HUBBELL ELECTRICAL PRODUCTS

A Division of HUBBELL INCORPORATED (Delaware)

3940 Dr. Martin Luther King Drive
St. Louis, Missouri 63113 USA

INSTALLATION, OPERATION, & MAINTENANCE DATA SHEET

For QUANTUM  ENCLOSURES (EXB-N34 & EXBLT-N4 Junction Boxes)

For use in Class I, Groups B, C & D, Type 3 & 4, Class II, Groups E, F & G and Class III Hazardous Locations,
as defined by the Canadian Electrical Code and the National Electrical Code.

INSTALLATION INSTRUCTIONS

This junction box must be installed by trained, qualified and competent personnel. Installation must comply
with local, state and national regulations, as well as safety practices for this type of equipment.

WARNING: Electrical power must be OFF during installation. Disconnect primary power source
and lock out.

The mounting location must be flat and provide proper clearance, rigidity and strength to support the
enclosure and all contained devices. (Refer to Figures 1 & 2)
Larger enclosures are equipped with factory installed hinges. Enclosure should be mounted with
hinges on the left. Do not mount the enclosure with hinges on the top or bottom side. (See Figure 3)
Securely fasten the enclosure to the mounting location, using ½” diameter steel mounting bolts and
washers, or washer head bolts. Install sealing fittings and conduit using an approved electrical conducting
type lubricant on the threads. The conduit thread connections must be tapered pipe thread conforming to
ANSI/ASME B1.20.1. A minimum of five (5) full threads engagement is required for all conduit connections.
Conduit sealing fittings, approved for the specific hazardous location where the enclosure is used, must be
installed within 18” of the enclosure. All unused conduit openings must be plugged using a close-up plug
approved for the specific hazardous location where the enclosure is used. Plugs must be tightly installed
with a minimum engagement of five (5) full threads.

IMPORTANT: Install only U.L. listed and CSA certified auxiliary control devices for hazardous locations
(Long and Extra-Long style only). Refer to individual operator installation sheet for installation details. The
minimum wall thickness of counter-bore (where required) and operator spacing are to be determined from
the dimensional chart on Pages 2 & 3.

NOTE: If installing a breather and/or drain, make certain they are suitable for the specific hazardous
location where they are to be used. Also, provide a protective device to shield the breather and drain
during hose-down operations.
Inspect and clean the machined flange flame joint surfaces of both the cover and box. Surfaces
must be smooth, free of nicks, scratches, dirt or any foreign particle build-up that would prevent a proper
seal. Surfaces must seat fully against each other to provide a proper explosion-proof joint. Clean surfaces
by wiping with a clean, lint-free cloth.
Apply a light coat of Killark “LUBG” lubricant to flange surfaces and close the cover. Install and
tighten all cover bolts to 30 ft. lbs. Make certain no cover bolts are omitted. Use only those bolts supplied
with the enclosure. Check the bolted joint with a .0015” thick feeler gauge. The gauge must not enter the
joint more than 1/8” at any point.

NOTE: Missing bolts or an improper joint can result in an explosion, creating a potential for physical
injury or property damage.

P/N 00911572 FORM NO. K0983 R04/18 ECO-2-018-18 page 1 of 4

 ENCLOSURE INTERNAL DIMENSIONS EXTERNAL OPERATOR AREA Min. Max Max Encl. ENCLOSURE
MOUNTING DIMENSIONS CONDUIT AREA
CATALOG PAN INTERNAL VOLUME DIMENSIONS SPECFICATIONS Thk. at Dia. of # of Wgt. CATALOG
NUMBER A B C D E* F* G H I J K L M N O P Q R S T U V W X Y Z C-bore C-bore Oper. (lbs) NUMBER

