Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 2K views

    General Dimensional Tolerance For Parts Formed by Press Working From Sheet Metal

    Uploaded by

    Ricardo F.A.
    This document provides dimensional tolerances for parts formed from sheet metal by pressing or bending. It defines three tolerance classes - A, B, and C - with allowed tolerances that increase from A to C. Table 1 lists the standard tolerances for punching, bending, and dimensional ranges from less than 10mm to over 2000mm. Table 2 provides standard tolerances for bending angles in degrees. Class A angle tolerances are not defined. Tolerances exclude dimensions that do not require accuracy and can be indicated collectively.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    General Dimensional Tolerance For Parts Formed by Press Working From Sheet Metal

    Uploaded by

    Ricardo F.A.
    2K views2 pages
    This document provides dimensional tolerances for parts formed from sheet metal by pressing or bending. It defines three tolerance classes - A, B, and C - with allowed tolerances that increase from A to C. Table 1 lists the standard tolerances for punching, bending, and dimensional ranges from less than 10mm to over 2000mm. Table 2 provides standard tolerances for bending angles in degrees. Class A angle tolerances are not defined. Tolerances exclude dimensions that do not require accuracy and can be indicated collectively.

    Original Description:

    vA LA MATEMATICA

    Original Title

    E_D0016_2010-N

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides dimensional tolerances for parts formed from sheet metal by pressing or bending. It defines three tolerance classes - A, B, and C - with allowed tolerances that increase from A to C. Table 1 lists the standard tolerances for punching, bending, and dimensional ranges from less than 10mm to over 2000mm. Table 2 provides standard tolerances for bending angles in degrees. Class A angle tolerances are not defined. Tolerances exclude dimensions that do not require accuracy and can be indicated collectively.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    2K views2 pages

    General Dimensional Tolerance For Parts Formed by Press Working From Sheet Metal

    Uploaded by

    Ricardo F.A.
    This document provides dimensional tolerances for parts formed from sheet metal by pressing or bending. It defines three tolerance classes - A, B, and C - with allowed tolerances that increase from A to C. Table 1 lists the standard tolerances for punching, bending, and dimensional ranges from less than 10mm to over 2000mm. Table 2 provides standard tolerances for bending angles in degrees. Class A angle tolerances are not defined. Tolerances exclude dimensions that do not require accuracy and can be indicated collectively.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    D0016 [2010-N]

    Nissan Engineering Standard

    General dimensional tolerance for parts formed by press


    NES working from sheet metal
    1. SCOPE
    This Standard specifies the standard dimensional tolerances for punching or bending stamped metal sheet
    parts. If tolerances are indicated, they should conform to NES D 0030 (Special Tolerances for Stamped
    Metal Parts).

    Remarks: 1. For dimensions not requiring specific accuracy for a part to perform its function, the standard
    dimensional tolerances shall not apply to individual dimensions but shall be indicated
    collectively.
    2. Tolerances should be indicated in one of the following two ways (1) or (2) on drawings or
    documents:
    (1) Select the tolerance from the value table for each dimensional classification.
    (2) Standard number and class. Example: NES D 0016-99-A
    No. for this Standard
    Class A according to NES D 0016

    When general dimensional tolerances of blanking and those of bending and drawing are specified by different
    classes, it shall be specified clearly.
    Ex: General dimensional tolerances of blanking NES D 0016-99-B
    General dimensional tolerances of bending and drawing NES D 0016-99-C
    2. CLASS
    The standard tolerances are divided into three classes: A, B, and C.

    3. STANDARD TOLERANCE
    The standard dimensional tolerances for punching or bending parts are shown in Table 1, and the standard
    bending angle tolerances are shown in Table 2.

    Table 1 Standard punching and bending tolerances


    Unit: mm
    Class
    Class A Class B Class C
    Dimension range
    d ≤ 10 ±0.08 ±0.18 ±0.45
    10 < d ≤ 18 ±0.09 ±0.22 ±0.55
    18 < d ≤ 30 ±0.1 ±0.25 ±0.60
    30 < d ≤ 50 ±0.12 ±0.30 ±0.80
    50 < d ≤ 120 ±0.18 ±0.45 ±1.10
    120 < d ≤ 315 ±0.25 ±0.60 ±1.60
    315 < d ≤ 1,000 ±0.45 ±1.1 ±2.8
    1,000 < d ≤ 2,000 ±0.8 ±1.8 ±4.5
    2,000 < d ±0.9 ±2.2 ±5.5

    Table 2 Standard bending angle tolerance


    Unit: degree
    Class
    Class B, Class C
    Type
    Right angle bend ±1
    Other bends ±1.5
    Remarks: 1. The standard bending angle tolerance for class A is not defined.
    2. The above excludes the case when the bend line is curving

    References: JIS B 0405-01 General tolerances – part 1: Tolerances for linear and angular dimensions without
    individual tolerance indications
    JIS B 0408-01 General dimensional tolerances for parts formed by press working from sheet metal

    Nissan Internal
    – 1/2 –
    D0016 [2010-N]
    NES D 0030-10 Special Dimensional Tolerances for Stamped Parts
    ANNEX
    1. Purpose of revision
    It was concluded by the council that JIS is not practical and change was not applied same as the last revision.

    2. Scope
    (1) Stamping in the range of application of this standard specifies tolerance for shape, punching of holes, bending,
    bending angle. Draw diameter, draw shape (emboss, bead, etc.), parting (gap between panels) are excluded.
    Remark 1 shows applying method and remark 2 shows indication method of general dimension tolerance.
    (2) When there are dimension indications from coordinates in the design drawing (parts drawing), follow dimension
    range of 50 < d ≤ 120 on the Table 1. (Refer to the below drawing.)

    Square hole

    In case of dimension indication for the


    square holes in the drawing at left,
    the above dimension ranges are applied
    by using dimensions in ( ).

    Nissan Internal
    – 1/2 –

    You might also like