Steady Heat Conduction

STEADY HEAT CONDUCTION
Introduction
• In heat transfer analysis, we are often interested in the rate of heat

transfer through a medium under steady conditions and surface
temperatures.
• The term “steady” implies no change with time at any point within the
medium, therefore, the temperature or heat flux remains unchanged
with time during steady heat transfer through a medium at any
location, although both quantities may vary from one location to
another.
• Such problems can be solved easily without involving any differential
equations by the introduction of the thermal resistance concept in an
analogous manner to electrical circuit problems.
STEADY HEAT CONDUCTION
1. CONDUCTION IN PLANE WALL
2. CONDUCTION IN CYLINDER & SPHERE
1. CONDUCTION IN PLANE WALL
• For one-dimensional conduction in a plane wall, heat is transferred in the
normal direction to the wall surface, and no significant heat transfer takes
place in the wall in other directions.
• The temperature distribution in the wall

under steady conditions is a straight line:
𝑥
𝑇 𝑥 = 𝑇2 − 𝑇1 + 𝑇1
𝐿
• The conduction heat transfer rate is:
𝑘𝐴
𝑄ሶ 𝑐𝑜𝑛𝑑,𝑤𝑎𝑙𝑙 = 𝑇1 − 𝑇2
𝐿
• The heat flux is:

𝑘
𝑞ሶ 𝑐𝑜𝑛𝑑,𝑤𝑎𝑙𝑙 = 𝑇1 − 𝑇2
𝐿
Thermal Resistance Concept
• In particular, there exists an analogy
between the diffusion of heat and
electrical charge.
• Just as an electrical resistance is
associated with the conduction of
electricity, a thermal resistance may be
associated with the conduction of heat.
• Defining resistance as the ratio of a
driving potential to the corresponding
transfer rate, the thermal resistances
in a plane wall 𝑹𝒘𝒂𝒍𝒍 is:
𝑇1 − 𝑇2
𝑄ሶ 𝑐𝑜𝑛𝑑,𝑤𝑎𝑙𝑙 = 𝑘𝐴
𝐿
𝑇1 − 𝑇2 Analogy between concepts of
= (a) thermal resistance
𝑅𝑤𝑎𝑙𝑙
(b) electrical resistance
𝐿
𝑅𝑤𝑎𝑙𝑙 =
𝑘𝐴
• A thermal resistance may also be associated with heat
transfer by convection at a surface. From Newton’s law
of cooling:
𝑇𝑠 − 𝑇∞
𝑄ሶ 𝑐𝑜𝑛𝑣 = ℎ𝐴𝑠 𝑇𝑠 − 𝑇∞ =
𝑅𝑐𝑜𝑛𝑣
• The convection resistance 𝑹𝒄𝒐𝒏𝒗 is then:
1
𝑅𝑐𝑜𝑛𝑣 =
ℎ𝐴𝑠
• When the wall is surrounded by a gas, the radiation