page 2 of 4
EXB-664 N34 5 5 3 3 5.73 5.73 4.31 10.32 10.32 6.09 N/A 4 7.88 N/A 0.19 1.18 2.81 2.44 4.88 2.75 2.81 2.44 4.88 2.5 5 5 ** 2.5 4 18 EXB-664 N34
EXB-684 N34 5 7 3 5 5.75 7.75 4.25 10.25 12.25 6.12 N/A 6 7.88 N/A 0.19 1.18 2.81 3.44 6.88 2.75 2.81 2.44 4.88 2.5 7 5 ** 2.5 6 20 EXB-684 N34
EXB-6124 N34 5 11 3 9 5.75 11.75 4.44 10.69 16.69 7 3.82 7.82 7.88 7.82 0.19 1.18 2.81 5 10 2.75 2.81 2.44 4.88 2.5 11 5 0.81 2.5 8 32 EXB-6124 N34
EXB-886 N34 7 7 5 5 7.59 7.59 6.06 12.32 12.32 8.09 N/A 6 9.88 N/A 0.19 1.18 4.81 3.44 6.88 3.75 4.81 3.44 6.88 2.5 7 7 ** 2.5 9 30 EXB-886 N34
EXB-8104 N34 7 9 5 7 7.73 9.73 4.06 12.32 14.32 6.32 N/A 8 9.88 N/A 0.19 1.18 2.81 4.44 8.88 2.75 2.81 3.44 6.88 2.5 9 7 ** 2.5 12 34 EXB-8104 N34
EXB-8106 N34 7 9 5 7 7.59 9.59 6.06 12.32 14.32 8.32 N/A 8 9.88 N/A 0.19 1.18 4.18 4.44 8.88 3.45 4.81 3.44 6.88 2.5 9 7 ** 2.5 12 38 EXB-8106 N34
EXB-8126 N34 7 11 5 9 8 12 6.38 13.25 17.25 8.7 3.82 7.82 10.38 14.38 0.19 1.78 3.75 5 10 3.66 3.75 3 6 2.5 11 7 0.81 2.5 12 47 EXB-8126 N34
EXB-8128 N34 7 11 5 9 8 12 8.38 13.25 17.25 10.7 3.82 7.82 10.38 14.38 0.19 1.78 5.75 5 10 4.66 5.75 3 6 2.5 11 7 0.81 2.5 12 67 EXB-8128 N34
EXB-10106 N34 9 9 7 7 10 10 6.2 15.25 15.25 8.9 4.94 4.94 12.94 12.94 0.25 1.91 3.75 4 8 3.79 3.75 4 8 2.5 9 9 1.06 2.5 9 66 EXB-10106 N34
EXB-10108 N34 9 9 7 7 10 10 8.2 15.25 15.25 10.9 4.94 4.94 12.94 12.94 0.25 1.91 5.75 4 8 4.79 5.75 4 8 2.5 9 9 1.06 2.5 9 72 EXB-10108 N34
EXB-10146 N34 9 13 7 11 10 14 6.2 15.25 19.25 8.9 4.94 8.94 12.94 16.94 0.25 1.91 3.75 6 12 3.79 3.75 4 8 2.5 13 9 1.06 2.5 15 82 EXB-10146 N34
EXB-10148 N34 9 13 7 11 10 14 8.2 15.25 19.25 10.9 4.94 8.94 12.94 16.94 0.25 1.91 5.75 6 12 4.79 5.75 4 8 2.5 13 9 1.06 2.5 15 89 EXB-10148 N34
EXB-12126 N34 10.5 10.5 9 9 11.5 11.5 6 16.38 16.38 8.69 6.94 6.94 14.94 14.94 0.25 1.88 3.81 4.94 9.88 4 3.81 4.94 9.88 2.5 10 10 ** 2.5 16 75 EXB-12126 N34
EXB-12128 N34 10.5 10.5 9 9 11.37 11.37 8 16.38 16.38 10.69 6.94 6.94 14.94 14.94 0.25 1.88 5.81 4.94 9.88 5 5.81 4.94 9.88 2.5 10 10 ** 2.5 16 83 EXB-12128 N34
EXB-12186 N34 10 16 9 15 11.5 17.5 6 16.38 22.38 9.06 6.94 12.88 14.94 20.88 0.25 2.06 3.13 7.94 15.88 3.88 3.75 4.94 9.88 2.5 16 10 ** 2.5 28 110 EXB-12186 N34
EXB-12188 N34 10 16 9 15 11.37 17.37 8 16.38 22.38 11.06 6.94 12.88 14.94 20.88 0.25 2.06 5.13 7.94 15.88 4.88 5.75 4.94 9.88 2.5 16 10 ** 2.5 28 120 EXB-12188 N34
