit
Code E7E6 1 1/4"-11 BSP thread/
Pump
1"-11 BSP thread
A Single unit
E8E6 1 1/2"-11 BSP thread/
Single 1"-11 BSP thread
M distributor rec. from 44 ccm to 70 ccm
unit J9J8 Ø26 mm-Ø55 mm-M8 square flange
Ø18 mm-Ø55 mm-M8 square flange
B Multiple unit rec. from 14 ccm to 52 ccm
L3L2 Ø27 mm-Ø51 mm-M10 diamond flange
Ø19 mm-Ø40 mm-M8 diamond flange
4
Displacement rec. from 14 ccm to 52 ccm
Code ccm P3P2 1"-M10 SAE metric flange
3/4"-M10 SAE metric flange
0140 14.0
0160 16.0
P4P3 1 1/4"-M10 SAE metric flange
0190 19.0
1"-M10 SAE metric flange
0230 23.0
0250 25.0
0280 28.0 P5P3 1 1/2"-M12 SAE metric flange
1"-M10 SAE metric flange
0330 33.0
0380 38.0
0440 44.0
Example: P4 = inlet port
0520 52.0
P3 = outlet port
0700 70.0
Code Shaft seal

Code Rotation X No seal
C Clockwise N NBR
A Counter- clock- V FPM
wise
Code Shaft Code Flange
13T, 16/32DP, 41.2L, D7 98.4x128.2 - Ø50.77

D1 2) rectangular
SAE ”B” spline
Ø22.2, 6.3key, no thread, H3 146.1 - Ø101.06 SAE ”B”
M1 2) 2 bolt flange
41.2L, SAE ”B”, parallel
Ø25.4, 6.3key, no thread,
M2 2)
46L, SAE ”B-B”, parallel
Ø21.59, 11.2L, 4.0key,
T1 3)
M14x1.5, taper 1:8
2)
3)

Hydraulics Group
Operating Conditions Series PGP517
Pressure depending on speed

250
Pressure p [bar]
14.0 to 38.0 cc 14.0 and 16.0 cc
33.0 and 38.0 cc 19.0 and 23.0 cc
44.0 cc
52.0 cc
200
25.0 and 28.0 cc
150
100
500 1000 1500 2000 2500 3000 3500
Speed n [rpm]
Pressure depending on viscosity

250
Pressure p [bar]
14.0 to 38.0 cc
44.0 cc
200
52.0 cc
150
100
8 10 12 15 20 50 100 200 500 1000
Viscosity N [mm2/s (cSt)]

Hydraulics Group
PGP517 - 14.0 CC PGP517 - 25.0 CC

40 80
Flow [l/min.]
Flow [l/min.]
Input Power [kW]
Input Power [kW]

38 76
30 60
Flow at n=3600 rpm
36 72
28 56
34 68
26 52 32 64
24 48 30 60
28 56
22 44
Flow at n=4000 rpm 26 52
20 40
24 48
18 36 22 44
16 32 20 40
Flow at n=1500 rpm
14 28 18 36
16 32
12 24
14 28
10 20
Flow at n=1500 rpm
12 24
4
8.0 16 10 20
6.0 12 8.0 16
I. Power at n=1500 rpm Flow at n=500 rpm
6.0 12
4.0 8.0
2.0 4.0 2.0 4.0
0 0 0 0
0 50 100 150 200 250 300 0 50 100 150 200 250 300
PGP517 - 44.0 CC PGP517 - 52.0 CC
65 130
80 160
Flow [l/min.]
Flow [l/min.]
Input Power [kW]
Input Power [kW]
60 120 75 150
Flow at n=2800 rpm
Flow at n=2400 rpm
55 110 70 140
65 130
50 100
60 120
45 90
55 110
40 80 50 100
35 70 45 90
Flow at n=1500 rpm
Flow at n=1500 rpm
40 80
30 60
35 70
25 50
30 60
20 40 25 50
20 40
15 30

10 20
5 10
0 0 0 0
0 50 100 150 200250 300 0 50 100 150 200 250 300
PI PGP-PGM UK.PMD RH Fluid temperature: 45 °C ± 2K ; Viscosity: 36mm2/s ; Inlet pressure: 0.9 + 0.1 bar absolute

Hydraulics Group
PGP517 A XXXX Y D1 H3 N SS PP B1 B1 “Y” = C (clockwise rotation)

Displace- Dimension Inlet port Outlet port Speed of Working Order number
ment rotation pressure direction of rotation
XXXX cm3/ A B C SS d G H W PP d G H W min. max. max. clockwise counter-
rev rpm rpm bar clockwise
0140 14.0 62.1 68.3 122.8 P2 3/4" M10 47.63 22.23 P2 3/4" M10 47.63 22.23 500 3000 250
0160 16.0 63.2 70.3 124.8 P3 1" M10 52.37 26.19 P2 3/4" M10 47.63 22.23 500 3400 250
0190 19.0 64.7 73.3 127.8 P3 1" M10 52.37 26.19 P2 3/4" M10 47.63 22.23 500 3300 250 333 9112 180
0230 23.0 66.7 77.4 131.9 P3 1" M10 52.37 26.19 P2 3/4" M10 47.63 22.23 500 3300 250 333 9111 193 333 9112 177
0250 25.0 67.7 79.4 133.9 P4 1 1/4" M10 58.72 30.17 P3 1" M10 52.37 26.19 500 3100 250 333 9112 388
0280 28.0 69.2 82.4 136.9 P4 1 1/4" M10 58.72 30.17 P3 1" M10 52.37 26.19 500 3100 250 333 9111 669 333 9112 274
0330 33.0 71.7 87.5 142.0 P4 1 1/4" M10 58.72 30.17 P3 1" M10 52.37 26.19 500 3000 250 333 9112 374
0380 38.0 74.3 92.5 147.0 P4 1 1/4" M10 58.72 30.17 P3 1" M10 52.37 26.19 500 3000 250 333 9111 290 333 9112 412
0440 44.0 77.3 98.6 153.1 P4 1 1/4" M10 58.72 30.17 P3 1" M10 52.37 26.19 500 2800 225 333 9111 150 333 9112 346
0520 52.0 81.3 106.7 161.2 P5 1 1/2" M12 69.82 35.71 P3 1" M10 52.37 26.19 500 2700 190 333 9111 360 333 9112 357
0700 70.0 90.4 124.9 179.4 P5 1 1/2" M12 69.82 35.71 P3 1" M10 52.37 26.19 500 2300 165 333 9111 563
E
41.2 C 175
28.0 B 73.0
9.4 H
Ød
60.3
Ø101.6 -0.05
21.1
130
W
12.7 G 2 x Ø14.3
A 146.0
Inlet
43.6
33.3 full spline
55
30°
Ø27.0
55
SAE “B” spline

