DYNAHOIST VECTOR II

DYNAC VECTOR II
Using display and keyboard.
Password levels

© 2011 Konecranes Plc. All rights reserved. 1

©2015 Konecranes Plc. All right reserved
 Display

• Comprehensive menu with multilevel

structure;
• Drive operating parameters monitoring;
• Possibility to change Drive operating
parameters;
• Parameters upload and download from the
display to the drive and back;
• Fault History log and fault code view
possibility.

2
©2015 Konecranes Plc. All right reserved 2
 Display

Drive status indications:

– Motor is running
– Motor rotation direction
– Inverter is not running
– AC power is on
– Warning is on
– Fault is on

Control place indications :

I/O term Terminals are the selected control place
Keypad Control keypad is the selected control
place
Bus/Comm Control through Profibus is selected

3
©2015 Konecranes Plc. All right reserved 3
 Display

Text lines:

Line 1 Location indication (parameter number)

Line 2 Description line (parameter name)
Line 3 Value line (parameter value)

Status LEDs :
ready green Illuminates the AC-supply is on
run green Illuminates during run
fault red Illuminates due to fault trip

4
©2015 Konecranes Plc. All right reserved 4
 Control keypad operation

Button descriptions :

5
©2015 Konecranes Plc. All right reserved 5
 Control keypad operation

Special button functions

6
©2015 Konecranes Plc. All right reserved 6
 Using keyboard

M8.
STOP READY
I/O term
H8.1.
STOP READY
I/O term
T8.1.1.
STOP READY
I/O term • Intuitive keyboard for changing and
Fault History 57 Thermistor Operation days
H1Hxx  F T1T13  0 monitoring of the parameters;
STOP READY

M7. I/O term

Active Faults
F0
• Better to try using keyboard than to hear
STOP READY STOP READY STOP READY
how to use it.
M6. I/O term
S6.7. I/O term
I 6.7.2. I/O term

System Menu Info Unit voltage

S1S9  I1I7  500 V
STOP READY STOP READY

G5. I/O term

B5.1. I/O term

Panel Control Panel Control

B1R2  Off
STOP READY STOP READY

G4. I/O term

V4.19. I/O term

Monitoring Output Frequency

G1G20  0.00 Hz
STOP READY STOP READY STOP READY

G3. I/O term

G3.4. I/O term
G3.4.1. I/O term

Parameters Motor Parameters Motor Set 1

G1G7  G1G6  P1G19 

STOP READY Mode Edit Accept

P3.4.1.1. I/O term change value value

Motor Nom Volt

400 V enter

7
©2015 Konecranes Plc. All right reserved 7
 Parameters saving on a display

• S6.3 Parameters copy:

RUN ST O P READY ALARM FAULT • S6.3.2 From the drive to the display
S6.3 I/O term Ke ypa d Bus/C omm
– All active parameters are saved in a
Copy Parameters display
P1->P4 -> • S6.3.3 From the display to the drive
– All parameters from the display are saved
run fau lt
as active parameters in the drive
rea dy
S TA RT
reset

S TO P

select enter

8
©2015 Konecranes Plc. All right reserved 8
 Monitoring

• PROFIBUS DP status • Multimonitor

• Fault counter
• Speed Supervision Unit settings
• Motor operating parameters
RUN STOP READY ALARM FAULT
• Analog inputs/outputs and relay N4.21.1 I/O term Keypad Bus/Comm

outputs status and values

10.0 A 400.0 V
50.00 Hz
ready run fault
START
reset

STOP

select enter

9
©2015 Konecranes Plc. All right reserved 9
 Parameters groups

+ sign in the front of the Group code means that group is visible in panel, when group function is selected. – According to the password access
G3 Parameters
G3.1 Basic Parameter
different parameters groups can be
G3.2 I/O Parameters changed ;
G3.2.1 Digital Inputs
G3.2.2 Analog Input 1
G3.2.3 Analog Input 2
+ G3.2.3.7 AU-Speed Ref – You can view only the groups that are
+ G3.2.3.8 Torque Reference
+ G3.2.3.9 Speed Correction allowed by your password access;
+ G3.2.3.10 Torque Limit
+ G3.2.3.11 Load Feedback
G3.2.4 Analog Output
G3.2.4.1 Aout1 Function – List of all parameters can be found in
G3.2.4.2 Aout2 Function
G3.2.5 Relay Outputs parameter manual.
G3.3 Drive Control
G3.3.6 Limit Functions
+ G3.3.7 Ramp2
G3.3.8 Advanced Ramps
+ G3.3.9 Multistep
+ G3.3.10 SSU
G3.3.11 Prohib Freq
+ G3.3.12 Multicare
G3.3.12.1 Multicare 1
G3.3.12.2 Multicare 2
G3.3.13 Torque Control
G3.3.14 Load Control

10
©2015 Konecranes Plc. All right reserved 10
 Access levels and passwords

• Full list of the parameters and required access level can be found in
a Drive Parameters Manual.
• Level 1 – Access denied- password 0
• Level 2 – Start-up - password 26
• Level 3 – Engineering- password 768

– password 2419

11
©2015 Konecranes Plc. All right reserved 11
 Access level for start-up

• Give access to the main parameters used during the start-up;

• Displayed parameters groups vary depending on selected functions.

Example of displaying of parameters groups for open loop system

G3 Parameters
G3.1 Basic Parameter
G3.2 I/O Parameters
G3.2.2 Analog Input 1
G3.2.3 Analog Input 2
G3.4 Motor Parameter
G3.4.1 Motorset 1
+ G3.4.2 Open Loop 1
G3.4.2.1 U/f Curve

12
©2015 Konecranes Plc. All right reserved 12
 Engineering access level

«+» before the group means that the group will be shown, when its’ function is activated

G3 Parameters
G3.1 Basic Parameter
G3.2 I/O Parameters
G3.2.1 Digital Inputs
G3.2.2 Analog Input 1
G3.2.3 Analog Input 2
+ G3.2.3.7 AU-Speed Ref Example of
G3.2.4 Analog Output
G3.2.4.1 Aout1 Function
displaying of
G3.2.4.2 Aout2 Function parameters groups
G3.2.5 Relay Outputs
G3.3 Drive Control for closed loop
G3.3.6 Limit Functions system
G3.3.8 Advanced Ramps
+ G3.3.10 SSU
G3.3.11 Prohib Freq
G3.3.13 Torque Control
G3.3.14 Load Control
G3.4 Motor Parameter
G3.4.1 Motorset 1
G3.4.1.20 Additional
G3.4.1.21 ESR
+ G3.4.3 Closed Loop 1
G3.4.6.5 Brake Control
G3.6 Protection

13
©2015 Konecranes Plc. All right reserved 13
 S6 System Menu

• Includes drive system information. Also shows menus that are not
supported by crane software.
• Copy Parameters: Up to Keypad, Down from Keypad;
• Parameters Comparison;
• Keypad settings;
• System Info;

14
©2015 Konecranes Plc. All right reserved 14
 NOT JUST LIFTING
THINGS, BUT ENTIRE
BUSINESSES

15
©2015 Konecranes Plc. All right reserved 15