Module 15 Question Bank

EASA PART 66 QUESTION BANK
MODULE 15: GAS TURBINE ENGINE
A COMPILATION OF
PART 66 BLOGSPOT WEBSITE QUESTIONS
MODULE 15: GAS TURBNE ENGINE
PREFACE
This question bank is a compilation of MCQ questions for EASA Part 66 Module 15 (Gas Turbine
Engine) as per Part66Blogsport website. The compilation is in a reader friendly format with only
the questions and answers for quick revisions and reduced volume.
For a complete preparation, thoroughly studying a Gas Turbine Engine text book (Recommended
list is as follows) is inescapable. However, I have found that going through this question bank will
give the student an idea about the gigantic syllabus and focus important areas from the text book.
I prepared this compilation for my own exam and found the strategy fruitful.
This question bank is by no means a suggestion / shortlist. Rather, this can be a good starting
point for students who are planning to prepare for the exam to have a feel of the question standard
and difficulty.
For question standards and examination policy, local regulatory requirements should be followed.
For Bangladesh, ANO Part 66 available in CAAB website may be referred.
This document was drafted only as a personal study material, hence advance apologies for any
typo / formatting errors. However, I would be delighted if it comes to good use of anyone sitting
for Module 15 exams.
All the Best wishes for aspirant readers.
Regards,
Md. Mijanur Rahman
AME # BD.66.0654
B.Sc. Engg. (Aeronautical - MIST), EMBA – IBA, DU
2
SUGGESTED STUDY MATERIALS
The following is a list of publications which may be useful when studying for Module 15 (Gas
Turbine Engine) examinations in support of ANO (AW) Part-66 maintenance license.
Book Title Author ISBN

The Jet Engine Rolls Royce 0-902-121235
Aircraft Powerplants Bent & Mckinley 0-07-035569-X
Aircraft Powerplants Kroes. Wild 0-07-113429-6
ASA – AMT – P Dale Crane 1-56027-410-7
Aircraft Gas Turbine Engine Technology I. E. Treager 0028018281
Aircraft Gas Turbine Engine Technology I. E. Treager 007065199X
Ref: CAAB ANO Part 66 Guidance Material
3
TABLE OF CONTENTS
SECTION TOPIC
15.1 GAS Turbine Engine Fundamentals.
15.2 Engine Performance
15.3 Engine Inlet
15.4 Engine Compressors.
15.5 Combustion Section.
15.6 Turbine Section.
15.7 Engine Exhaust.
15.8 Bearings and Seals.
15.9 Lubricants and Fuels.
15.10 Lubrication Systems.
15.11 Fuel Systems.
15.12 Air Systems.
15.13 Starting and Ignition Systems.
15.14 Engine Indication Systems.
15.15 Power Augmentation Systems
15.16 Turbo-prop Engines
15.17 Turbo-Shaft Engines.
15.18 Auxiliary Power Units (APUs).
15.19 Powerplant Installation.
15.20 Fire Protection Systems
15.21 Engine Monitoring and Ground Operation.
15.22 Engine Storage and Preservation.
15.23 MISC
4
15.1 GAS TURBINE ENGINE Fundamentals.

>> Question Number. 1. On an axial flow, dual compressor forward fan engine, the fan turns the
same speed as the.
Correct Answer is. Low pressure turbine.
>> Question Number. 2. A turbo jet engine gives.
Correct Answer is. Large acceleration to a small mass of air.
>> Question Number. 3. The basic gas turbine engine is divided into two main sections: the cold
section and the hot section.
Correct Answer is. The hot section includes the combustor, turbine, and exhaust.
>> Question Number. 4. A jet engine derives its thrust by.
Correct Answer is. Reaction of the propelling gases.
>> Question Number. 5. Which of the following might be used to identify turbine discharge
pressure?
Correct Answer is. Pt7.
>> Question Number. 6. in a free turbine.
Correct Answer is. There is no mechanical connection with the compressor.
>> Question Number. 7. Bernoulli's Theorem states that at any point in a flow of gas.
Correct Answer is. The total energy remains constant.
>> Question Number. 8. The working fluid of a gas turbine engine is.
Correct Answer is. Air.
Explanation. Kerosene provides the energy to drive the air.
>> Question Number. 9. Which statements are true regarding aircraft engine propulsion?
Correct Answer is. An engine driven propeller imparts a relatively small amount of
acceleration to a large mass of air.
>> Question Number. 10. As subsonic air flows through a convergent nozzle the velocity.
Correct Answer is. Increases.
Explanation. Bernoulli's Theorem again.
>> Question Number. 11. In a twin spool compressor system, the first stage turbine drives them.
Correct Answer is. N2 compressor.
>> Question Number. 12. At what point in an axial flow turbojet engine will the highest gas
pressures occur?
Correct Answer is. At the compressor outlet.
>> Question Number. 13. Which of the following units are generally used to measure aircraft
noise?
5
Correct Answer is. Effective perceived noise decibels (E P N dB).

>> Question Number. 14. The diffuser section is located between.
Correct Answer is. The compressor section and the burner section.
>> Question Number. 15. If the LP shaft shears.
Correct Answer is... Turbine runaway occurs.
>> Question Number. 16. The term Pt7 means.
Correct Answer is... The total pressure at station No. 7.
>> Question Number. 17. What section provides proper mixing of the fuel and efficient burning of
the gases?
Correct Answer is... Combustion section only.
>> Question Number. 18. Of the following, which engine type would most likely have a noise
suppression unit installed?
Correct Answer is... Turbojet.
>> Question Number. 19. The pressure of supersonic air as it flows through a divergent nozzle.
Correct Answer is... Decreases.
>> Question Number. 20. The symbol for designating the speed of a LP compressor in a twin
spool engine is.
Correct Answer is... N1.
Explanation. N1 for LP N2 for H P.
>> Question Number. 21. A turbojet engine is smoother running than a piston engine because.
Correct Answer is... It has no reciprocating parts.
>> Question Number. 22. A gas turbine engine comprises which three main sections?
Correct Answer is... Turbine, compressor, and combustion.
>> Question Number. 23. When a volume of air is compressed.
Correct Answer is... No heat is lost or gained.
>> Question Number. 24. The pressure of subsonic air as it flows through a convergent nozzle.
Correct Answer is... Decreases.
>> Question Number. 25. If a volume of a mass of air is 546 cubic feet at 273K, at 274K it will be.
Correct Answer is... 2 cubic feet greater. (P1V1=P2V2)
>> Question Number. 26. In what section of a turbojet engine is the jet nozzle located?
Correct Answer is. Exhaust.
>> Question Number. 27. Newton's First Law of Motion, generally termed the Law of Inertia,
states:
6
Correct Answer is... Everybody persists in its state of rest, or of motion in a straight line,
unless acted upon by some outside force.
>> Question Number. 28. A high bypass engine results in.
Correct Answer is. Overall slower airflow and greater propulsive efficiency.
>> Question Number. 29. Bernoulli's Theorem states that at any point in a flow of gas.
Correct Answer is. The total energy remains constant.
>> Question Number. 30. The Brayton cycle is known as the constant.
Correct Answer is. Pressure cycle.
>> Question Number. 31. In a choked nozzle, velocity increases, and.
Correct Answer is. Pressure increases.
Explanation. As the nozzle goes sonic the pressure starts to increase as a result of the shock
wave.
>> Question Number. 32. Using standard atmospheric conditions, the standard sea level
temperature is.
Correct Answer is. 59°F.
>> Question Number. 33. Standard sea level pressure is.
Correct Answer is. 29.92 inches Hg.
>> Question Number. 34. The highest pressure in a gas turbine is.
Correct Answer is. Just after the last compressor stage but before the burner.
>> Question Number. 35. The velocity of subsonic air as it flows through a convergent nozzle.
>> Question Number. 36. A turboprop engine derives its thrust by.
Correct Answer is... Reaction of the prop-wash.
>> Question Number. 37. Adiabatic compression is.
Correct Answer is... one where there is no loss or gain of heat.
>> Question Number. 38. In a ducted fan engine, the fan is driven by the.
Correct Answer is... turbine.
>> Question Number. 39. A modular constructed gas turbine engine means that.
Correct Answer is. Its major components can be removed and replaced without disturbing
the rest of the engine.
Explanation. The Dictionary of Aircraft Terms by Dale Crane has this definition.
>> Question Number. 40. The accessory gearbox of a high bypass engine is.
Correct Answer is. On the HP Compressor housing.
>> Question Number. 41. On a gas turbine engine, what is the fan driven by?
7
Correct Answer is. LP turbine.

>> Question Number. 42. Which law relates to the kinetic, pressure, and potential energy in a
fluid?
Flow?
Correct Answer is. Bernoulli's theorem.
Explanation. The sum of the energies in a system is constant. So if one decreases another
will increase.
>> Question Number. 43. The density of gas may be expressed as.
Correct Answer is. Weight/volume.
Explanation. Basic Physics this one.
>> Question Number. 44. E S HP is.
Correct Answer is. Shaft horse power + exhaust efflux.
Explanation. Effective Shaft Horse Power is the measure of total power of a turbo prop
engine.
>> Question Number. 45. A divergent duct will cause subsonic flow to decrease in.
Correct Answer is. Velocity, increase pressure.
>> Question Number. 46. The Braydon cycle is.
Correct Answer is. The continuous combustion cycle taking place in a gas turbine engine.
Explanation. The Braydon Cycle is also known as the constant pressure cycle.
>> Question Number. 47. The purpose of a diffuser is to.
Correct Answer is. Increase the static pressure of the air.
Explanation. Diffusers are always static divergent ducts.
>> Question Number. 48. On a triple spool engine, the first stage of turbines drive.
Correct Answer is. The HP compressor.
>> Question Number. 49. Ram effect is.
Correct Answer is. Conversion of kinetic energy to pressure energy at the face of the
compressor.
Explanation. The greater the ram effect the greater the efficiency of the propulsion system.
>> Question Number. 50. Which of the following statements is true on a high bypass ratio
Turbofan?
Correct Answer is. Both the compressor and combustion chamber are smaller than their
turbojet equivalent.
Explanation. Smaller compressors and combustion chambers can be used on high bypass
fans as they are more efficient than turbo jets.
8
>> Question Number. 51. In the dual axial flow or twin spool compressor System with a free power
turbine, No would be an Indication of.
Correct Answer is. Free power turbine speed.
Explanation. The free turbine drives the prop-shaft only.
>> Question Number. 52. A wasted drive shaft is primarily to.
Correct Answer is. Provide a fuse if the driven component is overloaded.
Explanation. An example of this type of drive shaft is fitted between a gearbox and an I D G.
>> Question Number. 53. The 'core engine' or 'gas generator' is made up of the following
components:
Correct Answer is. Turbine, combustion chamber, compressor.
Explanation. The core engine is that which the primary airflow passes (the air that passes
through the combustion Chamber. The inlet is not included as the air is normally split down the
bypass duct at the entrance to the compressor System.
>> Question Number. 54. The principle of jet propulsion is.
Correct Answer is. Every action has an equal and opposite reaction.
Explanation. This is Newton’s Third Law.
>> Question Number. 55. Boyle's law states that, at constant temperature, if a gas is compressed.
Correct Answer is. Its absolute pressure is inversely proportional to its volume.
Explanation. If the volume is reduced the pressure goes up.
>> Question Number. 56. What part of a jet engine has the most potential energy?
Correct Answer is. Just before the combustion chamber.
Explanation. Where the fuel (unburned) is pumped in.
9
15.2 ENGINE PERFORMANCE.

>> Question Number. 1. Ram effect' due to aircraft forward speed will cause the efficiency of the
engine to.
Correct Answer is. Increase.
Explanation. Ram effect improves compression ratio which improves thrust without using
extra fuel
>> Question Number. 2. The efficiency of a gas turbine engine at altitude.
Explanation. The compressor performs better at lower air temperatures (see Jeppesen Gas
Turbines Page 2-33) thus improving thermal efficiency. Also lower air temperatures up to the
tropopause assist in maintaining Propulsive Efficiency (whilst accepting that decreasing density
decreases mass flow). Also note that operators fly at the tropopause whenever possible even for
short flights for the best SFC.
>> Question Number. 3. Which statement is true regarding jet engines?
Correct Answer is. At the higher engine speeds, thrust increases rapidly with small increases
in RPM.
>> Question Number. 4. Some turboprop and turbojet engines are equipped with two spool or
split compressors. When these engines are operated at high altitudes, the.
Correct Answer is. Low pressure rotor will increase in speed as the compressor load
decreases in the lower density air.
>> Question Number. 5. Ram effect' due to aircraft forward speed will cause the thrust of the
engine to.
Correct Answer is. Remain constant.
Explanation. Thrust is constant, but efficiency will increase.
>> Question Number. 6. With a fixed throttle, and with increased mass airflow, what happens to
EPR?
Correct Answer is. EPR goes down.
Explanation. With increasing mass airflow with throttles fixed, Ram pressure (Pt2) increases
but the P7 pressure remains the same.
>> Question Number. 7. At what stage in a gas turbine engine are gas pressures the greatest?
Correct Answer is. Compressor outlet.
>> Question Number. 8. Increasing ram effect with increased speed.
Correct Answer is. Increases thrust due to increased maximum airflow.
>> Question Number. 9. The highest heat to metal contact in a jet engine is the.
10
Correct Answer is. Turbine inlet guide vanes.

>> Question Number. 10. Which compressor type gives the greatest advantages for both starting
flexibility and improved high altitude performance?
Correct Answer is. Split spool, axial flow.
>> Question Number. 11. Which of the following is the ultimate limiting factor of turbine engine
operation?
Correct Answer is. Turbine inlet temperature.
>> Question Number. 12. At altitude, idling RPM is.
Correct Answer is. Higher than at sea level.
Explanation. Due to decreased density there is less resistance to rotation.
>> Question Number. 13. Thrust.
Correct Answer is. Increases with low temperature.
>> Question Number. 14. Which of the following variables affect the inlet air density of a turbine
engine?
Correct Answer is. Altitude of the aircraft, ambient temperature.
>> Question Number. 15. The propulsive efficiency is.
Correct Answer is. High, with a low mass flow acceleration.
Explanation. A large mass of air moved slowly!
>> Question Number. 16. The RPM for maximum power would be.
Correct Answer is. Lower on a colder day.
>> Question Number. 17. How does engine thrust vary with temperature?
Correct Answer is. Low temperature gives greater mass flow and therefore greater thrust.
>> Question Number. 18. A method of comparing engine efficiencies is by comparing.
Correct Answer is. Specific fuel consumption.
>> Question Number. 19. with a fixed throttle in a climb.
Correct Answer is. RPM will increase.
>> Question Number. 20. The point of maximum velocity in the engine is in the.
Correct Answer is. Exhaust exit nozzle.
>> Question Number. 21. At constant RPM, the pressure ratio of the compressor and the
temperature rise across the compressor.
Correct Answer is. Remains constant irrespective of height.
>> Question Number. 22. With the aircraft stationary, propulsive efficiency.
Correct Answer is. Is minimum.
11
>> Question Number. 23. The efficiency of conversion of kinetic energy into propulsive work is a
measure of.
Correct Answer is. Propulsive efficiency.
>> Question Number. 24. What effect does high atmospheric humidity have on the operation of a
jet engine?
Correct Answer is. Has little or no effect.
>> Question Number. 25. Power is adjusted in a gas turbine engine by.
Correct Answer is. Increasing air and fuel flow.
Explanation. You cannot have extra fuel without extra air.
>> Question Number. 26. The engine rating plug.
Correct Answer is. Is permanently connected to the Engine casing.
>> Question Number. 27. Flat Rated thrust is defined as.
Correct Answer is. The thrust at the ambient temperature point above which thrust drops
below 100%.
>> Question Number. 28. Thrust rating on an FADEC controlled engine can be changed by.
Correct Answer is. Changing the engine rating plug.
>> Question Number. 29. Propeller torque is analogous to.
Correct Answer is. Shaft horsepower.
Explanation. Propeller torque is equal and opposite of SHP under steady state conditions.
>> Question Number. 30. The total power in a turboprop engine is the.
Correct Answer is. E S HP.
Explanation. E S HP = shaft horse power plus residual gas exhaust thrust.
>> Question Number. 31. In a dive, with the throttles fixed, the EPR will.
Correct Answer is. Decrease.
>> Question Number. 32. With an increase in forward speed, the engine thrust.
Correct Answer is. Decreases slightly but recover due to ram effect.
>> Question Number. 33. The main factor considered when designing an engine is.
Correct Answer is. Maximum turbine temperature.
Explanation. The turbine is the most highly stressed component in the engine.
>> Question Number. 34. To ensure an engine maintains self-sustaining speed.
Correct Answer is. Idle increases with density decrease.
>> Question Number. 35. A factor that limits EGT is the.
Correct Answer is. Turbine.
Explanation. Rolls Royce the Jet Engine Page 13 refers.
12
>> Question Number. 36. Thrust will.

