DENISON HYDRAULICS

vane pumps - single, double, triple

T6 mobile application.

Publ. 1 - EN0701 - A 09 / 00 / 3000 / FB Replaces : 1 - EN 075 - D L13-10701-1

BACK TO THE TABLE OF CONTENT

 CONTENTS - T6 SERIES MOBILE APPLICATION

GENERAL Features ........................................................................................................................... 3

Instructions ..................................................................................................................... 3
Minimum & maximum speeds ....................................................................................... 4
Pressure ratings ............................................................................................................... 4
Priming at starting........................................................................................................... 4
Minimum allowable inlet pressure ................................................................................. 5
General characteristics.................................................................................................... 5
Pump selection : Routine and example .......................................................................... 6
Intermittent pressure rating............................................................................................. 6
Description...................................................................................................................... 7
Application advantages................................................................................................... 7
Shafts and hydraulic fluids ............................................................................................. 8
Notes ............................................................................................................................... 9

T6CM Ordering code & Technical data................................................................................... 10

Dimensions & Operating characteristics ...................................................................... 11

T6CP Ordering code & Technical data................................................................................... 12

Dimensions & Operating characteristics ...................................................................... 13

T6D* Ordering code & Technical data................................................................................... 14

Dimensions & Operating characteristics ...................................................................... 15

T6E* Ordering code & Technical data................................................................................... 16

Dimensions & Operating characteristics ...................................................................... 17

T6CC* Ordering code & Technical data................................................................................... 18

Dimensions & Operating characteristics ...................................................................... 19

T6DC* Ordering code & Technical data................................................................................... 20

Dimensions & Operating characteristics ...................................................................... 21

T6EC* Ordering code & Technical data................................................................................... 22

Dimensions & Operating characteristics ...................................................................... 23

T6ED* Ordering code & Technical data................................................................................... 24

Dimensions & Operating characteristics ...................................................................... 25

T6DCCM Ordering code & Operating characteristics ................................................................. 26

Dimensions ................................................................................................................... 27
Technical data ............................................................................................................... 28

T6EDC* Technical data ............................................................................................................... 29

Dimensions T6EDCM .................................................................................................. 30
Dimensions T6EDCS ................................................................................................... 31
Ordering code & Operating characteristics .................................................................. 32

Additional shafts ........................................................................................................... 33

Porting diagrams for double pumps ............................................................................. 34
Porting diagrams for triple pumps........................................................................ 34 - 35

BACK TO THE TABLE OF CONTENT

 FEATURES - T6 SERIES MOBILE APPLICATION

GREATER FLOW Greater flow for the envelope size is achieved by increased displacement cam rings : at
high permissible speeds with atmospheric inlet
C → 3 to 31 GPM, 10 to 100 ml/rev.
D → 14 to 50 GPM, 48 to 158 ml/rev.
E → 42 to 72 GPM, 132 to 227 ml/rev.

HIGHER PRESSURE Pressure ratings to 275 bar reduce size and cost of actuators, valves and lines, give
extended life at reduced pressures.

BETTER EFFICIENCY Better efficiency under load increases productivity, reduces heating and operating
costs.

MOUNTING FLEXIBILITY Up to 32 positions for double pumps and up to 128 for triple pumps: this reduces
mounting costs and improves performance.

LOWER NOISE LEVELS Increase operator safety and acceptance.

COMPLETE CONFORMITY To SAE - J744c 2-bolt standards and to ISO 3019-1 (T6EDCS SAE E, T6EDCM ISO
3019/2) in the various keyed and splined shaft options offered.

CARTRIDGE DESIGN Provides for drop-in assemblies. This allows easy conversion or renewal of serviceable
elements in minutes at minimum expense and risk of contamination. The "C" & "D"
cartridge pumps are birotational and indicated by "B" description in cartridge model
number. Pump rotation is easy to change by changing position of cam ring on port
plate dowel pin hole.

WIDER RANGE OF Viscosities from 2000 to 10 cSt permit colder starts and hotter running. The balanced
ACCEPTABLE VISCOSITIES design compensates for wear and temperature changes. At high viscosity or cold
temperature, the rotor to side plates gap is well lubricated and improves mechanical
efficiency.

FIRE RESISTANT FLUIDS Including phosphate esters, chlorinated hydrocarbons, water glycols and invert
emulsions may be pumped at higher pressures and with longer service life by these
pumps.

GENERAL APPLICATIONS 1. Check speed range, pressure, temperature, fluid quality, viscosity and pump rotation.
INSTRUCTIONS 2. Check inlet conditions of the pump, if it can accept application requirement.
3. Type of shaft : if it would support operating torque.
4. Coupling must be chosen to minimize pump shaft load (weight, misalignment).
5. Filtration : must be adequate for lowest contamination level.
6. Environment of pump : to avoid noise reflection, pollution and shocks.

BACK TO THE TABLE OF CONTENT

 MINIMUM & MAXIMUM SPEED, PRESSURE RATINGS - T6 SERIES MOBILE APPLICATION

Theoretical Maximum Speed Maximum Pressure

Displacement Minimum HF-0,HF-1 HF-3, HF-4 HF-0, HF-2 HF-1, HF-4, HF-5 HF-3
Size Series Vi Speed HF-2 HF-5 Int. Cont. Int. Cont. Int. Cont.
ml/rev. RPM RPM RPM bar bar bar bar bar bar
B03 10,8
B05 17,2
B06 21,3
B08 26,4
B10 34,1
CM B12 37,1 400 2800 1800 275 240 210 175 175 140
CP B14 46,0
B17 58,3
B20 63,8
B22 70,3
B25 79,3
B28 88,8 2500 210 160 160
B31 100,0
B14 47,6
B17 58,2
B20 66,0
B24 79,5
DM B28 89,7 400 2500 1800 240 210 210 175 175 140
DP B31 98,3
B35 111,0
B38 120,3
B42 136,0
B45 145,7 2200
B50 158,0 210 160 160
042 132,3
045 142,4
050 158,5
EM 400 2200 1800 240 210 210 175 175 140
EP 052 164,8
062 196,7
066 213,3
072 227,1

HF-0, HF2 = Antiwear Petroleum Base

HF-1 = Non Antiwear Petroleum Base
HF-5 = Synthetic Fluids
HF-3 = Water in oil Emulsions
HF-4 = Water Glycols

For further information or if the performance characteristics outlined above do not meet your own particular requirements, please
consult your local DENISON Hydraulics office.

PRIMING AT STARTING At first, start operation of the pump shaft at the lowest speed and at the lowest pressure
to obtain priming. When a pressure relief valve is used at the outlet, it should be
backed off to minimize return pressure.
When possible, an air bleed off should be provided in the circuit to facilitate purging of
system air.
Never operate pump shaft at top speed and pressure without checking for completion
of pump priming, and the fluid has no aeration disaerated.