13 teeth 16/32 DP
Outlet

Hydraulics Group
PGP517 A XXXX Y T1 D7 N SS PP B1 B1 “Y” = C (clockwise rotation)

0140 14.0 62.1 68.3 122.8 L3 27 51 M10 L2 19 40 M8 500 3400 250 333 9111 503
0160 16.0 63.2 70.3 124.8 L3 27 51 M10 L2 19 40 M8 500 3400 250 333 9111 505 333 9112 430
0190 19.0 64.7 73.3 127.8 L3 27 51 M10 L2 19 40 M8 500 3300 250 333 9111 285 333 9112 212
0230 23.0 66.7 77.4 131.9 L3 27 51 M10 L2 19 40 M8 500 3300 250 333 9111 119 333 9112 213
0250 25.0 67.7 79.4 133.9 L3 27 51 M10 L2 19 40 M8 500 3100 250 333 9111 047 333 9112 068
0280 28.0 69.2 82.4 136.9 L3 27 51 M10 L2 19 40 M8 500 3100 250 333 9111 287 333 9112 214
0330 33.0 71.7 87.5 142.0 L3 27 51 M10 L2 19 40 M8 500 2600 250 333 9111 014 333 9112 035
0380 38.0 74.3 92.5 147.0 L3 27 51 M10 L2 19 40 M8 500 2300 250 333 9111 015 333 9112 036
0440 44.0 77.3 98.6 153.1 L3 27 51 M10 L2 19 40 M8 500 2000 220 333 9111 046 333 9112 040
0520 52.0 81.3 106.7 161.2 L3 27 51 M10 L2 19 40 M8 500 1700 200 333 9111 242 333 9112 215
4
E
46.5 C 122
28.0 B 98.4
5.0 ØD 49.2
Ød
52
42.9
128.2
130
147
21.1
-0.03
-0.06
Ø50.8
24.0 G
4 x Ø11
A
Inlet
35.3
Woodruff key
M14 x 1.5
4x7.5-DIN 6888 20.8

1.7
55
4
Ø21.59
55
Installation torque Taper 1:8

50 +10 Nm Outlet

Hydraulics Group
Ordering Example Series PGP500
Code for multiple units
PGP 511 B 0160 C S2 D3 N L2 L1 S –
see single unit Rotation Flange code Inlet side port
Displacement Shaft code Shaft seal Outlet side

front unit port
Product type Section connection
B = Multiple pump S = Separate inlets

N = Multiple distributor pump C = Common inlet
(only for PGP505, PGP511 and PGP517) (For common inlet, the other (second)
inlet port must be coded B1.)
511 A 0110 X L2 L1 B1 B1
Product type 1) Shaft seal Outlet side Outlet rear

between sect. port port
Displacement Inlet side Inlet rear port

port
1)
Further B possible for triple units
Shaft seal between sect.
X = No seal
N = NBR (only for separate inlets)
This coding system can be used for all pumps series 500.

Hydraulics Group
Split Gear Pumps Series PGP500
Quality pays
Aluminium bodied ’split-gear‘ gear pumps are designed The flow pulsation is considerably decreased by phased
for high pressure and speed ratings together with high dual element gear sets, resulting in models with clearly
efficiency and optimised noise levels. lower noise levels. Common inlet available for multiple
section units.
Series PGP511 (on request)

s 5PTOBARCONSTANTOPERATIONPOSSIBLEDUETO
high-quality materials
s ,OWNOISELEVELSEVENINCONSTANTOPERATION
s (IGHEFlCIENCYTHANKSTOPRECISEMANUFACTURING
s #OMPLETEPRODUCTRANGEFORHUGEVARIETYOF
applications
s #OMMONINLETPORTSFORDOUBLEANDTRIPLEPUMPS
s 7IDECHOICEOFINTEGRATEDVALVESEGLOAD SENSING
and solenoid types
4
s &ULLRANGEOFPROVENMOTORSAVAILABLE

Hydraulics Group
Nomograph Series PGP500
Nomograph for Pipe Velocity
Flow Inside Pipe Diameter Flow Velocity

Q [l/min] d [mm/inch] v [m/s]
1000 0.10
900
800
700
0.15
600
500 0.20
400
0.30
300 Maximun recommended
velocity for 0.40
200 0.50
0.60
150 70
2.50 0.70
60 0.80
50 2.00 0.90
100 1.00
90 40
80 1.50 1.20
70 1.25 HFB, HFC 1.50
30
60 Inlet
1.00
50 2.00
20 Oil
40 0.75 2.50
Tank Return
15 3.00
30 HFB, HFC
0.50
4.00
Outlet
10
20 5.00
Oil 6.00
15 7.00
8.00
9.00
10 10.00
9
8
7 15.00
6
5 20.00
4
30.00
3 400 Q [l/min]
d [mm] =
6 v [m/s] 40.00
2 50.00