Correct Answer is. Increase at low temperatures.
Explanation. Higher density gives higher mass flow hence higher thrust.
>> Question Number. 37. Across the turbines, there is.
Correct Answer is. A general temperature drop.
Explanation. Rolls Royce the Jet Engine Page 15 shows a temperature decrease across the
turbines due to energy Extraction.
>> Question Number. 38. If the throttle position remains constant.
Correct Answer is. With increasing OAT, RPM and TGT will increase.
Explanation. As OAT increases the air is thinner RPM increases but thrust decreases due to
the thin air. Extra fuel is required to increase thrust therefore TGT increases.
>> Question Number. 39. If an aircraft climbs with a fixed throttle position.
Correct Answer is. Thrust decreases and RPM increases.
Explanation. Thinner air causes thrust to decrease and the compressor to speed up.
>> Question Number. 40. Ram pressure recovery will generally take effect at aircraft speeds of.
Correct Answer is. Mach 0.1 - 0.2.
Explanation. With the aircraft stationary and engines running intake pressure is negative. As
the aircraft begins its take off run the pressure recovers to above ambient (ram recovery.
>> Question Number. 41. As the air is passed through the turbine, due to the convergent shape
formed between adjacent Blades.
Correct Answer is. Pressure decreases, velocity increases, temperature decreases.
>> Question Number. 42. The hottest component in a gas turbine engine is.
Correct Answer is. The combustion chamber.
Explanation. Combustors have to withstand flame temperatures of 2000 degrees C.
>> Question Number. 43. The basic equation for thrust is.
Correct Answer is. Thrust = mass * acceleration.
Explanation. Newton’s second Law.
>> Question Number. 44. To maintain the selected RPM of a gas turbine at altitude.
Correct Answer is. The fuel will automatically be reduced as the aircraft climbs.
Explanation. In a hydro mechanical engine the P1 capsule will sense increasing altitude and
trim off the fuel.
>> Question Number. 45. The term Pub means.
Correct Answer is. Burner pressure measured at the combustion chamber.
13
Explanation. Burner pressure is the static pressure in the combustor can, used in some
systems to regulate fuel flow.
>> Question Number. 46. Which of the following is not an engine rating?
Correct Answer is. Idle.
>> Question Number. 47. At higher than standard day ambient temperatures, compressor speed
will be.
Correct Answer is. Higher than standard day speed.
Explanation. The air is thinner at higher temperatures, therefore the compressor has less
load to work against and goes faster. RR Jet Engine Fig 2-18 refers. Note that due to the max
allowable EGT the engine will reach a limiting 'corner-point Thrust' and fuel will be trimmed off to
prevent any over boost or over temperature
>> Question Number. 48. Ram Recovery' is a measure of.
Correct Answer is. Intake efficiency.
Explanation. Ram Recovery is the ability of an intake to convert kinetic energy into useful
pressure energy.
>> Question Number. 49. Most likely parameter limiting the height at which a jet engine powered
aircraft can operate
Would be insufficient.
Correct Answer is. Oxygen to support combustion.
Explanation. The engine will flame out with insufficient oxygen.
>> Question Number. 50. With increasing ram effect.
Correct Answer is. Propulsive efficiency increases.
Explanation. Increasing Ram Effect increases the overall system pressure ratio, hence
increasing propulsive efficiency.
>> Question Number. 51. Full reverse power is approximately.
Correct Answer is. 50% of forward thrust.
>> Question Number. 52. The efficiency of a gas turbine would be greatest at.
Correct Answer is. Cold temperatures
Explanation. Maximum thermal efficiency is achieved at the tropopause due to that being
the coldest ambient Temperature achievable.
>> Question Number. 53. in a gas turbine engine, turbine section.
Correct Answer is. Velocity increases and pressure decreases.
Explanation. Pressure and temperature always go down in the turbine as velocity goes up.
>> Question Number. 53. in a gas turbine engine, turbine section.
14

Explanation. Pressure and temperature always go down in the turbine as velocity goes up.
>> Question Number. 54. As air density changes the RPM of a gas turbine engine will change.
How is RPM kept at a Constant speed?
Correct Answer is. It is not.
Explanation. Whilst maximum RPM's are limited by various devices RPM is free to wander
with changing density. Egg As you Climb higher minimum idle will increase.
>> Question Number. 55. With fixed throttle and increasing altitude, the fan on a high by-pass
engine will.
Correct Answer is. Increase RPM.
>> Question Number. 56. through turbine rotor blades, the pressure.
Correct Answer is. Decreases, temperature and velocity decreases.
Explanation. (working cycle and airflow).
>> Question Number. 57. Temperature of the mass airflow through a Gas Turbine Engine.
Correct Answer is. Increases from the inlet, through the compressor and the diffuser into the
burner, and decreases through.
15
15.3 Engine Inlet

>> Question Number. 1. If an electrical de-icing system is operating, thrust will.
Correct Answer is. Remain constant.
Explanation. Hot air anti icing will reduce thrust, not electrical.
>> Question Number. 2. A bell mouth compressor inlet is used on.
Correct Answer is. Helicopters.
Explanation. Epperson Gas Turbine Power plant Page 3-5 refers.
>> Question Number. 3. Electrical de-icing operates.
Correct Answer is. Continuously and intermittently.
Explanation. Rolls Royce the Jet Engine page 150 refers.
>> Question Number. 4. The inlet door on a variable geometry intake is open at.
Correct Answer is. Subsonic speeds.
Explanation. Rolls Royce the Jet Engine fig 23.9 refers.
>> Question Number. 5. Anti-ice is recommended during.
. Correct Answer is. OAT +10°Centigrade and visible moisture.
Explanation. Epperson Gas Turbine Power plants Page 9-2 Refers.
>> Question Number. 6. A pilot intake is divergent from front to rear because it.
Correct Answer is. Produces the maximum amount of ram compression.
>> Question Number. 7. Anti-icing of jet engine air inlets is commonly accomplished by.
Correct Answer is. Engine bleed air ducted through the critical areas.
>> Question Number. 8. The term 'Ram Ratio' in regard to air intakes is the relationship between.
Correct Answer is. Ambient pressure and compressor inlet pressure.
>> Question Number. 9. An increase in the Ram Ratio of an intake will.
Correct Answer is. Decrease the temperature of the air.
>> Question Number. 10. As an aircraft approaches the transonic range, the aerodynamic
efficiency of a Piton type
Intake.
Correct Answer is. Decreases due to the shock wave.
>> Question Number. 11. Inlet guide vanes are anti-iced with.
Correct Answer is. Engine bleed air.
>> Question Number. 12. Intake air turbulence.
Correct Answer is. Decreases the efficiency of the compressor.
16
>> Question Number. 13. What will be the effect of operating the intake anti-icing system of a gas
turbine engine?
Correct Answer is. A decrease in power.
Explanation. Bleeding off air from the compressor must reduce power.
>> Question Number. 14. A Piton intake is divergent from front to rear because it.
Correct Answer is. Produces the maximum amount of ram compression.
>> Question Number. 15. With an electrical ice protection system, the heating elements operate.
Correct Answer is. Part continuous - part intermittent.
>> Question Number. 16. The purpose of a bell mouth compressor inlet is to.
Correct Answer is. Maximize the aerodynamic efficiency of the inlet.
>> Question Number. 17. The vortex dissipaters installed on some turbine-powered aircraft to
prevent engine FOD Utilize.
Correct Answer is. A stream of engine bleed air blown toward the ground ahead of the
engine.
>> Question Number. 18. Variable Ramp Intakes restrict airflow by.
Correct Answer is. Creating shock-waves in the intake.
>> Question Number. 19. The inlet door of a variable geometry intake at supersonic speeds will
be.
Correct Answer is. Closed.
>> Question Number. 20. When operating an engine in icing conditions, care should be taken
when the.
Correct Answer is. Temperature is below +10°Centigrade with visible moisture.
>> Question Number. 21. Anti-icing for a turboprop is achieved by.
Correct Answer is. Electric bonded heater mats.
>> Question Number. 22. A divergent intake is.
Correct Answer is. Divergent from front to rear.
>> Question Number. 23. What purpose does the nose cone serve on the (N1) fan on a high
bypass engine?
Correct Answer is. Streamlined fairing.
Explanation. The nose cone is fitted to the N1 fan disc streamlining the airflow into the fan.
>> Question Number. 24. A variable geometry intake at subsonic speeds.
Correct Answer is. Throat area is increased.
Explanation. The inlet is only reduced at Mach 1.0 or above.
>> Question Number. 25. Electrical anti-ice.
17
Correct Answer is. Heats elements, placed under mats around engine.
>> Question Number. 26. The cycling speed of the electrical de-icing mat.
Correct Answer is. Is affected by weather conditions.
>> Question Number. 27. The variable inlet guide vanes are operated.
Correct Answer is. By fuel pressure.
Explanation. IGV's have traditionally been electrically controlled and fuel operated, within an
IGV actuator.
>> Question Number. 28. The intake of a gas turbine engine is designed to.
Correct Answer is. Provide turbulent free air.
>> Question Number. 29. The velocity of air on entry to compressor inlet on an aircraft flying
supersonic speed would be
Controlled at.
Correct Answer is. Mach 0.4.
Explanation. The variable ramp causes a normal shock wave to form in the intake thus Mach
1 is the maximum speed through it; however it is further slowed by diffusion in the divergent
portion of the intake duct.
>> Question Number. 30. If an inlet is choked then the velocity.
Correct Answer is. Decreases and pressure increases.
Explanation. A choked nozzle will occur as the air reaches Mach 1; hence it is forming a
shock-wave in the intake.
>> Question Number. 31. In an aircraft flying at supersonic speed, to reduce the air velocity at the
compressor, the
Variable intake.
Correct Answer is. Throat area is decreased.
>> Question Number. 32. A well designed intake will take advantage of forward speed by.
Correct Answer is. Converting kinetic energy into pressure energy.
Explanation. This is known as Ram effect.
>> Question Number. 33. In subsonic multi-engine aircraft, a normal inlet duct will.
Correct Answer is. Increase in size, front to rear, along length of the duct.
>> Question Number. 34. What type of intake is one that decreases gradually in area and then
increases?
Correct Answer is. Convergent / Divergent.
Explanation. The fixed plug supersonic intake is a con/di shaped intake.
>> Question Number. 35. In an electrical de-icing system, the main elements will be on.
18
Correct Answer is. Continuously and intermittently.

>> Question Number. 36. Intakes are designed to.
Correct Answer is. Decelerate the free air stream flow.
>> Question Number. 37. The air intake for a gas turbine powered subsonic aircraft would be of.
Correct Answer is. Divergent form.
>> Question Number. 38. Turboprop engine inlet anti-ice system operates.
Correct Answer is. Continuously.
Explanation. Whilst the blades may be intermittent the intake mat is on continuously.
>> Question Number. 39. What is true for a bell mouth intake?
Explanation. A bell mouth intake is only used on helicopters or static test beds to improve
aerodynamic efficiency. It is a Convergent duct therefore pressure decreases and velocity
increases.
>> Question Number. 40. What is the system that breaks up ice formations on a turboprop engine
nose cowl called?
Correct Answer is. De-icing.
Explanation. Whilst the nose cowl is heated (by air or oil) the question is about removing ice
after it has formed so Deicing is correct.
>> Question Number. 41. In a variable geometry intake, the velocity of the air on the engine
compressor face is controlled by.
Correct Answer is. Shock-wave pattern, ramp and spill doors.
19
15.4 Engine Compressors.

>> Question Number. 1. A bypass engine LP compressor.
Correct Answer is. Supplies more air than is required for combustion.
Explanation. By definition the bypass duct sends air around the combustion chamber.
>> Question Number. 2. How does a dual axial flow compressor improve the efficiency of a
turbojet engine?
Correct Answer is. Higher compression ratios can be obtained.
>> Question Number. 3. In a reverse flow system, the last stage of an axial flow compressor is
often centrifugal. This is to.
Correct Answer is. Provide initial turning of the airflow.
>> Question Number. 4. What are the two main functional components in a centrifugal
compressor?
Correct Answer is. Impeller and diffuser.
>> Question Number. 5. A bypass ratio of 5:1 indicates that the bypass flow is.
Correct Answer is. Five times the hot stream.
>> Question Number. 6. The stator vanes in an axial-flow compressor.
Correct Answer is. Convert velocity energy into pressure energy.
>> Question Number. 7. What units in a gas turbine engine aid in stabilization of the compressor
during low thrust engine Operations?
Correct Answer is. Bleed air valves.
>> Question Number. 8. What purpose do the diffuser vanes of a centrifugal compressor serve?
Correct Answer is. To convert kinetic energy into pressure energy.
>> Question Number. 9. During the high RPM range on an axial flow gas turbine engine, in what
position are the variable Intake guide vanes and bleed valves?
Correct Answer is. At minimum swirl position, bleed valves closed.
>> Question Number. 10. What is the purpose of the diffuser section in a turbine engine?
Correct Answer is. To increase pressure and reduce velocity.
>> Question Number. 11. The fan speed of a twin spool axial compressor engine is the same as
the.
Correct Answer is. Low pressure compressor.
>> Question Number. 12. Bleed valves are normally spring loaded to the.
Correct Answer is. Open position.
>> Question Number. 13. What is the function of the stator vane assembly at the discharge end
of a typical axial flow?
20
Compressor?
Correct Answer is. To straighten airflow to eliminate turbulence.
>> Question Number. 14. In a turbine engine with a dual spool compressor, the low speed
compressor.
Correct Answer is. Seeks its own best operating speed.
>> Question Number. 15. What units in a gas turbine engine aid in guiding the airflow during low
thrust engine
Operations?
Correct Answer is. Inlet guide vanes.
>> Question Number. 16. What is one purpose of the stator blades in the compressor section?
Correct Answer is. Control the direction of the airflow.
>> Question Number. 17. Compressor stall is caused by.
Correct Answer is. A high angle of attack airflow through the first stages of compression.
>> Question Number. 18. What is used to aid in stabilization of compressor airflow?
Correct Answer is. Variable guide vanes and/or compressor bleed valves.
>> Question Number. 19. What is the primary factor which controls the pressure ratio of an axial
flow compressor?
Correct Answer is. Number of stages in compressor.
>> Question Number. 20. The non-rotating axial-flow compressor airfoils in an aircraft gas turbine
are known as.
Correct Answer is. Stator vanes.
>> Question Number. 21. The purpose of a bleed valve, located in the beginning stages of the
compressor is to.
Correct Answer is. Vent some of the air overboard to prevent a compressor stall.
>> Question Number. 22. During the low RPM range on an axial flow gas turbine engine, in what
position are the variable
Intake guide vanes and bleed valves?
Correct Answer is. At maximum swirl position, bleed valves open.
>> Question Number. 23. The energy changes that take place in the impeller of a centrifugal
compressor are.
Correct Answer is. Pressure increase, velocity increase, temperature increase.
>> Question Number. 24. What is the primary advantage of an axial flow compressor over a
centrifugal compressor?
Correct Answer is. Greater pressure ratio.
21
>> Question Number. 25. Compression occurs.

