SPRAY GUN

LPH(low pressure) - 50・80・101・200・300・400 series

W(general purpose) - 50・101・200・300・400 series
 ④Selection of spray gun model? ● General purpose spray guns are spray guns you have been

How to select the right spray gun Selection of low pressure spray gun and general purpose spray gun using up to now.
● Is air volume enough ?
● From the viewpoint of environmental protection, spray guns of
Air compressor supplies about 100 liters/min. per 0.75kW（1PS）.
① Size of workpiece? ③ Stage of painting and viscosity? high transfer efficiency and little overspray are becoming mainstream
Use an air compressor which supplies 20 to 30 % larger free air
Selection of small type and large type Selection of fluid nozzle orifice and air cap in the world. LPH low pressure spray guns can achieve high
2 delivery than air consumption of selected spray gun.
● Small parts, toys, small workpieces, car repairs … small type ● An excellent finish for a top coat requires finely atomized paint atomization with low pressure of 0.07MPa（0.7kgf/cm ）in air cap.
※As for details, refer to「Air Compressons」catalog.
（LPH-50, 80, 101, W-101） particles. You need to select a spray gun that can provide a high Low pressure spray guns reduce VOC emission to atmosphere
● Do you use air filters and air regulators ?
● Large parts, vehicles, buildings, line coating, large coating… air-to-paint ratio, especially for metallic paint. and contribute to improvement of working conditions at painting site.
Moisture and oil are big enemies to coating.
large type（LPH-200, W-200） Paint viscosity and selection of nozzle orifice A spray gun can achieve satisfactory performance at air pressure
Ultra small Small type Large type Small type center gravity Large type center gravity
● You need to select nozzle orifice according to paint viscosity. Series type 50 series 100 series 200 series cup type 300 series cup type 400 series specified in instruction manual of each spray gun.
② Amount or area to be painted? Generally select small nozzle orifice for low paint viscosity, and Low pressure spray gun LPH-50 LPH-101 LPH-200 LPH-300 LPH-400 Be sure to fit air filter and air regulator or air transformer near painter
Selection of type of feed（ gravity feed, suction feed, large nozzle orifice for high paint viscosity. General purpose spray gun W-101 W-200 W-300 W-400 and use clean air without moisture or oil at regulated pressure.
pressure feed ） ※In case of pressure feed type, even the small nozzle orifice can cover
● For small amount or painting with frequent color changes, use a relatively wide range from low to high viscosity. ［How to read model names］ Caution
gravity feed (G type) ● Paint viscosity［Ford cup #4（Anest Iwata NK-2）］ （Ex.）LPH - 101 -14 4 LVG P: Pressure feed
S: Suction feed
● Figures in this catalog are measured by our test paints.
● For small or medium painting operations with frequent color ◎ Low viscosity［ less than 18 sec.（15 sec.）］0.8∼1.5φmm Low pressure low air volume G: Gravity feed
1,（odd numbers）: General purpose
They will differ according to kinds of paints and painting conditions.
changes, use suction feed (S type) ◎ Medium viscosity［18∼26 sec.（15∼25sec.）］1.3∼2.0φmm Degree of atomization
2, 4（even numbers）: High atomization
Nozzle orifice（Ex.）14：φ1.4mm
● For painting large amount of the same color on a conveyor line, ◎ High viscosity［ 26∼33 sec.（25∼35sec.）］2.0∼2.5φmm 50：Ultra small type
101：Small type（Compact）
use pressure feed (P type) with paint tank or paint pump. Kind of gun body
200：Large type
LPH：Low pressure spray gun 300：Small type center gravity cup type
W：General purpose spray gun 400：Large type center gravity cup type

When you spray corrosive paints in a line painting with LPH-200 or W-200 pressure feed spray guns at high frequency,
The typical application is shown below. Refer also to application examples shown in specifications for each spray gun model. we prepare an optional fluid nozzle and fluid needle set made of hard-to-wear material. ◎ Most suitable ⃝ Suitable

Classification Low pressure spray gun General purpose spray gun

LPH -
Model name LPH-50 LPH-101 200 LPH-300 LPH-400 W-101 W-200 W-300 W-400
Spray gun
Last letters of model name 042G 062G 102G 122P 124LVG 144LVG 144LVS 164LVG 164LVS 122P 124LV 144LV 164LV 144LV 164LV 082P 102P 132P 152P 101S 101G 131S 131G 132S 132G 134S 134G 151S 151G 152S 152G 181S 181G 122P 151S 151G 152S 152G 182S 201S 201G 202S 202G 251S 251G 081G 101G 132G 122G 142G 162G 182G 251G

Nozzle orifice（φmm） 0.4 0.6 1.0 1.2 1.2  1.4  1.4 1. 6 1.6 1. 2 1.2 1.4 1.6 1.4 1.6 0.8 1.0 1.3 1.5 1.0 1.0 1.3 1.3 1.3 1.3 1.3 1.3 1.5 1.5 1.5 1.5 1.8 1.8 1.2 1.5 1.5 1.5 1.5 1.8 2.0 2.0 2.0 2.0 2.5 2.5 0.8 1.0 1.3 1.2 1.4 1.6 1.8 2.5

Middle coat ○ ◎ ○ ◎
Auto body Top coat ○ ◎ ○ ◎
Refinish, touch-ups ○ ○ ○ ○ ◎ ○ ◎ ○ ◎ ○ ○ ◎ ◎ ○ ○ ◎
Large busses and trucks Middle coat, top coat ○ ○ ○ ○ ○ ○ ○ ○ ◎ ◎  ○ ◎ ◎ 
Primer ○ ◎ ○ ○ ◎ ○ ○ ○ ◎ ◎ ○ ○ ○ ○
Classification of industries and processes

Spray putty ○ ○ ○ ○ ○ ○ ○

Sheet metal for
autos Middle coat（primer surfacer） ○ ○ ○ ○ ○ ○ ○ ○ ○ ◎ ◎ ○ ○ ○ ○ ○ ○ ○
（passenger cars）
Top coat（touch-ups∼block） ◎ ◎ ◎ ○ ◎ ○ ○ ◎ ○ ◎ ○ ○ ◎ ◎ ◎ ◎ ◎ ◎ ○ ○ ◎ ○ ○
Top coat（whole body） ◎ ○ ◎ ◎ ◎ ◎ ◎ ○ ◎ ◎ ◎ ◎ ◎ ◎ ○ ○ ◎ ◎ ○  ◎ ◎ ○ 
Middle coat ◎ ◎ ◎ ◎ ○ ○ ○ ○ ◎ ○ ○ ○ ○
Metal
Top coat ○ ○ ○ ◎ ◎ ◎ ○ ◎ ◎ ○ ○ ◎ ○ ○ ○ ○ ◎
Plastic
（small workpieces）
Top coat ○ ○ ○ ○ ◎ ◎ ◎ ◎

Woodwork,
Middle coat ◎ ◎ ○ ○  ○ ○ ○ ◎ ◎ ◎
furniture
Top coat ◎ ◎ ◎ ◎ ○ ○ ◎ ◎ ◎
Steel frame Anti-corrosion ○ ○ ○ ○ ◎ ◎ ◎ ◎
Less than 200 centipoises
Adhesives ※   ※   ※
Less than 1000 centipoises

Small

Size of workpieces Medium

Large

Low viscosity（less than 15 sec.）

Paint viscosity
（Ford Cup #4） Medium viscosity（18∼26 sec.）

High viscosity（26∼33 sec.）

Note 1）When you use high viscosity paints, refer to spray guns for high viscosity paints on page 14. Note 2）Adhesives shown by ※ marked models can be sprayed by pressure feed type.

3 4
 Features of low pressure spray guns
High transfer efficiency and little overspray

Speed of air flow ejected from spray guns is slower in low pressure spray guns than that of
conventional spray guns. “Air flow is slow”means that power is weak against air flow
direction. In other words, with less bounceback, paint particles easily reach the workpiece,
since atomizing air pressure is low.

Low pressure spray guns 　　　　　　 Conventional spray guns

LPH-101LV type low pressure Conventional spray gun

low air volume spray gun Atomizing air pressure: 0.3 MPa
Atomizing air pressure: 0.1 MPa Pressure in air cap: 0.23MPa
Pressure in air cap: 0.05MPa

Improvement of work environment

Although use of water-based paints is expanding, paints using organic solvents are still
mainstream. To improve painting environment, we need to reduce the overspray paint mists.
Low pressure spray guns with less overspray paint mists can lengthen maintenance cycle of
spraying booths and minimize dirtiness of painters’clothing by reducing paint overspray.
Less overspray means improvement of painting operation environment.

Paint consumption of
conventional spray gun

You can reduce paint consumption by 20～30% .

Paint consumption of low pressure spray gun

In addition to previous High Volume Low Pressure spray guns, we have developed Low
Volume Low Pressure spray guns by adopting new atomizing technology (patented).

5
Low pressure spray guns

Large type
Small type low pressure
low pressure spray gun Ultra small type
spray gun low pressure
LPH-200-122P spray gun
LPH-101-144LVG Pressure
Gravity feed type LPH-50-102G
feed type
with PC-4S cup Gravity feed type
Small type low with PC-51 cup
（option） pressure （option）
spray gun
LPH-101-164LVS
Suction feed type
with PCL-7B-2
● Pressure feed type LPH-101-122P
（option） …for industrial painting of metal, woodwork and resin
①You can reduce paint consumption by 20～30%（compared
New fluid nozzle mechanism
　
（Patent No.3359771 / LPH-101LVG-S）
with our previous models）due to high transfer efficiency aud
little overspray.
②They can contribute to health protection of painters due to
● Gravity feed type LPH - 50 - 042G / - 062G / -102G little overspray and bounceback.
…for automobile refinishing applications ③Maintenance cycle of spray booth is lengthened since booth
①Most suitable for touch-ups or shading with small fluid output,
becomes less dirty.
low pressure, and low air volume. Little overspray improves ● Pressure feed type LPH-200-122P
painting efficiency.
…for large workpieces such as large parts or vehicles
②Little overspray and bounceback contribute to health
①You can reduce paint consumption by 20～30% (compared
protection of painters.
with our previous models) due to high transfer efficiency.
● Lowair volume type LPH-101-124LVG / -144LVG・S/ ②They can contribute to health protection of painters.
　-164LVG・S
…for automobile refinishing applications ★ Spray guns for pressure feed type and corrosive
①Equipped with low pressure and low air volume, you can adjust in paints（option of LPH-200）
the same way as conventional spray guns. They enable you to … for line painting in automobile or consumer electronics plants
improve painting operation efficiency with less overspray mists, When you spray corrosive paints with large fluid output at high
especially when you do touch-ups and shading. frequency, we prepare an optional fluid nozzle and fluid needle
②Little overspray and bounceback contribute to protection of set ※ made of anti-wear material.
health of painters. ※ The parts consist of a fluid nozzle and fluid needle set.

