A Study On Micromachining and Effects of Cryogenic Treatment On Micro End Mill Cutters
A Study On Micromachining and Effects of Cryogenic Treatment On Micro End Mill Cutters
A Study On Micromachining and Effects of Cryogenic Treatment On Micro End Mill Cutters
Abstract: The research in micromachining has been started from last decade. The demand of microcomponent
and microproduct is increasing progressively in electronics, optics, medical and automobile sectors. As
machining dimensions diminishes from macro to micro, machining conditions varies which affect tool life,
cutting forces and surface machined. Numerous efforts are in progress which attempts to enhance the tool
performance. Cryotretment of cutting tools gives improved hardness, strength and wear resistance due to the
precipitation of η (eta) carbide in metal matrix. In macromachining cryotreated tools performed well and
ample of literature is available while the applications of cryotreatment for micro cutting tools, its
characterization and performance are emerging area. In present paper the effects of cryotreatment on micro
end mill cutters have been investigated.
Keywords : Micromachining, Cryotreatment, Tungsten Carbide, Size Effects
I. Introduction
The demand of micro component is increasing in aerospace, biomedical and automobile industry. It has
been found that, photolithography base micromanufacturing techniques have some limitation regarding use of
material as it is applicable only for silicon, copper and Ni alloys. Micro cutting have some solution to overcome
the limitation of photolithography process. Improving the life of micro cutting tool is the requirement of micro
machining. [6]
Size effect, material homogeneity, minimum chip thickness these are the some concepts which
differentiate micromachining from macromachining. In the study it has been found that, in micromachining the
rapid tool wear generates higher cutting forces and this deteriorates surfaces. It is expected by improving tool
life, the performance of micromachining can be improved. A few approaches have been proposed to overcome
the tool failure and to make micromachining (preferably cutting) more suitable. The first approach involves the
use of cutting fluids to provide cooling and lubrication. However, it is very difficult to transport the cutting fluid
to the cutting zone and tool-workpiece interfaces due to the high cutting speeds and the small size of the contact
zone. This limitation is also true to a great extent in macroscale machining.
The second approach involves the application of coatings on the micro tool surfaces to reduce wear.
This approach is routinely adopted at the macroscale to enhance tool life. Although a few researchers have
demonstrated that coatings prolong micro tool life to an extent but coatings become futile once it gets removed
from the substrate. In the third approach; hybrid machining, for e.g. laser assisted micromachining, some
researcher reported that poor surfaces while machining along with high set up cost. While considering the above
issue the fourth approach is there i.e. Cryogenic treatment of cutting tools.
Cryogenic treatment, which is also known as sub-zero heat treatment, has made significant
contributions to the improvement of wear resistance, tool life and dimensional integrity. Moreover, in cryogenic
treatment the formation of martensite and precipitation of η- phase is body phenomena so gives better hardness
and wear resistance than coating on cutting tool.
In contrast to macromachining, de-burring, size effects, minimum chip thickness due to grain size,
hardness, impurities, homogeneities, defects in workpiece affects micromachining processes dominantly. When
complicated parts are machined, cutting tool radius immediately chip-off due to tool wear, so tool life
improvement is essential to make micro cutting easier [9]. This paper thus aimed at critical review of cryogenic
treatment of specifically micromachining tools. It has been observed that that, the applications of cryogenic
treatment for micro cutting tool, its characterization and performance analysis is nascent area for
micromachining. Further, a very little work of cryotreated cutting tool has been found in micro cutting.
Figure 1: Hard tungsten carbide skeleton and soft cobalt binder form a composite of WC-Co [4].
The following phases are generally present in metallographic microstructure of cemented tungsten
carbides:
Table 1: Phases in WC-Co [4]
The formation of η phase while cryogenic treatment gives the improved tool life and better abrasive
wear resistance to tungsten carbide tool. It has been found that the proportion of η phase increases while cryo
treatment and it act as filler in the larger carbide. As η phase is harder than the rest of the material, it enhances
the fracture toughness of the cutting tool. The growth of η phase depends on the selection of cryogenic
parameter so it will give optimum hardness [3].