Correct Answer is. Across stators and rotors.
>> Question Number. 26. Which of the following can cause fan blade shingling in a turbofan
engine?
Correct Answer is. Large, rapid throttle movements and FOD.
>> Question Number. 27. Severe rubbing of turbine engine compressor blades will usually cause.
Correct Answer is. Galling.
>> Question Number. 28. Which two elements make up the axial flow compressor assembly?
Correct Answer is. Rotor and stator.
>> Question Number. 29. If the RPM of an axial flow compressor remains constant, the angle of
attack of the rotor blades
Can be changed by.
Correct Answer is. Changing the velocity of the airflow.
>> Question Number. 30. The gas turbine Compressor Pressure Ratio is.
Correct Answer is. Compressor discharge pressure divided by Compressor inlet pressure.
>> Question Number. 31. An advantage of the centrifugal flow compressor is its high.
Correct Answer is. Peak efficiency.
>> Question Number. 32. The compression ratio of an axial flow compressor is a function of the.
Correct Answer is. Number of compressor stages.
>> Question Number. 33. Jet engine turbine blades removed for detailed inspection must be
reinstalled in.
Correct Answer is. The same slot.
>> Question Number. 34. The procedure for removing the accumulation of dirt deposits on
compressor blades is called.
Correct Answer is. Field cleaning.
>> Question Number. 35. The two types of centrifugal compressor impellers are.
Correct Answer is. Single entry and double entry.
>> Question Number. 36. Between each row of rotating blades in a compressor, there is a row
of stationary blades which Act to diffuse the air. These stationary blades are called.
Correct Answer is. Stators.
>> Question Number. 37. Bleed valves are.
Correct Answer is. Closed at high RPM.
>> Question Number. 38. Compressor field cleaning on turbine engines is performed primarily in
order to.
22
Correct Answer is. Prevent engine performance degradation, increased fuel costs, and
damage or corrosion to gas path Surfaces.
>> Question Number. 39. If the LP compressor shaft severed.
Correct Answer is. The LP turbine will speed up and the LP compressor will slow down.
Explanation. The LP Turbine is attached to the LP compressor.
>> Question Number. 40. An advantage of a centrifugal compressor is.
Correct Answer is. It is robust and can stand some shock from icing-up.
>> Question Number. 41. Variable inlet guide vanes prevent.
Correct Answer is. Compressor stalling.
>> Question Number. 42. An axial flow compressor surges when.
Correct Answer is. All stages are stalled.
Explanation. The definition of a surge is when all stages are stalled and flow reversal occurs.
>> Question Number. 43. As a consequence of tapping air from the compressor, the TGT will.
Correct Answer is. Rise.
Explanation. When a bleed valve opens it is always accompanied by a rise in TGT of 15-30
degrees.
>> Question Number. 44. Compressor air bleeds promote the flow of air through the early stages
by.
Correct Answer is. Opening to allow air out.
>> Question Number. 45. .Compressor blades have a reduced angle of attack at the tips.
Correct Answer is. To allow uniform axial velocity.
>> Question Number. 46. Compressor surge is caused by.
Correct Answer is. Over fuelling.
Explanation. Fuel system malfunction - over fuelling.
>> Question Number. 47. Pressure rise across a single spool axial flow compressor is in the order
of.
Correct Answer is. Up to fifteen to one.
>> Question Number. 48. What purpose do the diffuser vanes of a centrifugal compressor serve?
Correct Answer is. To convert kinetic energy into pressure energy.
>> Question Number. 49. The purpose of the rotating guide vanes on a centrifugal compressor
is to.
Correct Answer is. Provide initial diffusing of the air.
>> Question Number. 50. What is the surge margin of an axial flow compressor?
Correct Answer is. The margin between the compressor working line and the surge line.
23
>> Question Number. 51. The compression ratio of a jet engine is.
Correct Answer is. The ratio between compressor outlet pressure and compressor inlet
pressure.
Explanation. The higher the ratio the more efficient the engine.
>> Question Number. 52. Variable inlet guide vanes help to prevent.
Correct Answer is. Compressor stalling.
>> Question Number. 53. Air through the compressor, before entering the combustion chamber,
passes.
Correct Answer is. Through divergent passage to increase the pressure.
Explanation. All compressor blades and stators are divergent, and all increase pressure.
>> Question Number. 54. Low mass airflow through a compressor will produce.
Correct Answer is. Stalling of early stages.
>> Question Number. 55. A bleed valve.
Correct Answer is. Relieves compressor choking at low RPM.
>> Question Number. 56. If a compressor has a compression ratio of 9:1 and an intake
compression of 2:1, what is the Overall compression ratio?
Correct Answer is. 18:1.
>> Question Number. 57. A compressor stage stalls when.
Correct Answer is. Smooth airflow is disrupted.
>> Question Number. 58. Inlet guide vanes are fitted to.
Correct Answer is. Control the angle of airflow into the compressor.
>> Question Number. 59. Why, in an axial flow compressor is the cross sectional area of the
compressor air duct reduced at each stage?
Correct Answer is. To maintain the velocity of the air under rising pressure.
>> Question Number. 60. An abatable lining around the fan is to.
Correct Answer is. Strengthen the EPR value.
Explanation. Prevents fan blade tip losses.
>> Question Number. 61. Allowable damage on the first stage compressor blade is restricted to.
Correct Answer is. Middle third of the blade to the outer edge.
>> Question Number. 62. Tip speed of a centrifugal compressor can reach.
>> Question Number. 63. What is the profile of a compressor blade?
Correct Answer is. A cutout that reduces blade tip thickness.
24
>> Question Number. 64. The resultant velocity of air exiting an axial compressor stage depends
upon.
Correct Answer is. Both of the above.
>> Question Number. 65. What is a compressor stage?
Correct Answer is. One rotor plus one stator.
>> Question Number. 66. If the bypass ratio is 0.7:1, the 0.7 pounds of air is.
Correct Answer is. Fed around the engine to 1 pound fed into H.P. compressor.
>> Question Number. 67. Advantage of an axial flow over a centrifugal flow gas turbine engine.
Correct Answer is. High peak efficiencies.
Explanation. Rolls Royce the Jet engine page 21 shows how higher compression ratios (axial
flow compressors) give lower SFC. Which means higher efficiency.
>> Question Number. 68. Compressor blades reduce in length.
Correct Answer is. From L.P to H.P section to maintain uniform velocity in compressor.
>> Question Number. 69. Deposit build-up on compressor blades.
Correct Answer is. Can decrease compressor efficiency and cause corrosion.
>> Question Number. 70. The diffuser after the compressor, before the combustion chamber.
Correct Answer is. Decreases velocity, pressure increases.
Explanation. Assuming this refers to a centrifugal compressor
>> Question Number. 71. In a compressor, diffusion action takes place across.
Correct Answer is. Rotors and stators.
Explanation. Stators and rotors in compressors both form divergent ducts hence they both
diffuse.
>> Question Number. 72. The ring of fixed blades at the intake of an axial flow compressor are
called.
Correct Answer is. Inlet guide vanes.
Explanation. The fixed IGV's precede the 1st stage rotor which is in front of the 1st stage
stator.
>> Question Number. 73. What is the purpose of pressure balance seal?
Correct Answer is. To ensure the location bearing is adequately loaded throughout the
engine thrust range.
Explanation. Pressure balance seals oppose the tendency of compressors to move forward.
>> Question Number. 74. The optimum air speed for entrance into the compressor is
approximately.
25
Explanation. Diffusion in the intake reduces the speed to 500ft/second (about Mach 0.4).
>> Question Number. 75. What is the acceptable damage on stator blades that have been
blended?
Correct Answer is. One third from tip to root.
Explanation. The root of the blade has tighter tolerance than the tip, and chord wise
indentations are also critical so our Best guess is from tip to root
>> Question Number. 76. With regard to compressor blades, which of the following is true? No
damage is permissible on.
Correct Answer is. A shroud fillet area.
Explanation. Shroud fillets are critical areas whereas the outer third of the blade is less so.
Unshrouded tips are also less critical than shroud fillets.
>> Question Number. 77. Identify a function of the cascade vanes in a turbojet engine compressor
section.
Correct Answer is. To remove air swirl before the combustion chamber.
Explanation. The axial flow compressor as 'containing sets of airfoils in cascade'. It further
says that the last stage of stationary vanes, called exit guide vanes turn the airflow back to an
axial direction on its way to the combustor.
>> Question Number. 78. The pressure ratio can be influenced by.
Correct Answer is. Number of stages in compressor.
Explanation. Compressors are rated by their pressure ratio, the more stages the greater the
pressure ratio.
>> Question Number. 79. Air bleed valves are.
Correct Answer is. Open at low RPM.
Explanation. Air bleed valves reduce the pressure developed in a compressor until the speed
is increased towards the Blade design speed.
>> Question Number. 80. The compressor case annulus is.
Correct Answer is. Convergent.
Explanation. All axial flow compressor case annulus are convergent to maintain a constant
axial velocity through the Compressor.
>> Question Number. 81. If the tip clearance in a centrifugal compressor is too small.
Correct Answer is. Aerodynamic buffeting would cause vibration.
Explanation. Rolls Royce the Jet Engine page 22 para 12 refers to too small a clearance
setting up aerodynamic buffet.
26
>> Question Number. 82. A 1st stage LP compressor blade is able to continue in service if the
damage is within limits, and within the.
Correct Answer is. Outer third only.
Explanation. Repairs across the chord or at the root are normally prohibited, outer third is
the only safe answer.
>> Question Number. 83. What is meant by a compressor stage?
Correct Answer is. One rotor and one stator assembly.
>> Question Number. 84. What is the normal pressure rise across each compressor stage of an
axial flow compressor?
Correct Answer is. 1.2:1.
>> Question Number. 85. Where does compression take place as air passes through an axial
flow compressor?
Correct Answer is. Rotor and Stator blades.
Explanation. Compression occurs through all stages figure 3.9 page 25 of Rolls Royce the
Jet Engine refers.
>> Question Number. 86. Nozzle Guide Vane bow is an indication of.
Correct Answer is. Engine overheat.
Explanation. Early turbines, both blades and NGV were susceptible to 'creep' -- prolonged
exposure to excessive heat.
>> Question Number. 87. A buildup of foreign objects and dirt on compressor blades.
Correct Answer is. Has a large effect on compressor efficiency and may cause corrosion.
Explanation. Compressor washes are used to reduce this problem.
>> Question Number. 88. What is the purpose of the stator vanes in the compressor section of a
gas turbine engine?
Correct Answer is. Control direction of the airflow.
>> Question Number. 89. In a twin spool compressor, the LP section runs at.
Correct Answer is. A lower RPM than the HP spool.
27
15.5 Combustion Section.

>> Question Number. 1. In a turbojet engine, combustion occurs at.
Correct Answer is. Constant pressure.
>> Question Number. 2. A tube-annular gas turbine combustion system consists of.
Correct Answer is. A number of flame tubes in an annular air casing.
>> Question Number. 3. In which type of turbine engine combustion chamber is the case and liner
removed and installed as one unit during routine maintenance?
Correct Answer is. Can.
>> Question Number. 4. In a turboprop engine, combustion takes place at constant.
Correct Answer is. Pressure.
>> Question Number. 5. The air passing through the combustion chamber is.
Correct Answer is. Used to support combustion and to cool the engine.
>> Question Number. 6. The air used for combustion is.

