Hydroirma Catalog Gear Pump

Gear Pumps
motion and progress
200 - P - 991218 - E - 00/06.02 1 / 104

Balancing Drive gear Oil seals
seals
Front cover
Oil retaining ring

Bushings
Rear cover
Pump body
Mounting tie rods Driven gear
Index
1 General information 3
2 Technical information 4
3 Gear pumps group AP05 16
7 Accessories 94
8 Composition of product code 99
200 - P - 991218 - E - 00/06.02 2/104

1 General information
1.1 Introduction to the product

Gear pumps are widely used in modern hydraulic systems - carefully controlled heat treatments
due to their high performance, long service life, and low - increasingly tight coupling tolerances, and a high stanĆ
purchase and maintenance costs. dard of surface finish.
Product development has made it possible to achieve Bucher Hydraulics S.p.A. has achieved these results by
high operating pressures, excellent volumetric and mechĆ constantly improving its design, control, and manufacturĆ
anical efficiency, and lower noise levels, in operation, by ing techniques in line with the latest technological develĆ
means of: opments, while simultaneously introducing a Quality ConĆ
- meticulous CAD design of the gear teeth and balancing trol System which ensures that every single product offers
areas the same high standards.
- an exacting choice of high-performance materials
Product description 4 5
A-A 1 B A B-B
10
6 3
B A
9 2
1 - Drive gear 6 - Rear cover

2 - Driven gear 7 - Mounting tie rods
3 - Bushings 8 - Balancing seals
4 - Pump body 9 - Oil seals
5 - Front cover 10 - Oil retaining ring
Referring to the pump shown in the figure, the drive gear (1) - An oil retaining ring with the dual purpose of preventing
drives round the driven gear (2), transferring the oil from the oil leaks from the drive gear shaft and preventing dust or
suction port to the pressure port as it turns round. other pollutants from entering the pump itself. Unless otherĆ
The gears are made from high strength steel alloy. wise specified, the seals are in nitrilic compound offering
The bushings (3) serve a dual purpose: high mechanical strength and heat resistance.
- to act as a bearing for the gears Viton seals are available on request.
- to balance axial and radial thrust in proportion to the (see 2.2 Recommended fluids/Allowed temperatures)
change in operating pressure.
The gears-bushings assembly is fitted inside the pump Versions available
body (4), in which generally the suction and pressure ports The Bucher Hydraulics S.p.A. product range includes single
are formed. The pump body is made of high strength pumps of groups 05-100-200-300 (corresponding to the
extruded aluminium alloy. The front cover (5), which also common group denominations: 05-1-2-3) and several
acts as a mounting flange, and the rear cover (6) are conĆ combinations of double pumps, triple pumps, and so on,
nected to one another by mounting tie rods (7). that can be assembled together according to versions of
The pump assembly is completed by a series of seals: displacement, flanging, and auxiliary valves indicated in this
- Balancing seals (8) can be fitted in recesses in the bushĆ catalogue.
ings as shown in the figure, or in the covers. Their purpose Bucher Hydraulics S.p.A. will examine any request for
is to delimit the longitudinal balancing area separating the special versions, features, and customisations not shown in
suction and pressure zones. this catalogue. To make such a request, please contact our
- Oil seals (9) prevent oil from leaking out. Sales Department.
200 - P - 991218 - E - 00/06.02 3/104

1.2 Non-standard symbols used in the text
Check nut O-Ring
Woodruff key
Lock washer
Square key
11
Hexagonal-head screw ( TE screw)
Dinamometric spanners
4
Socket head screw (TCE screw)
2 Technical information
2.1 Identifying the rotation direction
The rotation direction of a gear pump is identified by looking for suction and pressure.
at the pump from the front and with the drive gear turned Pumps with a unidirectional rotation (D or S) have the denoĆ
upwards (see figures below). mination AP. Pumps with reversible rotation have the denoĆ
Pumps with clockwise rotation (D) have a drive gear which mination APR.
turns clockwise, with the suction port on the left and the presĆ It is possible to change the rotation direction of the entire
sure port on the right. range of pumps without having to replace any component,
Pumps with counterclockwise rotation (S) have a drive gear except for the AP100 group, for which it is necessary to
which turns counterclockwise, with the suction port on the replace the front cover.
right and the pressure port on the left. To ensure a good technical result, we recommend in any
The figure also shows the pressure flow inside the pumps as case that such inversion be carried out at our factory.
the oil is transferred from the suction port to the pressure Technical descriptions are available on request, which show
port. the correct procedure for the pump rotation inversion.
As regards reversible pumps (R), the ports are alternatively
D Right-hand rotation D
Pressure flow
P
Suction Pressure
S Left-hand rotation S Pressure flow
P
Pressure Suction
R Reversible rotation R
Pressure flow
Suction Pressure
Pressure Suction
200 - P - 991218 - E - 00/06.02 4/104

2.2 Recommended fluids/Allowed
temperatures
We recommend using only mineral oil-based hydraulic
fluids that comply with the ISO/DIN standards.
Viscosity range: recommended 20 120 mm2/s (cSt)
permitted up to 700 mm2/s (cSt)
Operating temperature
Temperature * Caution! – Use of pumps at temperatures above 80°C must always be

Type of seals
AP05–APR05 AP100–AP200–AP300 agreed upon with our Technical Office, and in any case this can cause
a significant worsening in the volumetric efficiency.
Buna N -15 ÷ 65_ C -15 ÷ 80_ C
For use under conditions different from those indicated in this cata-
Viton* -10 ÷ 80_ C -10 ÷ 120_ C logue, please contact our Sales Department.
2.3 Suction
The absolute suction pressure must be V 0.75 bar (11 PSI); (Example 1)
P
therefore, the following must be avoided: M V
- large height differences between pump and tank
- long stretches of piping
- special features such as: M
bends
reductions in diameter
quick couplings
etc.
It is also advisable to choose a filter of a suitable size to
minimise any pressure drop and to take measures to prevent
gradual clogging over time.
(Example 1) (Example 2)
In certain cases, the suction pressure can exceed 1 bar

(14.3 PSI), or atmospheric pressure.
For pumps in the standard configuration, the pressure read M1 M
on the pressure gauge M1 should be:
M1 3.5 bar (50 PSI)
If in a particular application the M1 pressure is higher than
P
the recommended value, contact our Sales Office.
The diameter of the suction pipe should ensure that the oil
speed will fall within the range: v = 0.6 – 1.2 m/s. M
(Example 2)
2.4 Filtration > 170 bar < 170 bar

Operating pressure 2430 PSI 2430 PSI
A short service life of a gear pump is normally due to the
Contamination
presence of impurities in the oil. 9 10
class NAS 1638
It is therefore essential to have an effective filter in the system
Contamination
and to carry out regular maintenance to ensure a long, 18/15 19/16
class ISO 4406
trouble-free service life.
When possible and compatible with the hydraulic circuit Obtain with filter
20 25
ßx = 75
installed, Bucher Hydraulics S.p.A. recommends that the
system have total filtration (suction, pressure, return). We also recommend that an adequate air filter be installed
In any case, the filtering system must constantly ensure an on the tank to prevent contaminating substances such as
oil contamination class equal to or less than those shown in dust, sand, etc. from getting into the oil, as these substances
the following table. can enter the tank through the air flow caused by the level
variations in the tank itself.
200 - P - 991218 - E - 00/06.02 5/104

2.5 Motor-Pump Coupling
M
M
2.5 –: 3.5
H
h
Absolutely no radial or axial forces should be transmitted to The distance between the ends of the shafts must be
the drive shaft in the motor-pump coupling. between 2.5 3.5 mm (.10” .14”).
Such forces cause rapid and irregular wear on the balancing Make sure that the splined coupling is suitably lubricated to
surface of the bushings and gear support, with a conseĆ protect it against rapid deterioration.
quent worsening in pump performance. If there are radial and/or axial loads on the drive shaft, such
The coupling joint must be able to absorb any discrepancies as when it is driven by a V-belt and pulley or pair of gear
in the coaxial alignment of the motor-pump shafts without wheels, it should be fitted with a front cover with supporting
placing any load on the pump shaft. bearings. (See examples 1 and 2)
In the couplings between splined shafts, the connecting Depending on the pump model concerned, these supports
sleeve must be free to move along its axis. can replace the front cover of the pump (e.g. 201 K8 and 201
The length of the sleeve must be sufficient to cover the K0) or can be fitted in addition to and over the front cover
splined sections of the motor-pump shafts completely in (e.g. TC35K1 ć TC35K4 ć TC40K1 ć TC40K2 codes).
any position.
(Example 1)
(Example 2)
T1
Fr
Fr
T2 Fr
a a
The allowed radial load values Fr" in relation to a" are shown in the diagrams of each version equipped with cover with support bearings.
200 - P - 991218 - E - 00/06.02 6/104

2.6 General installation precautions
In addition to the recommendations regarding fluids, filtraĆ - To ensure the best heat distribution inside the tank, make
tion, coupling, etc., we suggest the following: sure the return pipe is not too close to the pump's suction
- Always check the rotation direction of the pump's drive piping.
shaft; it must be compatible with the rotation direction of the The pipings themselves should be below oil tank level to
pump itself. prevent the formation of foam.
- Be particularly careful in cleaning and make sure, when - Do not subject the pumps to operating conditions differĆ
connecting the suction and pressure piping, that no chips, ent from those indicated on p. 9/104; for extreme operations,
rag threads, teflon tape, etc. get into the pump circulation always contact our Technical Department.
system. - Never use fluids different from those indicated in section
- Check the tightness of the suction and pressure fittings, 2.2.
the correct positioning of the O-Ring, and make sure there - In the event of pump painting, do not use solvents or
is no dirt between the flange and the pump body. paints that are incompatible with the material of the seals.
- The first pump start-up can be facilitated by manually fillĆ Do not bake paint with excessively high temperatures.
ing the suction piping and the pump itself with oil. Do not paint over the product identification plate; the warĆ
To facilitate air bleeding, start the pump with the circuit not ranty will not be valid if this plate is illegible.
pressurised.
2.7 pressure p (bar)
Pressure levels: P3
AP05
P1 = continuous pressure P2
P2 = intermittent pressure APR05 P1
P3 = peak pressureThe recommended oil speed in the presĆ
sure pipes is: v = 2 to 5 m/s
The characteristic data of each pump is given in the tables p0.05 s max. 5 s t (s)
on the following pages.
p (bar)
AP100 P3
AP200 P2
AP300 P1
p0.05 s max. 15 s t (s)
pressure flow rate surging
Pump Z ∆Q%
Q (l/min)
AP05 13 13
AP100 12 15
Q%
Qmax.- Qmin.
AP200 10 16 100
Q%=
Qmax.
AP300 10 16
t (s)
200 - P - 991218 - E - 00/06.02 7/104

2.8 Calculating the specifications of a
gear pump
The following parameters are defined:
Vc = (cm3/r) pump displacement; Q
p
n = (r/min) no. of rpms of the drive shaft;
Q = (l/min) flow rate; M
p = (bar) operating pressure; n
M = (Nm) drive torque; Vc M
N = (kW) power;
N (M,n)
ηv = (%) volumetric efficiency;
ηm = (%) mechanical efficiency;
ηt = (%) total efficiency
Vc n 100000 Q 100000 Q
Q= ηv Vc = n=
100000 n ηv Vc ηv
Vc n p Qp N 6.12 ηt N 6120 ηt

N= N= p= p=
6120 ηt 6.12 ηt Q Vc n
N ηt = ηv ηm
M = 9555
n
Example
AP100/2.5 Vc= 2.5 cm3/r n= 1500 r/min p=200 bar ηv= 94% ηm= 87%
2.5 1500 ηt = 0.94 0.87 = 0.82 = 82%

Q= 94= 3.52 l/min.
100000
3.52 200 1.4

N= = 1.4 kW M = 9555 = 9 Nm
6.12 82 1500
AP05 Displacement Max. pressure n min. n max.
Cu. In. P1 P2 P3
Type cm3/rev P ≤ P1 P > P1 P ≤ P1 P > P1
P. R. bar P.S.I. bar P.S.I. bar P.S.I.
AP05/0.25 0.25 .015 170 2400 180 2600 200 2900 800 1000 6000 7000
AP05/0.5 0.5 .030 190 2700 210 3000 230 3300 650 800 6000 7000
AP05/0.75 0.75 .045 190 2700 210 3000 230 3300 650 800 6000 7000
AP05/0.9 0.9 .055 190 2700 210 3000 230 3300 650 800 6000 7000
AP05/1.2 1.2 .073 170 2400 180 2600 200 2900 550 700 5000 6000
AP05/1.6 1.6 .097 170 2400 180 2600 200 2900 550 700 5000 6000
APR05/0.25 0.25 .015 150 2200 160 2300 180 2600 800 1000 6000 7000
APR05/0.5 0.5 .030 170 2400 190 2700 210 3000 650 800 6000 7000
APR05/0.75 0.75 .045 170 2400 190 2700 210 3000 650 800 6000 7000
APR0.5/0.9 0.9 .055 170 2400 190 2700 210 3000 650 800 6000 7000
APR05/1.2 1.2 .073 150 2200 160 2300 180 2600 550 700 5000 6000
200 - P - 991218 - E - 00/06.02 8/104

Cu. In. P1 P2 P3
AP100/1.2 1.2 .073 210 3000 250 3600 280 4000 800 1000 4500 5000
AP100/1.7 1.7 .103 210 3000 250 3600 280 4000 650 800 4500 5000
AP100/2.5 2.5 .152 210 3000 250 3600 280 4000 650 800 4500 5000
AP100/3.5 3.5 .213 210 3000 230 3300 250 3600 650 800 3500 4000
AP100/4.3 4.3 .262 210 3000 230 3300 250 3600 550 700 3500 4000
AP100/5 5.0 .305 210 3000 230 3300 250 3600 500 650 3000 3500
AP100/6.5 6.5 .396 190 2700 220 3150 240 3400 500 650 2500 3000
AP100/8 7.8 .476 180 2600 210 3000 230 3300 500 650 2500 3000
AP100/10 10.0 .610 150 2150 180 2600 200 2900 500 650 2000 2500
P1 P2 P3
Cu. In.
P. R.
bar P.S.I. bar P.S.I. bar P.S.I.
AP200/4.5 4.3 .262 220 3150 250 3600 280 4000 800 1000 3500 4000
AP200/6.5 6.3 .384 220 3150 250 3600 280 4000 800 1000 3500 4000
AP200/8.5 8.3 .506 220 3150 250 3600 280 4000 800 1000 3500 4000
AP200/11 11.0 .671 210 3000 230 3300 250 3600 700 900 3500 4000
AP200/15 15.0 .915 210 3000 230 3300 250 3600 650 800 3500 4000
AP200/19 18.9 1.159 210 3000 230 3300 250 3600 650 800 3000 3500
AP200/22 21.9 1.342 200 2900 220 3150 240 3400 600 750 3000 3500
AP200/26 25.9 1.586 190 2700 210 3000 230 3300 600 750 2500 3000
Cu. In. P1 P2 P3
AP300/27 27.0 1.674 220 3150 250 3600 280 4000 600 800 3000 3500
AP300/31 31.0 1.891 220 3150 250 3600 280 4000 600 800 3000 3500
AP300/38 38.0 2.318 220 3150 250 3600 280 4000 600 800 2500 3000
AP300/45 45.0 2.745 200 2900 230 3300 260 3700 600 800 2500 3000
AP300/53 53.0 3.233 200 2900 230 3300 260 3700 600 800 2500 3000
AP300/63 63.0 3.843 180 2600 210 3000 240 3400 550 700 2500 3000
AP300/75 75.0 4.575 170 2400 190 2700 220 3150 550 700 2000 2500
AP300/93 93.0 5.673 150 2100 170 2400 200 2900 500 650 2000 2500
N.B.: Please contact our Sales Department if even one of the operating limits indicated in the tables above (temperature, pressure, rpm) is exceeded,
as well as in the case of two or more maximum values at the same time, or for applications with particularly heavy–duty cycles.
200 - P - 991218 - E - 00/06.02 9/104

2.9 Diagrams
Oil viscosity: 37 mm2/s

Oil temperature: 40° C
Q (l/min)
Q (l/min)
a
10
AP05 1.6 AP100
6 b 8
1.2
20 a = 30 bar a
a = 30 bar a
a 0.9 b = 250 bar f e
b = 200 bar 18 c = 230 bar
5 c = 230 bar 6.5
b d = 220 bar a
0.75 16 5 4.3
e = 210 bar
a a a
f = 180 bar d
4 14
c
c c
a 12 3.5
a
c a 2.5
0.5
3 10 c
b
8.0 1.7
a a
2 b
c
6.0 1.2
0.25 a
b
a 4.0
1
b
2.0
0 1000 2000 3000 4000 5000 6000 n (min-1 ) 0 1000 2000 3000 4000 n (min-1 )
Q (l/min)
Q (l/min)
AP200 AP300
26 22
65 195
a 93
a = 30 bar a a = 30 bar
19
60 b = 250 bar 180 b = 250 bar a
e d
c = 230 bar c = 230 bar 75
55 165 63
d = 220 bar a 15 d = 210 bar f
a a
e = 200 bar 150 e = 190 bar 53
50
d f = 170 bar a d
45 c 135
a
e 45
120 c
40 11
a a
35 105 38
c c 31
8.5 90 a 27
30 a
a b b
25 6.5 75
b a a
20 60 b
b
4.5
15 45
a
b 30
10
5 15
0 1000 2000 3000 n (min-1 ) 0 1000 2000 3000 n (min-1 )
200 - P - 991218 - E - 00/06.02 10/104

AP05
M (Nm)
N (kW)
1.6 1.6
n= 1000 (min-1)
1.2 0.9
4.50 1.2 0.30
0.75
3.75 0.9 0.25
0.75
3.00 0.20
0.5
2.25 0.15
0.5
1.50 0.10
0.25 0.25
0.75 0.05
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

N (kW)
N (kW)
n= 2000 (min-1) 1.6 n= 3000 (min-1) 1.6
1.2 0.9 1.2 0.9

0.60 0.90
0.75 0.75
0.50 0.75
0.40 0.60
0.5 0.5
0.30 0.45
0.20 0.30
0.25 0.25
0.10 0.15
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

N (kW)
N (kW)
n= 5000 (min-1) 1.6 n= 7000 (min-1) 1.6

1.2 0.9 1.2
1.50 3.0
0.75 0.9
1.25 2.5
0.75
1.00 2.0
0.5
0.75 1.5 0.5
0.50 1.0
0.25 0.25
0.25 0.5
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)
200 - P - 991218 - E - 00/06.02 11/104

AP100
M (Nm)
N (kW)
10 10 8
8
n= 1000 (min-1)
6.5 6.5
25 2.5
5 5
20 2.0
4.3 4.3
15 3.5 1.5 3.5
2.5 2.5
10 1.0
1.7 1.7
5 0.5
1.2 1.2
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

N (kW)
N (kW)
10 8 8
n= 2000 (min-1) n= 3000 (min-1)
6.5 6.5
5.0 7.5
5 5
4.0 6.0
4.3 4.3
3.0 3.5 4.5 3.5
2.5 2.5
2.0 3.0
1.7 1.7
1.0 1.5
1.2 1.2
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

N (kW)
N (kW)
n= 4000 (min-1) n= 5000 (min-1)

2.5
10.0 5.0
8.0 4.3 4.0

1.7
6.0 3.5 3.0
1.2
2.5
4.0 2.0
1.7
2.0 1.0
1.2
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)
200 - P - 991218 - E - 00/06.02 12/104

AP200
M (Nm)
N (kW)
26 26
22
22 n= 1000 (min-1)
19
75 19 7.5
15 15
60 6.0
45 11 4.5 11
8.5 8.5
30 3.0
6.5 6.5
15 4.3 1.5 4.5
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

N (kW)
N (kW)
26
26 22
n= 1500 (min-1) n= 2000 (min-1)
22
19
12.5 19 15.0
15
10.0 15 12.0
11
7.5 11 9.0
8.5
8.5
5.0 6.0
6.5
6.5
2.5 3.0 4.5
4.5
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

N (kW)
N (kW)
26
26 22
n= 3000 (min-1) n= 4000 (min-1)
22
19
25.0 19 30.0
15
20.0 15 24.0
15.0 18.0 11
11
8.5
8.5
10.0 12.0
6.5
6.5
5.0 6.0 4.5
4.5
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)
200 - P - 991218 - E - 00/06.02 13/104

AP300
M (Nm)
N (kW)
93
93
75 n= 1000 (min-1)
75
63
25 63
225 53
53
45
180 20 45
38 38
135 31 15
31
90 27 10 27
45 5
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

N (kW)
N (kW)
93
n= 1500 (min-1) n= 2000 (min-1)
75
50 50 63
93 53
75
40 63 40 45
53
38
30 45 30
38 31
20 31 20 27
27
10 10
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

N (kW)
N (kW)
n= 2500 (min-1) n= 3000 (min-1)

93
75 75 100
63 93
53 75
60 80 63
45 53
45 38 60 45
38
30 31 40 31
27 27
15 20
0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)
200 - P - 991218 - E - 00/06.02 14/104

2.10 Information about the medium level of
sound pressure given out.
Ambient noise: 38 dB(A)
1 m.
dB(A)
dB(A)
AP100 P=10 bar h

AP100 P=150 bar
h
g g
60 f 70
f
e d e
55 65 c
c
50 60
b
a a = AP100/1.2 d a = AP100/1.2
45 55 b b = AP100/1.7
b = AP100/1.7 a
c = AP100/2.5 c = AP100/2.5
40 d = AP100/3.5 50 d = AP100/3.5
e = AP100/4.3 e = AP100/4.3
f = AP100/5 f = AP100/5
35 45 g = AP100/6.5
g = AP100/6.5
h = AP100/8 h = AP100/8
500 1000 1500 2000 2500 n (min-1) 500 1000 1500 2000 2500 n (min-1)
dB(A)
dB(A)
h
AP200 P=10 bar AP200 P=150 bar h
f f
75 e 80 e
d
d
b
70 75
a g
b a
65 70
c
g
a = AP200/4.5 a = AP200/4.5
60 b = AP200/6.5 65 b = AP200/6.5
c
c = AP200/8.5 c = AP200/8.5
55 d = AP200/11 60 d = AP200/11
e = AP200/15 e = AP200/15
f = AP200/19 f = AP200/19
50 g = AP200/22 55 g = AP200/22
h = AP200/26 h = AP200/26
500 1000 1500 2000 2500 n (min-1) 500 1000 1500 2000 2500 n (min-1)
200 - P - 991218 - E - 00/06.02 15/104

3 Gear pumps group AP05

Cu.In. P1 P2 P3
P.R. bar P.S.I. bar P.S.I. bar P.S.I.
AP05/0.25 0.25 .015 170 2400 180 2600 200 2900 800 1000 6000 7000
AP05/0.5 0.5 .030 190 2700 210 3000 230 3300 650 800 6000 7000
AP05/0.75 0.75 .045 190 2700 210 3000 230 3300 650 800 6000 7000
AP05/0.9 0.9 .055 190 2700 210 3000 230 3300 650 800 6000 7000
AP05/1.2 1.2 .073 170 2400 180 2600 200 2900 550 700 5000 6000
AP05/1.6 1.6 .097 170 2400 180 2600 200 2900 550 700 5000 6000
APR05/0.25 0.25 .015 150 2200 160 2300 180 2600 800 1000 6000 7000
APR05/0.5 0.5 .030 170 2400 190 2700 210 3000 650 800 6000 7000
APR05/0.75 0.75 .045 170 2400 190 2700 210 3000 650 800 6000 7000
APR0.5/0.9 0.9 .055 170 2400 190 2700 210 3000 650 800 6000 7000
APR05/1.2 1.2 .073 150 2200 160 2300 180 2600 550 700 5000 6000
Max torque allowed to the shaft

7+1.5 Nm
M max= 13 Nm **9
5 Last number of pump code
M max= 5 Nm **0
Notes:
– For uses at the operating limits, see note on page 9/104.
– For codes and dimensions regarding accessories, see section 7.
– For the types of pumps without ordering code, contact our Sales Department.
200 - P - 991218 - E - 00/06.02 16/104

Group AP05 Code 810
1/4" BSPP Depth.11 -.43" ø7 DIN6888

Suction-Pressure .275" DIA
B 4
19
.866"-.864"DIA
25+5 Nm
.158"
M7
ø22 f8
1.004"
.295"
25.5
7.5
3.15"
2.047"
2.6"
80
52
66
11
6.5 12.5 10+2 Nm
.256" .49"
.307"-.3"
48 5 8 8
7.8 -0.2
0
1.89" .197" .315" .315" 2 h9
.079"-.078"
A 21
.827"
7 h6
.2756"-.2752"
Dimensions
Displacement
Type A B
cm3/rev
mm inch. mm inch.
AP05/0 25
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54 29 1 41
1.41
AP05/0 5
AP05/0.5 05
0.5 67 2 64
2.64 30 5
30.5 12
1.2
AP05/0 75
AP05/0.75 0 75
0.75 69 2 72
2.72 31 5
31.5 1 24
1.24
AP05/0 9
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77 32 1 26
1.26
AP05/1 2
AP05/1.2 12
1.2 73 2 87
2.87 33 5
33.5 1 32
1.32
Accessories
Clockwise C.clockwise Flange Splined