Hydraulics Group
Shaft Loads / Fluids Series PGP500
Shaft loads PGP500

Shaft
Code
loads PGP/PGM500
Description Type Torque rating [Nm]
PGP502 PGP505 PGP511 PGP517
H1 Ø10.0, 3.0 key, no thread, 36L parallel 30 — — —
P2 Ø9.95, 8.8L, 2.4 key, M6 taper 1:8 30 — — —
V1 5 x 6.5 long shaft w/o coupling tang drive 20 — — —
V2 5 x 4.5 short shaft w/o coupling tang drive 20 — — —
A1 9T, 16/32DP, 32L, SAE ”A” splined — 108 — —
J1 Ø12.7, 3.2 key, no thread, 38L parallel — 43 — —
K1 Ø15.88, 4.0 key, no thread, 32L, SAE ”A” parallel — 85 — —
Q2 Ø14.25, 5.5L, 3.0 key, M10x1 taper 1:8 — 68 — —
A1 9T, 16/32DP, 32L, SAE ”A” splined — — 86 —
C1 11T, 16/32DP, 38.2L, SAE 19-4 splined — — 184 —
F1 9T, B17x14.23L, DIN 5482 splined — — 101 —
K1 Ø15.88, 4.0 key, no thread, 32L, SAE ”A” parallel — — 75 —
L6 Ø19.05, 4.8 key, no thread, 32L, SAE 19-1 parallel — — 145 —
S1 Ø17.0, 7.7L, 3.0 key, M12x1.5 taper 1:5 — — 193 — 4
S2 Ø16.65, 12.0L, 3.2 key, M12x1.5 taper 1:8 — — 198 —
S4 Ø16.65, 12.0L, 4.0 key, M12x1.5 taper 1:8 — — 198 —
D1 13T, 16/32DP, 41.2L, SAE ”B” splined — — — 345
M1 Ø22.2, 6.3 key, no thread, 41.2L, SAE ”B” parallel — — — 251
M2 Ø25.4, 6.3 key, no thread, 46L, SAE ”B-B” parallel — — — 395
T1 Ø21.59, 11.2L, 4.0 key, M14x1.5 taper 1:8 — — — 250
Connecting shaft for multiple units 20 36 110 228
Formula to calculate shaft load
Hydraulic fluids
Type Fluid composition Max. working pressure [bar] Max. speed [min-1] Temperature Seal
Hydraulic fluid Mineral oil based on See Technical Data See Technical Data -15 ... +80 °C NBR
hydraulic fluid acc. to ISO/DIN -15 ... +120 °C FPM
HFB Water-in-oil emulsion 40/60 140 1500 +2 ... +65 °C NBR
HFC Water-glycol 40/60 140 1500 -15 ... +65 °C NBR
HFD Phosphate ester 140 1500 -10 ... +80 °C FPM
Flanges for suction and discharge ports

Please refer to Parker Bulletin 4040/UK.

Hydraulics Group
aerospace
climate control
Gear Pumps electromechanical
filtration
Series PGP fluid & gas handling
hydraulics
Fixed Displacement Pumps, pneumatics
Cast-Iron Designs process control
sealing & shielding
Catalogue HY02-8001/UK Cast-Iron Body Gear Pumps
Contents Series PGP600
Contents Page 4-2-

PGP600 Characteristics .................................................................................. 3
PGP/PGM620 Ordering Code .............................................................. 4
PGP620 Performance Curves .............................................................. 5
PGP/PGM640 Ordering Code .............................................................. 8
PGP640 Performance Curves .............................................................. 9
PGP600 Ordering Example (Multiple Pumps).................................... 11
Split Gear Pumps .......................................................................................... 12
Nomograph .................................................................................................... 13
Nomograph for Pipe Velocity ......................................................................... 13
Shaft Loads / Fluids ....................................................................................... 14

Hydraulics Group
Characteristics Series PGP600
Over many years Parker Hydraulics has supplied gear

pumps and motors for mobile and industrial markets
worldwide, especially for materials handling, commercial
grass cutting and construction equipment applications.
Many Parker pumps and motors have been developed
and tested for the specific needs of these industries.
Parker’s defined strategy to provide engineered solutions,

coupled with an award winning flexible manufacturing sys-
tem, has resulted in a wide range of SAE/DIN/European
and other special options being available as standard.
Features
s 0ATENTEDINTERLOCKINGBODYDESIGN s 0RESSUREBALANCEDDESIGNFORHIGHEFlCIENCY
s TOOTHGEARSBRONZEBALANCEPLATES s 2EDUCED SYSTEM NOISE LEVELS COMPARED TO EARLIER
s 4ANDEMTRIPLEANDCROSS FRAMEPUMPSAVAILABLE models 4
s #OMMON INLETS AVAILABLE FOR TANDEM AND TRIPLE s (IGHPOWERTHROUGH DRIVECAPABILITY
pumps s 7IDERANGEOFINTEGRALVALVESFORPOWERSTEERINGPOWER
s #ONTINUOUSOPERATINGPRESSURESUPTOBAR brakes, fan drivers and implement hydraulics
s 0RODUCTIONRUN INAVAILABLETOSUITE/%-APPLICATION s ,OADSENSEANDSOLENOIDOPERATEDUNLOADINGVALVES
CONDITIONS AND TO PROVIDE OPTIMIZED VOLUMETRIC s ,OWNOISEVERSIONAShSTEALTHhPUMP
efficiencies
Technical data
Pump type Heavy-duty, cast iron, external gear. Fluid viscosity Range of operating viscosity
Mounting SAE, rectangular, thru-bolt standard 8 to 1000 mm²/s.
specials on request. Max. permissible operating pressure
dependent on viscosity.
Ports SAE and metric split flanges and others
Shaft style SAE splined, keyed, tapered, cylindrical Viscosity range for cold start
tang drive, specials on request. 1000 to 2000 mm²/s at
operating pressure pa10 bar and
Speed 500 - 3500 rpm, see Technical Data speed n a1500 rpm.
Theor. displacement See Technical Data Range of ambient
Drive Drive direct with flexible coupling is temperature -40 °C to +70 °C
recommended. Filtration According to ISO 4406 Cl. 18/16/13
Axial / Radial load Units subject to axial or radial loads Direction of rotation Clockwise, counter-clockwise or double.
must be specified with an outboard (looking at the Attention! Drive pump only in
bearing. drive shaft) indicated direction of rotation.
Inlet pressure Operating range 0.8 to 2 bar abs. -ULTIPLEPUMP s!VAILABLEINTWOORTHREESECTION
Min. inlet pressure 0.5 bar abs. Short time assemblies configuration.
without load. Consultation is recommended. s-AXSHAFTLOADMUSTBECONFORMTO
Outlet pressure See Technical Data the limitations shown in the shaft loading
rating table in this catalogue.
Pressure rising rate Max. 3000 bar/s s-AXLOADISDETERMINEDBYADDING
Flow velocity See Nomograph for Pipe Velocity the torque values for each pumping
section that will be simultaneously
Hydraulic fluids Hydraulic oil HLP, DIN 51524-2 loaded.
Separate or common Separate inlet configuration:
Fluid temperature Range of operating temperature INLETCAPABILITY s%ACHGEARHOUSINGHASINDIVIDUALINLET
-15 to +80 °C. and outlet ports.
Max. permissible operating pressure Common inlet configuration:
dependent on fluid temperature. s4WOGEARSETSSHAREACOMMONINLET
Temperature for cold start -20 to -15 °C
at speed a 1500 rpm.
dependent on fluid temperature.

