Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Datasheet 2A 380Khz 18V Buck DC To DC Converter Xl1410 Features General Description

Download as pdf or txt
Download as pdf or txt
You are on page 1of 9

Datasheet

2A 380KHz 18V Buck DC to DC Converter XL1410

Features General Description


n Wide 3.6V to 18V Input Voltage Range The XL1410 is a 380KHz fixed frequency
n Output Adjustable from 1.222V to 16V PWM buck (step-down) DC/DC converter,
n Maximum Duty Cycle 100% capable of driving a 2A load with high
n Minimum Drop Out 0.6V efficiency, low ripple and excellent line and
n Fixed 380KHz Switching Frequency load regulation. Requiring a minimum
n 2A Constant Output Current Capability number of external components, the regulator
n Internal Optimize Power MOSFET is simple to use and include internal
n High efficiency frequency compensation and a
n Excellent line and load regulation
fixed-frequency oscillator.
n TTL shutdown capability
n EN pin with hysteresis function
The PWM control circuit is able to adjust the
n Built in thermal shutdown function
duty ratio linearly from 0 to 100%. An enable
n Built in current limit function
function, an over current protection function
n Built in output short protection function
is built inside. When short protection function
n Available in SOP8 package
happens, the operation frequency will be
reduced from 380KHz to 80KHz. An internal
compensation block is built in to minimize
Applications
external component count.
n LCD Monitor and LCD TV
n Digital Photo Frame
n Set-up Box
n ADSL Modem
n Telecom / Networking Equipment

Figure1. Package Type of XL1410

Rev 1.0 www.xlsemi.com


1
Datasheet

2A 380KHz 18V Buck DC to DC Converter XL1410

Pin Configurations

Figure2. Pin Configuration of XL1410 (Top View)


Pin Number Pin Name Description
1,6,8 NC No Connected.
Supply Voltage Input Pin. XL1410 operates from a 3.6V to 18V
2 VIN DC voltage. Bypass Vin to GND with a suitably large capacitor
to eliminate noise on the input.
Power Switch Output Pin (SW). Output is the switch node that
3 SW
supplies power to the output.
Ground Pin. Care must be taken in layout. This pin should be
placed outside of the Schottky Diode to output capacitor ground
4 GND
path to prevent switching current spikes from inducing voltage
noise into XL1410.
Feedback Pin (FB). Through an external resistor divider
5 FB network, Feedback senses the output voltage and regulates it.
The feedback threshold voltage is 1.222V.
Enable Pin. Drive EN pin low to turn off the device, drive it
7 EN
high to turn it on. Floating is default high.
Function Block

Figure3. Function Block Diagram of XL1410

Rev 1.0 www.xlsemi.com


2
Datasheet

2A 380KHz 18V Buck DC to DC Converter XL1410

Typical Application Circuit

CFF 33n

R1 R2
2K 6.2K
FB L 33uh/2A
5
VIN SW VOUT 5V/2A
2 XL1410 3
4 7
GND EN
COUT LOAD
+12V CIN C1 D1 1N5821
ON 220uf/35V
220uf/35V 105
OFF

12V ~ 5V/2A
VOUT=1.222*(1+R2/R1)

Figure4. XL1410 Typical Application Circuit

System Efficiency Curve

Rev 1.0 www.xlsemi.com


3
Datasheet

2A 380KHz 18V Buck DC to DC Converter XL1410

Ordering Information

Order Information Marking ID Package Type Packing Type Supplied As


XL1410E1 XL1410E1 SOP-8L 2500 Units on Tape & Reel

XLSEMI Pb-free products, as designated with “E1” suffix in the par number, are RoHS compliant.

Absolute Maximum Ratings(Note1)


Parameter Symbol Value Unit
Input Voltage Vin -0.3 to 20 V
Feedback Pin Voltage VFB -0.3 to Vin V
EN Pin Voltage VEN -0.3 to Vin V
Output Switch Pin Voltage VOutput -0.3 to Vin V
Power Dissipation PD Internally limited mW
Thermal Resistance (SOP8)
RJA 100 ºC/W
(Junction to Ambient, No Heatsink, Free Air)
Operating Junction Temperature TJ -40 to 125 ºC
Storage Temperature TSTG -65 to 150 ºC
Lead Temperature (Soldering, 10 sec) TLEAD 260 ºC
ESD (HBM) 2000 V

Note1: Stresses greater than those listed under Maximum Ratings may cause permanent damage
to the device. This is a stress rating only and functional operation of the device at these or any
other conditions above those indicated in the operation is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.

