Gas Lift Equipment

TABLE OF CONTENT

Description Page
SIDE POCKET MANDREL (WRVM) Pg.1
SIDE POCKET MANDREL-ROUND BODY Pg.2
SIDE POCKET MANDREL-CHEMICAL INJECTION Pg.3
GBK-2 (OIL-GBK2-1.358-JK-B05) & GRK (OIL-GRK-1.787-RK1-B05) LATCHES Pg.4
GRA LATCH (OIL-GRA-1.750-JC3-B05) Pg.4
RD DUMMY VALVE (OIL-RDDV-1.1/2-GRK-B05) Pg.5
E DUMMY VALVE (OIL-EDV-1000-GBK2-B05) Pg.5
OILOG MODEL BDK-1 DUMMY VALVE (OIL-BDK1DV-1000-GA2-B05) Pg.6
‘O’ SERIES ORIFICE VALVES Pg.7
OILOG BDKO-1 RETRIEVABLE SINGLE POINT INJECTION ORIFACE VALVE
(OIL-BDKO1-1000-GA2-B05) Pg.8
GR-40 INJECTION PRESSURE OPERATED GAS LIFT VALVE OIL-IPOGLV-1000-
JKBC1-B05 Pg.9
GR-20 INJECTION PRESSURE OPERATED GAS LIFT VALVE Pg.10
MODEL BBK-1 GAS LIFT VALVE (OIL-BBK1GLV-1000-GA2-B05) Pg.11
RETRIEVABLE CHEMICAL INJECTION VALVE Pg.12
KICKOVER TOOL Pg.13
G-40 GAS LIFT VALVE Pg.14
G-20 GAS LIFT VALVE Pg.15
G-40 CHECK VALVE Pg.16
G-20 CHECK VALVE Pg.16
MODEL ‘B’ CONVENTIONAL GAS LIFT MANDREL Pg.17
MODEL ‘C’ CONVENTIONAL GAS LIFT MANDREL Pg.17
BK-2 LATCH Pg.18
RK LATCH Pg.18
RA LATCH Pg.19
DK DUMMY VALVE Pg.20
RD DUMMY VALVE Pg.20
 MACHINING:
SIDE POCKET MANDREL (WRVM) Pockets are machined using Deep Hole Drilling & boring
Product No. OIL-SPM-0000-0000-B05 process that provides accurate polished bore diameters,
alignment and better surface finish for packing seals. The
OILOG Side Pocket Mandrels allow use of standard swages are machined with precision accuracy. Threads are
Wireline tools for installation and retrieval of different types machined as per design specification. All components are
of flow control devices. dimensionally inspected.
WELDING HEAT TREATMENT:
MATERIALS: Welding is done as per ASME Section VIII & IX with the use of
Generally Low Alloy Steel AISI 4130 is used. proper welding electrodes. Full penetration welds take place
For corrosive application, AISI 410 is used. when joining the swages and forged pocket are welded to the
Other materials may be used as per oval pipe. After welding, all external weld deposits are evenly
customer’s requirement. grounded down to match the outside profile. All mandrels are
FORGINGS: heat treated, Quenched & Tempered to 18-22 HRC, for
Pockets & tool discriminators are closed die forged corrosive service and 24-33 HRC for standard service
and are integral part of the pocket. Swages are forged from application.
seamless mechanical tubing or it can be machined from solid ASSEMBLED MANDREL:
bar stock. Forgings are made by using a precision closed die After heat treatment and threading each mandrel is tested for
process. All forged parts are visually and dimensionally hardness, internal and external drift and pressure test.
inspected by Quality Control before machining. After Heat Additional testing i.e. dye penetrant, ultrasonic, magnetic
Treatment, additional testing i.e. Grain Flow, Micro particle and radiography can also be provided as per customer
Examination, Hardness Testing, Dye Penetrant Testing requirement.
Magnetic Particle Testing & Ultra Sonic Testing are also
carried out.

Other Drift sizes can also be provided upon request.