Hydraulics Group
PG 620 B 1 B 1
design place- seal side ports (rear ports on request)
ment option

P Pump
M Motor 1"-11 BSP thread/
E6E5 3/4"-14 BSP thread
1¼"-11 BSP thread/
Unit E7E5 3/4"-14 BSP thread
Code
Pump rec. from 29 ccm to 41 ccm
1½"-11 BSP thread/
A Single unit E8E6 1"-11 BSP thread/
B Multiple unit 1"-M10 SAE metric flange
T3T2 3/4"-M10 SAE metric flange
1¼"-M10 SAE metric flange
T4T3 1"-M10 SAE metric flange
1½"-M12 SAE metric flange
Displacement T5T3 1"-M10 SAE metric flange
Code ccm rec. from 41 ccm to 52 ccm
0160 16.0
0190 19.0
0210 21.0 Example: T4 = inlet port
0230 23.0 T3 = outlet port
0260 26.0
0290 29.0
0330 33.0
0360 36.0
0370 37.0
0410 41.0 Code Shaft seal
0440 44.0
0460 46.0 X No seal
0500 50.0 N NBR
0520 52.0 V FPM
Code Rotation
C Clockwise
A Counter- clock- Code Flange
wise
B Bi-directional 98.4x128.2 - Ø50.77
D7
rectangular
106.4 - Ø82.55 SAE ”A”
H2
2bolt flange
Code Shaft 146.1 - Ø101.06 SAE ”B”
H3
2bolt flange
2) 13T, 16/32DP, 41.2L,
D1 114.5 x 114.5 - Ø127 SAE ”C”
SAE ”B” spline A4 4bolt square
15T, 16/32DP, 46L,
E1
3!%h" "vSPLINE
Ø21.59, 11.2L, 4.0key,
T1 3)
M14x1.5, taper 1:8
2)
3)

Hydraulics Group
Performance Curves Series PGP620
PGP620 - 16.0 CC PGP620 - 26.0 CC
Flow [l/min.]
Flow [l/min.]
)NPUT0OWER;K7=
)NPUT0OWER;K7=
65 130
30 60
60 120
Flow at n=3500 rpm
28 56
55 110
26 52
50 100
24 48
Flow at n=3500 rpm
22 44 45 90
20 40 40 80
18 36
35 70
16 32
30 60
14 28 I. Power at n=3500 rpm
25 50
10 20 20 40 Flow at n=1500 rpm 4

8 16 15 30
6 12
4 8 Flow at n=500 rpm Flow at n=500 rpm
5 10
2 4
0 0
0 0 0 50 100 150 200 250 300
0 50 100 150 200 250 300
PGP620 - 41.0 CC PGP620 - 52.0 CC

Flow [l/min.]
)NPUT0OWER;K7=
80 160 80 160
Flow [l/min.]
)NPUT0OWER;K7=
75 150 75 150
70 140 70 140
65 130 65 130
60 120 60 120
55 110 55 110
50 100 50 100
45 90 45 90
40 80 40 80
Flow at n=1500 rpm
35 70 35 70
30 60 Flow at n=1500 rpm 30 60
25 50 25 50
20 40 20 40
15 30 15 30
Flow at n=500 rpm
10 20 Flow at n=500 rpm 10 20
5 10 5 10
0 0 0 0
0 50 100 150 200 250 300 0 50 100 150 200 250 300
Fluid temperature: 45 °C± 2K ; Viscosity: 36mm2/s ; Inlet pressure: 0.9 + 0.1 bar absolute

