Series: General Description

XC6227 Series ETR0354-005
700mA High Speed LDO Regulator with Reverse Current Protection
■GENERAL DESCRIPTION
The XC6227 series is a highly accurate, low noise, high ripple rejection, low dropout, and low power consumption high speed
voltage regulator.
The series consists of a voltage reference, an error amplifier, a driver transistor, a current limiter, a thermal protection circuit, a
reverse current protection circuit and a phase compensation circuit.
The CE function enables the entire circuit to be placed in a stand-by state by inputting a low level signal to the CE pin. Over-current
protection and thermal protection circuits are integrated. The protection circuit starts to operate when either output current reaches
the current limit level or junction temperature reaches the temperature limit. With the reverse current protection function of a driver
transistor, the reverse current flow is prohibited when V OUT voltage is higher than VIN voltage. For an example, when a battery is
connected to the VOUT pin, battery current will not flow back to the XC6227.
■APPLICATIONS ■FEATURES
● USB products and HDMI equipments Maximum Output Current : 700mA
● E-book Readers / Electronic dictionaries Dropout Voltage : 120mV @IOUT=300mA(VOUT=3.0V)
● Smart Phones / Mobile phones Operating Voltage Range : 1.7V ~ 6.0V
Output Voltages : 0.8V ~ 5.0V (0.05V increments)
● Portable game consoles
Accuracy : +1% (VOUT＞2.0V)
● Modules (Wireless, Camera, etc.)
+0.02V (VOUT≦2.0V)
Low Power Consumption : 100μA
Chip Enable(CE) : Active High
Standby Current below 0.1μA
High Ripple Rejection : 65dB @ 1kHz
Operating Ambient Temperature : -40℃ ~ 85℃
Low ESR Capacitor : Ceramic capacitor
Packages : USP-6C, SOT-25, SOT-89-5
Environmentally Friendly : EU RoHS Compliant, Pb Free
■TYPICAL APPLICATION CIRCUIT ■ TYPICAL PERFORMANCE

CHARACTERISTICS
●VOUT Sink
●逆流時V OUT端子シンク電流-入力電圧特性例
Current VS. Input Voltage
USB 5V
XC6227C331
VIN VOUT=3.3V
IOUT=0mA
10
VOUT Sink Current -40℃
VOUT Sink Current：IREVS(μ A)
（TYP：2.8μA） IOUT 8 25℃

CE
XC6227C VOUT 85℃
CIN：1μF(ceramic) To System LSI 6
CL：2.2μF(ceramic)
4
Step-Up
VIN DC/DC VOUT
Converter 2
VSS VSS
Battery 0
-2
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
Input Voltage：VIN(V)
1/23
XC6227 Series
■BLOCK DIAGRAM
1) XC6227 series A type 2) XC6227series C type
Reverse Reverse
Current Current
Protection Protection
VIN VOUT VIN VOUT
CFB CFB
CurrentLimit CurrentLimit
& &
ThermalShutdown R1 R1
ThermalShutdown
+ +
Error Error
Amp Amp
- -
each R2 each R2
circuit Voltage circuit Voltage
ON/OFF ON/OFF
CE Reference CE Reference
Control Control
VSS VSS
XC6227Aseries XC6227Cseries
* Diodes inside the circuits are ESD protection diodes and parasitic diodes.
■PRODUCT CLASSIFICATION
●Ordering Information
XC6227①②③④⑤⑥-⑦(*1)
DESIGNATOR ITEM SYMBOL DESCRIPTION
A
① Type Refer to Selection Guide
C
②③ Output Voltage 08 ~ 50 e.g. 2.8V → ②=2, ③=8
Output voltage {x.x0v} (the 2nd decimal place is "0")

1
Output Voltage ±1% (VOUT>2.0V), ±20mV (VOUT≦2.0V)
④
(the 2nd decimal place) Output voltage {x.x5v} (the 2nd decimal place is "5")
B
±1% (VOUT(T)>2.0V), ±20mV (VOUT(T)≦2.0V)
MR-G SOT-25 (3,000pcs/Reel)
⑤⑥-⑦ Packages (Order Unit) PR-G SOT-89-5 (1,000pcs/Reel)
ER-G USP-6C (3,000pcs/Reel)
(*1)
The “-G” suffix denotes Halogen and Antimony free as well as being fully EU RoHS compliant.
●Selection Guide
CE PULL-DOWN
TYPE CE High Active
RESISTOR
A Yes No
C Yes Yes
2/23
XC6227
Series
■PIN CONFIGURATION
VOUT VIN
5 2 4
VOUT NC
5 4
CE 6 1 VIN
VSS 5 2 NC
NC 4 3 VOUT
1 2 3 1 2 3
VIN VSS CE CE VSS NC
USP-6C SOT-25 SOT-89-5

(BOTTOM VIEW) (TOP VIEW) (TOP VIEW)
*The dissipation pad for the USP-6C package should be solder-plated in recommended mount pattern and metal masking so as to enhance
mounting strength and heat release. If the pad needs to be connected to other pins, it should be connected to the VSS (No. 5) pin.
PIN NUMBER
PIN NAME FUNCTIONS
USP-6C SOT-25 SOT-89-5
1 1 4 VIN Power Input
3 5 5 VOUT Output
2,4 4 3 NC No connection
5 2 2 VSS Ground
6 3 1 CE ON/OFF Control
■FUNCTION CHART
PIN NAME SIGNAL TYPE STATUS
L A,C Stand-by
H A,C Active
CE
A Undefined state
OPEN
C Stand-by
3/23
XC6227 Series
■ABSOLUTE MAXIMUM RATINGS