Type Order Code Type Order Code
rotation: D rotation: S connectors couplings
AP05/0.25 D 200.1002.612.04 AP05/0.25 S 200.1002.613.02 GSH-06
D S
AP05/0.5 D 200.1003.612.02 AP05/0.5 S 200.1003.613.02
AP05/0.75 D 200.1004.612.02 AP05/0.75 S 200.1004.613.02
AP05/0.9 D 200.1005.612.02 AP05/0.9 S 200.1005.613.02
AP05/1.2 D 200.1006.612.02 AP05/1.2 S 200.1006.613.02
200 - P - 991218 - E - 00/06.02 17/104

Group AP05 Code 819
1/4" BSPP Depth 11 -.43"

Suction-Pressure
B 4
.158"
19 25+5 Nm
.197"-.196"
.866"-.864" DIA
ø22 f8
5 f7
1.004"
25.5
.295"
7.5
2.047"
3.15"
2.6"
52
80
66
6.5 12.5 5.5

.256" .49" .216"
48 A 9.5
1.89" .374"
Dimensions
Displacement A B
Type
cm3/rev
mm inch. mm inch.
AP05/0 25
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54 29 1 41
1.41
AP05/0 5
AP05/0.5 05
0.5 67 2 64
2.64 30 5
30.5 12
1.2
AP05/0 75
AP05/0.75 0 75
0.75 69 2 72
2.72 31 5
31.5 1 24
1.24
AP05/0 9
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77 32 3
32.3 1 26
1.26
AP05/1 2
AP05/1.2 12
1.2 73 2 87
2.87 33 5
33.5 1 32
1.32
AP05/1 6
AP05/1.6 16
1.6 77 3 03
3.03 35 5
35.5 1 40
1.40
Clockwise C.clockwise
rotation: D rotation: S
AP05/0.25 D 200.1002.642.08 AP05/0.25 S 200.1002.643.04
AP05/0.5 D 200.1003.642.02 D AP05/0.5 S 200.1003.643.02 S
AP05/0.75 D 200.1004.642.02 AP05/0.75 S 200.1004.643.02

AP05/0.9 D 200.1005.642.04 AP05/0.9 S 200.1005.643.04
AP05/1.2 D 200.1006.642.02 AP05/1.2 S 200.1006.643.02
AP05/1.6 D 200.1008.642.02 AP05/1.6 S 200.1008.643.01
200 - P - 991218 - E - 00/06.02 18/104

Group AP05 Code 310
ø7 DIN6888
.275" DIA
Suction-Pressure
20+5 Nm
.866"-.864" DIA
ø22 f8
M7
1/4" BSPP
1.004"
25.5
19
2.047"
3.15"
2.6"
80
66
52
6.5 12.5 4 11
10+2 Nm 24
.256" .49" .158" .945"
48 5 8 8
1.89" .197" .315" .315"
A 21
.827"
.307"-.3"
2 h9
7.8 -0.2
0
.079"-.078"
7 h6
.2756"-.2752"
Dimensions
Displacement A
Type
cm3/rev
mm inch.
AP05/0 25
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54
AP05/0 5
AP05/0.5 05
0.5 67 2 64
2.64
AP05/0 75
AP05/0.75 0 75
0.75 69 2 72
2.72
AP05/0 9
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77
AP05/1 2
AP05/1.2 12
1.2 73 2 87
2.87
Accessories

AP05/0.25 D 200.1002.612.01 AP05/0.25 S 200.1002.613.01 GSH-06
D S
AP05/0.5 D 200.1003.612.01 AP05/0.5 S 200.1003.613.01
AP05/0.75 D 200.1004.612.01 AP05/0.75 S 200.1004.613.01
AP05/0.9 D 200.1005.612.01 AP05/0.9 S 200.1005.613.01
AP05/1.2 D 200.1006.612.01 AP05/1.2 S 200.1006.613.01
200 - P - 991218 - E - 00/06.02 19/104

Group AP05 Code 319
4 24
.866"-.864" DIA
.158" .945"
Suction-Pressure
20+5 Nm
.197"-.196"
ø22 f8
5 f7
1/4" BSPP
1.004"
.295"
25.5
7.5
19
2.047"
3.15"
2.6"
80
66
52
6.5 12.5 5.5

.256" .49" .216"
48 A 9.5
1.89" .374"
Dimensions
Displacement A
Type
cm3/rev
mm inch.
AP05/0 25
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54
AP05/0 5
AP05/0.5 05
0.5 67 2 64
2.64
AP05/0 75
AP05/0.75 0 75
0.75 69 2 72
2.72
AP05/0 9
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77
AP05/1 2
AP05/1.2 12
1.2 73 2 87
2.87
AP05/1 6
AP05/1.6 16
1.6 77 3 03
3.03
AP05/0.25 D 200.1002.142.02 AP05/0.25 S 200.1002.143.01
AP05/0.5 D 200.1003.142.01 D AP05/0.5 S 200.1003.143.01 S
AP05/0.75 D 200.1004.142.01 AP05/0.75 S 200.1004.143.01

AP05/0.9 D 200.1005.142.01 AP05/0.9 S 200.1005.143.01
AP05/1.2 D 200.1006.142.01 AP05/1.2 S 200.1006.143.01
AP05/1.6 D 200.1008.142.01 AP05/1.6 S 200.1008.143.01
200 - P - 991218 - E - 00/06.02 20/104

Group AP05 Code 410
ø7 DIN6888
16 .275" DIA
OR 2025
0.63"
Pressure
.866"-.864" DIA
20+5 Nm
M7
Suction
1/4" BSPP
ø22 f8
1.004"
25.5
19
3.15"
2.047"
2.6"
80
66
52
.29"
7.5
.197"
5
6.5 12.5 4 11
10+2 Nm 24
.256" .49" .158" .945"
48 5 8 8
1.89" .197" .315" .315"
A 21
.827"
.307"-.3"
2 h9
7.8 -0.2
0
.079"-.078"
7 h6
The drawing shows a pump with clockwise rotation.
.2756"-.2752"
Dimensions
Displacement A
Type
cm3/rev
mm inch.
AP05/0 25
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54
AP05/0 5
AP05/0.5 05
0.5 67 2 64
2.64
AP05/0 75
AP05/0.75 0 75
0.75 69 2 72
2.72
AP05/0 9
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77
AP05/1 2
AP05/1.2 12
1.2 73 2 87
2.87
Accessories

AP05/0.25 D AP05/0.25 S 200.1002.613.04 GSH-06
D S
AP05/0.5 D AP05/0.5 S 200.1003.613.04
AP05/0.75 D AP05/0.75 S
AP05/0.9 D 200.1005.612.04 AP05/0.9 S
AP05/1.2 D AP05/1.2 S
200 - P - 991218 - E - 00/06.02 21/104

Group AP05 Code 419
16 OR 2025 4 24
.866"-.864" DIA
Pressure .158" .945"
0.63"
20+5 Nm
.197"-.196"
Suction
1/4" BSPP
ø22 f8
5 f7
1.004"
.295"
25.5
7.5
19
3.15"
2.047"
2.6"
80
66
52
.29"
.197"
7.5
6.5 12.5 5.5

.256"
.49" .216"
48
1.89" A 9.5
.374"
Dimensions
Displacement A
Type
cm3/rev
mm inch.
AP05/0 25
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54
AP05/0 5
AP05/0.5 05
0.5 67 2 64
2.64
AP05/0 75
AP05/0.75 0 75
0.75 69 2 72
2.72
AP05/0 9
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77
AP05/1 2
AP05/1.2 12
1.2 73 2 87
2.87
AP05/1 6
AP05/1.6 16
1.6 77 3 03
3.03
AP05/0.25 D AP05/0.25 S
AP05/0.5 D 200.1003.642.03 D AP05/0.5 S 200.1003.643.04 S
AP05/0.75 D AP05/0.75 S 200.1004.643.03

AP05/0.9 D AP05/0.9 S
AP05/1.2 D AP05/1.2 S
AP05/1.6 D AP05/1.6 S 200.1008.643.02
200 - P - 991218 - E - 00/06.02 22/104

Group AP05 Code 830
1/4" BSPP Depth 11 - .43" ø7 DIN6888
.866"-.864" DIA
B 4
19 25+5 Nm
M7
.158"
ø22 f8
X
.295"
7.5
.295"
7.5
2.047"
1.182"
52
30
5.5
.216"
32 C 48
1.26" 11 1.89"
10+2 Nm
5 8 8
X
.197" .315" .315"
A 21
.827"
.307"-.3"
7.8 -0.2
0
2 h9
R 6.5
.079"-.078"
.256"
To utilize M5x0.8 DIN912

7 h6
.2756"-.2752" 4 7+1.5 Nm
Dimensions
Displacement A B C
Type
cm3/rev
mm inch. mm inch. mm inch.
AP05/0 25
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54 29 1 41
1.41 53 5
53.5 2 11
2.11
AP05/0 5
AP05/0.5 05
0.5 67 2 64
2.64 30 5
30.5 12
1.2 56 2 20
2.20
AP05/0 75
AP05/0.75 0 75
0.75 69 2 72
2.72 31 5
31.5 1 24
1.24 58 2 28
2.28
AP05/0 9
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77 32 1 26
1.26 59 5
59.5 2 34
2.34
AP05/1 2
AP05/1.2 12
1.2 73 2 87
2.87 33 5
33.5 1 32
1.32 62 2 44
2.44
Accessories

AP05/0.25 D 200.1002.302.01 AP05/0.25 S 200.1002.303.01 GSH-06
D S
AP05/0.5 D AP05/0.5 S 200.1003.303.01
AP05/0.75 D AP05/0.75 S
AP05/0.9 D AP05/0.9 S
AP05/1.2 D AP05/1.2 S 200.1006.313.01
200 - P - 991218 - E - 00/06.02 23/104

Group AP05 Code 839
1/4" BSPP Depth 11 - .43"
Suction-Pressure
19 25+5 Nm B 4
.866"-.864" DIA
.197"-.196"
.158" X
ø22 f8
5 f7
.295"
7.5
.295"
7.5
1.182"
2.047"
52
30
5.5
32 C 5.5 .216" 48
1.26" .216" 1.89"
A 9.5 X
.374"
R 6.5
.256"
4 7+1.5 Nm
Dimensions
Displacement A B C
Type
cm3/rev
mm. inch. mm inch. mm inch.
AP05/0 25
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54 29 1 41
1.41 53 5
53.5 2 11
2.11
AP05/0 5
AP05/0.5 05
0.5 67 2 64
2.64 30 5
30.5 12
1.2 56 2 20
2.20
AP05/0 75
AP05/0.75 0 75
0.75 69 2 72
2.72 31 5
31.5 1 24
1.24 58 2 28
2.28
AP05/0 9
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77 32 1 26
1.26 59 5
59.5 2 34
2.34
AP05/1 2
AP05/1.2 12
1.2 73 2 87
2.87 33 5
33.5 1 32
1.32 62 2 44
2.44
AP05/1 6
AP05/1.6 16
1.6 77 3 03
3.03 35 5
35.5 1 40
1.40 66 2 60
2.60
AP05/0.25 D AP05/0.25 S
AP05/0.5 D 200.1003.342.01 D AP05/0.5 S S
AP05/0.75 D 200.1004.342.01 AP05/0.75 S 200.1004.343.04

AP05/0.9 D 200.1005.342.01 AP05/0.9 S 200.1005.343.02
AP05/1.2 D 200.1006.342.04 AP05/1.2 S 200.1006.343.01
AP05/1.6 D 200.1008.342.01 AP05/1.6 S 200.1008.343.01
200 - P - 991218 - E - 00/06.02 24/104

Group AP05 Code 330
ø7 DIN6888
.275" DIA
Suction-Pressure
20+5 Nm
.866"-.864" DIA
A 4 X
M7
.158"
ø22 f8
1/4" BSPP
.295"
7.5
19
1.182"
2.047"
30
52
5.5
32 5 8 8 .216"
1.26" .197" .315" .315" 24
11
10+2 Nm .945"
48 B 21
1.89" .827"
X
.307"-.3"
7.8 -0.2
0
2 h9
.079"-.078" R 6.5
.256"
7 h6 To utilize M5x0.8 DIN912

.2756"-.2752" 4 7+1.5 Nm
Dimensions
Displacement A B
Type
cm3/rev
mm inch. mm inch.
AP05/0 25
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54 53 5
53.5 2 11
2.11
AP05/0 5
AP05/0.5 05
0.5 67 2 64
2.64 56 2 20
2.20
AP05/0 75
AP05/0.75 0 75
0.75 69 2 72
2.72 58 2 28
2.28
AP05/0 9
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77 59 5
59.5 2 34
2.34
AP05/1 2
AP05/1.2 12
1.2 73 2 87
2.87 62 2 44
2.44
Accessories

AP05/0.25 D AP05/0.25 S GSH-06
D S
AP05/0.5 D AP05/0.5 S
AP05/0.75 D AP05/0.75 S
AP05/0.9 D 200.1005.312.01 AP05/0.9 S
AP05/1.2 D AP05/1.2 S
200 - P - 991218 - E - 00/06.02 25/104

Group AP05 Code 339
Suction-Pressure
.197"-.196"
A 4
1/4" BSPP
X
.866"-.864" DIA
20+5 Nm
.157"
ø22 f8
5 f7
.295"
7.5
1.182"
2.047"
19
30
52
5.5
32 5.5 .216" 24
1.26" .216" .945"
B 9.5 X
48
1.89" .374"
R 6.5
.256"
4 7+1.5 Nm
Dimensions
Displacement A B
Type
cm3/rev
mm inch. mm inch.
AP05/0 25
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54 53 5
53.5 2 11
2.11
AP05/0 5
AP05/0.5 05
0.5 67 2 64
2.64 56 2 20
2.20
AP05/0 75
AP05/0.75 0 75
0.75 69 2 72
2.72 58 2 28
2.28
AP05/0 9
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77 59 5
59.5 2 34
2.34
AP05/1 2
AP05/1.2 12
1.2 73 2 87
2.87 62 2 44
2.44
AP05/1 6
AP05/1.6 16
1.6 77 3 03
3.03 66 2 60
2.60
AP05/0.25 D 200.1002.342.01 AP05/0.25 S 200.1002.343.03
AP05/0.5 D 200.1003.342.03 D AP05/0.5 S 200.1003.343.03 S
AP05/0.75 D 200.1004.342.02 AP05/0.75 S 200.1004.343.02

AP05/0.9 D 200.1005.342.03 AP05/0.9 S 200.1005.343.03
AP05/1.2 D 200.1006.342.03 AP05/1.2 S 200.1006.343.03
AP05/1.6 D 200.1008.342.02 AP05/1.6 S 200.1008.343.02
200 - P - 991218 - E - 00/06.02 26/104

Group AP05 Code 430
OR 2025
Pressure ø7 DIN6888
.275" DIA
16 A 4
.63" .158" X
.866"-.864"DIA
20+5 Nm
1/4" BSPP
M7
Suction
ø22 f8
.295"
7,5
2.047"
1.182"
19
30
52
.197"
.295"
7,5
5
5,5
.216"
24
32 5 8 8
.945"
1.26" .197" .315" .315" 11
10+2 Nm X
48 B 21
1.89" .827"
.307"-.3"
7.8 -0.2
0
2 h9
.079"-.078"
R 6.5
.256"
7 h6 To utilize M5x0.8 DIN912

The drawing shows a pump with clockwise rotation. .2756"-.2752"
4 7+1.5 Nm
Dimensions
Displacement A B
Type
cm3/rev
mm inch. mm inch.
AP05/0 25 D
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54 53 5
53.5 2 11
2.11
AP05/0 5 D
AP05/0.5 05
0.5 67 2 64
2.64 56 2 20
2.20
AP05/0 75 D
AP05/0.75 0 75
0.75 69 2 72
2.72 58 2 28
2.28
AP05/0 9 D
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77 59 5
59.5 2 34
2.34
AP05/1 2 D
AP05/1.2 12
1.2 73 2 87
2.87 62 2 44
2.44
Accessories

AP05/0.25 D AP05/0.25 S GSH-06
D S
AP05/0.5 D AP05/0.5 S
AP05/0.75 D AP05/0.75 S
AP05/0.9 D AP05/0.9 S
AP05/1.2 D AP05/1.2 S
200 - P - 991218 - E - 00/06.02 27/104

Group AP05 Code 439
OR 2025
Pressure
16 A 4
1/4" BSPP
X
.197"-.196"
.866"-.864"DIA
.63"
Suction
20+5 Nm
.157"
ø22 f8
5 f7
.295"
7,5
2.047"
1.182"
19
30
52
.295"
.197"
7,5
5
5,5
.216"
5.5 24
32
.945" X
1.26" .216"
48 B 9,5
1.89"
.374"
R 6.5
.256"
4 7+1.5 Nm
Dimensions
Displacement A B
Type
cm3/rev
mm inch. mm inch.
AP05/0 25 D
AP05/0.25 0 25
0.25 64 5
64.5 2 54
2.54 53 5
53.5 2 11
2.11
AP05/0 5 D
AP05/0.5 05
0.5 67 2 64
2.64 56 2 20
2.20
AP05/0 75 D
AP05/0.75 0 75
0.75 69 2 72
2.72 58 2 28
2.28
AP05/0 9 D
AP05/0.9 09
0.9 70 5
70.5 2 77
2.77 59 5
59.5 2 34
2.34
AP05/1 2 D
AP05/1.2 12
1.2 73 2 87
2.87 62 2 44
2.44
AP05/1 6 D
AP05/1.6 16
1.6 77 3 03
3.03 66 2 60
2.60
AP05/0.25 D 200.1002.342.02 AP05/0.25 S 200.1002.343.02
AP05/0.5 D 200.1003.342.02 D AP05/0.5 S 200.1003.343.02 S
AP05/0.75 D AP05/0.75 S 200.1004.343.03

AP05/0.9 D 200.1005.342.02 AP05/0.9 S
AP05/1.2 D 200.1006.342.02 AP05/1.2 S
AP05/1.6 D AP05/1.6 S
200 - P - 991218 - E - 00/06.02 28/104

Group APR05 Code 810
1/4" BSPP Depth 11 - .43" ø7 DIN6888

B 4
19 25+5 Nm
.866"-.864"DIA
.158"
ø22 f8
M7
1.004"
.295"
25.5
7.5
2.047"
3.15"
2.6"
80
52
66
.551"
14
11 10+2 Nm
6.5 9 12.5
.256" .354" 1/8" BSPP Drain
.49"
48 5 8 8 14 8.5+1 Nm
1.89" .197" .315" .315"
.307"-.3"
7.8 -0.2
A 21
0
2 h9
.827"
.079"-.078"
Reversible gear pump 7 h6

.2756"-.2752"
Dimensions
Displacement
Di l t
Type A B
cm3/rev
mm inch. mm inch.
APR05/0 25
APR05/0.25 0 25
0.25 64 5
64.5 2 54
2.54 29 1 41
1.41
APR05/0 5
APR05/0.5 05
0.5 67 2 64
2.64 30 5
30.5 1 20
1.20
APR05/0 75
APR05/0.75 0 75
0.75 69 2 72
2.72 31 5
31.5 1 94
1.94
APR05/0 9
APR05/0.9 09
0.9 70 5
70.5 2 77
2.77 32 3
32.3 1 26
1.26
APR05/1 2
APR05/1.2 12
1.2 73 2 87
2.87 33 5
33.5 1 32
1.32
Accessories
Reversible Flange Splined

Type Order Code
gear pump: R connectors couplings
APR05/0.25 200.1002.611.01 R
GSH-06
APR05/0.5 200.1003.611.01
APR05/0.75 200.1004.611.01
APR05/0.9 200.1005.611.01
APR05/1.2 200.1006.611.01
200 - P - 991218 - E - 00/06.02 29/104

Cu.In. P1 P2 P3
AP100/1.2 1.2 .073 210 3000 250 3600 280 4000 800 1000 4500 5000
AP100/1.7 1.7 .103 210 3000 250 3600 280 4000 650 800 4500 5000
AP100/2.5 2.5 .152 210 3000 250 3600 280 4000 650 800 4500 5000
AP100/3.5 3.5 .213 210 3000 230 3300 250 3600 650 800 3500 4000
AP100/4.3 4.3 .262 210 3000 230 3300 250 3600 550 700 3500 4000
AP100/5 5 .305 210 3000 230 3300 250 3600 500 650 3000 3500
AP100/6.5 6.5 .396 190 2700 220 3150 240 3400 500 650 2500 3000
AP100/8 7.8 .476 180 2600 210 3000 230 3300 500 650 2500 3000
AP100/10 10 .610 150 2150 180 2600 200 2900 500 650 2000 2500
M max= 25 Nm **9 M max= 30 Nm **9

5 8
20+5 Nm
1:5 M max= 40 Nm **5 1:8 M max= 33 Nm **8
M max= 40 Nm **7
SAE J 498-9T 20/40 DP
M max= 27 Nm **0
Last number of pump code
Notes:
200 - P - 991218 - E - 00/06.02 30/104

Group AP100 Code 218
ø13 200.6612.0002.0
A .50" DIA
68
2.677" B
1.031"
52.4 16 65
.999"-997" DIA
26.2
ø 25.4 f8
2.063" .630" 2.560"
M7
1.279"
32.5
.433"
11
3.425"
2.830"
2.874"
71.9
87
73
.368" DIA
Taper 1:8
7.1 12 4
.28" .472" .157"
ø 9.35
M6 Depth 13 - .50" 11
10+2 Nm
30 9.6
1.181" .378" h8 (.0945"-.0939")
2.4 P9 (.0941"-.0931")
.220"-.216"
5.6 -0.1
Suction-Pressure 20.2 9
0
.795" .354"
Dimensions
Displacement
Di l t
Type A B
cm3/rev
mm inch. mm inch.
AP100/1 2
AP100/1.2 12
1.2 82 5
82.5 3 25
3.25 38 5
38.5 1 51
1.51
AP100/1 7
AP100/1.7 17
1.7 84 5
84.5 3 33
3.33 39 5
39.5 1 55
1.55
AP100/2 5
AP100/2.5 25
2.5 88 3 46
3.46 41 1 61
1.61
AP100/3 5
AP100/3.5 35
3.5 92 3 62
3.62 43 5
43.5 1 71
1.71
AP100/4 3
AP100/4.3 43
4.3 96 3 78
3.78 45 1 77
1.77
AP100/5 5 98 5
98.5 3 88
3.88 46 5
46.5 1 83
1.83
AP100/6 5
AP100/6.5 65
6.5 103 5
103.5 4 07
4.07 49 1 93
1.93
AP100/8 78
7.8 109 4 29
4.29 52 2 05
2.05
Accessories

AP100/1.2 D 200.1011.132.04 AP100/1.2 S 200.1011.133.04 RF197 GSH-1-12
AP100/1.7 D 200.1012.132.03 AP100/1.7 S 200.1012.133.04 RF198 GSH-1-14
D S
AP100/2.5 D 200.1013.132.03 AP100/2.5 S 200.1013.133.03 RF199
AP100/3.5 D 200.1014.132.04 AP100/3.5 S 200.1014.133.03
AP100/4.3 D 200.1015.132.03 AP100/4.3 S 200.1015.133.02
AP100/5 D 200.1016.132.03 AP100/5 S 200.1016.133.06
AP100/6.5 D 200.1017.132.03 AP100/6.5 S 200.1017.133.03
AP100/8 D 200.1018.132.02 AP100/8 S 200.1018.133.02
200 - P - 991218 - E - 00/06.02 31/104

A 4
68 .157"
2.677" B
.999"-.998"DIA
-0.020
ø 25.4 -0.053
52.4 16 65
.313"-.312"
2.063"
.630" 2.560"
-0.040
8 -0.076
.866"DIA
.472"DIA
ø 12
ø 22
1.279"
1.031"
32.5
26.2
.433"
11
2.874"
2.830"
3.425"
71.9
87
73
7.1 12 4.5 ± 0.15
.28" .472" .183"-.171"
30 6.5
M6 Depth 13 - .50"
1.181" .256"
Suction-Pressure
Dimensions
Displacement
Di l t
Type A B
cm3/rev
mm inch. mm inch.
AP100/1 2
AP100/1.2 12
1.2 82 5
82.5 3 25
3.25 38 5
38.5 1 51
1.51
AP100/1 7
AP100/1.7 17
1.7 84 5
84.5 3 33
3.33 39 5
39.5 1 55
1.55
AP100/2 5
AP100/2.5 25
2.5 88 3 46
3.46 41 1 61
1.61
AP100/3 5
AP100/3.5 35
3.5 92 3 62
3.62 43 5
43.5 1 71
1.71
AP100/4 3
AP100/4.3 43
4.3 96 3 78
3.78 45 1 77
1.77
AP100/5 5 98 5
98.5 3 88
3.88 46 5
46.5 1 83
1.83
AP100/6 5
AP100/6.5 65
6.5 103 5
103.5 4 07
4.07 49 1 93
1.93
AP100/8 78
7.8 109 4 29
4.29 52 2 05
2.05
AP100/10 10 118 4 64
4.64 56 5
56.5 2 22
2.22
Accessories
AP100/1.2 D AP100/1.2 S 200.1011.143.06 RF197
AP100/1.7 D AP100/1.7 S 200.1012.143.07 RF198
AP100/2.5 D D AP100/2.5 S 200.1013.143.06 S RF199
AP100/3.5 D AP100/3.5 S 200.1014.143.06
AP100/4.3 D AP100/4.3 S 200.1015.143.06
AP100/5 D AP100/5 S 200.1016.143.04
AP100/6.5 D AP100/6.5 S 200.1017.143.04
AP100/8 D AP100/8 S 200.1018.143.02
AP100/10 D AP100/10 S
200 - P - 991218 - E - 00/06.02 32/104