BACK TO THE TABLE OF CONTENT

 MINIMUM ALLOWABLE INLET PRESSURE (BAR ABSOLUTE) - T6 SERIES MOBILE APPLICATION

Cartridge Speed RPM

Size Series 1200 1500 1800 2100 2200 2300 2500 2800 Series
B03 B03
B05 B05
B06 0,80 0,90 B06
0,80 1,00
B08 0,80 B08
B10 B10
CM B12 0,80 0,80 0,80 0,85 0,92 B12
CP B14 B14
B17 0,85 0,95 1,03 B17
B20 0,90 B20
B22 0,85 0,90 0,98 1,05 B22
B25 0,90 0,95 0,95 1,05 B25
B28 0,98 0,98 1,08 B28
B31 0,85 0,90 1,00 1,11 B31
B14 0,80 1,00 B14
B17 0,88 0,95 B17
B20 B20
B24 0,80 0,82 1,10 B25
DM B28 0,80 0,80 0,85 0,92 1,00 1,18 B28
DP B31 0,90 0,95 1,23 B31
B35 0,92 0,98 1,02 1,29 B35
B38 0,95 1,00 1,05 B38
B42 1,02 1,08 B42
B45 0,85 0,98 1,05 B45
B50 1,02 1,09 B50
042 0,88 042
045 045
050 0,80 0,80 0,80 0,90 1,00 050
EM
EP 052 052
062 0,85 0,95 062
066 0,85 0,85 0,95 1,00 1,09 066
072 0,85 1,05 072
Inlet pressure is measured at inlet flange with petroleum base fluids at viscosity between 10 and 65 cSt. The difference between inlet
pressure at the pump flange and atmospheric pressure must not exceed 0,2 bar to prevent aeration.
Multiply absolute pressure by 1,25 for HF-3, HF-4 fluids.
by 1,35 for HF-5 fluid.
by 1,10 for ester or rapeseed base.
Use highest cartridge absolute pressure for double & triple pump.
GENERAL CHARACTERISTICS
Mounting standard Weight without Moment of inertia SAE 4 bolts
connector and kgm2 x 10-4 J518c - ISO/DIS 6162-1 - 4) ISO/DIS 6162-2
bracket - kg Suction Pressure
T6CM SAE J744c 15,7 7,5 1"1/2 1"
ISO/3019-1 SAE B
T6CP 18,0 7,8 2" 4) 1"1/4 4)
T6D* SAE J744c 24,0 23,3 2" 1"1/4
T6E* ISO/3019-1 SAE C 43,3 51,5 3" 1"1/2
T6CC* SAE J744c 26,0 14,9 2"1/2 or P1 P2
ISO/3019-1 SAE B 3" 1" 1" or 3/4"
T6DC* 36,6 30,4 3" 1"1/4 1"
T6EC* SAE J744c 55,0 73,4 3"1/2 1"1/2 1"
T6ED* ISO/3019-1 SAE C 66,0 73,4 4" 1"1/2 1"1/4
T6DCC* 61,0 37,3 4" P1 P2 P3
1"1/4 1" 1" or 3/4"
T6EDC* SAE "E" (T6EDCS) 100,0 80,2 4" 1"1/2 1"1/4 1" or 3/4"
ISO/3019-2 (T6EDCM)

BACK TO THE TABLE OF CONTENT

 PUMP SELECTION - T6 SERIES MOBILE APPLICATION

CALCULATION To resolve Performances required

Volumetric displacement Vi [ml/rev.] Requested flow qv [l/min] 60
Available flow qv [l/min] Speed n [R.P.M.] 1500
Input power P [kW] Pressure p [bar] 150

ROUTINE AND EXAMPLE Routine : Example :

1000 Q 1000 x 60
1. First calculation Vi = Vi = = 40 ml/rev.
n 1500

2. Choice Vi of pump immediately T6CM B14 Vi = 46 ml/rev.

greater (see tabulation)

3. Theoretical flow of this pump 46 x 1500

qVI = = 69 l/min
Vp x n 1000
qVi =
1000

4. Find qVs leakage function of T6CM (page 10) : qVS = 5 l/min at

pressure qVs = f(p) on curve at 10 or 150 bar, 24 cSt
24 cSt

5. Available flow qVe = qVi - qVs qVe = 69 - 5 = 64 l/min

6. Theoretical input power 69 x 150

Pi = = 17,3 kW
qvi x p 600
Pi =
600

7. Find ps hydrodynamic power loss T6CM (page10) : Ps at 1500 R.P.M.,

on curve 150 bar = 1,5 kW

8. Calculation of necessary input P = 17,3 + 1,5 = 18,8 kW

power P = Pi + Ps

9. Results Vi = 46,0 ml/rev

qVe = 64,0 l/min T6CM B14
P = 18,8 kW

These calculation steps must be followed for each application.

INTERMITTENT PRESSURE T6 units may be operated intermittently at pressures higher than the recommended
RATING continuous rating when the time weighted average of pressure is less than or equal to
the continuous duty pressure rating.
This intermittent pressure rating calculation is only valid if other parameters; speed,
fluid, viscosity and contamination level are respected.
For total cycle time higher than 15 minutes, please consult your DENISON Hydraulics
representative.

Example : T6CM - B14

Duty cycle 4 min. at 275 bar
1 min. at 35 bar
5 min. at 160 bar

(4 x 275) + (1 x 35) + (5 x 160)

= 193,5 bar
10

193,5 bar is lower than 240 bar allowed as continuous pressure for T6CM - B14 with
HF-0 fluid.

BACK TO THE TABLE OF CONTENT

 DESCRIPTION - T6 SERIES MOBILE APPLICATION

Cap end outlet port has Inlet Shaft end outlet port has Outlet Inlet
8-positions at 45° intervals 4-positions at 90° intervals
relative to inlet on T6DC. relative to inlet. Front & rear sideplates are
each clamped axially by the
separate discharge pressures.

Pilot recess as required

by SAE for
full conformity.
Shaft comes in variety
of keyed and splined
options to meet SAE
and ISO 3019-1.

Ball bearing hold

shaft in alignment.
T6*P Front sideplate is clamped
Cartridges are replaceable double shaft seal Cartridge is replaceable
assemblies. Each includes axially by discharge assembly including cam
cam ring, rotor, vanes, pins pressure to reduce internal ring, rotor, vanes, pins
and sideplates. Drain hole leakage. and sideplate

Vane is urged outward at Holes in cam ring Working vane on

suction ramp by pin force 90° section improve wide cartridge major arc pushes fluid
and centrifugal force. inlet characteristics. to discharge port.

Suction ramp
where unloaded
vane moves out.

Section B-B
Pin cavity is at a steady
pressure slightly higher
than at discharge port.

Lub side holes lubricate Discharge ramp

Section A-A the sideplate surfaces. where unloaded
vane moves in. Working vane on minor arc
seals discharge pressure from
the suction port.

APPLICATION ADVANTAGES • The high pressure capability to 275 bar, in the small envelope, reduces installation
costs and provides extended life at reduced pressure.
• The high volumetric efficiency, typically 94%, reduces heat generation, and allows
speeds down to 400 RPM at full pressure.
• The high mechanical efficiency, typically 94%, reduces energy consumption.
• The wide speed range from 400 RPM to 2800 RPM, combined with large size
cartridge displacements, will optimize operation for the lowest noise level in the
smallest envelope.
• The low speed 400 RPM, low pressure, high viscosity 2000 cSt allow application
in cold environments with minimum energy consumption and without seizure risk.
• The low ripple pressure ± 2 bar reduces piping noise and increases life time of
other components in the circuit.
• The high resistance to particle contamination because of the double lip vane
increases pump life.
• The large variety of options (cam displacement, shaft, porting) allows customized
installation.
• The shaft option T (SAE J718c), allows direct drive (at 540 or 1000 RPM) on
tractors.
• The double shaft seal (T6*P version) and drain hole allow direct mounting onto
gear boxes.

BACK TO THE TABLE OF CONTENT

 ORDERING CODE - T6CP SERIES MOBILE APPLICATION

Model No. T6CP - B22 - 2 R 00 - A 1

Series P = Mobile 2 shaft seals Modification

Cam ring Seal class
(Delivery at 0 bar & 1500 r.p.m.) 1 = S1 (for mineral oil)
B14 = 69,0 l/min B25 = 118,9 l/min 4 = S4 (for the resistant fluids)
B17 = 87,4 l/min B28 = 133,2 l/min 5 = S5 (for mineral oil and fire
B20 = 95,7 l/min B31 = 150,0 l/min resistant fluids)
B22 = 105,4 l/min
Design letter
Type of shaft
2 = keyed (no SAE) Porting combination
3 = splined (SAE C) 00 = standard
Direct. of rotation (view on shaft end)
R = clockwise
L = counter-clockwise

P = Pressure port
S = Suction port

INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)

T6CP - B22

Lp. Noise level [db(A)] 1m ISO 4412

Internal leakage Qs [l/min]

Pressure p [bar] Pressure p [bar]

Do not operate the pump more than 5 seconds at any speed or
viscosity if internal leakage is more than 50% of theoretical flow.