Fluid Atomizing Required

nozzle air Pressure Air Fluid Pattern Applied
Previous High air Mass
Model Type of orifice pressure in air cap consumption output width air cap
compressor Application
model feed MPa MPa 　/ min
atomization model
φmm
（psi） （psi） 　
（cfm） m /min. mm（inch） kW g（lbs）

LPH-50-042G － 0.4 8※ 40（1.6）

※ ●
0.6 0.09 0.05 50 25 60（2.4）
※
● 220 Automotive refinish
LPH-50-062G － Gravity （12.8）
※
E2 0.2～0.75
（7.1） （1.8） （0.48）（touch-ups, shading）
LPH-50-102G － 1.0 55※ 100（3.9）
※
●

LPH-101-081P － 0.8 0.26 100 170（2.4）

430
（36.9） （15.5） E1 1.5～2.2
LPH-101-101P － 1.0 150 200（7.9）
※

LPH-100-122P 1.2 0.07 ● G2 2.2～3.7 Automotive refinish

LPH-101-122P 0.34（49.8） 530（18.7） 350 270（10.6）
（10.0） （touch-ups, block painting）
LPH-101-131P － Pressure 1.3
0.26 430 200 E1
（36.9） （15.5） 280（10.9）
LPH-101-151P － 1.5
LPH-101-082LVP － 0.8 100 230（9.0）
0.18 280 Metal, woodwork,
（25.6） （5.6） LV6
LPH-101-102LVP － 1.0 150 250（9.8） ● resin painting
0.05 295
LPH-101-124LVG LPH-101-124LVG 1.2 （7.1） 80※ 200（7.9）
※
（0.64）
0.1 200
1.4 （14.2） （7.1） 220（8.6） ● 1.5～2.2
LPH-101-144LVG LPH-101-144LVG 130※ ※

Gravity
LPH-101-164LVG LPH-101-164LVG 1.6 0.07 100 220（8.6） ●
0.13 240
LPH-101-184LVG － 1.8 （18.5） （10.0） （8.5） 120 210（8.2） ● LV4 Automotive refinish

LPH-101-124LVS － 1.2 60 170（2.4） ●

Suction 0.1 0.05 200 ●
LPH-101-144LVS LPH-101-144LVS 1.4 （7.1） （7.1） 80 180（7.0）
（14.2）
LPH-101-164LVS LPH-101-164LVS 1.6 95 190（7.4） ●
LPH-90-121 0.20 0.07 500 380 Large workpieces such
Large type LPH-200-122P Pressure 1.2 （28.4） （10.0） （17.7） 500 300（11.7） ● G2 2.2～3.7 （0.84） as large parts, vehicles
LPH-90-122

● Spray distance : 100mm for LPH-50-042G, 150mm for -062G and –102G, and 200mm for LPH-100 and – 200. ● Paint viscosity : 22 sec.（20 sec. / NK-2）
.
※ marked case : 16 sec（12 sec./ NK-2）. ● Fluid nipple : G1/4 for LPH-50 and LPH-100 ; and G3/8 for LPH-200. ● Air nipple : G1/4 for all models.

6
 Compact spray gun

W-101-151S
Suction feed type
PCL-7B-2
container (option)

① Lower atomizing air pressure

coupled with high atomization
We have reduced both overspray and triggering
load by reducing atomizing air pressure（at gun
handle）by 0.05 MPa. Atomization effect is
better than previous model.

② Wide lineup range

We have added 1.3 and 1.5Φmm to pressure
feed type. For automotive refinish, the popular
13H21 type has been expanded to 134G /134S.

W-101-132G
Gravity feed type
PC-4S
cup (option)

W-101-082P
Pressure feed type

Fluid Atomizing Required

Previous Type of nozzle air Air Fluid Pattern High General Applied air Mass
Model atomization atomization air cap Application
model feed orifice pressure consumption output width
compressor
MPa
model
　/ min
φmm （psi） 　
（cfm） m /min. mm（inch） kW g（lbs）

W-101-082P W-100-082P Pressure 0.8

0.29
150 190（7.5） ● Automobile, woodwork,
270
（42） （9.5） furniture, metal, plastic
W-101-102P W-100-102P Pressure 1.0 220（8.7） ●
200 E2P 1.5
W-101-132P W-100-132P Pressure 1.3
220
210（8.3） ● Woodwork, furniture, metal,
（7.8） medium viscosity
W-101-152P W-100-152P Pressure 1.5 250 240（9.4） ●
W-101-101S W-100-101S Suction 1.0 75 85 120（4.7）
● E1 Light industry, hobby
（2.6）
W-101-101G W-100-101G Gravity 1.0 95 130（5.1）
0.24 0.4～0.75
W-101-131S W-100-131S Suction 1.3 （34.8） 150 155（6.1）
145
（5.1） ● K1
W-101-131G W-100-131G Gravity 1.3 160 170（6.7）

W-101-132S W-100-132S Suction 1.3 150 160（6.3） Automotive refinish,※

225 295 woodwork, furniture,
（7.9） ● H2
W-101-132G W-100-132G Gravity 1.3 160 175（6.9） metal, plastic
0.20（29） 210（7.4） 140※ 180※（7.1）
W-101-134S W-100-134S Suction 1.3
0.24（34.8） 250（8.8） 145 200（7.9）
● H4 0.75～1.5
W-101-134G 0.20（29） 210（7.4） 155※ 205※（8.1）
W-100-134G Gravity 1.3
0.24（34.8） 250（8.8） 170 220（8.7）
W-101-151S W-100-151S Suction 1.5 175 170（6.7）
145 Woodwork, furniture, metal
（5.1） ● K1
W-101-151G W-100-151G Gravity 1.5 200 180（7.1）

W-101-152S W-100-152S Suction 1.5 0.24 170 175（6.9） Automotive refinish,

225
（34.8） （7.9） ● H2 woodwork,furniture, metal
W-101-152G W-100-152G Gravity 1.5 190 190（7.5）
1.5
W-101-181S W-100-181S Suction 1.8 210 170（6.7）
170 N1 Woodwork, furniture, metal
（6.0） ●
W-101-181G W-100-181G Gravity 1.8 240 190（7.5）

● All models, spray distance: 200mm ● Paint viscosity: 22 sec. (20 sec/NK-2).※ marked case: 16 sec.(12sec./NK-2) ● All models, fluid nipple: G1/4, air nipple: G1/4

W-101-131S/G W-101-132S/G W-101-134S/G

※ Three kinds of air cap sets are
　prepared for W-101 type
　1.3mm spray guns. Thicker film in the center of Film is more uniform and Suitable for overlapping spray several
pattern and thinner on both ends. thinner on the whole. times. A wide pattern of high atomization,
uniform mist dispersion and film thickness
even at a short spray distance.

7
Large type spray gun
①Lower atomizing air pressure
and noise level
We have reduced air noise level during W-200-152G
operation by about 5dB（A）by reducing Gravity feed
atomizing air pressure (at gun handle) PC-4
by 0.05 MPa, in addition to reduction of cup (option)
overspray.

②Improved atomization
W-200-122P is easy to spray at line
painting for high atomization. New W-200-
182S can be used in a wide field such as
automotive refinish and woodwork.

W-200-202S
Suction feed
W-200-122P PCL-10B-3
Pressure feed container (option)

Fluid Atomizing Required

Air Fluid Pattern
Previous
nozzle air High General Applied air
Model Type of orifice pressure consumption output width atomization atomization air cap compressor Mass Application
model feed model
φmm MPa 　/ min
（psi） 　
（cfm） m /min. mm（inch） kW g（lbs）

W-87-12G2P 400 Large workpieces and line painting

W-200-122P Pressure 1.2 560（19.8） 500 （15.7） ● G2P 2.2～3.7
W-90-12G2P such as large parts and vehicles
W-87-15K5S 210
W-200-151S Suction 240 （10.3）
W-90-14J5S
200（7.1） ● K1 0.75～1.5 Woodwork, furniture, metal
220
W-200-151G W-87-15K5G Gravity 270 （8.7）
1.5
W-87-15K2S 290
W-200-152S Suction 240 （11.4）
W-90-14J2S
320 Automotive refinish, woodwork,
W-200-152G W-87-15K2G Gravity 330（11.7） 270 （12.6） ● K2
furniture (finish), plastic (top coat)
340
W-200-182S W-90-18N2S Suction 1.8 290 （13.4）
0.29 380
W-87-20R5S （42.7） 260 （0.84）
W-200-201S Suction 350 （10.2）
W-90-18N5S Metal, woodwork, furniture,
260（9.2） ● R1 medium viscosity
280
W-200-201G W-87-20R5G Gravity 410 （11.0） 1.5～2.2
2.0
290
W-200-202S W-87-20R2S Suction 350 （11.4）
● Metal, woodwork, furniture,
R2 medium viscosity
320
W-200-202G W-87-20R2G Gravity 410 （12.6）
360（12.7）
W-87-25W5S 280
W-200-251S Suction 440 （11.0）
W-90-25W2S Metal, woodwork, furniture,
2.5 ● W1 anti-corrosion on steel frame,
310 adhesives, high viscosity
W-200-251G W-87-25W5G Gravity 510 （12.2）

● All models, spray distance: 250mm ● Paint viscosity: 22 sec. (20 sec/NK-2). ●All models, fluid nipple: G3/8, air nipple: G1/4
Note) When you spray corrosive paints in a car maker or consumer electronics line (pressure feed) with a spray gun with large fluid output at high frequency,
we prepare a fluid nozzle and fluid needle set made of anti-corrosive material.