ø13 200.6612.0002.0
52.4 A 67
2.063" .50" DIA 2.560"
16
.999"-.997" DIA
30
ø 25.4 f8
1.031"
26.2 .630" 1.181"
M7
1.279"
32.5
2.874"
3.425"
2.830"
71.9
73
87
.433"
11
.368" DIA
3/8" BSPP Depth 12 - .47"
50+5 Nm
Taper 1:8
4
Suction-Pressure
7.1
.28" .157"
ø 9.35
11
68 10+2 Nm
9.6
2.677"
22
.378"
20.2 9
.220"-.216"
.795" .354" 2.4
5.6 -0.1
h8 (.0945"-.0939")
0
P9 (.0941"-.0931")
Dimensions
Displacement
Di l t
Type A
cm3/rev
mm inch.
AP100/1 2
AP100/1.2 12
1.2 82 5
82.5 3 25
3.25
AP100/1 7
AP100/1.7 17
1.7 84 5
84.5 3 33
3.33
AP100/2 5
AP100/2.5 25
2.5 88 3 46
3.46
AP100/3 5
AP100/3.5 35
3.5 92 3 62
3.62
AP100/4 3
AP100/4.3 43
4.3 96 3 78
3.78
AP100/5 5 98 5
98.5 3 88
3.88
AP100/6 5
AP100/6.5 65
6.5 103 5
103.5 4 07
4.07
AP100/8 78
7.8 109 4 29
4.29
Accessories

AP100/1.2 D 200.1011.132.05 AP100/1.2 S 200.1011.133.05 GSH-1-12
AP100/1.7 D 200.1012.132.04 AP100/1.7 S 200.1012.133.05 GSH-1-14
D S
AP100/2.5 D 200.1013.132.04 AP100/2.5 S 200.1013.133.04
AP100/3.5 D 200.1014.132.05 AP100/3.5 S 200.1014.133.04
AP100/4.3 D 200.1015.132.04 AP100/4.3 S 200.1015.133.05
AP100/5 D 200.1016.132.04 AP100/5 S 200.1016.133.07
AP100/6.5 D 200.1017.132.04 AP100/6.5 S 200.1017.133.04
AP100/8 D 200.1018.132.03 AP100/8 S 200.1018.133.03
200 - P - 991218 - E - 00/06.02 33/104

A 4
52.4 67
.157"
2.063" 2.560"
.999"-.998" DIA
30
-0.020
ø 25.4 -0.053
16
.313"-.312"
1.181"
1.031"
26.2
.630"
.472" DIA
-0.040
8 -0.076
.866" DIA
ø 12
ø 22
1.279"
32.5
.433"
2.830"
2.874"
3.425"
11
71.9
73
87
Suction-Pressure
50+5 Nm
7.1 4.5
3/8" BSPP
.28" .183"-.171"
68 6.5
2.677"
22
.256"
Dimensions
Displacement
Di l t
Type A
cm3/rev
mm inch.
AP100/1 2
AP100/1.2 12
1.2 82 5
82.5 3 25
3.25
AP100/1 7
AP100/1.7 17
1.7 84 5
84.5 3 33
3.33
AP100/2 5
AP100/2.5 25
2.5 88 3 46
3.46
AP100/3 5
AP100/3.5 35
3.5 92 3 62
3.62
AP100/4 3
AP100/4.3 43
4.3 96 3 78
3.78
AP100/5 5 98 5
98.5 3 88
3.88
AP100/6 5
AP100/6.5 65
6.5 103 5
103.5 4 07
4.07
AP100/8 78
7.8 109 4 29
4.29
AP100/10 10 118 4 64
4.64
AP100/1.2 D AP100/1.2 S 200.1011.143.07
AP100/1.7 D AP100/1.7 S 200.1012.143.08
AP100/2.5 D D AP100/2.5 S 200.1013.143.07 S
AP100/3.5 D 200.1014.142.01 AP100/3.5 S 200.1014.143.07
AP100/4.3 D AP100/4.3 S 200.1015.143.08
AP100/5 D 200.1016.142.01 AP100/5 S 200.1016.143.05
AP100/6.5 D 200.1017.142.02 AP100/6.5 S 200.1017.143.05
AP100/8 D AP100/8 S 200.1018.143.03
AP100/10 D AP100/10 S
200 - P - 991218 - E - 00/06.02 34/104

A
68 ø13 200.6612.0002.0
2.677" B
.50" DIA
65
1.031"
.999"-.997" DIA
52.4 26.2 16 2.560"
ø 25.4 f8
2.063" .630"
M7
1.279"
32.5
11
.433"
3.425"
2.874"
2.830"
71.9
87
73
ø 9.35 .368" DIA
Taper 1:8
7.1 4
.28" .157"
11
10+2 Nm
3/8" BSPP Depth 13 - .50" 9.6
Suction-Pressure .378"
2.4 h8 (.0945"-.0939")
.220"-.216"
20.2 9
5.6 -0.1
P9 (.0941"-.0931")
0
22 50+5 Nm .795" .354"
Dimensions
Displacement
Di l t
Type A B
cm3/rev
mm inch. mm inch.
AP100/1 2
AP100/1.2 12
1.2 82 5
82.5 3 25
3.25 38 5
38.5 1 51
1.51
AP100/1 7
AP100/1.7 17
1.7 84 5
84.5 3 33
3.33 39 5
39.5 1 55
1.55
AP100/2 5
AP100/2.5 25
2.5 88 3 46
3.46 41 1 61
1.61
AP100/3 5
AP100/3.5 35
3.5 92 3 62
3.62 43 5
43.5 1 71
1.71
AP100/4 3
AP100/4.3 43
4.3 96 3 78
3.78 45 1 77
1.77
AP100/5 5 98 5
98.5 3 88
3.88 46 5
46.5 1 83
1.83
AP100/6 5
AP100/6.5 65
6.5 103 5
103.5 4 07
4.07 49 1 93
1.93
AP100/8 78
7.8 109 4 29
4.29 52 2 05
2.05
Accessories

AP100/1.2 D 200.1011.132.07 AP100/1.2 S 200.1011.133.06 GSH-1-12
AP100/1.7 D 200.1012.132.05 AP100/1.7 S 200.1012.133.07 GSH-1-14
D S
AP100/2.5 D 200.1013.132.07 AP100/2.5 S 200.1013.133.05
AP100/3.5 D 200.1014.132.06 AP100/3.5 S 200.1014.133.06
AP100/4.3 D 200.1015.132.06 AP100/4.3 S 200.1015.133.04
AP100/5 D 200.1016.132.05 AP100/5 S 200.1016.133.09
AP100/6.5 D 200.1017.132.05 AP100/6.5 S 200.1017.133.05
AP100/8 D 200.1018.132.04 AP100/8 S 200.1018.133.04
200 - P - 991218 - E - 00/06.02 35/104

A 26
1.023"
40 B 18 8
.409"-.401"
0.1
10.3 0.1
ø7 DIN6888
1.579"-1.571" .708" .315" .275" DIA
7
.275"
M6
.334"-.326"
11
.433"
8,5 -0.2
1.579"-1.571"
1.26" DIA
0
ø32
40 0.1
2.874"
73
ø10 .393" DIA
Taper 1:5
X
67 C 8
2.64" .315"
10
10+2 Nm
Suction M18x1.5 h9 (.079"-.077")

27 55+10 Nm
.212"-.208"
2 P9 (.078"-.077")
5.4 -0.1
0
Pressure M14x1.5 22 30+10 Nm

To utilize M8 DIN931
13 20+5 Nm
Dimensions
Displacement
Di l t
Type A B C
cm3/rev
AP100/1 2
AP100/1.2 12
1.2 73 5
73.5 2 89
2.89 36 5
36.5 1 44
1.44 70 2 75
2.75
AP100/1 7
AP100/1.7 17
1.7 75 5
75.5 2 97
2.97 37 5
37.5 1 48
1.48 72 2 83
2.83
AP100/2 5
AP100/2.5 25
2.5 79 2 99
2.99 39 1 53
1.53 75 5
75.5 2 97
2.97
AP100/3 5
AP100/3.5 35
3.5 83 3 27
3.27 41 1 61
1.61 80 3 15
3.15
AP100/4 3
AP100/4.3 43
4.3 87 3 42
3.42 43 1 69
1.69 83 5
83.5 3 29
3.29
AP100/5 5 89 5
89.5 3 52
3.52 44 5
44.5 1 75
1.75 86 3 38
3.38
AP100/6 5
AP100/6.5 65
6.5 94 5
94.5 3 72
3.72 47 1 85
1.85 91 3 58
3.58
AP100/8 78
7.8 100 3 98
3.98 50 1 97
1.97 97 3 81
3.81
Accessories

AP100/1.2 D 200.1011.422.02 AP100/1.2 S 200.1011.423.02 GSH-1B-12
AP100/1.7 D 200.1012.422.01 AP100/1.7 S 200.1012.423.01
D S
AP100/2.5 D 200.1013.422.01 AP100/2.5 S 200.1013.423.01
AP100/3.5 D 200.1014.422.01 AP100/3.5 S 200.1014.423.01
AP100/4.3 D 200.1015.422.01 AP100/4.3 S 200.1015.423.01
AP100/5 D 200.1016.422.01 AP100/5 S 200.1016.423.01
AP100/6.5 D 200.1017.422.01 AP100/6.5 S 200.1017.423.01
AP100/8 D 200.1018.422.01 AP100/8 S 200.1018.423.01
200 - P - 991218 - E - 00/06.02 36/104

67 A
2.64" OR 2112
B
1.258"-1.257" DIA
.409"-.401"
.334"-.326" 10.3 0.1 0,4
32 -0.025
-0.064
40 0.1 .015"
.944" DIA
1.578"-1.571" 7
ø 24
.275"
X
8,5 -0.2
1.578"-1.571"
.433"
11
0
2.874"
40 0.1
73
.195"-.193"
-0.040
5 -0.090
X
X
Suction M18x1.5 2.5 2 To utilize
27 55+10 Nm
.098" .078" M8 DIN931
Pressure M14x1.5 C 13 20+5 Nm
22
30+10 Nm
1.260"-1.259" DIA
Pump side Joint +0.2 Coupling side
8 0
+0.024
ø 32 -0.015
.323"-.314"
.472" DIA
X-X
ø 12
+0.1
4.8 0
.195"-.193"
.905"DIA
-0.040
5 -0.090
ø 23
Max pressure (M max= 25 Nm) .039" .192"-.189"

P bar (PSI) X
Pump
P1 P2 P3
160 180 200 M
AP100/6.5 (2300) (2600) (2900)
130 150 170 X

AP100/8 8.5 0.2-0.1
(1900) (2100) (2400) .334" .007"-.004"
Dimensions
Displacement
Di l t
Type A B C
cm3/rev
AP100/1 2
AP100/1.2 12
1.2 82 5
82.5 3 25
3.25 38 5
38.5 1 51
1.51 70 2 75
2.75
AP100/1 7
AP100/1.7 17
1.7 84 5
84.5 3 33
3.33 39 5
39.5 1 55
1.55 72 2 83
2.83
AP100/2 5
AP100/2.5 25
2.5 88 3 46
3.46 41 1 61
1.61 75 5
75.5 2 97
2.97
AP100/3 5
AP100/3.5 35
3.5 92 3 62
3.62 43 5
43.5 1 71
1.71 80 3 15
3.15
AP100/4 3
AP100/4.3 43
4.3 96 3 78
3.78 45 1 77
1.77 83 5
83.5 3 29
3.29
AP100/5 5 98 5
98.5 3 88
3.88 46 5
46.5 1 83
1.83 86 3 38
3.38
AP100/6 5
AP100/6.5 65
6.5 103 5
103.5 4 07
4.07 49 1 93
1.93 91 3 58
3.58
AP100/8 78
7.8 109 4 29
4.29 52 2 05
2.05 97 3 81
3.81
AP100/1.2 D 200.1011.442.01 AP100/1.2 S 200.1011.443.03
AP100/1.7 D 200.1012.442.02 AP100/1.7 S 200.1012.443.03
D S
AP100/2.5 D 200.1013.442.03 AP100/2.5 S 200.1013.443.03
AP100/3.5 D 200.1014.442.01 AP100/3.5 S 200.1014.443.03
AP100/4.3 D 200.1015.442.01 AP100/4.3 S 200.1015.443.03
AP100/5 D 200.1016.442.01 AP100/5 S 200.1016.443.01
AP100/6.5 D 200.1017.442.01 AP100/6.5 S 200.1017.443.02
AP100/8 D 200.1018.442.01 AP100/8 S 200.1018.443.04
N.B.: With respect to the standards, the maximum pressures of some versions of this pump are reduced in relation to the max. torque allowed to the shaft.
200 - P - 991218 - E - 00/06.02 37/104

Group AP100 Code 849P
67 A
2.64" OR 2112
B
.409"-.401"
1.258"-1.257" DIA
10.3 0.1 0,4
-0.025
32 -0.064
40 0.1 .015"
.944"DIA
1.578"-1.571" 7
ø 24
.275"
X
.334"-.326"
8,5 -0.2
1.578"-1.571"
.433"
11
0
40 0.1
2.874"
73
.195"-.193"
X
-0.040
5 -0.090
X
2.5 2 To utilize
Suction M18x1.5 27 55+10 Nm
.098" .078" M8 DIN931
C
Pressure M14x1.5 13 20+5 Nm
22 30+10 Nm
+0.2
Pump side Joint 8 0 Coupling side
1.260"-1.259" DIA
+0.024
ø 32 -0.015
.195"-.193"
.323"-.314"
.472" DIA
X-X
ø 12
+0.1
4.8 0
-0.040
5 -0.090
.905"DIA
1
ø 23
.039" .192"-.189"
Max pressure (M max= 25 Nm)
bar (PSI) X
Pump
P1 P2 P3
M
160 180 200
AP100/6.5 (2300) (2600) (2900)
130 150 170 X

AP100/8 8.5 0.2-0.1
(1900) (2100) (2400) .334" .007"-.004"
Dimensions
Displacement
Di l t
Type A B C
cm3/rev
AP100/1 2
AP100/1.2 12
1.2 82 5
82.5 3 25
3.25 38 5
38.5 1 51
1.51 70 2 75
2.75
AP100/1 7
AP100/1.7 17
1.7 84 5
84.5 3 33
3.33 39 5
39.5 1 55
1.55 72 2 83
2.83
AP100/2 5
AP100/2.5 25
2.5 88 3 46
3.46 41 1 61
1.61 75 5
75.5 2 97
2.97
AP100/3 5
AP100/3.5 35
3.5 92 3 62
3.62 43 5
43.5 1 71
1.71 80 3 15
3.15
AP100/4 3
AP100/4.3 43
4.3 96 3 78
3.78 45 1 77
1.77 83 5
83.5 3 29
3.29
AP100/5 5 98 5
98.5 3 88
3.88 46 5
46.5 1 83
1.83 86 3 38
3.38
AP100/6 5
AP100/6.5 65
6.5 103 5
103.5 4 07
4.07 49 1 93
1.93 91 3 58
3.58
AP100/8 78
7.8 109 4 29
4.29 52 2 05
2.05 97 3 81
3.81
AP100/1.2 D 200.1011.442.02 AP100/1.2 S 200.1011.443.04
AP100/1.7 D 200.1012.442.03 AP100/1.7 S 200.1012.443.04
D S
AP100/2.5 D 200.1013.442.04 AP100/2.5 S 200.1013.443.04
AP100/3.5 D 200.1014.442.02 AP100/3.5 S 200.1014.443.04
AP100/4.3 D 200.1015.442.02 AP100/4.3 S 200.1015.443.04
AP100/5 D 200.1016.442.02 AP100/5 S 200.1016.443.02
AP100/6.5 D 200.1017.442.02 AP100/6.5 S 200.1017.443.03
AP100/8 D 200.1018.442.02 AP100/8 S 200.1018.443.02
200 - P - 991218 - E - 00/06.02 38/104

Group AP100 Code 449P
40 0.1 ø 8.5 n. 2 passing holes
1.578"-1.579" .335" DIA
1.26"-1.258" DIA
A 8
ø 32 h8 -0.039
ø 10 67
.315"
.409"-.401"
0
2.638"
.196"-.195"
.394" DIA
10.3 0.1
-0.020
5 -0.050
.378"-.370"
9.5 0.1
.433"
11
1.578"-1.579"
Y
40 0.1
2.874"
73
X
OR 3106
X 12
23 0.1
.472"
.909"-.901" ø 8.5 D
.335" DIA Depth 12 - .47"
Suction
DIA
0
C 12 -0.4
OR 2037 22 50+5 Nm 3/8"
Pressure .472"-.457"
ø 12.7
19 20+5 Nm 1/4"
.5" DIA X
To utilize M8 DIN912
bar (PSI) 6 20+5 Nm
Pump Y +0,2
P1 P2 P3 6.5
160 180 200 0
AP100/6.5 (2300) (2600) (2900) .264"-.256"
130 150 170
AP100/8
(1900) (2100) (2400) The drawing shows a pump with counterclockwise rotation.
Dimensions Suction
Displacement
Di l t
Type A C D
cm3/rev
mm inch. mm inch. BSPP
AP100/1 2 D
AP100/1.2 12
1.2 75 5
75.5 2 97
2.97 70 2 75
2.75 1/4"
AP100/1 7 D
AP100/1.7 17
1.7 77 5
77.5 3 05
3.05 72 2 83
2.83 1/4"
AP100/2 5 D
AP100/2.5 25
2.5 81 3 19
3.19 75 5
75.5 2 97
2.97 1/4"
AP100/3 5 D
AP100/3.5 35
3.5 85 3 35
3.35 80 3 15
3.15 1/4"
AP100/4 3 D
AP100/4.3 43
4.3 89 3 50
3.50 83 5
83.5 3 29
3.29 1/4"
AP100/5 D 5 91 5
91.5 3 60
3.60 86 3 38
3.38 3/8"
AP100/6 5 D
AP100/6.5 65
6.5 96 5
96.5 3 80
3.80 91 3 58
3.58 3/8"
AP100/8 D 7.8 102 4.01 97 3.81 3/8"
AP100/1.2 D 200.1011.442.04 AP100/1.2 S 200.1011.443.02
AP100/1.7 D AP100/1.7 S 200.1012.443.02
D S
AP100/2.5 D 200.1013.442.06 AP100/2.5 S 200.1013.443.02
AP100/3.5 D 200.1014.442.04 AP100/3.5 S 200.1014.443.02
AP100/4.3 D AP100/4.3 S 200.1015.443.02
AP100/5 D AP100/5 S 200.1016.443.03
AP100/6.5 D AP100/6.5 S 200.1017.443.01
AP100/8 D AP100/8 S 200.1018.443.01
200 - P - 991218 - E - 00/06.02 39/104

Group AP100 Code 8S49P
Suction Depth 12 - .47" ø 8.5 n.2 passing holes
40 0.1
.335" DIA
1.578"-1.579"
A 8
1.26"-1.258" DIA
67
ø 32 h8 -0.039
ø 10 .315"
.409"-.401"
2.638"
.196"-.195"
0
10.3 0.1
.394" DIA
-0.020
5 -0.050
D
.378"-.370"
9.5 0.1
.433"
11
1.578"-1.579"
Y
40 0.1
2.874"
73
X
OR 3106
23 0.1 X Y
ø 8.5 B
.909"-.901" .335" DIA
0
OR 2037 C 12 -0.4 6.5 +0,2
0
Pressure .472"-.457" .264"-.256"
ø 12.7 X
.5" DIA 22 50+5 Nm 3/8" To utilize M8 DIN912

19 25+5 Nm 1/4" 6 20+5 Nm
bar (PSI)
Pump
P1 P2 P3
160 180 200
AP100/6.5 (2300) (2600) (2900)
130 150 170

AP100/8
(1900) (2100) (2400) The drawing shows a pump with counterclockwise rotation.
Dimensions Suction
Displacement
Di l t
Type A B C D
cm3/rev
mm inch. mm inch. mm inch. BSPP
AP100/1 2
AP100/1.2 12
1.2 75 5
75.5 2 97
2.97 38 5
38.5 1 51
1.51 70 2 75
2.75 1/4"
AP100/1 7
AP100/1.7 17
1.7 77 5
77.5 3 05
3.05 39 5
39.5 1 55
1.55 72 2 83
2.83 1/4"
AP100/2 5
AP100/2.5 25
2.5 81 3 19
3.19 41 1 61
1.61 75 5
75.5 2 97
2.97 1/4"
AP100/3 5
AP100/3.5 35
3.5 85 3 35
3.35 43 5
43.5 1 71
1.71 80 3 15
3.15 1/4"
AP100/4 3
AP100/4.3 43
4.3 89 3 50
3.50 45 1 77
1.77 83 5
83.5 3 29
3.29 1/4"
AP100/5 5 91 5
91.5 3 60
3.60 46 5
46.5 1 83
1.83 86 3 38
3.38 3/8"
AP100/6 5
AP100/6.5 65
6.5 96 5
96.5 3 80
3.80 49 1 93
1.93 91 3 58
3.58 3/8"
AP100/8 78
7.8 102 4 01
4.01 52 2 05
2.05 97 3 81
3.81 3/8"
AP100/1.2 D AP100/1.2 S
AP100/1.7 D AP100/1.7 S
AP100/2.5 D D AP100/2.5 S 200.1013.443.06 S
AP100/3.5 D AP100/3.5 S
AP100/4.3 D AP100/4.3 S
AP100/5 D AP100/5 S
AP100/6.5 D AP100/6.5 S 200.1017.443.04
AP100/8 D AP100/8 S
AP100/10 D AP100/10 S
200 - P - 991218 - E - 00/06.02 40/104

3.2x4x15 200.6612.0004.0
A 6.4 .126"x.59"
.250"
ø 12.7 -0.025
101.5
.500"-.499" DIA
2"-1.998" DIA
B
ø 50.8 -0.05
0
4"
0
10.5
10.3
.414"
.405"
67 19 82.5
8
2.64" .315" .745" 3.25"
Suction 3/4"-16 UNF-2B 27
.557"-.549"
14.15 -0.2
0
1.063" 0
24 55+10 Nm 3.2 -0.03
.126"-.125"
Pressure 9/16"-18 UNF-2B
19 30+10 Nm
Dimensions
Displacement
Di l t
Type A B
cm3/rev
mm inch. mm inch.
AP100/1 2
AP100/1.2 12
1.2 83 5
83.5 3 29
3.29 39 5
39.5 1 56
1.56
AP100/1 7
AP100/1.7 17
1.7 85 5
85.5 3 37
3.37 40 5
40.5 1 60
1.60
AP100/2 5
AP100/2.5 25
2.5 89 3 50
3.50 42 1 65
1.65
AP100/3 5
AP100/3.5 35
3.5 93 3 66
3.66 44 5
44.5 1 75
1.75
AP100/4 3
AP100/4.3 43
4.3 97 3 82
3.82 46 1 81
1.81
AP100/5 5 99 5
99.5 3 92
3.92 47 5
47.5 1 87
1.87
AP100/6 5
AP100/6.5 65
6.5 104 5
104.5 4 11
4.11 50 1 97
1.97
AP100/8 8 110 4.33 53 2.09
AP100/1.2 D 200.1011.802.01 AP100/1.2 S 200.1011.803.01
AP100/1.7 D 200.1012.802.01 AP100/1.7 S 200.1012.803.01
D S
AP100/2.5 D 200.1013.802.01 AP100/2.5 S 200.1013.803.01
AP100/3.5 D 200.1014.802.05 AP100/3.5 S 200.1014.803.01
AP100/4.3 D 200.1015.802.01 AP100/4.3 S 200.1015.803.03
AP100/5 D 200.1016.802.01 AP100/5 S 200.1016.803.01
AP100/6.5 D 200.1017.802.01 AP100/6.5 S 200.1017.803.01
AP100/8 D 200.1018.802.01 AP100/8 S 200.1018.803.01
200 - P - 991218 - E - 00/06.02 41/104

Group AP100 Code 887S
A 6.4
.250"
101.5
2"-1.998" DIA
B
ø 50.8 -0.05
4"
0
10.5 10.3
.414"
.405"
SAE J498-9T 20/40 DP

FLAT ROOT SIDE FIT
67 CLASS1 FIT 82.5
8 19
2.64" Suction 3/4"-16 UNF-2B .315" .745" 3.25"
27
24 55+10 Nm
1.06"
Pressure 9/16"-18 UNF-2B
19 30+10 Nm
Dimensions
Displacement
Di l t
Type A B
cm3/rev
mm inch. mm inch.
AP100/1 2
AP100/1.2 12
1.2 83 5
83.5 3 29
3.29 39 5
39.5 1 56
1.56
AP100/1 7
AP100/1.7 17
1.7 85 5
85.5 3 37
3.37 40 5
40.5 1 60
1.60
AP100/2 5
AP100/2.5 25
2.5 89 3 50
3.50 42 1 65
1.65
AP100/3 5
AP100/3.5 35
3.5 93 3 66
3.66 44 5
44.5 1 75
1.75
AP100/4 3
AP100/4.3 43
4.3 97 3 82
3.82 46 1 81
1.81
AP100/5 5 99 5
99.5 3 92
3.92 47 5
47.5 1 87
1.87
AP100/6 5
AP100/6.5 65
6.5 104 5
104.5 4 11
4.11 50 1 97
1.97
AP100/8 78
7.8 110 4 33
4.33 53 2 09
2.09
AP100/1.2 D 200.1011.862.01 AP100/1.2 S 200.1011.863.01
AP100/1.7 D 200.1012.862.01 AP100/1.7 S 200.1012.863.01
D S
AP100/2.5 D 200.1013.862.01 AP100/2.5 S 200.1013.863.01
AP100/3.5 D 200.1014.862.01 AP100/3.5 S 200.1014.863.01
AP100/4.3 D 200.1015.862.01 AP100/4.3 S 200.1015.863.01
AP100/5 D 200.1016.862.01 AP100/5 S 200.1016.863.01
AP100/6.5 D 200.1017.862.01 AP100/6.5 S 200.1017.863.02
AP100/8 D 200.1018.862.01 AP100/8 S 200.1018.863.01
200 - P - 991218 - E - 00/06.02 42/104