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]

Load F [N]

Pressure p [bar] Speed n [RPM]

Maximum permissible axial load Fa = 800 N

12

BACK TO THE TABLE OF CONTENT

 DIMENSIONS & OPERATING CHARACTERISTICS - Weight : 18,0 kg - T6CP SERIES MOBILE APPLICATION

OPERATING CHARACTERISTICS - TYPICAL [24 cSt]

Series Volumetric Speed Flow Q [l/min] Input power P [kW]
Displacement Vp n [R.P.M.] p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
B14 46,0 ml/rev 1000 46,0 40,5 36,0 1,4 11,7 19,9
1500 69,0 63,5 59,0 1,9 17,6 29,5
B17 58,3 ml/rev 1000 58,3 52,8 48,3 1,6 14,5 24,8
1500 87,4 82,0 77,5 2,1 21,9 36,9
B20 63,8 ml/rev 1000 63,8 58,3 53,8 1,6 15,8 27,0
1500 95,7 90,2 85,7 2,2 23,8 40,2
B22 70,3 ml/rev 1000 70,3 64,8 60,3 1,7 17,3 29,6
1500 105,4 100,0 95,5 2,3 26,1 44,1
B251) 79,3 ml/rev 1000 79,3 73,8 69,3 1,8 19,3 33,2
1500 118,9 113,5 109,0 2,5 29,2 49,5
B281) 88,8 ml/rev 1000 88,8 83,3 80,12) 1,9 21,9 32,52)
1500 133,2 127,7 124,52) 2,8 32,7 48,52)
1)
B31 100,0 ml/rev 1000 100,0 94,5 91,32) 2,0 24,4 36,42)
1500 150,0 144,5 141,32) 2,8 36,5 54,42)
1) 2)
B25 - B28 - B31 = 2500 R.P.M. max. B28 - B31 = 210 bar max. int.

13

BACK TO THE TABLE OF CONTENT

 ORDERING CODE - T6D* SERIES MOBILE APPLICATION

Model No. T6D* - B45 - 1 R 00 - C 1

Series M = Mobile 1 shaft seal Modification

Series P = Mobile 2 shaft seals
Seal class
Cam ring 1 = S1 (for mineral oil)
(Delivery at 0 bar & 1500 r.p.m.) 4 = S4 (for the resistant fluids)
B14 = 71,4 l/min B35 = 166,5 l/min 5 = S5 (for mineral oil and fire
B17 = 87,3 l/min B38 = 180,4 l/min resistant fluids)
B20 = 99,0 l/min B42 = 204,0 l/min
B24 = 119,3 l/min B45 = 218,5 l/min Design letter
B28 = 134,5 l/min B50 = 237,0 l/min Porting combination
B31 = 147,4 l/min 00 = standard
Type of shaft Type of shaft Direct. of rotation (view on shaft end)
M version P version R = clockwise
1 = keyed (SAE C) L = counter-clockwise
2 = keyed (no SAE)
3 = splined (SAE C) 3 = splined (no SAE)
4 = splined (no SAE) P = Pressure port
T = splined (SAE J718c) S = Suction port

INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)

T6DM - B38

Lp. Noise level [db(A)] 1m ISO 4412

Internal leakage Qs [l/min]

Pressure p [bar] Pressure p [bar]

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]

Load F [N]

Pressure p [bar] Speed n [RPM]

Maximum permissible axial load Fa = 1200 N

14

BACK TO THE TABLE OF CONTENT

 DIMENSIONS & OPERATING CHARACTERISTICS - Weight : 24,0 kg - T6D* SERIES MOBILE APPLICATION

Additional T6DM shaft code T: see page 33 Shaft torque limits [ml/rev x bar]
Additional T6DP version shaft see page 33 Pump Shaft V x p max.
T6DM 2 34590
OPERATING CHARACTERISTICS - TYPICAL [24 cSt]
Series Volumetric Speed Flow Q [l/min] Input power P [kW]
Displacement Vp n [R.P.M.] p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
B14 47,6 ml/rev 1000 47,6 38,3 32,1 1,5 12,5 20,7
1500 71,4 62,1 55,9 2,3 18,5 30,6
B17 58,2 ml/rev 1000 58,2 48,9 42,7 1,6 14,9 24,9
1500 87,3 78,0 71,8 2,5 22,2 37,0
B20 66,0 ml/rev 1000 66,0 56,7 50,5 1,7 16,8 28,0
1500 99,0 89,7 83,5 2,8 24,9 41,7
B24 79,5 ml/rev 1000 79,5 70,2 64,0 1,9 19,9 33,4
1500 119,3 110,0 103,8 3,0 29,6 49,8
B28 89,7 ml/rev 1000 89,7 80,4 74,2 2,0 22,3 37,5
1500 134,5 125,2 119,0 3,2 33,2 55,9
B31 98,3 ml/rev 1000 98,3 89,0 82,8 2,1 24,3 40,9
1500 147,4 138,1 131,9 3,3 36,2 61,0
B35 111,0 ml/rev 1000 111,0 101,7 95,5 2,3 27,3 46,0
1500 166,5 157,2 151,0 3,5 40,7 68,7
B38 120,3 ml/rev 1000 120,3 111,0 104,8 2,4 29,4 49,8
1500 180,4 171,1 164,9 3,7 43,9 74,3
B421) 136,0 ml/rev 1000 136,0 126,7 120,5 2,6 33,1 56,0
1500 204,0 194,7 188,5 4,0 49,4 83,7
B451) 145,7 ml/rev 1000 145,7 136,4 130,2 2,7 35,3 59,9
1500 218,5 209,2 203,0 4,1 52,8 89,5
B501) 158,0 ml/rev 1000 158,0 148,7 145,02) 2,8 38,2 56,82)
1500 237,0 227,7 224,02) 4,4 57,0 85,02)
1) 2)
B42 - B45 - B50 = 2200 R.P.M. max. B50 = 210 bar max. int. Port connection can be furnished with metric threads.

15

BACK TO THE TABLE OF CONTENT

 ORDERING CODE - T6CP SERIES MOBILE APPLICATION

Model No. T6CP - B22 - 2 R 00 - A 1

Series P = Mobile 2 shaft seals Modification

Cam ring Seal class
(Delivery at 0 bar & 1500 r.p.m.) 1 = S1 (for mineral oil)
B14 = 69,0 l/min B25 = 118,9 l/min 4 = S4 (for the resistant fluids)
B17 = 87,4 l/min B28 = 133,2 l/min 5 = S5 (for mineral oil and fire
B20 = 95,7 l/min B31 = 150,0 l/min resistant fluids)
B22 = 105,4 l/min
Design letter
Type of shaft
2 = keyed (no SAE) Porting combination
3 = splined (SAE C) 00 = standard
Direct. of rotation (view on shaft end)
R = clockwise
L = counter-clockwise

P = Pressure port
S = Suction port

INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)

T6CP - B22

Lp. Noise level [db(A)] 1m ISO 4412

Internal leakage Qs [l/min]

Pressure p [bar] Pressure p [bar]

Do not operate the pump more than 5 seconds at any speed or
viscosity if internal leakage is more than 50% of theoretical flow.

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]

Load F [N]

Pressure p [bar] Speed n [RPM]

Maximum permissible axial load Fa = 800 N

12

BACK TO THE TABLE OF CONTENT

 DIMENSIONS & OPERATING CHARACTERISTICS - Weight : 18,0 kg - T6CP SERIES MOBILE APPLICATION

OPERATING CHARACTERISTICS - TYPICAL [24 cSt]

Series Volumetric Speed Flow Q [l/min] Input power P [kW]
Displacement Vp n [R.P.M.] p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
B14 46,0 ml/rev 1000 46,0 40,5 36,0 1,4 11,7 19,9
1500 69,0 63,5 59,0 1,9 17,6 29,5
B17 58,3 ml/rev 1000 58,3 52,8 48,3 1,6 14,5 24,8
1500 87,4 82,0 77,5 2,1 21,9 36,9
B20 63,8 ml/rev 1000 63,8 58,3 53,8 1,6 15,8 27,0
1500 95,7 90,2 85,7 2,2 23,8 40,2
B22 70,3 ml/rev 1000 70,3 64,8 60,3 1,7 17,3 29,6
1500 105,4 100,0 95,5 2,3 26,1 44,1
B251) 79,3 ml/rev 1000 79,3 73,8 69,3 1,8 19,3 33,2
1500 118,9 113,5 109,0 2,5 29,2 49,5
B281) 88,8 ml/rev 1000 88,8 83,3 80,12) 1,9 21,9 32,52)
1500 133,2 127,7 124,52) 2,8 32,7 48,52)
1)
B31 100,0 ml/rev 1000 100,0 94,5 91,32) 2,0 24,4 36,42)
1500 150,0 144,5 141,32) 2,8 36,5 54,42)
1) 2)
B25 - B28 - B31 = 2500 R.P.M. max. B28 - B31 = 210 bar max. int.