effects, which we have ignored so far, can be
significant and may need to be considered. From
radiation heat transfer:
𝑇𝑠 − 𝑇𝑠𝑢𝑟𝑟
𝑄ሶ 𝑟𝑎𝑑 = ℎ𝑟 𝐴𝑠 𝑇𝑠 − 𝑇𝑠𝑢𝑟𝑟 =
𝑅𝑐𝑜𝑛𝑣
• A radiation resistance 𝑹𝒓𝒂𝒅 may be defined as:
1
𝑅𝑟𝑎𝑑 =
ℎ𝑟 𝐴𝑠
Now consider steady one-dimensional conduction through a plane wall of thickness L,
area A, and thermal conductivity k. It is exposed to convection on both sides with heat
transfer coefficients 𝒉𝟏 and 𝒉𝟐 , and temperature 𝑻∞𝟏 > 𝑻𝟏 > 𝑻𝟐 > 𝑻∞𝟐 . Since 𝑸ሶ is
constant throughout the network, it follows that:
𝑇∞1 − 𝑇1 𝑇1 − 𝑇2 𝑇2 − 𝑇∞2
𝑸ሶ = = =
𝑅𝑐𝑜𝑛𝑣,1 𝑅𝑤𝑎𝑙𝑙 𝑅𝑐𝑜𝑛𝑣,2
The network can be expressed in total thermal resistance Rtotal as:
𝑇∞1 − 𝑇∞2
𝑸ሶ =
𝑹𝒕𝒐𝒕𝒂𝒍
Since the conduction and convection resistance are in series, it can be summed as below:
𝑹𝒕𝒐𝒕𝒂𝒍 = 𝑅𝑐𝑜𝑛𝑣,1 + 𝑅𝑤𝑎𝑙𝑙 + 𝑅𝑐𝑜𝑛𝑣,2
1 𝐿 1
𝑹𝒕𝒐𝒕𝒂𝒍 = + +
ℎ1 𝐴 𝑘𝐴 ℎ2 𝐴
Example 1
Consider a 0.8-m-high and 1.5-m-wide
glass window with a thickness of 8-mm
and a thermal conductivity of k = 0.78
W/m·K. Determine the steady rate of heat
transfer through this glass window and the
temperature of its inner surface for a day
during which the room is maintained at
20°C while the temperature of the
outdoors is 210°C. Take the heat transfer
coefficients on the inner and outer surfaces
of the window to be h1 = 10 W/m2·K and
h2 = 40 W/m2·K, which includes the
effects of radiation.
Example 2
Consider a 0.8-m-high and 1.5-m-wide
double-pane window consisting of two 4-
mm-thick layers of glass (k = 0.78
W/m·K) separated by a 10-mm-wide
stagnant air space (k = 0.026 W/m·K).
Determine the steady rate of heat transfer
through this double-pane window and the
temperature of its inner surface for a day
during which the room is maintained at
20°C while the temperature of the
outdoors is -10°C. Take the convection
heat transfer coefficients on the inner and
outer surfaces of the window to be h1 =
10 W/m2·K and h2 = 40 W/m2·K, which
includes the effects of radiation.
Thermal Contact Resistance
• In the analysis of heat conduction through multilayer solids, we assumed
“perfect contact” at the interface of two layers, and thus no temperature
drop at the interface. This would be the case when the surfaces are
perfectly smooth and they produce a perfect contact at each point.
• In reality, however, a surface is microscopically rough no matter how
smooth it appears to be. As a result, an interface contains numerous air
gaps of varying sizes that act as insulation because of the low thermal
conductivity of air.
Ideal (perfect) Actual (imperfect)

thermal contact thermal contact
• Consider heat transfer through a cross-
sectional area A that are pressed against
each other, with the effective temperature
difference at the interface ∆𝑻𝒊𝒏𝒕𝒆𝒓𝒇𝒂𝒄𝒆 .
• It can be expressed analogously to
Newton’s law of cooling using contact
conductance hc :
𝑄ሶ = ℎ𝑐 𝐴∆𝑇𝑖𝑛𝑡𝑒𝑟𝑓𝑎𝑐𝑒
𝑄ሶ Τ𝐴
ℎ𝑐 =
∆𝑇𝑖𝑛𝑡𝑒𝑟𝑓𝑎𝑐𝑒
• This resistance for a unit area is called the contact resistance Rc , which is
the inverse of hc . Then the interface resistance 𝑹𝒊𝒏𝒕𝒆𝒓𝒇𝒂𝒄𝒆 is expressed as:
1 ∆𝑇𝑖𝑛𝑡𝑒𝑟𝑓𝑎𝑐𝑒 1 𝑅𝑐
𝑅𝑐 = = 𝑅𝑖𝑛𝑡𝑒𝑟𝑓𝑎𝑐𝑒 = =
ℎ𝑐 𝑄ሶ Τ𝐴 ℎ𝑐 𝐴 𝐴
Example 3
Four identical power transistors with aluminum
casing are attached on one side of a 1-cm-thick
20-cm × 20-cm square copper plate (k = 386
W/m·K) by screws that exert an average pressure
of 6 MPa. The base area of each transistor is 8
cm2, and each transistor is placed at the center of
a 10-cm × 10-cm quarter section of the plate.
The interface roughness is estimated to be about
1.5 mm. All transistors are covered by a thick
Plexiglas layer, which is a poor conductor of
heat, and thus all the heat generated at the
junction of the transistor must be dissipated to
the ambient at 20°C through the back surface of
the copper plate. The combined convection/
radiation heat transfer coefficient at the back
surface can be taken to be 25 W/m2·K. If the
case temperature of the transistor is not to exceed
70°C, determine the maximum power each
transistor can dissipate safely, and the
temperature jump at the case–plate interface.
Generalized Thermal Resistance Networks
Although problem that involve parallel layers or combined series-parallel
arrangements are often two- or three-dimensional, approximate solutions can be
obtained by assuming one-dimensional heat transfer and using the thermal
resistance network.
Thermal resistance network for two Thermal resistance network for