8
 Center cup gravity feed spray gun

LPH-80/LPH-300/W-300/LPH-400/W-400

Low pressure General purpose Low pressure General purpose Low pressure
Ultra small type small type center small type center large type center large type center
center cup gravity cup gravity cup gravity cup gravity cup gravity
feed spray gun feed spray gun feed spray gun feed spray gun feed spray gun
LPH-80 W-300-132G LPH-300-144LV W-400-142G LPH-400-144LV
gravity feed gravity feed gravity feed gravity feed gravity feed
PCG-2D-1 PCG-2P-2 PCG-2P-2 PCG-6P-M PCG-6P-M 　New fluid nozzle mechanism
cup (option) cup (option) cup (option) cup (option) cup (option) （No.3359771 LPH-300/400LV）

①Well-balanced center of gravity ③Environment-friendly spray gun

●As cup is situated at the top of spray gun,well-balanced ● LPH-300/400 are environment-friendly low air volume low
center of gravity assures good fit to human hand. pressure spray guns with high transfer efficiency and
●Total weight is 15% lighter than previous models. little overspray.
（LPH/W-400） ● W-400 has achieved high transfer efficiency despite being
general purpose guns
②With well-dispersed mist, spray since atomizing air pressure (at gun handle) has been reduced
pattern is flat and thin. by 0.05 MPa～0.15MPa compared to previous models.
●You can get uniform film of water borne or high-solid paints ④Fluid filter is fitted as standard accessory.
which have been considered difficult to paint up to now.
● 60 mesh filter prevents dust.（PCG-6P-M/PCG-2P-2）

Fluid Atomizing Pressure Fluid Pattern Applied Required

nozzle air Air High General air cap Mass
Name Model Previous Type of in air cap consumption output width air Application
orifice pressure atomization atomization model
model feed MPa 　/min compressor
φmm MPa g（lbs）
（psi） 　（cfm） m /min. mm（inch）
（psi） kW

W-300-081G 0.8 － 80
（2.8） 60 100（3.9） ● E1 0.4～0.75
Light industry hobby
0.24 K1 0.4～0.75 320
W-300-101G 1.0 （35.6） － 145
（5.1） 100 130（5.1） ●
（0.71）
H2 Automotive refinish,woodwork
W-300-132G 1.3 － 225
（7.9） 160 175（6.9） ● 0.75～1.5 furniture,metal plastic
W-89-12K2G 0.20
（28.5） （9.9） 140
280 230（9.1）
W-400-122G W-89-12K5G 1.2 － ●
Center cup gravity feed spray gun

0.29
W-89-12R5G （42.7） （13.1） 160
370 250（9.8）
0.20
（28.5） 280
（9.9） 160 260（10.1）
W-400-132G 1.3 － ●
0.29 370
（13.1） 200 300（11.8）
（42.7） Automotive refinish
0.20 LV2
（9.9） 210
280 280（11.0） （touch-ups～top coat）
Gravity （28.5） ●
W-400-142G 1.4 0.29
－
（42.7） （13.1） 265
370 320（12.6）
1.5～2.2 380
W-89-15K2G 0.20 （0.84）
（28.5） （9.9） 240
280 300（11.8）
W-400-162G W-89-15K5G 1.6 － ●
0.29
W-89-15R5G （42.7） （13.1） 310
370 340（13.4）
0.20
（28.5） （10.2） 320
290 280（11.0） Clear medium/
W-400-182G W-89-20R5G 1.8 0.29
－ ● LV1
（13.4） 400
380 320（12.6） high viscosity
（42.7）

0.29
W-400-251G W-89-25W5G 2.5 （42.7） － 360
（12.7） 580 340（13.4） ● W1 Primer high viscosity

LPH-300-124LV 1.2 90
※
210（8.3） ●
0.1 0.05 Automotive refinish
200（7.1）
（14.2） （7.1） ● 320
LPH-300-144LV 1.4 130
※
230（9.1） LV4 1.5～2.2
（0.71）
（touch-ups～block
Low pressure center

0.13 0.07 painting）

cup gravity feed

LPH-300-164LV 1.6 （18.5） （10.0）

240（8.5） 110 230（9.1） ●
spray gun

Gravity
1.4 130 290（11.4） ● Automotive refinish
LPH-400-144LV
（touch-ups～block
0.11 0.07 LV4 1.5～2.2 380 painting）
（15.7） 270（9.5）
（10.0） （0.84） base coat, top coat,
LPH-400-164LV 1.6 150 300（11.8） ● clear

LPH-80-042G 0.4 8 40
（1.5） ●

LPH-80-062G 0.6 25 60
（2.3） ●

LPH-80-082G 0.8 0.09 0.07 50 40 80

（3.1） ● E2 0.2～0.75
（13.1） （10.0） （1.7）
cup gravity feed spray gun
Ultra small type center

LPH-80-102G 1.0 55 100

（3.9） ●
Low pressure

LPH-80-122G 1.2 80 120

（4.7） ●
Gravity Automotive refinish
205
spot repair
LPH-80-044G 0.4 10 55 ●

LPH-80-064G 0.6 30 80 ●
0.1 0.07 60
LPH-80-084G 0.8 45 100 ● E4 0.2～0.75
（14.2） （10.0） （2.1）
LPH-80-104G 1.0 60 130 ●

LPH-80-124G 1.2 75 140 ●

9
Waterborne paint spray gun

W-300WB/W-400WB
We are facing an environmental issue on a global basis today,
especially in the automotive refinishing market, whose paint
trend is changing from solvent borne paints to waterborne
paints in order to address such an issue.

To meet the need for change in today’s automotive refinishing

market, these spray guns have been developed to create
optimum atomization for waterborne paints with particular
features.

Features:
1. Fluid nozzle design
The patented concave and slit design fluid nozzle
can help to create a fine and even atomization with
lower air pressure and air consumption for water-
borne paints which have higher viscosity.

2. Special air cap

The specially designed air cap for specific water-
borne paints can create a thin and even pattern.

3. Global recommendation
These spray guns are recommended by leading
paint manufacturers throughout the world as the
designated spray gun for their waterborne paints.

Waterborne paint Waterborne paint

spray gun spray gun
W-300WB-141G W-400WB-142G
gravity feed gravity feed
PCG-2P-2 PCG-6P-M
cup (option) cup (option)
　New fluid nozzle mechanism
（No.3359771 W-300WB/400WB）

Fluid Atomizing High Applied

Air Fluid Pattern General Required
nozzle air atomization air cap Mass
Name Model Type of consumption output width atomization air
orifice pressure model Application
feed 　/min compressor
φmm MPa g（lbs）
（inch） 　（cfm） m /min. mm（inch）
（psi） kW

0.15 190 250 320

W-300WB-141G 1.4 125 ● WB1 0.75～1.5
（21.8） （6.7） （9.8） （0.71）

140 290
W-400WB-122G 1.2 ●
300 （11.4）
（10.6） WB2
300
W-400WB-132G 1.3
（11.8）
160
0.18 230 290 380
W-400WB-141G 1.4 ● WB1 1.5～2.2 （0.84）
（26.1） （8.1） （11.4）

310
W-400WB-142G 1.4 （12.2）
390 250 ● WB2
（13.8） 340
W-400WB-162G 1.6 （13.8）

●All models, spray distance : 200mm ●Paint viscosity : 22 sec.（20 sec/NK-2）

●As for W-400WB, fluid nipple M16×1.5（male）, air nipple G1/4. As for W-300WB fluid nipple G1/4 （female）, air nipple G1/4.

10
 For Automotive Refinishing
B-Sho Series
"B-Sho series", spray gun series for automotive refinishing, was developed from our
thorough research with the object of improving maneuverability and of forming a fine film.
Our field research in how our customers use spray guns, and in what kind of conditions led us to
realize, what types of spray gun were wanted in the automotive refinishing market.
If you seek "more" for automotive refinishing than our popular spray guns, such as the
W-101 Series（General spray guns）and the LPH-101 Series（Low pressure spray guns） ,
then the "B-Sho"series is for you.

Lineup of Spray Guns for Automotive Refinishing

Touch-up paint Block paint Whole body paint

W-50-124BPG W-101-134BPG
Metallic / W-101-101 W-101-134 or 132 W-101-152
Pearl paint
LPH-50 LPH-101-144BPG LPH-101-164LV

W-50-124BPG W-101-142BPG
Solid / W-101-101 W-101-131 or 132 W-101-152
Clear paint
LPH-50 LPH-101-124 or 144LV LPH-101-164LV

W-101-162BPG
Primer surfacer /
W-101-131 W-101-151 W-101-181
Anti-corrosion paint
LPH-101-124LV LPH-101-144LV LPH-101-164LV

Settings for the first time use The following chart contains standard settings for "B-Sho series".