13

BACK TO THE TABLE OF CONTENT

 ORDERING CODE - T6D* SERIES MOBILE APPLICATION

Model No. T6D* - B45 - 1 R 00 - C 1

Series M = Mobile 1 shaft seal Modification

Series P = Mobile 2 shaft seals
Seal class
Cam ring 1 = S1 (for mineral oil)
(Delivery at 0 bar & 1500 r.p.m.) 4 = S4 (for the resistant fluids)
B14 = 71,4 l/min B35 = 166,5 l/min 5 = S5 (for mineral oil and fire
B17 = 87,3 l/min B38 = 180,4 l/min resistant fluids)
B20 = 99,0 l/min B42 = 204,0 l/min
B24 = 119,3 l/min B45 = 218,5 l/min Design letter
B28 = 134,5 l/min B50 = 237,0 l/min Porting combination
B31 = 147,4 l/min 00 = standard
Type of shaft Type of shaft Direct. of rotation (view on shaft end)
M version P version R = clockwise
1 = keyed (SAE C) L = counter-clockwise
2 = keyed (no SAE)
3 = splined (SAE C) 3 = splined (no SAE)
4 = splined (no SAE) P = Pressure port
T = splined (SAE J718c) S = Suction port

INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)

T6DM - B38

Lp. Noise level [db(A)] 1m ISO 4412

Internal leakage Qs [l/min]

Pressure p [bar] Pressure p [bar]

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]

Load F [N]

Pressure p [bar] Speed n [RPM]

Maximum permissible axial load Fa = 1200 N

14

BACK TO THE TABLE OF CONTENT

 DIMENSIONS & OPERATING CHARACTERISTICS - Weight : 24,0 kg - T6D* SERIES MOBILE APPLICATION

Additional T6DM shaft code T: see page 33 Shaft torque limits [ml/rev x bar]
Additional T6DP version shaft see page 33 Pump Shaft V x p max.
T6DM 2 34590
OPERATING CHARACTERISTICS - TYPICAL [24 cSt]
Series Volumetric Speed Flow Q [l/min] Input power P [kW]
Displacement Vp n [R.P.M.] p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
B14 47,6 ml/rev 1000 47,6 38,3 32,1 1,5 12,5 20,7
1500 71,4 62,1 55,9 2,3 18,5 30,6
B17 58,2 ml/rev 1000 58,2 48,9 42,7 1,6 14,9 24,9
1500 87,3 78,0 71,8 2,5 22,2 37,0
B20 66,0 ml/rev 1000 66,0 56,7 50,5 1,7 16,8 28,0
1500 99,0 89,7 83,5 2,8 24,9 41,7
B24 79,5 ml/rev 1000 79,5 70,2 64,0 1,9 19,9 33,4
1500 119,3 110,0 103,8 3,0 29,6 49,8
B28 89,7 ml/rev 1000 89,7 80,4 74,2 2,0 22,3 37,5
1500 134,5 125,2 119,0 3,2 33,2 55,9
B31 98,3 ml/rev 1000 98,3 89,0 82,8 2,1 24,3 40,9
1500 147,4 138,1 131,9 3,3 36,2 61,0
B35 111,0 ml/rev 1000 111,0 101,7 95,5 2,3 27,3 46,0
1500 166,5 157,2 151,0 3,5 40,7 68,7
B38 120,3 ml/rev 1000 120,3 111,0 104,8 2,4 29,4 49,8
1500 180,4 171,1 164,9 3,7 43,9 74,3
B421) 136,0 ml/rev 1000 136,0 126,7 120,5 2,6 33,1 56,0
1500 204,0 194,7 188,5 4,0 49,4 83,7
B451) 145,7 ml/rev 1000 145,7 136,4 130,2 2,7 35,3 59,9
1500 218,5 209,2 203,0 4,1 52,8 89,5
B501) 158,0 ml/rev 1000 158,0 148,7 145,02) 2,8 38,2 56,82)
1500 237,0 227,7 224,02) 4,4 57,0 85,02)
1) 2)
B42 - B45 - B50 = 2200 R.P.M. max. B50 = 210 bar max. int. Port connection can be furnished with metric threads.

15

BACK TO THE TABLE OF CONTENT

 ORDERING CODE - T6E* SERIES MOBILE APPLICATION

Model No. T6E* - 066 - 3 R 00 - B 1

Series M = Mobile 1 shaft seal Modification

Series P = Mobile 2 shaft seals
Seal class
Cam ring 1 = S1 (for mineral oil)
(Delivery at 0 bar & 1500 r.p.m.) 4 = S4 (for the resistant fluids)
042 = 198,5 l/min 062 = 295,0 l/min 5 = S5 (for mineral oil and fire
045 = 213,6 l/min 066 = 319,9 l/min resistant fluids)
050 = 237,7 l/min 072 = 340,6 l/min
052 = 247,2 l/min Design letter
Type of shaft Type of shaft Porting combination
M version P version 00 = standard
1 = keyed (SAE CC) Direct. of rotation (view on shaft end)
2 = keyed (no SAE) R = clockwise
3 = splined (SAE C) 3 = splined (no SAE) L = counter-clockwise
4 = splined (SAE CC)
T = splined (SAE J718c)
P = Pressure port
S = Suction port

INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)

T6EM - 050

Lp. Noise level [db(A)] 1m ISO 4412

Internal leakage Qs [l/min]

Pressure p [bar] Pressure p [bar]

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]

Load F [N]

Pressure p [bar] Speed n [RPM]

Maximum permissible axial load Fa = 2000 N

16

BACK TO THE TABLE OF CONTENT

 DIMENSIONS & OPERATING CHARACTERISTICS - Weight : 43,3 kg - T6E* SERIES MOBILE APPLICATION

Additional T6EM shaft code T: see page 33

Additional T6EP version shaft see page 33
Shaft torque limits [ml/rev x bar]
Pump Shaft V x p max.
T6EM 2 34590
OPERATING CHARACTERISTICS - TYPICAL [24 cSt]
Series Volumetric Speed Flow Q [l/min] Input power P [kW]
Displacement Vp n [R.P.M.] p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
042 132,3 ml/rev 1000 132,3 122,3 115,2 3,2 32,9 55,2
1500 198,5 188,5 181,3 5,2 49,4 82,6
045 142,4 ml/rev 1000 142,4 132,4 125,3 3,4 35,3 59,2
1500 213,6 203,6 196,5 5,4 52,9 88,7
050 158,5 ml/rev 1000 158,5 148,5 141,4 3,5 39,0 65,6
1500 237,7 227,7 220,6 5,7 58,5 98,3
052 164,8 ml/rev 1000 164,8 154,8 147,7 3,6 40,5 68,2
1500 247,2 237,2 230,1 5,8 60,8 102,1
062 196,7 ml/rev 1000 196,7 186,7 179,6 4,0 47,9 80,9
1500 295,0 285,0 277,9 6,4 71,9 121,3
066 213,3 ml/rev 1000 213,3 203,3 196,2 4,2 51,8 87,6
1500 319,9 309,9 302,8 6,7 77,7 131,2
072 227,1 ml/rev 1000 227,1 217,1 210,0 4,3 55,0 93,1
1500 340,6 330,6 323,5 6,9 82,6 139,5
Port connection can be furnished with metric threads.