Hydraulics Group
PGP620 A XXXX Y D1 H3 N SS PP B1 B1 h9v #CLOCKWISEROTATION

XXXX cm3/rev A B SS G PP G min. rpm max. rpm max. bar clockwise counter-clockwise
0160 16.0 79.2 122.7 E6 1"-11 E5 ¾"-14 500 3000 275 702 9111 052 702 9112 053
0190 19.0 82.5 126.0 E6 1"-11 E5 ¾"-14 500 3000 275 702 9111 186
0210 21.0 84.7 128.2 E6 1"-11 E5 ¾"-14 500 3000 275 702 9111 168
0230 23.0 86.9 130.4 E6 1"-11 E5 ¾"-14 500 2700 275 702 9111 098 702 9112 054
0260 26.0 90.2 133.7 E6 1"-11 E5 ¾"-14 500 2400 275 702 9111 112 702 9112 093
0290 29.0 93.5 137.0 E7 1¼"-11 E5 ¾"-14 500 3000 275
0330 33.0 97.9 141.4 E7 1¼"-11 E5 ¾"-14 500 3000 275
0360 36.0 101.2 144.7 E7 1¼"-11 E5 ¾"-14 500 2900 250
0370 37.0 102.3 145.8 E7 1¼"-11 E5 ¾"-14 500 2900 250 702 9111 164 702 9112 046
0410 41.0 106.7 150.2 E7 1¼"-11 E5 ¾"-14 500 2600 220 702 9112 071
0440 44.0 110.0 153.5 E8 1½"-11 E6 1"-11 500 3000 210 702 9112 105
0460 46.0 112.2 155.7 E8 1½"-11 E6 1"-11 500 3000 210
0500 50.0 116.6 160.1 E8 1½"-11 E6 1"-11 500 3000 210
0520 52.0 118.8 162.3 E8 1½"-11 E6 1"-11 500 3000 210 702 9112 104
Dimensions (clockwise rotation shown) E
41.2 B 176
55.8 73.0
5.1 G
60.5
Ø101.6 -0.05
142
20.3
14.0 2 x Ø14.3
A 146.0
Inlet
33.3
25.7
.
67.0
Ø18.3
67.0
.
3!%h"vSPLINE
13 teeth 16/32 DP
Outlet flat root side fit

Hydraulics Group

XXXX cm3/ A B SS d G H W SS d G H W min. max. max. clockwise counter-
rev rpm rpm bar clockw.
0160 16 79.2 122.7 T3 1" M10 52.37 26.19 T2 ¾" M10 47.63 22.23 500 1500 275
0190 19 82.5 126.0 T3 1" M10 52.37 26.19 T2 ¾" M10 47.63 22.23 500 2300 275 702 9112 062
0210 21 84.7 128.2 T3 1" M10 52.37 26.19 T2 ¾" M10 47.63 22.23 500 2000 275
0230 23 86.9 130.4 T3 1" M10 52.37 26.19 T2 ¾" M10 47.63 22.23 500 1900 275
0260 26 90.2 133.7 T4 1¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 1600 275
0290 29 93.5 137.0 T4 1¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 3000 275 702 9111 151
0330 33 97.9 141.4 T4 1¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 2600 275 702 9111 087 702 9112 070
0360 36 101.2 144.7 T4 1¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 2400 250
0370 37 102.3 145.8 T4 1¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 2300 250
0410 41 106.7 150.2 T5 1½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 2100 220 702 9111 179 702 9112 117
0440 44 110.0 153.5 T5 1½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 2000 210 702 9112 037
0460 46 112.2 155.7 T5 1½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 1900 210 702 9111 117
0500
0520
50
52
116.6
118.8
160.1
162.3
T5
T5
1½"
1½"
M12
M12
69.82
69.82
35.71
35.71
T3
T3
1"
1"
M10
M10
52.37
52.37
26.19
26.19
500
500
1700
1700
210
210
702 9111 150
702 9112 022
4
E
41.2 B 176
55.8 73.0
5.1 W
60.5
20.3
Ø101.6 -0.05
142
H
Ød
14.0 G 2 x Ø14.3
A 146.0
Inlet
33.3
25.7
67.0
.
Ø18.3
67.0
.
3!%h"vSPLINE
13 teeth 16/32 DP
PI PGP-PGM UK.PMD RH Outlet

Hydraulics Group
PG 640 B 1 B 1
side ports
ment option
Code Type
P Pump
M Motor
Code Port options
1½" -11 BSP Thread /
E8E7 1¼" -11 BSP Thread
Unit rec. from 30 ccm to 50 ccm
Code
Pump 1¼" - M10 SAE metr. split flange
T4T3 h -3!%SPLITmANGE
A Single unit rec. from 30 ccm to 40 ccm
1½" - M12 SAE metr. split flange
B Multiple unit T5T3 h -3!%SPLITmANGE
2" - M12 SAE metr. split flange
T6T4 1¼" - M10 SAE metr. split flange
Example: T5 = inlet port

Displacement T3 = outlet port
Code ccm
0300 30.0
0350 35.0
0400 40.0
0450 45.0
0500 50.0
0550 55.0
0600 60.0
0650 65.0
0700 70.0 Code Shaft seal
0750 75.0 X No seal
0800 80.0 NBR
N
V FPM
T PTFE (motors only)
Code Rotation
C Clockwise
A Counter- clock-
wise
B Bi-directional
Code Flange
89.8x89.8 - Ø101.06
A3
Code Shaft 4 bolt square flange
13T, 16/32DP, 41.2L, A4 114.5x114.5 - Ø127 SAE ”C”
D1 2) 4 bolt square flange
SAE ”B” spline
15T, 16/32DP, 46.0L, H3 146.1 - Ø101.06 SAE ”B”
E1 2) 2 bolt flange
SAE ”B-B” spline
14T, 12/24DP, 55.6L, 181.0 - Ø127 SAE ”C”
E4 3) K3
SAE ”C” spline 2 bolt flange
2)
Only used with flange A3, H3.
3)
Only used with flange A4, K3.

