Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

Features General Description

n Wide 4.5V to 40V Input Voltage Range The XL1507 is a 150 KHz fixed frequency
n 5V and adjustable versions PWM buck (step-down) DC/DC converter,
n Output Adjustable from 1.23V to 37V capable of driving a 3A load with high
n Maximum Duty Cycle 100% efficiency, low ripple and excellent line and
n Minimum Drop Out 1.5V load regulation. Requiring a minimum
n Fixed 150KHz Switching Frequency number of external components, the regulator
n 3A Constant Output Current Capability is simple to use and include internal
n Internal Optimize Power Transistor frequency compensation and a
n High efficiency fixed-frequency oscillator.
n Excellent line and load regulation
n TTL shutdown capability
The PWM control circuit is able to adjust the
n ON/OFF pin with hysteresis function
duty ratio linearly from 0 to 100%. An enable
n Built in thermal shutdown function
function, an over current protection function
n Built in current limit function
is built inside. When second current limit
n Built in second current limit function
function happens, the operation frequency
n Available in TO-252 package
will be reduced from 150KHz to 50KHz. An
internal compensation block is built in to
minimize external component count.
Applications
n LCD Monitor and LCD TV
n Digital Photo Frame
n Set-up Box
n ADSL Modem
n Telecom / Networking Equipment

Figure1. Package Type of XL1507 (TO252-5L)

Rev 2.0 www.xlsemi.com

1
 Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

Pin Configurations (TO252-5L)

Figure2. Pin Configuration of XL1507 (Top View)

Table 1 Pin Description

Pin Number Pin Name

Description
Supply Voltage Input Pin. XL1507 operates from a 4.5V to
1 VIN 40V DC voltage. Bypass Vin to GND with a suitably large
capacitor to eliminate noise on the input.
Power Switch Output Pin (SW). Output is the switch node that
2 OUTPUT
supplies power to the output.
Ground Pin. Care must be taken in layout. This pin should be
placed outside of the Schottky Diode to output capacitor
3 GND
ground path to prevent switching current spikes from inducing
voltage noise into XL1507.
Feedback Pin (FB). Through an external resistor divider
4 FEEDBACK network, Feedback senses the output voltage and regulates it.
The feedback threshold voltage is 1.23V.
Enable Pin. Drive ON/OFF pin low to turn on the device, drive
5 ON/OFF
it high to turn it off. Floating is default low.

Rev 2.0 www.xlsemi.com

2
 Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

Function Block

Figure3. Function Block Diagram of XL1507

Typical Application Circuit

FEEDBACK L1 33uh/3A
4
VIN OUTPUT 5V/3A
1 XL1507-5.0 2
3 5
COUT
GND ON/OFF
+12V CIN C1 LOAD
OFF D1 330uf 35V
470uf 35V 105 1N5820
ON

Figure4. XL1507 Typical Application Circuit 12V-5V/3A

Rev 2.0 www.xlsemi.com

3
 Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

Ordering Information

XL1507 E1
E1: Lead Free

Circuit Type

Version
ADJ: Adjust
5.0: 5V

Order Information Marking ID Package Type Packing Type Supplied As

XL1507-ADJE1 XL1507-ADJE1 TO252-5L 2500 Units on Tape & Reel
XL1507-5.0E1 XL1507-5.0E1 TO252-5L 2500 Units on Tape & Reel

XLSEMI Pb-free products, as designated with “E1” suffix in the par number, are RoHS compliant.

Rev 2.0 www.xlsemi.com

4
 Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

Absolute Maximum Ratings（Note1）

Parameter Symbol Value Unit
Input Voltage Vin -0.3 to 45 V
Feedback Pin Voltage VFB -0.3 to Vin V
ON/OFF Pin Voltage VON/OFF -0.3 to Vin V
Output Switch Pin Voltage VOutput -0.3 to Vin V
Power Dissipation PD Internally limited mW
Thermal Resistance (TO252)
RJA 50 ºC/W
(Junction to Ambient, No Heatsink, Free Air)
Operating Junction Temperature TJ -40 to 125 ºC
Storage Temperature TSTG -65 to 150 ºC
Lead Temperature (Soldering, 10 sec) TLEAD 260 ºC
ESD (HBM) 2000 V

Note1: Stresses greater than those listed under Maximum Ratings may cause permanent damage
to the device. This is a stress rating only and functional operation of the device at these or any
other conditions above those indicated in the operation is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.