17

BACK TO THE TABLE OF CONTENT

 ORDERING CODE - T6CC* SERIES MOBILE APPLICATION

Model No. T6CC* W - B22 - B08 - 1 R 00 - D 1 - 00

Series M = Mobile 1 shaft seal Modification
Series P = Mobile 2 shaft seals P1 P2 Mounting W/connection variables
Use for severe duty shaft only* P1 = 1" - S = 3" P1 = 1" - 2"1/22)
Cam ring for "P1" & "P2" P2 1" 3/4"1) 1" 3/4"1)
(Delivery at 0 bar & 1500 r.p.m.) Code 00 01 10 11
B03 = 16,2 l/min B17 = 87,4 l/min 1) for 46 ml/rev. max.
B05 = 25,8 l/min B20 = 95,7 l/min 2) for 126 ml/rev. max.
B06 = 31,9 l/min B22 = 105,4 l/min The largest cartridge must be always
B08 = 39,6 l/min B25 = 118,9 l/min mounted in the front.
B10 = 51,1 l/min B28 = 133,2 l/min
B12 = 55,6 l/min B31 = 150,0 l/min Seal class
B14 = 69,0 l/min 1 = S1 (for mineral oil)
4 = S4 (for the resistant fluids)
Type of shaft Type of shaft 5 = S5 (for mineral oil and fire
M version MW severe duty resistant fluids)
1 = keyed (no SAE) *2 = keyed (SAE BB)
3 = splined (SAE BB) *R = keyed special Design letter
5 = splined (SAE B) *X = keyed special
Porting combination (see page 34)
P version *W = keyed special
00 = standard
3 = splined (no SAE) *V = keyed special
4 = splined (SAE BB) *T = splined (SAE J718c) Direct. of rotation (view on shaft end)
6 = splined (no SAE) R = clockwise
L = counter-clockwise

INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)

T6CCM - B22 - B22
Lp. Noise level [db(A)] 1m ISO 4412
Internal leakage Qs [l/min]

Pressure p [bar] Pressure p [bar]

Do not operate the pump more than 5 seconds at any speed or Double pump noise level is given with each section discharging at
viscosity if internal leakage is more than 50% of theoretical flow. the pressure noted on the curve.
Total leakage is the sum of each section loss at its operating
conditions.

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]

Load F [N]

Pressure p [bar] Speed n [RPM]

Total hydrodynamic power loss is the sum of each section at its Maximum permissible axial load Fa = 800 N
operating conditions.

18

BACK TO THE TABLE OF CONTENT

 DIMENSIONS & OPERATING CHARACTERISTICS - Weight : 26,0 kg - T6CC* SERIES MOBILE APPLICATION

Additional special shafts: see page 33

Additional T6CCMW shaft code T: see page 33
Additional T6CCP version shaft see page 33

Port Code A B C D E Shaft torque limits [ml/rev x bar]

S 3" 106,4 61,9 76,2 5/8"-11 x 28,4 deep Pump Shaft V x p max. P1 + P2
S 2"1/2 88,9 50,8 63,5 1/2"-13 x 23,9 deep T6CCM 1 14300
P1 1" 52,4 26,2 25,4 76,2 T6CCMW 2 21420
P2 3/4" 47,7 22,2 19,0 76,2 T6CCM 3 32670
P2 1" 52,4 26,2 25,4 74,7 T6CCM 5 20600

OPERATING CHARACTERISTICS - TYPICAL [24 cSt]

Pressure Series Volumetric Flow Q [l/min] & n = 1500 RPM Input power P [kW] & n = 1500 RPM
port Displacement Vp p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
B03 10,8 ml/rev 16,2 10,7 - 1,3 5,3 -
B05 17,2 ml/rev 25,8 20,3 15,8 1,4 7,5 12,2
B06 21,3 ml/rev 31,9 26,5 22,0 1,5 8,9 14,7
B08 26,4 ml/rev 39,6 34,1 29,6 1,6 10,7 17,7
P1 B10 34,1 ml/rev 51,1 45,7 41,2 1,7 13,4 22,3
B12 37,1 ml/rev 55,6 50,2 45,7 1,7 14,4 24,1
& B14 46,0 ml/rev 69,0 63,5 59,0 1,9 17,6 29,5
B17 58,3 ml/rev 87,4 82,0 77,5 2,1 21,9 36,9
P2
B20 63,8 ml/rev 95,7 90,2 85,7 2,2 23,8 40,2
B22 70,3 ml/rev 105,4 100,0 95,5 2,3 26,1 44,1
B251) 79,3 ml/rev 118,9 113,5 109,0 2,5 29,2 49,5
B281) 88,8 ml/rev 133,2 127,7 124,52) 2,8 32,7 48,52)
B311) 100,0 ml/rev 150,0 144,5 141,32) 2,8 36,5 54,42)
1)
B25 - B28 - B31 = 2500 R.P.M. max. 2) B28 - B31 = 210 bar max. int.
- Not to use because internal leakage greater than 50% theoretical flow. Port connection can be furnished with metric threads.

19

BACK TO THE TABLE OF CONTENT

 ORDERING CODE - T6DC* SERIES MOBILE APPLICATION

Model No. T6DC* W - B38 - B22 - 1 R 00 - C 1

Series M = Mobile 1 shaft seal Modification
Series P = Mobile 2 shaft seals P1 P2
Seal class
Use for severe duty shaft only* 1 = S1 (for mineral oil)
4 = S4 (for the resistant fluids)
Cam ring for "P1"
5 = S5 (for mineral oil and fire
(Delivery at 0 bar & 1500 r.p.m.)
resistant fluids)
B14 = 71,4 l/min B35 = 166,5 l/min
B17 = 87,3 l/min B38 = 180,4 l/min Design letter
B20 = 99,0 l/min B42 = 204,0 l/min
B24 = 119,3 l/min B45 = 218,5 l/min Porting combination (see page 34)
B28 = 134,5 l/min B50 = 237,0 l/min 00 = standard
B31 = 147,4 l/min Direct. of rotation (view on shaft end)
Cam ring for "P2" R = clockwise
(Delivery at 0 bar & 1500 r.p.m.) L = counter-clockwise
B03 = 16,2 l/min B17 = 87,4 l/min Type of shaft Type of shaft
B05 = 25,8 l/min B20 = 95,7 l/min P version M version
B06 = 31,9 l/min B22 = 105,4 l/min 3 = splined (no SAE) 1 = keyed (SAE C)
B08 = 39,6 l/min B25 = 118,9 l/min 2 = keyed (no SAE)
B10 = 51,1 l/min B28 = 133,2 l/min 3 = splined (SAE C)
B12 = 55,6 l/min B31 = 150,0 l/min 4 = splined (no SAE)
B14 = 69,0 l/min MW severe duty
*5 = keyed (no SAE)
*T = splined (SAE J718c)
INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)
T6DCM - B38 - B22
Lp. Noise level [db(A)] 1m ISO 4412
Internal leakage Qs [l/min]

Pressure p [bar] Pressure p [bar]

Do not operate the pump more than 5 seconds at any speed or Double pump noise level is given with each section discharging at
viscosity if internal leakage is more than 50% of theoretical flow. the pressure noted on the curve.
Total leakage is the sum of each section loss at its operating
conditions.

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]

Load F [N]

Pressure p [bar] Speed n [RPM]

Total hydrodynamic power loss is the sum of each section at its Maximum permissible axial load Fa = 1200 N
operating conditions.

20

BACK TO THE TABLE OF CONTENT

 DIMENSIONS & OPERATING CHARACTERISTICS - Weight : 36,6 kg - T6DC* SERIES MOBILE APPLICATION

Additional T6DCM shaft code T: see page 33

Additional T6DCP version shaft see page 33

Shaft torque limits [ml/rev x bar]

