BRITISH STANDARD BS 1414:

1975
Incorporating
Amendment Nos. 1
and 2

Specification for

Steel wedge gate valves

(flanged and
butt-welding ends) for
the petroleum,
petrochemical and
allied industries

UDC 621.646.5:669.14:[622.313 + 662.753 + 665.6]

BS 1414:1975

Co-operating organizations

The Petroleum Equipment Industry Standards Committee, under whose

supervision this British Standard was prepared, consists of representatives
from the following Government departments and scientific and industrial
organizations:

British Gas Corporation

British Mechanical Engineering Confederation
British Rubber Manufacturers’ Association Ltd.
British Steel Industry*
Council of British Manufacturers of Petroleum Equipment*
Department of Energy (Oil)
Oil Companies Materials Association*
Process Plant Association

The organizations marked with an asterisk in the above list, together with the
following, were directly represented on the committee entrusted with the
preparation of this British Standard:

Association of Hydraulic Equipment Manufacturers

British Chemical Engineering Contractors’ Association
British Industrial Measuring and Control Apparatus Manufacturers’
Association
British Plastics Federation
British Ship Research Association
British Valve Manufacturers’ Association
Engineering Equipment Users’ Association
Steel Castings Association

This British Standard, having

been approved by the
Petroleum Equipment
Industry Standards
Committee, was published
under the authority of the
Executive Board on
30 April 1975

© BSI 08-1999

First published January 1949

First revision June 1954 Amendments issued since publication
Second revision March 1960
Third revision April 1975 Amd. No. Date of issue Comments

The following BSI references 5837 June 1988

relate to the work on this
standard: 6562 August 1990 Indicated by a sideline in the margin
Committee reference PSE/7
(formerly PEE/1)
Draft for comment 71/37781 DC

ISBN 0 580 08991 6

 BS 1414:1975

Contents

Page
Co-operating organizations Inside front cover
Foreword iii
Section 1. General
1 Scope 1
2 References 1
3 Nomenclature 1
4 Pressure classification 1
5 Pressure/temperature ratings 1
6 Nominal sizes 1
7 Information to be supplied by the purchaser 4
Section 2. Design
8 Body 4
9 Bonnet 7
10 Wedge 7
11 Yoke 8
12 Handwheel and handwheel nut 8
13 Stem and yoke sleeve 8
14 Stuffing box, packing and lantern ring 9
15 Bolting 9
16 Operation 9
17 Bypass 11
18 Soft seal rings 11
Section 3. Materials
19 Shell 11
20 Body seat rings 11
21 Bonnet gasket 11
22 Wedge 11
23 Yoke 11
24 Handwheel or chainwheel 11
25 Handwheel or chainwheel nut 11
26 Yoke sleeve 11
27 Yoke sleeve retaining nut 11
28 Gland 12
29 Trim 12
30 Lantern ring 12
31 Stem packing 12
32 Bolting 12
33 Plugs 12
34 Nameplate 12
35 Soft seals 12
36 Special applications 12
Section 4. Marking
37 Required markings 12
38 Body and nameplate markings 12
39 Body and bonnet markings 14
40 Nameplate markings 14
41 Additional markings 14
42 Omission of markings 14

© BSI 08-1999 i
BS 1414:1975

Page
Section 5. Testing
43 Production pressure testing 14
Section 6. Shipping
44 Preliminary 15
45 Preparation for despatch 15
46 Packaging 15
Appendix A Particular dimensions for each class of valve 16
Appendix B Application to piping systems with BS 4504 flanges 20
Figure 1 — Solid wedge gate valve, outside screw and yoke rising
stem, cast or forged steel 2
Figure 2 — Butt-welding ends 5
Figure 3 — Location of tappings 6
Table 1 — Stuffing box bore and packing width 10
Table 2 — Trim materials, hardness and acceptable specifications 13
Table 2a — Test durations 14
Table 3 — Dimensions of Class 150 valves 16
Table 4 — Dimensions of Class 300 valves 17
Table 5 — Dimensions of Class 400 valves 17
Table 6 — Dimensions of Class 600 valves 18
Table 7 — Dimensions of Class 900 valves 18
Table 8 — Dimensions of Class 1 500 valves 19
Table 9 — Dimensions of Class 2 500 valves 19
Table 10 — Nominal pressure and class ratings and nominal
size range 20
Publications referred to Inside back cover

ii © BSI 08-1999
 BS 1414:1975

Foreword

This British Standard is one of a series for valves prepared under the authority
of the Petroleum Industry Standards Committee. It was first published in 1949
when the materials referred to were described by reference to ASTM
specifications. It is a metricated revision except that class designations and body
to bonnet bolting sizes have not been converted into metric units. Imperial units
are also given for some dimensions in order to comply with established
international petroleum practice. The previous sections dealing with face-to-face
and end-to-end dimensions, inspection and tests have now been omitted as these
subjects have their own separate standards:
BS 2080 “Face-to-face, centre-to-face, end-to-end and centre-to-end dimensions
of flanged and butt-welding end steel valves for the petroleum, petrochemical
and allied industries”.
BS 6755 “Testing of valves” Part 1 “Specification for production pressure
testing requirements.
NOTE Requirements for final inspection and supplementary inspection at all stages of manufacture,
previously specified in BS 5416-1:1974 (now withdrawn) should be stated by the purchaser in his
enquiry or order.
The end flanges for valves of 600 mm (24 in) size and below are required to be in
accordance with BS 1560 “Steel pipe flanges and flanged fittings (nominal
sizes ½ in to 24 in) for the petroleum industry” — Part 2 “Metric dimensions”
(corresponding to ANSI B 16.5) and butt-welding ends are generally in
accordance with ANSI B 16.25. For valves larger than 600 mm (24 in) size, end
flanges are required to be in accordance with BS 3293 “Carbon steel pipe flanges
(over 24 in nominal size) for the petroleum industry” or API Standard 605.
NOTE User requirements for valves generally in accordance with this standard but suitable for use
in piping systems with flanges in accordance with BS 4504 “Flanges and bolting for pipes, valves and
fittings. Metric series” are dealt with in Appendix B.
It is intended that valves complying with the requirements of this standard
should be interchangeable as units with those of similar type specified in API 600.
The present revision of BS 1414 is generally in accordance with the seventh
edition of API 600 (November 1973) except that it has been extended to cover
carbon steel valves in sizes up to 1 050 mm (42 in) in Class 150 and Class 300.
Acknowledgment is made to the American Petroleum Institute and to the
American National Standards Institute for data used.
The titles of the American standards referred to in this standard and the foreword
are as follows:
ANSI
B 16.5 Steel pipe flanges and flanged fittings (including supplements)
B 16.25 Buttwelding ends
API
Std 5b Specification for threading, gaging, and thread inspection of
casing, tubing and line pipe threads
Std 600 Steel gate valves (flanged or butt-welding ends)
Std 605 Large-diameter carbon steel flanges
ASTM
A 182 Forged or rolled alloy-steel pipe flanges, forged fittings and valves
and parts for high temperature service
A 276 Stainless and heat resisting steel bars and shapes
A 351 Ferritic and austenitic steel castings for high temperature service
B 124 Copper and copper alloy forging rod, bar and shapes
B 138 Manganese bronze rod, bar and shapes
B 148 Aluminium bronze sand castings
B 150 Aluminium bronze rod, bar and shapes
B 584 Copper alloy sand castings for general applications

© BSI 08-1999 iii

BS 1414:1975

A British Standard does not purport to include all the necessary provisions of a
contract. Users of British Standards are responsible for their correct application.

Compliance with a British Standard does not of itself confer immunity

from legal obligations.