parallel layers. combined series-parallel arrangement.
Example 4
A 3-m-high and 5-m-wide wall consists of
long 16-cm x 22-cm cross section horizontal
bricks (k = 0.72 W/m·K) separated by 3-cm-
thick plaster layers (k = 0.22 W/m·K). There
are also 2-cm-thick plaster layers on each side
of the brick and a 3-cm-thick rigid foam (k =
0.026 W/m·K) on the inner side of the wall, as
shown in fig. here. The indoor and the outdoor
temperatures are 20°C and -10°C,
respectively, and the convection heat transfer
coefficients on the inner and the outer sides
are h1 = 10 W/m2·K and h2 = 25 W/m2·K,
respectively. Assuming one-dimensional heat
transfer and disregarding radiation, determine
the rate of heat transfer through the wall.
2. CONDUCTION IN CYLINDER & SPHERE
• The cylindrical and spherical systems often experience temperature
gradients in the radial direction only and may therefore be treated as one-
dimensional.
• Moreover, under steady-state conditions with no heat generation, such
systems can be further simplified.
• The cylindrical systems can be analyzed
by using the appropriate form of the
heat equation, given that cross-
sectional area A normal to the direction
of heat transfer is:
𝐴 = 2𝜋𝑟𝐿
• The spherical systems can be analyzed
by using the appropriate form of
Fourier’s law, given that cross-sectional
area A normal to the direction of heat
transfer is:
𝐴 = 4𝜋𝑟 2
• In steady operation, there is no change in
the temperature of the cylindrical pipe
or spherical shell with time at any point.
• Therefore, heat transfer through the
cylinder 𝑸ሶ 𝒄𝒐𝒏𝒅,𝒄𝒚𝒍 or sphere 𝑸ሶ 𝒄𝒐𝒏𝒅,𝒔𝒑𝒉
must be constant.
• The thermal resistances for cylinder
𝑹𝒄𝒚𝒍 and sphere 𝑹𝒔𝒑𝒉 are defined based
on cross-sectional area A.
Cylindrical Spherical
𝑇1 − 𝑇2 𝑇1 − 𝑇2
𝑄ሶ 𝑐𝑜𝑛𝑑,𝑐𝑦𝑙 = 𝑄ሶ 𝑐𝑜𝑛𝑑,𝑠𝑝ℎ =
𝑅𝑐𝑦𝑙 𝑅𝑠𝑝ℎ
ln 𝑟2 /𝑟1 𝑟2 − 𝑟1
𝑅𝑐𝑦𝑙 = 𝑅𝑠𝑝ℎ =
2𝜋𝐿𝑘 4𝜋𝑟1 𝑟2 𝑘
Now consider steady one-dimensional
conduction through a cylindrical (or
spherical) shell subjected to
convection from both the inner and the
outer sides. Since 𝑸ሶ is constant, then:
𝑇∞1 − 𝑇∞2
ሶ
𝑸=
𝑹𝒕𝒐𝒕𝒂𝒍
For cylindrical, is:
𝑹𝒕𝒐𝒕𝒂𝒍 = 𝑅𝑐𝑜𝑛𝑣,1 + 𝑅𝑐𝑦𝑙 + 𝑅𝑐𝑜𝑛𝑣,2

1 ln 𝑟2 /𝑟1 1
2𝜋𝑟1 𝐿 ℎ1 2𝜋𝐿𝑘 2𝜋𝑟2 𝐿 ℎ2
For spherical, is:
𝑹𝒕𝒐𝒕𝒂𝒍 = 𝑅𝑐𝑜𝑛𝑣,1 + 𝑅𝑠𝑝ℎ + 𝑅𝑐𝑜𝑛𝑣,2

1 𝑟2 − 𝑟1 1
4𝜋𝑟12 ℎ1 4𝜋𝑟1 𝑟2 𝑘 4𝜋𝑟22 𝐿 ℎ2
Summary
Elementary thermal resistance relations