Air pressure（gauge） Fluid adj.knob Pattern adj.knob Air adj.knob Distance to

type the work
MPa （From full close） （From full close） （From full close）
mm
W-101-134BPG 0.2 full open 2 turns 2 turns 150～200
W-101-142BPG 0.25 full open 2.5 turns 2.5 turns 150～200
0.15 full open 1.5 turns 1.5 turns 100～150
W-50-124BPG
0.20 full open 2 turns 2 turns 100～150

※1 The air pressure is the setting air pressure of Air transformer gauge when used with 10m air hose.
※2 All the number of turns of adj knobs are counted from zero,full close.
※3 W-50-124BPG Air pressure(gauge)
　 for metallic/pearl paint:0.15MPa　　　for solid/clear paint:0.20MPa

Types Fluid Atomizing Air Pressure Air Required

Model Previous
of nozzle air
Fluid Pattern High General Applied air Mass Applicationl
model in air cap consumption output width atomization atomization air cap compressor
feed orifice pressure model
※1 ※3
MPa MPa /min mm g
※3
Фmm （psi） （psi） （cfm） /min （inch） kW （lbs）

W-50-124BPG Gravity 0.15 70

- （2.5） 160
85 （6.3） 185
̶ 1.2 （22.8） ● 50 0.4 （9.4） Paint for Automotive refinishing
Gravity 1.3
※2 0.20 160 250
W-101-134BPG W-100-134BPG （29.0） - （5.7） 140 （9.8） ● BP4 1.5
0.1 0.05 200 LPH Metallic/pearl paint
LPH-101-144BPG ̶ Gravity 1.4 130 220 ● 1.5～2.2
（14.2） （7.2）（7.1） BP4
0.24 230 270 295
W-101-142BPG W-100-142BPG Gravity 1.4 - （8.1） 200 （10.6） ● BP2 1.5 （0.7） Solid/clear paint
（34.8）
0.20 ※3 - 210 120 170
（29.0） （7.4） （6.7） 162
W-101-162BPG ̶ Gravity 1.6 ● 1.5 Primer/surfacer paint
0.24 ※4
230
- （8.1） 195 200 BP2
（34.8） （7.9）
※1 Atomizing air pressure is pressure readings at hand.
※2 The fluid nozzle for W-101-134BPG is incompatible.
※3 Paint viscosity is 40 sec. (40sec./NK-2) for primer surfacer paints.
※4 Paint viscosity is 22 sec. (20sec./NK-2).
Note) Paint viscosity is 12 seconds that is measured by NK-2 viscosity meter using automotive refinishing paint.
11
B-Sho series GOLD
"GOLD for metallic/pearl paint"
● Less darkening of the coating by reducing
scatterings. W-101-134BPG
● Realizes high atomization with low pressure.
● Less paint adhesion to the air cap.

"LVLP GOLD"
● Optimal atomization in low volume , low
　New fluid nozzle mechanism
pressure per new fluid nozzle. （No.3359771）

● Improving working environment by less

over spray.
● Reducing working process for exanple
LPH-101-144BPG
minimal masking area.

B-Sho series SILVER

"SILVER for solid/clear paint"
● The film is thicker in the middle,
therefore you can make thick and shiny
coating easily.
● The film is thinner on both ends, W-101-142BPG
and that reduces uneven coating.

B-Sho series B.B.

"Exclusive spray guns

W-101-162BPG
for base coat process"
● Fluid needle is quenched to increase its strength
in the same as with pressure feed type.
● Fluid nozzle orifice suitable for base coat　paints,
stable paint particles and stable spray pattern
have reduced spitting and shortened polishing time.

"Exclusive spray guns

for small area and top coating"
● Less darkening of the coating by reducing scatters.
● Realizes high atomization with low pressure.
● Less paint adhesion to the air cap. W-50-124BPG

12
 Automotive Refinishing Spray Gun

SERIES
This series is specialized for today’s eco friendly paint such as 1K low solvent base coat
and high solid clear etc. Today’s eco friendly paint has higher coverage capability so that
coverage is completed with less passes by the painter, and contains lower VOC. To bring
out these paint features maximally, this series can offer exceptional wet coat coverage by
utilizes it’s flat ＆ wide pattern.

[base] [clear]

S ERIE S

W101-138BGC /
W101-148BGC
■　Item ■　Specifications
Application BASE COAT CLEAR COAT fluid nozzle Atomizing Air Pattern Pattern Applied air Required air
Fluid output Mass
Model orifice air pressure consumption adj.knob width cap model compressor
Model W101-138BGC W101-148BGC mm MPa ℓ/min From full close mℓ/min mm kw g

【BASE】 2.5 turns（usual） 150 220

Spray gun W-101-138BG W-101-148BG Φ1.3 0.20 230 B8 1.5～ 295
Set Includes

W-101-138BG 6 turns（full open） 185 260 2.2

Cap PC-400S-2LF PC-400S-2LF 2.5 turns（usual） 160 225
【CLEAR】 1.5～
Φ1.4 0.20 230 B8 295
Other W-101-148BG 6 turns（full open） 200 275 2.2
Spanner Spanner
accessories
●Spray distance is 200mm　●Paint viscosity is 12sec.（12sec/NK-2）　●As for W/LPH-101, fluid nipple G1/4（female）, air nipple G1/4.
※1The number of turns of fluid adj knob is counted from zero, full close.（Pattern and Air adj. Knobs are full open）
※2 Cup is PC-400S-2LF.（400ml, Stainless, Free-angle）

W101-136BGC / W-101-136BG
■　Item ■　Specifications
fluid nozzle fluid nozzle Atomizing Air Pattern Fluid Pattern Applied air Required air
φ1.3 Mass
orifice orifice air pressure consumption adj.knob output width cap model compressor
Model
Model W101-136BGC mm MPa ℓ/min From full close mℓ/min mm kw g
3 turns（usual） 170 245
Spray gun W-101-136BG φ1.3 0.20 230 B6 1.5～ 295
W-101-136BG
Set Includes

6 turns（full open） 190 260 2.2

Cap PC-400S-2LF
●Spray distance is 200mm　●Paint viscosity is 12sec.（12sec/NK-2）
Other ●As for W/LPH-101, fluid nipple G1/4（female）, air nipple G1/4.
S ERIE S Spanner
accessories ※1The number of turns of fluid adj knob is counted from zero, full close.（Pattern and Air adj. Knobs are full open）
※2 Cup is PC-400S-2LF.（400ml, Stainless, Free-angle）

13
Optimized SERIES model
by paint manufacture.
We created “A ultimate tool” by making improvement and refering to the advice of paint
manufactures’ field support members who are working on the flont line of refinish coating.

Nozzle chart of Kansai Paint

This gun is optimized for“Retain PG Hyblid Eco/HS system”
from standard series.
S ERIE S

■　Item
fluid nozzle
φ1.3 φ1.4
orifice

Model W101-136KPGC W101-146KPGC

Spray gun W-101-136KPG W-101-146KPG

Set Includes

Cap PC-400S-2LF PC-400S-2LF

Other
accessories
Spanner Spanner
W101-136KPGC /
W101-146KPGC
■　Specifications
fluid nozzle Atomizing Air Pattern Fluid Pattern Applied air Required air
Type of Mass
Model orifice air pressure consumption adj.knob output width cap model compressor
feed
mm MPa ℓ/min From full close mℓ/min mm kw g
3 turns（usual） 140 220
W-101-136KPG Gravity Φ1.3 0.20 200 KP5 1.5～ 295
6 turns（full open） 165 240 2.2

3 turns（usual） 150 225 1.5～

W-101-146KPG Gravity Φ1.4 0.20 200 KP5 295
6 turns（full open） 170 245 2.2

●Spray distance is 200mm　●Paint viscosity is 12sec.（12sec/NK-2）　●As for W/LPH-101, fluid nipple G1/4（female）, air nipple G1/4.
※1The number of turns of fluid adj knob is counted from zero, full close.（Pattern and Air adj. Knobs are full open）
※2 Cup is PC-400S-2LF.（400ml, Stainless, Free-angle）

Nozzle chart of Nippon Paint

This gun is optimized for“Nax Real e3 System”
from standard series.
S ERIE S

■　Item
fluid nozzle
φ1.3 φ1.4
orifice

Model W101-136NPGC W101-146NPGC

Spray gun W-101-136NPG W-101-146NPG

Set Includes

Cap PC-400S-2LF PC-400S-2LF

Other
accessories
Spanner Spanner
W101-136NPGC /
W101-146NPGC
■　Specifications
fluid nozzle Atomizing Air Pattern Fluid Pattern Applied air Required air
Type of Mass
Model orifice air pressure consumption adj.knob output width cap model compressor
feed
mm MPa ℓ/min From full close mℓ/min mm kw g

W-101-136NPG Gravity Φ1.3 0.15 160 3 turns

（usual） 115 155 NP5 1.5～ 295
2.2

Gravity Φ1.4 0.15 160 6 turns（full open） NP5 1.5～ 295

W-101-146NPG 120 165 2.2

●Spray distance is 150mm　●Paint viscosity is 11sec.（12sec/NK-2）　●As for W/LPH-101, fluid nipple G1/4（female）, air nipple G1/4.
※1The number of turns of fluid adj knob is counted from zero, full close.（Pattern and Air adj. Knobs are full open）
※2 Cup is PC-400S-2LF.（400ml, Stainless, Free-angle）

14
 SERIES

W-50-136BGC
Launch new small size of SERIES .
succeed to flat and wide pattern to make use of the
feature of environmentally considerate paint such as 1K base coat,
etc.
And we gather the best that advanced atomization technology has to
offer for this gun to reach the highest, in Japanese.

S ERIE S

Even if the gun body is small, the gun succeeds to flat and wide pattern.
We developed atomization quality so that coating result would be the same level of the other SERIES
as good leveled surface.
Gun body is plated twilight chrome plate to symbolize SERIES . And the profound gross plate arranges
to appearance of fine quality.

■　Range (image)
Lower air pressure
's pattern width keep larger
comparing with W-101's pattern width Standard air pressure
Pattern width

W-50-136BGC W-101-136BGC W-50-136BGC W-101-136BGC

W-101-136BGC Atomizing air pressure (Mpa/psi) 0.1(14.5) 0.1(14.5) Atomizing air pressure (Mpa/psi) 0.15(21.8) 0.2(29.0)
Fluid adj 2 rotation 2 rotation Fluid adj 2.5 rotation 2.5 rotation
Spray distance (mm) 100 100 Spray distance (mm) 150 200
W-50-136BGC Air consumption (l/min/cfm) 55(1.9) 150(5.3) Air consumption (l/min/cfm) 70(2.5) 230(8.1)
Fluid output (ml/min) 40 80 Fluid output (ml/min) 70 145
Pattern width (mm/inch) 129(5.1) 110(4.3) Pattern width (mm/inch) 190(7.5) 240(9.4)
W-101-138BGC
　　　 -148BGC

W-50-124BPG
Fluid out put

■　Range (image)

Type of feed Fluid nozzle Atomizing air Air Pattern Applied Required
Model orifice pressure consumption Fluid output wdth air cap compressor Mass
(mm) (Mpa/psi) (l/min/cfm) (ml/min) (mm/inch) (kw) (g)

W-50-136BGC Gravity 1.3 0.15(21.8) 190(7.5) 70 190(7.5) W-50-B6 0.4 195

※Cup is PC-150SB-2LF (130ml,SUS, Free-angle)

15
16
 Countries where 0,7 bar (10 psi) inside air cap is mandatory, users with environment and green economy in
mind will appreciate new Supernova Entech spray gun: new unique design, Anest Iwata pre-atomization nozzle
technology which we call SPLIT NOZZLE™, is able to deliver flat and thin large and optimized wet controlled
spray pattern. The air cap/nozzle sets for Dry and Wet weather conditions allow the use in each environmental and
temperature conditions.