Summary of pages
This document comprises a front cover, an inside front cover, pages i to iv,
pages 1 to 20, an inside back cover and a back cover.
This standard has been updated (see copyright date) and may have had
amendments incorporated. This will be indicated in the amendment table on the
inside front cover.

iv © BSI 08-1999
 BS 1414:1975

Section 1. General The numerals in these class designations represent

the primary service pressure ratings of the valves in
1 Scope pounds-force per square inch.
This British Standard specifies requirements for 5 Pressure/temperature ratings
cast or forged carbon and alloy steel outside screw
and yoke, solid wedge (plain or flexible) rising stem The pressure/temperature ratings applicable
gate valves, with or without soft seals, with flanged to valves specified in this standard shall be
or butt-welding ends, in nominal sizes within the in accordance with Tables PE-1 to PE-12 of
range of 25 mm to 600 mm (1 in to 24 in) and Appendix A of BS 1560-2:1970 for the particular
Class 150 to Class 2 500. It also covers carbon steel shell material specified. There is, however, a
valves in nominal sizes 650 mm to 1 050 mm (26 in temperature restriction on soft seals and on certain
to 42 in) in Class 150 and Class 300 only. This trim materials (see 18.3 and 29.5).
standard can also be used as a general guide where Where valves in accordance with this standard are
valves of material composition outside the scope of to be used at service temperatures below p 30 °C,
section three of this standard are required as, for reference should be made to BS 3351. Service
example, for use in highly corrosive services or temperature refers to the temperature of the fluid in
environments or for low temperatures the line at the valve.
(see clause 36).
6 Nominal sizes
2 References
This standard covers valves of the following nominal
The titles of the British Standards referred to in this sizes:
standard are listed on the inside back cover. mm (in) mm (in) mm (in)
25 (1) 150 (6) 500 (20)
3 Nomenclature
32a (1¼)a 200 (8) 600 (24)
For the purposes of this British Standard the 40 (1½) 250 (10) 650 (26)
nomenclature for valve parts shall be as shown in
50 (2) 300 (12) 700 (28)
Figure 1 which is also illustrative of some
acceptable designs. 65a (2½)a 350 (14) 750 (30)
80 (3) 400 (16) 900 (36)
4 Pressure classification 100 (4) 450 (18) 1 050 (42)
a
These sizes have been retained only for the purpose of replacing
This standard applies to valves of the following existing valves. Their use for new construction in piping systems
pressure class designations: using BS 1560-2 end flanges should be avoided.
Class 150, Class 300, Class 400, Class 600, For each valve class the applicable sizes are shown
Class 900, Class 1 500 and Class 2 500. in Appendix A.

© BSI 08-1999 1
BS 1414:1975

Figure 1 — Solid wedge gate valve, outside screw and yoke rising stem, cast or forged steel

2 © BSI 08-1999
 BS 1414:1975

View showing yoke with actuator mounting flange

Material Material
Reference Name of part reference Reference Name of part reference
clause clause
1 Body 19 22 Yoke sleeve retaining nut 27
2 End flange — 23 One piece gland 28
3 Butt-welding end — 24 Gland follower 28
4 Body bosses — 25 Gland flange 28
5 Body/bonnet flange — 26 Stem 29
6 Bonnet 19 27 Stem seat —
7 Bonnet flange — 28 Wedge facing ring 29
8 Shoulder seated ring 20 and 29 29 Back-seat bushing 29
9 Bottom seated ring 20 and 29 30 Back seat 29
10 Bonnet gasket 21 31 Lantern ring 30
11 Ring joint 21 32 Stem packing 31
12 Plain wedge 22 and 29 33 Wiper rings 31
13 Flexible wedge 22 and 29 34 Bonnet stud-bolts and nuts 32
14 Yoke 23 35 Gland bolt and nut 32
15 Actuator mounting flange — 36 Gland lug bolt and nut 32
16 Yoke cap — 37 Yoke bolting 32
17 Handwheel 24 38 Stuffing box plug 33
18 Handwheel nut 25 39 Nameplate 34
19 Yoke sleeve 26 40 Soft seal ring 35
20 Yoke sleeve rolling bearing — 41 Soft seal retaining ring 35
21 Bearing lubricator fitting — 42 Soft seal retaining ring 35
screws
NOTE These sketches are composite for the purpose of showing some typical variations in individual details and part names.
A product utilising any combination of these details (except when such combination may be specifically prohibited in the text)
or similar construction will be acceptable provided it complies with this standard in all other respects.
* See Appendix A.
† See Figure 2.

Figure 1 — Solid wedge gate valve, outside screw and yoke rising stem, cast or forged steel

© BSI 08-1999 3
BS 1414:1975

7 Information to be supplied by the o) Material(s) for bonnet, gland, and yoke bolting
purchaser if required for operation at process design
temperatures below p 30 °C or above 480 °C, or
Certain clauses of this standard permit alternatives for other special operating conditions
and the purchaser may require features which (see clause 32).
depart from the requirements of this standard. The
p) Material requirements for valves in highly
purchaser should state in the enquiry and order the
corrosive services or environment, or for low
following (the items marked with an asterisk are
temperature service (see clause 36).
mandatory).
q) Test and inspection requirements in
a) *Class and nominal size (see clauses 4 and 6
and B.7). accordance with BS 5146.
b) *If soft seals are required and, if so, whether r) Requirements for tropical or special packaging
(see clause 46).
these are required to be in the wedge seats or
body seats (see clauses 5 and 18).
Section 2. Design
c) *Whether flanged or butt-welding ends are
required. 8 Body
1) If flanged ends are required, whether
8.1 For the body the design criteria specified in 8.2
welded-on flanges are acceptable (see 8.5);
to 8.11 shall be observed.
the type of facing (see 8.6); for sizes
above 600 mm (24 in), whether flanges are to 8.2 The body shall be designed to minimize pressure
be in accordance with BS 3293 or API Std 605. loss as well as corrosive and erosive effects. The
body end ports shall be circular.
2) If butt-welding ends are required, the pipe
schedule number or wall thickness and outside 8.3 The wall thickness of the body shall conform to
diameter [see 8.8 b)]. the shell thickness given in Appendix A. Drilling of,
or pinning to, the wall of a pressure-containing part,
d) If allowance is to be made for the passage of a
e.g. for nameplate fixing, is not permissible where it
pipe scraper [see 8.8 c)].
would reduce the effective thickness below the
e) If shell tappings are required and, if so, the minimum permitted value.
location and the type of thread if other than API
8.4 Face-to-face dimensions for raised face flanged
Std 5B (see 8.9 and 9.8).
end valves and end-to-end dimensions for
f) If a particular form of wedge is required butt-welding end and ring joint flanged end valves
(see 10.2). shall conform to the dimensions specified in
g) If the yoke is to be fitted with a flange for BS 2080.
actuator or gearbox mounting (see clause 11). 8.5 End flanges shall be cast or forged integral with
h) Details of type of operation required if other the body except that flanges may be attached by
than direct-handwheel operated (see clauses 12 welding if so specified in the order. The welds of end
and 16). flanges attached by butt-welding shall comply with
i) If a lantern ring is to be provided for Class 300 the requirements of BS 3351 and shall have any
to Class 2 500 valves (see 14.4). necessary heat treatment as required by BS 3351 to
ensure that they are suitable for service
j) If a bypass is required, give the full
temperatures down to p 30 °C. Flange attachment
specification of the bypass valve, piping and by other welding processes shall be the subject of
connections (see clause 17). agreement between the manufacturer and the
k) *The shell material (see clause 19). purchaser.
l) If a special bonnet gasket is required 8.6 End flanges shall comply with the
(see clause 21). requirements of BS 1560-2 for valves up to and
m) *The nominal trim material symbol including 600 mm (24 in) nominal size and BS 3293
(see 29.2). or API Std 605 (as specified by the purchaser) for
n) If any special stem packing is required, or valves over 600 mm (24 in) nominal size. End flange
specify packing design temperature if facings shall be one of the types shown in
above 400 °C (see clause 31). Figures 1 and 2 of BS 2080. The purchaser shall
specify the type of facing required.
Valves generally in accordance with this standard
but suitable for use in piping systems with BS 4504
flanges shall comply with the requirements of
Appendix B.