3.2x4x15 200.6612.0004.0
A 6.4 .126"x.59"
.250"
ø 12.7 -0.025
101.5
.500"-.499" DIA
2"-1.998" DIA
ø 50.8 -0.05
0
4"
0
10.5 30
10.3
.414" 1.181"
.405"
.433"
11
3/8" BSPP Depth 12 - .47"
82.5
50+5 Nm
67 8 19
14.15 -0.2
.557"-.549"
.315" 3.25"
Suction-Pressure
2.64" .745"
0
27 0
3.2 -0.03
1.063"
.126"-.125"
22
Dimensions
Displacement
Di l t
Type A
cm3/rev
mm inch.
AP100/1 2
AP100/1.2 12
1.2 83 5
83.5 3 29
3.29
AP100/1 7
AP100/1.7 17
1.7 85 5
85.5 3 37
3.37
AP100/2 5
AP100/2.5 25
2.5 89 3 50
3.50
AP100/3 5
AP100/3.5 35
3.5 93 3 66
3.66
AP100/4 3
AP100/4.3 43
4.3 97 3 82
3.82
AP100/5 5 99 5
99.5 3 92
3.92
AP100/6 5
AP100/6.5 65
6.5 104 5
104.5 4 11
4.11
AP100/8 78
7.8 110 4 33
4.33
AP100/1.2 D AP100/1.2 S
AP100/1.7 D AP100/1.7 S
D S
AP100/2.5 D AP100/2.5 S
AP100/3.5 D 200.1014.802.07 AP100/3.5 S
AP100/4.3 D AP100/4.3 S
AP100/5 D 200.1016.802.05 AP100/5 S
AP100/6.5 D 200.1017.802.05 AP100/6.5 S
AP100/8 D 200.1018.802.05 AP100/8 S
200 - P - 991218 - E - 00/06.02 43/104

A 6.4
.250"
101.5
2"-1.998" DIA
ø 50.8 -0.05
4"
0
10.5 30
10.3
.414" 1.181"
.405"
.433"
11
3/8" BSPP Depth 12 - .47"
SAE J498-9T 20/40 DP

FLAT ROOT SIDE FIT
50+5 Nm
67 CLASS1 FIT 82.5

8 19
Suction-Pressure
2.64" .315" .745" 3.25"

22
Dimensions
Displacement
Di l t
Type A
cm3/rev
mm inch.
AP100/1 2 D
AP100/1.2 12
1.2 83 5
83.5 3 29
3.29
AP100/1 7 D
AP100/1.7 17
1.7 85 5
85.5 3 37
3.37
AP100/2 5 D
AP100/2.5 25
2.5 89 3 50
3.50
AP100/3 5 D
AP100/3.5 35
3.5 93 3 66
3.66
AP100/4 3 D
AP100/4.3 43
4.3 97 3 82
3.82
AP100/5 D 5 99 5
99.5 3 92
3.92
AP100/6 5 D
AP100/6.5 65
6.5 104 5
104.5 4 11
4.11
AP100/8 D 8 110 4 33
4.33
AP100/1.2 D AP100/1.2 S
AP100/1.7 D AP100/1.7 S
D S
AP100/2.5 D AP100/2.5 S
AP100/3.5 D AP100/3.5 S
AP100/4.3 D AP100/4.3 S
AP100/5 D AP100/5 S
AP100/6.5 D AP100/6.5 S
AP100/8 D AP100/8 S
200 - P - 991218 - E - 00/06.02 44/104

Group AP100 Code 880 NPTF
3.2x4x15 200.6612.0004.0
A 6.4
.250" .126"x.59"
101.5
.500"-.499" DIA
B
2"-1.998" DIA
ø 12.7 -0.025
ø 50.8 -0.05
4"
0
0
10.5
10.3
.414"
.405"
67 19 82.5
8
2.64" .315" .745" 3.25"
Suction 1/2" NPTF 27
14.15 -0.2
.557"-.549"
0
1.063"
0
55+10 Nm 3.2 -0.03
.126"-.125"
Pressure 3/8" NPTF
30+10 Nm
Dimensions
Displacement
Di l t
Type A B
cm3/rev
mm inch. mm inch.
AP100/1 2
AP100/1.2 12
1.2 83 5
83.5 3 29
3.29 39 5
39.5 1 56
1.56
AP100/1 7
AP100/1.7 17
1.7 85 5
85.5 3 37
3.37 40 5
40.5 1 60
1.60
AP100/2 5
AP100/2.5 25
2.5 89 3 50
3.50 42 1 65
1.65
AP100/3 5
AP100/3.5 35
3.5 93 3 66
3.66 44 5
44.5 1 75
1.75
AP100/4 3
AP100/4.3 43
4.3 97 3 82
3.82 46 1 81
1.81
AP100/5 5 99 5
99.5 3 92
3.92 47 5
47.5 1 87
1.87
AP100/6 5
AP100/6.5 65
6.5 104 5
104.5 4 11
4.11 50 1 97
1.97
AP100/8 8 110 4 33
4.33 53 2 09
2.09
AP100/1.2 D 200.1011.802.02 AP100/1.2 S 200.1011.803.02
AP100/1.7 D 200.1012.802.02 AP100/1.7 S 200.1012.803.02
D S
AP100/2.5 D 200.1013.802.02 AP100/2.5 S 200.1013.803.02
AP100/3.5 D 200.1014.802.02 AP100/3.5 S 200.1014.803.02
AP100/4.3 D 200.1015.802.02 AP100/4.3 S 200.1015.803.01
AP100/5 D 200.1016.802.02 AP100/5 S 200.1016.803.02
AP100/6.5 D 200.1017.802.02 AP100/6.5 S 200.1017.803.02
AP100/8 D 200.1018.802.02 AP100/8 S 200.1018.803.02
200 - P - 991218 - E - 00/06.02 45/104

Group AP100 Code 887S NPTF
A 6.4
.250"
101.5 B
2"-1.998" DIA
ø 50.8 -0.05
4"
0
10.5
10.3
.414"
.405"
SAE J498-9T 20/40 DP

FLAT ROOT SIDE FIT
67 CLASS1 FIT 82.5
8 19
2.64" .315" .745" 3.25"
Suction 1/2" NPTF
27
55+10 Nm 1.06"
Pressure 3/8" NPTF
30+10 Nm
Dimensions
Displacement
Di l t
Type A B
cm3/rev
mm inch. mm inch.
AP100/1 2
AP100/1.2 12
1.2 83 5
83.5 3 29
3.29 39 5
39.5 1 56
1.56
AP100/1 7
AP100/1.7 17
1.7 85 5
85.5 3 37
3.37 40 5
40.5 1 60
1.60
AP100/2 5
AP100/2.5 25
2.5 89 3 50
3.50 42 1 65
1.65
AP100/3 5
AP100/3.5 35
3.5 93 3 66
3.66 44 5
44.5 1 75
1.75
AP100/4 3
AP100/4.3 43
4.3 97 3 82
3.82 46 1 81
1.81
AP100/5 5 99 5
99.5 3 92
3.92 47 5
47.5 1 87
1.87
AP100/6 5
AP100/6.5 65
6.5 104 5
104.5 4 11
4.11 50 1 97
1.97
AP100/8 78
7.8 110 4 33
4.33 53 2 09
2.09
AP100/1.2 D AP100/1.2 S
AP100/1.7 D AP100/1.7 S
D S
AP100/2.5 D AP100/2.5 S
AP100/3.5 D AP100/3.5 S
AP100/4.3 D AP100/4.3 S
AP100/5 D AP100/5 S
AP100/6.5 D AP100/6.5 S
AP100/8 D AP100/8 S
200 - P - 991218 - E - 00/06.02 46/104

ø13 200.6612.0002.0
.50" DIA
A
68 C B
2.677"
16
.999"-.997"
52.4
1.031"
26.2 .630"
ø 25.4f8
2.063"
M7
1.279"
3.425" 32.5
2.874"
2.830"
71.9
87
73
Taper 1:8
7.1 12 12 4
M6 Depth 13 - .50"
.28" .472" .472" .157"
11 10+2 Nm
30 30 9,6
1.181" 1.181" .378"
Suction-Pressure 20.2 9
.795" .354"
.220"-.216"
h8 (.0945"-.0939")
2.4 P9 (.0941"-.0931")
5.6 -0.1
0
Mmax.= 30 Nm
Displacement A B C Displacement A B C
cm3/rev mm inch. mm inch. mm inch. cm3/rev mm inch. mm inch. mm inch.
1.2+1.2 163 6.42 38.5 1.51 80.5 3.17 6.5+3.5 194 7.63 96 3.77
1.7+1.2 165 6.5 81.5 3.2 6.5+4.3 197.5 7.77 98 3.85
39 5
39.5 1 55
1.55 49 1 93
1.93
1.7+1.7 167 6.57 82.5 3.24 6.5+5 200 7.87 99 3.89
2.5+1.2 168.5 6.63 83.5 3.28 6.5+6.5 205 8.07 101.5 4
2.5+1.7 170.5 6.71 41 1.61 84.5 3.33 8+1.2 190 7.48 94 3.7
2.5+2.5 174 6.85 86 3.38 8+1.7 192 7.56 95 3.74
3.5+1.2 173 6.8 85.5 3.36 8+2.5 195 7.67 96.5 3.80
3.5+1.7 175 6.88 86.5 3.40 8+3.5 199.5 7.85 99 3.89
43 5
43.5 1 71
1.71 52 2 05
2.05
3.5+2.5 178 7.0 88 3.46 8+4.3 203 8.0 100.5 3.95
3.5+3.5 182.5 7.18 90 3.54 8+5 206 8.11 102 4.01
4.3+1.2 176.5 6.95 87 3.42 8+6.5 211 8.3 104.5 4.11
45 1 77
1.77
4.3+1.7 178.5 7.03 88 3.46 8+8 216.5 8.52 107 4.21
4.3+2.5 182 7.16 90 3.54 Accessories
4.3+3.5 186 7.32 45 1.77 92 3.62
Flange Splined
4.3+4.3 189.5 7.46 94 3.7 connectors couplings
5+1.2 179 7.04 88.5 3.48 RF197 GSH-1-12
5+1.7 181 7.12 89.5 3.52 RF198 GSH-1-14
5+2.5 184.5 7.26 91.5 3.61 RF199
46 5
46.5 1 83
1.83
5+3.5 189 7.45 93.5 3.68
Example of product code
5+4.3 192.5 7.57 95 3.74
D S
5+5 195 7.67 96.5 3.80
AP100/3.5+1.7 D 2218
6.5+1.2 184 7.24 91 3.58 (Clockwise rotation: D)
6.5+1.7 186 7.32 49 1.93 92 3.62 AP100/8+4.3 S 2218
6.5+2.5 189.5 7.46 94 3.7 (C.clockwise rotation: S)
200 - P - 991218 - E - 00/06.02 47/104

AP100 518
HI-LO
P
Group Code
E T
ø13 200.6612.0002.0 A
.50" DIA
C D
D -0.020
-0.053
22 50+5 Nm
65 B 68
.999"-997"DIA
2.560' 3/8" BSPP 2.677"
ø 25,4
15 16 T Depth 11 - .43" 52,4
1.031"
.59" .630" 2.063"
26,2
M7
1.279"
.433"
32,5
11
50+5 Nm
3.425"
2.830"
71,9
87
.40'
.368"DIA
2.775'
10
70,5
22
7.1
Taper 1:8
4 HI-LO
.28"
ø 9,35
.157" 57
E 9,6
P 2.24"
3/8" BSPP
Depth 12 - .47" .378" 3/8" BSPP
11 10+2 Nm 9 20,2 Depth 12 - .47"
.354" .795"
S
S
.220"-.216"
5,6 -0.1
0
h8 (.0945" -.939")
.40'
2,4
10
P9 (.0941" -.931")
1st Pump
AP100/1.2 AP100/1.7 AP100/2.5 AP100/3.5 AP100/4.3
A B C A B C A B C A B C A B C
168
AP100/1.2
6.62
170 172
AP100/1.7
6.70 6.77
173 175 178
ump
AP100/2.5
6.81 6.89 7.01
nd Pu
177 38.5 87 179 183 187

AP100/3.5
6.97 1.52 3.42 7.05 39.5 89 7.20 7.36
2n
181 183 1.56 3.50 186 41.5 92.5 191 194

AP100/4.3
7.13 7.20 7.32 1.63 3.64 7.52 43.5 97 7.64
184 186 189 194 1.71 3.82 197 45 100.5
AP100/5
7.25 7.32 7.44 7.64 7.76 1.77 3.95
189 191 194 199 202
AP100/6.5
7.45 7.52 7.64 7.83 7.95
Standard setting values for HI-LO valve: 03= 30 bar (pressures 15 55 bar) - 06= 60 bar (pressures 55 90 bar)
Composition of product code AP100/2.5–100/6.5–05–D–518 Clockwise rotation: D
03 D
AP100/**–100/**– – – 518
06 S
1st pump 2nd pump AP100/1.7–100/3.5–03–S–518 Counterclockwise rotation: S
200 - P - 991218 - E - 00/06.02 48/104

Cu.In. P1 P2 P3
AP200/4.5 4.3 .262 220 3150 250 3600 280 4000 800 1000 3500 4000
AP200/6.5 6.3 .384 220 3150 250 3600 280 4000 800 1000 3500 4000
AP200/8.5 8.3 .506 220 3150 250 3600 280 4000 800 1000 3500 4000
AP200/11 11.0 .671 210 3000 230 3300 250 3600 700 900 3500 4000
AP200/15 15.0 .915 210 3000 230 3300 250 3600 650 800 3500 4000
AP200/19 18.9 1.159 210 3000 230 3300 250 3600 650 800 3000 3500
AP200/22 21.9 1.342 200 2900 220 3150 240 3400 600 750 3000 3500
AP200/26 25.9 1.586 190 2700 210 3000 230 3300 600 750 2500 3000
45+5 Nm
M max= 65 Nm **9 M max= 65 Nm **9
6.5 8
1:5 M max= 135 Nm **5 1:8 M max= 135 Nm **8
M max= 110 Nm **7 M max= 90 Nm **7S

B17x14 DIN5482 SAE J 498-9T 16/32 DP
M max= 65 Nm **0
Notes:
200 - P - 991218 - E - 00/06.02 49/104

A
ø16 200.6612.0003.0
B 40 .63" DIA
1.58"
1.436"-1.434" DIA
Depth 13-.51"
71.5 14 28 12 89
M 12 x1,5
2.81" .55" 1.1" .47" 3.5"
ø 36.5 f8
.63"
15,9
1.28"
32,5
4.47"
3.78"
113,5
96
.33"
8,5
ø 16,65
.66" DIA
d 5 Taper 1:8 84
19 60+10 Nm
.20" 3.3"
D 12
3.2 h8
.47"
.126"-.125"
.37"
9.4
Dimensions Suction Pressure

Displacement
Di l t
Type A B d D F d D F
cm3/rev
mm inch mm inch mm inch mm inch mm mm inch mm inch mm
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 88 3 46
3.46 40 3
40.3 1 59
1.59 13 5
13.5 .53
53 30 1 18
1.18 M6X1
AP200/8 5
AP200/8.5 83
8.3 13 5
13.5 .53
53 30 1 18
1.18 M6X1
AP200/11 10 95
10.95
104 4 09
4.09 48 3
48.3 1 90
1.90
AP200/15 14 95
14.95
AP200/19 18 9
18.9 114 4 50
4.50 54 3
54.3 2 14
2.14 19 .75
75 40 1 58 M8X1.25
1.58 M8X1 25
AP200/22 21 9
21.9 19 .75
75 40 1 58 M8X1.25
1.58 M8X1 25
118 4 64
4.64 56 5
56.5 2 22
2.22
AP200/26 25 9
25.9
Accessories

AP200/4.5 D 200.1021.132.02 AP200/4.5 S 200.1021.133.02 RF223 GSH-2-14
AP200/6.5 D 200.1022.132.02 AP200/6.5 S 200.1022.133.05 RF224 GSH-2-15
D S
AP200/8.5 D 200.1023.132.02 AP200/8.5 S 200.1023.133.02 RF225 GSH-2-18
AP200/11 D 200.1024.132.02 AP200/11 S 200.1024.133.02 RF238
AP200/15 D 200.1025.132.02 AP200/15 S 200.1025.133.02 RF246
AP200/19 D 200.1026.132.02 AP200/19 S 200.1026.133.02 RF251
AP200/22 D 200.1027.132.02 AP200/22 S 200.1027.133.02
AP200/26 D 200.1028.132.02 AP200/26 S 200.1028.133.02
200 - P - 991218 - E - 00/06.02 50/104

A
ø16 200.6612.0003.0
B 40 .63" DIA
1.58"
1.436"-1.434" DIA
71.5 14 28 12 89
M 12 x1,5
2.81" 1.1" .47" 3.5"
ø 36.5 f8
.55"
.63"
1.28"
15.9
32,5
4.47"
3.78"
113,5
96
.33"
8,5
ø 16,65
.66" DIA
5 Taper 1:8 19 84
G 60+10 Nm
.20" 3.3"
Suction-Pressure
12
22 50+5 Nm 3/8" .47" 3.2 h8
.126"-.125"
9.4
.37"
27 60+10 Nm 1/2"
32 100+10 Nm 3/4"

Displacement A B G G
Type
cm3/rev
mm inch. mm inch. BSPP BSPP
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 88 3 46
3.46 40 3
40.3 1 59
1.59 3/8"
AP200/8 5
AP200/8.5 83
8.3 3/8"
AP200/11 10 95
10.95
104 4 09
4.09 48 3
48.3 1 90
1.90 1/2"
AP200/15 14 95
14.95
AP200/19 18 9
18.9 114 4 50
4.50 54 3
54.3 2 14
2.14
AP200/22 21 9
21.9 3/4" 1/2"
118 4 64
4.64 56 5
56.5 2 22
2.22
AP200/26 25 9
25.9
Accessories

AP200/4.5 D 200.1021.132.04 AP200/4.5 S 200.1021.133.03 GSH-2-14
AP200/6.5 D 200.1022.132.03 AP200/6.5 S 200.1022.133.04 GSH-2-15
D S
AP200/8.5 D 200.1023.132.04 AP200/8.5 S 200.1023.133.03 GSH-2-18
AP200/11 D 200.1024.132.04 AP200/11 S 200.1024.133.05
AP200/15 D 200.1025.132.07 AP200/15 S 200.1025.133.05
AP200/19 D 200.1026.132.05 AP200/19 S 200.1026.133.04
AP200/22 D 200.1027.132.05 AP200/22 S 200.1027.133.03
AP200/26 D 200.1028.132.03 AP200/26 S 200.1028.133.04
200 - P - 991218 - E - 00/06.02 51/104

Group AP200 Code 219A
A 28
1.1"
B
Depth 13-.51"
71.5 14 89
.71"-.70"DIA
-0.006
ø 18 -0.017
1.436"-1.434" DIA
2.81" .55" 3.5"
ø 36.5 f8
6.5 0.05
.36"-.25"
15,9
1.28"
.63"
32,5
4.47"
3.78"
113,5
96
.33"
8,5
d 5 84
.20" 3.3"
bar (PSI) D 8 0.1
Pump
P1 P2 P3 .32"-.31"
180 210 230
AP200/15 (2600) (3000) (3300)
140 165 185

AP200/19
(2000) (2400) (2650)
120 145 165
AP200/22 (1700) (2050) (2350)
100 120 140
AP200/26 (1450) (1750) (2000)

Displacement A B d D F d D F
Type
cm3/rev
AP200/4.5 4.3
AP200/6.5 6.3 88 3.46 40.3 1.59 13.5 .53 30 1.18 M6X1

AP200/8.5 8.3 13.5 .53 30 1.18 M6X1
AP200/11 10.95
104 4 09
4.09 48 3
48.3 1 90
1.90
AP200/15 14.95
AP200/19 18.9 114 4.50 54.3 2.14 19 .75 40 1.58 M8X1.25

AP200/22 21.9 19 .75 40 1.58 M8X1.25
118 4 64
4.64 56 5
56.5 2 22
2.22
AP200/26 25.9
Accessories

AP200/4.5 D AP200/4.5 S RF223
AP200/6.5 D AP200/6.5 S RF224
D S
AP200/8.5 D AP200/8.5 S RF225
AP200/11 D AP200/11 S RF238
AP200/15 D AP200/15 S RF246
AP200/19 D 200.1026.142.02 AP200/19 S RF251
AP200/22 D AP200/22 S
AP200/26 D AP200/26 S
200 - P - 991218 - E - 00/06.02 52/104

A
B 3
.12"
-0.010
ø 67 -0.030
63.5 0.1 9.5
ø 42 H6
ø 17.6
2.503"-2.496" .374"
2.637"-2.636" DIA
3.150"-3.130"
1.574"
2.503"-2.496"
+0.5
40
15,9
.693" DIA
1.653" DIA
.63"
63.5 0.1
4.173"
79.5
106
F
Depth 16-.623"
Depth 13-.51"
M8
-0.060
8 -0.075 d 10 5.5 84
.313"-.312" .393" .216" 3.31"
D
Max pressure (M max= 65 Nm) OR 68.0X3.0 - 70Sh
bar (PSI)
Pump
P1 P2 P3
180 210 230
AP200/15
(2600) (3000) (3300)
140 165 185
AP200/19
(2000) (2400) (2650)
120 145 165
AP200/22 (1700) (2050) (2350)
100 120 140
AP200/26 (1450) (1750) (2000)

Type
cm3/rev
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 98 3 86
3.86 55 2 17
2.17 13 5
13.5 .53
53 30 1 18
1.18 M6X1
AP200/8 5
AP200/8.5 83
8.3 13 5
13.5 .53
53 30 1 18
1.18 M6X1
AP200/11 10 95
10.95
114 45
4.5 63 2 48
2.48
AP200/15 14 95
14.95
AP200/19 18 9
18.9 126 4 96
4.96 69 2 17
2.17 19 .75
75 40 1 58
1.58 M8X1 25
M8X1.25
AP200/22 21 9
21.9 19 .75
75 40 1 58
1.58 M8X1 25
M8X1.25
131 5 15
5.15 71 2 79
2.79
AP200/26 25 9
25.9
Accessories

AP200/4.5 D 200.1021.942.01 AP200/4.5 S RF223
AP200/6.5 D 200.1022.942.01 AP200/6.5 S RF224
D S
AP200/8.5 D 200.1023.942.01 AP200/8.5 S 200.1023.943.02 RF225
AP200/11 D 200.1024.942.01 AP200/11 S RF238
AP200/15 D 200.1025.942.03 AP200/15 S RF246
AP200/19 D 200.1026.942.01 AP200/19 S RF251
AP200/22 D 200.1027.942.01 AP200/22 S
AP200/26 D 200.1028.942.01 AP200/26 S
200 - P - 991218 - E - 00/06.02 53/104

Group AP200 Code 201K8
A
B ø16 200.6612.0003.0
.63"DIA
Depth 13-.51"
71.5 45 28 12 89
1.436"-1.434" DIA
M 12 x1,5
2.81" 1.77" 1.1" .47" 3.5"
ø 36.5f8
15,9
1.28"
.63"
32,5
4.47"
3.78"
113,5
96
.33"
8,5
ø 16,65
.66" DIA
d 5 Taper 1:8 19 84
60+10 Nm
.20" 3.3"
D 12
Max pressure (M max= 65 Nm) .47" a 3.2 h8
.37"
9.4
bar (PSI) .126"-.125"
Pump Fr (N) Lh = 1000 h
P1 P2 P3
180 210 230 1750 Fr
AP200/15 (2600) (3000) (3300) 1600
1450 Fa
140 165 185
AP200/19 1300
(2000) (2400) (2650)
1150
120 145 165 1000
AP200/22 (1700) (2050) (2350) 850
100 120 140 700 With Fr and Fa the max radial load is:
AP200/26 (1450) (1750) (2000) Fr max.= Fr - (0.7 Fa)
20 30 40 50 60 a (mm)

Displacement
Di l t
cm3/rev
AP200/4.5 4.3
AP200/6.5 6.3 113 4.4 66.3 2.61 13.5 .53 30 1.18 M6X1
AP200/8.5 8.3 13.5 .53 30 1.18 M6X1
AP200/11 10.95
129 5 74 3
74.3 2 92
2.92
AP200/15 14.95
AP200/19 18.9 143 5.6 80.3 3.16 19 .75 40 1.58 M8X1.25
AP200/22 21.9 19 .75 40 1.58 M8X1.25
148 58
5.8 82 5
82.5 3 25
3.25
AP200/26 25.9
Accessories