Pump Shaft V x p max. P1 + P2
T6DCM 1 43240
T6DCM 2 34590
T6DCMW 5 55600
OPERATING CHARACTERISTICS - TYPICAL [24 cSt]
Pressure Series Volumetric Flow Q [l/min] & n = 1500 RPM Input power P [kW] & n = 1500 RPM
port Displacement Vp p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
B14 47,6 ml/rev 71,4 62,1 55,9 2,3 18,5 30,6
B17 58,2 ml/rev 87,3 78,0 71,8 2,5 22,2 37,0
B20 66,0 ml/rev 99,0 89,7 83,5 2,8 24,9 41,7
B24 79,5 ml/rev 119,3 110,0 103,8 3,0 29,6 49,8
P1 B28 89,7 ml/rev 134,5 125,2 119,0 3,2 33,2 55,9
B31 98,3 ml/rev 147,4 138,1 131,9 3,3 36,2 61,0
B35 111,0 ml/rev 166,5 157,2 151,0 3,5 40,7 68,7
B38 120,3 ml/rev 180,4 171,1 164,9 3,7 43,9 74,3
B422) 136,0 ml/rev 204,0 194,7 188,5 4,0 49,4 83,7
B452) 145,7 ml/rev 218,5 209,2 203,0 4,1 52,8 89,5
2)
B50 158,0 ml/rev 237,0 227,7 224,01) 4,4 57,0 85,01)
B03 10,8 ml/rev 16,2 10,7 - 1,3 5,3 -
B05 17,2 ml/rev 25,8 20,3 15,8 1,4 7,5 12,2
B06 21,3 ml/rev 31,9 26,5 22,0 1,5 8,9 14,7
B08 26,4 ml/rev 39,6 34,1 29,6 1,6 10,7 17,7
B10 34,1 ml/rev 51,1 45,7 41,2 1,7 13,4 22,3
B12 37,1 ml/rev 55,6 50,2 45,7 1,7 14,4 24,1
P2 B14 46,0 ml/rev 69,0 63,5 59,0 1,9 17,6 29,5
B17 58,3 ml/rev 87,4 82,0 77,5 2,1 21,9 36,9
B20 63,8 ml/rev 95,7 90,2 85,7 2,2 23,8 40,2
B22 70,3 ml/rev 105,4 100,0 95,5 2,3 26,1 44,1
B25 79,3 ml/rev 118,9 113,5 109,0 2,5 29,2 49,5
B28 88,8 ml/rev 133,2 127,7 124,51) 2,8 32,7 48,51)
B31 100,0 ml/rev 150,0 144,5 141,31) 2,8 36,5 54,41)
1) 2)
B28 - B31 - B50 = 210 bar max. int. B42 - B45 - B50 = 2200 R.P.M. max
- Not to use because internal leakage greater than 50% theoretical flow Port connection can be furnished with metric threads.

21

BACK TO THE TABLE OF CONTENT

 ORDERING CODE - T6EC* SERIES MOBILE APPLICATION

Model No. T6EC* - 066 - B22 - 1 R 00 - C 1 -

Series M = Mobile 1 shaft seal P1 P2 Modification

Series P = Mobile 2 shaft seals
Seal class
Cam ring for "P1" 1 = S1 (for mineral oil)
(Delivery at 0 bar & 1500 r.p.m.) 4 = S4 (for the resistant fluids)
042 = 198,5 l/min 062 = 295,0 l/min 5 = S5 (for mineral oil and fire
045 = 213,6 l/min 066 = 319,9 l/min resistant fluids)
050 = 237,7 l/min 072 = 340,6 l/min
052 = 247,2 l/min Design letter
Cam ring for "P2" Porting combination (see page 34)
(Delivery at 0 bar & 1500 r.p.m.) 00 = standard
B03 = 16,2 l/min B17 = 87,4 l/min Direct. of rotation (view on shaft end)
B05 = 25,8 l/min B20 = 95,7 l/min R = clockwise
B06 = 31,9 l/min B22 = 105,4 l/min L = counter-clockwise
B08 = 39,6 l/min B25 = 118,9 l/min
B10 = 51,1 l/min B28 = 133,2 l/min Type of shaft Type of shaft
B12 = 55,6 l/min B31 = 150,0 l/min P version M version
B14 = 69,0 l/min 3 = splined (no SAE) 1 = keyed (SAE CC)
2 = keyed (no SAE)
3 = splined (SAE C)
4 = splined (SAE CC)
T = splined (SAE J718c)
INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)
T6ECM - 050 - B22
Lp. Noise level [db(A)] 1m ISO 4412
Internal leakage Qs [l/min]

Pressure p [bar] Pressure p [bar]

Do not operate the pump more than 5 seconds at any speed or Double pump noise level is given with each section discharging at
viscosity if internal leakage is more than 50% of theoretical flow. the pressure noted on the curve.
Total leakage is the sum of each section loss at its operating
conditions.

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]

Load F [N]

Pressure p [bar] Speed n [RPM]

Total hydrodynamic power loss is the sum of each section at its Maximum permissible axial load Fa = 2000 N
operating conditions.

22

BACK TO THE TABLE OF CONTENT

 DIMENSIONS & OPERATING CHARACTERISTICS - Weight : 55,0 kg - T6EC* SERIES MOBILE APPLICATION

Shaft torque limits [ml/rev x bar]

Pump Shaft V x p max. P1 + P2
1 72306
Additional T6ECMW shaft code T: see page 33 T6ECM
Additional T6ECP version shaft see page 33 2 34590
3 61200
OPERATING CHARACTERISTICS - TYPICAL [24 cSt]
Pressure Series Volumetric Flow Q [l/min] & n = 1500 RPM Input power P [kW] & n = 1500 RPM
port Displacement Vp p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
042 132,3 ml/rev 198,5 188,5 181,3 5,2 49,4 82,6
045 142,4 ml/rev 213,6 203,6 196,5 5,4 52,9 88,7
050 158,5 ml/rev 237,7 227,7 220,6 5,7 58,5 98,3
P1
052 164,8 ml/rev 247,2 237,2 230,1 5,8 60,8 102,1
062 196,7 ml/rev 295,0 285,0 277,9 6,4 71,9 121,3
066 213,3 ml/rev 319,9 309,9 302,8 6,7 77,7 131,2
072 227,1 ml/rev 340,6 330,6 323,5 6,9 82,6 139,5
B03 10,8 ml/rev 16,2 10,7 - 1,3 5,3 -
B05 17,2 ml/rev 25,8 20,3 15,8 1,4 7,5 12,2
B06 21,3 ml/rev 31,9 26,5 22,0 1,5 8,9 14,7
B08 26,4 ml/rev 39,6 34,1 29,6 1,6 10,7 17,7
B10 34,1 ml/rev 51,1 45,7 41,2 1,7 13,4 22,3
B12 37,1 ml/rev 55,6 50,2 45,7 1,7 14,4 24,1
P2 B14 46,0 ml/rev 69,0 63,5 59,0 1,9 17,6 29,5
B17 58,3 ml/rev 87,4 82,0 77,5 2,1 21,9 36,9
B20 63,8 ml/rev 95,7 90,2 85,7 2,2 23,8 40,2
B22 70,3 ml/rev 105,4 100,0 95,5 2,3 26,1 44,1
B25 79,3 ml/rev 118,9 113,5 109,0 2,5 29,2 49,5
B28 88,8 ml/rev 133,2 127,7 124,51) 2,8 32,7 48,51)
B31 100,0 ml/rev 150,0 144,5 141,31) 2,8 36,5 54,41)
1)
B28 - B31 = 210 bar max. int. - Not to use because internal leakage greater than 50% theoretical flow
Port connection can be furnished with metric threads.

23

BACK TO THE TABLE OF CONTENT

 ORDERING CODE - T6ED* SERIES MOBILE APPLICATION

Model No. T6ED* - 066 - B38 - 1 R 00 - C 1 -

Series M = Mobile 1 shaft seal P1 P2 Modification

Series P = Mobile 2 shaft seals
Seal class
Cam ring for "P1" 1 = S1 (for mineral oil)
(Delivery at 0 bar & 1500 r.p.m.) 4 = S4 (for the resistant fluids)
042 = 198,5 l/min 062 = 295,0 l/min 5 = S5 (for mineral oil and fire
045 = 213,6 l/min 066 = 319,9 l/min resistant fluids)
050 = 237,7 l/min 072 = 340,6 l/min
052 = 247,2 l/min Design letter
Cam ring for "P2" Porting combination (see page 34)
(Delivery at 0 bar & 1500 r.p.m.) 00 = standard
B14 = 71,4 l/min B35 = 166,5 l/min Direct. of rotation (view on shaft end)
B17 = 87,3 l/min B38 = 180,4 l/min R = clockwise
B20 = 99,0 l/min B42 = 204,0 l/min L = counter-clockwise
B24 = 119,3 l/min B45 = 218,5 l/min
B28 = 134,5 l/min B50 = 237,0 l/min Type of shaft Type of shaft
B31 = 147,4 l/min P version M version
3 = splined (no SAE) 1 = keyed (SAE CC)
2 = keyed (no SAE)
3 = splined (SAE C)
4 = splined (SAE CC)
T = splined (SAE J718c)
INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)
T6EDM - 050 - B38

Lp. Noise level [db(A)] 1m ISO 4412

Internal leakage Qs [l/min]

Pressure p [bar] Pressure p [bar]

Total leakage is the sum of each section loss at its operating Double pump noise level is given with each section discharging at
conditions. the pressure noted on the curve.