PARAMETER SYMBOL RATINGS UNITS
Input Voltage VIN VSS - 0.3 ~ 6.5 V
Output Voltage VOUT VSS - 0.3 ~ 6.5 V
CE Input Voltage VCE VSS - 0.3 ~ 6.5 V
120
USP-6C 1000 (40mm x 40mm Standard Board) (*1)
1250(JESD51-7 Board) (*1)
Power 250
Dissipation SOT-25 Pd 600 (40mm x 40mm Standard Board) (*1) mW
(Ta=25℃) 760 (JESD51-7 Board) (*1)
500
SOT-89-5 1300 (40mm x 40mm Standard Board) (*1)
1750 (JESD51-7 Board) (*1)
Operating Ambient Temperature Topr -40 ~ 85 ℃
Storage Temperature Tstg -55 ~ 125 ℃
(*1)
The power dissipation figure shown is PCB mounted and is for reference only.
The mounting condition is please refer to PACKAGING INFORMATION.
4/23
XC6227
Series
■ELECTRICAL CHARACTERISTICS
●XC6227 Series Ta=25℃
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNITS CIRCUIT
VOUT(T)＞2.0V, VCE=VIN, IOUT=10mA ×0.99(*3) VOUT(T) ×1.01 (*3)
Output Voltage VOUT(E) (*2) V ①
VOUT(T)≦2.0V, VCE=VIN, IOUT=10mA -0.02 (*3) (*4)
+0.02 (*3)
VCE=VIN, VIN=VOUT(T)+1.0V
VOUT(T)＞1.5V
Output Current IOUTMAX 700 - - mA ①
VCE=VIN, VIN=2.5V
VOUT(T)≦1.5V
Load Regulation ΔVOUT VCE=VIN, 0.1mA≦IOUT≦300mA E-1 mV ①
Dropout Voltage1 (*5) Vdif IOUT=300mA, VCE=VIN E-2 mV ①
Dropout Voltage2 (*5) Vdif2 IOUT=0mA, VCE=VIN E-3 mV ①
Supply Current ISS VIN=VCE=VOUT(T)+1.0V, IOUT=0mA - 100 220 μA ②
Stand-by Current ISTBY VIN=6.0V, VCE=VSS - 0.01 0.1 μA ②
VOUT(T)+0.5V≦VIN≦6.0V
:VOUT(T)≧1.0V
ΔVOUT/ VCE=VIN, IOUT=30mA
Line Regulation - 0.01 0.1 %/V ①
(ΔVIN ・VOUT) 1.5V≦VIN≦6.0V
:VOUT(T)≦0.95V
VCE=VIN, IOUT=30mA
Input Voltage VIN 1.7 - 6.0 V ①
Output Voltage
ΔVOUT/ VCE=VIN, IOUT=30mA ppm
Temperature - ±100 - ①
(ΔTa ・VOUT) -40℃≦Ta≦85℃ /℃
Characteristics
VOUT(T)≧4.8V,
VIN=5.75VDC+0.5Vp-pAC
VCE=VIN, IOUT=30mA, f=1kHz
1.0V≦VOUT(T)＜4.8V
Power Supply
PSRR VIN=｛VOUT(T)+1.0｝VDC+0.5Vp-pAC - 65 - dB ③
Rejection Ratio
VOUT(T)＜1.0V,
VIN=2.0VDC+0.5Vp-pAC
VCE=VIN, VIN=VOUT(T)+1.0V
VOUT(T)＞1.5V
Limit Current Ilim 720 950 - mA ①
VCE=VIN, VIN=2.5V
VOUT(T)≦1.5V
Short Current Ishort VCE=VIN, Short VOUT to VSS level - 55 - mA ①
CE High Level Voltage VCEH 1.2 - 6.0 V ①
CE Low Level Voltage VCEL VSS - 0.3 V ①
CE High Level Current ICEH VCE=VIN=6.0V, XC6227C Series 17.7 24 36.9 μA ①
CE Low Level Current ICEL VCE=VSS -0.1 - 0.1 μA ①
Reverse Current (*8) IREV VIN=0V, VOUT= 6.0V (*10) - 0.01 1.5 μA ①
VOUT Pin Sink Current (*9) IREVS VIN=5.0V, VOUT=6.0V (*10) - 2.8 5.3 μA ①
Thermal Shutdown
TTSD Junction Temperature - 150 - ℃ ①
Detect Temperature
Thermal Shutdown
TTSR Junction Temperature - 125 - ℃ ①
Release Temperature
NOTE:
* 1: Unless otherwise stated, input voltage is VIN=VOUT(T)＋1.0V.
* 2: VOUT(E) is effective output voltage (Refer to the voltage chart E-1 and E-2)
It is defined as output voltages when an amply stabilized VOUT(T)+1.0V is supplied to the VIN pin while maintaining a certain IOUT .
* 3: The relation between VOUT(E) and VOUT(T) is shown in the voltage chart E-1 and E-2.
* 4: VOUT(T) is nominal output voltage
* 5: Vdif (Vdif2)= {VIN1(*7)-VOUT1(*6)}
* 6: VOUT1 equals 98% of the output voltage when amply stabilized VOUT (T)+1.0V are supplied to the VIN pin.
* 7: VIN1 is the input voltage when VOUT1 appears at the VOUT pin while input voltage is gradually decreased.
* 8: Reverse current (IREV) flows from VOUT to VIN.
* 9: VOUT pin sink current (IREVS) flows from VOUT to VSS.
*10: Please note when an external power supply connects to the VOUT pin, please use it with 6.0V or less.
5/23
XC6227 Series
■OUTPUT VOLTAGE CHART
●Voltage Chart 1
NOMINAL
LOAD REGULATION DROPOUT VOLTAGE 1 DROPOUT VOLTAGE 2
OUTPUT OUTPUT VOLTAGE
VOLTAGE E-1 E-1 E-3
VOUT(E) (V) ΔVOUT(mV) Vdif(mV) Vdif2(mV)

