Heat Exchanger

EXPERIMENT NO.
2
OBJECTIVE:
To determine the effectiveness of Shell and Tube Heat Exchanger for parallel flow.
INTRODUCTION:
In many process industries it is a frequent necessity to heat, cool, vapourize and condense
various fluid streams. Different types of heat transfer equipments are used for such purposes.
Heat Exchanger is a device in which two fluid streams, one hot and another cold are brought
into thermal contact in order to affect transfer of heat from hot fluid stream to the cold. It
provides a relatively large area for heat transfer for a given volume of the equipment.
The simplest type of heat exchanger is a double-pipe heat exchanger in which one fluid flows
through the annular space between the inner and outer pipes. In the design of heat exchanger
one should take into account the following important factors:
 THE THERMAL ANALYSIS-

In this phase of design one is primarily concerned with the estimation of heat transfer
area for the transfer of heat at a specified rate for the given flow rates and temperature
of the fluids.
 THE MECHANICAL DESIGN-
In this phase of design one takes into account the operating temperatures, pressures,
corrosive nature of the fluids, pressure drop, thermal stresses etc.
 THE DESIGN FOR THE MANUFACTURER
In this phase of design, one concentrates on the selection of the material, seals,
enclosures, cost of manufacturing procedures.
THEORY:
The shell and tube heat exchanger is commonly used in the food and chemical process
industries. This type of exchanger consists of a number of tubes in parallel enclosed in a
cylindrical shell. Heat is transferred between one fluid flowing through the tubes and another
fluid flowing through the cylindrical shell around the tubes.
a shell and tube heat exchanger
In this miniature exchanger, baffles inside the shell increase the velocity of the fluid and hence,
the rate of heat transfer increases. The exchanger has one shell and seven tubes with two
transverse baffles in the shell. The exchanger is mounted on a PVC base plate which
incorporates four holes, which locate it on four studs at the left hand end of the service unit.
The PVC base plate is secured to the service unit using thumb nuts. In normal operation the hot
fluid from the hot water circulator enters the header at one end of the shell and passes through
the bundle of stainless steel tubes. The cold fluid from the cold water supply passes through the
cylindrical shell. This arrangement minimizes heat loss from the exchanger without the need for
additional insulation and allows the construction of the exchanger to be viewed.
PROCEDURE:
 Fix the four thermometers in position.
 Start the flow on hot water side. Similarly start the flow on cold water side.
 Switch on the geyser.
 Adjust the flow rate on water side. Keep the flow rate same till steady state is achieved
(i.e. temperature readings do not change with time).
 Note the temperatures and measure the flow rates.
 4th and 5th steps are repeated for different sets of flow rate.
CALCULATIONS :
Mass flow rate (qm), kg/s = Volume flow rate (qv) x Density of fluid (ρ)
Heat power (Q), W = Mass flow rate (qm) x specific heat (cp) x (ΔT)
Therefore:
Heat power emitted from hot fluid Qh= qmh. Cph (T1 - T2)
Heat power absorbed by cold fluid Qc= qmc. Cpc (T4 - T3)
Heat power lost (or gained) Qf= Qh- Qc
Overall Efficiency η = Qc/Qh * 100 %
Theoretically Qh and Qc should be equal. In practice these differ due to heat losses or gains to/
from the environment.
Sample calculation :
Mass flow rate of hot water= 49.457 *10-3 kg/s
Inlet temperature of hot fluid = 40°C
Outlet temperature of hot fluid = 36°C
Heat lost by hot fluid =m*Cph*∆T

Qh=49.457*10-3*4180.5*4= 0.827*103J/s
Mass flow rate of cold water = 100.128* 10-3 kg/s

∆T= 1°C
Cpc=4187 J/kg.K
Qc=100.128*10-3*4178*1 =0.418*10 3J/s
Ƞ= Qc/Qh = .418/.827 = 0.505

RESULT AND DISCUSSION:
HOT WATER COLD WATER ƞ

Mass flow Inlet Outlet Mass flow Inlet Outlet
Qh Qc
rate(*10-3) temp. temp. rate(*10-3) temp. temp.
(J/s) (J/s)
(°C) (°C) (°C) (°C)
49.457 40 36 827.01 100.128 27 28 418.23 0.505
40.9972 42 37 856.94 107.470 27 28 449.00 0.524
44.657 41 36.5 840.10 90.90 27 28 379.78 0.452
From the results obtained we can see that the effectiveness of heat exchanger obtained shows
variation with change in flow rates. This can be observed that for best heat exchanger, we must
have optimum condition of flow rates.
Possible sources of error are :
 leakage in apparatus
 improper working of thermometer
 blockage in thermo-wells
 wrong measurement of flow rate due to lack of proper measuring instruments.
NOMENCLATURE:
Ƞ : Efficiency of heat exchanger
Qf: Heat transferred between fluids
Cph : Heat capacity of hot fluid
Cpc: Heat capacity of cold fluid
qmh: mass flow rate of hot fluid
qmc: mass flow rate of cold fluid

Heat Exchanger

Uploaded by

Copyright:

Available Formats

Heat Exchanger

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Heat Exchanger

Uploaded by

Copyright:

Available Formats

EXPERIMENT NO.

 THE THERMAL ANALYSIS-

Heat lost by hot fluid =mCph∆T

Mass flow rate of cold water = 100.128* 10-3 kg/s

Ƞ= Qc/Qh = .418/.827 = 0.505

HOT WATER COLD WATER ƞ

49.457 40 36 827.01 100.128 27 28 418.23 0.505

40.9972 42 37 856.94 107.470 27 28 449.00 0.524

44.657 41 36.5 840.10 90.90 27 28 379.78 0.452

Possible sources of error are :

You might also like