Rev 2.0 www.xlsemi.com

5
 Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

XL1507-5.0 Electrical Characteristics

Ta = 25℃;unless otherwise specified.
Symbol Parameter Test Condition Min. Typ. Max. Unit

System parameters test circuit figure5

Output Vin = 7V to 40V
VOUT 4.8 5 5.2 V
Voltage Iload=0.2A to 3A
Vin=12V ,Vout=5V
Efficiency ŋ - 80 - %
Iout=3A
XL1507-ADJ Electrical Characteristics
Ta = 25℃;unless otherwise specified.
Symbol Parameter Test Condition Min. Typ. Max. Unit

System parameters test circuit figure5

Output Vin = 4.5V to 40V
VOUT 1.193 1.23 1.267 V
Voltage Iload=0.2A to 3A
Vin=12V ,Vout=3V
Efficiency ŋ - 73 - %
Iout=3A

Rev 2.0 www.xlsemi.com

6
 Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

Electrical Characteristics (DC Parameters)

Vin = 12V, GND=0V, Vin & GND parallel connect a 220uf/50V capacitor; Iout=500mA, Ta =
25℃; the others floating unless otherwise specified.
Parameters Symbol Test Condition Min. Typ. Max. Unit
Input operation voltage Vin 4.5 40 V
Shutdown Supply Current ISTBY VON/OFF=5V 80 200 uA
VON/OFF =0V,
Quiescent Supply Current Iq 2 10 mA
VFB =Vin
Oscillator Frequency Fosc 127 150 173 Khz

Switch Current Limit IL VFB =0 3.6 4.8 6.9 A

High (Regulator OFF) 1.4

ON/OFF Pin Threshold VON/OFF V
Low (Regulator ON) 0.8

ON/OFF Pin Input IH VON/OFF =2.5V (OFF) 5 15 uA

Leakage Current IL VON/OFF =0.5V (ON) 0.2 5 uA
VFB=0V
Output Saturation Voltage VCE 1.3 1.5 V
Iout=3A
Max. Duty Cycle DMAX VFB=0V 100 %

Rev 2.0 www.xlsemi.com

7
 Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

Test Circuit and Layout guidelines

Figure5. Standard Test Circuits and Layout Guides

Select R1 to be approximately 1K, use a 1% resistor for best stability.

C1 and CFF are optional; in order to increase stability and reduce the input power line noise, CIN
and C1 must be placed near to PIN1 and PIN3;
For output voltages greater than approximately 10V, an additional capacitor CFF is required. The
compensation capacitor is typically between 100 pf and 33 nf, and is wired in parallel with the
output voltage setting resistor, R2. It provides additional stability for high output voltage, low
input-output voltages, and/or very low ESR output capacitors, such as solid tantalum capacitors.
CFF=1/(31*1000*R2); This capacitor type can be ceramic, plastic, silver mica, etc. (Because of
the unstable characteristics of ceramic capacitors made with Z5U material, they are not
recommended.)