EXB-12246 N34 10.3 22.3 9 21 11.5 23.5 6 16.38 28.38 9.32 6.94 18.88 14.94 26.88 0.25 2.13 3.13 10.94 21.88 3.94 3.81 4.94 9.88 2.5 22.25 10.25 ** 2.5 36 145 EXB-12246 N34
EXB-12248 N34 10.3 22.3 9 21 11.37 23.37 8 16.38 28.38 11.32 6.94 18.88 14.94 26.88 0.25 2.13 5.13 10.94 21.88 4.94 5.81 4.94 9.88 2.5 22.25 10.25 ** 2.5 36 160 EXB-12248 N34
EXB-122412 N34 10.3 22.3 9 21 11.37 23.37 12.16 16.38 28.38 15.18 6.94 18.88 14.94 26.88 0.25 2.13 9.28 10.94 21.88 7.12 9.28 4.94 9.88 2.5 22.25 10.25 ** 2.5 36 225 EXB-122412 N34
EXB-12368 N34 11 35 9 33 12 36 8.12 17.25 41.25 11.4 7 31 15 39 0.25 2.09 5.75 17 34 4.97 5.75 10 20 2.5 35 11 1.38 2.5 56 231 EXB-12368 N34
EXB-123610 N34 11 35 9 33 12 36 10.12 17.25 41.25 13.4 7 31 15 39 0.25 2.09 7.75 17 34 5.97 7.75 5 10 2.5 35 11 1.38 2.5 56 245 EXB-123610 N34
EXB-14146 N34 13 13 11 11 14 14 6.2 19.25 19.25 9.4 9 9 17 17 0.25 2.09 3.75 6 12 3.97 3.75 6 12 2.5 13 13 1.38 2.5 25 121 EXB-14146 N34
EXB-14148 N34 13 13 11 11 14 14 8.2 19.25 19.25 11.4 9 9 17 17 0.25 2.09 5.75 6 12 4.97 5.75 12 24 2.5 13 13 1.38 2.5 25 136 EXB-14148 N34
EXB-16166 N34 14 14 13 13 15.5 15.5 6 20.38 20.38 9.19 10.94 10.94 18.94 18.94 0.25 2.06 3.75 6.94 13.88 4.18 3.75 6.94 13.9 2.5 14 14 ** 2.5 36 127 EXB-16166 N34
EXB-16168 N34 14 14 13 13 15.37 15.37 8 20.38 20.38 11.19 10.94 10.94 18.94 18.94 0.25 2.06 5.75 6.94 13.88 5.18 5.75 6.94 13.9 2.5 14 14 ** 2.5 36 138 EXB-16168 N34
EXB-16248 N34 15 23 13 21 16 24 8.12 21.25 29.25 12 11.38 19.38 19.38 27.38 0.25 2.34 5.75 11 22 5.22 5.75 7 14 2.5 22 14 1.69 2.5 40 251 EXB-16248 N34
EXB-162410 N34 15 23 13 21 16 24 10.12 21.25 29.25 14 11.38 19.38 19.38 27.38 0.25 2.34 7.75 11 22 6.22 7.75 7 14 2.5 22 14 1.69 2.5 40 266 EXB-162410 N34
EXB-18186 N34 17 17 15 15 18 18 6.12 23.25 23.25 10 13.38 13.38 21.38 21.38 0.25 2.34 3.75 8 16 4.22 3.75 8 16 2.5 16 16 1.69 2.5 36 206 EXB-18186 N34
EXB-18188 N34 17 17 15 15 18 18 8.12 23.25 23.25 12 13.38 13.38 21.38 21.38 0.25 2.34 5.75 8 16 5.22 5.75 8 16 2.5 16 16 1.69 2.5 36 220 EXB-18188 N34
EXB-18248 N34 16.4 22.1 15 21 17.37 23.37 8 22.38 28.38 11.75 13 19 21 27 0.25 2.32 4.88 10.94 21.88 5 5.56 7.94 15.9 2.5 22 16 ** 2.5 63 240 EXB-18248 N34
EXB-182410 N34 16.4 22.1 15 21 17.23 23.23 10 22.38 28.38 13.75 13 19 21 27 0.25 2.32 6.88 10.94 21.88 6 8.56 7.94 15.9 2.5 22 16 ** 2.5 63 260 EXB-182410 N34
EXB-18308 N34 16 29 15 28 17.88 30.88 8.13 22.63 35.63 12.44 13.25 26.5 21.25 34.5 0.25 3.32 5.54 14.5 29 6.09 6.2 7.94 15.9 2.5 29 16 ** 2.5 0.91 330 EXB-18308 N34