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]

Load F [N]

Pressure p [bar] Speed n [RPM]

Total hydrodynamic power loss is the sum of each section at its Maximum permissible axial load Fa = 2000 N
operating conditions.

24

BACK TO THE TABLE OF CONTENT

 DIMENSIONS & OPERATING CHARACTERISTICS - Weight : 66,0 kg - T6ED* SERIES MOBILE APPLICATION

Shaft torque limits [ml/rev x bar]

Pump Shaft V x p max. P1 + P2
Additional T6EDM shaft code T: see page 33 1 72306
Additional T6EDP version shaft see page 33 T6EDM 2 34590
OPERATING CHARACTERISTICS - TYPICAL [24 cSt] 3 61200

Pressure Series Volumetric Flow Q [l/min] & n = 1500 RPM Input power P [kW] & n = 1500 RPM
port Displacement Vp p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
042 132,3 ml/rev 198,5 188,5 181,3 5,2 49,4 82,6
045 142,4 ml/rev 213,6 203,6 196,5 5,4 52,9 88,7
050 158,5 ml/rev 237,7 227,7 220,6 5,7 58,5 98,3
P1
052 164,8 ml/rev 247,2 237,2 230,1 5,8 60,8 102,1
062 196,7 ml/rev 295,0 285,0 277,9 6,4 71,9 121,3
066 213,3 ml/rev 319,9 309,9 302,8 6,7 77,7 131,2
072 227,1 ml/rev 340,6 330,6 323,5 6,9 82,6 139,5
B14 47,6 ml/rev 71,4 62,1 55,9 2,3 18,5 30,6
B17 58,2 ml/rev 87,3 78,0 71,8 2,5 22,2 37,0
B20 66,0 ml/rev 99,0 89,7 83,5 2,8 24,9 41,7
B24 79,5 ml/rev 119,3 110,0 103,8 3,0 29,6 49,8
P2 B28 89,7 ml/rev 134,5 125,2 119,0 3,2 33,2 55,9
B31 98,3 ml/rev 147,4 138,1 131,9 3,3 36,2 61,0
B35 111,0 ml/rev 166,5 157,2 151,0 3,5 40,7 68,7
B38 120,3 ml/rev 180,4 171,1 164,9 3,7 43,9 74,3
B42 136,0 ml/rev 204,0 194,7 188,5 4,0 49,4 83,7
B45 145,7 ml/rev 218,5 209,2 203,0 4,1 52,8 89,5
B50 158,0 ml/rev 237,0 227,7 224,01) 4,4 57,0 85,01)
1)
B50 = 210 bar max. int. Port connection can be furnished with metric threads.

25

BACK TO THE TABLE OF CONTENT

 ORDERING CODE & OPERATING CHARACTERISTICS - T6DCCM SERIES MOBILE APPLICATION

Model No. T6DCCM - B38 - B28 - B08 - 1 R 00 - B 1 - 00

Series P2 P3 Modification
P1
Cam ring for "P1" Mounting W/connection variables
(Delivery at 0 bar & 1500 r.p.m.) Type UNC Metric
B14 = 71,4 l/min B35 = 166,5 l/min
B17 = 87,3 l/min B38 = 180,4 l/min P3 1" 3/4" 1" 3/4"
B20 = 99,0 l/min B42 = 204,0 l/min Code 00 01 M0 M1
B24 = 119,3 l/min B45 = 218,5 l/min
B28 = 134,5 l/min B50 = 237,0 l/min Seal class
B31 = 147,4 l/min 1 = S1 (for mineral oil)
4 = S4 (for the resistant fluids)
Cam ring for "P2" & "P3" 5 = S5 (for mineral oil and fire
(Delivery at 0 bar & 1500 r.p.m.) resistant fluids)
B03 = 16,2 l/min B17 = 87,4 l/min
B05 = 25,8 l/min B20 = 95,7 l/min Design letter
B06 = 31,9 l/min B22 = 105,4 l/min Porting combination (see pages 34 - 35)
B08 = 39,6 l/min B25 = 118,9 l/min 00 = standard
B10 = 51,1 l/min B28 = 133,2 l/min
B12 = 55,6 l/min B31 = 150,0 l/min Direct. of rotation (view on shaft end)
B14 = 69,0 l/min R = clockwise
L = counter-clockwise
Type of shaft
1 = keyed (no SAE)
2 = keyed (SAE CC)
3 = splined (SAE C)
4 = splined (SAE CC)
6 = splined (no SAE)

OPERATING CHARACTERISTICS - TYPICAL [24 cSt]

Pressure Series Volumetric Flow Q [l/min] & n = 1500 RPM Input power P [kW] & n = 1500 RPM
port Displacement Vp p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
B14 47,6 ml/rev 71,4 62,1 55,9 2,3 18,5 30,6
B17 58,2 ml/rev 87,3 78,0 71,8 2,5 22,2 37,0
B20 66,0 ml/rev 99,0 89,7 83,5 2,8 24,9 41,7
B24 79,5 ml/rev 119,3 110,0 103,8 3,0 29,6 49,8
P1 B28 89,7 ml/rev 134,5 125,2 119,0 3,2 33,2 55,9
B31 98,3 ml/rev 147,4 138,1 131,9 3,3 36,2 61,0
B35 111,0 ml/rev 166,5 157,2 151,0 3,5 40,7 68,7
B38 120,3 ml/rev 180,4 171,1 164,9 3,7 43,9 74,3
B422) 136,0 ml/rev 204,0 194,7 188,5 4,0 49,4 83,7
B452) 145,7 ml/rev 218,5 209,2 203,0 4,1 52,8 89,5
B502) 158,0 ml/rev 237,0 227,7 224,01) 4,4 57,0 85,01)
B03 10,8 ml/rev 16,2 10,7 - 1,3 5,3 -
B05 17,2 ml/rev 25,8 20,3 15,8 1,4 7,5 12,2
B06 21,3 ml/rev 31,9 26,5 22,0 1,5 8,9 14,7
B08 26,4 ml/rev 39,6 34,1 29,6 1,6 10,7 17,7
P2 B10 34,1 ml/rev 51,1 45,7 41,2 1,7 13,4 22,3
B12 37,1 ml/rev 55,6 50,2 45,7 1,7 14,4 24,1
& B14 46,0 ml/rev 69,0 63,5 59,0 1,9 17,6 29,5
B17 58,3 ml/rev 87,4 82,0 77,5 2,1 21,9 36,9
P3
B20 63,8 ml/rev 95,7 90,2 85,7 2,2 23,8 40,2
B22 70,3 ml/rev 105,4 100,0 95,5 2,3 26,1 44,1
B25 79,3 ml/rev 118,9 113,5 109,0 2,5 29,2 49,5
B28 88,8 ml/rev 133,2 127,7 124,51) 2,8 32,7 48,51)
B31 100,0 ml/rev 150,0 144,5 141,31) 2,8 36,5 54,41)
1)
B28 - B31 - B50 = 210 bar max. int. 2) B42 - B45 - B50 = 2200 R.P.M. max
- Not to use because internal leakage greater than 50% theoretical flow

26

BACK TO THE TABLE OF CONTENT

27

DIMENSIONS - Weight : 61,0 kg - T6DCCM SERIES MOBILE APPLICATION

Shaft torque limits [ml/rev x bar] Alternate port
Pump Shaft Vi x p max. P1 + P2 + P3 Shaft Vi x p max. P1 + P2 + P3 Port Code A B C
1 43240 3 61200 P3 00 & M0 52,4 26,2 25,4
T6DCCM 2 66500 4 66500 P3 01 & M1 47,6 22,2 19,0

BACK TO THE TABLE OF CONTENT

 TECHNICAL DATA - T6DCCM SERIES MOBILE APPLICATION

INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)

T6DCCM - B38 - B22 - B22

Lp. Noise level [db(A)] 1m ISO 4412

Internal leakage Qs [l/min]

Pressure p [bar] Pressure p [bar]

Total leakage is the sum of each section loss at its operating Triple pump noise level is given with each section discharging at
conditions. the pressure noted on the curve.

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]

Load F [N]

Pressure p [bar] Speed n [RPM]

Total hydrodynamic power loss is the sum of each section at its Maximum permissible axial load Fa = 800 N
operating conditions.