According to Gill et. al. (2012) hard phase particles of tungsten carbide are refined into their most
stable form via the phenomenon of spherodization. It also aligns the hard phase carbide particulate structure into
a durable, stress-free crystallographic configuration. This reduces the risk of stress-induced fractures. The fine
eta (η) carbide particles precipitate during the cryogenic treatment. These are in addition to the larger carbide
particles present before cryogenic treatment. These fine particles act as fillers along with the larger particles to
form a denser, more coherent, and much tougher matrix in the material. At the same time cryogenic treatment
relieve the residual micro stresses in the tools while sintering process which is main cause for tool failure [1, 4,
8].
Cryogenic treatment applied at temperature -80˚C to -140 ˚C is termed as shallow treatment while,
temperature between -140˚C to -196˚C is termed as deep cryogenic treatment. To study the effects of both, i.e.
Shallow (SCT) and deep (DCT), both temperatures taken for study 8 hr soaking period. Applied cryo-cycles on
micro end mills is as shown in Table 2.
Liquid nitrogen is used for cryotreatment of cutting tools followed by tempering treatment at 150˚C for
2 hr. The purpose of tempering is to relieve the internal stresses of tools. Figure 3 shows the set-up of cryogenic
treatment and tempering furnace respectively.
2020
2000
Vivkers Hardness
1980
1960
1940
HV 0.5
1920
1900
1880
Untreated SCT 8 DCT 8
Soaking Temprature
It has been found that, the microhardness value increased for both shallow and deep cryotreatment as
compare to untreated tool. This might be attributed to formation of new η carbide in metal matrix and
refinement of grain structure. The highest microhardness valueis obtained for deep cryotreated for 8 hour (-
180ºC). This shows that as temperature reduces the rate of precipitation increases.
Scanning electron microscope images are taken to observe the microstructure of micro tungsten carbide
end mill cutters. Figure 4 (a-c) shows the SEM images of untreated shallow cryotreated for 8 hour and deep
cryotreated for 8 hr.
(a) (b)
(c)
Figure 4: SEM images of (a) untreated (b) SCT 8 (c) DCT 8
From figure 4 (b) (c) it is clear that the size of α phase (tungsten carbide ) particle increased after cryogenic
treatment , this might be attributed to increase the hardness of micro end mills after cryogenic treatment.
V. Conclusions
From the experimental work following conclusion can be drawn:
1) Cryogenic treatment improves the mechanical properties of conventional tools.
2) Size effects, material homogeneity and minimum chip thickness are phenomenon which differentiate
micromachining from macromachining
3) The hardness of micro tungsten carbide tools increased after cryotreatment.
4) It is found that, the size of α phase particle increased after cryotreatment, this might be reason to increase the
hardness of microtools.
References
[1]. Nursel Altan Özbek, Adem Çiçek,, Mahmut Gülesin, Onur Özbek, ―Investigation of the effects of cryogenic treatment applied at
different holding times to cemented carbide inserts on tool wear ‖, International Journal of MachineTools &
Manufacture86(2014)34–43, (2014).
[2]. Simranpreet Singh Gill, Harpreet Singh , Rupinder Singh &,Jagdev Singh, ―Cryoprocessing of cutting tool materials—a review‖,
International Journal Advance Manufacturing Technology, (2010) 48:175–192, , (2010).
[3]. Sıtkı Akincioğlu and Hasan Gökkaya and İlyas Uygur, ―A review of cryogenic treatment on cutting tools‖, International Journal
Advance Manufacturing Technology, January 2015 .
[4]. Simranpreet Singh Gill , Jagdev Singh , Rupinder Singh and Harpreet Singh, ―Metallurgical principles of cryogenically treated tool
steels—a review on the current state of science‖, International Journal Advance Manufacturing Technology ,(2011) 54:59–82,
(2011).
[5]. A. Y. L. Yong. K. H. W. Seah . M. Rahman, ―Performance of cryogenically treated tungsten carbide tools in milling operations‖,
Int. Journal Advance Manufacturing Technology (2007) 32: 638–643, (2007).
[6]. Petar Piljek, Zdenka Keran and Miljenko Math‖ micromachining – review of literature from 1980 to 2010‖, Interdisciplinary
Description of Complex Systems 12(1), 1-27, 2014.
[7]. Shreyas T. Dhande, Vijay A. Kane, Chandrashekhar L. Gogte, ― Cryogenic Treatment of Tungsten Carbide Tools: Review ‖,
International Journal of Science and Research (IJSR) ISSN (Online): 2319-7064, (2014).