• Test pressure given are for mandrels made of aisi-4130 (9Cr 1 Mo, 13
Cr) materials heat treated for Standard or Corrosive environments.
Test Pressure may be reduced due to end connection limitations.
1 • Weight & Length may vary depending upon end connection.
SIDE POCKET MANDREL-ROUND BODY
Product No. OIL-SPMRB-0000-000-B05
OILOG Side Pocket Mandrels allow use of standard HOW TO ORDER:
Wireline tools for installation and retrieval of different SIDE POCKET MANDREL-ROUND BODY FOR
types of flow control devices. TUBING 2-3/8” VALVE OD 1.0”
PRODUCT NO. OIL-SPMCI-2375-1000-B05
MATERIALS:
Generally Low Alloy Steel AISI 4130 is used.
For corrosive application, AISI 410 is used.
Other materials may be used as per customer’s
requirement.

FEATURES & BENIFITS:

• The high-pressure design allows use of these
mandrels in deep applications requiring high
pressure and/or tensile ratings.
• The machined pocket and tool guard protect gas-lift
equipment by preventing tools larger than the
pulling/running tool

2
SIDE POCKET MANDREL-CHEMICAL INJECTION
Product No. OIL-SPMCI-0000-000-B05

HOW TO ORDER:
SIDE POCKET MANDREL-CHEMICAL INJECTION FOR
TUBING 2-3/8” VALVE OD 1.5”
PRODUCT NO. OIL-SPMCI-2375-1500-B05

3
GBK-2 (OIL-GBK2-1.358-JK-B05) & GRA LATCH (OIL-GRA-1.750-JC3-B05)
GRK (OIL-GRK-1.787-RK1-B05)
LATCHES
OILOG Wireline retrievable latches 1” GBK-2 and The GRA Latch is a cam style latch used to secure a 1 ½”
1 ½” GRK are designed for installation in G-type O.D. valve (Non- Orienting) or dummy in “MM” and
pocket profile Side Pocket Mandrels (B1M & “MMA” Mandrels.
B2M). They utilize a locking ring which is held in
position by spring forces. As the latch enters the The latch utilizes a rotating spring loaded cam to lock in
Side Pocket profile, the locking ring moves up and place when the latch reaches the recess in the mandrel
into the recessed area of the latch. When the receiver pocket. The latch also has 2 O-Rings to provide a
latch seats, the ring is positioned in the locking better top seal and debris barrier. A pin is sheared to
recess of the pocket. To retrieve the latch, a pin is release the locking mechanism allowing the cam to
sheared by upward force allowing the locking ring rotate inside the latch housing and permitting the
mandrel to move up and out of the way. The ring retrieval of the valve or dummy.
is then freed to disengage from the locking recess
as the valve and latch are retrieved.

4
RD DUMMY VALVE (OIL-RDDV-1500-GRK-B05) E DUMMY VALVE (OIL-EDV-1000-GBK2-B05)

The RD Dummy Valve is 1 ½” Wireline Retrievable The E Dummy Valve is 1 Wireline Retrievable Isolation
Isolation Tool which is used to seal of the M / TP Tool which is used to seal of the K / TMP series
series Mandrel (B2M) preventing communication Mandrel (B1M) preventing communication between
between the Casing & Tubing. the Casing & Tubing.
The Dummy valve with the appropriate Latch may be The Dummy valve with the appropriate Latch may be
Wireline installed or retrieved prior to or after Wireline installed or retrieved prior to or after
completion for various procedures which include completion for various procedures which include
following: following:

1. To blank off the tubing for production until gas 1. To blank off the tubing for production until gas lift
lift valves are required. valves are required.
2. To allow for pressurizing the tubing in various 2. To allow for pressurizing the tubing in various
procedures. procedures.
3. To isolate Tubing & Casing flow during single 3. To isolate Tubing & Casing flow during single
alternative production and alternative production .
4. To isolate Tubing & Casing flow for test purpose 4. To isolate Tubing & Casing flow for test purpose
during multi-point water or gas injection floods. during multi-point water or gas injection floods.