P/N 00911572 FORM NO. K0983 R04/18 ECO-2-018-18

EXB-18368 N34 16 34 15 33 17.37 35.37 8 22.38 40.38 12.38 13.25 31.5 21.25 39.5 0.25 2.5 4.88 16.94 33.88 5.18 6.06 7.94 15.9 2.5 34 16 ** 2.5 78 380 EXB-18368 N34
EXB-183610 N34 16 34 15 33 17.23 35.23 10 22.38 40.38 14.38 13.25 31.5 21.25 39.5 0.25 2.5 6.88 16.94 33.88 6.18 8.06 7.94 15.9 2.5 34 16 ** 2.5 78 405 EXB-183610 N34
EXB-203611 N34 18.8 34.8 16.8 32.8 20.14 36.14 11.13 26.44 42.44 15.56 15.75 31.75 23.75 39.75 0.25 2.47 8.44 16.72 33.97 6.88 8.47 8.72 17.5 2.5 34.88 18.88 ** 2.5 91 540 EXB-203611 N34
EXB-24248 N34 22.3 22.3 21 21 23.37 23.37 8.06 28.38 28.38 12.19 19.5 19.5 27.5 27.5 0.25 2.88 5.5 10.88 21.88 5.88 5.5 10.94 21.9 2.5 22 22 ** 2.5 81 330 EXB-24248 N34
EXB-242410 N34 22.3 22.3 21 21 23.23 23.23 10.06 28.38 28.38 14.19 19.5 19.5 27.5 27.5 0.25 2.88 7.5 10.88 21.88 6.88 7.5 10.94 21.9 2.5 22 22 ** 2.5 81 350 EXB-242410 N34
EXB-24308 N34 23 29 21 27 24 30 8.06 29.25 35.25 12.4 19.56 25.56 27.56 33.56 0.25 2.47 5.75 14 28 5.35 5.75 11 22 3 28 22 1.94 2.5 63 422 EXB-24308 N34
EXB-24368 N34 23 35 21 33 24 36 8.12 29.25 41.25 12.4 19.56 31.56 27.56 39.56 0.25 2.47 5.75 17 34 5.35 5.75 11 22 3 34 22 1.94 2.5 77 506 EXB-24368 N34
EXB-243610 N34 23 35 21 33 24 36 10.12 29.25 41.25 14.4 19.56 31.56 27.56 39.56 0.25 2.47 7.75 17 34 6.35 7.75 11 22 3 34 22 1.94 2.5 77 531 EXB-243610 N34
* Dimensions at bottom of box ** Spotface 1/16" Deep *** Center pan holes on EXB-1236, EXB-1824, EXB-2036, EXB-2436
ENCLOSURE INTERNAL DIMENSIONS EXTERNAL OPERATOR AREA Min. Max Max Encl. ENCLOSURE
MOUNTING DIMENSIONS CONDUIT AREA
CATALOG PAN INTERNAL VOLUME DIMENSIONS SPECFICATIONS Thk. at Dia. of # of Wgt. CATALOG
NUMBER A B C D E* F* E H I J K L M N O P Q R S T U V W X Y Z C-bore C-bore Oper. (lbs) NUMBER
EXBLT-664 N4 5 5 3 3 5.73 5.73 4.00 10.31 10.31 5.94 N/A 4.00 7.88 N/A 0.19 1.18 2.81 2.44 4.88 2.75 2.81 2.44 4.88 2.5 5 5 N/A N/A 4 17 EXBLT-664 N4
EXBLT-684 N4 5 7 3 5 5.75 7.75 4.00 10.25 12.25 5.94 N/A 4.00 7.88 N/A 0.19 1.18 2.81 3.44 6.88 2.75 2.81 2.44 4.88 2.5 7 5 N/A N/A 6 20 EXBLT-684 N4
EXBLT-686 N4 5 7 3 5 5.75 7.75 6.00 10.25 12.25 7.94 N/A 4.00 7.88 N/A 0.19 1.18 4.18 3.44 6.88 3.75 4.81 2.44 4.88 2.5 7 5 N/A N/A 6 23 EXBLT-686 N4
EXBLT-6124 N4 5 11 3 9 5.75 11.75 4.00 10.68 16.68 5.88 N/A 7.82 7.88 N/A 0.19 1.18 2.81 5 10 2.75 2.81 2.44 4.88 2.5 11 5 N/A N/A 8 29 EXBLT-6124 N4
EXBLT-6126 N4 5 11 3 9 5.75 11.75 6.00 10.68 16.68 7.88 N/A 7.82 7.88 N/A 0.19 1.18 4.18 5 10 3.75 4.81 2.44 4.88 2.5 11 5 N/A N/A 8 32 EXBLT-6126 N4
EXBLT-886 N4 7 7 5 5 7.59 7.59 6.00 12.31 12.31 7.94 N/A 6.00 9.88 N/A 0.19 1.18 4.81 3.44 6.88 3.75 4.81 3.44 6.88 2.5 7 7 N/A N/A 9 27 EXBLT-886 N4