Correct Answer is. Primary.
Explanation. Air through the core engine is defined as primary air.
>> Question Number. 7. Combustion chamber flame temperature is in the order of.
Correct Answer is. 2000°Centigrade.
>> Question Number. 8. Hot spots in the combustion section of a turbojet engine are possible.
Correct Answer is. Malfunctioning fuel nozzles.
>> Question Number. 9. Another name for a cannula combustion chamber is.
Correct Answer is. Can-annular.
>> Question Number. 10. Another name for a cannula combustion chamber is.
Correct Answer is. Tube-annular.
>> Question Number. 11. The approximate percentage of the mass airflow taken in by the flame
tube snout is.
Correct Answer is. 18%.
>> Question Number. 12. What component creates a vortex in a gas turbine flame tube?
Correct Answer is. Swirl vanes.
>> Question Number. 13. in the combustion chamber.
Correct Answer is. Static pressure decreases slightly and volume increases.
>> Question Number. 14. Which of the following types of combustion sections are used in aircraft
turbine engines?
Correct Answer is. Multiple can, annular, and can-annular.
28
>> Question Number. 15. Secondary air in the combustion chamber is used for.
Correct Answer is. Cooling.
>> Question Number. 16. Duplex burners have.
Correct Answer is. Two calibrated outlets.
>> Question Number. 17. The overall air/fuel ratio of a combustion chamber can vary between.
Correct Answer is. 45:1 and 130:1.
>> Question Number. 18. When light-up takes place.
Correct Answer is. Interconnectors spread the heat to adjacent flame tubes.
>> Question Number. 19. Why do the holes in the body of the duple burner provide air to the
shroud around the burner Head?
Correct Answer is. To minimize carbon formation on the burner face.
>> Question Number. 20. The air passing through the combustion chamber of a jet engine is.
Correct Answer is. Used to support combustion and to cool the engine.
>> Question Number. 21. A steroidal vortex is.
Correct Answer is. A region in the combustion chamber of low velocity re-circulation.
>> Question Number. 22. Why is it necessary to have a combustion drain system?
Correct Answer is. To prevent initial over-fuelling on start up or hot start.
Explanation. Excess fuel is drained on shutdown to avoid a subsequent hot start.
>> Question Number. 23. What is a cannula combustion system?
Correct Answer is. A set of flame tubes, enclosed in a common air casing.
Explanation. Also known as tube-annular see Rolls Royce the Jet Engine page 41.
>> Question Number. 24. The flame temperature is approximately.
Correct Answer is. 2000°Centigrade.
>> Question Number. 25. Fuel entering the combustion chamber from an atomizer spray nozzle
enters as.
Correct Answer is. A fuel/air mixture.
>> Question Number. 26. An advantage of an annular combustion system is.
Correct Answer is. Decrease in combustor length compared to a tube-annular combustor of
the same output.
>> Question Number. 27. How is the combustion chamber drain valve closed?
Correct Answer is. By combustion chamber gas pressure.
>> Question Number. 28. Which statement is true regarding the air passing through the
combustion section of a jet Engine?
Correct Answer is. Most is used for engine cooling.
29
>> Question Number. 29. How are combustion liner walls cooled in a gas turbine engine?
Correct Answer is. By secondary air flowing through the combustion chamber.
>> Question Number. 30. Dilution air is placed.
Correct Answer is. In the dilution zone of the combustion chamber after the primary zone.
Explanation. The air cools and adds to the mass flow.
>> Question Number. 31. A Duplex burner uses.
Correct Answer is. Small burner at low RPM and both burner at hi RPM.
>> Question Number. 32. The approximate percentage of the mass airflow which bypasses the
flame tube snout is.
Explanation. Rolls Royce the Jet Engine page 36 shows 20%.
>> Question Number. 33. Flame stabilization in a combustion chamber is achieved by.
Correct Answer is. The airflow pattern.
>> Question Number. 34. Fuel nozzles are cleaned.
Correct Answer is. In-situ with detergent solution.
>> Question Number. 35. When heat is added to the combustion chamber.
Correct Answer is. Pressure changes slightly and volume.
>> Question Number. 36. A shroud placed around fuel nozzles.
Correct Answer is. Prevents carbon build up.
>> Question Number. 37. Carbon forming on fuel spray nozzles will have the effect of.
Correct Answer is. Changing the fuel spray angle.
Explanation. Carbon on the fuel nozzles will distort fuel spray flow and direction. This can
cause hot spots within the Combustion chamber.
>> Question Number. 38. Combustor air that is not used to support combustion.
Correct Answer is. Will film cool the liner and dilute combustion chamber exit temperature.
Explanation. This air is known as secondary or tertiary combustor air.
>> Question Number. 39. At high rotational speed at sea level, a duple burner would be passing
fuel via the.
Correct Answer is. Primary and the main nozzle.
Explanation. The duple nozzle is also called the duplex nozzle. RR the Jet Engine page 116
refers.
>> Question Number. 40. The fabricated liner of a flame tube is achieved mainly by.
Correct Answer is. Argon arc process.
30
Explanation. An argon arc (T.I.G) welding is used to repair combustion liners, it is assumed
that this is also the Manufacturing process. Can anyone confirm this with a reference?
>> Question Number. 41. Why is it necessary to have a combustion chamber drain?
Correct Answer is. To allow unburnt fuel to drain away.
Explanation. The residual fuel must be drained off to prevent subsequent wet starts.
>> Question Number. 42. The purpose of the swirl vanes in the combustion chamber is to
produce.
Correct Answer is. Gas re-circulation.
Explanation. Rolls Royce the Jet Engine page 36 paragraph 7 refers to recirculating gases.
>> Question Number. 43. A vaporizing burner injects fuel vapor.
Correct Answer is. Against the airflow.
>> Question Number. 44. A duplex burner in a gas turbine engine has 2 orifices.
Correct Answer is. One for low speed conditions the second used for high speed conditions.
Explanation. This is a most right answer. Primary flow only normally occurs only during start
(low flow)
>> Question Number. 45. A combustion chamber has a.
Correct Answer is. Divergent inlet, convergent outlet.
31
15.6 Turbine Section.

>> Question Number. 1. The three main types of turbine blades are.
Correct Answer is. Impulse, reaction, and impulse-reaction.
>> Question Number. 2. What are the two main basic components of the turbine section in a gas
turbine engine?
Correct Answer is. Stator and rotor.
>> Question Number. 3. Turbine impulse blading forms a.
Correct Answer is. Constant area duct.
>> Question Number. 4. The turbine section.
Correct Answer is. Drives the compressor section.
>> Question Number. 5. Where do stress rupture cracks usually appear on turbine blades?
Correct Answer is. Across the leading or trailing edge at a right angle to the edge.
>> Question Number. 6. What is meant by a shrouded turbine?
Correct Answer is. The turbine blades are shaped so that their ends form a band or shroud.
>> Question Number. 7. Turbine nozzle diaphragms located on the upstream side of each turbine
wheel, are used to.
Correct Answer is. Direct the flow of gases parallel to the vertical line of the turbine blades.
>> Question Number. 8. Reduced blade vibration and improved airflow characteristics in turbines
are brought by.
Correct Answer is. Shrouded turbine rotor blades.
>> Question Number. 9. What term is used to describe a permanent and cumulative deformation
of turbine blades?
Correct Answer is. Creep.
>> Question Number. 10. What is the major function of the turbine assembly in a turbojet engine?
Correct Answer is. Supplies the power to turn the compressor.
>> Question Number. 11. Gas pressure through the turbine section will generally.
>> Question Number. 12. A condition known as 'hot streaking' in turbine engines is caused by
Correct Answer is. A partially clogged fuel nozzle.
>> Question Number. 13. Temperature through the turbine stages generally.
Correct Answer is. Decreases.
>> Question Number. 14. Shrouded blades allow.
Correct Answer is. Thinner more efficient blade sections to be used.
32
>> Question Number. 15. Continued and/or excessive heat and centrifugal force on turbine engine
rotor blades is likely to cause.
Correct Answer is. Creep.
>> Question Number. 16. N.G.V's form.
Correct Answer is. Convergent ducts.
>> Question Number. 17. Dirt particles in the air going into the compressor of a turbine engine
will form a coating on all but which of the following?
Correct Answer is. Turbine blades.
>> Question Number. 18. Reduced blade vibration and improved airflow characteristics in gas
turbines are brought about by.
Correct Answer is. Shrouded turbine rotor blades.
>> Question Number. 19. A purpose of the shrouds on the turbine blades of an axial flow engine
is to.
Correct Answer is. Reduce vibration.
>> Question Number. 20. Hot section inspections for many modern turbine engines are required.
Correct Answer is. On a time or cycle basis.
>> Question Number. 21. Why do some turbine engines have more than one turbine wheel
attached to a single shaft?
Correct Answer is. To extract more power from the exhaust gases than a single wheel can
absorb.
>> Question Number. 22. When aircraft turbine blades are subjected to excessive heat stress,
what type of failures would? You expect?
Correct Answer is. Stress rupture.
>> Question Number. 23. Which of the following conditions is usually not acceptable to any extent
in turbine blades?
Correct Answer is. Cracks.
>> Question Number. 24. The forces driving a turbine round are due to.
Correct Answer is. Impulse and reaction.
>> Question Number. 25. Nozzle guide vanes give a.
Correct Answer is. Pressure decrease, velocity increase.
>> Question Number. 26. Shrouding of stator blade tips is to.
Correct Answer is. Minimize vibration.
>> Question Number. 27. Why are two or more turbine wheels coupled?
Correct Answer is. So power output is doubled.
33
>> Question Number. 28. Running clearance on a turbine disk is kept to a minimum to reduce.
Correct Answer is. Tip losses.
>> Question Number. 29. Two basic types of turbine blades are.
Correct Answer is. Reaction and impulse.
>> Question Number. 30. Why are nozzle guide vanes fitted?
Correct Answer is. To increase velocity of the gas flow.
>> Question Number. 31. A turbine disk is.
Correct Answer is. A disk at the core of the engine that the blades are attached to.
Explanation. The turbine blades are mounted to the disc which absorbs the centrifugal force.
>> Question Number. 32. .When carrying out a borescope the damage on turbine blades that
would indicate a failure is.
Correct Answer is. Tip curl.
>> Question Number. 33. The active clearance control system aids turbine engine efficiency by.
Correct Answer is. Ensuring turbine blade to engine case clearances are kept to a minimum
by controlling case temperatures.
>> Question Number. 34. Turbine rear struts.
Correct Answer is. Straighten the gas flow.
>> Question Number. 35. Bowing of turbine blades indicates an.
Correct Answer is. Over-temperature condition.
Explanation. Bowing as part of the ageing process. Over temp is the only answer relevant to
aging (temperature creep).
>> Question Number. 36. On an impulse-reaction turbine blade it is.
Correct Answer is. Impulse at the root and reaction at the tip.
>> Question Number. 37. Turbine creep effects.
Correct Answer is. Turbine blades.
>> Question Number. 38. Creep is.
Correct Answer is. A permanent deformation of turbine.
>> Question Number. 39. Creep, overall.
Correct Answer is. Increases turbine diameter.
>> Question Number. 40. How are turbine disks attached to the shaft in gas turbine engine?
Correct Answer is. Bolted.
>> Question Number. 41. Fir tree turbine blade attachment locates the blade.
Correct Answer is. Allows slight movement.
>> Question Number. 42. Creep may occur to turbine blades due to.
34
Correct Answer is. Over-temp with excessive centrifugal loads.

38 of 111 03-May-18, 4:52 PM
Explanation. Creep is irreversible Rolls Royce the Jet Engine Page 56 refers.
>> Question Number. 43. Creep may occur to turbine blades due to.
Correct Answer is. Over-temp with excessive centrifugal loads.
Explanation. Creep is irreversible Rolls Royce the Jet Engine Page 56 refers.
>> Question Number. 44. Forces driving the turbine are due to.
Correct Answer is. Momentum and directional acceleration of gases.
>> Question Number. 45. Impulse turbine blades run cooler than reaction blades because.
Correct Answer is. Temperature drop across N.G.V is greater.
Explanation. Impulse blades have total pressure drop in N.G.V's hence air is colder as it
enters turbine RR Page51 refers.
>> Question Number. 46. An increase in turbine diameter is caused by.
Correct Answer is. Prolonged high temperatures and centrifugal loads.
Explanation. This is known as creep.
>> Question Number. 47. Which of the following is most likely to occur in the turbine section of a
gas turbine engine?
Correct Answer is. Cracking.
Explanation. A turbine bearing is under great heat stress, cracking is the only possible choice
here.
>> Question Number. 48. Aluminum deposits on the turbine show up as.
Correct Answer is. White or silver speckles.
Explanation. CAIPs E L/3-10 refers. It also says titanium speckles are blue or gold.
>> Question Number. 49. An impulse/reaction turbine is designed to ensure.
Correct Answer is. Uniform axial velocity from blade root to tip.
>> Question Number. 50. Excessive turbine temperatures can lead to.
Correct Answer is. Turbine blade creep and an increase in the diameter of the turbine.
>> Question Number. 51. What are blue and golden deposits evidence of, on a turbine
blade?
Correct Answer is. Titanium.
Explanation. Aluminium and magnesium leave white powder deposits so by elimination the
answer is titanium.
>> Question Number. 52. Necking and mottling of turbine blades.
Correct Answer is. Is due to thermal stress.
35
Explanation. Necking could occur due to creep which is a function of thermal stress and
centrifugal loads, and turbine blades do show signs of discoloration after use, the latter is not
normally a defect.
>> Question Number. 53. Impulse blades operate cooler than reaction blades because.
Correct Answer is. The airflow has a higher velocity through a impulse turbine N.G.V.
Explanation. Impulse turbine N.G.Vs accelerate gases faster than their reaction counterparts
therefore the pressure and temperature is reduced more in the impulse turbine.
>> Question Number. 54. During a borescope check of the H.P turbine blades.
Correct Answer is. Attach a device to the accessory gearbox and rotate slowly.
Explanation. All large GTE have a hand turning tool adaptor fitted to the accessory or high
speed gearbox.
>> Question Number. 55. The turbine section of a jet engine.
Correct Answer is. Converts dynamic pressure into mechanical energy.
Explanation. The shape and size of the turbine blades determines the amount of energy
extracted from the dynamic pressure of the airflow.
>> Question Number. 56. The temperature and centrifugal loads which the turbine is subjected to
during normal engine Operation causes.
Correct Answer is. Creep loading.
Explanation. Creep is a permanent deformation caused by high centrifugal loads at
continuous high temperature.
>> Question Number. 57. Impulse-reaction turbine blades form.
Correct Answer is. Tip half reaction, root half Impulse.
Explanation. Turbine blades move from impulse at the root to reaction at the tip.
>> Question Number. 58. A fir tree root.
Correct Answer is. Attaches turbine blades to the turbine disk.
Explanation. Rolls Royce the Jet Engine Page 52 para 19 refers.
>> Question Number. 59. The passage between adjacent nozzle guide vanes forms a.
Correct Answer is. Convergent duct.
>> Question Number. 60. as the hot gasses flow through an impulse turbine blading, the velocity.
. Correct Answer is. Remains constant.
Explanation. In an 'Impulse bladed turbine' the turbine blades form parallel ducts therefore
the velocity will remain constant figure 5-5 of RR the Jet Engine shows the contour of impulse
turbine blades.
>> Question Number. 61. What is the normal range of turbine efficiency?
36
Correct Answer is. 90% - 95%.

Explanation. Rolls Royce the Jet Engine page 51 Para 11 refers to 92%.
>> Question Number. 62. Turbine engine components are never manufactured by.
Correct Answer is. Gas welding.
Explanation. Both Argon arc and Electron beam welding are referred to in RR the Jet Engine
so we assume gas welding is not used, this is probably due to carburization of the weld.
>> Question Number. 63. How is a radial turbine driven?
Correct Answer is. By change of momentum and angle of airflow.
Explanation. Radial turbines are effectively reversed centrifugal compressors.
>> Question Number. 64. Turbine disk growth is due to.
Correct Answer is. A permanent change in disk diameter.
Explanation. The turbine disc does not include the blades.
>> Question Number. 65. A nozzle guide vane is.
Correct Answer is. Hollow in construction to allow for flow of cooling air.
Explanation. Air is tapped from the H.P compressor and passed through the N.G.V to cool
it.
>> Question Number. 66. A slow constant growth in a turbine blade is known as.
Correct Answer is. Secondary creep.
37
15.7 Engine Exhaust.

>> Question Number. 1. The function of the exhaust cone assembly of a turbine engine is to.
Correct Answer is. Straighten and collect the exhaust gases into a solid exhaust jet.
>> Question Number. 2. A nozzle is 'choked' when the gas flow or air flow at the throat is.
Correct Answer is. Sonic.
>> Question Number. 3. The struts on the exhaust cone.
Correct Answer is. Support the exhaust cone and straighten the gas flow.
>> Question Number. 4. A nozzle is 'choked' when the engine inlet airflow is.
Correct Answer is. Subsonic or supersonic.
>> Question Number. 5. What is the maximum practical angle through which the gas flow can be
turned during thrust reversal?
Correct Answer is. 135°.
>> Question Number. 6. A supersonic duct is.
Correct Answer is. Convergent then divergent along its length.
Explanation. Visualize the exhaust nozzle of the space shuttle booster rockets.
>> Question Number. 7. Noise from the jet wake when untreated by suppression is.
Correct Answer is. Low frequency, high decibel.
>> Question Number. 8. Hot spots on the tail cone of a turbine engine are possible indicators of
a malfunctioning fuel nozzle or.
Correct Answer is. A faulty combustion chamber.
>> Question Number. 9. An exhaust cone placed aft of the turbine in a jet engine will cause the
pressure in the first part of the exhaust duct to.
Correct Answer is. Increase and the velocity to decrease.
>> Question Number. 10. A convergent-divergent nozzle.
Correct Answer is. Makes maximum use of pressure thrust.
>> Question Number. 11. The velocity of supersonic air as it flows through a divergent nozzle.
>> Question Number. 12. The Jet Pipe of a gas turbine engine.
Correct Answer is. Protects the airframe from heat damage.
>> Question Number. 13. For what purpose is the propelling nozzle of a gas turbine engine
designed?
Correct Answer is. To increase the velocity and decrease the pressure of the gas stream
leaving the nozzle.
>> Question Number. 14. If the exit area of the nozzle was too large, the effect is.
38
Correct Answer is. Exit velocity lower causing loss of thrust.