Hydraulics Group
Performance Curves Series PGP640
PGP640 - 30.0 CC PGP640 - 50.0 CC

65 130 80 160
Flow [l/min.]
Flow [l/min.]
)NPUT0OWER;K7=
)NPUT0OWER;K7=

60 120
70 140
55 110
65 130
50 100
60 120
Flow at n=3000 rpm I. Power at n=3000 rpm
45 90 55 110
50
40 80 100
I. Power at n=3000 rpm 45
90
35 70
40
80
Flow at n=1500 rpm
30 60 35
70
25 50 30 60
Flow at n=1500 rpm
25
20 40
20
50
40
I. Power at n=1500 rpm 4
15 30
5 10
5 10
0 0 0 0
0 50 100 150 200 250 300 0 50 100 150 200 250 300
PGP640 - 65.0 CC PGP640 - 80.0 CC

130 260 260
Flow [l/min.]
130
)NPUT0OWER;K7=
Flow [l/min.]
)NPUT0OWER;K7=
Flow at n=3000 rpm

120 240 120 240
110 220 110 220
100 200 Flow at n=3000 rpm 100 200
90 180 90 180
80 160 80 160
70 140 70 140
60 120 60 120 Flow at n=1500 rpm
50 100 Flow at n=1500 rpm 50 100
40 80 40 80

30 60
10 20 20
10
0 0 0
0 50 100 150 200 250 300 0
0 50 100 150 200 250 300
Fluid temperature: 45 °C± 2K ; Viscosity: 36mm2/s ; Inlet pressure: 0.9 + 0.1 bar absolute

Hydraulics Group

XXXX cm3/ A B SS d G H W PP d G H W min. max. max. clockwise counter-
rev rpm rpm bar clockwise
0300 30 128.6 176.1 T4 1-¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 3000 310
0350 35 128.6 176.1 T4 1-¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 3000 310
0400 40 131.8 182.7 T4 1-¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 3000 310 704 9111 055 704 9112 020
0450 45 131.8 182.7 T5 1-½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 3000 310
0500 50 135.6 189.3 T5 1-½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 3000 310 704 9111 016
0550 55 135.6 189.3 T5 1-½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 3000 310 704 9111 050 704 9112 019
0600 60 138.4 195.8 T5 1-½” M12 69.82 35.71 T3 1" M10 52.37 26.19 500 3000 290 704 9111 059
0650 65 138.4 195.8 T6 2" M12 77.77 42.88 T4 1-¼" M10 58.72 30.17 500 3000 265 704 9111 040 704 9112 022
0700 70 142.2 203.2 T6 2" M12 77.77 42.88 T4 1-¼" M10 58.72 30.17 500 3000 245
0750 75 142.2 203.2 T6 2" M12 77.77 42.88 T4 1-¼" M10 58.72 30.17 500 3000 225
0800 80 142.2 203.2 T6 2" M12 77.77 42.88 T4 1-¼" M10 58.72 30.17 500 3000 210 704 9111 045

E
41.2 B 174
85.1 73.0
9.4 W
60
25.4
Ø101.6 -0.05
171
Ød
15.8 G 2 x Ø14.1
A 146.0
Inlet
42.6
33.3 full spline
80.0
80.0
3!%h"vSPLINE
13 teeth 16/32 DP
Outlet

Hydraulics Group
Ordering Example Series PGP600
Code for multiple units
PGP 620 B 0330 C D1 H3 N T4 T3 S –
see single unit Rotation Flange code Inlet side port
Displacement Shaft code Shaft seal Outlet side

front unit port
Product type Section connection
B = Multiple pump S = Separate inlets

N = Multiple distributor pump C = Common inlet
(For common inlet, the other (second)
4
inlet port must be coded B1.)
620 A 0260 X T4 T3 B1 B1
Product type 1) Shaft seal Outlet side Outlet rear

between sect. port port
Displacement Inlet side Inlet rear port

port
1)
Further B possible for triple units
This coding system can be used for all pumps series 600.

Hydraulics Group
Split Gear Pumps Series PGP600
Quality pays
Cast-iron bodied ’split-gear‘ gear pumps are designed The flow pulsation is considerably decreased by phased
for high pressure and speed ratings together with high dual element gear sets, resulting in models with clearly
efficiency and optimised noise levels. lower noise levels. Common inlet available for multiple
section units.
Series PGP620 (on request)

s 5PTOBARCONSTANTOPERATIONPOSSIBLEDUETO
high-quality materials
s ,OWNOISELEVELSEVENINCONSTANTOPERATION
s (IGHEFlCIENCYTHANKSTOPRECISEMANUFACTURING
s #OMPLETEPRODUCTRANGEFORHUGEVARIETYOF
applications
s #OMMONINLETPORTSFORDOUBLEANDTRIPLEPUMPS
s 7IDECHOICEOFINTEGRATEDVALVESEGLOAD SENSING
and solenoid types
s &ULLRANGEOFPROVENMOTORSAVAILABLE

Hydraulics Group
Nomograph Series PGP600
Nomograph for Pipe Velocity
Flow Inside Pipe Diameter Flow Velocity

Q [l/min] d [mm/inch] v [m/s]
1000 0.10
900
800
700
0.15
600
500 0.20
400
0.30
300 Maximun recommended
velocity for 0.40
200 0.50
4
0.60
150 70
2.50 0.70
60 0.80
50 2.00 0.90
100 1.00
90 40
80 1.50 1.20
70 1.25 HFB, HFC 1.50
30
60 Inlet
1.00
50 2.00
20 Oil
40 0.75 2.50
Tank Return
15 3.00
30 HFB, HFC
0.50
4.00
Outlet
10
20 5.00
Oil 6.00
15 7.00
8.00
9.00
10 10.00
9
8
7 15.00
6
5 20.00
4
30.00
3 400 Q [l/min]
d [mm] =
6 v [m/s] 40.00
2 50.00

Hydraulics Group
Shaft Loads / Fluids Series PGP600
Shaft loads PGP600

Code Description Type Torque rating 620 [Nm] Torque rating 640 [Nm]
D1 13T, 16/32 DP, 41.2L, SAE ”B” splined 272 328
E1 15T, 16/32 DP, 46.0L, SAE ”B-B” splined 460 503
E4 14T, 12/24 DP, 5.6L, SAE ”C” splined — 960
T1 Ø21.59, 11.2L, 4.0key, M14x1.5 tapered 1:8 218 —
Connecting shaft for multiple units 228 407
Formula to calculate shaft load
Hydraulic fluids
Type Fluid composition Max. working pressure [bar] Max. speed [min-1] Temperature Seal
Hydraulic fluid Mineral oil based on See Technical Data See Technical Data -15 ... +80 °C NBR
hydraulic fluid acc. to ISO/DIN -15 ... +120 °C FPM
(&" 7ATER IN OILEMULSION # ."2
(&# 7ATER GLYCOL # ."2
HFD Phosphate ester 140 1500 -10 ... +80 °C FPM
Flanges for suction and discharge ports

Please refer to Parker Bulletin 4040/UK.

