WM230 Quick Start Guide

V1.0 2017.11

Aircraft

The WM230 featuring a fully stabilized camera, Intelligent Flight Modes and Obstacle Avoidance
inside an upgraded revolutionary folding design. It captures 4K videos and 12 megapixel photos,
and is capable of both ActiveTrackTM and TapFlyTM making complex shots effortless. WM230 boasts
a maximum flight speed of 42.5 mph (68.4 kph) and a maximum flight time of 22 minutes.

1. Forward Vision System

2. Gimbal and Camera
3. Propellers
4. Motors
5. Front LEDs
6. USB Type-C Port
7. Downward Vision System
8. Backward Vision System
9. Antennas
10. Camera Micro SD Card Slot
11. Aircraft Status Indicator
12. Intelligent Flight Battery
13. Power Button
14. Battery Level LEDs

** Maximum flight time was tested in 0 wind at a consistent 15.5 mph (25 kph). This value should
be taken for reference only.
** The Forward and Backward Vision Systems are affected by surrounding conditions. Read the
Disclaimer and Safety Guidelines and watch the tutorial in the DJI GOTM 4 app or on the Official DJI
website to learn more.

Remote Controller

The Remote Controller offers a maximum transmission range of 2.49 mi (4 km). Video from the
aircraft to the DJI GO 4 app on your mobile device at up to 1080p at close range, and 720p at longer
ranges. The WM230 can also be flown by phone only.

1. Flight Mode Switch

2. Function Button
3. Control Sticks
4. Antennas
5. Power Button
6. Mobile Device Clamp
7. Charging Port (USB Type-C)
8. Flight Pause Button
9. RTH Button
10. Status LED
11. Battery Level LEDs
12. Gimbal Dial
13. Customizable Button
14. Record Button
15. Shutter Button

The remote controller is able to reach its maximum transmission distance (FCC) in a wide open
area with no Electro-Magnetic Interference, and at an altitude of about 400 feet (120 meters).

Specifications

 Aircraft (Model: U11X)

Weight 430 g
Max Speed 42.5 mph (68.4 kph) in Sport Mode without wind
Max Flight Time 22 minutes (0 wind at a consistent 15.5 mph (25 kph))
Operating Temperature 32° to 104° F (0° to 40° C)
Satellite Positioning Systems GPS+GLONASS
Operating Frequency 2.4-2.4835 GHz; 5.725-5.850 GHz*
Transmitter Power (EIRP) 2.4G: 28 dBm (FCC), 18 dBm (CE), 18 dBm (SRRC)
5.8G: 32 dBm (FCC), 13 dBm (CE), 30 dBm (SRRC)
● Gimbal
Controllable Range Pitch: -90° to +0° (Default settings), -90° to +22° (Customized)
● Camera
Sensor CMOS
Max Image Size 4000×3000
Still Photography Modes Single shot, Burst shooting
Video Recording Modes 3840×2160
Video Storage Bitrate 100 Mbps
Video MP4
Supported SD Cards microSD
● Remote Controller (Model: S01A)
Dimensions 144x78x62 mm
Operating Frequency 2.4-2.4835 GHz; 5.725-5.850 GHz*
Max Transmission Distance 2.4G FCC: 2.5 mi (4 km); CE/SRRC: 0.6 mi (1 km)
5G FCC: 2.5 mi (4 km); CE: 0.4 mi (0.6 km); SRRC: 0.6 mi (1 km)
Unobstructed and free of interference.
Operating Temperature 32° to 104° F (0° to 40° C)
Battery 2970 mAh
Transmitter Power (avg. EIRP) 2.4G: 26 dBm (FCC), 18.87 dBm (CE), 18 dBm (SRRC)
5.8G: 30 dBm (FCC), 13.52 dBm (CE), 26 dBm (SRRC)
Operating Voltage 1000 mA @ 3.7 V
Supported Mobile Device Size Thickness supported: 6.5 - 8.5 mm, Max length: 160 mm
Supported USB port types Lightning, Micro USB (Type-B), USB Type-CTM
● Charger
Voltage 13.2 V
Rated Power 50 W
● Intelligent Flight Battery
Capacity 2375 mAh
Voltage 11.55 V, Max 13.2 V
Battery Type LiCo02
Energy 27.43 Wh
Net Weight Approx. 0.3 lbs (140 g)
Charging Temperature Range 41° to 104° F (5° to 40° C)
Max Charging Power 60 W

*To comply with local regulations, the operation frequency of 5.8GHz is not available in some
countries.

Download the DJI GO 4 App and Watch the Tutorial Videos

Search for ‘DJI GO 4’ on the App Store or Google Play, or scan the QR code to download the app on
your mobile device. Watch the tutorial videos at www.dji.com or in the DJI GO 4 App.

Charge the Batteries

Remove Intelligent Flight Battery

Charge the batteries
1. Connect the charger to power outlet
2. Connect the charger to Intelligent Flight Battery
3. Connect the Remote controller to the charger

Check the Battery Levels

Press once to check the battery level. Press once, then again and hold to turn on/off.

Press the Power button once to check the current battery level. Press once, then again and hold to
turn on/off the remote controller.