>> Question Number. 15. A choked nozzle.
Correct Answer is. Increases thrust.
>> Question Number. 16. The exhaust section is designed to.
Correct Answer is. Impart a high exit velocity to the exhaust gases.
>> Question Number. 17. Reverse thrust can only be selected when the throttle is.
>> Question Number. 18. A Convergent-Divergent nozzle.
Correct Answer is. Makes maximum use of Pressure thrust.
>> Question Number. 19. On front fan engines, to obtain thrust reversal, the.
Correct Answer is. Cold stream is reversed.
>> Question Number. 20. Exhaust noise can be reduced by.
Correct Answer is. Increasing the mixing rate.
>> Question Number. 21. Operating thrust reversers at low ground speeds can sometimes cause.
Correct Answer is. Sand or other foreign object ingestion, hot gas re-ingestion, compressor
stalls.
>> Question Number. 22. Thrust reversers utilizing a pneumatic actuating system, usually receive
operating pressure from.
Correct Answer is. Sand or other foreign object ingestion, hot gas re-ingestion, compressor
stalls.
>> Question Number. 23. The purpose of cascade vanes in a thrust reversing system is to:
Correct Answer is. Turn to a forward direction the fan and/or hot exhaust gases that have been
blocked from exiting through the exhaust nozzle.
>> Question Number. 24. A convergent exhaust nozzle produces mainly.
Correct Answer is. Momentum thrust.
>> Question Number. 25. The rearward thrust capability of an engine with the thrust reverser
system deployed is.
Correct Answer is. Less than its forward capability.
>> Question Number. 26. Which statement is generally true regarding thrust reverser systems?
.simultaneously).
Correct Answer is. It is possible to move some aircraft backward on the ground using
reverse thrust.
>> Question Number. 27. What is the proper operating sequence when using thrust reversers to
slow an aircraft after landing?
39
Correct Answer is. Retard thrust levers to ground idle, raise thrust reverser levers as
required, and retard thrust reverser levers to ground idle.
>> Question Number. 28. Most exhaust system failures result from thermal fatigue cracking in the
areas of stress concentration. This condition is usually caused by.
Correct Answer is. The high temperatures at which the exhaust system operates.
>> Question Number. 29. Thrust reversal on a high bypass engine is achieved by.
Correct Answer is. Blocker doors.
>> Question Number. 30. If damage is found to the reverse thrust cascade vanes and they need
replacing, you can.
Correct Answer is. Only replace vanes with new ones that have the correct part as the
originals removed.
Explanation. Cascade vane segments are NOT interchangeable, they all direct air at different
angles.
>> Question Number. 31. When should thrust reversers be used?
Correct Answer is. At low RPM and low forward speed.
Explanation. Thrust reversers cannot be actuated if the throttles are set above idle and they
can only be used on the ground.
>> Question Number. 32. If the area of the nozzle was too large the effect is.
Correct Answer is. Exit velocity lower causing loss of the thrust.
>> Question Number. 33. Lobe type exhaust noise suppressors are made from.
Correct Answer is. Heat resistant alloy.
>> Question Number. 34. What indication does the pilot receive that thrust reversers have
deployed?
Correct Answer is. A sequence of lights.
Explanation. Boeing 757/767 use the word 'rev' in amber for unlocked and green for
deployed on the upper EICAS screen.
>> Question Number. 35. What angle are the exhaust gasses turned through in a clamshell type
thrust reverser?
Correct Answer is. 135 degrees.
Explanation. Turned through 135 degrees is 45 degrees forward, the maximum a thrust
reverser of any sort turns the air forward.
>> Question Number. 36. The purpose of a propelling nozzle is to.
Correct Answer is. Increase the velocity of the air and increase thrust.
40
Explanation. The convergence of the propelling nozzle in a subsonic pure jet engine is set
so that max speed is just below Mach 1.
>> Question Number. 37. If a thrust reverser is deployed at lower than normal landing speed.
Correct Answer is. exhaust gases can be ingested into the engine.
Explanation. Exhaust gas ingestion is a problem for thrust reverser systems when stationary
or very slow.
>> Question Number. 38. The size of the exhaust section is dictated by.
Correct Answer is. size and location of the engine.
Explanation. The exhaust section is of a certain diameter and can be of different lengths
depending on the location of the engine within the fuselage or wing root (IE English Electric
Lightning).
>> Question Number. 39. On a Clamshell door type thrust reverser. The Clamshell doors redirect
the exhaust gas stream.
Correct Answer is. 45 degrees to the thrust line.
Explanation. 45 degrees to the thrust line is an alternative to 'turned through 135 degrees'.
>> Question Number. 40. Normal gas turbine engine's exhaust duct is.
Correct Answer is. Convergent.
Explanation. The exhaust nozzle consists of a parallel duct then the propelling nozzle which
is always convergent.
>> Question Number. 41. As the air flows out at the outflow of a choked nozzle.
Correct Answer is. Velocity decreases and pressure increases.
Explanation. A choked nozzle has a shock wave in it and air is at Mach 1. After the shock
the air must be decreased in speed and pressure is rising.
41
15.8 Bearings and Seals.

>> Question Number. 1. Main bearing oil seals used with turbine engines are usually what
type(s)?
Correct Answer is. Labyrinth and/or carbon rubbing.
>> Question Number. 2. If, during inspection at engine overhaul, ball or roller bearings are
found to have magnetism but otherwise have no defects, they.
Correct Answer is. Must be degaussed before use.
>> Question Number. 3. A carbon seal has which type of sealing arrangement?
Correct Answer is. Full contact with race.
>> Question Number. 4. The highest turbine bearing temperature takes place.
Correct Answer is. At shut-down.
Explanation. On shut down the bearing loses its cooling so for short periods it may actually
heat up
>> Question Number. 5. Indentations on bearing races caused by high static loads are known as.
Correct Answer is. Brinelling.
>> Question Number. 6. The function of a labyrinth seal is to create.
Correct Answer is. A restricted leakage of air between fixed and rotating components.
>> Question Number. 7. The bearings of a compressor rotor are usually.
Correct Answer is. Ball and roller.
>> Question Number. 8. Bearing seal failure would most probably cause.
Correct Answer is. High oil consumption.
>> Question Number. 9. Why are oil seals pressurized?
Correct Answer is. To ensure minimum oil loss.
Explanation. Pressurized labyrinth seals stop oil leaking out of the bearing housing between
rotating shafts and stationary casing. Note that oil is always scavenged out of theses housings.
>> Question Number. 10. What bearing is used to take axial loads on a main rotation shaft of a
gas turbine engine?
Correct Answer is. Ball bearing.
Explanation. Ball bearings absorb force in all directions.
>> Question Number. 11. Seals on a gas turbine engine restrict leakage of oil by.
Correct Answer is. Air pressure.
>> Question Number. 12. An abradable lining in the fan case.
Correct Answer is. Provides acoustic medium.
42
Explanation. The prime purpose is to optimize fan performance, but it is also an acoustic
lining.
>> Question Number. 13. Squeeze film bearings are usually found on.
Correct Answer is. LP compressor section.
Explanation. Squeeze film bearings utilize the oil film to dampen radial out of balance. The
largest rotor is normally going to have the largest out of balance. Hence L.P compressor section
is our best guess.
>> Question Number. 14. Taper roller bearings accept loads in which direction?
Correct Answer is. Radial and axial in one direction only.
Explanation. Taper rollers are only used when the axial load is low. I.E thrust bearings are
not taper rollers, but ball bearings.
>> Question Number. 15. Some labyrinth seals.
Correct Answer is. Control the outflow of air at the turbine.
Explanation. Labyrinth seals can be air seals as well as oil seals.
>> Question Number. 16. The purpose of 'squeeze film' type bearing is to.
Correct Answer is. Minimize the effect of vibration.
Explanation. The film of oil acts as a buffer between the outer race and the casing.
>> Question Number. 17. In a jet engine the rotating assembly oil seals are maintained oil tight
by means of.
Correct Answer is. Air pressure.
Explanation. Air pressure acts across a labyrinth seal to hold the oil in the bearing chamber.
43
15.9 Lubricants and Fuels.

>> Question Number. 1. Kerosene will burn effectively at an air/fuel ratio of.
>> Question Number. 2. When using Prist or Biopor.
Correct Answer is. It is left and burnt with the fuel.
>> Question Number. 3. What is D.E.R.D 2494?
Correct Answer is. Kerosene.
>> Question Number. 4. A high viscosity index means the oil viscosity.
Correct Answer is. Will not vary greatly with temperature change.
>> Question Number. 5. A fuel system icing inhibitor is a fuel additive which.
Correct Answer is. Prevents the water in the fuel freezing.
>> Question Number. 6. What will be the result of operating an engine in extremely high
temperatures using a lubricant recommended by the manufacturer for a much lower temperature?
Correct Answer is. The oil pressure will be lower than normal.
>> Question Number. 7. The time in seconds required for exactly 60 cubic centimeters of oil to
flow through an accurately calibrated orifice at a specific temperature is recorded as a
measurement of the oil's.
Correct Answer is. Viscosity.
>> Question Number. 8. Upon what quality or characteristic of a lubricating oil is its viscosity
index based?
Correct Answer is. Its rate of change in viscosity with temperature change.
>> Question Number. 9. Compared to reciprocating engine oils, the types of oils used in turbine
engines.
Correct Answer is. Have less tendency to produce lacquer or coke.
>> Question Number. 10. If all other requirements can be met, what type of oil should be used to
achieve theoretically perfect engine lubrication?
Correct Answer is. The thinnest oil that will stay in place and maintain a reasonable film
strength.
>> Question Number. 11. In addition to lubricating (reducing friction between moving parts),
engine oil performs what functions?
Correct Answer is. Cools, seals, prevents corrosion, cushions shock loads.
>> Question Number. 12. The viscosity of a liquid is a measure of its.
Correct Answer is. Resistance to flow.
44
>> Question Number. 13. Which of the following factors helps determine the proper grade of oil
to use in a particular engine?
Correct Answer is. Operating speeds of bearings.
>> Question Number. 14. Specific gravity is a comparison of the weight of a substance to the
weight of an equal volume of.
Correct Answer is. Distilled water at a specific temperature.
>> Question Number. 15. What advantage do mineral base lubricants have over vegetable oil
base lubricants when used in aircraft engines?
Correct Answer is. Chemical stability.
>> Question Number. 16. High tooth pressures and high rubbing velocities, such as occur with
spur type gears, require the use of.
Correct Answer is. An E.P lubricant.
>> Question Number. 17. Which of these characteristics is desirable in turbine engine oil?
Correct Answer is. High flash point.
>> Question Number. 18. What action is taken to protect integral fuel tanks from corrosion due to
micro biological contamination?
Correct Answer is. A biocidal additive is added to the fuel.
>> Question Number. 19. What should be checked/changed to ensure the validity of a turbine
engine performance check if an alternate fuel is to be used?
Correct Answer is. Fuel specific gravity setting.
>> Question Number. 20. Kerosene is used as turbine engine fuel because.
Correct Answer is. Kerosene has more heat energy per gallon and lubricates fuel system
components.
>> Question Number. 21. Calorific value is the.
Correct Answer is. Amount of heat or energy in one pound of fuel.
Explanation. Measured in M.J/Kg or BTU/Lb.
>> Question Number. 22. The specific gravity of fuel affects.
Correct Answer is. Aircraft range.
Explanation. Greater Density for a fixed volume equals greater weight of fuel - hence greater
range.
>> Question Number. 23. Oil used in a gas turbine engine is usually.
Correct Answer is. Synthetic.
>> Question Number. 24. An oil spectroscope measures.
Correct Answer is. Contaminants suspended in the oil.
45
>> Question Number. 25. Ignition of fuel depends upon.

Correct Answer is. Both volatility and atomization.
Explanation. A volatile fuel will vaporize more easily. if it is a low volatility fuel (Jet-A1
etc.)then the fuel is atomized through spray nozzles into the combustion chamber.
>> Question Number. 26. Kerosene is used instead of gasoline because.
Correct Answer is. Kerosene is less volatile and has good lubrication properties.
Explanation. Kerosene is a more stable fuel for storage and handling.
>> Question Number. 27. If the specific gravity of a fuel is increased, the weight of a tank of fuel
will.
Explanation. SG = Weight of fuel relative to water.
>> Question Number. 28. Reid vapour pressure, is the vapour pressure exerted by a fuel when
heated to.
Correct Answer is. 38°C.
46
15.10 Lubrication Systems.

>> Question Number. 1. The oil pressure in the cooler is.
Correct Answer is. Higher than the fuel pressure.
>> Question Number. 2. When rotating, the gear type oil pump.
Correct Answer is. Draws oil into the pump and carries it round between the gear teeth and
casing.
>> Question Number. 3. A scavenge filter is incorporated in a gas turbine lubrication system to.
Correct Answer is. Protect the pressure pump.
>> Question Number. 4. The working fluid of a constant speed drive (C.S.D) is.
Correct Answer is. Within the unit.
Explanation. C.S.Ds and I.D.Gs have their own self-contained oil system.
>> Question Number. 5. What is the possible cause when a turbine engine indicates no change
in power setting parameters, but oil temperature is high?
Correct Answer is. Engine main bearing distress.
>> Question Number. 6. How is engine oil usually cooled?
Correct Answer is. By a fuel/oil cooler.
>> Question Number. 7. What filters are used to protect oil pressure spray jets?
Correct Answer is. In-line thread filters.
Explanation. RR book page 82 states that thread type filters are used as last chance filters.
>> Question Number. 8. The chip detector in the oil system is a.
Correct Answer is. Magnetic plug in the return line.
>> Question Number. 9. When rotating, the gyroter type oil pump.
Correct Answer is. Draws oil into the pump and carries it round between the gear teeth and
casing.
>> Question Number. 10. Oil picks up the most heat from which of the following turbine engine
components?
Correct Answer is. Turbine bearing.
>> Question Number. 11. In a jet engine which uses a fuel oil heat exchanger, the oil temperature
is controlled by a thermostatic valve that regulates the flow of.
Correct Answer is. Oil through the heat exchanger.
>> Question Number. 12. What is the purpose of the last chance oil filters?
Correct Answer is. To prevent damage to the oil spray nozzle.
>> Question Number. 13. Which of the following is a function of the fuel oil heat exchanger on a
turbojet engine?
47
Correct Answer is. Increases fuel temperature.