Rev 2.0 www.xlsemi.com

8
 Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

XL1507 Series Buck Regulator Design Procedure (Fixed Output)

Conditions Inductor Output Capacitor (COUT)

(L1) Through Hole Electrolytic Surface Mount Tantalum
Output Load Max Input Inductance Panasonic Nichicon AVX TPS Sprague
Voltage Current Voltage (V) (uh) HFQ Series PL Series Series 595D Series
(V) (A) (uf/V) (uf/V) (uf/V) (uf/V)
3.3 3 5 22 470/25 560/16 330/6.3 390/6.3
7 22 560/35 560/35 330/6.3 390/6.3
10 22 680/35 680/35 330/6.3 390/6.3
40 33 560/35 470/35 330/6.3 390/6.3
2 6 22 470/25 470/35 330/6.3 390/6.3
10 33 330/35 330/35 330/6.3 390/6.3
40 47 330/35 270/50 220/10 330/10
5 3 8 22 470/25 560/16 220/10 330/10
10 22 560/25 560/25 220/10 330/10
15 33 330/35 330/35 220/10 330/10
40 47 330/35 270/35 220/10 330/10
2 9 22 470/25 560/16 220/10 330/10
20 68 180/35 180/35 100/10 270/10
40 68 180/35 180/35 100/10 270/10
12 3 15 22 470/25 470/25 100/16 180/16
18 33 330/25 330/25 100/16 180/16
30 68 180/25 180/25 100/16 120/20
40 68 180/35 180/25 100/16 120/20
2 15 33 330/25 330/25 100/16 180/16
20 68 180/25 180/25 100/16 120/20
40 150 82/25 82/25 68/20 68/25

Rev 2.0 www.xlsemi.com

9
 Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

XL1507 Series Buck Regulator Design Procedure (Adjustable Output)

Output Through Hole Output Electrolytic Surface Mount Output Capacitor

Voltage Panasonic Nichicon Feedforward AVX TPS Sprague Feedforward
(V) HFQ Series PL Series Capacitor Series 595D Series Capacitor
(uf/V) (uf/V) (uf/V) (uf/V)
2 820/35 820/35 33nf 330/6.3 470/4 33nf
4 560/35 470/35 10nf 330/6.3 390/6.3 10nf
6 470/25 470/35 3.3nf 220/10 330/10 3.3nf
9 330/25 330/25 1.5nf 100/16 180/16 1.5nf
12 330/25 330/25 1nf 100/16 180/16 1nf
15 220/25 220/35 680pf 68/20 120/20 680pf
24 220/35 150/35 560pf 33/25 33/25 220pf
28 100/50 100/50 390pf 10/35 15/50 220pf

Schottky Diode Selection Table

Current Surface Through VR (The same as system maximum input voltage)

Mount Hole
20V 30V 40V 50V 60V
1A √ 1N5817 1N5818 1N5819

√ 1N5820 1N5821 1N5822

√ MBR320 MBR330 MBR340 MBR350 MBR360
√ SK32 SK33 SK34 SK35 SK36
3A
√ 30WQ03 30WQ04 30WQ05
√ 31DQ03 31DQ04 31DQ05
√ SR302 SR303 SR304 SR305 SR306

√ 1N5823 1N5824 1N5825

√ SR502 SR503 SR504 SR505 SR506
5A
√ SB520 SB530 SB540 SB550 SB560
√ 50WQ03 50WQ04 50WQ05

Rev 2.0 www.xlsemi.com

10
 Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

Typical System Application for 5V Version

FEEDBACK L1 33uh/3A
4
VIN OUTPUT 5V/3A
1 XL1507-5.0 2
3 5
COUT
GND ON/OFF
+12V CIN C1 LOAD
OFF D1 330uf 35V
470uf 35V 105 1N5820
ON

Figure7. XL1507-5.0 System Parameters Test Circuit

Typical System Application for ADJ Version

CFF 10n

R1 1K R2 3.1K

FEEDBACK L1 47uh/3A
4
VIN OUTPUT 5V/3A
1 XL1507-ADJ 2
3 5
COUT
GND ON/OFF
+24V CIN C1 LOAD
OFF D1 470uf 35V
470uf 50V 105 1N5821
ON

VOUT=1.23*(1+R2/R1)

Figure9. XL1507-ADJ System Parameters Test Circuit

Rev 2.0 www.xlsemi.com

11
 Datasheet

3A 150KHz 40V Buck DC to DC Converter XL1507

Package Information
TO252-5L

Rev 2.0 www.xlsemi.com

12