ABS AF312A

Injection Molding

Description Application
Flame Retardant Electric/Electronic Applications(TV, Monitor Housing)
IT/OA device

Properties Test Condition Test Method Unit Typical Value

Physical
Specific Gravity ASTM D792 - 1.19
Molding Shrinkage (Flow), 3.2mm ASTM D955 % 0.4~0.7
Melt Flow Rate 220℃/10kg ASTM D1238 g/10min 55

Mechanical
Tensile Strength, 3.2mm ASTM D638
@ Yield 50mm/min kg/cm2 440
Tensile Elongation, 3.2mm ASTM D638
@ Yield 50mm/min % 5
@ Break 50mm/min % 20
Tensile Modulus, 3.2mm 1mm/min ASTM D638 kg/cm2 23,000
Flexural Strength, 6.4mm 15mm/min ASTM D790 kg/cm2 720
Flexural Modulus, 6.4mm 15mm/min ASTM D790 kg/cm2 27,000
IZOD Impact Strength, 6.4mm ASTM D256
(Notched) 23℃ kg·cm/cm 23
-30℃ kg·cm/cm 8
IZOD Impact Strength, 3.2mm ASTM D256
(Notched) 23℃ kg·cm/cm 24
-30℃ kg·cm/cm 8
Rockwell Hardness R-Scale ASTM D785 - 104

Thermal
Heat Deflection Temperature, 6.4mm ASTM D648
(Unannealed) 18.6kg ℃ 76
4.6kg ℃ 84
Vicat Softening Temperature ASTM D1525
5kg, 50℃/h ℃ 83
Flammability UL94
1.5mm class V-0
2.0mm class V-0,5VB
2.5mm class V-0,5VB
3.0mm class V-0,5VB
Relative Temperature Index UL 746B
Electrical ℃ 85
Mechanical with Impact ℃ 75
Mechanical without Impact ℃ 75
Note) Typical values are only for material selection purpose, and variation within normal tolerances are for various colors.
Values given should not be interpreted as specification and not be used for part or tool design.
All properties, except melt flow rate are measured on injection molulded specimens and after 48 hours storage at 23℃, 50% relative humidty.

Updated : 9-Nov-09
The information contained herein, including, but not limited to, data, statements and typical values, are given in good faith. LG Chem makes no warranty or guarantee,
expressed or implied, (i) that the result described herein will be obtained under end - use conditions, or (ii) as to the effectiveness or safety of any design incorporating LG
Chem materials, products, recommendations or advice. Further, any information contained herein shall not be construed as a part of legally binding offer. Especially, the
typical values should be regarded as reference values only and not as binding minimum values. Each user bear full responsibility for making its own determination as to the
suitability of LG Chem's materials, products, recommendations, or advice for its own particular use. Each user must identify and perform all tests and analyses necessary to
assure that its finished parts incorporating LG Chem material or products will be safe and suitable for use under end - use conditions. The data contained herein can be
changed without notice as a result of the quality improvement of the products.
 ABS AF312A
Injection Molding

Description Application
Flame Retardant Electric/Electronic Applications(TV, Monitor Housing)
IT/OA device

Processing Guide (Injection Molding)

Processing Parameters Unit Value

Drying Temperature ℃ 70 ~ 80
Drying Time hrs 2~4
Minimum Moisture Content % 0.01
Melt Temperature ℃ 200 ~ 230
Rear ℃ 170 ~ 190
Cylinder Temperature Middle ℃ 180 ~ 200
Front ℃ 190 ~ 210
Nozzle Temperature ℃ 200 ~ 230
Mold Temperature ℃ 40 ~ 60
Back Pressure kg/cm2 5 ~ 10
Screw Speed rpm 30 ~ 60
Note) Back Pressure & Screw Speed are only mentioned as general guidelines.
These may not apply or need adjustment in specific situations such as low shot sizes, thin wall molding and gas-assist molding.

Updated : 9-Nov-09
The information contained herein, including, but not limited to, data, statements and typical values, are given in good faith. LG Chem makes no warranty or guarantee,
expressed or implied, (i) that the result described herein will be obtained under end - use conditions, or (ii) as to the effectiveness or safety of any design incorporating LG
Chem materials, products, recommendations or advice. Further, any information contained herein shall not be construed as a part of legally binding offer. Especially, the
typical values should be regarded as reference values only and not as binding minimum values. Each user bear full responsibility for making its own determination as to the
suitability of LG Chem's materials, products, recommendations, or advice for its own particular use. Each user must identify and perform all tests and analyses necessary to
assure that its finished parts incorporating LG Chem material or products will be safe and suitable for use under end - use conditions. The data contained herein can be
changed without notice as a result of the quality improvement of the products.