AP200/4.5 D 200.1021.132.06 AP200/4.5 S 200.1021.133.01 RF223 GSH-2-14
AP200/6.5 D 200.1022.132.01 AP200/6.5 S 200.1022.133.01 RF224 GSH-2-15
D S
AP200/8.5 D 200.1023.132.01 AP200/8.5 S 200.1023.133.01 RF225 GSH-2-18
AP200/11 D 200.1024.132.01 AP200/11 S 200.1024.133.01 RF238
AP200/15 D 200.1025.132.01 AP200/15 S 200.1025.133.01 RF246
AP200/19 D 200.1026.132.01 AP200/19 S 200.1026.133.01 RF251
AP200/22 D 200.1027.132.01 AP200/22 S 200.1027.133.01
AP200/26 D 200.1028.132.01 AP200/26 S 200.1028.133.01
200 - P - 991218 - E - 00/06.02 54/104

Group AP200 Code 201K0
A
B 30
.787"-.786" DIA
1.18"
Depth 13-.51"
1.436"-1.434" DIA
ø 20 h8
ø 36.5f8
71.5 45 6.5 89
2.81" 1.77" .256" 3.5"
15,9
.63"
1.28"
32,5
4.47"
113,5
3.78"
96
.33"
8,5
6x25 DIN6885
.23"x.98"
d 5 84
.20" 3.3"
.889"-.882"
Max pressure (M max= 65 Nm) a
0.1
bar (PSI) 6 h8
Pump
22.5
P1 P2 P3 Fr (N) Lh = 1000 h
Fr .236"-.235"
180 210 230 1750
AP200/15 Fa
(2600) (3000) (3300) 1600
140 165 185 1450
AP200/19 1300
(2000) (2400) (2650)
1150 M6
120 145 165 1000
AP200/22 (1700) (2050) (2350) 850 With Fr and Fa the max radial load is:
100 120 140 700
AP200/26 Fr max.= Fr - (0.7 Fa)
(1450) (1750) (2000)
20 30 40 50 60 a (mm)

Displacement
Di l t
cm3/rev
AP200/4.5 4.3
AP200/6.5 6.3 113 4.4 66.3 2.61 13.5 .53 30 1.18 M6X1
AP200/8.5 8.3 13.5 .53 30 1.18 M6X1
AP200/11 10.95
129 5 74 3
74.3 2 92
2.92
AP200/15 14.95
AP200/19 18.9 143 5.6 80.3 3.16 19 .75 40 1.58 M8X1.25
AP200/22 21.9 19 .75 40 1.58 M8X1.25
148 58
5.8 82 5
82.5 3 25
3.25
AP200/26 25.9
Accessories

AP200/4.5 D 200.1021.102.01 AP200/4.5 S 200.1021.103.01 RF223
AP200/6.5 D 200.1022.102.01 AP200/6.5 S 200.1022.103.01 RF224
D S
AP200/8.5 D 200.1023.102.01 AP200/8.5 S 200.1023.103.01 RF225
AP200/11 D 200.1024.102.01 AP200/11 S 200.1024.103.01 RF238
AP200/15 D 200.1025.102.01 AP200/15 S 200.1025.103.01 RF246
AP200/19 D 200.1026.102.01 AP200/19 S 200.1026.103.01 RF251
AP200/22 D 200.1027.102.01 AP200/22 S 200.1027.103.01
AP200/26 D 200.1028.102.01 AP200/26 S 200.1028.103.01
200 - P - 991218 - E - 00/06.02 55/104

A 37.7
1.48" ø16 DIN6888
B 24.7 .63" DIA
.97"
72 15 13 90
2.83" .6" .51" 3.54"
M 12 x1,5
3.147"-3.145. DIA
1.36"
15.9
.63"
34.5
ø 80 e8
3.94"
4.65"
118
100
.354"
9
ø 17
Depth 13-.51"
.67"DIA
Taper 1:5
19 60+10 Nm
d 7.2 84
.28" 3.31"
D 7.7
.30" 3 h8
.118"-.117"
.37"
9.5

Type
cm3/rev
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 85 3 35
3.35 41 3
41.3 1 63
1.63 15 .59
59
AP200/8 5
AP200/8.5 83
8.3
AP200/11 10 95
10.95 40 1 58
1.58 M6X1 15 .59
59 35 1 38
1.38 M6X1
101 4 49 3
49.3 1 94
1.94
AP200/15 14 95
14.95
20 .79
79
AP200/19 18 9
18.9 113 4 44
4.44 55 3
55.3 2 18
2.18
AP200/22 21 9
21.9 117 4 60
4.60 57 5
57.5 2 26
2.26
Accessories

AP200/4.5 D 200.1021.222.03 AP200/4.5 S 200.1021.223.03 RF221 GSH-2B-14
AP200/6.5 D 200.1022.222.03 D AP200/6.5 S 200.1022.223.03 S RF262 GSH-2B-15
AP200/8.5 D 200.1023.222.03 AP200/8.5 S 200.1023.223.03 RF216 GSH-2B-18
AP200/11 D 200.1024.222.02 AP200/11 S 200.1024.223.02 RF252
AP200/15 D 200.1025.222.03 AP200/15 S 200.1025.223.01 RF217
AP200/19 D 200.1026.222.03 AP200/19 S 200.1026.223.03 RF220
AP200/22 D 200.1027.222.03 AP200/22 S 200.1027.223.01
200 - P - 991218 - E - 00/06.02 56/104

A 23.5
.92"
.645"-.65"DIA
B 14
ø 16.5 h11
.55"
72 15 90
2.83" .6" 3.54"
3.147"-3.145" DIA
1.36"
15.9
.63"
34.5
ø 80 e8
3.94"
4.65"
118
100
.354"
9
F
Depth 13-.51"
B 17x14
DIN 5482
d 7.2 84
.28" 3.31"
D

Type
cm3/rev
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 85 3 35
3.35 41 3
41.3 1 63
1.63 15 .59
59
AP200/8 5
AP200/8.5 83
8.3
AP200/11 10 95
10.95
101 4 49 3
49.3 1 94
1.94 40 1 58
1.58 M6X1 15 .59
59 35 1 38
1.38 M6X1
AP200/15 14 95
14.95
AP200/19 18 9
18.9 113 4 44
4.44 55 3
55.3 2 18
2.18 20 .79
79
AP200/22 21 9
21.9
117 4 60
4.60 57 5
57.5 2 26
2.26
AP200/26 25 9
25.9
Accessories

AP200/4.5 D 200.1021.252.01 AP200/4.5 S 200.1021.253.01 RF221
AP200/6.5 D 200.1022.252.01 AP200/6.5 S 200.1022.253.01 RF262
D S
AP200/8.5 D 200.1023.252.01 AP200/8.5 S 200.1023.253.01 RF216
AP200/11 D 200.1024.252.01 AP200/11 S 200.1024.253.01 RF252
AP200/15 D 200.1025.252.01 AP200/15 S 200.1025.253.01 RF217
AP200/19 D 200.1026.252.01 AP200/19 S 200.1026.253.01 RF220
AP200/22 D 200.1027.252.01 AP200/22 S 200.1027.253.01
AP200/26 D 200.1028.252.01 AP200/26 S 200.1028.253.01
200 - P - 991218 - E - 00/06.02 57/104

A 40,5 ø16 DIN6888
Depth 13-.51"
1.59"
.63" DIA
60 B 27,5
1.967"-1.966" DIA
2.36" 1.08"
ø 50 f8
M 12 x1,5
X
7.2 13
.28" .47"
.563"
14.3
15,9
.63"
F
2.38"
60.4
3.94"
100
ø 17
.67" DIA 84
10.5 d 3.31"
.413" Taper 1:5 X
19 60+10 Nm
8 D 10,5
.315" .413"
3 h8
.118"-.117"
.37"
9.5
17 45+5 Nm

Type
cm3/rev
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 74 29
2.9 40 1 57
1.57 15 .59
59
AP200/8 5
AP200/8.5 83
8.3
AP200/11 10 95
10.95 40 1 58
1.58 M6X1 15 .59
59 35 1 38
1.38 M6X1
90 3 55
3.55 46 5
46.5 1 83
1.83
AP200/15 14 95
14.95
20 .79
79
AP200/19 18 9
18.9 102 4 52 3
52.3 2 06
2.06
AP200/22 21 9
21.9 106 4 17
4.17 54 5
54.5 2 15
2.15
Accessories

AP200/4.5 D 200.1021.322.01 AP200/4.5 S 200.1021.323.01 RF221 GSH-2B-14
AP200/6.5 D 200.1022.322.01 D AP200/6.5 S 200.1022.323.01 S RF262 GSH-2B-15
AP200/8.5 D 200.1023.322.01 AP200/8.5 S 200.1023.323.01 RF216 GSH-2B-18
AP200/11 D 200.1024.322.01 AP200/11 S 200.1024.323.02 RF252
AP200/15 D 200.1025.322.02 AP200/15 S 200.1025.353.01 RF217
AP200/19 D 200.1026.322.01 AP200/19 S 200.1026.323.01 RF220
AP200/22 D 200.1027.322.01 AP200/22 S 200.1027.323.01
200 - P - 991218 - E - 00/06.02 58/104

A 40,5 ø16 DIN6888

1.59"
F Depth 13-.51"
.63" DIA
60 B 27,5
2.36" 1.08"
1.967"-1.966" DIA
ø 50 f8
M 12 x1,5
X
7.2 13
.28" .47"
.563"
14.3
15,9
.63"
2.38"
60.4
3.94"
100
ø 17
.67"DIA 84
10.5 d 3.31"
Taper 1:5
.413" X
19 60+10 Nm
8 D 10,5
.315" .413"
3 h8
.118"-.117"
.37"
9.5
17 45+5 Nm

Type
cm3/rev
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 74 29
2.9 40 1 57
1.57 15 .59
59
AP200/8 5
AP200/8.5 83
8.3
AP200/11 10 95
10.95 40 1 58
1.58 M6X1 15 .59
59 35 1 38
1.38 M6X1
90 3 55
3.55 46 5
46.5 1 83
1.83
AP200/15 14 95
14.95
20 .79
79
AP200/19 18 9
18.9 102 4 52 3
52.3 2 06
2.06
AP200/22 21 9
21.9 106 4 17
4.17 54 5
54.5 2 15
2.15
Accessories

AP200/4.5 D 200.1021.422.02 AP200/4.5 S 200.1021.423.02 RF221 GSH-2B-14
AP200/6.5 D 200.1022.422.02 D AP200/6.5 S 200.1022.423.02 S RF262 GSH-2B-15
AP200/8.5 D 200.1023.422.02 AP200/8.5 S 200.1023.423.02 RF216 GSH-2B-18
AP200/11 D 200.1024.422.01 AP200/11 S 200.1024.423.01 RF252
AP200/15 D 200.1025.422.03 AP200/15 S 200.1025.423.01 RF217
AP200/19 D 200.1026.422.02 AP200/19 S 200.1026.423.02 RF220
AP200/22 D 200.1027.422.02 AP200/22 S 200.1027.423.01
200 - P - 991218 - E - 00/06.02 59/104

.645"-.65" DIA
A 26.3
ø 16.5 h11
1.03"
Depth 13-.51"
60 B
1.967"-1.966"DIA
2.36"
ø 50 f8
14 X
.55"
.563"
14.3
15,9
.63"
F
2.38"
3.94"
60.4
100
B 17x14
DIN 5482
10.5 d 84
.413" X 3.31"
7.2
8 D .28"
.315"
17 45+5 Nm

Displacement
Di l t
cm3/rev
AP200/4.5 4.3
AP200/6.5 6.3 74 2.9 40 1.57 15 .59
AP200/8.5 8.3
AP200/11 10.95 40 1.58 M6X1 15 .59 35 1.38 M6X1
90 3 55
3.55 46 5
46.5 1 83
1.83
AP200/15 14.95
20 .79
79
AP200/19 18.9 102 4 52.3 2.06
AP200/22 21.9 106 4.17 54.5 2.15
Accessories

AP200/4.5 D AP200/4.5 S RF221 GSH-2B-14
AP200/6.5 D D AP200/6.5 S S RF262 GSH-2B-15
AP200/8.5 D 200.1023.352.01 AP200/8.5 S RF216 GSH-2B-18
AP200/11 D 200.1024.352.02 AP200/11 S RF252
AP200/15 D AP200/15 S RF217
AP200/19 D AP200/19 S RF220
AP200/22 D 200.1027.352.01 AP200/22 S
200 - P - 991218 - E - 00/06.02 60/104

.645"-.65"DIA
A 26.3
ø 16.5 h11
1.03"
Depth 13-.51"
1.967"-1.966" DIA
60 B
2.36"
ø 50 f8
14 X
.55"
.563"
14.3
15,9
.63"
F
2.38"
3.94"
60.4
100
B 17x14
DIN 5482
10.5 d X 84
.413" 7.2 3.31"
8 D .28"
.315"
17 45+5 Nm

Displacement
Di l t
cm3/rev
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 74 29
2.9 40 1 57
1.57 15 .59
59
AP200/8 5
AP200/8.5 83
8.3
AP200/11 10 95
10.95 40 1 58
1.58 M6X1 15 .59
59 35 1 38
1.38 M6X1
90 3 55
3.55 46 5
46.5 1 83
1.83
AP200/15 14 95
14.95
20 .79
79
AP200/19 18 9
18.9 102 4 52 3
52.3 2 06
2.06
AP200/22 21 9
21.9 106 4 17
4.17 54 5
54.5 2 15
2.15
Accessories

AP200/4.5 D AP200/4.5 S RF221 GSH-2B-14
AP200/6.5 D D AP200/6.5 S S RF262 GSH-2B-15
AP200/8.5 D 200.1023.452.01 AP200/8.5 S RF216 GSH-2B-18
AP200/11 D 200.1024.452.01 AP200/11 S 200.1024.453.01 RF252
AP200/15 D AP200/15 S RF217
AP200/19 D 200.1026.452.01 AP200/19 S 200.1026.453.01 RF220
AP200/22 D 200.1027.452.01 AP200/22 S
200 - P - 991218 - E - 00/06.02 61/104

A
60 B 7.2
.28"
2.36" -0.060
8 -0.075 3.2
.126" X
.313"-.312" 2
X
2.046"-2.045" DIA
.079"
.563"
14.3
.63"
15.9
1.882"DIA
1.5" DIA
ø 52 f7
ø 47.8
ø 38
11
3.94"
2.38"
60.4
100
.7" DIA
.35"
ø 17.6
9
F
Depth 13-.51"
d 2.7
10.5 .106" 84 To utilize
.413" 1.5 3.3"
M10x1.5 DIN931
.06" OR3187 - 70Sh
D 6.5 17
45+5 Nm
.256"

bar (PSI) Pump side Joint Coupling side
Pump 8
P1 P2 P3
.314"-.312"
+0.1
X X-X .315" 6.5 0
-0.025
8 -0.063
180 210 230
AP200/15 (2600) (3000) (3300) +0.046
2.050"-2.047"
.260"-.256"
1.181" DIA
ø 18 max
.708"
140 165 185
ø 52 0
ø 30
AP200/19 M
(2000) (2400) (2650)
120 145 165
AP200/22 (1700) (2050) (2350) X
0
100 120 140 11 2.5 -0.5
AP200/26 (1450) (1750) (2000) .433" .098"-.079"

Type
cm3/rev
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 74 29
2.9 38 5
38.5 1 51
1.51 15 .59
59
AP200/8 5
AP200/8.5 83
8.3
AP200/11 10 95
10.95 40 1 58
1.58 M6X1 15 .59
59 35 1 38
1.38 M6X1
90 3 54
3.54 46 5
46.5 1 83
1.83
AP200/15 14 95
14.95
20 .79
79
AP200/19 18 9
18.9 102 4 52 5
52.5 2 06
2.06
AP200/22 21 9
21.9 106 42
4.2 54 8
54.8 2 16
2.16
Accessories

AP200/4.5 D 200.1021.542.01 AP200/4.5 S 200.1021.543.02 RF221
AP200/6.5 D 200.1022.542.01 D AP200/6.5 S 200.1022.543.01 S RF262
AP200/8.5 D 200.1023.542.01 AP200/8.5 S 200.1023.543.01 RF216
AP200/11 D 200.1024.542.01 AP200/11 S 200.1024.543.01 RF252
AP200/15 D 200.1025.542.02 AP200/15 S 200.1025.543.01 RF217
AP200/19 D 200.1026.542.01 AP200/19 S 200.1026.543.01 RF220
AP200/22 D 200.1027.542.01 AP200/22 S 200.1027.543.01
200 - P - 991218 - E - 00/06.02 62/104

Group AP200 Code 225KM5
A 45
1.77"
B 29.5 ø16 DIN6888
1.16" .63" DIA
72 13 15.5 90
2.83" .51" .61" 3.54"
M 14 x1,5
3.147"-3.145 DIA
1.36"
.63"
15.9
34.5
ø 80 e8
3.94"
4.65"
118
100
.354"
9
F
Depth 13-.51"
ø 20
.79"DIA
Taper 1:5
d 8 22
80+20 Nm
84
.31"
a 3.31"
Max pressure (M max= 65 Nm) D
bar (PSI) 4 h8
Pump Fr (N) Lh = 1000 h
P1 P2 P3
Fr .157"-.156"
180 210 230 1750
.43"
11
AP200/15 1600
(2600) (3000) (3300)
1450 Fa
140 165 185
AP200/19 1300
(2000) (2400) (2650)
1150
120 145 165 1000
AP200/22 (1700) (2050) (2350) 850
100 120 140 700 With Fr and Fa the max radial load is:
AP200/26
(1450) (1750) (2000) Fr max.= Fr - (0.7 Fa)
20 30 40 50 60 a (mm)

Type
cm3/rev
AP200/4.5 4.3
AP200/6.5 6.3 116 4.56 72.5 2.85 15 .59

AP200/8.5 8.3
AP200/11 10.95
132 5 20
5.20 80 5
80.5 3 17
3.17 40 1 58
1.58 M6X1 15 .59
59 35 1 38
1.38 M6X1
AP200/15 14.95
AP200/19 18.9 144 5.67 86.5 3.4 20 .79

AP200/22 21.9
148 5 82
5.82 88 8
88.8 35
3.5
AP200/26 25.9
Accessories

AP200/4.5 D AP200/4.5 S RF221
AP200/6.5 D AP200/6.5 S RF262
D S
AP200/8.5 D 200.1023.222.09 AP200/8.5 S RF216
AP200/11 D 200.1024.222.03 AP200/11 S 200.1024.223.04 RF252
AP200/15 D 200.1025.222.04 AP200/15 S 200.1025.223.02 RF217
AP200/19 D AP200/19 S 200.1026.223.02 RF220
AP200/22 D 200.1027.222.04 AP200/22 S
AP200/26 D AP200/26 S
200 - P - 991218 - E - 00/06.02 63/104

A 31,7
1.25"
.6085"-.6035"
15.456-0.127
106,4 B 14
4.2" .55"
0
12 11
.47" .43"
3.25"-3.248" DIA
ø 82.55 -0.05
15,9
.63"
0
4.47"
113.5
130,5 G 6.4 84
SAE J 498-9T 3.31"
5.14" Suction-Pressure .25"
16/32 DP
FLAT ROOT SIDE FIT
CLASS 1 FIT
100+10 Nm 1-1/16 12UNF
65+10 Nm 7/8 14UNF

Type
cm3/rev
mm inch mm inch 12UNF 14UNF
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 82 5
82.5 3 23
3.23 39 5
39.5 1 55
1.55
AP200/8 5
AP200/8.5 83
8.3
AP200/11 10 95
10.95
98 5
98.5 39
3.9 47 5
47.5 1 87
1.87 1-1/16 7/8
AP200/15 14 95
14.95
AP200/19 18 9
18.9 110 5
110.5 4 35
4.35 53 5
53.5 2 11
2.11
AP200/22 21 9
21.9
115 4 53
4.53 55 5
55.5 2 18
2.18
AP200/26 25 9
25.9
AP200/4.5 D 200.1021.862.02 AP200/4.5 S 200.1021.863.02
AP200/6.5 D 200.1022.862.02 AP200/6.5 S 200.1022.863.02
D S
AP200/8.5 D 200.1023.862.02 AP200/8.5 S 200.1023.863.02
AP200/11 D 200.1024.862.01 AP200/11 S 200.1024.863.03
AP200/15 D 200.1025.862.04 AP200/15 S 200.1025.863.04
AP200/19 D 200.1026.862.02 AP200/19 S 200.1026.863.02
AP200/22 D 200.1027.862.02 AP200/22 S 200.1027.863.02
AP200/26 D 200.1028.862.02 AP200/26 S 200.1028.863.02
200 - P - 991218 - E - 00/06.02 64/104

A 31.7
1.25"
106,4 B 4x18 DIN6885
4.2" .157"x.708"
12 11
.47" .43"
3.25"-3.248" DIA
ø 82.55 -0.05
15,9
.63"
0
4.47"
113.5
0
130,5 G 6.4 15.875 -0.025 84
5.14" .25" 3.31"
Suction-Pressure .625"-.624"
17.7 -0.2
+0.03
.7"-.69" 3.97
0
0
100+10 Nm 1-1/16 12UNF .158"-.156"
65+10 Nm 7/8 14UNF

1/4"-28 UNF

Type
cm3/rev
mm inch mm inch 12UNF 14UNF
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 82 5
82.5 3 23
3.23 39 5
39.5 1 55
1.55
AP200/8 5
AP200/8.5 83
8.3
AP200/11 10 95
10.95
98 5
98.5 39
3.9 47 5
47.5 1 87
1.87 1-1/16 7/8
AP200/15 14 95
14.95
AP200/19 18 9
18.9 110 5
110.5 4 35
4.35 53 5
53.5 2 11
2.11
AP200/22 21 9
21.9
115 4 53
4.53 55 5
55.5 2 18
2.18
AP200/26 25 9
25.9
AP200/4.5 D 200.1021.802.02 AP200/4.5 S 200.1021.803.03
AP200/6.5 D 200.1022.802.02 AP200/6.5 S 200.1022.803.05
D S
AP200/8.5 D 200.1023.802.02 AP200/8.5 S 200.1023.803.02
AP200/11 D 200.1024.802.02 AP200/11 S 200.1024.803.02
AP200/15 D 200.1025.802.02 AP200/15 S 200.1025.803.02
AP200/19 D 200.1026.802.02 AP200/19 S 200.1026.803.02
AP200/22 D 200.1027.802.02 AP200/22 S 200.1027.803.02
AP200/26 D 200.1028.802.02 AP200/26 S 200.1028.803.02
200 - P - 991218 - E - 00/06.02 65/104

Group AP200 Code 887S NPTF
A 31,7
1.25"
15.456 -0.127
.6085"-.6035"
106,4 B 14
0
4.2" .55"
12 11
.47" .43"
3.25"-3.248" DIA
-0.05
15,9
.63"
0
4.47"
113.5
ø 82.55
130,5 G 6.4 SAE J 498-9T 84
5.14" Suction-Pressure .25" 16/32 DP 3.31"
FLAT ROOT SIDE FIT
CLASS 1 FIT
100+10 Nm 3/4" NPTF
55+10 Nm 1/2" NPTF

Displacement
Di l t
Type A B G G
cm3/rev
mm inch mm inch NPTF NPTF
AP200/11 10 95
10.95
98 5
98.5 39
3.9 47 5
47.5 1 87
1.87
AP200/15 14 95
14.95
AP200/19 18 9
18.9 110 5
110.5 4 35
4.35 53 5
53.5 2 11
2.11 3/4" 1/2"
AP200/22 21 9
21.9
115 4 53
4.53 55 5
55.5 2 18
2.18
AP200/26 25 9
25.9
D S
AP200/11 D AP200/11 S
AP200/15 D AP200/15 S
AP200/19 D AP200/19 S
AP200/22 D AP200/22 S
AP200/26 D AP200/26 S
200 - P - 991218 - E - 00/06.02 66/104

Group AP200 Code 880 NPTF
A 31.7
1.25"
106,4 B 4x18 DIN6885
4.2" .157"x.708"
12 11
.47" .43"
3.25"-3.248" DIA
ø 82.55 -0.05
15,9
.63"
0
4.47"
113.5
0
130,5 6.4 15.875 -0.025 84
G
5.14" .25" .625"-.624" 3.31"
Suction-Pressure 17.7 -0.2
+0.03
.7"-.69" 3.97
0
100+10 Nm 3/4" NPTF .158"-.156"
55+10 Nm 1/2" NPTF

1/4"-28 UNF

Displacement
Di l t
Type A B G G
cm3/rev
mm inch mm inch NPTF NPTF
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 82 5
82.5 3 23
3.23 39 5
39.5 1 55
1.55 1/2" 1/2"
AP200/8 5
AP200/8.5 83
8.3
AP200/11 10 95
10.95
98 5
98.5 39
3.9 47 5
47.5 1 87
1.87
AP200/15 14 95
14.95
AP200/19 18 9
18.9 110 5
110.5 4 35
4.35 53 5
53.5 2 11
2.11 3/4" 1/2"
AP200/22 21 9
21.9
115 4 53
4.53 55 5
55.5 2 18
2.18
AP200/26 25 9
25.9
AP200/4.5 D 200.1021.802.07 AP200/4.5 S 200.1021.803.05
AP200/6.5 D 200.1022.802.06 AP200/6.5 S 200.1022.803.08
D S
AP200/8.5 D 200.1023.802.07 AP200/8.5 S 200.1023.803.04
AP200/11 D 200.1024.802.03 AP200/11 S
AP200/15 D 200.1025.802.03 AP200/15 S
AP200/19 D 200.1026.802.03 AP200/19 S
AP200/22 D 200.1027.802.03 AP200/22 S
AP200/26 D 200.1028.802.03 AP200/26 S
200 - P - 991218 - E - 00/06.02 67/104