NOT Plated or Anodized Alluminium or Brass!

For the first time, the angle of the cup has been
designed with both disposable and standard
SPLIT NOZZLE, This innovative technology cups in mind.
has continued to evolve and in doing so The SUPERNOVA design guarantees perfect
increases your spraying experience……. balance, even when using disposable cups
Plus this technology promises an easy and which, being wider and sometimes longer,
premium painting job with its WET CON- could affect balance.
TROL nozzle system.

Lower pressure and lower air consumption.

A Long flat uniformed spray pattern with a
fine and consistent droplet enables an easy-to-control
painting overlap which achieves a premium quality paint
job every time. No need for a removable baffle on the front of the gun,
which means fewer spare parts!
SPLIT NOZZLE The atomizing air flow cuts the paint The air cap has a larger thread, making it both robust and
stream like a knife and controls the droplets efficiently… easy to remove and it has been designed with low mainte-
Working at a lower pressure enables lower air con- nance in mind.
sumption through the flat tip nozzle system. The new, larger slots in the air cap ring facilitate quick
removal and refitting after cleaning.
Standard
A long flat uniform spray pattern with a fine and
consistent droplet size achieves an easily controlled
paint overlap, this also gives you a premium quality
application of all paints with its superior wet control.

0,05 bar 0.1 bar 0.2 bar 0.3 bar

S p l i t n oz z l e
17
The astonishing range of set ups, both for base coat (WB or HS) and clear coat, make the SUPERNOVA EVOTECH
suitable to spray in every climatic condition with optimized atomization.
ANEST IWATA exclusive pre-atomization split nozzle technology allows large spray pattern, with same particles
size both ends of the spray pattern, and makes it easy to adjust the speed and distance according to the needs.

The new locking thread system enables you to experience a

secure and precise screwing and unscrewing of the paint cup.

SUPERNOVA has new sturdy

constructed high precision adjusters.
The carefully designed grip delivers the
professional painter a reliable and more
importantly comfortable feeling even
when wearing latex gloves.

The responsive trigger action gives the painter

complete control when applying tricky basecoats
and final coats.

The slim ergonomic grip of the SUPERNOVA spray gun helps

distribute weight and balance through the wrist, reducing the
risk of repetitive strains.

Atomization
Technology Product Feature Nozzle Variation
Standard delivery series.
Evotech atomizer (WS-400 evo) creates
For standard spray
consistent amounts of extreme fine paint
application
droplets, and lays them down consistently
onto the substrate painting surface. 1.3~1.4B/C, 1.3 OBS
It gives you a controlled application speed
Compliant while achieving a great premium quality HD series
(EPA approved) WS-400 EVO For wetter spray
finish.
application
This atomizer is EPA approved (compliant) 1.3~1.5HD
Entech atomizer (LS-400 entech) is a new ET series
generation of HVLP atomizer’s and is For standard spray
designed to have the maximum potential for application.
a HVLP system with the new ANEST IWATA ET 1.2~1.5
concept (Wet control).
• Low paint consumption
• Extremely low spray noise ETS series (form 1.2~1.5)
• Optimized nozzle with Spray distance & wetness For wetter & long spray
HVLP LS-400 ENTECH Two series of nozzle (ET & ETS) distance application
• Wider working climate range ETS 1.2~1.5
( Hot & Dry climate compatible) 18
 SUPERNOVA offer to sprayers the most evolved and sophisticated range of atomizations,
thanks to its unique SPLIT NOZZLE principles.
If you are spraying diffi cult water borne metallic base coats in extreme humidity conditions
or extreme temperature conditions, you can choose the most suitable atomizer.

Supernova series application and climate

STANDARD series
1.3 - 1.4B
HD series
EVOTECH
1.3 - 1.5 HD COMPLIANT

ET series
1.3 - 1.4 ET
ETS series ENTECH
1.3 - 1.4 ETS HVLP

DRY application WET application

STANDARD climate HOT & DRY climate

High humidity Low humidity
Low temperature High temperature

Type of
Model
ø mm MPa ℓ/min mℓ/min MIN MAX MAX No. g
application
WS-400 EVO
WS-400-1301B-S1 BASE 1.3 140 -
WS-400-1301C-S1 CLEAR 1.3 365 - Standard
170 260
WS-400-1401B-S1 BASE 1.4 - application
spray distance 130 mm

spray distance 200 mm

spray distance 300 mm

WS-400-1401C-S1 CLEAR 1.4 190 370 - 695

with cup
WS-400-1301BHS1 -
1.3 HD 0.2 370 220 265 365 WS-400-01
WS-400-1301CHS1 - 475
without
WS-400-1401BHS1 - cup Wetter
1.4 HD 240 270
WS-400-1401CHS1 - application
370
WS-400-1501BHS1 -
1.5 HD 260 275
WS-400-1501CHS1 -
LS-400 ENTECH
LS-400-1305-S1 ET 1.3 160 250 350 - 695 Standard
400
spray distance

spray distance

spray distance

LS-400-1405-S1 ET 1.4 170 260 360 -

with cup application
130 mm

200 mm

300 mm

0.18 LS-400-05
LS-400-ETS13-S1 ETS 1.3 160 400 475 Wetter & Longer
420 235 310 without spray distance
LS-400-ETS14-S1 ETS 1.4 180 410 cup

Max. working pressure: 7.0 bar Temperature range: 5~40° C Air nipple: G 1/4” M Fluid nipple: G 1/4” F

19
Small and medium spray guns
W-71/W-61/W-77
● Delivery conditions of these models will be longer in some cases.

W-77-02
pressure
feed

How to read model names

Ex. W-77- 21G

W-71-1S Type of feed
G : Gravity type
W-61-3G S : Suction type
suction feed
gravity feed 1. 2. 3. general purpose
PCL-10B-2
PC-4S 11. 12. 31. high quality painting
container 0（zero）mass production painting
cup (option)
(option)
gun body W71,W61 : small
W77 : medium

Fluid nozzle Spray Atomizing Air Fluid Required

orifice distance air pressure consumption output Pattern width Mass Standard container or cup
Model Type of feed air compressor
φmm mm（inch） MPa（psi） 　/ min（cfm） m /min. mm（inch） kW g（lbs）

W-71-0 0.8 0.34 240（8.5） 200 190（7.5）

Pressure 1.5 Paint tank, diaphragm paint pump
W-71-02 1.0 （49.8） 230（8.1） 300 265（10.4）
W-71-1S 1.0 75（2.6） 95 100（3.9）
0.4 Container
W-71-2S 1.3 85（3.0） 135 135（5.3）
PC-1S（1000 　）
W-71-3S 1.5 165（5.8） 180 170（6.7） 0.75 PC-2（600 　）
Suction
W-71-21S 1.3 195（6.9） 140 155（6.1） PC-3（400　 ）
PCL-10B-2（1000　 ）
W-71-31S 1.5 200 0.29 230（8.1） 170 170（6.7） 1.5 450 PCL-7B-2（700　 ）
（7.9） （42.7） （0.99）
W-71-4S 1.8 230（8.1） 195 195（7.7）
W-71-1G 1.0 75（2.6） 110 120（4.7） Side mount cup
Medium spray guns　　　　　　　　　　　　　　　　　　Small spray guns

0.4 PC-4S（400 ）
W-71-2G 1.3 85（3.0） 155 155（6.1） PC-5（250 ）
W-71-3G 1.5 165（5.8） 210 185（7.3） 0.75 PCG-6P-2（600 ）
Gravity PC-51（220 ） （stainless steel）
W-71-21G 1.3 195（6.9） 160 165（6.5） PC-61（130 ） （stainless steel）
PC-150S-2LF
W-71-31G 1.5 190 185（7.3） 1.5
230（8.1） PC-400S-2LF
W-71-4G 1.8 220 220（8.7） PC-250S-2LF
W-61-0 Pressure 0.8 0.34（49.8） 200（7.1） 200 190（7.5） 1.5 Paint tank, diaphragm paint pump
W-61-1S 1.0 75（2.6） 95 100（3.9）
Container　　　PC-3（400 ）
0.4
W-61-2S Suction 1.3 85（3.0） 135 135（5.3） PC-1S（1000 ）PCL-10B-2（1000 ）
200 0.29 420 PC-2（600 ） PCL-7B-2（700 ）
W-61-3S 1.5 150（5.3） 160 185（7.3） 0.75 （0.92）
（7.9） （42.7）
Side mount cup　PC-4S （400 ）
W-61-1G 1.0 75（2.6） 110 120（4.7） PC-5（250 ）
0.4 PC-51（220 ） （stainless steel）
W-61-2G Gravity 1.3 85（3.0） 155 155（6.1） PC-61（130 ） （stainless steel）
PC-150S-2LF
PC-400S-2LF
W-61-3G 1.5 150（5.3） 190 220（8.7） 0.75 PC-250S-2LF

