Transparent canopy

Detailed interior
Rotatable propeller

SOVIET NIGHT FIGHTER

LAVOCHKIN LA-11
NORTH COREAN AIR FORCES - 1953

Computer Synthesysed model / Êîìïüþòåðíàÿ ìîäåëü

The Model

C 2001 E. ZARKOV MADE IN BULGARIA BY REQUEST OF MOSHE LEMER, ISRAEL

 1/32 SCALE La-11

ASSEMBLY INSTRUCTION

The proposed La-11 model is comparatively complicated and with high level of similarity to the
prototype. Thus, a special attention and precision in the assembly procedure is required. Study
carefully the illustrative drawings, cutouts and present instruction before starting the work on the
model. Try to imagine the separate assembly phases and the purpose of each detail.
After the acquaintance with the model, you may start the assemblage. Follow the sequence given in
the instruction. Cut the necessary details shortly before using them in order to avoid possible
mistakes. Score all fold lines before cutting the details. The places of scoring are marked with small
thin lines on the continuation of fold lines outside the parts. The thick line markings show where to
make cuts on some details - cuts on the wing-fuselage joint cowlings and holes for transparent areas.
Do not be in a hurry with gluing - carefully check and shape the details until obtaining the exact and
correct fit. Before starting the work get hold of the necessary tools: scissors, sharp modeling knife,
blunt knife for scoring the fold lines, prickle, ruler, nippers and grinding paper. Additional materials
necessary for the assemblage are: sheet of cardboard with thickness approximately 0.5 mm, a piece
of wire with diameter 0.5 - 0.8 mm, transparent foil for the canopy. Supply with proper glue. BISON
Clear Adhesive, UHU or similar are recommended as the most appropriate ones. Waterbased glue is
not recommended. The model can be built in on of two variants – North Korean night fighter or
Soviet long range escort fighter. You must choose the variant and print the necesery pages.
Preparation for assembling includes gluing the page 5 that contains the formers and strengthening
elements on a cardboard and cutting the transparent details from appropriate transparent foil.
Start with some subassemblings - undercarriage housings /parts 21-25/ and cockpit interior /parts 2*/
as shown on view A and B of the instruction drawings. Then prepare the wing superstructure /parts
20*/, following the vie C.
Assembly the wing /view D/ - parts 21 - 26. Watch out for the eventual twisting of the wing
segments and correct it before the complete drying of the glue.
Continue with the fuselage. The assembling sequence is shown on the vies E, F, G and H. Note that
every part is shown at least twice - as an exploded view and as a completed subassemblage in some
of the next views as well.
Glue the wings and tail to the fuselage, following view I.
Assembly the engine cowling, as shown on the view J. The forming of the nose with its air intakes is
a tricky job. If you prefer simplified assemblage, you can omit the internal surfaces of the engine
cowlings /parts 15* - 19*/ and use part 18c.
Following view K, assembly and glue to their places the propeller together with its shaft and bearing
/parts 19*, 42*-46*/, landing gear, Pitot tube and antenna masts.
Now your La-11 model is ready. You can enjoy it.
 La-11 Description

Designed as an all metal inheritor of the famous WW II wooden Lavochkin La 5 and 7,

encapsulating the latest Russian, American and German achievements in aerodynamics and piston
engines, this aircraft has remarkable flying characteristics. But it was too late - it was not capable to
compete with new jet powered fighters. La-11 saw military combat service in the Korean War as a
night fighter. Practically the aircraft itself was used as an executive part of the complicated weapon
system, that includes a ground radar detecting and guiding components. Without onboard radar, the
nightfighter has been guided from a ground radar station operator to nearness to the target. The final
approach, aiming and gunfire have been made visually, by using onboard searchlight, mounted on
the left wing of the aircraft.

La 11 Basic Performance
Powerplant Ash-82 FN
Power [hp] 1850
Length [m] 8,62
Wingspan [m] 9,80
Wing area [m2] 17,72
TOGW [kg] 3996
Operational range [km] 2550
Max. speed [km/h]
At s.l. 562
At 6200 m 690
Ceiling [m] 10250
Armament 3 x ÂÑ 23
mm
C 2002 E. ZARKOV
C 2002 E. ZARKOV
C 2002 E. ZARKOV
C 2002 E. ZARKOV
 C 2002 E. ZARKOV

1/32 scale La-11 Night Fighter PAGE 1

C 2002 E. ZARKOV 1/32 scale La-11 Night Fighter PAGE 2
 C 2002 E. ZARKOV

1/32 scale La-11 Night Fighter PAGE 3

C 2002 E. ZARKOV

1/32 scale La-11 Night Fighter PAGE 4

C 2002 E. ZARKOV
C 2002 E. ZARKOV
 C 2002 E. ZARKOV

TRANSPARENT PARTS

WARNING
USE ONLY TERMOPROOF
SPECIAL TRANSPARENT FOIL
FOR LASER PRINTING
OF THIS PAGE
USING UNAPROPRIATE MATERIAL
CAN BADLY DAMAGE YOUR
LASER PRINTER!
 MASTERING
LAVOCHKIN LA-11
The proposed LA-11 NIGHT FIGHTER model is
designed as a classic paper kit and is relatively easy
to be build. Despite its relative simplicity, a special
attention and precision in the assembly procedure is
required for achieving excellent results. Study
carefully the illustrative drawings, cutouts and
present instruction before starting the work on the
model. Try to imagine the separate assembly phases
and the purpose of each detail.

Do not be in a hurry with gluing - carefully check

and shape the details until obtain the exact and
correct fit. Before starting the work get hold of
the necessary tools:
scissors, sharp modeling knife,
blunt knife for scoring the fold lines,
prickle, ruler, nippers

After the acquaintance with the model, you may start the assemblage. Follow the sequence given
in the instruction. Cut the necessary details shortly before using them in order to avoid possible
mistakes. Score all fold lines before cutting the details. The places of scoring are marked with
small thin lines on the continuation of fold lines outside the parts.

You can find detailed description of the model’s

building sequence in the assembly instruction
supplied with this kit

If you are happy enough with your finished model, why don’t you take few pictures of it and share them with
C 2000 E. ZARKOV