VOUT(T) (V)
MIN. MAX. TYP. MAX. TYP. MAX. TYP. MAX.
0.80 0.7800 0.8200 25 50 720 880 230 510
0.85 0.8300 0.8700 25 50 720 880 230 510
0.90 0.8800 0.9200 25 50 720 880 230 510
0.95 0.9300 0.9700 25 50 720 880 230 510
1.00 0.9800 1.0200 25 50 570 740 75 260
1.05 1.0300 1.0700 30 60 570 740 75 260
1.10 1.0800 1.1200 30 60 570 740 75 260
1.15 1.1300 1.1700 30 60 570 740 75 260
1.20 1.1800 1.2200 30 60 420 570 50 135
1.25 1.2300 1.2700 30 60 420 570 40 80
1.30 1.2800 1.3200 30 60 420 570 40 80
1.35 1.3300 1.3700 30 60 420 570 40 80
1.40 1.3800 1.4200 30 60 320 470 40 80
1.45 1.4300 1.4700 30 60 320 470 40 80
1.50 1.4800 1.5200 30 60 280 410 40 80
1.55 1.5300 1.5700 30 60 280 410 40 80
1.60 1.5800 1.6200 30 60 280 410 40 80
1.65 1.6300 1.6700 30 60 280 410 40 80
1.70 1.6800 1.7200 30 60 280 410 40 80
1.75 1.7300 1.7700 30 60 280 410 40 80
1.80 1.7800 1.8200 30 60 220 350 40 80
1.85 1.8300 1.8700 30 60 220 350 40 80
1.90 1.8800 1.9200 30 60 220 350 40 80
1.95 1.9300 1.9700 30 60 220 350 40 80
2.00 1.9800 2.0200 30 60 200 320 40 80
2.05 2.0295 2.0705 35 70 200 320 40 80
2.10 2.0790 2.1210 35 70 200 320 40 80
2.15 2.1285 2.1715 35 70 200 320 40 80
2.20 2.1780 2.2220 35 70 200 320 40 80
2.25 2.2275 2.2725 35 70 200 320 40 80
2.30 2.2770 2.3230 35 70 200 320 40 80
2.35 2.3265 2.3735 35 70 200 320 40 80
2.40 2.3760 2.4240 35 70 200 320 40 80
2.45 2.4255 2.4745 35 70 200 320 40 80
2.50 2.4750 2.5250 35 70 160 260 40 80
2.55 2.5245 2.5755 35 70 160 260 40 80
2.60 2.5740 2.6260 35 70 160 260 40 80
2.65 2.6235 2.6765 35 70 160 260 40 80
2.70 2.6730 2.7270 35 70 160 260 40 80
2.75 2.7225 2.7775 35 70 160 260 40 80
2.80 2.7720 2.8280 35 70 160 260 40 80
2.85 2.8215 2.8785 35 70 160 260 40 80
2.90 2.8710 2.9290 35 70 160 260 40 80
2.95 2.9205 2.9795 35 70 160 260 40 80
3.00 2.9700 3.0300 43 85 120 200 40 80
6/23
XC6227
Series
■OUTPUT VOLTAGE CHART (Continued)

●Voltage Chart 2
NOMINAL
OUTPUT LOAD REGULATION DROPOUT VOLTAGE 1 DROPOUT VOLTAGE 2
OUTPUT VOLTAGE
E-1 E-2 E-3
VOLTAGE
VOUT(E) (V) ΔVOUT(V) Vdif(mV) Vdif2(mV)

VOUT(T) (V)
MIN. MAX. TYP. MAX. TYP. MAX. TYP MAX
3.05 3.0195 3.0805 43 85 120 200 40 80
3.10 3.0690 3.1310 43 85 120 200 40 80
3.15 3.1185 3.1815 43 85 120 200 40 80
3.20 3.1680 3.2320 43 85 120 200 40 80
3.25 3.2175 3.2825 43 85 120 200 40 80
3.30 3.2670 3.3330 43 85 120 200 40 80
3.35 3.3165 3.3835 43 85 120 200 40 80
3.40 3.3660 3.4340 43 85 120 200 40 80
3.45 3.4155 3.4845 43 85 120 200 40 80
3.50 3.4650 3.5350 43 85 120 200 40 80
3.55 3.5145 3.5855 43 85 120 200 40 80
3.60 3.5640 3.6360 43 85 120 200 40 80
3.65 3.6135 3.6865 43 85 120 200 40 80
3.70 3.6630 3.7370 43 85 120 200 40 80
3.75 3.7125 3.7875 43 85 120 200 40 80
3.80 3.7620 3.8380 43 85 120 200 40 80
3.85 3.8115 3.8885 43 85 120 200 40 80
3.90 3.8610 3.9390 43 85 120 200 40 80
3.95 3.9105 3.9895 43 85 120 200 40 80
4.00 3.9600 4.0400 43 85 120 200 40 80
4.05 4.0095 4.0905 50 100 120 200 40 80
4.10 4.0590 4.1410 50 100 120 200 40 80
4.15 4.1085 4.1915 50 100 120 200 40 80
4.20 4.1580 4.2420 50 100 120 200 40 80
4.25 4.2075 4.2925 50 100 120 200 40 80
4.30 4.2570 4.3430 50 100 120 200 40 80
4.35 4.3065 4.3935 50 100 120 200 40 80
4.40 4.3560 4.4440 50 100 120 200 40 80
4.45 4.4055 4.4945 50 100 120 200 40 80
4.50 4.4550 4.5450 50 100 120 200 40 80
4.55 4.5045 4.5955 50 100 120 200 40 80
4.60 4.5540 4.6460 50 100 120 200 40 80
4.65 4.6035 4.6965 50 100 120 200 40 80
4.70 4.6530 4.7470 50 100 120 200 40 80
4.75 4.7025 4.7975 50 100 120 200 40 80
4.80 4.7520 4.8480 50 100 120 200 40 80
4.85 4.8015 4.8985 50 100 120 200 40 80
4.90 4.8510 4.9490 50 100 120 200 40 80
4.95 4.9005 4.9995 50 100 120 200 40 80
5.00 4.9500 5.0500 50 100 120 200 40 80
7/23
XC6227 Series
■TEST CIRCUITS
●測定回路①
Circuit ①
VIN
CIN(ceramic)
V A CE VOUT A
V V
VSS CL
(ceramic)
●測定回路②
Circuit ②
VIN
CIN(ceramic) CE VOUT
V
CL(ceramic)
VSS
●測定回路③
Circuit ③
VIN
IOUT
V CE VOUT A
V
CL ※ CIN：1.0μF or higher
VSS (ceramic)
　 CL：2.2μF or higher (VOUT=2.5～5.0V)
4.7μF or higher (VOUT=2.1～2.45V)
6.8μF or higher (VOUT=0.8～2.05V)
8/23
XC6227
Series
■OPERATIONAL EXPLANATION
The voltage divided by two resistors R1 and R2 is compared with the internal reference voltage by the error amplifier. The P-
channel MOSFET connected to the VOUT pin, is then driven by the subsequent output signal. The output voltage at the VOUT pin
is controlled and stabilized by a system of negative feedback. The current limit and short protection operate in relation to the level
of output current. The thermal protection operates in relation to the level of heat generation. The reverse current protection
operates when VOUT voltage is higher than VIN voltage. Further, the IC's internal circuitry can be turned off via the CE pin's signal.
Reverse
Current
Protection
VIN VOUT
CFB
CurrentLimit
&
ThermalShutdown R1
+
Error
Amp
-
each R2
circuit Voltage
ON/OFF
CE Reference
Control
VSS
XC6227Cseries
<Input and Output Capacitors>