5
OILOG MODEL BDK-1 DUMMY VALVE
(OIL-BDK1DV-1000-INT0-B05)
OILOG BDK-1 Dummy Valve serves the same purpose as E
Dummy Valve but comes complete with attached top
running head & bottom collet latch. The BDK-1 Dummy
Valve is 1 Wireline Retrievable Isolation Tool which is
used to seal of the K / TMP series Mandrel (B1M)
preventing communication between the Casing & Tubing.
The Dummy valve with the appropriate Latch may be
Wireline installed or retrieved prior to or after
completion for various procedures which include
following:

1. To blank off the tubing for production until gas lift

valves are required.

2. To allow for pressurizing the tubing in various

procedures.

3. To isolate Tubing & Casing flow during single

alternative production and

4. To isolate Tubing & Casing flow for test purpose

during multi-point water or gas
injection floods.

6
‘O’ SERIES ORIFICE VALVES
Product No. OIL-OSOF-1000-GRO40-B05
OIL-OSOF-1500-GRO20-B05
OILOG O Series 1” & 1-1/2” valves are designed for
circulating operations and provide means for communication
between the tubing and the tubing/casing annulus.

FEATURES & BENEFITS

• Flow capacity determined by orifice sizing.
• Integral reverse flow check valve provides large flow
capacities. Positive sealing feature of back check valve
provides protection from intrusion of production fluids
into casing annulus.
• Various orifice materials (SS, Monel, Inconel, tungsten
carbide) available to meet application requirements.
• Temperature rating of 250º F (121º C) (Standard
Service).
• Standard Neoprene packing with other materials
available.
• Compatible with other manufacturers side Pocket
Mandrel (TMP/TP).

APPLICATIONS
The Wireline retrievable orifice valves are used to establish
communication between the tubing & annulus during
circulating, gas or fluid injection operations. They are utilized
in single point injection continuous flow completions. These
valve have no closing function and are commonly used to
control stable injection at the operating
valve depth.

7
OILOG BDKO-1 RETRIEVABLE SINGLE POINT
INJECTION ORIFICE VALVE
(OIL-BDKO1-1000-INT0-B05)
OILOG BDKO-1 is a single point injection Valve
used for continuous flow gas lift production.
An integral choke controls the flow of gas
through the normally opened valve and into the
production conduit. Reverse flow checks are
included as an integral part of these valves.
The valve containing a replaceable choke with
3/8” Max Port size. Other available port sizes
are 1/8”, 3/16”, 1/4”, 5/6” & 3/8”.

OPERATION:
Injection gas enters the valve through the
external parts located between the packing
sets. It then travels through the choke,
passed a reverse flow check & into the
production conduit.

8
GR-40 INJECTION PRESSURE
OPERATED GAS LIFT VALVE
Product No. OIL-GR40IP-1000-GBK2-B05

OILOG G Series valve utilizes nitrogen charged bellow

configuration designed for either continuous or
intermittent flow applications. They are especially
suitable for use as unloading and operating valves
in areas where high gas lift pressures are available.
Since the charge pressure above the bellows is
affected by temperature, it is important that the
operating temperatures at the valve be known. These
valves are available in Wireline installations.

ADVANTAGES
Vibration protected 3-ply Monel bellow are designed to
withstand hydrostatic pressure up to 5000 psi. Nitrogen
dome charge, acting on the O.D. of the bellow, permits
bellows to expand uniformly without stacking, thus
prolonging bellow’s life. The multiple port size
availability, make this valve series appropriate for a
wide range of operating conditions. Reversible seat are
available in several different materials.

9
GR-20 INJECTION PRESSURE OPERATED GAS LIFT
VALVE
Product No. OIL-GR20IPOG-1500-GRK0-B05

DESCRIPTION

OILOG G Series valve utilizes nitrogen charged bellow

configuration designed for either continuous or
intermittent flow applications. They are especially
suitable for use as unloading and operating valves in
areas where high gas lift pressures are available. Since
the charge pressure above the bellows is affected by
temperature, it is important that the operating
temperatures at the valve be known. These valves are
available in Wireline installations.