Group AP200 Code 287S–B
A 31,7
1.25"
106,4
.6085"-.6035"
15.456 -0.127
B 14
Depth 13-.51"
4.2" .55"
0
12 11
.47" .43"
.63"
15,9
3.25"-3.248" DIA
ø 82.55 -0.05
F
0
4.47"
113.5
130,5 d 6.4 84
SAE J 498-9T
5.14" .25" 3.31"
16/32 DP
D FLAT ROOT SIDE FIT
CLASS 1 FIT

Type
cm3/rev
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 82 5
82.5 3 23 39.5
3.23 39 5 1.55
1 55 15 .59
59
AP200/8 5
AP200/8.5 83
8.3
AP200/11 10 95
10.95
98 5
98.5 39
3.9 47 5 1.87
47.5 1 87 40 1 58
1.58 M6X1 13 5
13.5 .53
53 35 1 38
1.38 M6X1
AP200/15 14 95
14.95
AP200/19 18 9
18.9 110 5
110.5 4 35 53.5
4.35 53 5 2.11
2 11 20 .79
79
AP200/22 21 9
21.9
115 4 53 55.5
4.53 55 5 2.18
2 18
AP200/26 25 9
25.9
Accessories

AP200/4.5 D 200.1021.862.01 AP200/4.5 S 200.1021.863.01 RF221
AP200/6.5 D 200.1022.862.01 AP200/6.5 S 200.1022.863.01 RF262
D S
AP200/8.5 D 200.1023.862.01 AP200/8.5 S 200.1023.863.01 RF216
AP200/11 D 200.1024.862.04 AP200/11 S 200.1024.863.04 RF252
AP200/15 D 200.1025.862.02 AP200/15 S 200.1025.863.03 RF217
AP200/19 D 200.1026.862.01 AP200/19 S 200.1026.863.01 RF220
AP200/22 D 200.1027.862.01 AP200/22 S 200.1027.863.01
AP200/26 D 200.1028.862.01 AP200/26 S 200.1028.863.01
200 - P - 991218 - E - 00/06.02 68/104

Group AP200 Code 280B
A 31.7
1.25"
4x18 DIN6885
B
F Depth 13-.51"
.157"x.708"
106,4 11
12
4.2"
.47" .43"
3.25"-3.248" DIA
ø 82.55 -0.05
.63"
15,9
0
4.47"
113.5
0
d 6.4 15.875 -0.025
130,5 .25" 84
.625"-.624"
5.14" 3.31"
D +0.03
17.7 -0.2 3.97 0
.7"-.69"
0
.158"-.156"
1/4"-28 UNF

Type
cm3/rev
AP200/4.5 4.3
AP200/6.5 6.3 82.5 3.23 39.5 1.55 15 .59

AP200/8.5 8.3
AP200/11 10.95
98 5
98.5 39
3.9 47 5 1.87
47.5 1 87 40 1 58
1.58 M6X1 13 5
13.5 .53
53 35 1 38
1.38 M6X1
AP200/15 14.95
AP200/19 18.9 110.5 4.35 53.5 2.11 20 .79

AP200/22 21.9
115 4 53 55.5
4.53 55 5 2.18
2 18
AP200/26 25.9
Accessories

AP200/4.5 D 200.1021.802.01 AP200/4.5 S 200.1021.803.02 RF221
AP200/6.5 D 200.1022.802.01 AP200/6.5 S 200.1022.803.01 RF262
D S
AP200/8.5 D 200.1023.802.01 AP200/8.5 S 200.1023.803.01 RF216
AP200/11 D 200.1024.802.10 AP200/11 S 200.1024.803.01 RF252
AP200/15 D 200.1025.802.01 AP200/15 S 200.1025.803.01 RF217
AP200/19 D 200.1026.802.01 AP200/19 S 200.1026.803.01 RF220
AP200/22 D 200.1027.802.01 AP200/22 S 200.1027.803.01
AP200/26 D 200.1028.802.01 AP200/26 S 200.1028.803.01
200 - P - 991218 - E - 00/06.02 69/104

AP200 with built–in valves
AP200 pumps (except pump code 259) can be provided by For the exemple composition product code see page
a rear cover with a built in flow control valve VR , priority valve 99/104.
VP or pressure relief valve VM.
VRE VRI VP VME VMI
VRE VRI VP VME VMI
Q1 Q1 Q1 P P
T Q2 T
T
T
Q1 Regulated delivery Q1 Regulated delivery Q1 Regulated delivery T External relief valve Internal relief valve
T Exceeding delivery with Exceeding delivery Q2 Exceeding delivery, return to tank T return to pump suction
external line to tank T internal to pump suction external pressurizable line
VP 26
40 VRE 12 VRI 12
1.02"
1.57" .47" .47"
2.34"
' Q1 ' Q1 ' Q1

60
1.34"
34
-5 -5 -5
80 +20 80 +20 80 +20
b Nm Nm Nm
T Q2 b
M18x1.5 M18x1.5 M18x1.5
Standard setting values for VR, VP, VM

VRE
Type 02 03 05 06 08 09 12 16 19 23 Type VP 02 03 05 06 08 10 13 16 20 24
VRI
+15% +15%
l/min 2 3.5 5 6 7.5 9 12 16 19 23 l/min 2.5 3.5 5 6 8.5 10.5 13 16 20 24
-10% -10%
VME 22 VMI 22
.86" .86"
-5 -5
60 +15 60 +15 VME
Nm Type 06 15
Nm VMI
b
40 T Bar ±10% 60 150
1.57" M18x1.5
(spring YE with adjustment range from 30÷ 80 bar)
All the above drawings refer to clockwise rotation pumps.
( spring GR with adjustment range from 70÷ 210 bar)
For the remainig dimensions look at the correspondent pump code.
200 - P - 991218 - E - 00/06.02 70/104

A 40
1.58" ø16 200.6612.0003.0
Depth 13-.51"
C B 28 12 .63" DIA
1.1" .47"
71.5 14 89
1.436"-1.434" DIA
M 12 x1,5
2.81" 3.5"
ø 36.5f8
.55"
F
32,5
1.28"
4.47"
113,5
3.78"
96
.63"
8,5
15,9
.33"
ø 16,65
.66" DIA
d d 5 Taper 1:8 84
19
.20" 60+10 Nm 3.3"
D D 12
.47"
3.2 h8
Suction Pressure .126"-.125"
Displacement
.37"
9.4
d D F d D F
cm3/rev mm inch. mm inch. mm mm inch. mm inch. mm
4.5
6.5 13.5 .53 30 1.2 6x1
8.5 13.5 .53 30 1.2 6x1
11 M max.= 85 Nm
15
19 19 .75 40 1.57 8x1.25
22 19 .75 40 1.57 8x1.25
26
cm3/rev mm inch mm inch mm inch cm3/rev mm inch mm inch mm inch
4.5+4.5 22+11
228 9 115 45
4.5
6.5+4.5 22+15
6.5+6.5 22+19 238 9.4 121 4.7
175 5
175.5 7 40 5
40.5 16
1.6 90 5
90.5 3 56
3.56
8.5+4.5 22+22 243 9.5 123 4.8
8.5+6.5 26+4.5
8.5+8.5 26+6.5 208 8.2 107 4.2
56 5
56.5 23
2.3
11+4.5 26+8.5
11+6.5 191.5 7.5 98.5 3.88 26+11
228 9 115 45
4.5
11+8.5 26+15
48 5
48.5 2
11+11 211.5 8.3 106.5 4.2 26+19 238 9.4 121 4.7
15+4.5 26+22
191 5
191.5 75
7.5 98 5
98.5 3 88
3.88 243 95
9.5 123 48
4.8
15+6.5 26+26
15+8.5 191.5 7.5 98.5 3.88
15+11 48.5 2 Accessories
211 5
211.5 83
8.3 106 5
106.5 42
4.2
15+15
Flange Splined
19+4.5
connectors couplings
19+6.5 203.5 8 104.5 4
RF201 RF223 GSH-2-14
19+8.5
54 5
54.5 21
2.1 RF202 RF224 GSH-2-15
19+11
223 5
223.5 88
8.8 112 5
112.5 4 43
4.43
19+15 RF207 RF225 GSH-2-18
19+19 233.5 9.2 118.5 4.7
RF210 RF238
22+4.5
RF212 RF246
22+6.5 208 8.2 56.5 2.3 107 4.2
22+8.5 RF213 RF251
See page 99/104 for an example of the ordering code.
200 - P - 991218 - E - 00/06.02 71/104

A 40
1.58" ø16 200.6612.0003.0
C B 28 12 .63" DIA
1.1" .47"
71.5 14 89
1.436"-1.434" DIA
M 12 x1,5
2.81" 3.5"
ø 36.5f8
.55"
1.28"
32,5
4.47"
113,5
3.78"
96
15,9
.63"
.33"
8,5
ø 16,65
.66" DIA
G 5 Taper 1:8 84
G
Suction-Pressure .20" 19 3.3"
60+10 Nm
22 27
12
50+5 Nm 3/8" 60+10 Nm 1/2"
.47"
32 100+10 Nm 3/4"
Suction Pressure
Displacement 3.2 h8
G G
.126"-.125"
cm3/rev BSPP BSPP
.37"
9.4
4.5
6.5 3/8"
8.5 3/8"
11 1/2"
15
M max.= 85 Nm
19
22 3/4" 1/2"
26
4.5+4.5 22+11
228 9 115 45
4.5
6.5+4.5 22+15
6.5+6.5 22+19 238 9.4 121 4.7
175 5
175.5 7 40 5
40.5 16
1.6 90 5
90.5 3 56
3.56
8.5+4.5 22+22 243 9.5 123 4.8
8.5+6.5 26+4.5
8.5+8.5 26+6.5 208 8.2 107 4.2
56 5
56.5 23
2.3
11+4.5 26+8.5
11+6.5 191.5 7.5 98.5 3.88 26+11
228 9 115 45
4.5
11+8.5 26+15
48 5
48.5 2
11+11 211.5 8.3 106.5 4.2 26+19 238 9.4 121 4.7
15+4.5 26+22
191 5
191.5 75
7.5 98 5
98.5 3 88
3.88 243 95
9.5 123 48
4.8
15+6.5 26+26
15+8.5 191.5 7.5 98.5 3.88
15+11 48.5 2
211 5
211.5 83
8.3 106 5
106.5 42
4.2
15+15
19+4.5
19+6.5 203.5 8 104.5 4 Accessories
19+8.5
54 5
54.5 21
2.1
19+11 Flange Splined
223 5
223.5 88
8.8 112 5
112.5 4 43
4.43
19+15 connectors couplings
19+19 233.5 9.2 118.5 4.7 GSH-2-14
22+4.5
GSH-2-15
22+6.5 208 8.2 56.5 2.3 107 4.2
22+8.5 GSH-2-18
200 - P - 991218 - E - 00/06.02 72/104

A 37.7
1.48" ø16 DIN6888
C B 24.7 .63" DIA
.97"
72 15 13 90
2.83" .6" .51" 3.54"
M 12 x1,5
3.147"-3.145.DIA
15.9
.63"
1.36"
34.5
ø 80 e8
4.65"
118
3.94"
100
.354"
9
Depth 13-.51" F
ø 17
.67" DIA
Taper 1:5
d d 7.2 84
.28" 3.31"
D D 7.7
19 60+10 Nm
.30"
Suction Pressure 3 h8
Displacement .118"-.117"
d D F d D F
.37"
9.5
4.5
6.5 15 .6
8.5
11 40 1.57 6x1 15 .6 35 1.38 6x1
15
20 .78 M max.= 85 Nm
19
22
4.5+4.5 22+11 229 9 57.5 2.3 115 4.5
6.5+4.5 22+15 229 9 115 4.5
6.5+6.5 22+19 239 9.4 57.5 2.3 121 4.7
176 5
176.5 7 41 5
41.5 16
1.6 90 5
90.5 3 56
3.56
8.5+4.5 22+22 244 9.6 123 4.8
8.5+6.5
8.5+8.5
11+4.5
11+6.5 192.5 7.6 98.5 3.88
11+8.5
49 5
49.5 2
11+11 212.5 8.4 106.5 4.2
15+4.5
192 5
192.5 76
7.6 98 5
98.5 3 88
3.88
15+6.5
15+8.5 192.5 7.6 98.5 3.88
15+11 49.5 2 Accessories
212 5
212.5 84
8.4 106 5
106.5 42
4.2
15+15
Flange Splined
19+4.5 connectors couplings
19+6.5 204.5 8 104.5 4
RF221 GSH-2B-14
19+8.5
55 5
55.5 22
2.2 RF262 GSH-2B-15
19+11
224 5
224.5 88
8.8 112 5
112.5 4 43
4.43
19+15 RF216 GSH-2B-18
19+19 234.5 9.2 118.5 4.7
RF252
22+4.5
RF217
22+6.5 209 8.2 57.5 2.3 107 4.2
22+8.5 RF220
200 - P - 991218 - E - 00/06.02 73/104

A 23.5
.925"
.645"-.65" DIA
C B 14
ø 16.5 h11
.55"
72 15 90
2.83" .6" 3.54"
3.147"-3.145. DIA
15.9
.63"
1.36"
34.5
ø 80 e8
3.94"
4.65"
118
100
.354"
9
F
Depth 13-.51"
B 17x14
DIN 5482
d d 7.2 84
.28" 3.31"
D D
Suction Pressure
Displacement
d D F d D F
4.5
15 .6
6.5
8.5
11 40 1.57 6x1 15 .6 35 1.38 6x1
15
20 .78
19 M max.= 85 Nm
22
4.5+4.5 22+11
229 9 115 45
4.5
6.5+4.5 22+15
57 5
57.5 23
2.3
6.5+6.5 22+19 239 9.4 121 4.7
176 5
176.5 7 41 5
41.5 16
1.6 90 5
90.5 3 56
3.56 22+22 244 9.6 123 4.8
8.5+4.5
8.5+6.5
8.5+8.5
11+4.5
11+6.5 192.5 7.6 98.5 3.88
11+8.5
49 5
49.5 2
11+11 212.5 8.4 106.5 4.2
15+4.5
192 5
192.5 76
7.6 98 5
98.5 3 88
3.88
15+6.5
15+8.5 192.5 7.6 98.5 3.88
15+11 Accessories
49.5 2
212 5
212.5 84
8.4 106 5
106.5 42
4.2
15+15 Flange Splined
19+4.5 connectors couplings
19+6.5 204.5 8 104.5 4 RF221
19+8.5
55 5
55.5 22
2.2 RF262
19+11
224 5
224.5 88
8.8 112 5
112.5 4 43
4.43 RF216
19+15
19+19 234.5 9.2 118.5 4.7 RF252
22+4.5
RF217
22+6.5 209 8.2 57.5 2.3 107 4.2
22+8.5 RF220
200 - P - 991218 - E - 00/06.02 74/104

A 40,5
1.59" ø16 DIN6888
C B 27,5 .63"DIA
60
1.967"-1.966" DIA
1.08"
M 12 x1,5
2.36"
ø 50 f8
X
7.2 13
.47"
.563"
14.3
15.9
.63"
3.94"
2.38"
60.4
100
F
Depth 13-.51"
ø 17
.67" DIA
Taper 1:5 84
3.31"
19 60+10 Nm
10.5 d d 10,5
.413" .413"
8 D D
.315" X
3 h8
Suction Pressure
.37"
.118"-.117"
9.5
Displacement
d D F d D F
4.5
6.5 15 .59
8.5
11 40 1.58 6x1 15 .59 35 1.38 6x1
M max.= 85 Nm To utilize M10x1.5 DIN931
15
20 .79
19 17 45+5 Nm
22
4.5+4.5 22+11
213 84
8.4 115 45
4.5
6.5+4.5 22+15
55 22
2.2
6.5+6.5 22+19 225 8.8 121 4.7
164 5
164.5 65
6.5 38 5
38.5 15
1.5 90 5
90.5 3 56
3.56
8.5+4.5 22+22 230 9 123 4.8
8.5+6.5
8.5+8.5
11+4.5
11+6.5 180.5 7 98.5 3.88
11+8.5
46 5
46.5 18
1.8
11+11 196.5 7.7 106.5 4.2
15+4.5
180 5
180.5 7 98 5
98.5 3 88
3.88
15+6.5
15+8.5 180.5 7 98.5 3.88
15+11 46.5 1.8
196 5
196.5 77
7.7 106 5
106.5 42
4.2 Accessories
15+15
19+4.5 Flange Splined
19+6.5 192.5 7.5 104.5 4
RF221 GSH-2B-14
19+8.5
52 5
52.5 2
19+11 RF262 GSH-2B-15
208 5
208.5 82
8.2 112 5
112.5 4 43
4.43
19+15 RF216 GSH-2B-18
19+19 220.5 8.7 118.5 4.7
RF252
22+4.5
RF217
22+6.5 197 7.7 55 2.2 107 4.2
22+8.5 RF220
200 - P - 991218 - E - 00/06.02 75/104

A 40,5
1.59" ø16 DIN6888
C B 27,5 .63" DIA
60
1.967"-1.966" DIA
1.08"
M 12 x1,5
2.36"
ø 50 f8
X
7.2 13
.47"
.563"
14.3
15.9
.63"
3.94"
2.38"
60.4
100
F
Depth 13-.51"
ø 17
.67" DIA
Taper 1:5 84
3.31"
10.5
19 60+10 Nm
d d 10,5
.413" .413"
8 D D
.315"
X
3 h8
.37"
Suction Pressure
9.5
.118"-.117"
Displacement
d D F d D F
4.5
6.5 15 .59
8.5
40 1.58 6x1 15 .59 35 1.38 6x1 M max.= 85 Nm To utilize M10x1.5 DIN931
11
15
20 .79 17 45+5 Nm
19
22
4.5+4.5 22+11
213 84
8.4 115 45
4.5
6.5+4.5 22+15
55 22
2.2
6.5+6.5 22+19 225 8.8 121 4.7
164 5
164.5 65
6.5 38 5
38.5 15
1.5 90 5
90.5 3 56
3.56
8.5+4.5 22+22 230 9 123 4.8
8.5+6.5
8.5+8.5
11+4.5
11+6.5 180.5 7 98.5 3.88
11+8.5
46 5
46.5 18
1.8
11+11 196.5 7.7 106.5 4.2
15+4.5
180 5
180.5 7 98 5
98.5 3 88
3.88
15+6.5
15+8.5 180.5 7 98.5 3.88
15+11 46.5 1.8
196 5
196.5 77
7.7 106 5
106.5 42
4.2 Accessories
15+15
19+6.5
192.5 7.5 104.5 4
19+8.5 RF221 GSH-2B-14
52 5
52.5 2
19+11 RF262 GSH-2B-15
208 5
208.5 82
8.2 112 5
112.5 4 43
4.43
19+15 RF216 GSH-2B-18
19+19 220.5 8.7 118.5 4.7
RF252
22+4.5
RF217
22+6.5 197 7.7 55 2.2 107 4.2
22+8.5 RF220
200 - P - 991218 - E - 00/06.02 76/104

A
7.2
60 C B .28"
2.36" 3.2
-0.060 .126"
8 -0.075 X
2
.313"-.312"
.563"
2.046"-2.045" DIA
.079"
14.3
15.9
.63"
1.882"DIA
1.5"DIA
ø 52 f7
ø 47.8
ø 38
3.94"
2.38"
60.4
100
.35"
.7"DIA
ø 17.6
9
F
Depth 13-.51"
10.5 2.7 84
3.31"
.413" d d .106"
1.5 OR3187 - 70Sh
.06"
D D
Motor-shaft page 54 6.5
.256"
To utilize
M10x1.5 DIN931
X
17 45+5 Nm
Suction Pressure
Displacement
d D F d D F
4.5
6.5 15 .59 M max.= 85 Nm
8.5
40 1.58 M6x1 15 .59 35 1.38 M6x1
11
15 20 .79
19
Displacement A B C
cm3/rev mm inch mm inch mm inch
4.5+4.5
6.5+4.5
6.5+6.5
164 5
164.5 65
6.5 38 5
38.5 15
1.5 90 5
90.5 3 56
3.56
8.5+4.5
8.5+6.5
8.5+8.5
11+4.5
11+6.5 180.5 7 98.5 3.88
11+8.5
46 5
46.5 18
1.8
11+11 196.5 7.7 106.5 4.2
15+4.5
180 5
180.5 7 98 5
98.5 3 88
3.88 Accessories
15+6.5
15+8.5 180.5 7 98.5 3.88 Flange Splined
15+11 46.5 1.8 connectors couplings
196 5
196.5 77
7.7 106 5
106.5 42
4.2
15+15 RF221
19+4.5 RF262
19+6.5 192.5 7.5 104.5 4
RF216
19+8.5
52 5
52.5 2 RF252
19+11
208 5
208.5 82
8.2 112 5
112.5 4 43
4.43 RF217
19+15
19+19 220.5 8.7 118.5 4.7 RF220
200 - P - 991218 - E - 00/06.02 77/104

A 31,7
1.25"
106,4 C B 14
4.2" .55"
12 11
.47" .43"
3.25"-3.248" DIA
ø 82.55 -0.05
0
4.47"
113.5
15,9
.63"
6.4
130,5 G G 84
Suction-Pressure .25"
5.14" Suction-Pressure 3.31"
100+10 Nm 1-1/16 12UNF
65+10 Nm 7/8 14UNF SAE J 498-9T

16/32 DP
FLAT ROOT SIDE FIT
Suction Pressure
Displacement CLASS 1 FIT
G G
cm3/rev 12UN 14UNF
4.5
6.5
8.5
11 1-1/16 7/8 M max.= 85 Nm
15
19
22
26
4.5+4.5 22+11
227 89
8.9 115 45
4.5
6.5+4.5 22+15
6.5+6.5 22+19 237 9.3 121 4.7
174 5
174.5 68
6.8 39 5
39.5 15
1.5 90 5
90.5 3 56
3.56
8.5+4.5 22+22 242 9.5 123 4.8
8.5+6.5 26+4.5
8.5+8.5 26+6.5 207 8.1 107 4.2
55 5
55.5 22
2.2
11+4.5 26+8.5
11+6.5 190.5 7.5 98.5 3.88 26+11
227 89
8.9 115 45
4.5
11+8.5 26+15
47 5
47.5 19
1.9
11+11 210.5 8.3 106.5 4.2 26+19 237 9.3 121 4.7
15+4.5 26+22
190 5
190.5 75
7.5 98 5
98.5 3 88
3.88 242 95
9.5 123 48
4.8
15+6.5 26+26
15+8.5 190.5 7.5 98.5 3.88
15+11 47.5 1.9
210 5
210.5 83
8.3 106 5
106.5 42
4.2
15+15
19+4.5
19+6.5 202.5 7.9 104.5 4
19+8.5
53 5
53.5 21
2.1
19+11
222 5
222.5 87
8.7 112 5
112.5 4 43
4.43
19+15
19+19 232.5 9 118.5 4.7
22+4.5
22+6.5 207 8.1 55.5 2.2 107 4.2
22+8.5
200 - P - 991218 - E - 00/06.02 78/104

A 31.7
1.25"
106,4 C B 4x18 DIN6885
4.2" .157"x.708"
12 11
.47"
.43"
3.25"-3.248" DIA
ø 82.55 -0.05
0
4.47"
113.5
15,9
.63"
G G 6.4
130,5 .25" 84
Suction-Pressure Suction-Pressure 3.31"
5.14"
100+10 Nm 1-1/16 12UNF
65+10 Nm 7/8 14UNF 0

15.875 -0.025
Suction Pressure .625"-.624"

Displacement
17.7 -0.2
.7"-.69"
+0.03
G G 3.97
0
0
cm3/rev 12UN 14UNF .158"-.156"
4.5
6.5
8.5
1/4"-28 UNF
11 1-1/16 7/8 M max.= 85 Nm
15
19
22
26
4.5+4.5 22+11
227 89
8.9 115 45
4.5
6.5+4.5 22+15
6.5+6.5 22+19 237 9.3 121 4.7
174 5
174.5 68
6.8 39 5
39.5 15
1.5 90 5
90.5 3 56
3.56
8.5+4.5 22+22 242 9.5 123 4.8
8.5+6.5 26+4.5
8.5+8.5 26+6.5 207 8.1 107 4.2
55 5
55.5 22
2.2
11+4.5 26+8.5
11+6.5 190.5 7.5 98.5 3.88 26+11
227 89
8.9 115 45
4.5
11+8.5 26+15
47 5
47.5 19
1.9
11+11 210.5 8.3 106.5 4.2 26+19 237 9.3 121 4.7
15+4.5 26+22
190 5
190.5 75
7.5 98 5
98.5 3 88
3.88 242 95
9.5 123 48
4.8
15+6.5 26+26
15+8.5 190.5 7.5 98.5 3.88
15+11 47.5 1.9
210 5
210.5 83
8.3 106 5
106.5 42
4.2
15+15
19+4.5
19+6.5 202.5 7.9 104.5 4
19+8.5
53 5
53.5 21
2.1
19+11
222 5
222.5 87
8.7 112 5
112.5 4 43
4.43
19+15
19+19 232.5 9 118.5 4.7
22+4.5
22+6.5 207 8.1 55.5 2.2 107 4.2
22+8.5
200 - P - 991218 - E - 00/06.02 79/104