W-77-0 430（15.2） 445（17.5）

Pressure 1.2 480 2.2～3.7 Paint tank, diaphragm paint pump
W-77-02 420（14.8） 400（15.7）
W-77-1S 180（6.4） 210（8.2） 0.75～1.5
W-77-11S 1.5 290（10.2） 255 260（10.2） 1.5～2.2 Container
PC-1（1000 ）
W-77-12S 370（13.1） 230（9.1） 2.2～3.7
Suction PCL-10B-3（1000 ）
W-77-2S 250（8.8） 345 255（10.0） 1.5 PCL-7B-3（700 ）
2.0
W-77-21S 340（12.0） 350 PC-19R（1000 ）
250 0.34 270（10.6） 550
（9.8） （49.8） 1.5～2.2 （1.21）
W-77-3S 2.5 325（11.5） 435 280（11.0）
W-77-1G 180（6.4） 230（9.1） 0.75～1.5
W-77-11G 1.5 290（10.2） 285 290（11.4） 1.5～2.2
Side mount cup
W-77-12G 370（13.1） 255（10.0） 2.2～3.7 PCG-6P-3（600 ）
Gravity
W-77-2G 250（8.8） 290（11.4） 1.5 PC-4（400 ）
2.0 390
W-77-21G 340（12.0） 335（13.2）
1.5～2.2
W-77-3G 2.5 325（11.5） 485 330（13.0）

● W-71, W-61, fluid nipple: G1/4 (PF1/4), air nipple: G1/4 (PF1/4); W-77, fluid nipple: G3/8 (PF3/8), air nipple: G1/4 (PF1/4)

20
 Automatic spray guns Spray guns for mass production which are
used with automatic painting equipment,
reciprocators or painting robots

LPA-101 LPA-200
WA-200
Compact type Large type
Large type
low pressure low pressure
automatic gun
automatic gun automatic gun

WA-101R
Round pattern
automatic gun

SGA-101
Mini type WA-101
automatic gun
Compact type
(air piston type) 200 Length of extension nozzle（A）
for intermittent automatic gun
painting
θ

System diagram Atomizing air

Air transformer
WA-0609
internal coating
Operating control air automatic gun
CAP marked
Three way
solenoid valve Compressor
CYL marked
Air transformer

Paint tank Model Length of extension nozzle（A） Pipe dia Pattern curve degree（θ）
Fluid nipple
Air flow WA-1218 180mm 12mm about 19°
Diaphragm paint pump Paint flow WA-0915 150mm 9mm about 14°
WA-0609 90mm 6mm about 4°

Compact type high performance

automatic guns
①You can change and remote WRA-200
control pattern width during Large type
painting by controlling center WRA-101
air and horn air independently, Compact type
resulting in reduced overspray.
②You can circulate paints
such as metallic paints which System diagram Two way
solenoid Air
deposit in a short time. Atomizing air（center）
valve transformer

③Compact gun body needs

Pattern air Two way solenoid valve
small installation space and （horn）

can be used with automatic CAP

marked
FAN marked
Air
Operating control air transformer
painting equipment including Three way
solenoid valve Compressor
painting robot. CYL marked
Air
transformer
[Caution] FLU
marked
LRA-200 Paint tank
①As this automatic gun has no built-in
air valve, refer to system diagram on
low pressure Air flow
Diaphragm paint pump
Paint flow
the right.
②Joints are available on the market.

21
 Fluid Air Air
Spray pressure pressure Air
nozzle in air consumption Fluid Pattern Applied Required
Model Name Type of orifice distance at gun cap output width air cap air Mass Application
inlet
feed
Φmm mm MPa MPa 　/min model compressor
（inch） （psi） （psi） 　（cfm） m /min. mm（inch） kW g（lbs）

SGA-101 Compact 1.0 ー 0.24（35.6） ー 80（2.8） ー ー E1 0.4～ 270（0.59） Mold release agents, water borne solvent
WA-101-082P
（V） 0.8 270（9.5） 150 190（7.5） E2P 1.5～ Small workpieces

WA-101-101P
（V） Pressure 200 ー 90（3.2） 100 140（5.5） E1 0.75～ 460 Small fluid output
Small 1.0 （7.9） （1.01）
WA-101-102P
（V） 270（9.5） 200 220（8.7） E2P
1.5～ Small workpieces
WA-101-132P
（V）
※ 1.3 ー 260（9.2） 250 230（9.1） H2
0.29
WA-200-122P
（V） 1.2
（42.7） 530（18.7） 500 400（15.7） G2P
WA-200-152P ※ 1.5 250 330（11.7） 270 340（13.4） K2 500
General Large Pressure ー 2.2～ Large workpieces
（9.8） （1.1）
purpose WA-200-202P ※ 2.0 400 320（12.6） R2
automatic 360（12.7）
WA-200-251P ※ 2.5 500 330（13.0） W1
gun
Round
WA-101R-05P
（V） pattern Pressure 0.5 200（7.9） ー 40（1.4） 20 35（1.4） － 0.2～0.4 440（0.97） Small workpieces, touch-ups
WA-1218 0.6 73（2.6） 17 48（1.9） － 555（1.22）
Internal Pressure 200 0.29
WA-0915 coating （Gravity） （7.9） （42.7） ー 55（1.9） 9 36（1.4） － 0.4 510（1.12） Internal coating of small tube
0.5
WA-0609 48（1.7） 6 32（1.3） － 475（1.05）
WA-200-201ZP 2.0 250 0.34 R1Z 500 Ceramic enamels, abrasives
Ceramic Pressure （49.8） ー 500（17.7） 760 370（14.6） 2.2～3.7
（9.8） （1.1） similarly abrasive fluids
WA-200-251ZP 2.5 R1Z
Low LPA-101-101P
（V）
pressure Small 1.0 200 0.26（38.4） 0.07 430（15.2） 150 200（7.9） E1 460（1.01） Small workpieces
automatic Pressure 2.2～3.7
LPA-200-122P
（V） （7.9） 0.20（28.4）（10.0）
gun Large 1.2 500（17.7） 500 300（11.8） G2 500（1.1） Large workpieces
Atomizing air
200
WRA-101-082P
（V） Small 0.8 （7.9）
0.26
（38.4）
Pattern air 270（9.5） 150 190（7.5） E2P 1.5 300（0.66） Small workpieces
0.22
（31.3）
Mounted ー
250 0.24（34.1）
on WRA-200-122P
（V） Large Pressure （9.8） 0.26（38.4） 530（18.7） 400（15.7） G2P
robot 1.2 500 2.2～3.7 325（0.72） Large workpieces
Low 200 0.14（19.9） 0.07
LRA-200-122P
（V） pressure （7.9） 0.16（22.8） （10.0） 500（17.7） 300（11.8） G2

Note）※marked WA-101 and 200 models are used as either gravity feed or suction feed. （Fluid output shows gravity feed type）
Regarding（V）marked models, you can select them equipped with locknut type fluid adj. set（stepless adj. system）.
Fluid nipple: G1/4 for WA-101/LPA-101 and G3/8 for WA-200/LPA-200.
Air nipple: G1/4 for all models but WRA and LRA are without both fluid and air nipples.

Automatic spray guns

Fitting dimensions（mm）
G
A

K
L

Diaphragm paint pump

J
F
H

3–M8 ×1.25
M with elevated stand
P

D
B φ
・Stand type which can move pump itself
C upwards or downwards.
It is easy to replenish paint.
E
・Most suitable when you supply paints to
Dimensional drawing for WRA and LRA multiple color painting line by placing
several sets in a row.
CYL
CAP FAN
12.5 12.5

12.5
A

J
F

C ×
（hole for gun fixing bolt）
E
FLU

WRA-100

B 5-Rc1/8

Model A B C 　D（Ф） E F G H J K L M P
WA-101 27 44.5 85.5 16 147 23.5 36 40.5 86 38 18 14.5 20
WA-101R 27 37.5 79 16 140.5 23.5 35 40.5 85 38 18 14.5 20
WA-200 30.5 47.5 89 16 148.5 23.5 36 40.5 86 38 18 14.5 20
LPA-101 27 47 88.5 16 150 23.5 36 40.5 86 38 18 14.5 20
LPA-200 30.5 47.5 89 16 148.5 23.5 36 40.5 86 38 18 14.5 20
WRA-101 27 40 51 － 109 14.5 － － 40 40
WRA-200 30.5 48 56 － 111 14.5 － － 40 40
LRA-200 30.5 48 56 － 111 14.5 － － 40 40
Paint tank would not be
SGA-101 27 － 34 10 － 34 DPS-90LE attached in product.
WA-1218 12 － 266 16 － 23.5 Position to attach gun stay differs Agitator would be provided
WA-0915 9 － 235 16 － 23.5 from the above drawing. as option item.
WA-0609 6 － 175 16 － 23.5

22
 Extension nozzle gun
For painting internal surfaces of pipes and
other hard-to-reach places.

How to read
model names

Ex. LW-10B-4530
LW-18B-9015
PC-17R
Pipe length：300mm Pressure feed
Head angle：45°
LW-10B-0030 container
Nozzle orifice（Ex.）10＝φ1.0/18＝φ1.8 （option）
Gun body model

Fluid Atomizing Fluid Spray Head Pipe Air Pattern

Model Previous nozzle Applied Type of air width Mass
atomization pressure output distance angle length consumption
model orifice air cap
Φmm MPa（psi） m /min. mm（inch） mm（inch） 　/ min（cfm） mm（inch） g（lbs）
°
LW-10B-0015 L88-0015 150（5.9）
LW-10B-0030 L88-0030 300（11.8） 520（1.14）
0
LW-10B-0050 L88-0050 500（19.7）
LW-10B-4515 L88-4515 150（5.9）
0.29 200
LW-10B-4530 L88-4530 1.0 E1 150 300（11.8） 90 175（6.9） 570（1.25）
（42.7） （7.9） 45
LW-10B-4550 L88-4550 500（19.7）
LW-10B-9015 L88-9015 150（5.9）
LW-10B-9030 L88-9030 300（11.8） 640（1.41）
90
LW-10B-9050 L88-9050 Fan pattern 500（19.7）
LW-18B-0015 （L87-0015） only 150（5.9）
LW-18B-0030 （L87-0030） 300（11.8） 520（1.14）
0
LW-18B-0050 （L87-0050） 500（19.7）
LW-18B-4515 （L87-4515） 150（5.9）
0.34 250
LW-18B-4530 （L87-4530） 1.8 N1 （49.8） 250 （19.8） 300（11.8） 210（7.4） 185（7.3） 570（1.25）
45
LW-18B-4550 （L87-4550） 500（19.7）
LW-18B-9015 （L87-9015） 150（5.9）
LW-18B-9030 （L87-9030） 300（11.8） 640（1.41）
90
LW-18B-9050 （L87-9050） 500（19.7）

● Type of feed: pressure feed ●All models, fluid nipple: G1/4, air nipple: G1/4

Ceramic spray gun Both fluid nozzles and tips of fluid needles are
made of tungsten carbide.