4 © BSI 08-1999
 BS 1414:1975

8.7 Butt-welding ends shall comply with the details NOTE When welding butt-welding end valves into piping
shown in Figure 2. systems the welds and any necessary heat treatment shall
comply with the requirements of BS 3351.

NOTE 1 The inside and outside surfaces of valve welding ends shall be machine finished overall. Welding-end bores shall be
machined parallel for a distance of 1.5t and then run out as shown in the figures without abrupt change of section. The outsides
of welding ends may be run out in any manner indicated in the figures, provided that sharp angles and abrupt changes of slopes
are avoided.
NOTE 2 For nominal outside diameters and wall thicknesses of standard steel pipes see BS 1600-2.
NOTE 3 For valves required to connect with pipe of less than 4.8 mm wall thickness the angle 37.5 ± 2.5° shall not apply and
welding ends shall be finished to a slight chamfer or be square, at the option of the manufacturer.
NOTE 4 Regardless of tolerances specified for dimensions A and B, the thickness of the welding end shall never be less
than 87.5 % of the nominal thickness of the pipe.
NOTE 5 For end-to-end dimensions of butt-welding end valves see BS 2080.
Value mm 25 32 40 50 65 80 100 150 200 250 300 350 400 450 500 600 650 700 750 900 1 050
nominal
(in) (1) (1¼) (1½) (2) (2½) (3) (4) (6) (8) (10) (12) (14) (16) (18) (20) (24) (26) (28) (30) (36) (42)
size
A (mm) 35 44 50 62 75a 91 117 172 223 278 329 362 413 464 516 619 670 722 774 928 1 083
Tolerance on
+0
A (mm) –0.8
Tolerance on
± 0.8 ± 1.6 +3.2
B (mm) –1.6
a
A shall be 78 mm when used with BS 3600 steel pipe.

Figure 2 — Butt-welding ends

© BSI 08-1999 5
BS 1414:1975

8.8 For flanged valves the minimum inside diameter Provision should be made for the body tappings as
of the body end port shall be as specified in follows:
Appendix A. Nominal size Pipe tapping size Minimum
For butt-welding end valves the minimum inside diameter of boss
diameter of the body end port shall comply with the mm in mm
details given in Figure 2. Pipe schedule number or
pipe wall thickness and outside diameter of the pipe 50 to 100 ½ 38
shall be specified by the purchaser. 150 and 200 ¾ 44
If it is required to pass a pipe scraper through the 250 and 300 1 54
valve, this shall be specified by the purchaser. 350 and larger 1½ 70
8.9 Valves of nominal sizes 80 mm (3 in) and above Holes shall not be drilled or tapped unless specified
shall have provision for tappings at the seven in the order, which should then state the thread
positions A to G shown in Figure 3. When the metal required (if other than API Std 5B) and the location
thickness of the body is insufficient to provide the (see Figure 3). Tapped holes shall be provided with
effective length of the thread for body tapping, or the plugs.
body presents an uneven surface, bosses shall be
On valves of nominal sizes below 80 mm (3 in),
provided.
provision for tapping shall be as specified by the
purchaser and shall comply with Figure 3 as
regards location.
Where a bypass is to be provided see clause 17.

Third angle projection.

NOTE For valves below 80 mm the bonnet tapping may be positioned to suit the manufacturer.
Figure 3 — Location of tappings

6 © BSI 08-1999
 BS 1414:1975

8.10 Separate seat rings in the body shall be 9.3 The body to bonnet connection shall be flanged
employed except as indicated in a) and b) of this and the flange facings shall be male-and-female,
subclause. tongue-and-groove, or ring joint type, except for
a) Austenitic steel valves, in which case these Class 150 which may be a plain (flat) face.
may have integral seats. Where possible, body/bonnet flange facings and
b) Austenitic or hard-facing (body) seat materials gaskets shall be of standard dimensions in
which may be deposited directly on the valve body accordance with BS 1560-2, BS 3293 or
and the minimum finished thickness of the API Std 605.
deposit shall then be 1.6 mm. Direct deposition 9.4 Bonnet flanges and body/bonnet flanges shall be
of 13 % chromium seat material on to the body is of circular form in all cases, except that:
not permissible. a) for Class 150 valves they may be oval;
Separate seat rings may have directly deposited b) for all valves below nominal size 80 mm (3 in)
seating material in accordance with any of the they may be square or rectangular.
specifications indicated in Table 2, in which case the
Flanges shall be spot-faced or back-faced as
minimum thickness of the deposit shall be 1.6 mm.
specified in BS 1560-2.
Seat rings may be shoulder-seated or bottom-seated
9.5 The body to bonnet joint shall have at least four
at the option of the manufacturer and may be
stud-bolts of the following minimum size except that
screwed in, rolled in or welded in unless one
for nominal sizes below 50 mm (2 in) studs may be
particular method is specified by the purchaser.
used (see also 15.2).
Threaded seat rings shall be provided with lugs or
slots to facilitate removal. Shoulder-seated rings Nominal size Minimum nominal bolt size
shall be designed so that any clearance between mm in
the back of the ring and the bottom of the ring
recess shall be not greater than 1.6 mm for 25 to 50 b
sizes 300 mm (12 in) and smaller, and 3.2 mm for 80 to 200 ½
sizes 350 mm (14 in) and larger (see Figure 1). 250 and larger c
Tack welding may be employed to prevent loosening
(see BS 3351). The faces of the rings shall be smooth 9.6 To permit repacking of a valve in the open
finished with the sharp corners at the inner and position while in service, a machined conical or
outer edges removed to prevent scoring of the wedge spherical back seat shall be provided in the bonnet
faces. to contact a corresponding seating surface on the
valve stem. Bonnet back seats shall be in a bushing,
The use of a sealing medium on the threads is not except that for a valve with either an austenitic or
permissible. hard faced trim the seating surface may be a welded
The use of soft seals in body seats is dealt with in deposit. On an austenitic steel valve the back seat
clause 18. may be on either an integral surface or welded-on
8.11 Wedge guides shall be provided in the bodies of hardfacing. Welded deposits shall have a minimum
all valves to cover for the full travel of the wedge so finished thickness of 1.6 mm.
that the seating surfaces of the wedge do not touch 9.7 The hole at the back seat shall be designed to
the body seats until near the point of closure. These provide adequate guidance for the stem and to
guides shall be of the male or female type, so placed prevent packing extrusion.
as to engage with the guide slots or lugs of the 9.8 Valves of nominal size 80 mm (3 in) and larger
wedge. Valve guides shall be integral with the shall have provision for a ½ in tapping at the location
body except that for valves of nominal H shown in Figure 3. Provision for a ½ in tapping
sizes 650 mm (26 in) and larger the guides may shall also be made on valves smaller than nominal
be separate components welded into position. size 80 mm (3 in) at a position convenient to the
manufacturer. The thread shall be stated if other
9 Bonnet than API Std 5B.
9.1 For bonnets the design criteria specified in 9.2
to 9.8 shall be observed. 10 Wedge
9.2 Wall thickness of the bonnet shall conform with 10.1 For wedges the design criteria specified
shell thickness as shown in Appendix A. Drilling of, in 10.2 to 10.5 shall be observed.
or pinning to, the wall of a pressure containing part,
e.g. for nameplate fixing, is not permissible where it
would reduce the effective thickness below the
minimum permitted value.