>> Question Number. 14. At cruise RPM, some oil will flow through the relief valve of a gear type
engine oil pump. This is normal as the relief valve is set at a pressure which is.
Correct Answer is. Lower than the pressure pump capabilities.
>> Question Number. 15. What will happen to the return oil if the oil line between the scavenger
pump and the oil cooler separates?
Correct Answer is. The scavenger return line check valve will close and force the oil to
bypass directly to the intake side of the pressure pump.
>> Question Number. 16. The oil dampened main bearing utilized in some turbine engines is
used to.
Correct Answer is. Provide an oil film between the outer race and the bearing housing in
order to reduce vibration tendencies in the rotor system, and to allow for slight misalignment.
>> Question Number. 17. After making a welded repair to a pressurized type turbine engine oil
tank, the tank should be pressure checked to.
Correct Answer is. Not less than 5 PSI plus the maximum operating pressure of the tank.
>> Question Number. 18. Possible failure related ferrous metal particles in turbine engine oil
cause an (electrical) indicating type magnetic chip detector to indicate their presence by.
Correct Answer is. Bridging the gap between the detector center (positive) electrode and
the ground electrode.
>> Question Number. 19. What would be the probable result if the oil system pressure relief valve
should stick in the open position on a turbine engine?
Correct Answer is. Decreased oil temperature.
>> Question Number. 20. What is the primary purpose of the oil to fuel heat exchanger?
Correct Answer is. Cool the oil.
>> Question Number. 21. Low oil pressure can be detrimental to the internal engine components.
However, high oil pressure.
Correct Answer is. Should be limited to the engine manufacturer's recommendations.
>> Question Number. 22. What is the primary purpose of the oil breather pressurization system
that is used on turbine engines?
Correct Answer is. Prevents foaming of the oil.
>> Question Number. 23. What type of oil system is usually found on turbine engines?
Correct Answer is. Dry sump, pressure, and spray.
>> Question Number. 24. How are the teeth of the gears in the accessory section of an engine
normally lubricated?
48
Correct Answer is. By splashed or sprayed oil.

>> Question Number. 25. Manufacturers normally require turbine engine oil servicing within a
short time after engine shutdown primarily to.
Correct Answer is. Prevent over servicing.
>> Question Number. 26. In order to relieve excessive pump pressure in an engine's internal oil
system, most engines are equipped with a.
Correct Answer is. Relief valve.
>> Question Number. 27. The type of oil pumps most commonly used on turbine engines are
classified as.
Correct Answer is. Positive displacement.
>> Question Number. 28. If the oil in the oil cooler core and annular jacket becomes congealed,
what unit prevents damage to the cooler?
Correct Answer is. Oil pressure relief valve.
>> Question Number. 29. What will result if an oil filter becomes completely blocked?
Correct Answer is. Oil will flow at the normal rate through the system.
>> Question Number. 30. A turbine engine dry sump lubrication system of the self-contained,
high pressure design.
Correct Answer is. Consists of pressure, breather, and scavenge subsystems.
>> Question Number. 31. What is the primary purpose of the hopper located in the oil supply
tank of some dry sump engine installations?
Correct Answer is. To reduce the time required to warm the oil to operating temperatures.
>> Question Number. 32. What determines the minimum particle size which will be excluded or
filtered by a cuno type (stacked disc, edge filtration) filter?
Correct Answer is. The spacer thickness.
>> Question Number. 33. A full flow oil system has.
Correct Answer is. A variable oil pressure dependent upon throttle setting.
Explanation. This system does not have a pressure regulating valve, only a max pressure
relief valve for safety purposes.
>> Question Number. 34. A felt filter in an oil lubrication system should be.
Correct Answer is. Removed and replaced with a new filter element.
>> Question Number. 35. What filter is used in a oil scavenge pump in the inlet side of the pump?
Correct Answer is. Wire mesh filter.
Explanation. Rolls Royce The Jet engine page 82 refers to a coarse strainer fatted to the
inlet of oil pumps. Wire mesh is considered to be the same thing.
49
>> Question Number. 36. A vane type oil pump output is controlled by.
Correct Answer is. Outlet pressure against spring pressure.
>> Question Number. 37. The sump in a dry sump oil system.
Correct Answer is. Is used as a collecting point only.
Explanation. Dry sumps are scavenged back to the reservoir.
>> Question Number. 38. A jet engine gear box breather is prevented from leaking oil to
atmosphere by the action of.
Correct Answer is. Impeller and centrifugal force.
Explanation. Refer to page 81 Rolls Royce the Jet Engine for a diagram of a gearbox
centrifugal breather.
>> Question Number. 39. The air-cooled-oil-cooler has an anti-surge valve in order to.
Correct Answer is. Protect the cooler.
Explanation. The term anti surge valve is unusual, an oil pressure relief bypass valve is a
better description.
>> Question Number. 40. A thread type oil seal in a lubrication system.
Correct Answer is. Has a thread on a stationary portion to prevent fluid leaks.
Explanation. This is a type of labyrinth seal, see page 92 of The Jet Engine.
>> Question Number. 41. The oil system generally used on most modern turboprop engines is.
Correct Answer is. Dry sump type.
Explanation. The oil is contained in a separate oil tank.
>> Question Number. 42. A spur gear pump operating in a lubrication system promotes.
Correct Answer is. Low flow at high pressure.
>> Question Number. 43. Last chance' filters in a lubrication system are serviced during.
Correct Answer is. Engine overhaul.
>> Question Number. 44. The identification of a lubrication fluid line is the word 'lubrication'.
Correct Answer is. Followed by squares.
50
15.11 Fuel Systems.

>> Question Number. 1. If the swash plate of a positive displacement swash plate pump is
perpendicular to the axis of the pump, the flow will be.
Correct Answer is. Zero.
>> Question Number. 2. What moves the swash plate away from the minimum stroke position?
Correct Answer is. A spring.
>> Question Number. 3. The burner fuel flow is at maximum at.
Correct Answer is. I.S.A. sea level.
>> Question Number. 4. How is servo pressure, which is used to control fuel pump 'Swash Plate'
angle obtained?
Correct Answer is. From pump delivery pressure through variable restrictions.
>> Question Number. 5. What would be the effect on the engine if the B.P.C half ball valve in the
servo line sticks open?
Correct Answer is. An increase of fuel flow, therefore an increase in RPM.
>> Question Number. 6. Why is an A.C.U fitted to a gas turbine engine?
Correct Answer is. It limits the rate of increase in fuel flow during sudden acceleration.
>> Question Number. 7. If fuel pump servo pressure is reduced, pump output will.
>> Question Number. 8. Why is the B.P.C fitted in a gas turbine engine fuel system?
Correct Answer is. To vary pressure pump output in relation to the pressure variation at the
intake.
>> Question Number. 9. What must be done after the fuel control unit has been replaced on an
aircraft gas turbine engine?
Correct Answer is. You must retrim the engine.
>> Question Number. 10. A kinetic valve is a device used to control H.P pump output. This is
achieved by movement of a.
Correct Answer is. Knife blade.
>> Question Number. 11. Specific fuel consumption at altitude will.
>> Question Number. 12. During any stabilized running condition, the spill or half ball valve is.
Correct Answer is. Lightly seated.
>> Question Number. 13. What is the purpose of the attenuator fitted between the H.P fuel pump
and the B.P.C in a fuel system?
Correct Answer is. It damps out pulsations in the fuel delivery to the B.P.C.
51
>> Question Number. 14. Why is the hydromechanical governor fitted to a gas turbine engine
fuel pump?
Correct Answer is. To enable the engine to operate over a wide range of fuel SGs.
>> Question Number. 15. A barometric Pressure Controller controls.
Correct Answer is. Fuel flow to suit atmospheric pressure changes.
>> Question Number. 16. Kinetic valves are used because.
Correct Answer is. They are more sensitive.
>> Question Number. 17. When considering a centrifugal type engine speed governor, an
increase in fuel S.G. will cause.
Correct Answer is. A reduction in maximum RPM.
>> Question Number. 18. On a FADEC engine.
Correct Answer is. A channel uses a separate winding of the control alternator to B channel.
>> Question Number. 19. Normal fuel/air ratio for successful combustion is.
>> Question Number. 20. Which of the following influences the operation of an automatic fuel
control unit on a turbojet engine?
Correct Answer is. Burner pressure.
>> Question Number. 21. What is the purpose of the L.P. pump?
Correct Answer is. To prevent cavitation of the H.P Fuel pump.
>> Question Number. 22. The fuel pump plungers are lubricated by.
Correct Answer is. The Fuel.
>> Question Number. 23. Which forces control the maximum RPM governor in a non-
hydromechanical swashplate type of pump?
Correct Answer is. Rotor centrifugal pressure opposed to tension spring loading.
>> Question Number. 24. Why do the holes in the body of the duple burner provide air to the
shroud around the burner head?
Correct Answer is. To minimize carbon formation on the burner face.
>> Question Number. 25. A fuel heater prevents.
Correct Answer is. LP filter icing.
>> Question Number. 26. On a FADEC engine the E.E.C.
Correct Answer is. Has electronic control of the hydro-mechanical fuel control unit in all
modes.
>> Question Number. 27. During normal running conditions, combustion is.
Correct Answer is. self-supporting.
52
>> Question Number. 28. On a FADEC engine, the channel reset.

Correct Answer is. Selects standby which becomes active on the next start.
>> Question Number. 29. With a decrease in fuel SG, what is the result when the engine is fitted
with an uncompensated fuel governor?
Correct Answer is. Maximum RPM increase.
>> Question Number. 30. The maximum RPM of a turbine engine is limited by.
Correct Answer is. Reduction of the fuel pump stroke by a spill valve sensitive to centrifugally
generated fuel pressure.
>> Question Number. 31. To what condition does the fuel flow respond during aircraft
acceleration?
Correct Answer is. Mass airflow rate through the engine.
Explanation. This refers to the parameters that make mass airflow- T2 and N2 in particular.
>> Question Number. 32. During acceleration, the fuel flow is increased at a controlled rate in
order to.
Correct Answer is. Prevent surge and the risk of flame-out.
Explanation. Over fuelling during acceleration is a prime cause of surge.
>> Question Number. 33. The B.P.C controls the F.C.U by.
Correct Answer is. Pressure sensing.
Explanation. BPC is the Barometric Pressure Control.
>> Question Number. 34. If the swash plate of a positive displacement swash plate pump is
perpendicular to the axis of the pump, the flow will be.
Correct Answer is. Zero.
>> Question Number. 35. The burner fuel flow is at maximum at.
Correct Answer is. I.S.A. sea level.
Explanation. Cold dense air requires more fuel than hot warm air to maintain the air-fuel
ratio.
>> Question Number. 36. The type of fuel control unit most commonly used in modern jet engines
is.
Correct Answer is. Hydro-mechanical.
>> Question Number. 37. How is servo pressure, which is used to control fuel pump swash plate
angle, obtained?
Correct Answer is. From pump delivery pressure through variable restrictions.
Explanation. Servo pressure is initially supplied through a fixed restrictor, then modified by
half ball valve and kinetic Knives.
53
>> Question Number. 38. Why is the Barometric Pressure Control fitted in a turboshaft engine
fuel system?
Correct Answer is. To vary pressure pump output in relation to the pressure variation at the
intake.
Explanation. Barometric Pressure Control is an old name for Altitude (and hence air density)
Sensing Unit see Rolls Royce.
>> Question Number. 39. During any stabilized running condition, the spill or half ball valve is.
Correct Answer is. Lightly seated.
>> Question Number. 40. The swash plate in a fuel pump, when static is.
Correct Answer is. In the maximum position.
>> Question Number. 41. A kinetic valve is a device used to control H.P pump output. This is
achieved by movement of a.
Correct Answer is. Knife blade.
>> Question Number. 42. Why is it necessary to control fuel supply to the engine during rapid
acceleration?
Correct Answer is. To prevent excessively high EGT and possible compressor surge.
>> Question Number. 43. Which component corrects for air density effects on fuel/air mixture in
a gas turbine engine?
Correct Answer is. The barometric pressure control unit.
Explanation. Barometric pressure senses density changes.
>> Question Number. 44. Why is the high pressure fuel pump fitted in a gas turbine engine
aircraft?
Correct Answer is. To provide the majority of the fuel pressure to the engine.
>> Question Number. 45. What are the positions of the pressurization valve and the dump valve
in a jet engine fuel system when the engine is shut down?
Correct Answer is. Pressurization valve open, dump valve open.
>> Question Number. 46. The density of air is very important when mixing fuel and air to obtain
a correct fuel to air ratio. Which of the following weighs the most?
Correct Answer is. 100 parts of dry air.
>> Question Number. 47. A mixture ratio of 11:1 normally refers to.
Correct Answer is. 1 part fuel to 11 parts air.
54
>> Question Number. 48. For what primary purpose is a turbine engine fuel control unit trimmed?
Correct Answer is. To obtain maximum thrust output when desired.
>> Question Number. 49. Which type of fuel control is used on most of today's turbine engines?
Correct Answer is. Hydromechanical or electronic.
>> Question Number. 50. Under which of the following conditions will the trimming of a turbine
engine be most accurate?
Correct Answer is. No wind and low moisture.
>> Question Number. 51. An H.M.U receives its signals from.
Correct Answer is. E.E.C.
>> Question Number. 52. In order to stabilize cams, springs, and linkages within the fuel control,
manufacturers generally recommend that all final turbine engine trim adjustments be made in the.
Correct Answer is. Increase direction.
>> Question Number. 53. When trimming a turbine engine, the fuel control is adjusted to.
Correct Answer is. Set idle RPM and maximum speed or E.P.R.
>> Question Number. 54. A supervisory electronic engine control (E.E.C) is a system that receives
engine operating information and.
Correct Answer is. Adjusts a standard hydromechanical fuel control unit to obtain the most
effective engine operation.
>> Question Number. 55. In a FADEC system, active control switchover occurs.
Correct Answer is. On engine start up only.
>> Question Number. 56. What causes the fuel divider valve to open in a turbine engine duplex
fuel nozzle?
Correct Answer is. Fuel pressure.
>> Question Number. 57. The valve on a vane type fuel flow measuring device becomes
stuck. What safety backup is available for the engine fuel flow?
Correct Answer is. A differential pressure bypass valve.
Explanation. Pallett Aircraft Instruments and integrated systems page 369 refers. Note the
valve opens against spring pressure.
>> Question Number. 58. What are the principal advantages of the duplex fuel nozzle used in
many turbine engines?
Correct Answer is. Provides better atomization and uniform flow pattern.
>> Question Number. 59. What is the purpose of the flow divider in a turbine engine duplex fuel
nozzle?
Correct Answer is. Creates the primary and secondary fuel supplies.
55
>> Question Number. 60. Which of the following turbine fuel filters has the greatest filtering action?
Correct Answer is. Micron.
>> Question Number. 61. Where is the engine fuel shutoff valve usually located?
Correct Answer is. Downstream of the engine driven fuel pump.
>> Question Number. 62. Supervisory E.E.C sends its output to the.
Correct Answer is. H.M.U/F.F.G.
Explanation. RB211-535 has this system - the trim signal is passed to the F.F.G. a FADEC
engine would receive trim signals at the H.M.U.
>> Question Number. 63. If a FADEC loses its ADC input. In the short term it will.
Correct Answer is. Go into soft reversion.
Explanation. Sometimes known as the Alternate mode. CF-6 FADEC engine has this facility.
>> Question Number. 64. The primary purpose of an E.E.C is.
Correct Answer is. To save fuel, reduce crew workload and reduce maintenance costs.
Explanation. Inputs and outputs to the FADEC are both digital and analogue, hence a and b
are both wrong. Optimized performance is the reason FADEC was introduced
>> Question Number. 65. When both FADEC channels are healthy they will alternate.
Correct Answer is. On each engine start.
>> Question Number. 66. The purpose of the LP fuel pump is to.
Correct Answer is. Ensure the H.P fuel pump does not cavitate.
Explanation. Maintains about 40 psi to the inlet of the H.P Pump.
>> Question Number. 67. In a FADEC system, what is the result of Channel A failing to receive
information from a sensor?
Correct Answer is. Channel A will take the information from channel B.
Explanation. This assumes that channel A is still capable of full control and that channel B
is receiving a good sensor signal.
>> Question Number. 68. In a FADEC engine with a hydromechanical fuel system, how is fuel
flow controlled?
Correct Answer is. By electro-hydraulic servo valves (E.H.S.Vs).
>> Question Number. 69. on the approach.
Correct Answer is. RPM should be above the minimum idle for maximum acceleration.
Explanation. A high (or flight) idle setting is used for maximum acceleration in the event of
overshoot.
>> Question Number. 70. The air data inputs to the FADEC E.C.U fails. The result will be:.
Correct Answer is. The E.C.U reverts to the fail-safe mode.
56
Explanation. If all air data input fails then the E.C.U reverts to an alternate (Fail-safe) mode.
>> Question Number. 71. A FADEC system consists of.
Correct Answer is. H.M.U, sensors and an E.E.C.
>> Question Number. 72. A fuel heater prevents.
Correct Answer is. Entrained water in fuel freezing. Freezing it is the entrained water that
froze first.
>> Question Number. 73. When re-light is required in flight on a FADEC engine, the pilot selects.
Correct Answer is. Igniter selected automatically.
Explanation. The FADEC chooses whichever igniter it wants.
>> Question Number. 74. The position of fuel heater in fuel system is.
Correct Answer is. Before the LP fuel filter.
Explanation. This position ensures the fuel will not freeze in the fuel filter.
>> Question Number. 75. The E.E.C receives its primary power from.
Correct Answer is. Separate permanent magnet alternator.
>> Question Number. 76. The fuel trimmer on a turbo-prop engine is operated.
Correct Answer is. Automatically controlled in conjunction with FCU.
Explanation. No Turbo-prop aircraft has a manual fuel trimmer as far as we are aware.
>> Question Number. 77. The main advantage of FADEC is.
Correct Answer is. Efficiency is always maximum.
Explanation. Reduced pilot workload and maximum efficiency of performance is the greatest
advantage of F.A.D.E.C.
>> Question Number. 78. Inlet side of a fuel pump has a.
Correct Answer is. Wire mesh filter.
>> Question Number. 79. When a throttle is selected to increase power, the pressure drop
across the Fuel Control Unit throttle orifice.
Correct Answer is. Drops then increases due to increasing pump output.
Explanation. On selection the pressure drop across the throttle decreases then recovers as
the pump increases the flow of fuel.
>> Question Number. 80. When the E.E.C supervisory circuit senses a fault on the engine, the
fault annunciator light will be on and the E.E.C will.
Correct Answer is. Remove fuel, down trimming signal immediately.
>> Question Number. 81. In-Flight the engine E.E.C controls.
Correct Answer is. Fuel flow.
57
Explanation. Throttle position is controlled by the crew or auto throttle. EGT is a function of
fuel flow.
>> Question Number. 82. A FADEC does not have which of the following?
Correct Answer is. Automatic control of engine fire bottles.
Explanation. Fire extinguishers are always operated from the flight deck.
>> Question Number. 83. A FADEC consists of.
Correct Answer is. Electronic controls, sensors and an H.M.U.
Explanation. A FADEC is the full system of sensors and control unit. Sometimes the Hydro
mechanical Unit (H.M.U) is also included as part of the system.
>> Question Number. 84. During aerobatic manoeuvres, what prevents fuel from spilling out of
fuel tank vents?
Correct Answer is. Float operated valves.
Explanation. Float operated valves allow the vent lines to vent both ways if there is no fuel
on the float, but will `shut when the float is lifted by fuel.
>> Question Number. 85. After a bag tank replacement, where would you disconnect the system
to carry out the flow checks?
Correct Answer is. At the engine.
Explanation. CAIPs AL/3-17 states that for any aircraft fuel flow test after major system
interruption connect the flow rig at the engine bulkhead.
>> Question Number. 86. What is the purpose of a silver strip on a fuel filter?
Correct Answer is. To detect Sulphur in fuel.
>> Question Number. 87. The basic concept of an H.P fuel control is.
Correct Answer is. Constant adjustment of the swash plate angle of the H.P fuel pump.
>> Question Number. 88. To prevent compressor surge and overheating of the combustion
chamber due to over fuelling.
Correct Answer is. An acceleration control unit is fitted.
Explanation. The acceleration unit automatically limits the rate of increase of fuel flow until
sufficient air is passing through the engine.
>> Question Number. 89. When FADEC is in normal mode.
Correct Answer is. Channel A or B will be in command.
Explanation. Both channels are operating but either one can be in control if they are both
healthy.
>> Question Number. 90. Out of the following thrust lever resolver angles, which one is the
forward idle setting?
58
Correct Answer is. 40 degrees.

