tInactivityTimer , dlMaxRetxThreshold , ulMaxRetxThreshold , qOffsetcellEUtran , qRxLevMin Check these counters on target cell , Reduce no.

rget cell , Reduce no. of HO by physical opti or features (UE Level Oscillating Handover Minimization & Automated
SchedulingAlgorithm , crsGain , tPollRetransmitUl (DRB & SRB) , tPollRetransmitDl (DRB & SRB) Mobility Optimization)
numInitialAccessAndIncomingHo (system constant) , SpdcchLaGinrMargin (system constant) MP capacity of DUS is higher than DUL , to increase MP capacity DUL can be replaced by DUS
pmHoPrepRejInHighLoad (MP load control) ulInterferenceForgettingFactor (system constant) , deltaPsdRs2Tx (system constant ) Physical changes (Tilt , Azimuth , height of antenna) to offload traffic from target cell
Neighbor cell load issue pmHoPrepRejInOverload (procedure latency supervision) noOfPucchCqiUsers , noOfPucchSrUsers , pdcchCfiMode Offload Target cell Load by changing Layering strategy, Idle mode cellreselection, connected mode mobility & Load balancing parameters
pmHoPrepRejInLicMob Audit licenseState,featurestate,servicestate & other paramter related to Intra freq HO feature

