Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Instruction Sheet Is Rfv5008: - Style Number Rfv5008Hp:: Package Contents

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

INSTRUCTION SHEET : IS - RFV5008

STYLE NUMBER : RFV5008HP


6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445
www . quoizel . com

PACKAGE CONTENTS ISSUED 10- 20 09

Part Description Quantity


A Crossbar 1pc A
B Green Ground Screw 1pc
C Lock Washer 2pcs B
D Hex Nut 2pcs
C
E Nipple 1pc
Ceiling Canopy D
F 1pc
G Canopy Lock Ring 1pc E
H Ceiling Canopy Loop 1pc K
Fixture Chain 1pc F
I
J Fixture Assembly 1pc
K Center Column Assembly 1pc
G

! WARNINGS AND CAUTIONS


WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.

PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time : 30 - 45 minutes
● Tools Required for Assembly (not included) : Flathead Screwdriver , Phillips Screwdriver, Pliers,
Electrical Tape, Wire Cutters, Safety Glasses &8, 60 Watt, Type - B Cand Base Bulbs.
● Helpful Tools (not included) : Wire Strippers.

1 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER : RFV5008HP

STEP 1 :
a . Thread the end of the Center Column Assembly into the
center of the Fixture Assembly and hand tighten until
snug.

Center Column
Assembly

Fixture Assembly

STEP 2 :
a . Secure the Crossbar onto the Outlet Box with Outlet
Box Screws . Tighten until snug . Outlet Box

Crossbar

Outlet Box
Screw

STEP 3 :
* Pliers is required on this step .
a . Thread one Hex Nut onto top end of the Nipple .
b . Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of Lock Washer
the Crossbar . Crossbar
Hex Nut
c . Using pliers , thread the Hex Nut against the Crossbar
and hand tighten until snug .
d . Thread another Hex Nut onto the bottom end of the
Nipple . Nipple

Hex Nut

2 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER : RFV5008HP

STEP 4 :
a . Adjust the Fixture Chain to your desired length by
removing the links if needed .
* Please note that depends on chain material Nipple
thickness , you might be required to use chain pliers to Hex Nut
spread links open .
b . Pull the supply wires through the Fixture Chain Lock Washer
alternating links . And then pull the wires through the Canopy Chain Loop
following components in turn :
Canopy Lock Ring , Ceiling Canopy , Canopy Chain
Loop , Lock Washer , and Nipple .
c . Place Lock Washer over the end of the Nipple and
Ceiling Canopy
thread the Canopy Chain Loop onto the end of the
Nipple .
d . Using pliers , thread the Hex Nut against the Canopy
Chain Loop and tighten until snug . Fixture Chain
e . Attach one end of the Fixture Chain onto the Fixture
Loop and attach the another end of the chain onto the
Canopy Chain Loop .
f . Refer to Step 5 - Wire Connections to connect wires . Canopy Lock Ring
g . Push the Ceiling Canopy upward over the Outlet Box .
h . Thread the Canopy Lock Ring onto the Canopy Chain Fixture Loop
Loop and tighten until snug to secure the Ceiling
Canopy .

STEP 5 :
* Use Wire Connectors ( not supplied ) to connect the WHITE OR RIBBED WHITE OR RIBBED
wires . FROM HOUSE FROM FIXTURE
a . Connect the House Ground Wire to the Fixture Ground
Wire.
b . Connect the House White ( or Ribbed ) Wire to the BLACK ( OR RED ) WIRE BLACK OR SMOOTH
Fixture Supply Wire ( White or Ribbed Side ) .
c . Connect the House Black ( or Red ) Wire to the Fixture FROM HOUSE FROM FIXTURE
Supply Wire ( Black or Smooth Side ).
d . Wrap each connection with approved electrical tape
GROUND WIRE GROUND WIRE
and carefully stuff all of the connected wires into the
Outlet Box . FROM HOUSE FROM FIXTURE

STEP 6 :
a . Install correct Bulbs referring to fixture markings and / or labels for maximum wattage .

Your installation is completed now . Restore electricity . Retain this sheet for future reference .

3 OF 4
Photograph STYLE NUMBER : RFV5008HP

4 OF 4

You might also like