28

BACK TO THE TABLE OF CONTENT

 TECHNICAL DATA - T6EDC* SERIES MOBILE APPLICATION

INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)

T6EDCM - 062 - B35 - B17

Lp. Noise level [db(A)] 1m ISO 4412

Internal leakage Qs [l/min]

Pressure p [bar] Pressure p [bar]

Total leakage is the sum of each section loss at its operating Triple pump noise level is given with each section discharging at
conditions. the pressure noted on the curve.

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]

Load F [N]

Pressure p [bar] Speed n [RPM]

Total hydrodynamic power loss is the sum of each section at its Maximum permissible axial load Fa = 2000 N
operating conditions.

29

BACK TO THE TABLE OF CONTENT

 DIMENSIONS - Weight : 100,0 kg - T6EDCM SERIES MOBILE APPLICATION

25,4
19,0
C
Alternate port

26,2
22,2
B
52,4
47,6
A
Code
0
1
Port
P3
P3

30

BACK TO THE TABLE OF CONTENT

 DIMENSIONS - Weight : 100,0 kg - T6EDCS SERIES MOBILE APPLICATION

25,4
19,0
C
Alternate port

26,2
22,2
B
52,4
47,6
A
Code
0
1
Port
P3
P3

31

BACK TO THE TABLE OF CONTENT

 ORDERING CODE & OPERATING CHARACTERISTICS - T6EDC* SERIES MOBILE APPLICATION

T6EDCS
Model No. T6EDCM - 062 - B35 - B17 - 1 R 00 - A 1 - P 0 -

Series P1 P2 P3 Modification
Cam ring for "P1" Mounting W/connection variables
(Delivery at 0 bar & 1500 r.p.m.) 0 = P3 = 1" SAE
042 = 198,5 l/min 062 = 295,0 l/min 1 = P3 = 3/4" SAE
045 = 213,6 l/min 066 = 319,9 l/min
050 = 237,7 l/min 072 = 340,6 l/min Options
052 = 247,2 l/min F = Standard
P = 4 holes for external support
Cam ring for "P2"
(Delivery at 0 bar & 1500 r.p.m.) Seal class
B14 = 71,4 l/min B35 = 166,5 l/min 1 = S1 (for mineral oil)
B17 = 87,3 l/min B38 = 180,4 l/min 4 = S4 (for the resistant fluids)
B20 = 99,0 l/min B42 = 204,0 l/min 5 = S5 (for mineral oil and fire
B24 = 119,3 l/min B45 = 218,5 l/min resistant fluids)
B28 = 134,5 l/min B50 = 237,0 l/min Design letter
B31 = 147,4 l/min
Porting combination (see pages 34 - 35)
Cam ring for "P3" 00 = standard
(Delivery at 0 bar & 1500 r.p.m.)
B03 = 16,2 l/min B17 = 87,4 l/min Direct. of rotation (view on shaft end)
B05 = 25,8 l/min B20 = 95,7 l/min R = clockwise
B06 = 31,9 l/min B22 = 105,4 l/min L = counter-clockwise
B08 = 39,6 l/min B25 = 118,9 l/min Type of shaft
B10 = 51,1 l/min B28 = 133,2 l/min 1 = keyed (G45N - ISO 3019-2) (T6EDCM)
B12 = 55,6 l/min B31 = 150,0 l/min 2 = keyed (SAE D & E) (T6EDCS)
B14 = 69,0 l/min 3 = splined (SAE D & E) (T6EDCM-T6EDCS)

OPERATING CHARACTERISTICS - TYPICAL [24 cSt]

Pressure Series Volumetric Flow Q [l/min] & n = 1500 RPM Input power P [kW] & n = 1500 RPM
port Displacement Vp p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
042 132,3 ml/rev 198,5 188,5 181,3 5,2 49,4 82,6
045 142,4 ml/rev 213,6 203,6 196,5 5,4 52,9 88,7
050 158,5 ml/rev 237,7 227,7 220,6 5,7 58,5 98,3
P1
052 164,8 ml/rev 247,2 237,2 230,1 5,8 60,8 102,1
062 196,7 ml/rev 295,0 285,0 277,9 6,4 71,9 121,3
066 213,3 ml/rev 319,9 309,9 302,8 6,7 77,7 131,2
072 227,1 ml/rev 340,6 330,6 323,5 6,9 82,6 139,5
B14 47,6 ml/rev 71,4 62,1 55,9 2,3 18,5 30,6
B17 58,2 ml/rev 87,3 78,0 71,8 2,5 22,2 37,0
B20 66,0 ml/rev 99,0 89,7 83,5 2,8 24,9 41,7
B24 79,5 ml/rev 119,3 110,0 103,8 3,0 29,6 49,8
P2 B28 89,7 ml/rev 134,5 125,2 119,0 3,2 33,2 55,9
B31 98,3 ml/rev 147,4 138,1 131,9 3,3 36,2 61,0
B35 111,0 ml/rev 166,5 157,2 151,0 3,5 40,7 68,7
B38 120,3 ml/rev 180,4 171,1 164,9 3,7 43,9 74,3
B42 136,0 ml/rev 204,0 194,7 188,5 4,0 49,4 83,7
B45 145,7 ml/rev 218,5 209,2 203,0 4,1 52,8 89,5
B50 158,0 ml/rev 237,0 227,7 224,01) 4,4 57,0 85,01)
B03 10,8 ml/rev 16,2 10,7 - 1,3 5,3 -
B05 17,2 ml/rev 25,8 20,3 15,8 1,4 7,5 12,2
B06 21,3 ml/rev 31,9 26,5 22,0 1,5 8,9 14,7
B08 26,4 ml/rev 39,6 34,1 29,6 1,6 10,7 17,7
B10 34,1 ml/rev 51,1 45,7 41,2 1,7 13,4 22,3
B12 37,1 ml/rev 55,6 50,2 45,7 1,7 14,4 24,1
B14 46,0 ml/rev 69,0 63,5 59,0 1,9 17,6 29,5
P3
B17 58,3 ml/rev 87,4 80,0 77,5 2,1 21,9 36,9
B20 63,8 ml/rev 95,7 90,2 85,7 2,2 23,8 40,2
B22 70,3 ml/rev 105,4 100,0 95,5 2,3 26,1 44,1
B25 79,3 ml/rev 118,9 113,5 109,0 2,5 29,2 49,5
B28 88,8 ml/rev 133,2 127,7 124,51) 2,8 32,7 48,51)
B31 100,0 ml/rev 150,0 144,5 141,31) 2,8 36,5 54,41)
1)
B28 - B31 - B50 = 210 bar max. int. - Not to use because internal leakage greater than 50% theoretical flow

32

BACK TO THE TABLE OF CONTENT

 ADDITIONAL SHAFTS - T6 SERIES MOBILE APPLICATION

ADDITIONAL P VERSION

T6CCP T6CCP T6CCP

Shaft torque limits Shaft torque limits Shaft torque limits
20600 [ml/rev x bar] 32670 [ml/rev x bar] 32670 [ml/rev x bar]

T6DP T6DCP T6EP-T6ECP

T6EDP
Shaft torque limits
61200 [ml/rev x bar]

* Drain hole between double shaft seals.

ADDITIONAL SHAFT CODE T : 540 RPM POWER TAKE-OFF - SAE J718C FOR FARM TRACTORS
Shaft torque limits
T6CCMW - 32670 [ml/rev x bar]
T6DCMW - 66600 [ml/rev x bar]
T6DM T6EM - T6ECM - T6EDM - 70400 [ml/rev x bar]

ADDITIONAL SPECIAL T6CCMW SHAFTS

Shaft Code R Shaft Code V Shaft Code X Shaft Code W
Shaft torque limits Shaft torque limits Shaft torque limits Shaft torque limits
18100 [ml/rev x bar] 32670 [ml/rev x bar] 25400 [ml/rev x bar] 32670 [ml/rev x bar]

33

BACK TO THE TABLE OF CONTENT

 PORTING DIAGRAMS - T6 SERIES MOBILE APPLICATION

T6CC* - T6DC* - T6EC*

T6ED*

T6DCCM - T6EDC*

34

BACK TO THE TABLE OF CONTENT

 PORTING DIAGRAMS - T6 SERIES MOBILE APPLICATION

T6DCCM - T6EDC*

35

BACK TO THE TABLE OF CONTENT