EXBLT-8104 N4 7 9 5 7 7.73 9.73 4.00 12.31 14.31 5.94 N/A 8.00 9.88 N/A 0.19 1.18 2.81 4.44 8.88 2.75 2.81 3.44 6.88 2.5 9 7 N/A N/A 12 28 EXBLT-8104 N4
EXBLT-8106 N4 7 9 5 7 7.59 9.59 6.00 12.31 14.31 7.94 N/A 8.00 9.88 N/A 0.19 1.18 4.18 4.44 8.88 3.45 4.81 3.44 6.88 2.5 9 7 N/A N/A 12 31 EXBLT-8106 N4
EXBLT-9116 N4 8 10 6 8 9 11 6.00 13.31 15.31 7.94 N/A 7.50 10.88 N/A 0.19 1.18 4.18 4.44 8.88 3.45 4.81 3.44 6.88 2.5 9 7 N/A N/A 12 40 EXBLT-9116 N4
EXBLT-8126 N4 7 11 5 9 8 12 6.00 13.25 17.25 8.01 3.82 7.82 10.38 14.38 0.19 1.78 3.75 5 10 3.66 3.75 3 6 2.5 11 7 N/A N/A 12 47 EXBLT-8126 N4
EXBLT-8128 N4 7 11 5 9 8 12 8.00 13.25 17.25 10.01 3.82 7.82 10.38 14.38 0.19 1.78 5.75 5 10 4.66 5.75 3 6 2.5 11 7 N/A N/A 12 52 EXBLT-8128 N4
EXBLT-10106 N4 9 9 7 7 10 10 6.00 15.25 15.25 8.19 4.94 4.94 12.94 12.94 0.25 1.91 3.75 4 8 3.79 3.75 4 8 2.5 9 9 N/A N/A 9 49 EXBLT-10106 N4
EXBLT-10108 N4 9 9 7 7 10 10 8.00 15.25 15.25 10.19 4.94 4.94 12.94 12.94 0.25 1.91 5.75 4 8 4.79 5.75 4 8 2.5 9 9 N/A N/A 9 54 EXBLT-10108 N4
EXBLT-10146 N4 9 13 7 11 10 14 6.00 15.25 19.25 8.19 4.94 8.94 12.94 16.94 0.25 1.91 3.75 6 12 3.79 3.75 4 8 2.5 13 9 N/A N/A 15 60 EXBLT-10146 N4
EXBLT-10148 N4 9 13 7 11 10 14 8.00 15.25 19.25 10.19 4.94 8.94 12.94 16.94 0.25 1.91 5.75 6 12 4.79 5.75 4 8 2.5 13 9 N/A N/A 15 65 EXBLT-10148 N4
EXBLT-12126 N4 10.5 10.5 9 9 11.5 11.5 6.00 16.37 16.37 8.19 6.94 6.94 14.94 14.94 0.25 1.88 3.81 4.94 9.88 4.00 3.81 4.94 9.88 2.5 10 10 N/A N/A 16 56 EXBLT-12126 N4
EXBLT-12128 N4 10.5 10.5 9 9 11.37 11.37 8.00 16.37 16.37 10.19 6.94 6.94 14.94 14.94 0.25 1.88 5.81 4.94 9.88 5.00 5.81 4.94 9.88 2.5 10 10 N/A N/A 16 61 EXBLT-12128 N4
P/N 00911572 FORM NO. K0983 R04/18 ECO-2-018-18 page 3 of 4
 MAINTENANCE INSTRUCTIONS
After installation, this junction box should be inspected at regular intervals. A visual inspection should ascertain that all cover
bolts are installed and still tight; that all conduit connections are intact and free of corrosion, and that the enclosure mounting
bolts are tight and in good condition.
If the enclosure must be opened for servicing, to check or replace internal devices and apparatus, the following procedures
should be followed.
WARNING: Before servicing the enclosure, be certain the electrical power is OFF. Disconnect the enclosure from primary power
source and lock out.
Remove all cover bolts. Clean and inspect. Replace any corroded, bent or otherwise damaged bolts with new, factory
authorized bolts obtained from an authorized Killark distributor.
Open enclosure. Do not use hammer, screwdriver or any prying tool to open cover, except as shown in Figure 4.