VoLTE_OnePager_Mobility_CounterBased Neighbor cell License issue

pmHoPrepRejInLicMultiErab
pmHoPrepRejInLicRlcUm
Audit licenseState,featurestate,servicestate & other paramter related to MultiErabsPerUser feature
Audit licenseState,featurestate,servicestate & other paramter related to RlcUm feature
capacityUnitConnectedUsers Check "licenseCapacityConnectedUsers" of Target cell
pmHoPrepRejInLicConnUsers gracePeriodTimeLeft Also Graceperiod should be noticed to exceed the licensed capacity limits for a limited periodof timeOffload traffic from target cell
dlTransNwBandwidth , ulTransNwBandwidth Audit UE Admission Control,Bearers (SRB & DRB) Admission Control,Transport Network Admission Control & Emergency call prioritization
Admission reject pmHoPrepRejInBearerAdmissionRej zzzTemp20 , zzzTemp21 , pmRrcConnMax , pmRrcConnLevSum Physical changes (Tilt , Azimuth , height of antenna) to offload traffic from target cell
pmHoPrepAttLTEIntraF Check configuration issues (especially after new site is integrated)
pmHoPrepSuccLTEIntraF (check MO ExternalEUtranCellFDD,EUtranCellRelation,TermPointToENB,TermPointToMme)
pmHoPrepAttLTEInterF Configuration issue (also check config para ex. Activeplmnlist,PCI , TAC , EutranFrequencyRef , IP address of TermPointToENB & MME)
Handover Preparation Failure pmHoPrepSuccLTEInterF
Configuration issues ensure proper configuration , especially for all new site which are integrated recently
Ensure the eNodeB structure of the restart, MP Baseband or RRU
eNodeB Cause
Auto Restart lh all llog -l (do complete eNB health checkup)
pmCellDowntimeAuto
Baseband Startup issue Baseband Trace can be used , te enable all bbmcBbOmMeSwU
Cell Down Auto pmCellDownLockAuto
Transport Cause S1 issues pmErabRelAbnormalEnbActTnFail check for alarms like Service Unavailable(S1 connection failure)
Availability Cell down EPC Cause check for alarms like Service Unavailable(S1 connection failure) , Ip packet loss "above" SGW
pmCellDowntimeMan manually locked during network configuration issues ((eg. adding/changing/removing hardware)
Cell Down Manually pmCellDownLockMan Operation Cause manually locked during parameter change (eg. activate feature)
Equipment causes RRU Issue / Antenna Issue Check alarms , hardware status , reset eNB if required
Common alarm : "resource configuration disable" , RRU fault , link failure , Check current & history alarms & take necessary action according to type of Alarms
Other checks Check RRU status , Reset boards , Verify SW on node
HW/SW Cause S1 links down due to faulty interface board.
Alarms Check related alarms like Serviceunavailable (S1 connection failure,Hardware failure,GeneralHwError,GeneralSwError,Gigabit Ethernet Link Fault)
HW issues Check HW issues , alarms , improper cabling , connector issues , DUS Board error
SW package preparation failure will be high if there is SW package corrupt
MME pool If MME pool is different at source and target then HO-Preparation fail will be 100%, command "get . termpointmme" can be used to find out the MME pool IPs
PCI confliction or confusion Audit PCI of near by sites , also check if there is overshooting cell creating conflict , OSS PCI conflicting function
Indoor coverage issue (Small cell , PICO , DOT , Hetnet)
pmBadCovEvalReport Physical changes (Tilt , Azimuth , height of antenna)
pmRadioTbsPwrRestricted maximumTransmissionPower , partOfSectorPower Audit cell reselection parameters , Tune DL power related parameters (as mentioned beside)
Coverage issues pmBadCovSearchEvalReport confOutputPower , crsGain , pdschTypeBGain Check if there is scope of new site
maximumTransmissionPower , partOfSectorPower Tune related parameters (as mentioned beside) , Audit cell reselection parameters
Poor DL SINR (CQI) pmRadioUeRepCqiDistr , pmRadioUeRepCqiDistr2 confOutputPower , crsGain , pdschTypeBGain Physical optimization (Tilt , Azimuth , height of antenna) also Identify overshooting cells causing interference in DL
pmRadioRecInterferencePwr
pmRadioRecInterferencePwrPucch Check Power control parameters , Features like IRC & UL FSS can help to reduce UL interference.
pmRadioRecInterferencePwrPrb1~100 pZeroNominalPucch Check for Loose Connectors,Faulty Antenna(Tx & Rx antenna ports),VSWR alarms,Faulty TMA Connections/settings.
LTE Intra/Inter Frequency(HOSR) UL RSSI pmSinrPucchDistr , pmSinrPuschDistr pZeroNominalPusch External interference (cable tv , repeaters (due to power leak issues) , airport , police communication system etc..)
Alarms Alarm need to monitor , some alarms need to monitor are VswrOverThreshold , Serviceunavailable (S1 connection failure) , Gigabit Ethernet Link Fault
Configuration issues ensure proper configuration , especially for all new site which are integrated recently
Ensure the eNodeB structure of the restart, MP Baseband or RRU
eNodeB Cause
Auto Restart lh all llog -l (do complete eNB health checkup)
pmHoExeAttLTEIntraF
pmCellDowntimeAuto
pmHoExeSuccLTEIntraF Baseband Startup issue Baseband Trace can be used, to enable all bbmcBbOmMeSwU
Cell Down Auto pmCellDownLockAuto
pmHoExeAttLTEInterF
Transport Cause S1 issues pmErabRelAbnormalEnbActTnFail check for alarms like Service Unavailable(S1 connection failure)
Handover Execution Failure pmHoExeSuccLTEInterF
Cell down EPC Cause check for alarms like Service Unavailable(S1 connection failure) , Ip packet loss "above" SGW
pmCellDowntimeMan manually locked during network configuration issues ((eg. adding/changing/removing hardware)
HW issues & Alarms Cell Down Manually pmCellDownLockMan Operation Cause manually locked during parameter change (eg. activate feature)
pmRaAttCbra , pmRaSuccCbra , pmRaFailCbraMsg2Disc
Availability pmRaAttCfra , pmRaSuccCfra , pmRaFailCfraMsg2Disc
pmRaAllocCfra , pmRrcConnEstabAtt , pmRrcConnSucc Verify symtoms for sleeping cell
Sleeping Cell
Catch Trace(Baseband) trace from MSG1 to MSG5 , verify symtoms for sleeping cells
Power setting issue Check SectorEquipmentFunction:ConfiguredOutputPower & EutrancellFDD:partOfSectorPower
Configuration issue
Non-access issue Idle mode parameter issue Check EutrancellFDD MO cell selection and reselection parameters & 3G&2G cell reselection parameter/feature
Operation issues Cell Barred Check Cell Barred , acBarring for different scenarios
HW issues Check HW issues , alarms , improper cabling , connector issues , DUS Board error
preambleInitialReceivedTargetPower , cellrange
pmHoPrepSuccLteInterFQci powerRampingStep (Hardcoded) , preambleTransMax (Hardcoded) Tune RACH related parameters , also check symptoms for sleeping cell (mentioned below)
pmHoPrepAttLteIntraFQci Target cell RACH issue pmRaAttCfra , pmRaSuccCfra numberOfRA-Preambles (Hardcoded) Improve RF conditions (by parameters or physical optimization (tilt/azimuth/antenna height))
PREPARTION pmHoPrepRejInLicRlcUm EUtranCellRelation
Wrong neighbour CM cross-check ExternalEUtranCellFDD
Intra LTE cellIndividualOffsetEUtran ; a3offset ; hysteresisA3 ; timeToTriggerA3 , isHoAllowed , filterCoefficientEUtraRsrp , sMeasure.
Tune HO related parameters
Inter freq LTE a5Threshold1RSRP ; a5Threshold2RSRP ; hysteresisA5 ; timeToTriggerA5 , a2ThresholdRsrpPrim , timeToTriggerA2Prim , hysteresisA2Prim
Other imp checks Transport nw Issue TN Outage / Flicker Alarm , S1 or X2 interfaces DOWN (Transport Resource Unavailable) , Also check 3G collocated nodeb in term of SCTP LOSS , TN & SGW alarm check
EPC Cause MME configuration Missing / Incorrect TA list , MME configuration check
Highload RRC Connected user Traffic volume related counters
pmHoExeAttLteInterFLb , pmHoExeSuccLteInterFLb qciSubscriptionQuanta , lbThreshold , lbCeiling , hysteresisA5
Inter-f load balancing pmHoPrepAttLteInterFLb , pmHoPrepSuccLteInterFLb cellSubscriptionCapacity , a5Threshold1Rsrp , a5Threshold2Rsrp configuration Check eNodeB configuration
Connected mode priority Check eNodeB configuration
a2ThresholdRsrpPrim ,hysteresisA2Prim , timeToTriggerA2Prim ,
LTE Inter Frequency Session Continuity pmUeCtxtRelSCEutra a5B2MobilityTimer Coverage of target freq is poor , Tune parameters below to control SC
Session Continuity
Inter RAT Session continuity pmUeCtxtRelSCWcdma a2ThresholdRsrpPrim ,hysteresisA2Prim , timeToTriggerA2Prim , a5B2MobilityTimer Coverage of target RAT is poor , Tune parameters below to control SC
a1a2SearchThresholdRsrp , hysteresisA1A2SearchRsrp , searchEffortTime
pmCriticalBorderEvalReport timeToTriggerA1Search , timeToTriggerA2Search , a2CriticalThresholdRsrp
MCPC pmBadCovSearchEvalReport hysteresisA2CriticalRsrp , timeToTriggerA2Critical , zzzTemporary13 , zzzTemporary14 Tune parameters according to number of carriers in LTE
Target Cell Availibility target site is disabled / sector down / software package corrupt
b2Threshold1Rsrp , b2Threshold2RscpUtra ,
hysteresisB2 , timeToTriggerB2 , triggerQuantityB2 configuration issue Frequency relation (UtranFreqRelation) , neighbor relation (ExternalUtrancell)
pmHoPrepAtt a2ThresholdRsrpPrim ,hysteresisA2Prim EPC Cause Check EPC configuration
Handover Preparation Failure pmHoPrepSucc timeToTriggerA2Prim , a5B2MobilityTimer
MOBILITY Target cell load Check load & admission control parameter of legacy network
Tune parameters Audit beside mentioned parameters for IRAT HO