The XC6227 needs an output capacitor CL for phase compensation. Values required for the phase compensation are shown in
the chart below. If a loss of the capacitance happens, stable phase compensation may not be obtained. Please ensure to use a
capacitor which does not depend on bias or temperature too much. For a stable power input, please connect an input capacitor
CIN of 1.0μF between the VIN pin and the VSS pin.
●Output Capacitor (CL) Table
NOMINAL OUTPUT VOLTAGE VOUT(T) OUTPUT CAPACITOR CL
0.8V ~ 2.05V CL=6.8μF
2.1V ~ 2.45V CL=4.7μF
2.5V ~ 5.00V CL=2.2μF
<Reverse Current Protection>

The XC6227 series includes reverse current protection to prevent the damage as a result of current flow from VOUT pin to the
VIN pin and VSS pin when the power supply is connected to the VOUT pin. When VIN is smaller than VOUT, the reverse current
protection works and suppress the reverse current to 1.5μA (MAX.).
When VIN is smaller than VOUT, the VOUT pin sink current flowing from the VOUT pin to the VSS pin is 2.8μA (TYP.) as the IC
operation current.
Please also note when an external power supply is connected to the VOUT pin, please use it within 6.0V.
<Current Limiter, Short-Circuit Protection>

The XC6227 series integrates an output current limiter and a fold-back short protection for the output pin. When the load current
reaches the current limit level, the fixed current limiter circuit operates and output voltage drops. When the output pin is short-
circuited to the VSS pin, the current is decreased to a level of 55mA (TYP.).
<Thermal Shutdown>
When the junction temperature of the built-in driver transistor reaches the temperature limit level (150℃ TYP.), the thermal
shutdown circuit operates and the driver transistor will be turned OFF. The IC resumes its operation when the thermal shutdown
function is released and the IC’s operation is automatically restored because the junction temperature drops to the level of 125℃
(TYP.) as the thermal shutdown release voltage.
<CE Pin>
The entire XC6227 circuitry can be turned off via the CE pin signal. In shutdown mode, output at the VOUT pin will be pulled
down to the VSS level via R1 & R2.
The XC6227C type has a pull-down resistor in order to operate normally even the CE pin is left open (when the CE pin is left
open, the IC stops operation), so that the CE pin input current flows.
If the CE pin voltage is set with the specified voltage range, the logic is fixed and the IC will operate normally. However, the
supply current may increase as a result of shoot-through current in the IC's internal circuitry when a medium voltage is input to
the CE pin.
9/23
XC6227 Series
■NOTES ON USE
1. For temporary, transitional voltage drop or voltage rising phenomenon, the IC is liable to malfunction should the ratings be
exceeded.
2. Where wiring impedance is high, operations may become unstable due to noise and/or phase lag depending on output
current.
Please wire the input capacitor (CIN) and the output capacitor (CL) as close to the IC as possible.
3. Torex places an importance on improving our products and its reliability.

However, by any possibility, we would request user fail-safe design and post-aging treatment on system or equipment.
10/23
XC6227
Series
■TYPICAL
■特性例 PERFORMANCE CHARACTERISTICS
　　(1) 出力電圧-出力電流特性例
(1) Output Voltage vs. Output Current *CE Voltage condition: unless otherwise stated VCE=VIN
XC6227x081 XC6227x081
VIN = 1.8V Ta = 25℃
CIN = 1.0μ F (ceramic),CL=6.8μ F(ceramic) CIN = 1.0μ F (ceramic),CL=6.8μ F(ceramic)
1.0 1.0
Output Voltage: VOUT [V]

0.8 0.8
0.6 0.6
VIN=1.4V
0.4 -40℃ 0.4 VIN=1.6V
VIN=1.8V
25℃
0.2 VIN=2.3V
0.2 VIN=6.0V
85℃
0.0 0.0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200
Output Current: IOUT [mA] Output Current: IOUT [mA]
XC6227x151 XC6227x151
VIN = 2.5V Ta = 25℃
2.0 2.0
1.5 1.5
1.0 1.0
VIN=1.6V
-40℃ VIN=1.8V
VIN=2.0V
0.5 25℃ 0.5 VIN=2.5V
VIN=6.0V
85℃
0.0 0.0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200
XC6227x281 XC6227x281
VIN = 3.8V Ta = 25℃
3.0 3.0
2.5
2.5
2.0 2.0
1.5 1.5
-40℃ VIN=2.9V
1.0 1.0 VIN=3.1V
25℃ VIN=3.3V
VIN=3.8V
0.5 85℃ 0.5 VIN=6.0V
0.0 0.0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200
11/23
XC6227 Series
■TYPICAL
■特性例 PERFORMANCE CHARACTERISTICS (Continued)
　　(1) 出力電圧-出力電流特性例
(1) Output Voltage vs. Output Current (Continued)
XC6227x501 XC6227x501
VIN = 6.0V Ta = 25℃
6.0 6.0
5.0
5.0