Explanation. All FADEC engines will have reverse thrust settings therefore the T.L.A of 0
degrees will be max reverse, and 85 will be max forward therefore 40 is the idle figureure.
>> Question Number. 91. Trimming is a term applied to adjusting the.
Correct Answer is. Idle speed and maximum thrust.
Explanation. Dale Crane Dictionary of Aeronautical Terms 3rd edition Refers.
>> Question Number. 92. Fuel boost pumps are cooled using.
Correct Answer is. Fuel.
Explanation. Fuel pumps, of any type usually use the fuel they are pumping to cool the
bearings.
>> Question Number. 93. A fuel trimmer unit is adjusted at altitude.
Correct Answer is. Automatically, via a fuel trim unit.
Explanation. We assume here that the fuel trim at altitude is due to decreasing air density&
pressure. The Fuel flow governor (fuel trimmer) does this automatically.
>> Question Number. 94. Baffles in a rigid fuel tank.
Correct Answer is. Prevent surge.
Explanation. This question was definitely asked in module 15- it should be in module 11
>> Question Number. 95. In a FADEC system, what does the E.E.C measure along with RPM?
Correct Answer is. Pressure and Temperature.
Explanation. Normally the E.E.C reads as a minimum To Po Ps3 and T25.
>> Question Number. 96. In a FADEC system, how are the power supply windings for channel A
and Channel B wound?
Correct Answer is. On one generator with 2 separate windings.
Explanation. The engine alternator is a permanent magnet alternator with 2 windings within
the stator housing. There may also be a third winding that is used to indicate H.P RPM (H.P
tachometer) within the same housing.
>> Question Number. 97. If an Engine FADEC system loses air-data permanently, the pilot will.
Correct Answer is. Switch to Alt on the relevant E.E.C.
Explanation. By switching to Alternate mode manually the E.E.C uses cornerstone Pamb
and Tamb.
>> Question Number. 98. A FADEC system takes measurements from Engine Speed,
Correct Answer is. Temperature and Pressure.
Explanation. T-ambient, P-ambient and P s3 as a minimum.
>> Question Number. 99. Main purpose of the fuel boost pumps is to provide.
59
Correct Answer is. Fuel pressure to both engine pumps.

Explanation. Supply of fuel to the engines is the primary purpose although the other two
answers may also be options.
>> Question Number. 100. The swash plate in the fuel pump of an axial flow gas turbine engine
is controlled by.
Correct Answer is. Servo fuel pressure.
>> Question Number. 101. The end fittings on a fuel non-return valve are normally of different
sizes to.
Correct Answer is. Prevent incorrect installation.
Explanation. Also known as check valves, NRV's have different end fittings and sometimes
an arrow showing direction of flow embossed on the casing.
>> Question Number. 102. E.E.C receives signals from RPM sensor and.
Correct Answer is. Pressure and temperature sensors.
Explanation. Modern FADEC systems receive all three types of sensor but quite often do not
use the EGT signals for control.
>> Question Number. 103. When does E.E.C channel change over occur?
Correct Answer is. On engine start up.
Explanation. The E.E.C prepares for the changeover by resetting the E.E.C on shut down,
but does not actually do it until the next start. A simple single fault (compared to a complete
channel failure) will not cause a change over.
>> Question Number. 104. The possible combined output from all the scavenge pumps in a
lubrication system will be.
Correct Answer is. Greater than the pressure pump output.
>> Question Number. 105. If the knife-edge blade in a kinetic valve is fully in.
Correct Answer is. Servo pressure is being bled off.
60
15.12 Air Systems.

>> Question Number. 1. Engine anti-ice is taken from the.
Correct Answer is. H.P compressor.
>> Question Number. 2. In an axial flow turbine engine, compressor bleed air is sometimes used
to aid in cooling the.
Correct Answer is. Turbine, vanes, blades, and bearings.
>> Question Number. 3. If air is taken from the compressor for air conditioning or anti-icing.
Correct Answer is. Thrust will decrease EGT will increase.
Explanation. Air is taken from the H.P compressor hence there is less mass flow.
>> Question Number. 4. Turbine case cooling utilizes.
Correct Answer is. Fan air.
Explanation. Fan air is the coldest in the engine.
>> Question Number. 5. Air for anti-icing is taken from the.
Correct Answer is. H.P compressor.
Explanation. LP air would not be hot enough.
>> Question Number. 6. As air is bled off the engine, EGT will.
Explanation. Less air, but same fuel equals higher EGT.
>> Question Number. 7. The heat absorbed by internal components can be detrimental to thrust
and is prevented by.
Correct Answer is. Bleeding air off the compressor to cool the components.
>> Question Number. 8. On a gas turbine engine, thermal wing de-icing system derives air.
Correct Answer is. Through a pressure regulating shut-off valve (P.R.S.O.V).
Explanation. Rolls Royce The Jet Engine Page 150 Refers.
>> Question Number. 9. Inlet for cooling air for the first stage turbine blades is fed via the.
Correct Answer is. Blade root.
Explanation. The cooling air is ducted through the turbine disc to the blade root then out into
the airstream through holes in the leading and trailing edges.
>> Question Number. 10. Air bleed for an anti-ice system is.
Correct Answer is. Tapped directly off the compressor.
Explanation. With this method if the engine is running then anti-ice air is always available.
>> Question Number. 11. With bleed valves open for anti-ice.
Correct Answer is. Thrust decreases, fuel consumption decreases.
61
15.13, Starting and Ignition Systems.

>> Question Number. 1. In the H.E.I.U. the discharge resistors.
Correct Answer is. Allows the capacitors to discharge when the unit is switched off.
>> Question Number. 2. In the H.E.I.U. the choke.
Correct Answer is. Prolongs the discharge.
>> Question Number. 3. In an electrical starting system, the slow start resistor is short circuited
by the.
Correct Answer is. Centrifugal Switch.
>> Question Number. 4. The advantage of an air starter system is.
Correct Answer is. It is light, simple and economical.
>> Question Number. 5. An advantage of a gas turbine starter is.
Correct Answer is. It provide high power for low weight.
>> Question Number. 6. If the engine fails to light-up, the starter cycle is canceled by.
Correct Answer is. A time switch.
>> Question Number. 7. For starting the engine, the H.P cock should be initially.
>> Question Number. 8. On light up, the gas temperature will.
Correct Answer is. Rise rapidly, then fall as RPM increases to idle.
>> Question Number. 9. Self-sustaining RPM means that.
Correct Answer is. The engine will run independently of external help.
>> Question Number. 10. A 'hot start' with excessive temperatures may be caused by.
Correct Answer is. Throttle partly open.
>> Question Number. 11. A dry motoring cycle would be required to.
Correct Answer is. Clear the engine after a wet start.
>> Question Number. 12. What type of turbine blade is most commonly used in air starter motors?
Correct Answer is. Impulse.
>> Question Number. 13. Ignitor plugs are cleaned by.
Correct Answer is. Compressed air and brushing lightly with soft brush.
>> Question Number. 14. An H.E.I.U works by.
Correct Answer is. A discharging capacitor.
>> Question Number. 15. When is ignition used?
Correct Answer is. For relight and start up.
>> Question Number. 16. An ignitor plug for a large gas turbine takes the form of a.
Correct Answer is. Surface discharge plug.
62
>> Question Number. 17. The spark in the High Energy igniter is supplied by.
Correct Answer is. A capacitor.
>> Question Number. 18. Self-sustaining speed is.
Correct Answer is. The RPM at which the engine continues without external assistance.
Explanation. After the starter has cut out and the RPM and TGT have stabilized.
>> Question Number. 19. during normal running conditions.
Correct Answer is. Combustion is self-supporting
>> Question Number. 20. High energy ignition is required because of the.
Correct Answer is. High flash point of the fuel.
>> Question Number. 21. In the H.E.I.U. the discharge resistors.
Correct Answer is. Allow the capacitors to discharge when the unit is switched off.
>> Question Number. 22. The rate of discharge of an H.E.I.U. is.
Correct Answer is. 60 - 100 per minute.
>> Question Number. 23. Why do turbine engine ignition systems require high energy?
Correct Answer is. To ignite the fuel under conditions of high altitude and low temperatures.
>> Question Number. 24. The type of ignition system used on most turbine aircraft engines is.
Correct Answer is. Capacitor discharge.
>> Question Number. 25. A safety feature usually employed in pneumatic starters that is used to
prevent the starter from reaching burst speed if inlet air does not terminate on schedule is the.
Correct Answer is. Stator nozzle design that chokes airflow and stabilizes turbine wheel
speed.
>> Question Number. 26. A safety feature usually employed in pneumatic starters that is used if
the clutch does not
Release from the engine drive at the proper time during start is the.
Correct Answer is. Flyweight cutout switch.
>> Question Number. 27. Airflow to the pneumatic starter from a ground unit is normally prevented
from causing starter overspeed during engine start by.
Correct Answer is. Activation of a flyweight cutout switch.
>> Question Number. 28. Air turbine starters are generally designed so that reduction gear
distress or damage may be detected by.
Correct Answer is. Inspection of a magnetic chip detector.
>> Question Number. 29. Inspection of pneumatic starters by maintenance technicians usually
includes checking the.
Correct Answer is. Oil level and magnetic drain plug condition.
63
>> Question Number. 30. Pneumatic starters are usually designed with what types of airflow
impingement systems?
Correct Answer is. Radial inward flow turbine and axial-flow turbine.
>> Question Number. 31. A clicking sound heard at engine coast-down in a pneumatic starter
incorporating a sprag clutch ratchet assembly is an indication of.
Correct Answer is. The pawls re-contacting and riding on the ratchet gear.
>> Question Number. 32. The primary advantage of pneumatic (air turbine) starters over
comparable electric starters for turbine engines is.
Correct Answer is. High power-to-weight ratio.
>> Question Number. 33. The purpose of an undercurrent relay in a starter-generator system is
to.
Correct Answer is. Disconnect power from the starter-generator and ignition when sufficient
engine speed is reached.
>> Question Number. 34. How does the ignition system of a gas turbine engine differ from that of
a reciprocating engine?
Correct Answer is. A high energy spark is required for ignition.
>> Question Number. 35. In a gas turbine engine D.C capacitor discharge ignition system, where
are the high voltage pulses formed?
Correct Answer is. At the triggering transformer.
>> Question Number. 36. Igniter plugs used in turbine engines are subjected to high intensity
spark discharges and yet they have a long service life because they.
Correct Answer is. Do not require continuous operation.
>> Question Number. 37. Great caution should be exercised in handling damaged hermetically
sealed turbine engine igniter transformer units because.
Correct Answer is. Some contain radioactive material.
>> Question Number. 38. Generally, when removing a turbine engine igniter plug, in order to
eliminate the possibility of the technician receiving a lethal shock, the ignition switch is turned off
and disconnecting the igniter lead from the plug and waiting the prescribed time.
Correct Answer is. The igniter lead is disconnected from the plug and the center electrode
grounded to the engine after disconnecting the transformer-exciter input lead and waiting the
prescribed time.
>> Question Number. 39. What is the first engine instrument indication of a successful start of a
turbine engine?
Correct Answer is. A rise in the exhaust gas temperature.
64
>> Question Number. 40. H.E.I.U ignitor plugs receive their electrical supply from.
Correct Answer is. Discharge capacitor.
>> Question Number. 41. An H.E.I.U is rated in.
Correct Answer is. Joules.
>> Question Number. 42. A glow plug operates.
Correct Answer is. By heat action.
Explanation. The extreme heat of the plug ignites the fuel. It is powered by electricity.
>> Question Number. 43. The resistor in a D.C. starter motor.
Correct Answer is. Prevents current surge when motor is at low rpm.
>> Question Number. 44. Where does the high voltage type turbine ignition receive its voltage
pulse from?
Correct Answer is. Primary windings.
Explanation. Rolls Royce the jet engine Fig 11-12 shows an AC system. This uses a
transformer to generate the high voltage at the discharge gap.
>> Question Number. 45. On a gas turbine engine DC starting circuit, if there is an open circuit
on the contact of the over speed relay.
Correct Answer is. No power supply is connected to the starter motor.
Explanation. The main relay cannot close if the overspeed relay is open.
>> Question Number. 46. The field of the D.C. starter motor used on gas turbine engine is.
Correct Answer is. Series or compound.
Explanation. Aircraft electrical systems E.H.J Pallett 3rd edition page 154 refers.
>> Question Number. 47. When 'blow out' is selected on the Gas Turbine Engine starting circuit.
Correct Answer is. The starter motor is stopped when starter switch selected off or when the
timer switch cuts out.
Explanation. Refer Fig 11-3 Rolls Royce The Jet Engine. The blow out circuit is used to blow
out any jet pipe fire. In this mode there is no ignition or fuel hence the starter cannot overspeed.
>> Question Number. 48. After an unsuccessful start of an engine.
Correct Answer is. Unburnt fuel can be evacuated by motoring the engine with H.P cock
closed.
Explanation. On normal shutdowns combustors and fuel manifolds are drained through the
drain manifold. After an unsuccessful start there will be fuel throughout the hot section. Hence a
dry run is needed to purge the engine.
>> Question Number. 49. A glow plug may be used in place of a spark plug on.
Correct Answer is. Small engines.
65
>> Question Number. 50. When an engine being started by an air starter reaches self-sustaining
speed.
Correct Answer is. The starter valve is disconnected by the fly weight cut-out switch in the
air starter.
>> Question Number. 51. When reconnecting a H.E.I.U , which cable must be reconnected
first?
Correct Answer is. H.T before L.T.
Explanation. This is the reverse of disconnecting, when L.T is isolated and then disconnected
first.
>> Question Number. 52. An aircraft flying through heavy rain may use, as a precaution.
Correct Answer is. Continuous ignition.
Explanation. Continuous ignition is used in case of flame out caused by the inclement
weather.
>> Question Number. 53. The starter light is on during a start cycle (low voltage electrical starter).
Correct Answer is. If the light stays on after 30 seconds action is required.
Explanation. See the Rolls Royce Jet engine low voltage starter system on page 123. The
indicator light indicates power to the igniter. The Full current time switch cuts out the circuit after
a period of time.
>> Question Number. 54. A D.C starter motor disconnects due to.
Correct Answer is. Current decreasing switching off an overspeed relay.
Explanation. Same starter circuit reference as above. As the starter accelerates drawn
current reduces and causes the overspeed relay to drop out.
>> Question Number. 55. What is the purpose of the current limiting resistor in a starter circuit?
Correct Answer is. To prevent an initial current surge.
Explanation. The starter motor is protected from excessive current until the timer shorts out
the resistor. See RR the jet engine page 123.
>> Question Number. 56. On a low energy dual ignition system (<3 joules), if a relight is
necessary.
Correct Answer is. The pilot selects both ignitors.
Explanation. Normal low/high systems have a choice of low or high energy ignition with high
being used for relight. In these systems the pilot can choose 1, 2 or both.
66
15.14, Engine Indication Systems.