Inspect cover hinges. If hinges are damaged or do not function properly, contact a factory authorized service representative
for hinge replacement and installation.
Inspect machined, flame joint flange surfaces. Surfaces must be smooth, free of nicks, scratches, dirt or any foreign particle
build-up that would prevent a proper seal. Should surface be damaged contact factory. Never attempt to rework surfaces by
sanding, grinding, etc. Surfaces must seat fully against each other to provide a proper explosion-proof joint.
Inspect water exclusion gasket. If gasket is damaged, do not attempt field replacement or repair.
Contact a factory authorized representative for a replacement cover. When removing gasketed cover for replacement, do
not detach hinge body from cover (NOTE: Optional hinges on 664, 886, 8104 & 8106 enclosures must be removed from cover).
Remove cover and hinge body from enclosure by removing the hinge pins. (See Figure 5) The damaged gasket can be
removed from the cover and the cover without gasket can be safely used in Class I & II hazardous (classified) locations,
however, the enclosure may not be raintight or hosedown tight.
Clean flange surfaces by wiping with a clean, lint-free cloth. Apply a light coating of Killark “LUBG” lubricant to flange surfaces
and close cover. Install and tighten all cover bolts to 30 ft. lbs. Make certain no cover bolts are omitted. Use only factory
authorized bolts. Check the flame joint with a .0015” thick feeler gauge. The gauge must not enter the flame joint more than
1/8 inch at any point. Missing bolts or an improper flame joint can result in an explosion, creating a potential for physical injury
and property damage.

Technical information, advice and recommendations contained in these documents is based on information that Killark believes to be reliable.
All the information and advice contained in the documents is intended only for use by persons having been trained and possessing the requisite
skill and know-how and to be used by such persons only at their own discretion and risk. The nature of these instructions is informative only and
does not cover all of the details, variations or combinations in which this equipment may be used, its storage, delivery, installation, check out,
safe operation, and maintenance. Since conditions of use of the product are outside of the care, custody and control of Killark, the purchaser
should determine the suitability of the product for his intended use, and assumes all risk and liability whatsoever in connection therewith.

P/N 00911572 FORM NO. K0983 R04/18 ECO-2-018-18 page 4 of 4