4.0 4.0
3.0 3.0
-40℃
2.0 2.0 VIN=5.1V
25℃
VIN=5.3V
1.0 85℃ 1.0 VIN=5.5V
VIN=6.0V
0.0 0.0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200
(2) Output
　　(2) Voltage vs. Input Voltage
出力電圧-入力電圧特性例
XC6227x081 XC6227x081
Ta = 25℃ Ta = 25℃
1.0 0.90
0.8 0.85
0.6 0.80
0.4 IOUT=0.1mA 0.75 IOUT=0.1mA

IOUT=10mA IOUT=10mA
0.2 IOUT=30mA 0.70 IOUT=30mA
IOUT=100mA
IOUT=100mA
0.0 0.65
0.0 1.0 2.0 3.0 4.0 5.0 6.0 2.0 3.0 4.0 5.0 6.0
Input Voltage: VIN [V] Input Voltage: VIN [V]
XC6227x151 XC6227x151
Ta = 25℃ Ta = 25℃
2.0 1.60
1.55
1.5
1.50
1.0
IOUT=0.1mA 1.45
IOUT=0.1mA
IOUT=10mA
IOUT=10mA
0.5 IOUT=30mA
1.40 IOUT=30mA
IOUT=100mA
IOUT=100mA
0.0 1.35
0.0 1.0 2.0 3.0 4.0 5.0 6.0 2.0 3.0 4.0 5.0 6.0
12/23
XC6227
Series
■TYPICAL
　　(2) 出力電圧-入力電圧特性例
(2) Output Voltage vs. Input Voltage (Continued)
XC6227x281 XC6227x281
Ta = 25℃ Ta = 25℃
3.0 3.00
2.5

2.90
2.0
2.80
1.5
IOUT=0.1mA
2.70 IOUT=0.1mA
IOUT=10mA
1.0 IOUT=10mA
IOUT=30mA
IOUT=30mA
0.5 IOUT=100mA 2.60
IOUT=100mA
0.0 2.50
0.0 1.0 2.0 3.0 4.0 5.0 6.0 3.0 3.5 4.0 4.5 5.0 5.5 6.0
XC6227x501 XC6227x501
Ta = 25℃ Ta = 25℃
6.0 5.20
5.0
5.10
4.0
5.00
3.0
IOUT=0.1mA 4.90 IOUT=0.1mA
2.0 IOUT=10mA
IOUT=10mA
1.0
IOUT=30mA 4.80 IOUT=30mA
IOUT=100mA IOUT=100mA
0.0 4.70
0.0 1.0 2.0 3.0 4.0 5.0 6.0 5.2 5.4 5.6 5.8 6.0
(3) Dropout
　　(3) Voltage vs. Output Current
入出力電位差-出力電流特性例
XC6227x081 XC6227x151
1400 1000
-40℃
Dropout Voltage: Vdif [mV]
1200 25℃
※Below the minimum 800
1000 operating voltage 85℃
600
800
600 400
-40℃
400
25℃
200
200 85℃ ※Below the minimum
operating voltage
0 0
0 100 200 300 400 500 600 700 0 100 200 300 400 500 600 700
13/23
XC6227 Series
■TYPICAL
　　(3)
(3) 入出力電位差-出力電流特性例
Dropout Voltage vs. Output Current (Continued)
XC6227x281 XC6227x501
800 500
-40℃ -40℃

25℃ 25℃
400
600 85℃ 85℃
300
400
200
200
100
0 0
0 100 200 300 400 500 600 700 0 100 200 300 400 500 600 700
(4) 消費電流-入力電圧特性例
　　(4) Supply Current vs. Input Voltage
XC6227x081 XC6227x151
200 200
Supply Current: ISS [μ A]
150 150
100 100
-40℃ -40℃
50 50
25℃ 25℃
85℃ 85℃
0 0
0 1 2 3 4 5 6 0 1 2 3 4 5 6
XC6227x281 XC6227x501
200 200
-40℃ -40℃
25℃
25℃
150 85℃ 150
85℃
100 100
50 50
0 0
0 1 2 3 4 5 6 0 1 2 3 4 5 6
14/23
XC6227
Series
■TYPICAL
　　(5) 出力電圧-周辺温度特性例
(5) Output Voltage vs. Ambient Temperature
XC6227x081 XC6227x151
VIN = 1.8V,IOUT=30mA VIN = 2.5V,IOUT=30mA
0.85 1.60

0.83 1.55
0.80 1.50
0.78 1.45
0.75 1.40
-50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100
Ambient Temperature: Ta [℃] Ambient Temperature: Ta [℃]
XC6227x281 XC6227x501
VIN = 3.8V,IOUT=30mA VIN = 6.0V,IOUT=30mA
3.00 5.40
2.90 5.20
2.80 5.00
2.70 4.80
2.60 4.60
-50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100
Ambient Temperature: Ta [℃] Ambient Temperature: Ta [℃]
(6) CE
　　(6) Pin Threshold Voltage vs. Ambient Temperature
CE閾値-周辺温度特性例 (7) Reverse Current vs. Output Voltage
　　(7)逆流電流-出力電圧特性例
XC6227 XC6227
VIN=0V
1.2 5
CE Threshold Voltage: VCE [V]
1.0 0
Reverse Current：IREV(μ A)
0.8 -5
0.6 -10
-40℃
0.4 -15
25℃
CE "H" LEVEL
0.2 CE "L" LEVEL -20 85℃
0.0 -25
-50 -25 0 25 50 75 100 0 1 2 3 4 5 6
Ambient Temperature: Ta [℃] Output Voltage：VOUT(V)
15/23
XC6227 Series
■TYPICAL
　　(8)逆流時V
(8) VOUT SinkOUT端子シンク電流-出力電圧特性例
Current vs. Output Voltage
XC6227
VIN=2.4V
10
-40℃
VOUT Sink Current：IREVS(μ A)
8
25℃
6 85℃
0
2.5 3 3.5 4 4.5 5 5.5 6
Output Voltage：VOUT(V)
(9) 入力立上り特性例
　　(9) Input Transient Response
XC6227x081 XC6227x151
Ta = 25℃, IOUT=30mA Ta = 25℃, IOUT=30mA
VIN = 0→1.8V, tr = 5μ s, CL = 6.8μ F (ceramic) VIN = 0→2.5V, tr = 5μ s, CL = 6.8μ F (ceramic)
3.0 3.0 3.0 3.0
5.1
2.9
5.0
2.8
4.9
2.7
4.8 1000
1000
800
800
600
600 5.1
2.9
5.0
2.8
4.9
2.7 1000
800
6001000
800
600
2.6
4.7
2.5 2400
400
200
00 2.5 4.8
2.6
4.7
2.5 400400
2000
200 2.5
2.0 4.6
2.4 00 2.0 4.6
2.4 0