© BSI 08-1999 7
BS 1414:1975

10.2 A solid wedge, which may be fabricated by 12.2 The valve shall be opened by turning the
welding, shall be provided. It may be either a plain handwheel in an anti-clockwise direction. The
wedge, having essentially a trapezoidal (or an I) handwheel shall be suitably marked with an arrow
cross section, or a flexible wedge having a tapered and the word OPEN to indicate the direction of
H or inverted U cross section. It shall be free from rotation to open the valve.
pockets which could form liquid traps when the 12.3 The handwheel shall be retained on the yoke
valve is mounted with the stem vertical. Unless the sleeve by a threaded handwheel nut.
order specifies a plain wedge or a flexible wedge,
either may be supplied. 13 Stem and yoke sleeve
10.3 Wedges may have integral faces or may have 13.1 The minimum stem diameter shall be as given
separate facing rings rolled in, welded on or directly in Appendix A.
deposited. Directly deposited facings shall have a
minimum finished thickness of 1.6 mm. 13.2 The stem shall be of one piece design and shall
have a bevelled or spherical seat machined on it to
The use of soft seals in wedge seats is dealt with in
seat on the bonnet back seat when the valve is fully
clause 18.
opened.
10.4 Guide slots or lugs to engage the body guides 13.3 The projection outside the yoke sleeve of the
shall be provided on the wedges of all valves. The stem threads on a new closed valve shall be as
slots or lugs shall be of ample length and shall
follows unless a closer tolerance is required by the
extend below the horizontal centre line of the wedge.
purchaser:
Wedges shall be provided with a suitable slot at the
top to receive the button or tee-head of the stem. Nominal size Limits of stem projection

10.5 The design shall provide adequate seating mm (in) mm

width, both before and afar wear of the seating 25 to 50 (1 to 2) 2 to 10
surfaces. The minimum values of wear travel shall
65 to 150 (2½ to 6) 3 to 15
be as follows:
200 to 300 (8 to 12) 6 to 20
Nominal size Minimum wear travel 350 to 450 (14 to 18) 10 to 30
mm mm 500 to 600 (20 to 24) 13 to 40
25 to 50 2 650 to 1 050 (26 to 42) 15 to 50
65 to 150 3 13.4 The stem shall have threads of Acme or other
200 to 300 6 trapezoidal form and shall have an integral end of
350 to 450 10 button or tee-head form, fitting into a slot in the top
500 to 600 13 of the wedge, to provide flexibility between the stem
650 to 1 050 15 and the wedge. The design shall prevent turning of
the stem or disengagement of the stem from the
11 Yoke wedge during service. Threaded or pinned
connections between the stem and the wedge shall
The yoke may be integral with the bonnet or, if not be used.
separate, self-locating on the bonnet and attached
13.5 The yoke sleeve shall be internally threaded to
by suitable bolting. The yoke shall be machined
suit the stem and shall be designed to permit ready
where it comes in contact with the bonnet and the
removal of the handwheel without allowing any
yoke sleeve. When specified in the order the yoke
axial movement of the stem.
shall be provided with an actuator or gearbox
mounting flange (see 16.4). The yoke and the 13.6 All surfaces of the yoke sleeve in contact with
actuator or gearbox mounting shall be of adequate the yoke shall be machined. Rolling bearings shall
strength to support the actuator or gearbox at any be fitted to the following nominal sizes of valve:
angle of installation of the valve. Class 400 250 mm (10 in) and
larger.
12 Handwheel and handwheel nut Class 600 and upwards 150 mm (6 in) and
12.1 The handwheel shall be of the spoke-and-rim larger.
design, preferably with not more than six spokes. In Adequate provision for lubrication shall be made in
the smaller sizes, where the space between the all classes and nominal sizes.
spokes is limited, the provision of knobs or studs
projecting beyond the outside diameter of the
handwheel is desirable.

8 © BSI 08-1999
 BS 1414:1975

14 Stuffing box, packing and lantern 15.3 Gland bolting may be of one of the following
ring types.
a) Hinged bolt secured by either a headed bolt
14.1 The stuffing box bore shall conform to the
dimensions given in Table 1 and shall have a passed through the eye and secured by a nut or a
minimum depth, based on square section packing of pin passed through the eye and effectively
secured. Cotter pins are not acceptable as the sole
the nominal width shown in the table, as follows.
securing devices.
Class 150 equivalent to six rings of
b) Stud-bolt passed through a plain hole in the
packing.
flange on the bonnet neck and secured to the
Class 300 and above equivalent to a lantern flange by two nuts.
ring length and seven rings
of packing. c) Stud-bolt screwed into a tapped hole in the
flange on the bonnet neck and secured by a lock
14.2 Packing glands shall be of one piece, one piece nut.
bushed, or two piece self-aligning design. Vertically d) Headed bolt passed through a plain hole in the
split glands shall not be used. The gland proper of a flange on the bonnet neck.
two piece gland shall have a shoulder on its outer
end to prevent complete entry of the gland into the Headed bolts in slotted brackets on the bonnet neck
stuffing box. shall not be used. Bolts, stud-bolts and nuts shall be
threaded metric or UNC and dimensioned in
14.3 The packing width shall be as specified in accordance with BS 4882, BS 1768 (below ½ in
Table 1. The packing may be of square, rectangular nominal size), BS 1769, BS 3692 or BS 4190 except
or chevron section. that square head, side head and tee head bolts are
14.4 Class 150 valves shall not have lantern rings. acceptable. Studs are not permissible.
Class 300 to Class 2 500 valves shall be supplied 15.4 Yoke bolting shall be threaded metric or UNC
with a lantern ring when specified in the order. and dimensioned in accordance with BS 4882,
Lantern rings shall have two holes, spaced at 180°, BS 1769, BS 3692 or BS 4190. Studs are not
provided at each end for removal. These holes shall permissible.
either be through-holes for hooks or
tapped 5-40 UNC. When a lantern ring is provided 16 Operation
it shall be positioned such that with square section
packing there will be five rings of packing above the 16.1 Valves shall be direct-handwheel operated
lantern ring and two below. The stuffing box shall unless otherwise specified in the order.
then be tapped opposite the centre of the installed 16.2 If chainwheel operation is required, the type of
lantern ring and fitted with a round head pipe chainwheel shall be specified in the order which
plug in accordance with BS 3799 of not less shall also specify any chain to be supplied.
than ¼ nominal size. A boss shall be provided if 16.3 If gear operation is required, the type of
necessary to ensure minimum thread engagement. gearing and its arrangement and the design
maximum differential pressure across the valve
15 Bolting shall be specified in the order.
15.1 This clause is concerned only with that bolting 16.4 If actuator operation is required, the details of
which forms part of the valve and is not concerned the actuator and its power supply together with the
with bolting for flanged connections between the design maximum pressure differential across the
valve and a pipeline or pipe fitting. valve shall be specified in the order.
15.2 The allowable working stress in bolting For multi-turn actuators the attachment
material for bonnet flanges at the primary service dimensions shall be as specified in BS . . . . “Flange
pressures given in clause 4 shall not exceed 62 MPa attachment dimensions of actuators to general
assuming that the pressure acts upon an area purpose valves” (in course of preparation).
circumscribed by the outside periphery of the gasket
or, for a ring joint, that the pressure acts through
the pitch circle of the ring joint.
Bonnet flange bolting shall be by stud-bolts with a
nut at each end of the stud-bolt except that for valve
sizes below 50 mm (2 in) studs in accordance with
BS 2693-1 may be used. Stud-bolts and nuts shall
comply with the requirements of BS 4882:1973,
sections 1 and 3.