Group AP200 Code 2287S–B
A 31.7
1.25"
Depth 13-.51"
106,4 C B 14
4.2" .55"
12 11
.47" .43"
3.25"-3.248" DIA
-0.05
F
0
4.47"
113.5
ø 82.55
15,9
.63"
130,5 d d 6.4 84
5.14" .25" 3.31"
D D
SAE J 498-9T
16/32 DP
FLAT ROOT SIDE FIT
Suction Pressure CLASS 1 FIT
Displacement
d D F d D F
4.5
6.5 15 .6
8.5
11 40 1.57 6x1 15 .6 35 1.38 6x1
15
19 20 .78
22 M max.= 85 Nm
26
4.5+4.5 22+11
227 89
8.9 115 45
4.5
6.5+4.5 22+15
6.5+6.5 22+19 237 9.3 121 4.7
174 5
174.5 68
6.8 39 5
39.5 15
1.5 90 5
90.5 3 56
3.56
8.5+4.5 22+22 242 9.5 123 4.8
8.5+6.5 26+4.5
8.5+8.5 26+6.5 207 8.1 107 4.2
55 5
55.5 22
2.2
11+4.5 26+8.5
11+6.5 190.5 7.5 98.5 3.88 26+11
227 89
8.9 115 45
4.5
11+8.5 26+15
47 5
47.5 19
1.9
11+11 210.5 8.3 106.5 4.2 26+19 237 9.3 121 4.7
15+4.5 26+22
190 5
190.5 75
7.5 98 5
98.5 3 88
3.88 242 95
9.5 123 48
4.8
15+6.5 26+26
15+8.5 190.5 7.5 98.5 3.88
15+11 47.5 1.9
210 5
210.5 83
8.3 106 5
106.5 42
4.2 Accessories
15+15
19+6.5 202.5 7.9 104.5 4
19+8.5
RF221
53 5
53.5 21
2.1
19+11 RF262
222 5
222.5 87
8.7 112 5
112.5 4 43
4.43
19+15 RF216
19+19 232.5 9 118.5 4.7
RF252
22+4.5
RF217
22+6.5 207 8.1 55.5 2.2 107 4.2
22+8.5 RF220
200 - P - 991218 - E - 00/06.02 80/104

Group AP200 Code 2280–B
A 31.7
1.25"
106,4 C B 4x18 DIN6885
Depth 13-.51"
4.2" .157"x.708"
12 11
.47" .43"
3.25"-3.248" DIA
ø 82.55 -0.05
F
0
4.47"
113.5
15,9
.63"
6.4
130,5 d d .25" 84
5.14" 3.31"
D D
0
Suction Pressure 15.875 -0.025
Dispacement .625"-.624"
d D F d D F
cm3/rev
17.7 -0.2
mm inch. mm inch. mm mm inch. mm inch. mm +0.03
.7"-.69"
3.97
0
0
4.5
15 .6 .158"-.156"
6.5
8.5
11 40 1.57 6x1 15 .6 35 1.38 6x1
15 1/4"-28 UNF
20 .78
19 M max.= 85 Nm
22
26
4.5+4.5 22+11
227 89
8.9 115 45
4.5
6.5+4.5 22+15
6.5+6.5 22+19 237 9.3 121 4.7
174 5
174.5 68
6.8 39 5
39.5 15
1.5 90 5
90.5 3 56
3.56
8.5+4.5 22+22 242 9.5 123 4.8
8.5+6.5 26+4.5
8.5+8.5 26+6.5 207 8.1 107 4.2
55 5
55.5 22
2.2
11+4.5 26+8.5
11+6.5 190.5 7.5 98.5 3.88 26+11
227 89
8.9 115 45
4.5
11+8.5 26+15
47 5
47.5 19
1.9
11+11 210.5 8.3 106.5 4.2 26+19 237 9.3 121 4.7
15+4.5 26+22
190 5
190.5 75
7.5 98 5
98.5 3 88
3.88 242 95
9.5 123 48
4.8
15+6.5 26+26
15+8.5 190.5 7.5 98.5 3.88
15+11 47.5 1.9
210 5
210.5 83
8.3 106 5
106.5 42
4.2
15+15 Accessories
19+6.5 202.5 7.9 104.5 4 connectors couplings
19+8.5 RF221
53 5
53.5 21
2.1
19+11
222 5
222.5 87
8.7 112 5
112.5 4 43
4.43
RF262
19+15
RF216
19+19 232.5 9 118.5 4.7
RF252
22+4.5
22+6.5 207 8.1 55.5 2.2 107 4.2
RF217
22+8.5 RF220
200 - P - 991218 - E - 00/06.02 81/104

Multiple gear pumps
511 901 901 501
Lubricate with MoS2 base grease 200.5307.60801 200.5216.03519
Schnorr 8.4x13x1.2/0.8 M8x1.25x45 DIN912
6 15+5 Nm
200.5252.03551
M8x1.25x6.5 DIN934
Front pump 501
200.6614.0003.0
B17x14
DIN5482
Mmax.= 85 Nm
Intermediate pump 901

B 17x14 Mmax.= 85 Nm
200.6614.0003.0 200.6614.0003.0
Rear pump 511
200.6614.0003.0
B 17x14 Mmax.= 85 Nm
The 501, 901, and 511 code pumps are sold as single pre–assembled and tested units. They can be used in a variety of combinations in double, triple,
quadruple pumps, etc.. In the case of one or more pumps with operation under pressure or at the operating limits, the recommendations indicated
on page 9/104 are to be observed.
200 - P - 991218 - E - 00/06.02 82/104

A
ø16 200.6612.0003.0
24 B 40 .63" DIA
.94" 1.58"
Depth 13-.51"
14 28 12 89
71.5
M 12 x1,5
1.436"-1.434" DIA
2.81" .55" 1.1" .47" 3.5"
ø 36.5 f8
15,9
1.28"
.63"
1.26"
32,5
32
F
3.78"
4.45"
3.77"
113
95.8
96
.33"
8,5
7
.27"
ø 16,65
.66" DIA
.33"
8.5
72
17 d 5 Taper 1:8 19 2.83"
60+10 Nm
.67" .20"
84
3.2 h8 3.3"
D 12
.126"-.125"
.47"
.37"
9.4

Displacement
Di l t
cm3/rev
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 85 5
85.5 3 36 40.3
3.36 40 3 1.59
1 59 13.5
13 5 .53
53 30 1 18
1.18 M6X1
AP200/8 5
AP200/8.5 83
8.3 13 5
13.5 .53
53 30 1 18
1.18 M6X1
AP200/11 10 95
10.95
101 5
101.5 4 48 3 1.90
48.3 1 90
AP200/15 14 95
14.95
AP200/19 18 9
18.9 113 5
113.5 4 46 54.3
4.46 54 3 2.14
2 14 19 .75
75 40 1 58
1.58 M8X1 25
M8X1.25
AP200/22 21 9
21.9 19 .75
75 40 1 58
1.58 M8X1 25
M8X1.25
118 4 64 56.5
4.64 56 5 2.22
2 22
AP200/26 25 9
25.9
Accessories

AP200/4.5 D 200.7483.1058.0 AP200/4.5 S 200.7483.1059.0 RF223 GSH-2-14
AP200/6.5 D 200.7483.2055.0 AP200/6.5 S 200.7483.2056.0 RF224 GSH-2-15
D S
AP200/8.5 D 200.7483.3058.0 AP200/8.5 S 200.7483.3059.0 RF225 GSH-2-18
AP200/11 D 200.7483.4058.0 AP200/11 S 200.7483.4059.0 RF238 200.6614.0003.0
AP200/15 D 200.7483.5056.0 AP200/15 S 200.7483.5057.0 RF246
AP200/19 D 200.7483.6057.0 AP200/19 S 200.7483.6058.0 RF251
AP200/22 D 200.7483.7055.0 AP200/22 S 200.7483.7056.0
AP200/26 D 200.7483.8047.0 AP200/26 S 200.7483.8048.0
200 - P - 991218 - E - 00/06.02 83/104

24 24 89
Depth 13-.51"
.94" .94" 3.5"
1.26"
.63"
15.9
32
4.45"
3.77"
113
95.8
7
.33"
8.5
.27"
72 17 d 17 84
2.83" .67" .67" 3.3"

Displacement
Di l t
cm3/rev
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 90 5
90.5 3 56 45.5
3.56 45 5 1.79
1 79 13.5
13 5 .53
53 30 1 18
1.18 M6X1
AP200/8 5
AP200/8.5 83
8.3 13 5
13.5 .53
53 30 1 18
1.18 M6X1
AP200/11 10 95
10.95
106 5
106.5 42
4.2 53 5 2.10
53.5 2 10
AP200/15 14 95
14.95
AP200/19 18 9
18.9 112 5
112.5 4 56 59.5
4.56 59 5 2.34
2 34 19 .75
75 40 1 58
1.58 M8X1 25
M8X1.25
AP200/22 21 9
21.9 19 .75
75 40 1 58 M8X1.25
1.58 M8X1 25
123 4 84 61.5
4.84 61 5 2.40
2 40
AP200/26 25 9
25.9
Accessories

AP200/4.5 D 200.7483.1062.0 AP200/4.5 S 200.7483.1063.0 RF223 200.6614.0003.0
AP200/6.5 D 200.7483.2059.0 AP200/6.5 S 200.7483.2060.0 RF224
D S
AP200/8.5 D 200.7483.3062.0 AP200/8.5 S 200.7483.3063.0 RF225
AP200/11 D 200.7483.4062.0 AP200/11 S 200.7483.4063.0 RF238
AP200/15 D 200.7483.5060.0 AP200/15 S 200.7483.5061.0 RF246
AP200/19 D 200.7483.6061.0 AP200/19 S 200.7483.6062.0 RF251
AP200/22 D 200.7483.7059.0 AP200/22 S 200.7483.7060.0
AP200/26 D 200.7483.8051.0 AP200/26 S 200.7483.8052.0
200 - P - 991218 - E - 00/06.02 84/104

Depth 13-.51"
24
.94" 84
3.3"
15,9
.63"
4.45"
3.77"
113
95.8
72
89 d 17
.67" 2.38"
3.5"

Displacement
Di l t
cm3/rev
AP200/4 5
AP200/4.5 43
4.3
AP200/6 5
AP200/6.5 63
6.3 90 3 54 45.5
3.54 45 5 1.79
1 79 13.5
13 5 .53
53 30 1 18
1.18 M6X1
AP200/8 5
AP200/8.5 83
8.3 13 5
13.5 .53
53 30 1 18
1.18 M6X1
AP200/11 10 95
10.95
110 43
4.3 53 5 2.10
53.5 2 10
AP200/15 14 95
14.95
AP200/19 18 9
18.9 120 4 72 59.5
4.72 59 5 2.34
2 34 19 .75
75 40 1 58
1.58 M8X1 25
M8X1.25
AP200/22 21 9
21.9 19 .75
75 40 1 58 M8X1.25
1.58 M8X1 25
125 4 92 61.5
4.92 61 5 2.40
2 40
AP200/26 25 9
25.9
Accessories

AP200/4.5 D 200.7483.1060.0 AP200/4.5 S 200.7483.1061.0 RF223 200.6614.0003.0
AP200/6.5 D 200.7483.2057.0 AP200/6.5 S 200.7483.2058.0 RF224
D S
AP200/8.5 D 200.7483.3060.0 AP200/8.5 S 200.7483.3061.0 RF225
AP200/11 D 200.7483.4060.0 AP200/11 S 200.7483.4061.0 RF238
AP200/15 D 200.7483.5058.0 AP200/15 S 200.7483.5059.0 RF246
AP200/19 D 200.7483.6059.0 AP200/19 S 200.7483.6060.0 RF251
AP200/22 D 200.7483.7057.0 AP200/22 S 200.7483.7058.0
AP200/26 D 200.7483.8049.0 AP200/26 S 200.7483.8050.0
200 - P - 991218 - E - 00/06.02 85/104

Cu. In. P1 P2 P3
AP300/27 27.0 1.647 220 3150 250 3600 280 4000 600 800 3000 3500
AP300/31 31.0 1.891 220 3150 250 3600 280 4000 600 800 3000 3500
AP300/38 38.0 2.318 220 3150 250 3600 280 4000 600 800 2500 3000
AP300/45 45.0 2.745 200 2900 230 3300 260 3700 600 800 2500 3000
AP300/53 53.0 3.233 200 2900 230 3300 260 3700 600 800 2500 3000
AP300/63 63.0 3.843 180 2600 210 3000 240 3400 550 700 2500 3000
AP300/75 75.0 4.575 170 2400 190 2700 220 3150 550 700 2000 2500
AP300/93 93.0 5.673 150 2100 170 2400 200 2900 500 650 2000 2500
80+5 Nm Max torque allowed to the shaft
1:8 M max= 230 Nm **8
M max= 270 **7

SAE J 498-9T 16/32 DP
M max= 185 Nm **0
Notes:
200 - P - 991218 - E - 00/06.02 86/104

A 47 ø19 DIN6888
1.849" .748"DIA
120 B 32.5
1.999"-1.997" DIA
4.72" 1.28"
50.80 f8 -0.076
-0.30
98 F 5 118
3.855" .197" 4.64"
M14x1.5
14.5
.57"
.926"
23.55
2.065"
1.652"
52.5
42
5.979"
5.035"
152
128
.413"
10.5
ø 21.59
.85"DIA
Taper 1:8
22 80+20 Nm
d 15
12.15 -0.15
.59"
.478"-.472"
0
D 11.2 ±0.03 0
4h9 -0.03
.45"-.43" .156"-.157"

DisplaceĆ
Type ment A B d D F d D F
cm3/rev
AP300/27 27 126.0 4.96 64.0 2.51
AP300/31 31 129.0 5.07 65.0 2.55
AP300/38 38 133.5 5.25 67.5 2.65 27 1.06 51 2.00 M10X1.5 20 .78 40 1.56 M8X1.25
AP300/45 45 138.5 5.43 70.0 2.75
AP300/53 53 143.0 5.62 72.5 2.85
AP300/63 63 150.0 5.90 75.5 2.97
AP300/75 75 157.5 6.20 79.5 3.13 32 1.26 62 2.43 M12X1.75 27 1.06 51 2.00 M10X1.5
AP300/93 93 169.0 6.65 85.5 3.36
Accessories

AP300/27 D 200.1031.132.01 AP300/27 S 200.1031.133.01 RF233 GSH-3-18
AP300/31 D 200.1032.132.01 AP300/31 S 200.1032.133.01 RF261 GSH-3-20
D S
AP300/38 D 200.1033.132.01 AP300/38 S 200.1033.133.01 RF272
AP300/45 D 200.1034.132.01 AP300/45 S 200.1034.133.01 RF256
AP300/53 D 200.1035.132.01 AP300/53 S 200.1035.133.02 RF225
AP300/63 D 200.1036.132.02 AP300/63 S 200.1036.133.01 RF246
AP300/75 D 200.1037.132.01 AP300/75 S 200.1037.133.01 RF251
AP300/93 D 200.1038.132.01 AP300/93 S 200.1038.133.03
200 - P - 991218 - E - 00/06.02 87/104

A 47 ø19 DIN6888
1.849" .748" DIA
120 B 32.5
1.999"-1.997" DIA
50.80 f8 -0.076
4.72"
-0.30
1.28"
98 5 118
3.855" .197" 4.64"
M14x1.5
14.5
.57"
.926"
23.55
2.065"
1.652"
52.5
42
5.979"
5.035"
152
128
.413"
10.5
ø 21.59
.85" DIA
Taper 1:8
22 80+20 Nm
G 15
Suction-Pressure
12.15 -0.15
.59"
.478"-.472"
0
32
100+10 Nm 3/4" 11.2 ±0.03 0
4h9 -0.03
.45"-.43"
.156"-.157"
40 150+20 Nm 1"

Displacement
Di l t
Type A B G G
cm3/rev
mm inch mm inch BSPP BSPP
AP300/27 27 126.0 4.96 64.0 2.51
AP300/31 31 129.0 5.07 65.0 2.55
AP300/38 38 133.5 5.25 67.5 2.65
AP300/45 45 138.5 5.43 70.0 2.75
1" 3/4"
AP300/53 53 143.0 5.62 72.5 2.85
AP300/63 63 150.0 5.90 75.5 2.97
AP300/75 75 157.5 6.20 79.5 3.13
AP300/93 93 169.0 6.65 85.5 3.36
Accessories

AP300/27 D 200.1031.132.03 AP300/27 S 200.1031.133.07 GSH-3-18
AP300/31 D 200.1032.132.05 AP300/31 S 200.1032.133.03 GSH-3-20
D S
AP300/38 D 200.1033.132.02 AP300/38 S 200.1033.133.03
AP300/45 D 200.1034.132.03 AP300/45 S 200.1034.133.03
AP300/53 D 200.1035.132.04 AP300/53 S 200.1035.133.03
AP300/63 D 200.1036.132.01 AP300/63 S 200.1036.133.03
AP300/75 D 200.1037.132.02 AP300/75 S 200.1037.133.03
AP300/93 D 200.1038.132.02 AP300/93 S 200.1038.133.04
200 - P - 991218 - E - 00/06.02 88/104

A 41.2
1.622"
174 15
6.85" .59"
146 H 9.5 118

5.748" .374" 4.645"
4"- 3.998" DIA

.565"
.927"
14.3
ø 101.6 -0.05
23.55
0
6.3"
160
SAE J 498-13T
F B 33.3
16/32 DP
1.311"
FLAT ROOT SIDE FIT
CLASS 1 FIT.

Disp.
Disp
Type cm3/ A B H D E F H D E F
rev
mm inch mm inch mm inch mm inch mm inch UNC2B mm inch mm inch mm inch UNC2B
3/8" - 3/8" -
AP300/27 27 126.0 4.96 64.0 2.51 26.2 1.03 52.4 2.06 25 .99
16
22.2 .88 47.6 1.88 19 .75
16
AP300/31 31 129.0 5.07 65.0 2.55
AP300/38 38 133.5 5.25 67.5 2.65 7/16" 3/8" -

30.2 1.19 58.7 2.31 31 1.22 26.2 1.03 52.4 2.06 25 .99
- 14 16
AP300/45 45 138.5 5.43 70.0 2.75
AP300/53 53 143.0 5.62 72.5 2.85
AP300/63 63 150.0 5.90 75.5 2.97

1/2 -
1/2" 7/16
7/16"
35 7
35.7 1 40
1.40 70 2 76
2.76 38 15
1.5 30 2
30.2 1 19
1.19 58 7
58.7 2 31
2.31 31 1 22
1.22
AP300/75 75 158.0 6.22 79.5 3.13 13 - 14
AP300/93 93 169.0 6.65 85.5 3.36
Accessories

AP300/27 D 200.1031.862.01 AP300/27 S 200.1031.863.01 RFS249
AP300/31 D 200.1032.862.01 AP300/31 S 200.1032.863.01 RFS248
D S
AP300/38 D 200.1033.862.01 AP300/38 S 200.1033.863.01 RFS275
AP300/45 D 200.1034.862.01 AP300/45 S 200.1034.863.01 RFS250
AP300/53 D 200.1035.862.01 AP300/53 S 200.1035.863.01
AP300/63 D 200.1036.862.01 AP300/63 S 200.1036.863.01
AP300/75 D 200.1037.862.01 AP300/75 S 200.1037.863.01
AP300/93 D 200.1038.862.01 AP300/93 S 200.1038.863.01
200 - P - 991218 - E - 00/06.02 89/104

A 41.2
1.622"
174 15 6.4x24.6 200.6612.0005.0
6.85" .59" .25"x.97"
146 H 9.5 118

5.748" .374" 4.645"
.565"
4"- 3.998" DIA

14.3
.927"
ø 101.6 -0.05
23.55
0
6.3"
160
0
22.225 -0.025
F B 33.3
.984"-.983"
1.311" .875"-.874"
0
25 -0.2
6.375 -0.025
0
.251"-250"
1/4"-28 UNF

Disp.
Disp
Type cm3/ A B H D E F H D E F
rev
mm inch mm inch mm inch mm inch mm inch UNC2B mm inch mm inch mm inch UNC2B
3/8" - 3/8" -
AP300/27 27 126.0 4.96 64.0 2.51 26.2 1.03 52.4 2.06 25 .99
16
22.2 .88 47.6 1.88 19 .75
16
AP300/31 31 129.0 5.07 65.0 2.55
AP300/38 38 133.5 5.25 67.5 2.65 7/16" 3/8" -

30.2 1.19 58.7 2.31 31 1.22 26.2 1.03 52.4 2.06 25 .99
- 14 16
AP300/45 45 138.5 5.43 70.0 2.75
AP300/53 53 143.0 5.62 72.5 2.85
AP300/63 63 150.0 5.90 75.5 2.97

1/2 -
1/2" 7/16
7/16"
35 7
35.7 1 40
1.40 70 2 76
2.76 38 15
1.5 30 2
30.2 1 19
1.19 58 7
58.7 2 31
2.31 31 1 22
1.22
AP300/75 75 158.0 6.22 79.5 3.13 13 - 14
AP300/93 93 169.0 6.65 85.5 3.36
Accessories

AP300/27 D 200.1031.802.01 AP300/27 S 200.1031.803.01 RFS249
AP300/31 D 200.1032.802.01 AP300/31 S 200.1032.803.01 RFS248
D S
AP300/38 D 200.1033.802.01 AP300/38 S 200.1033.803.01 RFS275
AP300/45 D 200.1034.802.01 AP300/45 S 200.1034.803.01 RFS250
AP300/53 D 200.1035.802.01 AP300/53 S 200.1035.803.01
AP300/63 D 200.1036.802.01 AP300/63 S 200.1036.803.01
AP300/75 D 200.1037.802.01 AP300/75 S 200.1037.803.01
AP300/93 D 200.1038.802.01 AP300/93 S 200.1038.803.01
200 - P - 991218 - E - 00/06.02 90/104

Group AP300+AP200 Code 2218
A 47 ø19 DIN6888
1.85" .748" DIA
120
C B 32.5 118
ø 50.8 -0.03 f8
1.999"-1.997" DIA
4.725"
1.28" 4.65"
+0.07
98 F F 5
84
M14x1.5
3.86" 1.653"
.197" 3.31"
42
.927"
.626"
23.55
15.9
5.98"
5.04"
2.067"
152
128
.413"
52.5
10.5
ø 21.59
.85" DIA
Taper 1:8 22 80+20 Nm
d d 15
Max pressure (M max= 65 Nm) .59"
bar (PSI) D D 11.2
Pump
P1 P2 P3 .44"
.478"-.472"
12.15-0.15
180 210 230 0
AP200/15 (2600) (3000) (3300) 4 -0.03 h9
0
.157"-.156"
140 165 185
AP200/19
(2000) (2400) (2650)
120 145 165
AP200/22 (1700) (2050) (2350)
100 120 140
AP200/26 (1450) (1750) (2000)
AP300 Accessories
Displacement Suction Pressure Flange Splined
d D F d D F connectors couplings
cm3/rev.
/rev
mm inch mm inch mm mm inch mm inch mm RF233 GSH-3-18
27 RF261 GSH-3-20
31 RF272
38 27 1.06 51 2.01 10 20 .79 40 1.58 8 RF256
45 RF225
53 RF246
63 RF251
75 32 1.26 62 2.44 12 27 1.07 51 2.01 10
93
AP200 Accessories
Displacement Suction Pressure Flange Splined
d D F d D F connectors couplings
cm3/rev
mm inch mm inch mm mm inch mm inch mm RF223
4.5 RF224
6.5 13.5 .53 30 1.18 6 RF225
8.5 13.5 .53 30 1.18 6 RF238
11 RF246
15 RF251
19 19 .75 40 1.58 8
22 19 .75 40 1.58 8
26
200 - P - 991218 - E - 00/06.02 91/104

AP300/27 AP300/31 AP300/38 AP300/45

A B C A B C A B C A B C
mm mm mm mm mm mm mm mm mm mm mm mm
inch inch inch inch inch inch inch inch inch inch inch inch
AP200/4.5 215.5 64 103.5 218 65 105 222.5 67.5 107.5 227 69.8 109.5
AP200/6 5
AP200/6.5
AP200/8.5 8.5 2.52 4.08 8.6 2.56 4.14 8.76 2.66 4.23 8.94 2.75 4.31
AP200/11 230.5 64 111.5 233 65 113 237.5 67.5 115.5 242 69.8 117.5
AP200/15 9.08 2.52 4.39 9.2 2.56 4.45 9.35 2.66 4.55 9.53 2.75 4.63
240.5 64 117.5 243 65 119 247.5 67.5 121.5 252 69.8 123.5
AP200/19
9.47 2.52 4.62 9.57 2.56 4.69 9.75 2.66 4.78 9.92 2.75 4.86
AP200/22 245.5 64 120 248 65 121 252.5 67.5 123.5 257 69.8 126
AP200/26 9.67 2.52 4.72 9.76 2.56 4.76 9.95 2.66 4.86 10.12 2.75 4.96
AP300/53 AP300/63 AP300/75 AP300/93