Rev 1.0 www.xlsemi.com


4
Datasheet

2A 380KHz 18V Buck DC to DC Converter XL1410

XL1410 Electrical Characteristics


Ta = 25℃;unless otherwise specified.
Symbol Parameter Test Condition Min. Typ. Max. Unit

System parameters test circuit figure4


Feedback Vin = 7V to 18V, Vout=5V
VFB 1.186 1.222 1.258 V
Voltage Iload=0.2A to 2A
Vin=12V ,Vout=5V
Efficiency ŋ - 89 - %
Iout=2A

Electrical Characteristics (DC Parameters)


Vin = 12V, GND=0V, Vin & GND parallel connect a 220uf/50V capacitor; Iout=500mA, Ta =
25℃; the others floating unless otherwise specified.
Parameters Symbol Test Condition Min. Typ. Max. Unit
Input operation voltage Vin 3.6 18 V
Shutdown Supply Current ISTBY VEN=0V 60 200 uA
VEN =2V,
Quiescent Supply Current Iq 3 5 mA
VFB =Vin
Oscillator Frequency Fosc 323 380 437 Khz

Switch Current Limit IL VFB =0 4 A

High (Regulator ON) 1.4


EN Pin Threshold VEN V
Low (Regulator OFF) 0.8

EN Pin Input Leakage IH VEN =2V (ON) 1 15 uA


Current IL VEN =0V (OFF) 1 15 uA

Max. Duty Cycle DMAX VFB=0V 100 %

Rev 1.0 www.xlsemi.com


5
Datasheet

2A 380KHz 18V Buck DC to DC Converter XL1410

Test Circuit and Layout guidelines

Figure5. Standard Test Circuits and Layout Guides

Select R1 to be approximately 2K, use a 1% resistor for best stability.


C1 and CFF are optional; in order to increase stability and reduce the input power line noise, CIN
and C1 must be placed near to VIN and GND;
For output voltages greater than approximately 10V, an additional capacitor CFF is required. The
compensation capacitor is typically between 100 pf and 33 nf, and is wired in parallel with the
output voltage setting resistor, R2. It provides additional stability for high output voltage, low
input-output voltages, and/or very low ESR output capacitors, such as solid tantalum capacitors.
CFF=1/(31*1000*R2); This capacitor type can be ceramic, plastic, silver mica, etc. (Because of
the unstable characteristics of ceramic capacitors made with Z5U material, they are not
recommended.)

Rev 1.0 www.xlsemi.com


6
Datasheet

2A 380KHz 18V Buck DC to DC Converter XL1410

Schottky Diode Selection Table

Current Surface Through VR (The same as system maximum input voltage)


Mount Hole
20V 30V 40V 50V 60V
1A √ 1N5817 1N5818 1N5819

√ 1N5820 1N5821 1N5822


√ MBR320 MBR330 MBR340 MBR350 MBR360
√ SK32 SK33 SK34 SK35 SK36
3A
√ 30WQ03 30WQ04 30WQ05
√ 31DQ03 31DQ04 31DQ05
√ SR302 SR303 SR304 SR305 SR306

Rev 1.0 www.xlsemi.com


7
Datasheet

2A 380KHz 18V Buck DC to DC Converter XL1410

Typical System Application for 12V ~ 5V/2A Version

CFF 33n

R1 R2
2K 6.2K
FB L 33uh/2A
5
VIN SW VOUT 5V/2A
2 XL1410 3
4 7
GND EN
COUT LOAD
+12V CIN C1 D1 1N5821
ON 220uf/35V
220uf/35V 105
OFF

12V ~ 5V/2A
VOUT=1.222*(1+R2/R1)

Figure6. XL1410 System Parameters Test Circuit (12V ~ 5V/2A)

Typical System Application for 12V ~ 3.3V/2A

CFF 33n

R1 R2
2K 3.4K
FB L 33uh/2A
5
VIN SW VOUT 3.3V/2A
2 XL1410 3
4 7
GND EN
COUT LOAD
+12V CIN C1 D1 1N5821
ON 220uf/35V
220uf/35V 105
OFF

12V ~ 3.3V/2A
VOUT=1.222*(1+R2/R1)

Figure7. XL1410 System Parameters Test Circuit (12V ~ 3.3V/2A)

Rev 1.0 www.xlsemi.com


8
Datasheet

2A 380KHz 18V Buck DC to DC Converter XL1410

Package Information

SOP8 Package Mechanical Dimensions

Rev 1.0 www.xlsemi.com


9

You might also like