© BSI 08-1999 9
BS 1414:1975

Table 1 — Stuffing box bore and packing widtha

1 2 3 4 5 6
Nominal stem diameter Nominal packing width Nominal bore of stuffing box
mm (in) mm (in) mm (in)

15.9 5--- 6.4 1--- 29.4 5

 1 ------
 8  4  32
 11
------ 1---
7
 1 ------
17.5  16 6.4  4 31.0  32
3--- 1 9
 1 ------
19.0  4 6.4 --- 32.5  32
 4

22.2 7--- 6.4 1---  1 13

------
 8  4 35.7  32
 1  1 17 
25.4 (1) 6.4  --4- 38.9  ------
32
11 5
 ------  1 25 
28.6 -
 -- 7.9  16 45.2  ------
8 32
11 5  1 29 
31.8 -
 -- 7.9  ------
 16 48.4  ------
32
4
13 5
 ------ 1
 2 ------
34.9 -
 --
8 7.9  16 51.6  32

38.1 11
--- 3  9
 2 ------
 2 9.5  --8- 57.9  32

41.3 15- 3   2 13 
 --
8 9.5  --8- 61.1  ------
32

44.4 13-  --3-  2 17 

 --
4 9.5  8 64.3  ------
32
47.6 17- 3   2 21 
 --
8 9.5  --8- 67.5  ------
32
50.8 (2) 11.1
7
 ------
73.8  2 29 
 16  ------
32
1
 2 --
54.0  8
-
11.1
7
 ------
 16 77.0  32
1
 3 ------

57.2 21- 1  9
 3 ------
 --
4 12.7  --2- 83.3  32

60.3 23- 1   3 13 
 --
8 12.7  --2- 86.5  ------
32
21
---
63.5  2 12.7 1  89.7  3 17
 ------

 --2- 32
3
 2 --
69.8  4- 12.7  --1- 96.0  3 25 
 2  ------
32
73.0 27
--- 9 1
 4 ------
 ------ 102.4
 8 14.3  16  32
76.2 (3) 9
 ------
5
 4 ------
14.3  16 105.6  32
82.6 31
---
 4 3   4 25 
19.0  --4- 121.4  ------
32
88.9 1
 3 --
 2- 19.0 3  127.8
1
 5 ------
 --4-  32
95.2 33- 9
 5 ------
 --
4 19.0 3  134.1
 --4-  32
101.6 (4) 3   5 17 
19.0  --4- 140.5  ------
32
108.0 41-  5 25
 --
4 19.0 3 
146.8  ------

 --4- 32
127.0 (5) 25.4 (1) 178.6 1
 7 ------
 32
a For intermediate sizes of stem one of the standard packing widths listed shall be used.

10 © BSI 08-1999
 BS 1414:1975

17 Bypass 20 Body seat rings

17.1 A bypass shall not be provided unless specified A body seat ring made of a material different from
in the order. its seating surface shall be of a material not inferior
17.2 Any bypass supplied shall be external to the to that of the shell.
main valve and be of the following size:
21 Bonnet gasket
Nominal size Bypass size
Bonnet flange gaskets shall be metallic spiral
mm in
wound as specified in BS 3381, or steel or soft iron,
50 to 100 ½ except that, for Class 150 valves only, compressed
150 to 200 ¾ asbestos fibre complying with the requirements of
250 to 300 1 BS 1832 is an acceptable alternative. They shall be
350 and larger 1½ suitable for the pressure/temperature rating of the
valve. Any metallic part of the gasket shall have at
least the same corrosion resistance as the shell.
18 Soft seal rings
NOTE Free chlorides in compressed asbestos fibre materials
18.1 Soft seal rings may be fitted in either the body when used with low alloy or austenitic stainless steels may cause
seats or in the wedge seats as specified by the stress corrosion cracking in the flange and the use of alternative
gasket materials should be considered.
purchaser. The rings shall be designed to compress
down to the level of the metal seats to give a tight 22 Wedge
shut-off on both sides of the wedge and thus provide
a “double block and bleed” facility. They shall also A wedge fitted with separate facing rings, or on
give a tight metal-to-metal seal through the valve if which seating surfaces are deposited by welding,
the soft seals are damaged or removed. shall be of a material equal to that of the shell.
18.2 The seal rings shall be designed to withstand a
minimum of 2 000 cycles of operation in dry 23 Yoke
atmospheric conditions and there shall then be no A yoke separate from the bonnet shall be of carbon
evidence of damage or cold flow, as revealed by steel or of the same material as that of the shell.
spreading over the metal seats. The valves shall
then meet the hydrostatic and air tests specified in 24 Handwheel or chainwheel
BS 5146.
The handwheel or chainwheel shall be of steel,
A ½ in tapping fitted with a plug shall be provided in malleable iron or nodular iron.
the bonnet for testing the double block and bleed
facility. This shall be located in position H 25 Handwheel or chainwheel nut
(see Figure 3) unless specified otherwise by the
purchaser. The type of thread shall be stated if other The handwheel or chainwheel nut shall be of copper
than API Std 5B. alloy, steel, malleable iron or nodular iron. If of
carbon steel it shall be suitably protected against
18.3 The effective operating temperature range of corrosion.
soft seal valves will be limited by the service
temperature of the seal material. 26 Yoke sleeve
Section 3. Materials The yoke sleeve shall be of non-rusting metal having
a suitable bearing quality and a melting point
19 Shell above 955 °C.
The body and bonnet shall be of the material 27 Yoke sleeve retaining nut
specified in the order, the selection being made from
those listed in BS 1560-2. All pressure containing The yoke sleeve retaining nut shall be of a material
parts involved in welding operations shall have the having a melting point above 955 °C. Grey cast iron
carbon content restricted as follows: shall not be used. If malleable cast iron is used it
shall comply with the requirements of BS 6681 for
a) 0.25 % maximum for carbon or
grade B 32-10 or grade B 35-12. If spheroidal
carbon/molybdenum steels;
graphite cast iron is used it shall comply with the
b) 0.15 % maximum for 5 % Cr ½ % Mo steel. requirements of BS 2789
grades 350/22, 400/18 or 420/12.

© BSI 08-1999 11
BS 1414:1975

28 Gland 33 Plugs
A one piece gland or any gland flange shall be of Material for shell plugs shall be not inferior to that
steel. The bushing of a one piece bushed gland or the of the shell.
gland proper of a two piece gland shall be made of a
material having a minimum melting point 34 Nameplate
above 955 °C. 34.1 For valves of nominal size 150 mm (6 in) and
larger the nameplate shall be of 18-8 Cr-Ni steel or
29 Trim nickel alloy attached to the valve by pins of similar
29.1 Trim comprises the following: material or by welding.
a) stem; 34.2 For smaller valves, the nameplate material
b) body seat surfaces; and attachment shall be of corrosion resistant
material in accordance with the manufacturer’s
c) wedge seat surfaces;
standard. Brass and aluminium are acceptable.
d) back seat bushing.
29.2 The trim materials shall be selected from those 35 Soft seals
listed in Table 2 and specified in the order by Soft seals shall be of the manufacturer’s standard
quoting the relevant nominal trim symbol. material for the duties specified. Any retaining ring
29.3 If a combination trim, e.g. CR 13 and Cu-Ni, is in the wedge shall be of the same material as the
specified, either material may be used for the body stem but any fixing screws shall be of 18-8 Cr-Ni
seat surface. The other material of the combination steel.
shall be used for the wedge seat surface.
29.4 Stems shall be of wrought material. 36 Special applications
29.5 The temperature limitations of certain trim When valves are specified for highly corrosive
materials may restrict the pressure/temperature services or environment, or for low temperature
ratings of the valve to which they are fitted. service, the material specification for all parts shall
be subject to agreement between the purchaser and
30 Lantern ring the manufacturer.
A lantern ring, when supplied, shall be of a material
not inferior to that of the shell. Section 4. Marking

31 Stem packing 37 Required markings

The packing shall be of braided asbestos containing Every valve in accordance with this standard shall
a suitable corrosion inhibitor. Unless the order be clearly marked as follows.
specifies other packing or a higher packing design a) Body and bonnet markings shall be integral.
temperature, it shall be suitable for use with steam b) Every valve shall have a nameplate securely
or petroleum fluid at a minimum packing design fastened to it.
temperature of 400 °C.
38 Body and nameplate markings
32 Bolting
Body and nameplate markings shall be as follows.
32.1 Bonnet bolts shall comply with the a) Nominal size designation. The numeral(s)
requirements of BS 1506-630-860 (BS 4882:1973, denoting the nominal size prefixed by the
section 3, grade B7) and nuts shall comply with the letters DN, e.g. DN 100 (see clause 6).
requirements of BS 1506-162 (BS 4882:1973,
section 3, grade 2H) unless other bolting material is b) Class rating. The numerals denoting the class
specified in the order. rating (see clause 4).
32.2 Material for gland and yoke bolting shall be c) Body material identification. Standard symbol
carbon steel of at least 392 N/mm2 1) tensile from BS 1560-2:1970, Table 25.
strength unless other bolting material is specified in d) Manufacturer’s name or trade mark.
the order. Free cutting steels shall not be used. e) The number of this British Standard,
i.e. BS 1414.