WA-200-ZP
automatic
gun
W-200-ZP
hand gun

Fluid Air Fluid Pattern Required

nozzle consumption output width Applied air Mass
Model orifice air cap compressor
　/min
φmm 　（cfm） m /min. mm（inch） kW g（lbs）

WA-200-201ZP 2.0 500 370 500

760 R1Z 2.2～3.7
（17.7） （14.6） （1.1）
WA-200-251ZP 2.5
W-200-201ZP 2.0 500 370 390 ●Usage
760 R1Z 2.2～3.7
（17.7） （14.6） （0.86） Most suitable for spraying ceramic enamels, abrasives
W-200-251ZP 2.5
and similarly abrasive fluids.
● Type of feed: pressure feed ●Spray distance: 250mm（19.8 inch）
● Atomizing air pressure: 0.34MPa（3.5kgf/cm2/50psi）●Pattern shape: straight
● Fluid nipple: G3/8 (PF3/8), air nipple: G1/4（PF1/4）

23
Round pattern gun
Most suitable for spraying miniature models,
cloth prints, arts and crafts,
do-it-yourself items, dyes, etc.

RG-3L
PC-51
cup
(option)

Fluid Atomizing Air Fluid Pattern Required

Spray Mass
Previous Type of nozzle air pressure consumption output width air compressor
Model distance Standard cup
model feed orifice
φmm mm（inch） MPa（psi） 　/ min（cfm） m /min. mm（inch） kW g（lbs）

RG-3L-1 RG-2-1 0.4 15 25（1.0） Gravity feed cup

200 30（1.1） 180～200
0.24 0.2～0.75 PC-51（220ml）
RG-3L-2 RG-2-2 Gravity 0.6 （7.9） （35.6） 35 35（1.4） （0.40～0.44）
PC-61（130ml）
RG-3L-3 RG-2-3 1.0 50（1.8） 80 35（1.4）

※ RG-3L1 with air adj. set is available.

Heavy viscosity spray gun

For applying special
high-viscosity paint,
adhesives, etc.

W-2001-1 W-2003
PC-19B PC-19B
pressure feed pressure feed Fluid nozzle and fluid needle
container container are made of stainless steel
(option) (option) which permits spraying of
even water borne adhesives.

Fluid Spray Atomizing Air Fluid Required

nozzle Pattern air Standard Mass
Model Name Type of feed distance air pressure consumption output width Main application
orifice compressor container
φmm mm（inch） MPa（psi） 　/min（cfm） m /min. mm（inch） kW g（lbs）

W-2001-1 2.5 （25W）170

0.29 （6.0） Pressure feed container: Construction wall paint,
Spray gun Pressure feed 200（7.9） （42.7） － － 0.75～3.7 450（0.99） small job
（10W）100 PC-19B（1000ml）
W-2001-2 3.0 （3.5）
200～300 0.29 300～400 Pressure feed container:
W-2003 High viscosity gun Pressure feed 2.0
（7.9～11.8） （42.7） 270（9.5） －
（11.8～15.7）
1.5 PC-19B（1000ml） 390（0.86） High viscosity paint

Disheveled gun
For spraying disheveled and
spattering patterns using special
air caps . Air

Type of feed : pressure feed type Disheveled pattern Paint

Fluid nozzle orifice: φ0.7mm
SGD-71
2
Atomizing air pressure: 0.2Mpa（2.0kgf/cm .28psi）
Air consumption: 75 liters/min.（2.6cfm）
Fluid output : 80 ml/min. Air

Required compressor: 0.4kW

Approx. mass : 1000g（2.2lbs）
with PC-17R（400 ml）pressure attached Spattering pattern Paint
feed container

24
 HP-AH HP-BH HP-CH

HP-CP HP-SBP HP-BC1P

HP-BE1 HP-E1

HP-BS HP-CS HP-SBS HP-BCS

HP-AR HP-CR HP-SAR HP-TR1

Fluid nozzle Atomizing Air Mass

Model air pressure consumption Standard
Type of feed orifice container or cup Applied materia
φmm MPa （psi） 　/ min
（cfm） g
（lbs）

0.2 14 0.4 84
Hi-Line Gravity 0.2 11 1.5 87
0.3 11 7 109
0.2 14 0.4 75
High Gravity 0.2 11 1.5 81
Performance 0.2 11 1.5 92
Plus 0.3 11 7 109
0.3 11 20 150
Suction
0.4 11 20 150
Gravity 0.6 32 40 236
High 0.8 47 40 236
Performance 0.6 32 40 254
Suction 0.10～0.29
0.8 47 40 261
（14.2～42.7）
0.3 20 1.5 90
Gravity 0.3 20 7 116
Eclipse
0.3 20 1.5 105
Suction 0.5 20 28 96
0.3 14 0.4 75
Gravity 0.3 14 1.5 82
0.5 20 7 115
Revolution Suction
0.5 20 28 90
0.5 20 28 100
0.3 14 7 150
Gravity
0.5 20 15 160

High Line

High
Performance
Plus

Eclipse

Revolution

25
Oil-less compressors for airbrushes

IS-875HT/925HT • Available150W single cylinder and 220W two cylinders models with air tank
• Auto shut off
Powerful and compact • Equipped with pressure switch as standard
Reliable IS-875HT IS-925H
Model
（Smart Jet Plus） （Smart Jet Plus）
Motor W 150/200 220/290
Max pressure MPa 4.2 4.2
Air consumption ℓ/min 15 23
Mass kg 5.5 7.1
Dimensions mm 280×160×275 280×160×3
Filter Regulator/3m Braided hose（HPA-BH31）/
Included Accessories
Airbrush holder　
Remarks:In the above dimensions not included accessorises

IS-875/925 • Available in 91 W single cylinder and 125 W two cylinder version

• Compact design
• Silent
• Equipped with pressure switch as standard
IS-875 IS-925
Model
(Smart Jet Pro) (Power Jet Lite)
Motor W 91 125
Max pressure MPa 3.1 4.2
Air consumption ℓ/min 6.0 13
Mass kg 6.4 7.9
Dimensions mm 156×310 ×260
Included Accessories 3m air hose（HPA-SH32）
Remarks:In the above dimensions not included accessorises

IS-850 • Compact design

• Silent
• Equipped with pressure switch as standard

Model IS-850

Motor W 91
Max pressure MPa 3.0
Air consumption ℓ/min 5
Mass kg 3.8
Dimensions mm 272×194×162
4m Coil hose（HPA-CH41）/
Included Accessories 3m air hose（HPA-SH31）/
Filter set
Remarks:In the above dimensions not included accessorises

IS-50 • Compact design

• Light weight（2.9Kg）
• Equipped with release valve

Model IS-50

Motor W 85
Max pressure MPa 3.5
Air consumption ℓ/min 4.5
Mass kg 2.6
Dimensions mm 150×150×180
Included Accessories 4m Coil hose（HPA-CH41）
Remarks:In the above dimensions not included accessorises

IS-976MB • Maintenance-free, oil-less two pole motor air compressor

• Case-mounted air regulator and moisture filter
• Dual manifold air regulator with airbrush and spray gun holders
• 2.5 liter air storage tank and internal cooling fan
• Equipped with pressure switch as standard
• Easy-to-setup

Model IS-976MB

Motor W 115/145
Max pressure MPa 0.4
（Accessories not included） Air consumption ℓ/min 12
Mass kg 12
Dimensions mm 360×200×640
Air Tank Capacity 2.5
Filter Regulator/3m Braided hose（HPA-BH32）/
Included Accessories
Airbrush holder
Remarks:In the above dimensions not included accessorises
※Applicable power supply voltage is AC100V.
※Modify the product so that it can be used with different voltage.

26
 Automotive refinishing spray guns
with agitator and Touch-up spray guns
Effective refinishing from small Can coat well with two-coat pearl, metallic,
to medium blemishes solid and clean paints as well as three-coat pearl paints

image

W-101A W-101A
-134G -134S

Fluid nozzle Atomizing Air Required Mass

Type of orifice air pressure consumption Pattern High General Applied air compressor
Model width air cap Application
feed φmm MPa（psi） 　/ min（cfm） mm（inch） atomization atomization model kW g（lbs）

Automotive refinishing spray guns

W-101A-104G 140（5.5）
Gravity
695
W-101A-134G 0.15 165 （1.53） Paint for Automotive
（22.8） （5.8） 120（4.7） refinishing
Suction 775
W-101A-134S （1.71）
Touch-up spray guns

W-101T-104G 140（5.5）
Gravity 0.15 165 335 Paint for Automotive
W-101T-134G （22.8） （0.74）
（5.8） refinishing
120（4.7）
W-101T-134S Suction

＊ 1. Pattern width is measured with 16 sec. (12sec/NK-2) paint viscosity and 60ml/min. fluid output.
● Spray distance: 200mm (7.9inch) for all models
● Atomizing air pressure at inlet of spray gun with trigger pulled and air flowing.
● All models: Fluid nipple - G1/4, air nipple - G1/4

Rotary type local pressure gauge

This product can increase coating job
efficiently through air pressure control.
This is a cheater valve that can indicate air pressure
Small-sized pressure gauge maintains
at inlet joint of spray gun. It’
s easy to use per straight
balance well when it is attached to your
shape and easy to fine adjust pressure per screw
spray gun.
valve.
Local air pressure control can promise
Compact and light valve can make spray man handle
stable air supply to your coating job.
spray gun easy.
Model: AJR-02L-VG Mass:95g
Model: AJR-02S-VG Mass:120g
AJR-02S-VG Adjusting system:Cylinder type
Connection: air nipple G1/4 AJR-02L-VG
Connection: air nipple G1/4

Aqua Gun Holder for L type Rotary Joint

Center Cup Gravity Feed Spray GunsGun
Can be installed anywhere since Allows you to handle hoses easily by
it is equipped with pedestal. rotating joint seat.
Can be installed with air hose at- Reduces failure cost by preventing air
tached for use with wall-mounting hose from contacting coating surface
type during coating application.
Applicable spray guns:LPH-300／ Hoses do not interfere with you when
W-300／LPH-400／W-400 coating in trunk room, doors, knee room or
Model: GH-WH-02 Mass:510g underbody of cars.
Model: AJR-02L Mass:46g AJR-02L
Gun Stand Gun Stand
GH-WH-02 (for horizontal (for wall mounting)
installation)

27
Air duster/Blow gun/Engine cleaner

Air duster Air duster

AG-6 AG-61

Flexible
extension
pipe
Example：Flexible
extension pipe is
attached.