ADVANTAGES

Vibration protected 3-ply Monel bellow are designed

to withstand hydrostatic pressure up to 5000 psi.
Nitrogen dome charge, acting on the O.D. of the
bellow, permits bellows to expand uniformly without
stacking, thus prolonging bellow’s life. The multiple
port size availability, make this valve series appropriate
for a wide range of operating conditions. Reversible
seat are available in several different materials.

10
MODEL BBK-1 GAS LIFT VALVE
(OIL-GLV-1000-BBK1-B05)

DESCRIPTION
OILOG G Series valve utilizes nitrogen charged bellow configuration designed for either
continuous or intermittent flow applications. They are especially suitable for use as unloading
and operating valves in areas where high gas lift pressures are available. Since the charge
pressure above the bellows is affected by temperature, it is important that the operating
temperatures at the valve be known. These valves are available in Wire line installations.

ADVANTAGES
Vibration protected 3-ply Monel bellow are designed to withstand hydrostatic pressure up to
5000 psi. Nitrogen dome charge, acting on the O.D. of the bellow, permits bellows to expand
uniformly without stacking, thus prolonging bellow’s life. The multiple port size availability,
make this valve series appropriate for a wide range of operating conditions. Reversible seat
are available in several different materials.

OPERATING PRINCIPLE
The dome nitrogen charge applied to the external area of the bellows provides the downward
force, holding the valve on its seat. This dome pressure is preset at the reference temperature
and corrected to operating temperature. The opening forces on the valve are the casing
pressure acting on the internal area of the bellows (less the area of the seat) and the tubing
pressure acting on the seat area. When the combined Casing & Tubing pressures are sufficient,
the valve opens. Once the valve is open, it remains open until the casing pressure is reduced to
predetermined closing pressure. The spread (the difference between opening & closing casing
pressure) is controlled by the tubing sensitivity of the valve. The larger the seat port area, the
more tubing sensitive the valve is.
The BBK-1 Gas Lift Valve is designed with an integral bottom collet latch which locks the valve
in the Side Pocket of the Gas Lift Mandrel. Once the valve has locked the Side Pocket of the
mandrel, downward jarring causes the collet dog of the latch to engage in the locking recess
provided in the side pocket. To pull the Valve, upward jarring is required. The upward jarring
shears the brass shear pin securing the shear ring to the latch body. As the BBK-1 valve is
pulled upward in the Side Pocket, the shoulder on the Latch body moves out from behind the
collet dog. The collet fingers are deflected inward and disengage from the locking recesses of
the mandrel pocket. The valve is then free from the mandrel pocket and can be removed from
the valve.

11
RETRIEVABLE CHEMICAL OPERATION
Injected chemicals enter the valves from the annulus in an
INJECTION VALVE open injection system. Chemicals also may enter the valve
Product No. from a separate injection line as in a closed injection system.
The hydraulic pressure of the injected chemicals compresses
OIL-RCIV-1000-BCLK-B05 the bellow/spring & lift the stem tip of the seat & open the
OIL-RCIV-1000-BCLK1-B05 valve. Chemicals then flow through the valve into the
production conduit.
OIL-RCIV-1000-BCLK2-B05
OIL-RCIV-1500-BCLK3-B05

OILOG BCLK & BCLK-1 Chemical injection valves are 1” OD valve

designed to control chemicals injected in to the production fluid at
valve depth. A Nitrogen charged bellows provides the force
necessary to maintain each valve in its normally closed position.
The BCLK contain a 3 ply Inconel bellows, which suits this valve for
high pressure service. The BCLK-1 contains a 3 ply Monel bellows
and is used for lower pressure applications. Bellow area is 0.26
square inch for both valves. Valves contain spring
loaded reverse flow checks, required GBK-2 top latch & are run in
the appropriate B1M series mandrels. Port size available for the
BCLK & BCLK-1 valves are 1/8” & 3/16”.