Prepare the Remote Controller

Unfold the antennas and the mobile device clamp

 Place one end of the RC cable to the end of the slot

Attach mobile device

Prepare the Aircraft

1. Remove the gimbal clamp from the camera

2. Unfold the rear arms

3. Unfold the front arms

4. Unfold the landing gear

Prepare for Takeoff

1. Power on the remote controller

2. Power on the aircraft

3. Launch the DJI GO 4 App

Flight

• Takeoff/Landing
Before taking off, make sure the Aircraft Status Bar in the DJI GO 4 app displays ‘Ready to Go’

• Remote Controller Operation

• Controlling flight with Virtual Joysticks on your mobile device via Wi-Fi

1. Toggle the Control Mode Switch to turn on Wi-Fi

2. Power on the aircraft
3. Launch the DJI GO 4 app and tap the icon on the top right of your screen, then scan the Wi-
Fi QR Code on the front arm to start connection
4. Tap Auto Takeoff
5. Fly the aircraft with touch control

• In the DJI GO 4 App

Fly Safe
Compliance Information
FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

The Aircraft and Remote controller complies with FCC radiation exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits,
human body proximity to the Aricraft antenna shall not be less than 20cm during normal operation.

RSS Warning
This device complies with ISEDC licence-exempt RSS standard (s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.

Radiation Exposure Statement:

The Aircraft and Remote Controller complies with RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The Aircraft should be installed and operated with minimum distance 20cm between the
radiator& your body.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
For Remote controller, SAR tests are conducted using standard operating positions accepted by the FCC/ISEDC with the
device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined
at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value.

Before a new model device is a available for sale to the public, it must be tested and certified to the FCC that it does not
exceed the exposure limit established by the FCC/ISEDC, Tests for each device are performed in positions and locations
(e.g. at the ear and worn on the body) as required by the FCC/ISEDC.

For body worn operation, this model device has been tested and meets the FCC/ISEDC RF exposure
guidelines when used with an accessory designated for this product or when used with an accessory that
Contains no metal and that positions the handset a minimum of 10 mm from the body.

Non-compliance with the above restrictions may result in violation of RF exposure guidelines.

KCC Warning Message

“해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는
할 수 없습니다.”
“해당 무선설비는 운용 중 전파혼신 가능성이 있음”
NCC Warning Message
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，
應改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功
率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in
compliance with the essential requirements and other relevant provisions of the Directive
2014/53/EU.
A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance

EU contact address: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany

Declaración de cumplimiento UE: SZ DJI TECHNOLOGY CO., LTD. por la presente declara que este
dispositivo cumple los requisitos básicos y el resto de provisiones relevantes de la Directiva
2014/53/EU.
Hay disponible online una copia de la Declaración de conformidad UE en www.dji.com/euro-
compliance

Dirección de contacto de la UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany

EU-verklaring van overeenstemming: SZ DJI TECHNOLOGY CO., LTD. verklaart hierbij dat dit
apparaat voldoet aan de essentiële vereisten en andere relevante bepalingen van Richtlijn
2014/53/EU.
De EU-verklaring van overeenstemming is online beschikbaar op www.dji.com/euro-compliance

Contactadres EU: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany

Declaração de conformidade da UE: A SZ DJI TECHNOLOGY CO., LTD. declara, através deste
documento, que este dispositivo está em conformidade com os requisitos essenciais e outras
disposições relevantes da Diretiva 2014/53/EU.
Existe uma cópia da Declaração de conformidade da UE disponível online em www.dji.com/euro-
compliance

Endereço de contacto na UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany

Dichiarazione di conformità UE: SZ DJI TECHNOLOGY CO., LTD. dichiara che il presente dispositivo
è conforme ai requisiti essenziali e alle altre disposizioni rilevanti della direttiva 2014/53/EU.
Una copia della dichiarazione di conformità UE è disponibile online all'indirizzo Web
www.dji.com/euro-compliance

Indirizzo di contatto UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany

Déclaration de conformité UE : Par la présente, SZ DJI TECHNOLOGY CO., LTD déclare que cet
appareil est conforme aux principales exigences et autres clauses pertinentes de la directive
européenne 2014/53/EU.
Une copie de la déclaration de conformité UE est disponible sur le site
www.dji.com/euro-compliance

Adresse de contact pour l'UE : DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany

EU-Compliance: Hiermit erklärt SZ DJI TECHNOLOGY CO., LTD., dass dieses Gerät den wesentlichen
Anforderungen und anderen einschlägigen Bestimmungen der EU-Richtlinie 2014/53/EU
entspricht.
Eine Kopie der EU-Konformitätserklärung finden Sie online auf www.dji.com/euro-compliance.

Kontaktadresse innerhalb der EU: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE

OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the
residual waste, but have to be disposed of separately. The disposal at the communal
collecting point via private persons is for free. The owner of old appliances is
responsible to bring the appliances to these collecting points or to similar collection
points. With this little personal effort, you contribute to recycle valuable raw materials
and the treatment of toxic substances.

Thailand Warning message

เครื่ องโทรคมนาคมและอุปกรณ์น้ ี มีความสอดคล้องตามข้อกาหนดของ กทช.
Mexico Warning message
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este
equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar
cualquier interferencia, incluyendo la que pueda causar su operación no deseada.”

Brazil Warning message

Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra
interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a
sistemas operando em caráter primário