Example 5
A 3-m internal diameter spherical tank made
of 2-cm-thick stainless steel (k = 15 W/m·K)
is used to store iced water at T∞1 = 0°C. The
tank is located in a room whose temperature is
T∞2 = 22°C. The walls of the room are also at
22°C. The outer surface of the tank is black
and heat transfer between the outer surface of
the tank and the surroundings is by natural
convection and radiation. The convection heat
transfer coefficients at the inner and the outer
surfaces of the tank are h1 = 80 W/m2·K and
h2 = 10 W/m2·K, respectively. Determine:
a) Rate of heat transfer to the iced water in
the tank.
b) Amount of ice at 0°C that melts during a
24-h period.
Example 6
Steam at T∞1 = 320°C flows in a cast iron
pipe (k = 80 W/m·K) whose inner and outer
diameters are D1 = 5 cm and D2 = 5.5 cm,
respectively. The pipe is covered with 3-
cm-thick glass wool insulation with k =
0.05 W/m·K. Heat is lost to the
surroundings at T∞2 = 5°C by natural
convection and radiation, with a combined
heat transfer coefficient of h2 = 18 W/m2·K.
Taking the heat transfer coefficient inside
the pipe to be h1 = 60 W/m2·K, determine:
a) Rate of heat loss from the steam per
unit length of the pipe.
b) Temperature drops across the pipe
shell and the insulation.
Critical Radius of Insulation
• For plane wall, the thicker the insulation, the lower the heat transfer rate.
This is expected, since the cross-sectional area A is constant, and adding
insulation always increases the thermal resistance of the wall without
increasing the convection resistance.
• However, adding insulation for cylindrical or spherical is a different
matter. The additional insulation increases the conduction resistance of
the insulation layer, but decreases the convection resistance of the surface
because of the increase in the outer surface area for convection.
• Consider a cylindrical pipe of 𝒓𝟏 with 𝑻𝟏
which is maintained constant. The pipe is
now insulated with a material of 𝒓𝟐 with 𝒌.
• Heat is lost from the pipe to the
surrounding medium through convection
at 𝑻∞ with a 𝒉.
• The 𝑸ሶ from 𝑻𝟏 to 𝑻∞ is expressed as:
𝑇1 − 𝑇∞
𝑄ሶ =
𝑅𝑐𝑦𝑙 + 𝑅𝑐𝑜𝑛𝑣
• The variation of 𝑸ሶ with the outer radius
of the insulation 𝒓𝟐 is plotted. The 𝑸ሶ
reaches a maximum at zero slope.
• Performing the differentiation and
solving for 𝒓𝟐 yields the critical radius
of insulation 𝒓𝒄𝒓 .
• For the cylindrical pipe:
𝑘
𝑟𝑐𝑟,𝑐𝑦𝑙 =
ℎ
• Repeat the same with spherical shell:

2𝑘
𝑟𝑐𝑟,𝑠𝑝ℎ =
ℎ
• Note that the 𝒓𝒄𝒓 depends on the insulation 𝒌 and the external 𝒉.
• The 𝑸ሶ increases with the addition of insulation for 𝒓𝟐 < 𝒓𝒄𝒓 , reaches a
maximum when 𝒓𝟐 = 𝒓𝒄𝒓 , and starts to decrease for 𝒓𝟐 > 𝒓𝒄𝒓 .
• Thus, insulating the pipe may actually increase the rate of heat transfer
from the pipe instead of decreasing it when 𝒓𝟐 < 𝒓𝒄𝒓 .
Example 7
A 3-mm-diameter and 5-m-long electric
wire is tightly wrapped with a 2-mm
thick plastic cover whose thermal
conductivity is k = 0.15 W/m·K.
Electrical measurements indicate that a
current of 10 A passes through the wire
and there is a voltage drop of 8 V along
the wire. If the insulated wire is exposed
to a medium at T∞ = 30°C with a heat
transfer coefficient of h = 12 W/m2·K,
determine the temperature at the
interface of the wire and the plastic
cover in steady operation. Also
determine whether doubling the
thickness of the plastic cover will
increase or decrease this interface
temperature.

Steady Heat Conduction

Uploaded by

Copyright:

Available Formats

Steady Heat Conduction

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Steady Heat Conduction

Uploaded by

Copyright:

Available Formats

STEADY HEAT CONDUCTION

• In heat transfer analysis, we are often interested in the rate of heat

• The temperature distribution in the wall

• The heat flux is:

• When the wall is surrounded by a gas, the radiation

𝑹𝒕𝒐𝒕𝒂𝒍 = 𝑅𝑐𝑜𝑛𝑣,1 + 𝑅𝑤𝑎𝑙𝑙 + 𝑅𝑐𝑜𝑛𝑣,2

Ideal (perfect) Actual (imperfect)

Thermal resistance network for two Thermal resistance network for

𝑹𝒕𝒐𝒕𝒂𝒍 = 𝑅𝑐𝑜𝑛𝑣,1 + 𝑅𝑐𝑦𝑙 + 𝑅𝑐𝑜𝑛𝑣,2

For spherical, is:

𝑹𝒕𝒐𝒕𝒂𝒍 = 𝑅𝑐𝑜𝑛𝑣,1 + 𝑅𝑠𝑝ℎ + 𝑅𝑐𝑜𝑛𝑣,2

Elementary thermal resistance relations

• Repeat the same with spherical shell:

You might also like