Hydraulics Group
aerospace
climate control
Truck Hydraulics electromechanical
filtration
Series GPA and GP1 fluid & gas handling
hydraulics
Fixed Displacement Gear Pumps pneumatics
process control
sealing & shielding
Catalogue HY02-8001/UK Hydraulic Pumps, Fixed
Content Series GPA and GP1
Content Page 4-3-

General Information ................................................ 3
Light/medium duty gear pumps ........................... 3
Features .............................................................. 3
Dimensions, torque and flow diagrams................... 4
GPA-008/-012/-016/-019 3-bolt .......................... 4
GPA-008/-012/-016/-019 4-bolt .......................... 4
GP1-016/-019/-023/-029/-036/-041/-046 3-bolt ... 5
GP1-016/-019/-023/-029/-036/-041/-046 4-bolt ... 5
GP1-050/-060/-070/-080/-100 4-bolt .................. 6
Ordering Information............................................... 7
Conversion factors
1 bar ..............................................................14.5 psi
1 cm3 ........................................................0.061 cu in
1 kg ..................................................................2.20 lb
1 kW .............................................................. 1.34 hp
1 l .................................................... 0.264 US gallons
1 mm..............................................................0.039 in
1 N ................................................................0.225 lbf
1 Nm ..........................................................0.738 lbf ft
9/ °C + 32 ..............................................................°F
5
Catalogue HY30-8200/UK. 07/2008

Hydraulics Group
General Information Series GPA and GP1
Series GPA Series GP1

Light/medium duty gear pumps Features
Parker’s truck gear pumps are ideal for operators of s #OMPACTANDLIGHTWEIGHT EASYTOINSTALLEVENON
light trucks for their hydraulic power needs. small vehicles
The GPA/GP1 series gear pumps are available to suit
most applications. They are light and compact, and s 1UIETOPERATION LOWNOISEEMISSIONSAREIMPORTANT
in sensitive areas
can be installed in either rear or or side mount configu-
ration thanks to their unique dual port layout. 4
s 2OBUSTANDRELIABLE MEANSALONGTROUBLE FREE
The smaller GPA series is built with an extruded alumi- service life
num houising for minimum weight.
The larger GP1 pumps are built with compact cast iron s "UILTFORHIGHRPMS LESSSENSITIVETOOVER SPEEDING
housings for strength.
s "I DIRECTIONAL EASYTOINSTALL
The gear pumps complement our heavy duty piston
pumps and vane pumps.
s 3IDEORREARMOUNT USETHEPORTSONTHESIDEORAT
The performance and characteristics are ideal for many the rear, whichever is most suitable for the applica-
light and/or intermittent applications, including the tion.
famous Parker reliability, and they are engineered with
a long, trouble-free service life.
Series GPA characteristics (aluminum body; 3- and 4-bolt)

Frame size 008 012 016 019
Displacement [cm3/rev] 8 12 16 19
Max continuous pressure [bar] 250 250 250 230
Max intermittent pressure [bar] 270 270 270 250
Max peak pressure [bar] 290 290 290 270
Speed [rpm] (at max con-
tinuous pressure) min 500 500
max 2 000 2000
Weight [kg] 4.6 4.8 5.1 5.3
Series GP1 characteristics (cast iron body; 3- and 4-bolt)
Frame size 016 019 023 029 036 041 046 050 060 070 080 100
Displacement [cm3/rev] 16 19 23 29 36 41 46 50 60 70 80 100
Max continuous pressure [bar] 270 260 250 240 230 210 200 300 280 240 200 170
Max intermittent pressure [bar] 300 300 300 290 270 260 250 310 290 250 210 180
Max peak pressure [bar] 300 300 300 290 270 260 250 320 300 260 220 190
Speed [rpm] (at max con-
tinuous pressure) min 500 500
max 2000 2 000 1800 1700 1600 1400
Weight [kg] 6.0 6.3 6.7 7.1 7.5 7.8 8.1 12.5 13.0 13.5 14.0 15.0

Hydraulics Group
Dimensions Series GPA and GP1
GPA-008/-012/-016/-019 3-bolt
3PLINE"XX
ISO 14 / DIN 5462
50 E142
100 113
Ø52
16
"30
(14 deep; "30 Ø11 (x3)
38.4 shown plugged) B both sides Ø120
(14 deep)
78.5
3 A 7
Frame size 008 012 016 019

Dim. “A” 147 153 159 163
$IMh"v
GPA-008/-012/-016/-019 4-bolt
3PLINE"XX
ISO 14 / DIN 5462
50
100
16 120
80 C/186
"30
both sides Ø13 (x4)
38 9 12 80
(14 deep)
78.5 "30 55 B 108
(14 deep;
shown A 7
plugged)
Frame size 008 012 016 019
Dim. “A” 117 123 129 133
$IMh"v
Torque [Nm] Flow [l/min]

100 50
19 cm3/rev 19 cm3/rev
80 40
16
16
60 12 30
12
40 8 20
8
20 10
0 0
0 100 200 300 Pressure [bar] 0 1000 2000 Speed [rpm]
Diagrams reflect theoretical values Fluid temperature: -25 °C to +80 °C

$IRECTIONOFROTATION "I DIRECTIONAL 2ECOMMENDEDVISCOSITY TOMM2/s (cSt)
Input pressure: 0.7 to 3.0 bar (absolute) Max viscocity: 750 mm2/s (cSt)

Hydraulics Group
GP1-016/-019/-023/-029/-036/-041/-046 3-bolt
3PLINE"XX
ISO 14 / DIN 5462 57
78
C/220
114 123
19
Ø56
"30 "30 Ø11 (x3)