1)
1 N/mm2 = 1 MPa.

12 © BSI 08-1999
 Table 2 — Trim materials, hardness and acceptable specifications
© BSI 08-1999

1 2 3 4 5 6 7 8 9 10 11 12 13
Nominal Material type Minimum Brinell hardnessa Acceptable material specifications
trim
Seat Stem Back seat Seat Stem Back seat Castb Forged Bar
symbol
surfaces bushingc surfaces bushing BS ASTM BS ASTM BS ASTM
CR 13 13 Cr 13 Cr 13 Cr d 200 250 1504-420C29 A487-CA15 1503-410S21 A182-F6 1506-410S21 A276-410
A487-CA6NM
18-8 Ti 18-8 18-8 18-8 Manufacturer’s standard 1504-347C17 — 1503-321S31 A182-F321 1506-321S31 A276-321
Cr-Ni-Ti Cr-Ni-Ti Cr-Ni-Ti 1503-321S51
18-8 Nb 18-8 18-8 18-8 Manufacturer’s standard 1504-347C17 A351-CF8C 1503-347S31 A182-F347 1506-347S31 A276-347
Cr-Ni-Nb Cr-Ni-Nb Cr-Ni-Nb 1503-347S51
18-10-2 18-10-2 18-10-2 18-10-2 Manufacturer’s standard 1504-316C16 A351-CF8M 1503-316S31 A182-F316 1506-316S31 A276-316
Cr-Ni-Mo Cr-Ni-Mo Cr-Ni-Mo 1503-316S33 1506-316S33
18-12-3 18-12-3 18-12-3 18-12-3 Manufacturer’s standard 1504-317C16 — 1503-316S33 — — A276-317
Cr-Ni-Mo Cr-Ni-Mo Cr-Ni-Mo
25-20 25-20 25-20 25-20 Manufacturer’s standard — — — A182-F310 — —
Cr-Ni Cr-Ni Cr-Ni
HF 66-26-5 — — 350e — — — — — — — —
Co-Cr-W
— 13 Cr 13 Cr — 200 250 1504-420C29 A487-CA15 1503-410S21 A182-F6 1506-410S21 A276-410
CR 13 13 Cr 13 Cr 13 Cr 250f 200 250 1504-420C29 A487-CA15 1503-410S21 A182-F6 1506-410S21 A276-410
and Cu-Ni — — 175 f — — Manufacturer’s standard with 30 % nickel min.
Cu-Ni
CR 13 13 Cr 13 Cr 13 Cr 300f 200 250 1504-420C29 A487-CA15 1503-410S21 A182-F6 1506-410S21 A276-410
and 66-26-5 — — f — — — — — — — —
350
HF
Co-Cr-W
Ni-Cu Ni-Cu Ni-Cu Ni-Cu — — — 3071 NA1 — — — 3076 NA13 —
Alloy Alloy Alloy
AB Aluminium Aluminium Aluminium Manufacturer’s standard 1400-AB1, B148-952A, 2872-CA104 B124-642 2874-CA107 B150-642
bronze bronze bronze 1400-AB2 B148-955D B124-630 2874-CA104 B150-630
B Bronze — Bronze Manufacturer’s standard 1400-G1, B584-905 — — — —
1400-LG2 B584-836
— Manganese Manganese Manufacturer’s standard 1400-HTB1 B584-864 2872-CZ114 B138-675 2874-CZ114 B138-675
bronze bronze B584-865

BS 1414:1975
a
See BS 240-1.
b
Castings not applicable to stem materials; see 29.4.
c
For austenitic trims the backseat may alternatively be a weld deposit of the same nominal material composition as the trim or a welded-on hard facing. For hard faced (HF)
trim the back seat may alternatively be a welded-on hard facing.
d
Body and wedge seat surfaces 250 HB min., with 50 HB min. differential between body and wedge seat surfaces.
e
Differential hardness between body and wedge seat surfaces is not required.
f
Differential hardness between body and wedge seat surfaces shall be the Manufacturer’s standard.
13
BS 1414:1975

39 Body and bonnet markings 42 Omission of markings

39.1 Melt identification. Melt identification is 42.1 Where the size or shape of the valve body
required on all pressure containing steel castings. precludes the inclusion of all the required markings,
39.2 Ring joint number. Pipe end flanges and they may be omitted from the body only as found
body/bonnet flanges grooved for ring joints and the necessary subject to the approval of the purchaser.
rings to be used with them shall be marked with the The sequence of omission shall be as follows.
corresponding ring number (e.g. R 25). This 1) Nominal size
identification shall be placed on the rim of both pipe 2) Manufacturer’s name or trade mark
end flanges or the bonnet end flange of the body as
3) Class rating.
applicable and on the outside periphery of the ring.
For ring numbers see Appendix A. In the case of 42.2 The number of this British Standard may be
non-standard ring joints for body/bonnet flanges the omitted from the body or the nameplate, but not
flange and ring shall be marked R SpL. from both, at the manufacturer’s option.

40 Nameplate markings Section 5. Testing

40.1 Pressure/temperature restrictions. Any 43 Production pressure testing
pressure or temperature restrictions within the
appropriate ratings given in BS 1560-2 that may be All valves shall be pressure tested by the
imposed by the manufacturer due to limitations on manufacturer before despatch in accordance with
materials or design shall be shown on the BS 6755-1 as follows:
nameplate. a) hydrostatic shell and backseat tests;
Such special limiting pressure/temperature ratings b) hydrostatic seat test (see note);
shall also comply with the appropriate BS 1560-2 c) pneumatic seat test (see note).
rating table.
The test durations shall be as given in Table 2a.
40.2 Valve trim identification. Trim materials
NOTE Attention is drawn to note of D.8.3.2 of BS 6755-1:1986
shall be indicated in the following order, using the regarding the sequence of operations when the seat test
appropriate symbol from Table 2, procedure is carried out. Valves tested to BS 1414 should have
the sequence of items b) and c) in D.8.3.2 of BS 6755-1:1986
1) STEM 2) WEDGE 3) SEAT reversed. Seat test leakage rate A should apply. For the backseat
test there should be no visual leakage for the duration of the test
as in the example below: time.
STEM CR 13 CR 13 Table 2a — Test durations
WEDGE HF or CR 13 HF CR 13 or HF Nominal valve size Minimum test duration

SEAT CR 13 CR 13 Shell test Backseat Seat test

test
40.3 Identification number. The manufacturer’s s s s
figure or number identifying the valve in all
Up to and
respects shall be shown. The same figure or number
including DN 50 15 15 15
shall therefore only be used for valves which are
identical in design, detail, dimensions and material DN 65 up to and
and which have interchangeable parts. including DN 150 60 15 60
DN 200 up to and
41 Additional markings including DN 300 120 15 120
Additional markings may be used at the option of DN 350 and larger 300 15 120
the manufacturer provided they do not conflict with
any of the markings specified in this standard.