Input Voltage: VIN [V]
Input Voltage
1.0 Input Voltage 2.0 1.0 2.0

Output Voltage
0.0 1.5 0.0 1.5
-1.0 Output Voltage 1.0 -1.0 1.0
-2.0 0.5 -2.0 0.5
-3.0 0.0 -3.0 0.0
Time [40μ s/div] Time [40μ s/div]
XC6227x281 XC6227x501
VIN = 0→3.8V,tr = 5μ s, CL = 2.2μ F (ceramic) VIN = 0→6.0V, tr = 5μ s, CL = 2.2μ F (ceramic)
6.0 6.0 8.0 12.0

5.1
2.9 1000 5.1
2.9 1000
1000
4.0 5.0
2.8
4.9
2.7
4.8
2.6
4.7
2.5 800
600
400
200 5.0 6.0 5.0
2.8
4.9
2.7
4.8
2.6
4.7
2.5 800
600
400800
200600
200 10.0
400
4.6
2.4 0 4.6
2.4 0 0
Input Voltage Input Voltage

2.0 Output Voltage 4.0 4.0 8.0
Output Voltage
0.0 3.0 2.0 6.0
-2.0 2.0 0.0 4.0
-4.0 1.0 -2.0 2.0

-6.0 0.0 -4.0 0.0
16/23
XC6227
Series
■TYPICAL
　　(10) CE立上り特性例
(10) CE Rising Response Time
XC6227x081 XC6227x151
Ta = 25℃, VIN=1.8V, IOUT=30mA, VCE = 0→1.8V, tr = 5μ s Ta = 25℃, VIN=2.5V, IOUT=30mA, VCE = 0→2.5V, tr = 5μ s
CIN = 1.0μ F (ceramic),CL=6.8μ F(ceramic) CIN =1.0μ F (ceramic),CL=6.8μ F (ceramic)
3.0 3.0 3.0 3.0

2.0 2.5

2.0 2.5
CE Input Voltage
CE Voltage: VCE [V]
CE Voltage: VCE [V]

1.0 CE Input Voltage 2.0 1.0 2.0
Output Voltage
0.0 1.5 0.0 1.5
-1.0 Output Voltage 1.0 -1.0 1.0
-2.0 0.5
-2.0 0.5
-3.0 0.0
-3.0 0.0
Time [40μ s/div]
Time [40μ s/div]
XC6227x281 XC6227x501
Ta = 25℃, VIN=3.8V, IOUT=30mA, VCE = 0→3.8V, tr = 5μ s Ta = 25℃, VIN=6.0V, IOUT=30mA, VCE = 0→5.0V, tr = 5μ s
CIN =1.0μ F (ceramic),CL=2.2μ F (ceramic) CIN= 1.0μ F (ceramic),CL=2.2μ F (ceramic)
6.0 6.0 8.0 12.0

4.0 5.0 6.0 10.0

CE Voltage: VCE [V]
CE Voltage: VCE [V]
CE Input Voltage CE Input Voltage

2.0 4.0 4.0 8.0
Output Voltage Output Voltage
0.0 3.0 2.0 6.0
-2.0 2.0 0.0 4.0
-4.0 1.0 -2.0 2.0
-6.0 0.0 -4.0 0.0

　　(11)入力過渡応答特性例
(11) Input Transient Response
XC6227x081 XC6227x151
VIN = 1.8V⇔2.8V, tr = tf = 5μ s, CL = 6.8μ F (ceramic) VIN = 3.8V⇔4.8V, tr = tf = 5μ s, CL = 6.8μ F (ceramic)
3.8 0.84 4.5 1.54
5.1
2.9
5.0
2.8
4.9
2.7
4.8
2.6 1000
1000
800
800
600
600
400
400
4.7
2.5
4.6
2.4 2
2
0
0 00
00
2.8 0.83 3.5 1.53

Input Voltage
1.8 Input Voltage 0.82 2.5 1.52
0.8 0.81 1.5 1.51
-0.2 0.80 0.5 1.50
-1.2 Output Voltage 0.79 -0.5 Output Voltage 1.49

-2.2 0.78 -1.5 1.48
17/23
XC6227 Series
■TYPICAL
　　(11)入力過渡応答特性例
(11) Input Transient Response (Continued)
XC6227x281 XC6227x501
VIN = 5.5V⇔6.0V, tr = tf = 5μ s, CL = 2.2μ F (ceramic) VIN = 5.5V⇔6.0V, tr = tf = 5μ s, CL = 2.2μ F (ceramic)
5.8 2.84 6.5 5.04

4.8 2.83 6.0 5.03

Input Voltage Input Voltage
3.8 2.82 5.5 5.02
2.8 2.81 5.0 5.01
1.8 2.80 4.5 5.00
0.8 Output Voltage 2.79 4.0 Output Voltage 4.99
-0.2 2.78 3.5 4.98