OILOG also design BCLK-2 & BCLK-3 Chemical injection valve which
are Side pocket valves designed to control
chemicals injected in to the production fluid at valve depth. An
Inconel spring provides the force necessary to maintain each valves
in its normally closed position. The BCLK-2 is for 1” OD & BCLK-3 is
for 1-1/2” OD. The
BCLK-2 to utilize a GBK-2 top latch (B1M SPM) & BCLK-3 to utilize a
GR series latch(B2M SPM). Reverse flow checks are included as an
integral port of these valves.
Port size available for the BCLK-2 & BCLK-3 valves are 1/8” & 3/16”.

12
KICKOVER TOOL
PRODUCT NO.
OIL-KOT-BK5-0000-B05
OIL-KOT-BM1-0000-B05
Introduction and Application

The OILOG BK-5 & BM-1 kickover tools are used to install
and retrieve 1” and 1-1/2” O.D flow control devices in OILOG
B1M/B1HO and B2M/B2HO series side pocket mandrels.
The kickover tool is lowered into the well by standard
wireline techniques until the tool is below the selected
mandrel. As the tool string is raised, the locator finger of the
kickover tool contacts the top of the slot in the orienting
sleeve in the mandrel, and the kick spring pivots the lower
section of the kickover tool, the pulling or running tool and
the valve into the kickover position. The orienting sleeve in
the mandrel provides positive installation and retrieval of
the flow control device by the kickover tool. Once the flow
control device is installed or retrieved, and the wireline
operator raises the kickover tool the latch spring is
compressed thus permitting the kickover tool to pass
through all mandrels above the one in which the wireline
operation was performed.

KICKOVER TOOL - BK-5 KICKOVER TOOL - BM-1

PRODUCT NO. PRODUCT NO.
OIL-KOT-BK5-2000-B05 OIL-KOT-BM1-2500-B05
OIL-KOT-BK5-2500-B05 OIL-KOT-BM1-3000-B05
OIL-KOT-BK5-3000-B05 OIL-KOT-BM1-4500-B05
OIL-KOT-BK5-4500-B05 OIL-KOT-BM1-5500-B05

13
G-40 Gas Lift Valve Product
No. OIL-GLVG40-1000-0000-B05
Introduction
The G-40 conventional gas lift valve is a 1” O.D
pressure operated valve. It can be used for
either continuous or intermitting flow and is
installed with a reverse check valve on the
conventional tubing retrievable gas lift
mandrel. OILOG gas lift valve is available in 1/8”
to 3/8” Port sizes or as required.

Product Description
The 1” OD (G-40) conventional valves are
Nitrogen charged gas lift valves which can be
used as an intermittent valve or a continuous
flow valve. N2 dome pressure is set in a shop at
a reference temperature and corrected to an
operating depth temperature. The N2 charge
inside the bellow provides a downward force
tending to hold the valve on its seat.
The upward forces necessary to open the valve
are casing pressure acting on the bellow area is
less than seat area & tubing pressure acting on
the seat area. When these combined pressures
are sufficient, the valve will open. Once opened
it will remain open until casing and tubing
pressure are reduced to/ or below set dome
pressure. The difference between opening and
closing pressure is called Spread. It is controlled
by tubing pressure sensitivity of the valve.
Larger the seat port area, the more is the tubing
sensitive valve.

Valve Specifications:

1. Material: Stainless Steel

Standard.
2. Pressure Rating: High range as
per API 11V1 1200 Psi and
above.
3. Temperature Rating: 300ºF.

14
G-20 Gas Lift Valve
Product No.
OIL-GLVG20-1500-0000-B05
The G-20 conventional gas lift valve is a 1-1/2”
O.D Pressure operated nitrogen charged valve.
It can be used for either continuous or
intermitting flow and is installed with a reverse
check valve on the conventional tubing
retrievable class mandrels. Port sizes available
1/8”to 1/2” or as required. N2 dome pressure
is set in a shop at a reference temperature and
corrected to an operating depth temperature.
The N2 charge inside the bellow provides a
downward force tending to hold the valve on
its seat. The upward forces necessary to open
the valve are casing pressure acting on the
bellow area is less than seat area & tubing
pressure acting on the seat area. When these
combined pressures are sufficient, the valve
will open. Once opened it will remain open
until casing and tubing pressure are reduced
to/ or below set dome pressure. The difference
between opening and closing pressure is called
Spread. It is controlled by tubing pressure
sensitivity of the valve. Larger the seat port
area, the more is the tubing sensitive valve.