A B C A B C A B C A B C
mm mm mm mm mm mm mm mm mm mm mm mm
inch inch inch inch inch inch inch inch inch inch inch inch
AP200/4.5 232.5 72.5 112 239 75.5 115.5 246.5 79.5 119.5 258.5 85.5 125
AP200/6 5
AP200/6.5
AP200/8.5 9.15 2.86 4.4 9.45 2.97 4.55 9.7 3.13 4.71 10.12 3.37 4.92
AP200/11 247.5 72.5 120 254 75.5 123.5 261.5 79.5 127.5 273.5 85.5 133
AP200/15 9.74 2.86 4.72 10 2.97 4.86 10.3 3.13 5.02 10.77 3.37 5.23
257.5 72.5 126 264 75.5 129.5 271.5 79.5 133.5 283.5 85.5 139
AP200/19
10.13 2.86 4.96 10.4 2.97 5.1 10.37 3.13 5.26 11.16 3.37 5.47
AP200/22 262.5 72.5 128.5 269 75.5 131.5 276.5 79.5 135.5 288.5 85.5 141.5
AP200/26 10.3 2.86 5.06 10.6 2.97 5.18 10.89 3.13 5.33 11.36 3.37 5.57
Example of product code
D S
AP300/38 – 200/15 D 2218 AP300/63 – 200/22 S 2218

(Clockwise rotation: D) (Counterclockwise rotation : S)
200 - P - 991218 - E - 00/06.02 92/104

ø19 DIN6888
47 .748" DIA
120 A
4.725" 1.85"
ø 50.8 +0.07 f8
1.999"-1.997" DIA
98 C B 32.5
+0.03
M14x1.5
3.86" 1.28"
F 5
.197"
.927"
23.55
5.04"
1.653"
5.98"
128
2.067"
152
52.5
42
ø 21.59
.85" DIA
.413"
10.5
Taper 1:8
22 80+20 Nm
d 15 118
Max pressure (M max= 65 Nm) .59" 4.64"
bar (PSI)
Pump D 11.2
P1 P2 P3
200 230 250 .44"
AP300/38 (2900) (3300) (3600)
+0.15
.484"-.472"
0
0
190 220 240 4 -0.03 h9
AP300/45
12.15
(2700) (3200) (3400) .157"-.156"
160 190 210
AP300/53 (2300) (2700) (3000)
130 160 180
AP300/63 (1900) (2300) (2600)
100 130 150
AP300/75 (1450) (1900) (2100)
80 110 130
AP300/95 (1150) (1600) (1900)
DisplaĆ Suction Pressure Displacement A B C

cement d D F d D F cm3/rev mm inch mm inch mm inch
cm3/rev mm inch mm inch mm mm inch mm inch mm 53+38 278 10.94 140 5.52
27 53+45 283 11.14 72.5 2.85 142 5.60
31 53+53 288 11.34 144.5 5.69
38 27 1.06 51 2.01 10 20 .79 40 1.58 8 63+27 278 10.95 139.5 5.50
45 63+31 280 11.02 141 5.55
53 63+38 285 11.22 143 5.63
75 5
75.5 2 97
2.97
63 63+45 289 11.38 145.5 5.73
75 32 1.26 62 2.44 12 27 1.65 51 2.01 10 63+53 295 11.61 148 5.83
93 63+63 301 11.85 151 5.95
75+27 285 11.22 143.5 5.65
Displacement A B C
75+31 288 11.34 79.5 3.13 144.5 5.69
cm3/rev mm inch mm inch mm inch
75+38 293 11.54 147 5.79
27+27 254 10.00 63.8 2.51 127.5 5.02
75+45 297 11.70 149.5 5.89
31+27 257 10.12 129 5.08
65 2
65.2 2 57
2.57 75+53 302 11.89 152 5.99
31+31 259 10.20 130.5 5.14 79 5
79.5 3 13
3.13
75+63 309 12.17 155 6.10
38+27 261 10.27 131.5 5.18
75+75 317 12.40 159 6.26
38+31 264 10.40 67.5 2.66 132.5 5.22
93+27 297 11.70 149 5.87
38+38 269 10.60 135 5.32 93+31 300 11.80 150.5 5.93
45+27 266 10.00 133.5 5.26 93+38 304 11.97 153 6.02
45+31 268 10.55 135 5.31 93+45 309 12.17 155 6.10
69 8
69.8 2 75
2.75 85 5
85.5 3 37
3.37
45+38 273 10.75 137.5 5.41 93+53 314 12.36 157.5 6.2
45+45 278 10.95 139.5 5.50 93+63 321 12.64 161 6.34
53+27 271 10.67 136 5.36 93+75 328 12.91 165 6.5
72 5
72.5 2 85
2.85 93+93 340 13.39 170.5 6.72
53+31 274 10.78 137.5 5.42
N.B.: With respect to the standards, the maximum pressures of some versions Note: For the accessories see pump group AP300 code 218 page 87/104.
of this pump are reduced in relation to the max. torque allowed to the shaft.
200 - P - 991218 - E - 00/06.02 93/104

7 Accessories
7.1 Flange connectors
Flange connectors are supplied with bolts and O-ring seals
Material: alluminium alloy C

70 Sh
øD
G
M (Nm)
B C D G
Type Order code A M (Nm) O-Ring
mm inch mm inch mm inch (DIN912)
RF197 200.7702.3001.0 1/2" BSP
RF198 200.7702.1001.0 M18X1.5 30 1.18 16 .63 6.5 .25 10+1 121 M6x1x30
RF199 200.7702.2001.0 3/8" BSP
øC A
Material: cast-iron
70 Sh
E
G
B M (Nm)
D
B C D E M
Type Order code A O-Ring G (DIN912)
mm inch mm inch mm inch mm inch (Nm)
RF223 200.7702.3006.0 1/2" BSP
RF224 200.7702.1007.0 M18X1.5 30 1.18 30 1.18 17.5 .63 6.5 .25 10+1 121 M6x1x18
RF238 200.7702.2004.0 3/8" BSP
RF225 200.7702.4003.0 3/4"BSP
RF246 200.7702.3007.0 1/2"BSP 40 1.57 40 1.57 21 1.02 8.5 .33 20+2 132 M8x1.25x20
RF251 200.7702.1009.0 M18X1.5
RF233 200.7702.5008.0 1"BSP 4118
51 2 48 2 27 .98
98 10 5
10.5 .41
41 30+5 M10x1 5x25
M10x1.5x25
RF261 200.7702.4008.0 3/4"BSP 3125
RF272 200.7702.5004.0 1"BSP 58 2.28 12.5 .51 M12x1.75x30
62 2 44
2.44 34 5
34.5 1 36
1.36 50+2 4150
RF256 200.7702.9007.0 11/4"BSP 60 2.36 10.5 .41 M12x1.75x35
C
Material: alluminium alloy
70 Sh
øD
B C D G
Type Order code A M (Nm) O-Ring
mm inch mm inch mm inch (DIN912)
RF221 200.7702.1006.0 M18x1.5
RF262 200.7702.2007.0 3/8" BSP 35 1.37 18.5 .73 3075
RF216 200.7702.3004.0 1/2" BSP
65
6.5 .25
25 10+1 M6x1x40
RF252 200.7702.1010.0 M18x1.5
RF217 200.7702.3005.0 1/2" BSP 40 1.57 21.5 .85 132
RF220 200.7702.4002.0 3/4" BSP
200 - P - 991218 - E - 00/06.02 94/104
F E
Material: cast-iron G
M (Nm)
B
A
ø10 DIN 128A
RFS250 ø13 UNI1751
C
70 Sh
B C D E F M O-
O
Type Order code A G (DIN912)
mm inch mm inch mm inch mm inch mm inch (Nm) Ring
RFS249 200.7702.4006.0 3/4" BSP 22.2 .87 47.6 1.87 48 1.89 65 2.56 36 1.42 4100 3/8"16UNF
RFS248 200.7702.5003.0 1" BSP 26.2 1.03 52.4 2.06 52 2.04 70 2.75 38 1.50 25+2 4131 3/8"16UNC
RFS275 200.7702.9017.0 11/4" BSP 30.2 1.19 58.7 2.31 68 2.68 79 3.11 41 1.61 4150 7/16"14UNC
RFS250 200.7702.9006.0 11/2" BSP 35.7 1.40 70 2.99 76 2.99 93 3.66 44 1.73 50+2 4187 1/2"13UNC
7.2 Splined couplings

Material: UNI5331 16 CrNi4Pb Hardness 58 - 60 HRc (*) UNI5332 38NiCrMo4Pb R= 950 - 1050 N/mm2
C D
øA
øB
Pump Spline profile A B C D n.

Type Order code
group DIN 5482 mm inch mm inch mm inch mm inch of feet
GSH–06 AP05 200.5314.20001 20X17 7 .27 19.5 .76 9 .35 2 .08 12
C D
øA
øB
1:8

Type Order code
GSH–1–12 AP100 200.5315.30001 20X17 19.5 .77 12
8 .31
31 14 5
14.5 .57
57 24
2.4 .09
09
GSH–1–14 AP100 200.5315.30002 25x22
24 5
24.5 .96
96 14
GSH–2–14* AP200 200.5315.40001 25x22
GSH–2–15 AP200 200.5315.40002 28x25 14.2 .56 27.5 1.08 22 .87 3.2 .12 15
GSH–2–18 AP200 200.5315.40003 35x31
34 5
34.5 1 36
1.36 18
GSH–3–18* AP300 200.5315.50001 35x31
18 7
18.7 .73
73 26 1 02
1.02 4 .16
16
GSH–3–20 AP300 200.5315.50002 40x36 39.5 1.55 20
C D
øA
øB
1:5

Type Order code
GSH–1B–12 AP100 200.5314.30001 20X17 7.6 .3 19.5 .77 12 .47 2 .08 12
GSH–2B–14* AP200 200.5314.40001 25x22 24.5 .96 14
GSH–2B–15 AP200 200.5314.40002 28x25 13 .5 27.5 1.08 20 .79 3 .12 15
GSH–2B–18 AP200 200.5314.40003 35x31 34.5 1.36 18
200 - P - 991218 - E - 00/06.02 95/104
7.3 Independent supports
TC10 (AP100/218 – AP100/318 – AP100/818)

Fr (N)
Lh = 1000 h
2800 a
2500
2300
2100
Fr
1900
1700
1500
1300
1100
900
With Fr and Fa the max radial load is:
Fr max= Fr – (0.7 Fa)
20 30 40 50 60 70 80 a (mm)
42 Code TC10K8
1.65"
6
ø6.5 DIN 6888 .24"
12
.25" DIA
.47"
52.4
23
2.06"
.9"
Taper 1:8
ø 25.4
19 60+10 Nm
1"
1.50"
38
3.66"
2.83"
71.9
93
1.03"
26.2
ø 50.8 -0.06 f7
1.998"-1.997"
-0.03
4
.157"
M12x1.5
.37"
9.5
7
ø17.5 56
.27"
75 2.20"
Taper 1:8
2.95" .69" DIA
Order Code 200.6350.1014.0
Code TC10K0
42
6x25 DIN6885 1.65"
6
.24"x1"
.24"
52.4 35
2.06" 1.38" Taper 1:8
M6x1
ø 25.4
1"
1.50"
38
3.66"
2.83"
71.9
93
1.03"
26.2
6 h7
ø 50.8 -0.06 f7
1.998"-1.997"
.236"-.235"
-0.03
20.5
.81"
19 40
7
.75" 1.57"
.27"
75 18 h7
2.95" .708" - .707"
Order Code 200.6350.1013.0
200 - P - 991218 - E - 00/06.02 96/104

TC35 (AP200/218 – AP200/818) TC40 (AP300/218)
Fr (N) Lh = 1000 h Fr (N) Lh = 1000 h
4500 3000
a
4000 2800
3500 2600
3000 2400 Fr
2500 2200
2000 2000
1500 1800
1000 1600
500 1400
10 20 30 40 50 60 70 a (mm) 20 30 40 50 60 70 80 a (mm)
Code TC35K1 Code TC35K4

ø16 200.6612.0003.0 6x40 DIN6885
.63" DIA .23"x1.57"
1.998"-1.997"
12 27 54.5 53.5
71.5 1.06" 2.14" 2.1"
ø 50.8 f8
.47"
2.81"
Taper 1:8 46.5
M8
1.83"
19 60+10 Nm
1.28"
4.5" 32.5
3.78"
114
96
1.436"-1.434"DIA
1.44" DIA
ø 36.5
M12x1.5
6 h8
ø 36.5f8
.236"-.235"
.968"-.960"
3.2 h8 5 20
89.5 .126"-.125" .19" .78"
11
24.5
3.52" 48.5 5
.37"
ø16.65
9.4
.65" DIA .43" 1.9" .19"

Taper 1:8 22 h7
.866"-.865"
Order code 200.7370.1004.0 Order code 200.7370.1008.0
Code TC40K1 Code TC40K2
ø19 DIN6888 8x30 DIN6885

.75" DIA .31"x1.18"
1.998"-1.997"
14.5 32.5 60 50
98
1.28" 2.36" 1.96"
ø 50.8 f8
M8x1.25
3.86" .57"
Taper 1:8 42.5
22 1.67"
80+20 Nm
1.65"
42
5.04"
6.10"
155
128
1.998"-1.997"DIA
2" DIA
ø 50.8
8 h7
M14x1.5
ø 50.8f8
.314"-.315"
1.15"
29.2
4 h9 5 15
125 .157" .19" .59"
ø21.59 45 5
.48"
4.92" 11
.85" DIA 26 h7
12.15
.43" 1.77" .19"

Taper 1:8
1.023"-1.024"
Order code 200.7380.1001.0 Order code 200.7380.1002.0
200 - P - 991218 - E - 00/06.02 97/104

7.4 Pumps seal kit NBR standard type
AP05 AP200/225 200.9740.0006.0
Pump code Seal kit AP200/227 200.9740.0006.0
AP05/810 200.9740.0018.0 AP200/235 200.9740.0006.0
AP05/819 200.9740.0018.0 AP200/245 200.9740.0006.0
AP05/310 200.9740.0018.0 AP200/237 200.9740.0100.0
AP05/319 200.9740.0018.0 AP200/247 200.9740.0113.0
AP05/410 200.9740.0028.0 AP200/259 200.9740.0008.0
AP05/419 200.9740.0028.0 AP200/225KM5 200.9740.0114.0
AP05/830 200.9740.0018.0 AP200/887S 200.9740.0006.0
AP05/839 200.9740.0018.0 AP200/880 200.9740.0006.0
AP05/330 200.9740.0018.0 AP200/887S NPTF 200.9740.0115.0
AP05/339 200.9740.0018.0 AP200/880 NPTF 200.9740.0115.0
AP05/430 200.9740.0028.0 AP200/287S-B 200.9740.0006.0
AP05/439 200.9740.0028.0 AP200/280B 200.9740.0006.0
APR05/810 200.9740.0026.0
AP200 AP200
Pump code Seal kit
AP100
AP200/2218 200.9740.0007.0
Pump code Seal kit
AP200/8818 200.9740.0116.0
AP100/218 200.9740.0031.0
AP200/2225 200.9740.0007.0
AP100/219 200.9740.0031.0
AP200/2227 200.9740.0007.0
AP100/318 200.9740.0031.0
AP200/2235 200.9740.0007.0
AP100/319 200.9740.0031.0
AP200/2245 200.9740.0007.0
AP100/818 200.9740.0031.0
AP200/2259 200.9740.0007.0
AP100/845 200.9740.0031.0
AP200/8887S 200.9740.0007.0
AP100/849 200.9740.0032.0
AP200/8880 200.9740.0007.0
AP100/849P 200.9740.0033.0
AP200/2287S-B 200.9740.0007.0
AP100/449P 200.9740.0095.0
AP200/2280-B 200.9740.0007.0
AP100/8S49P 200.9740.0096.0
AP200/501 200.9740.0117.0
AP100/880 200.9740.0034.0
AP200/901 200.9740.0118.0
AP100/887S 200.9740.0034.0
AP200/511 200.9740.0119.0
AP100/380 200.9740.0034.0
AP100/387S 200.9740.0034.0
AP300
AP100/887S NPTF 200.9740.0097.0
Pump code Seal kit
AP100/880 NPTF 200.9740.0097.0
AP300/218 200.9740.0014.0
AP100/2218 200.9740.0098.0
AP300/818 200.9740.0014.0
AP100/518 200.9740.0093.0
AP300/287S 200.9740.0017.0
AP300/280 200.9740.0017.0
AP200
Pump code Seal kit AP300 AP200
AP200/218 200.9740.0006.0 Pump code Seal kit
AP200/818 200.9740.0006.0 AP300/2218 200.9740.0011.0
AP200/219A 200.9740.0006.0
AP200/279 200.9740.0099.0 AP300 AP300
AP200/201K8 200.9740.0075.0 Pump code Seal kit
AP200/201K0 200.9740.0074.0 AP300/2218 200.9740.0015.0
Note: For the types of pumps with ordering code not listed, contact our Sales Department.
200 - P - 991218 - E - 00/06.02 98/104

8 Composition of product code
8.1 Single pumps
Type Rotation Code Examples Order code

AP05/ ** * **** AP05/075 D 819 200.1004.642.02
APR05/ ** **** APR05/05 810 200.1003.611.01
AP100/ ** * **** AP100/4.3 S 218 200.1015.133.02
AP200/ ** * **** AP200/11 D 287 S-B 200.1024.862.04
AP300/ ** * **** AP300/45 S 280 200.1034.803.01
8.2 Single pumps with valves
Type Rotation Code Valve Examples Order code

AP200/ ** * **** **** AP200/15 D 218 18VME 200.1025.132.34
AP200/ ** * **** **** AP200/11 S 227 06VP 200.1024.253.06
AP200/ ** * **** **** AP200/19 S 218 08VRI 200.1026.133.18
8.3 Single pumps with support
Type Rotation Code Support Examples Order code

AP200/ ** * **** **** AP200/8.5 D 201-K8 200.1023.132.01
AP200/ ** * **** **** AP200/15 S 225 KM5 200.1025.223.02
8.4 Double pumps
Type 1st Tipo 2nd

Rotation Code Examples Order code
pump pump
AP200/ ** AP200/ ** **** **** AP200/19-200/11 D 2225 200.1226.222.01
AP300/ ** AP200/ ** **** **** AP300/38-200/8.5 D 2218 200.1323.132.09
AP300/ ** AP300/ ** **** **** AP300/53-300/38 S 2218 200.1335.133.03
200 - P - 991218 - E - 00/06.02 99/104

8.5 Product identification plate
Rotation:
D= Clockwise rotation Manufacturing
S= Counterclockwise rotation year and month Progressive identification no. (opzional)
S 2N/****
200101513302 Bucher Hydraulics S.p.A. order code
AP100/4.3 S 218
Description
MADE IN ITALY
8.6 Single pumps weight
Pump Weight Kg Pump Weight Kg Pump Weight Kg Pump Weight Kg

AP05/0.25 0.45 AP100/1.2 0.90 AP200/4.5 1.93 AP300/27 8.2
AP05/0.5 0.45 AP100/1.7 0.95 AP200/6.5 1.94 AP300/31 8.4
AP05/0.75 0.45 AP100/2.5 1.03 AP200/8.5 1.95 AP300/38 8.6
AP05/0.9 0.48 AP100/3.5 1.07 AP200/11 2.33 AP300/45 8.8
AP05/1.2 0.50 AP100/4.3 1.12 AP200/15 2.34 AP300/53 9.0
AP05/1.6 0.50 AP100/5 1.18 AP200/19 2.65 AP300/63 9.2
AP100/6.5 1.23 AP200/22 2.78 AP300/75 9.4
AP100/8 1.28 AP200/26 2.82 AP300/93 9.6
N.B.: The weight refers to pumps with version code 810 (AP05) ć 218 (AP100 ć AP200 ć AP300). Limited weight variations are possible for pumps having a
different code.
Manufacturing year
Manufacturing month
1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007
January 6A 7A 8M 9M 0M 1M 2M 3M 4M 5M 6M 7M
February 6B 7B 8N 9N 0N 1N 2N 3N 4N 5N 6N 7N
March 6C 7C 8P 9P 0P 1P 2P 3P 4P 5P 6P 7P
April 6D 7D 8Q 9Q 0Q 1Q 2Q 3Q 4Q 5Q 6Q 7Q
May 6E 7E 8R 9R 0R 1R 2R 3R 4R 5R 6R 7R
June 6F 7F 8S 9S 0S 1S 2S 3S 4S 5S 6S 7S
July 6G 7G 8T 9T 0T 1T 2T 3T 4T 5T 6T 7T
August 6H 7H 8U 9U 0U 1U 2U 3U 4U 5U 6U 7U
September 6I 7I 8V 9V 0V 1V 2V 3V 4V 5V 6V 7V
October 6J 7J 8Z 9Z 0Z 1Z 2Z 3Z 4Z 5Z 6Z 7Z
November 6K 7K 8X 9X 0X 1X 2X 3X 4X 5X 6X 7X
December 6L 7L 8Y 9Y 0Y 1Y 2Y 3Y 4Y 5Y 6Y 7Y
200 - P - 991218 - E - 00/06.02 100/104

200 - P - 991218 - E - 00/06.02 101/104
200 - P - 991218 - E - 00/06.02 102/104
Bucher Hydraulics pursues a policy of continuos research and development, therefore the company reserves the right to
modify all those technical features which need changing, whenever necessary and without prior notice.
200 - P - 991218 - E - 00/06.02 103/104

02/2001 Id.Nr. 200.599.991208
BUCHER HYDRAULICS www.bucherhydraulics.com

Germany France Netherlands UK USA
Phone +49 7742 85 20 Phone +33 389 64 22 44 Phone +31 79 34 26 24 4 Phone +44 24 76 35 35 61 Phone +1 262 605 82 80
Fax +49 7742 71 16 Fax +33 389 65 28 78 Fax +31 79 34 26 28 8 Fax +44 24 76 35 35 72 Fax +1 262 605 82 78
info.de@bucherhydraulics.com info.fr@.bucherhydraulics.com info.nl@bucherhydraulics.com info.uk@bucherhydraulics.com info.wi@bucherhydraulics.com
Switzerland Italy Austria China Product Center (Elevator)

Phone +41 33 67 26 11 1 Phone +39 0522 92 84 11 Phone +43 6216 44 97 Phone +86 10 64 44 32 38 Phone +41 41 757 03 33
Fax +41 33 67 26 10 3 Fax +39 0522 51 32 11 Fax +43 6216 44 97 4 Fax +86 10 64 44 32 35 Fax +41 41 755 16 49
info.ch@bucherhydraulics.com info.it@bucherhydraulics.com info.at@bucherhydraulics.com info.bj@bucherhydraulics.com info.nh@bucherhydraulics.com
We reserve the right of modification without prior notice.
200 - P - 991218 - E - 00/06.02 104/104

Hydroirma Catalog Gear Pump

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hydroirma Catalog Gear Pump

Uploaded by

Copyright:

Available Formats

Gear Pumps

motion and progress

200 - P - 991218 - E - 00/06.02 1 / 104

Oil retaining ring

Mounting tie rods Driven gear

200 - P - 991218 - E - 00/06.02 2/104

1.1 Introduction to the product

1 - Drive gear 6 - Rear cover

200 - P - 991218 - E - 00/06.02 3/104

Check nut O-Ring

S Left-hand rotation S Pressure flow

200 - P - 991218 - E - 00/06.02 4/104

Temperature * Caution! – Use of pumps at temperatures above 80°C must always be

In certain cases, the suction pressure can exceed 1 bar

2.4 Filtration > 170 bar < 170 bar

200 - P - 991218 - E - 00/06.02 5/104

200 - P - 991218 - E - 00/06.02 6/104

2.7 pressure p (bar)

p0.05 s max. 15 s t (s)

pressure flow rate surging

200 - P - 991218 - E - 00/06.02 7/104

Vc n p Qp N 6.12 ηt N 6120 ηt

2.5 1500 ηt = 0.94 0.87 = 0.82 = 82%

3.52 200 1.4

AP05 Displacement Max. pressure n min. n max.

200 - P - 991218 - E - 00/06.02 8/104

AP200 Displacement Max. pressure n min. n max.

AP300 Displacement Max. pressure n min. n max.

200 - P - 991218 - E - 00/06.02 9/104

Oil viscosity: 37 mm2/s

0 1000 2000 3000 n (min-1 ) 0 1000 2000 3000 n (min-1 )

200 - P - 991218 - E - 00/06.02 10/104

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

n= 2000 (min-1) 1.6 n= 3000 (min-1) 1.6

1.2 0.9 1.2 0.9

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

n= 5000 (min-1) 1.6 n= 7000 (min-1) 1.6

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

200 - P - 991218 - E - 00/06.02 11/104

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

n= 4000 (min-1) n= 5000 (min-1)

8.0 4.3 4.0

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

200 - P - 991218 - E - 00/06.02 12/104

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

200 - P - 991218 - E - 00/06.02 13/104

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

n= 2500 (min-1) n= 3000 (min-1)

0 50 100 150 200 p (bar) 0 50 100 150 200 p (bar)

200 - P - 991218 - E - 00/06.02 14/104

Ambient noise: 38 dB(A)

AP100 P=10 bar h

200 - P - 991218 - E - 00/06.02 15/104

AP05 Displacement Max. pressure n min. n max.

Max torque allowed to the shaft

200 - P - 991218 - E - 00/06.02 16/104

1/4" BSPP Depth.11 -.43" ø7 DIN6888

Clockwise C.clockwise Flange Splined

200 - P - 991218 - E - 00/06.02 17/104

M max= 25 Nm 9 M max= 30 Nm 9

1:5 M max= 40 Nm 5 1:8 M max= 33 Nm 8