　　(12) 負荷過渡応答特性例
(12) Load Transient Response
XC6227x081 XC6227x081
VIN=1.8V , Ta = 25℃ , IOUT = 10⇔100mA , tr=tf=5μ s VIN=1.8V , Ta = 25℃ , IOUT = 10⇔300mA , tr=tf=5μ s
CIN =1.0μ F (ceramic) , CL=6.8μ F(cceramic) CIN = 1.0μ F (ceramic) , CL=6.8μ F(ceramic)
0.85 1000 0.85 1000
Output Current Iout[mA]

0.80 800 0.80 800

0.75 600 0.75 600
0.70 400 0.70 Output Current 400
0.65 Output Current 200 0.65 200
0.60 0 0.60 0
XC6227x151 XC6227x151
CIN = 1.0μ F (ceramic) , CL=6.8μ F(ceramic) CIN = 1.0μ F (ceramic) , CL=6.8μ F(ceramic)
1.55 1000 1.55 1000
1.50 800 1.50 800
Output Voltage 1.45 Output Voltage 600

1.45 600
1.30 0 1.30 0
18/23
XC6227
Series
■TYPICAL
　　(12) 負荷過渡応答特性例
(12) Load Transient Response (Continued)
XC6227x281 XC6227x281
2.90 1000 2.90 1000


2.80 800 2.80 800
2.70 600 2.70 600
2.40 0 2.40 0
XC6227x501 XC6227x501
5.10 1000 5.10 1000

5.00 800 5.00 800
Output Voltage 4.90 Output Voltage 600

4.90 600
4.60 0 4.60 0
(13) Ripple Rejection Rate

　　(13) リップル除去率特性例
XC6227x081 XC6227x151
VIN = 1.8VDC+0.5Vp-pAC, C L = 6.8μ F (ceramic) VIN = 2.5VDC+0.5Vp-pAC, C L = 6.8μ F (ceramic)
80 80
Ripple Rejection Rate: RR [dB]
60 60
40 40
20 20
0 0
10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M
Ripple Frequency: f [Hz] Ripple Frequency: f [Hz]
19/23
XC6227 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
■特性例
(13) Ripple
　　(13) Rejection Rate (Continued)
リップル除去率特性例
XC6227x281 XC6227x501
VIN = 3.8VDC+0.5Vp-pAC, C L = 2.2μ F (ceramic) VIN = 5.75VDC+0.5Vp-pAC, C L = 2.2μ F (ceramic)
80 80

60 60
40 40
20 20
0 0
10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M
Ripple Frequency: f [Hz] Ripple Frequency: f [Hz]
(14) Output Noise Density
XC6227x121 XC6227x181
VIN=2.2V, Ta=25℃ VIN=2.8, Ta=25℃
CIN=1.0μ F(ceramic), CL=6.8μ F(ceramic) CIN=1.0μ F(ceramic), CL=6.8μ F(ceramic)
100 100
Output Noise Density : [μ V/√Hz]
Frequency-Range ： 0.1～100kHz Frequency-Range ： 0.1～100kHz

Output Noise ： 51.53μ Vrms Output Noise ： 76.29μ Vrms
10 10
IOUT=30mA IOUT=30mA
1 1
0.1 0.1
0.01 0.01
0.1 1 10 100 0.1 1 10 100
Frequency : f [kHz] Frequency : f [kHz]
XC6227x331
VIN=5.0V, Ta=25℃
CIN=1.0μ F(ceramic), CL=2.2μ F(ceramic)
100
Frequency-Range ： 0.1～100kHz
Output Noise ： 143.28μ Vrms
10
IOUT=30mA
0.1
0.01
0.1 1 10 100
Frequency : f [kHz]
20/23
XC6227
Series
■PACKAGING INFORMATION
For the latest package information go to, www.torexsemi.com/technical-support/packages
PACKAGE OUTLINE / LAND PATTERN THERMAL CHARACTERISTICS
Standard Board
SOT-25 SOT-25 PKG SOT-25 Power Dissipation
JESD51-7 Board
Standard Board
SOT-89-5 SOT-89-5 PKG SOT-89-5 Power Dissipation
JESD51-7 Board
Standard Board
USP-6C USP-6C PKG USP-6C Power Dissipation
JESD51-7 Board
21/23
E 015 XC6227S015**-G Z 030 XC6227S030**-G
マーク④,⑤ 製造ロットを表す。01～09、0A～0Z、11･･･9Z、A1～A9、AA･･･Z9、ZA～ZZを繰り返す。
(但し、G，I，J，O，Q，Wは除く。反転文字は使用しない。)
XC6227 Series
■MARKING
※SOT-25は、UnderRULE
dot仕様とする。
　システム管理上、オーダーシート・CSVデータ内の対象マーク前に「#」を付けて表す。
●SOT-25 / SOT-89-5 / USP-6C
●SOT-25
SOT-25(Under dot仕様) ●SOT-89-5
SOT-89-5 ●USP-6C
USP-6C
5 4
5 2 4 1 6
①
④
②
① ② ③ ④ ⑤ 2
5
③
③
⑤
3 4
④
1 2 3
②
①
Enlarge
拡大
1 2 3
* SOT-25 Under dot
① represents product series
MARK PRODUCT SERIES

3 XC6227******-G
② represents regulator type, voltage range, and accuracy

OUTPUT
MARK REGULATOR TYPE ACCURACY PRODUCT SERIES
VOLTAGE RANGE
A A 0.8～2.9 1 XC6227A081**-G～XC6227A291**-G
B A 0.85～2.95 B XC6227A08B**-G～XC6227A29B**-G
C A 3.0～5.0 1 XC6227A301**-G～XC6227A501**-G
D A 3.05～4.95 B XC6227A30B**-G～XC6227A49B**-G
E C 0.8～2.9 1 XC6227C081**-G～XC6227C291**-G
F C 0.85～2.95 B XC6227C08B**-G～XC6227C29B**-G
H C 3.0～5.0 1 XC6227C301**-G～XC6227C501**-G
K C 3.05～4.95 B XC6227C30B**-G～XC6227C49B**-G
* Accuracy “1”- 0.1V step, Accuracy “B”- 0.05V step
③ represents output voltage.