Blow gun
Blow gun AG-41B
AG-4B

Flexible extension pipe

Model Lengthmm（inch） Mass g（lbs） Engine
ADP-150F 150（5.9） 30（0.07） cleaner
ADP-300F 300（11.8） 42（0.09） EC-3B
ADP-500F 500（19.7） 60（0.13）
Option for AG-6、AG-61

Fluid nozzle Atomizing Air Required Mass

Model Name orifice air pressure consumption air compressor Connection Usage
φmm MPa（psi） 　/ min（cfm） kW g（lbs）

AG-6
Air duster 1.7 0.34（49.9） 105（3.7） 0.4 185（0.41） G1/4（PF1/4） For blowing off dust, sludge, etc.
AG-61
AG-4B 218（0.48） G3/8（PF3/8）
Blow gun 4.5 0.59（85.3） 970（34.3） 1.5～5.5 For blowing off dust, sludge, etc.
AG-41B 212（0.47） G1/4（PF1/4）
EC-3B Engine cleaner 2.7 0.34（49.8） 40（1.4） 0.2 380（0.84） G1/4（PF1/4） For cleaning engines, machines, etc.

Aqua Dry Gun Aqua Dry Gun

Stand Unit

Able to amplify a small amount of air

and emit a large amount of air.
Most suitable for water-based paints
which dry slowly. Available 2 Aqua dry guns(including)
It can be used to dry solvent-based and fixed setting.
paints. Model: ADGS-1UB
Plastic grip is suitable for Anest Fixed setting area
Iwata spray guns with soft texture. Height : 0～2000mm
The valve below is recommended for Angle: 0～360°
local on-off operation. 1. Stand set 1 set
With air valve to adjust on-off at ADG-1BV 2. Aqua dry gun 2 guns ADGS-1UB
hand. 3. Air hose 2 pcs
Model：ADG-1BV Mass：400g 4. Quick joint 2 sets

28
 Containers, Cups & Paint
Gravity feed cup Free-angle cup
Supply Equipment PC-400S-2LF（Stainless）
PC-400A-2LF（Alminum）
PC-400S-2LTF（Stainless）
Suction feed container PC-250S-2LF（Stainless）
PC-150S-2LF（Stainless）
gun（option）

Pressure feed container

PCL-7B-2 PCL-10B-2
PCL-7B-3 PCL-10B-3

PC-1
PC-3 PC-2 PC-1S PCG-2D-1 PC-G400P-2
PC-18D PC-19B PC-19R

Select appropriate paint supply ②Suction feed container（400～1000ml） and diaphragm paint pumps are most
equipment in accordance with paint for medium-size painting jobs suitable for continuous painting jobs
consumption and painting job. ③Pressure feed container（1000～2000ml） such as on production lines, automatic
①Side mount gravity feed cup（130～ for medium-size jobs using pressure painting machines and painting robots
600ml）for touch-ups and small painting feed spray gun at the plant.
jobs ④Paint pressure tanks （10～80 liters）

Model Capacity m Mass g（lbs） Connection Applicable spray gun

Suction feed container
PCL-7B-2 700 370（0.81） G1/4（PF1/4） W-101、-71、-61、LPH-101
PCL-7B-3 700 375（0.82） G3/8（PF3/8） W-200、-77
PCL-10B-2 1000 410（0.90） G1/4（PF1/4） W-101、-71、-61、LPH-101
PCL-10B-3 1000 415（0.91） G3/8（PF3/8） W-200、-77
PC-1 1000 335（0.74） G3/8（PF3/8） W-200、-77
PC-1S 1000 330（0.73） G1/4（PF1/4） W-101、-71、-61、LPH-101
PC-2 600 270（0.59） G1/4（PF1/4） W-101、-71、-61、LPH-101
PC-3 400 180（0.40） G1/4（PF1/4） W-101、-71、-61、LPH-101
Gravity feed cup（Side）
PC-4 400 180（0.40） G3/8（PF3/8） W-200、-77
PC-4S 400 168（0.37） G1/4（PF1/4） W-50、-101、LPH-50、-101、W-71、-61、RG-3L
PC-400A-2LF 400 125（0.28） G1/4（PF1/4） W-50、-101、LPH-50、-101、W-71、-61、RG-3L, 　free-angle stainless steel cup
free-angle, stainless steel cup
PC-400S-2LTF 400 210（0.46） G1/4（PF1/4） W-50、-101、LPH-50、-101、W-71、-61、RG-3L, 　
fluorine-coated
PC-400S-2LF 400 210（0.44） G1/4（PF1/4） W-101、LPH-101、W-71、-61　free-angle stainless steel cup　
PC-250S-2LF 250 170（0.37） G1/4（PF1/4） W-50、-101、LPH-50、-101、W-71、-61、RG-3L　free-angle stainless steel cup
PC-150S-2LF 150 155（0.34） G1/4（PF1/4） W-50、-101、LPH-50、-101、W-71、-61、RG-3L　free-angle stainless steel cup
PC-5 250 135（0.30） G1/4（PF1/4） W-50、-101、LPH-50、-101、W-71、-61、RG-3L
PC-51 220 126（0.28） G1/4（PF1/4） W-50、-101、LPH-50、-101、W-71、-61、RG-3L　stainless steel cup
PC-61 130 110（0.24） G1/4（PF1/4） W-50、-101、LPH-50、-101、W-71、-61、RG-3L　stainless steel cup
PCG-6P-2 600 220（0.48） G1/4（PF1/4） W-101、LPH-101、W-71、-61 plastic cup
PCG-6P-3 600 227（0.50） G3/8（PF3/8） W-200、-77 plastic cup
Gravity feed cup（Center）
PCG-6P-M 600 160（0.35） M16×1.5（female） W-400、LPH-400 plastic cup
PCG-2P-2 200 100（0.22） G1/4（PF1/4） W-300、LPH-300 plastic cup
PCG-2D-1 150 100（0.22） G1/8（PF1/8） LPH-80, Alminum cup
PC-G400P-2 400 158（0.35） G1/4（PF1/4） W-300、W-300WB、LPH-300 plastic cup
Pressure feed container
PC-17R 400 564（1.24） G1/4（PF1/4） SGD-71 disheveled gun Max. operating pressure 0.20MPa（2kgf/cm2/28.4psi）
PC-18D-S0 2000 1250（2.76） G3/8（PF3/8）fluid outlet various spray guns Max. operating pressure 0.34MPa（3.5kgf/cm2/49.8psi）
PC-18DT-S0 2000 1200（2.65） G3/8（PF3/8）fluid outlet various spray guns Max. operating pressure 0.34MPa（3.5kgf/cm2/49.8psi）
PC-19B 1000 470（1.04） M16×1（male） W-2001-1 W-2003 Max. operating pressure 0.49MPa（5kgf/cm2/71.1psi）
PC-19R 1000 830（1.83） G3/8（PF3/8） W-200 W-77 Max. operating pressure 0.27MPa、
（2.8kgf/cm2/39.8psi）

Paint pressure tank Diaphragm paint Handy paint pump

They are equipped with either a pump *Paint pump with 5 liter hopper for small
manual or an automatic mixer to You can change paint painting jobs.
prevent paint from precipitating. color or replenish paint *Easy to transport（8kg）.
10-80 liter paint tanks are available. by simply putting intake *Double-acting type without pulsation
hose set into a new can can always supply stable fluid output.
About the use of paint pressure of paint. ◎Small painting jobs such as metal,
tanks overseas
Codes and standards for pressure
This method simplifies resin and woodwork
vessels vary from country to country. paint feed system and ◎Designated color line painting such as
Please contact us to see if our paint saves work. metal, resin and woodwork
pressure tanks apply to your country ◎Moving jobs of construction painting
specification for pressure vessels.
such as shutters or indoor decorations
※ For details, refer to
29 ※ For details, refer to "Paint supply PT-20DM 「Paint supply pumps & ※ For details, refer to「Paint supply pumps &
pumps &system equipment"catalog. （with automatic mixer） system equipment」catalog. DPS-90E system equipment」catalog. HDP-705C
 12mm

8.7mm

12mm 8.7mm 8.7mm

0.49MPa

B
B
B
B

30
 E-spray series
We have realized a high level of safety.
■ No insulation device is required in fluid supplying route.
■ We chose Internal cascade type with a high level of safety comparing with external cascade type.

Manual electrostatic spray gun for water-based paint Manual electrostatic spray gun
（indirect charge and internal cascade type） （direct charge and internal cascade type）

E-M15C：for general paints E-M10C：for water-based and

low-resistance paint

Please request catalog of

“Electrostatic painting spray
International equipment” . If you have
Patents some questions, please
Pending contact our branch where
locates near you.
E-MW100

■ For operation
Safety precautions 1. Never use these spray guns for purposes other than coating jobs.
2. Before use, be sure to carefully read the instruction manual for correct usage.
3. Never alter these products for any application. If done, it can cause poor performance and failure.
■ Others
1. Figures in this catalog are measured by our test paints.
　They will differ according to kinds of paints and painting conditions.

● Models, specifications and photos are subject to change without notice.

ANEST IWATA Corporation

3176, Shinyoshida-cho, Kohoku-ku,
Yokohama 223-8501, Japan
Tel: 045-591-1118 Fax: 045-591-1137
http://www.anest-iwata.co.jp/

Printed in Japan CAT.No. SE-68F 201402.改.5.NP★