14 © BSI 08-1999
 BS 1414:1975

Section 6. Shipping 45.2 End protection. After complying with the

requirements of 45.1, body end ports, flange faces
44 Preliminary and butt-welding ends shall be covered with
suitable close fitting protectors to protect the
After inspection and before preparation for despatch
machined ends and prevent ingress of dirt and
all valves shall be thoroughly cleaned and dried. moisture.
45 Preparation for despatch 45.3 Stem packing. The stem packing shall be
fitted before shipping.
45.1 Coating. Coating of valves shall be as follows.
45.4 Wedge. The wedge shall be closed before
a) Unmachined external surfaces of the valves shipping except in the case of soft seal valves where
shall be painted with aluminium finish paint, the wedge shall be backed off to relieve the pressure
except for austenitic steel valves which shall not on the seals.
be painted.
b) Machined or threaded surfaces shall be coated 46 Packaging
with an easily removable rust protective
Valves shall be so packaged as to minimize the
(see BS 1133-6) except that this shall not be possibility of damage during storage or transit.
required for austenitic steel components. Where tropical or special packaging is necessary,
the purchaser shall specify his requirements.

© BSI 08-1999 15
BS 1414:1975

Appendix A Particular dimensions for each class of valve

Table 3 — Dimensions of Class 150 valves
1 2 3 4 5 6

Nominal size Inside diameter of Body and bonnet Ring number for ring Stem diameter
flanged valves (min)a thickness (min) joints (min.)

mm (in) mm mm mm

25 (1) 25 6.4 R15 15.9

32b (1¼)b 32 6.4 R17 15.9
40 (1½) 38 6.4 R19 17.5
50 (2) 51 8.7 R22 19.0
65b (2½)b 64 9.5 R25 19.0
80 (3) 76 10.3 R29 22.2
100 (4) 102 11.1 R36 25.4
150 (6) 152 11.9 R43 28.6
200 (8) 203 12.7 R48 31.8
250 (10) 254 14.3 R52 34.9
300 (12) 305 15.9 R56 38.1
350 (14) 337 16.7 R59 41.3
400 (16) 387 17.5 R64 44.4
450 (18) 438 18.2 R68 47.6
500 (20) 489 19.0 R72 50.8
600 (24) 591 20.6 R76 57.2
650 (26) 635 21.4 — 60.3
700 (28) 686 22.2 — 63.5
750 (30) 737 23.0 — 63.5
900 (36) 876 25.4 — 69.8
1 050 (42) 1 020 28.6 — 82.6
a For details of welding ends including inside diameters see Figure 2.
b These sizes have been retained for the purpose of replacing existing valves. Their use for new construction in piping
systems using BS 1560-2 flanges should be avoided.

16 © BSI 08-1999
 BS 1414:1975

Table 4 — Dimensions of Class 300 valves

1 2 3 4 5 6

Nominal size Inside diameter of Body and bonnet Ring number for ring Stem diameter (min.)
flanged valves (min.)a thickness (min.) joints

mm (in) mm mm mm

25 (1) 25 6.4 R16 15.9

32b (1¼)b 32 6.4 R18 15.9
40 (1½) 38 7.9 R20 19.0
50 (2) 51 9.5 R23 19.0
65b (2½)b 64 11.1 R26 19.0
80 (3) 76 11.9 R31c 22.2
100 (4) 102 12.7 R37 25.4
150 (6) 152 15.9 R45 31.8
200 (8) 203 17.5 R49 34.9
250 (10) 254 19.0 R53 38.1
300 (12) 305 20.6 R57 41.3
350 (14) 337 22.2 R61 44.4
400 (16) 387 23.8 R65 47.6
450 (18) 432 25.4 R69 50.8
500 (20) 483 27.0 R73 54.0
600 (24) 584 30.2 R77 63.5
650 (26) 635 31.8 — 69.8
700 (28) 686 33.3 — 76.2
750 (30) 737 34.9 — 82.6
900 (36) 876 41.3 — 88.9
1 050 (42) 1 020 44.4 — 101.6
a For details of welding ends including inside diameters see Figure 2.
b These sizes have been retained for the purpose of replacing existing valves. Their use for new construction in piping systems
using BS 1560-2 flanges should be avoided.
c For valves of 80 mm (3 in) nominal size, if intended to be used in conjunction with lapped flanges, the ring
number shall be R30.

Table 5 — Dimensions of Class 400 valves

1 2 3 4 5 6

Nominal size Inside diameter of Body and bonnet Ring number for ring Stem diameter (min.)
flanged valves (min.)a thickness (min.) joints

mm (in) mm mm mm

100 (4) 102 12.7 R37 28.6

150 (6) 152 16.7 R45 34.9
200 (8) 203 19.0 R49 38.1
250 (10) 254 21.4 R53 44.4
300 (12) 305 23.8 R57 47.6
350 (14) 333 27.0 R61 47.6
400 (16) 381 28.6 R65 50.8
450 (18) 432 30.2 R69 57.2
500 (20) 479 33.3 R73 63.5
600 (24) 575 36.5 R77 69.8
a
For details of welding ends including inside diameters see Figure 2.

© BSI 08-1999 17
BS 1414:1975

Table 6 — Dimensions of Class 600 valves

1 2 3 4 5 6

Nominal size Inside diameter of Body and bonnet Ring number for ring Stem diameter (min.)
flanged valves (min.)a thickness (min.) joints

mm (in) mm mm mm

25 (1) 25 7.9 R16 15.9

32b (1¼)b 32 8.6 R18 15.9
40 (1½) 38 9.3 R20 19.0
50 (2) 51 11.1 R23 19.0
65b (2½)b 64 11.9 R26 22.2
80 (3) 76 12.7 R31c 25.4
100 (4) 102 15.9 R37 28.6
150 (6) 152 19.0 R45 38.1
200 (8) 200 25.4 R49 41.3
250 (10) 248 28.6 R53 47.6
300 (12) 298 31.8 R57 50.8
350 (14) 327 34.9 R61 57.2
400 (16) 375 38.1 R65 60.3
450 (18) 419 41.3 R69 63.5
500 (20) 464 44.4 R73 69.8
600 (24) 559 50.8 R77 76.2
a For details of welding ends including inside diameters see Figure 2.
b These sizes have been retained only for the purpose of replacing existing valves. Their use for new construction in piping
systems using BS 1560-2 flanges should be avoided.
c For valves of 80 mm (3 in) nominal size, if intended to be used in conjunction with lapped flanges, the ring
number shall be R30.

Table 7 — Dimensions of Class 900 valves

1 2 3 4 5 6

Nominal size Inside diameter of Body and bonnet Ring number for ring Stem diameter (min.)
flanged valves (min.)a thickness (min.) joints

mm (in) mm mm mm

80 (3) 73 19.0 R31 28.6

100 (4) 98 21.4 R37 31.8
150 (6) 146 26.2 R45 41.3
200 (8) 190 31.8 R49 47.6
250 (10) 238 36.5 R53 54.0
300 (12) 283 42.1 R57 57.2
350 (14) 311 46.0 R62 60.3
400 (16) 356 52.4 R66 63.5
450 (18) 400 57.2 R70 76.2
500 (20) 444 63.5 R74 82.6
600 (24) 533 73.0 R78 101.6
a
For details of welding ends including inside diameters see Figure 2.

18 © BSI 08-1999
 BS 1414:1975

Table 8 — Dimensions of Class 1 500 valves

1 2 3 4 5 6

Nominal size Inside diameter of Body and bonnet Ring number for ring Stem diameter (min.)
flanged valves (min.)a thickness (min.) joints

mm (in) mm mm mm

25 (1) 22 12.7 R16 19.0

32b (1¼)b 29 14.2 R18 19.0
40 (1½) 35 15.0 R20 22.2
50 (2) 48 19.0 R24 25.4
65b (2½)b 57 22.2 R27 28.6
80 (3) 70 23.8 R35 31.8
100 (4) 92 28.6 R39 34.9
150 (6) 137 38.1 R46 44.4
200 (8) 178 47.6 R50 54.0
250 (10) 222 57.2 R54 63.5
300 (12) 264 66.7 R58 69.8
350 (14) 289 69.8 R63 76.2
400 (16) 330 79.4 R67 82.6
450 (18) 371 88.9 R71 95.2
500 (20) 416 98.4 R75 108.0
600 (24) 498 114.3 R79 127.0
a For details of welding ends including inside diameters see Figure 2.
b These sizes have been retained only for the purpose of replacing existing valves. Their use for new construction in piping
systems using BS 1560-2 flanges should be avoided.