IRAT IRAT Handover(HOSR) HW issues Check HW issues , alarms , improper cabling , connector issues , VSWR
b2Threshold1Rsrp , b2Threshold2RscpUtra ,
Legend hysteresisB2 , timeToTriggerB2 , triggerQuantityB2 Poor Coverage Check target cell Coverage area (legacy network)
pmHoExeAtt a2ThresholdRsrpPrim ,hysteresisA2Prim Target cell High UL interference Check interference issues in target cell
RF/SIP Signature Handover Execution Failure pmHoExeSucc timeToTriggerA2Prim , a5B2MobilityTimer
Wrong neighbour Check configuration parameter of neighbor cell

Counters HW issues Check HW issues , alarms , improper cabling , connector issues , VSWR

pmHoExeOutSuccQci
Parameter EXECUTION pmHoExeOutAttQci

Action plan SRVCC service is not subscribed for this UE in HSS ,that is HSS lacking of STN-SR
Add STN-SR value in ISM (IMS Subscription Manager)
Check for any recent UMTS RNC rehomes & make sure new UMTS Freq is defined as Freq relation under UtranFrequencyRelation MO
pmHoPrepAttSrvcc Verify UMTS information(LAC,RNCID, UARFCN..) under ExternalUtranCellFDD matches with information in UMTS network
PRE-Fail pmHoPrepSuccSrvcc Check "srvcccapability" setting for UMTS neighbors, should be set to 1(CS_ONLY_SUPPORTED)
featureStateSRVCCtoUTRAN Optimize A2/B2 thresholds specific to QCI1(a2ThresholdRsrpPrimOffset,b2Threshold1RsrpUtraOffset,b2Threshold2RscpUtraOffset) if triggerQuantity is RSRP to trigger SRVCC in
SRVCC Enabled licenseStateSRVCCtoUTRAN optimal conditions on LTE & UMTS for successful handover. (If triggerQuantity is RSRQ optimize the same parameters mentioned above related to RSRQ).
pmHoExeAtt Check which particular cell SRVCC is being attempted & see if that UMTS cell has any performance issues or congestion.
Exec-Fail pmHoExeSucc Check VoicePrio & align with connectedModeMobility settings
SRVCC Recommend SRVCC Activation on site with
SRVCC not Enabled high inter site distance/LTE Border Site.)
Check VoicePrio & ConnectedModePriority
Check VoicePrio & ConnectedModePriority settings are correctly aligned & as per strategy.