Valve Specifications:
1. Material: Stainless
Steel Standard.
2. Pressure Rating: High
range as per API 11V1
1200 Psi and above.
3. Temperature Rating:
300ºF.

15
G-40 CHECK VALVE G-20 CHECK VALVE
Product No. Product No.
OIL-CHV-1000-G40-B05 OIL-CHV-1500-G20-B05

G-40 check valves are used with G-40 G-20 Check valves are used with G-20
conventional gas lift valve to protect the conventional gas lift valve to protect the
casing from backflow, allowing the tubing to casing from backflow, allow for pressurizing
be pressurizing in various procedures, and the tubing in various procedures, and prevent
prevent any commingling of fluids in dual any commingling of flow in dual installation.
installation. The conventional check The conventional check assemblies utilize the
assemblies utilizes the same metal to metal same metal to metal seal as well as metal dart
seal as well as metal dart to soft hy-car pad to soft hy – car pad seal as does the
seal as does the retrievable valve checks. The retrievable valve checks. The G-20 check is a
G-40 check is a velocity type check requiring velocity type check requiring flow pressure to
flow pressure to force the dart on seat but is force the dart on seal but is also available in a
also available in a normally closed variation normally closed variation with a spring
with a spring attachment. G-40 check valves attachment. G-20 is a reverse flow check with
are of the same design as the G-20 but all the characteristics of the G-20 check but
designed for used with the 1” conventional G- designed for use with the 1 ½” conventional
40 valve the dart, seal and pad are of the same casing flow valve.
design as the K series, retrievable valves.
GCF-40 is a reverse flow check with all the
characteristics of the G-40 check but designed
for use with the 1” conventional casing flow
valve.

16
MODEL ‘B’ CONVENTIONAL GAS
LIFT MANDREL
Product No. OIL-BGLM-1000-0000-B05
The Model ‘B’ mandrels are designed to
accept the 1” conventional G-40
pressure operated gas lift valve and G-40
tubing flow check Valve. The Mandrels
are manufactured with side guards to
protect the valve when running or
pulling the tubing string. These mandrels
are available in various tubing grades
such as J-55, N-80, L-80, P-110 & other
grades of material as per customer
requirement.

MODEL ‘C’ CONVENTIONAL GAS

LIFT MANDREL
Product No. OIL-CGLM-1500-0000-B05

The Model ‘C’ mandrels are designed to

accept the 1-1/2” conventional G-20
pressure operated gas lift valve and G-20
tubing flow check Valve. The Mandrels are
manufactured with side guards to protect
the valve when running or pulling the
tubing string. These mandrels are
available in various tubing grades such as
J-55, N-80, L-80, P-110 & other grades of
material as per customer requirement.

17
 BK-2 LATCH
PART NUMBER
Assembly OIL-BK2LT-0000-0000-W01

COMPONENTS
Post
Skirt
Ring
Spring
Bottom

RK LATCH

PART NUMBER
Assembly OIL-RKLT-0000-0000-W01

COMPONENTS
Post
Skirt
Ring
Spring
Bottom

18
 RA LATCH

PART NUMBER
Assembly OIL-RALT-0000-0000-W01

COMPONENTS
Nose
Body
Post
Cam
Spring
Pin
O-ring

19
 DK DUMMY VALVE
PART NUMBER
1" Assembly OIL-DKDMV-1000-0000-W01

RD DUMMY VALVE

PART NUMBER
1 1/2" Assembly OIL-RDDMV-1500-0000-W01

* Side Pocket Mandrels Available Upon Request

* Gas Lift Valves Available Upon Request

20
 Oilog, Inc
10370 Richmond Ave. Ste 895.
Houston, TX 77042

General Information at: info@oilog.com

Phone: 832-778-8811 Fax: 713-339-9924