Table 9 — Dimensions of Class 2 500 valves

1 2 3 4 5 6

Nominal size Inside diameter of Body and bonnet Ring number for ring Stem diameter (min.)
flanged valves (min.)a thickness (min.) joints

mm (in) mm mm mm

25 (1) 19 15.1 R18 19.0

32b (1¼)b 25 17.5 R21 19.0
40 (1½) 29 19.0 R23 22.2
50 (2) 38 22.2 R26 25.4
65b (2½)b 48 25.4 R28 28.6
80 (3) 57 30.2 R32 31.8
100 (4) 73 35.7 R38 34.9
150 (6) 111 48.4 R47 47.6
200 (8) 146 61.9 R51 60.3
250 (10) 184 67.5 R55 73.0
300 (12) 219 86.5 R60 82.6
a
Fordetails of welding ends including inside diameters see Figure 2.
b
These sizes have been retained only for the purpose of replacing existing valves. Their use for new construction in piping
systems using BS 1560-2 flanges should be avoided.

© BSI 08-1999 19
BS 1414:1975

Appendix B Application to piping B.4 Body end flanges

systems with BS 4504 flanges B.4.1 Dimensions. Body end flange dimensions shall
comply with the requirements of BS 4504 except
B.1 General
that flange thicknesses may be the appropriate
Valves in accordance with this British Standard, values from BS 1560-2. Flange thicknesses shall be
BS 1414, may be supplied for use in piping systems not less than those specified in BS 4504. When
with BS 4504 flanges when specified by the flange thicknesses comply with those specified in
purchaser. When this is the case all the BS 4504, the neck dimensions shall also comply
requirements of this British Standard, BS 1414, with the requirements of BS 4504.
apply, with the qualifications specified in B.2 to B.7.
B.4.2 Spot-facing or back-facing. The requirements
B.2 Pressure/temperature ratings of BS 1560-2 for spot-facing or back-facing shall be
The pressure/temperature ratings of valves with complied with.
BS 4504 flanges shall be in accordance with B.4.3 Finish of joint surface. The joint surface finish
BS 4504:1969, Table A.1. Pressure/temperature shall comply with the requirements of BS 4504.
ratings for valves in materials other than those
B.5 Text deleted.
listed in BS 4504:1969, Table A.1 shall be agreed
between the purchaser and the manufacturer. B.6 Marking
B.3 Nominal pressure and class ratings and When supplied for use in piping systems with
nominal size range BS 4504 flanges valves shall be permanently
marked with the appropriate nominal pressure
Valves in accordance with this appendix with
rating (i.e. PN. .). This marking may replace or
flanges of the nominal pressure ratings given
supplement the requirements of
in column 1 of Table 10 shall have the same
face-to-face dimensions as valves with BS 1560-2 clause 38 b) and shall appear on all BS 4504 flanges
flanges of the corresponding class ratings in used.
column 2. Column 3 gives the applicable nominal B.7 Information to be supplied by the
size range. purchaser
Table 10 — Nominal pressure and class ratings The information to be supplied by the purchaser
and nominal size range shall be as listed in clause 7 of this standard except
that a) shall be replaced by the following.
1 2 3 4
a) State that valves are to comply with the
Rating Nominal size range requirements of this appendix and state nominal
PN Class pressure rating and nominal size.
mm (in)

10 150 50 to 600 (2 to 24)

16 150 50 to 600 (2 to 24)
25 300 25 to 600 (1 to 24)
40 300 25 to 600 (1 to 24)
64 600 25 to 600 (1 to 24)
100 600 25 to 600 (1 to 24)
160 900 25 to 300 (1 to 12)
250 1 500 25 to 300 (1 to 12)
320 2 500 25 to 250 (1 to 10)
400 2 500 25 to 200 (1 to 8)

20 © BSI 08-1999
 BS 1414:1975

Publications referred to

This standard makes reference to the following British Standards:

BS 240, Method for Brinell hardness test.
BS 240-1, Testing of metals.
BS 1133, Packaging code.
BS 1133-6, Temporary protection of metal surfaces against corrosion (during transport and storage).
BS 1400, Specification for copper alloy ingots and copper alloy and high conductivity copper castings.
BS 1503, Specification for steel forgings (including semi-finished forged products) for pressure purposes.
BS 1504, Specification for steel castings for pressure purposes.
BS 1506, Specification for carbon, low alloy and stainless steel bars and billets for bolting material to be
used in pressure retaining applications.
BS 1560, Steel pipe flanges and flanged fittings (nominal sizes ½ in to 24 in) for the petroleum industry.
BS 1560-2, Metric dimensions.
BS 1600, Dimensions of steel pipe for the petroleum industry.
BS 1600-2, Metric units.
BS 1768, Unified precision hexagon bolts, screws and nuts (UNC and UNF threads). Normal series.
BS 1769, Unified black hexagon bolts, screws and nuts (UNC and UNF threads). Heavy series.
BS 1832, Oil resistant compressed asbestos fibre jointing.
BS 2080, Face-to-face, centre-to-face, end-to-end and centre-to-end dimensions of flanged and butt-welding
end steel valves for the petroleum, petrochemical and allied industries.
BS 2693, Screwed studs.
BS 2693-1, General purpose studs.
BS 2789, Specification for spheroidal graphite or nodular graphite cast iron.
BS 2872, Copper and copper alloys. Forging stock and forgings.
BS 2874, Copper and copper alloys. Rods and sections (other than forging stock).
BS 3071, Nickel-copper alloy castings.
BS 3076, Nickel and nickel alloys. Rods.
BS 3293, Carbon steel pipe flanges (over 24 in nominal size) for the petroleum industry.
BS 3351, Piping systems for petroleum refineries and petrochemical plants.
BS 3381, Metallic spiral wound gaskets for the petroleum and petrochemical industry.
BS 3600, Dimensions and masses per unit length of welded and seamless steel pipes and tubes for pressure
purposes.
BS 3692, ISO metric precision hexagon bolts, screws and nuts.
BS 3799, Forged steel pipe fittings, screwed and socket-welding for the petroleum industry.
BS 4190, ISO metric black hexagon bolts, screws and nuts.
BS 4504, Flanges and bolting for pipes, valves and fittings. Metric series.
BS 4882, Bolting for flanges and pressure containing purposes.
BS 6681, Specification for malleable cast iron.
BS 6755, Testing of valves.
BS 6755-1, Specification for production pressure testing requirements.
BS . . . ., Flange attachment dimensions of actuators to general purpose valves2).

2)
In course of preparation.

© BSI 08-1999
BS 1414:
1975
BSI — British Standards Institution
BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.

Revisions

British Standards are updated by amendment or revision. Users of

British Standards should make sure that they possess the latest amendments or
editions.

It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: 020 8996 9000. Fax: 020 8996 7400.

BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.

Buying standards

Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.

In response to orders for international standards, it is BSI policy to supply the

BSI implementation of those that have been published as British Standards,
unless otherwise requested.

Information on standards

BSI provides a wide range of information on national, European and

international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: 020 8996 7111. Fax: 020 8996 7048.

Subscribing members of BSI are kept up to date with standards developments

and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: 020 8996 7002. Fax: 020 8996 7001.

Copyright

Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.

This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
written permission of BSI must be obtained.

If permission is granted, the terms may include royalty payments or a licensing

agreement. Details and advice can be obtained from the Copyright Manager.
BSI Tel: 020 8996 7070.
389 Chiswick High Road
London
W4 4AL