53.5 (16 deep; 3 12 both sides Ø72
shown plugged) (16 deep)
108 B 84
A 5
Frame size 016 019 023 029 036 041 046

Dim. “A” 156 160 166 171 181 188 196
$IMh"v
4
GP1-016/-019/-023/-029/-036/-041/-046 4-bolt
3PLINE"XX
ISO 14 / DIN 5462
57
78
114 129
19
Ø80
"30
53.5 "30 both sides
(16 deep; 9 12 Ø13 (x4) 80
(16 deep)
shown plugged) 55 B 106
108
A 5
Frame size 016 019 023 029 036 041 046

Dim. “A” 121 125 131 136 146 153 161
$IMh"v

200 100
46 cm3/rev 46 cm3/rev
41
160 80 41
36 36
29
120 60 29
23
19 23
80 16 40 19
16
40 20
0 0


Hydraulics Group
GP1-050/-060/-070/-080/-100 4-bolt
3PLINE"XX
ISO 14 / DIN 5462
73
146
25 152
Ø80
"30
"30 9 12 both sides Ø13 (x4)
78 80
(shown plugged)
135 55 B 108
A 5
Frame size 050 060 070 080 100

Dim. “A” 167 174 180 187 200
$IMh"v

400 200
100 cm3/rev 80 70 60
150 100 cm3/rev
300 80
50 70
60
200 100 50
100 50
0 0


Hydraulics Group
Ordering Information Series GPA and GP1
Product Code Part numbers Product Code Part numbers

Aluminium GPA-008-3 334 9113 921 Cast iron GP1-016-3 702 9113 921
3 bolt GPA-012-3 334 9113 922 3 bolt GP1-019-3 702 9113 922
GPA-016-3 334 9113 923 GP1-023-3 702 9113 923
GPA-019-3 334 9113 924 GP1-029-3 702 9113 924
GP1-036-3 702 9113 925
Product Code Part numbers GP1-041-3 702 9113 926
Aluminium GPA-008-4 334 9113 911 GP1-046-3 702 9113 927
4 bolt GPA-012-4 334 9113 912
GPA-016-4 334 9113 913 Product Code Part numbers
GPA-019-4 334 9113 914 Cast iron GP1-016-4 702 9113 911
4 bolt GP1-019-4 702 9113 912
GP1-023-4 702 9113 913
GP1-029-4 702 9113 914 4
GP1-036-4 702 9113 915
GP1-041-4 702 9113 916
GP1-046-4 702 9113 917
GP1-050-4 704 9113 911
GP1-060-4 704 9113 912
GP1-070-4 704 9113 913
GP1-080-4 704 9113 914
GP1-100-4 704 9113 915

Hydraulics Group

Gear Pumps

Uploaded by

Copyright:

Available Formats

Gear Pumps

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Gear Pumps

Uploaded by

Copyright:

Available Formats

aerospace

Contents Page 4-1-

4-1- 2 Parker Hanniﬁn Corporation

PGP 500 pumps offer superior performance, high efﬁ-

4-1- 3 Parker Hanniﬁn Corporation

Code Type Code Port options

H1 2) Ø10, 3.0 key, no thread, 36L,

4-1- 4 Parker Hanniﬁn Corporation

PGP502 - 0.8 CC PGP502 - 2.1 CC

Input Power [kW]

1.4 2.8 3.5 7.0

I. Power at n=4000 rpm

I. Power at n=4000 rpm

0.8 1.6 2.0 4.0

0.6 1.2 Flow at n=1500 rpm 1.5 3.0

Flow at n=500 rpm Flow at n=500 rpm

I. Power at n=500 rpm I. Power at n=500 rpm

Input Power [kW]

7.5 15 Flow at n=3000 rpm

6.5 13 8.0 16.0

5.5 11 7.0 14.0

5.0 10 I. Power at n=3000 rpm

4-1- 5 Parker Hanniﬁn Corporation

PGP502 A XXXX Y P2 D1 N SS PP B1 B1 “Y” = C (clockwise rotation)

Dimensions (clockwise rotation shown)

4-1- 6 Parker Hanniﬁn Corporation

Code Type Code Port options

A Single unit Example: J7 = inlet port

9T, 16/32DP, 32L, SAE ”A”

4-1- 7 Parker Hanniﬁn Corporation

PGP505 - 3.0 CC PGP505 - 6.0 CC

Input Power [kW]

6.0 12 Flow at n=4000 rpm 12 24

5.5 11 11 22 Flow at n=3600 rpm

4.5 9.0 9.0 18

4.0 8.0 8.0 16

3.0 6.0 6.0 12

1.5 3.0 3.0 6.0

Input Power [kW]

3.0 6.0 3.0 6.0 Flow at n=500 rpm

1.0 2.0 1.0 2.0

4-1- 8 Parker Hanniﬁn Corporation

PGP505 A XXXX Y A1 H2 N SS PP B1 B1 “Y” = C (clockwise rotation)

Dimensions (clockwise rotation shown)

SAE “A” spline

4-1- 9 Parker Hanniﬁn Corporation

PGP505 A XXXX Y Q2 D2 N SS PP B1 B1 “Y” = C (clockwise rotation)

Dimensions (clockwise rotation shown)

4-1- 10 Parker Hanniﬁn Corporation

E5E3 3/4" - 14 BSP thread/

4-1- 11 Parker Hanniﬁn Corporation

Pressure depending on speed

4.0 TO 19.0 cc 4.0 TO 16.0 cc

Pressure depending on viscosity

Viscosity N [mm /s (cSt)]

4-1- 12 Parker Hanniﬁn Corporation

PGP511 - 6.0 CC PGP511 - 10.0 CC

Input Power [kW]

Input Power [kW]

PGP620 A XXXX Y D1 H3 N SS PP B1 B1 h9v #CLOCKWISEROTATION

PGP620 A XXXX Y D1 H3 N SS PP B1 B1 h9v #CLOCKWISEROTATION