OUTPUT OUTPUT OUTPUT
MARK MARK MARK
VOLTAGE (V) VOLTAGE (V) VOLTAGE (V)
0 - 3.0x A 1.0x 4.0x N 2.0x 5.0x
1 - 3.1x B 1.1x 4.1x P 2.1x -
2 - 3.2x C 1.2x 4.2x R 2.2x -
3 - 3.3x D 1.3x 4.3x S 2.3x -
4 - 3.4x E 1.4x 4.4x T 2.4x -
5 - 3.5x F 1.5x 4.5x U 2.5x -
6 - 3.6x H 1.6x 4.6x V 2.6x -
7 - 3.7x K 1.7x 4.7x X 2.7x -
8 0.8x 3.8x L 1.8x 4.8x Y 2.8x -
9 0.9x 3.9x M 1.9x 4.9x Z 2.9x -
④⑤ represents production lot number

01 to 09, 0A to 0Z, 11 to 9Z, A1 to A9, AA to Z9, ZA to ZZ repeated. (G, I, J, O, Q, W excluded)
* No character inversion used.
22/23
XC6227
Series
1. The product and product specifications contained herein are subject to change without notice to
improve performance characteristics. Consult us, or our representatives before use, to confirm
that the information in this datasheet is up to date.
2. The information in this datasheet is intended to illustrate the operation and characteristics of our
products. We neither make warranties or representations with respect to the accuracy or
completeness of the information contained in this datasheet nor grant any license to any
intellectual property rights of ours or any third party concerning with the information in this
datasheet.
3. Applicable export control laws and regulations should be complied and the procedures required
by such laws and regulations should also be followed, when the product or any information
contained in this datasheet is exported.
4. The product is neither intended nor warranted for use in equipment of systems which require
extremely high levels of quality and/or reliability and/or a malfunction or failure which may cause
loss of human life, bodily injury, serious property damage including but not limited to devices or
equipment used in 1) nuclear facilities, 2) aerospace industry, 3) medical facilities, 4) automobile
industry and other transportation industry and 5) safety devices and safety equipment to control
combustions and explosions. Do not use the product for the above use unless agreed by us in
writing in advance.
5. Although we make continuous efforts to improve the quality and reliability of our products;
nevertheless Semiconductors are likely to fail with a certain probability. So in order to prevent
personal injury and/or property damage resulting from such failure, customers are required to
incorporate adequate safety measures in their designs, such as system fail safes, redundancy
and fire prevention features.
6. Our products are not designed to be Radiation-resistant.
7. Please use the product listed in this datasheet within the specified ranges.
8. We assume no responsibility for damage or loss due to abnormal use.
9. All rights reserved. No part of this datasheet may be copied or reproduced unless agreed by Torex
Semiconductor Ltd in writing in advance.
TOREX SEMICONDUCTOR LTD.
23/23

Series: General Description

Uploaded by

Copyright:

Available Formats

Series: General Description

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Series: General Description

Uploaded by

Copyright:

Available Formats

XC6227 Series ETR0354-005

700mA High Speed LDO Regulator with Reverse Current Protection

■TYPICAL APPLICATION CIRCUIT ■ TYPICAL PERFORMANCE

（TYP：2.8μA） IOUT 8 25℃

②③ Output Voltage 08 ~ 50 e.g. 2.8V → ②=2, ③=8

Output voltage {x.x0v} (the 2nd decimal place is "0")

VIN VSS CE CE VSS NC

USP-6C SOT-25 SOT-89-5

PIN NAME SIGNAL TYPE STATUS

■ABSOLUTE MAXIMUM RATINGS

VOUT(E) (V) ΔVOUT(mV) Vdif(mV) Vdif2(mV)

■OUTPUT VOLTAGE CHART (Continued)

VOUT(E) (V) ΔVOUT(V) Vdif(mV) Vdif2(mV)

<Input and Output Capacitors>

<Reverse Current Protection>

<Current Limiter, Short-Circuit Protection>

3. Torex places an importance on improving our products and its reliability.

Output Voltage: VOUT [V]

Output Voltage: VOUT [V]

Output Voltage: VOUT [V]

Output Voltage: VOUT [V]

0.4 IOUT=0.1mA 0.75 IOUT=0.1mA

Output Voltage: VOUT [V]

Output Voltage: VOUT [V]

Dropout Voltage: Vdif [mV]

Supply Current: ISS [μ A]

Supply Current: ISS [μ A]

Output Voltage: VOUT [V]

Output Voltage: VOUT [V]

1.0 Input Voltage 2.0 1.0 2.0

6.0 6.0 8.0 12.0

Input Voltage: VIN [V]

Input Voltage Input Voltage

-2.0 2.0 0.0 4.0

-4.0 1.0 -2.0 2.0

Output Voltage: VOUT [V]

Output Voltage: VOUT [V]

CE Voltage: VCE [V]

6.0 6.0 8.0 12.0

Output Voltage: VOUT [V]

4.0 5.0 6.0 10.0

CE Input Voltage CE Input Voltage

-2.0 2.0 0.0 4.0

-4.0 1.0 -2.0 2.0

-6.0 0.0 -4.0 0.0

Output Voltage: VOUT [V]

2.8 0.83 3.5 1.53

Input Voltage: VIN [V]

0.8 0.81 1.5 1.51

-0.2 0.80 0.5 1.50

-1.2 Output Voltage 0.79 -0.5 Output Voltage 1.49

Output Voltage: VOUT [V]

Output Voltage: VOUT [V]

Input Voltage: VIN [V]

2.8 2.81 5.0 5.01

1.8 2.80 4.5 5.00

0.8 Output Voltage 2.79 4.0 Output Voltage 4.99

-0.2 2.78 3.5 4.98