>> Question Number. 1. The compensation device on an E.G.T system must be re-calibrated
after.
Correct Answer is. Does not need calibration.
Explanation. The compensation device is an automatic device Page 140 Rolls Royce book
refers.
>> Question Number. 2. When testing an E.G.T system.
Correct Answer is. The O.A.T is always taken into consideration.
Explanation. To test the system the test set has to trimmed for ambient temperature, as the
system when in operation is adjusted for ambient temperature by the compensating resistor. This
is clearly stated in the B 737 AMM.
>> Question Number. 3. What is the Engine Pressure Ratio (E.P.R.) used for?
Correct Answer is. To indicate the thrust produced by the engine.
>> Question Number. 4. What happens when bulb type thermometer resistive element goes open
circuit?
Correct Answer is. Reads more than ambient.
>> Question Number. 5. On an E.G.T thermocouple system, the hot junction.
Correct Answer is. Is placed downstream of the combustion chamber.
>> Question Number. 6. On an RPM system using a synchronous generator, the pointer is
deflected by.
Correct Answer is. An AC servomotor.
>> Question Number. 7. Torque pressure is usually read from a.
Correct Answer is. Direct reading pressure gauge.
>> Question Number. 8. The drag cup in a tacho-generator is balanced by.
Correct Answer is. Calibrated hairspring.
>> Question Number. 9. Fuel flow indication is taken from.
Correct Answer is. After either H.P Pump or LP Pump.
Explanation. Vane type flowmeters are usually in the LP Supply. Integrated flowmeters in
the H.P supply.
>> Question Number. 10. What power is required for E.G.T gauge indication?
Correct Answer is. No power - it is self-generating.
>> Question Number. 11. A Bourdon tube instrument may be used to indicate.
Correct Answer is. Pressure and temperature.
67
>> Question Number. 12. What instrument on a gas turbine engine should be monitored to
minimize the possibility of a 'hot' start?
>> Question Number. 13. Oil temperature thermocouples are usually constructed of.
Correct Answer is. Iron constantan.
>> Question Number. 14. The RPM indication of a synchronous AC motor tachometer is
governed by the generator.
Correct Answer is. Frequency.
>> Question Number. 15. Instruments that measure relatively high fluid pressures, such as oil
pressure gauges, are usually what type?
Correct Answer is. Bourdon tube.
>> Question Number. 16. Instruments that provide readings of low or negative pressure, such as
manifold pressure gauges, are usually what type?
Correct Answer is. Diaphragm or bellows.
>> Question Number. 17. In what units are gas turbine engine tachometers calibrated?
Correct Answer is. Percent of engine RPM.
>> Question Number. 18. In a turbine engine, where is the turbine discharge pressure
indicator sensor located?
Correct Answer is. Immediately aft of the last turbine stage.
>> Question Number. 19. The exhaust gas temperature (E.G.T) indicator on a gas turbine engine
provides a relative indication of the.
>> Question Number. 20. Engine pressure ratio is determined by.
Correct Answer is. Dividing turbine outlet total pressure by engine inlet total pressure.
>> Question Number. 21. A red triangle, dot, or diamond mark on an engine instrument face or
glass indicates.
Correct Answer is. The maximum limit for high transients such as starting.
>> Question Number. 22. What is the primary purpose of the tachometer on an axial compressor
turbine engine?
Correct Answer is. Monitor engine RPM during starting and to indicate overspeed conditions.
>> Question Number. 23. Engine pressure ratio is the total pressure ratio between the.
Correct Answer is. Front of the compressor and the rear of the turbine.
>> Question Number. 24. On an aircraft turbine engine, operating at a constant power, the
application of engine anti-icing will result in.
68
Correct Answer is. Noticeable shift in E.P.R.

>> Question Number. 25. The indicator of a tachometer system is responsive to change in.
>> Question Number. 26. The fuel flow indication data sent from motor driven impeller and
turbine, and motorless type fuel flow transmitters is a measure of.
Correct Answer is. Fuel mass flow.
>> Question Number. 27. In addition to fuel quantity, a computerized fuel system (C.F.S) with a
totalizer indicator provides indication of how many of the following?
Correct Answer is. Fuel flow rate, Fuel used since reset or initial startup, Fuel time remaining
at current power setting.
>> Question Number. 28. The fuel flow indicator rotor and needle for a motor impeller and turbine
indicating system is driven by.
Correct Answer is. An electrical signal.
>> Question Number. 29. Motor driven impeller and turbine fuel flow transmitters are designed to
transmit data.
Correct Answer is. Using aircraft electrical system power.
>> Question Number. 30. What unit in a tachometer system sends information to the indicator?
Correct Answer is. The three phase AC generator.
>> Question Number. 31. Engine oil temperature gauges indicate the temperature of the oil.
Correct Answer is. Entering the oil cooler.
Explanation. Rolls Royce book fig 8-7.
>> Question Number. 32. Thermocouple leads.
Correct Answer is. Are designed for a specific installation and may not be altered.
>> Question Number. 33. Why do helicopters require a minimum of two synchronous tachometer
systems?
Correct Answer is. One indicates engine RPM and the other main rotor RPM.
>> Question Number. 34. If the thermocouple leads were inadvertently crossed at installation,
what would the E.G.T gauge pointer indicate?
Correct Answer is. Moves off scale on the zero side of the meter.
>> Question Number. 35. A common type of electrically operated oil temperature gauge utilizes.
Correct Answer is. Either a wheatstone bridge or ratiometer circuit.
>> Question Number. 36. The indication on a thermocouple-type E.G.T indicator is produced by.
Correct Answer is. A current generated by the temperature difference between dissimilar
metal hot and cold junctions.
69
>> Question Number. 37. What is the Engine Pressure Ratio (E.P.R) used to indicate?
Correct Answer is. The thrust produced by the engine.
Explanation. Normally used on High Bypass Engines.
>> Question Number. 38. Where is Turbine Outlet Temperature (T.O.T) measured?
Correct Answer is. Downstream of the turbine.
Explanation. It can be in the jet pipe or more normally today in between turbine stages or
even within NGV's.
>> Question Number. 39. A thermocouple indicator is basically a.
Correct Answer is. Millivolt meter.
Explanation. A thermocouple generates an E.M.F between hot and cold junction, hence the
gauge is a millivolt meter.
>> Question Number. 40. A thermocouple indicator is connected to the.
Correct Answer is. Cold junction.
>> Question Number. 41. Thrust in a high bypass fan engine is indicated by.
Correct Answer is. N1 RPM or E.P.R.
Explanation. RR and P&W tend to use E.P.R. GE use N1.
>> Question Number. 42. How is the N1 and N2 measured on a triple spool engine?
Correct Answer is. Pulse type speed probes.
>> Question Number. 43. Modern oil pressure servo transmitters sense.
Correct Answer is. Differential pressure.
>> Question Number. 44. E.G.T thermocouples are usually made of.
81 of 111 03-May-18, 4:52 PM
Correct Answer is. chromel and alumel.
>> Question Number. 45. Thrust in a high bypass engine is indicated by measuring.
Correct Answer is. Neither of the above, thrust is not indicated in flight.
Explanation. The only indication of power in flight is E.P.R or, for a high bypass engine, N1
RPM.
>> Question Number. 46. What power supply is required for a thermocouple system to work?
Correct Answer is. Neither of the above.
Explanation. Rolls Royce the Jet engine Page 139 refers.
>> Question Number. 47. In a thermocouple temperature sensing system, what is the purpose of
the compensating resistor?
Correct Answer is. To correct for varying ambient temperatures at the cold junction.
>> Question Number. 48. In a tachometer generator.
70
Correct Answer is. Frequency output is proportional to engine speed.

>> Question Number. 49. Vibration pick-ups are located.
Correct Answer is. On both fan and turbine cases.
Explanation. Can be on one or both, depending upon the engine.
>> Question Number. 50. In a capacitive type fuel quantity indicating system the tank units are
connected in.
Correct Answer is. Parallel.
>> Question Number. 51. Torque measurement in a gas turbine engine is.
Correct Answer is. Required only when the turbine drives a propeller.
>> Question Number. 52. Vibration signals, when picked up,
Correct Answer is. The frequencies are filtered to exclude unwanted frequencies.
Explanation. The filters in the Vibro-meter use rotor speed to identify vibration frequencies.
>> Question Number. 53. E.G.T is displayed in.
Correct Answer is. Degrees centigrade.
Explanation. E.G.T is always measured in centigrade.
>> Question Number. 54. N2 is taken from.
Correct Answer is. A tachometer on the accessory gearbox.
Explanation. The N2 gearbox is driven by the N2 compressor. A single winding of an
alternator can be used for the speed signal as an alternative to a.
>> Question Number. 55. Engine vibration is monitored using.
Correct Answer is. Piezoelectric accelerometer.
Explanation. Piezoelectric devices convert force (from the vibration) to a milli-volt output.
>> Question Number. 56. Integrating fuel flow gives.
Correct Answer is. Total fuel consumed.
Explanation. An Integrator is incorporated in a fuel flow-meter to give a total fuel used figure.
>> Question Number. 57. The gauge on a bulb type temperature indicator shows zero. This could
be caused by.
Correct Answer is. Two cables shorting together by the sensor.
Explanation. Pallett Instruments and Integrated systems Page 318 refers. A short will remove
all power from both windings and the pointer will go tominimum scale.
>> Question Number. 58. In a thermocouple system, the size of the E.M.F that is produced is a
result of.
Correct Answer is. The difference between the hot and cold junction.
Explanation. The E.M.F is a result of the difference between the 2 junctions.
71
>> Question Number. 59. A ballast resistor is fitted.

Correct Answer is. In series, to give identical resistance values to all airframes.
72
15.15, Power Augmentation Systems

>> Question Number. 1. When reheat is used, E.P.R.
Correct Answer is. Remains constant.
Explanation. Rolls Royce The jet engine page 175 states that as P6 increases in the jet pipe
the nozzles are opened to reduce P6 back to its normal value.
>> Question Number. 2. When reheat is selected and in operation, the mass gas flow.
Correct Answer is. Remains the same.
>> Question Number. 3. Screech liners in the afterburning jet pipe.
Correct Answer is. Prevent cyclic vibrations of large amplitude.
>> Question Number. 4. Water methanol for cooling is injected into the.
Correct Answer is. Compressor inlet or outlet.
>> Question Number. 5. On an injection system.
Correct Answer is. Demineralized water/methanol is injected.
>> Question Number. 6. When using water methanol in an axial flow compressor, it is injected
into the.
Correct Answer is. Compressor inlet or burner section.
>> Question Number. 7. The main reason for adding methanol to the water is to.
Correct Answer is. Prevent mixture freezing.
>> Question Number. 8. The primary purpose of water injection is to.
Correct Answer is. Cool the turbine.
Explanation. Notice that the answers did not include 'increase mass airflow'. Cooling the
turbine is the primary purpose if the water is injected in the combustor outlet manifold.
>> Question Number. 9. Water used in a thrust augmentation system should be demineralized to
prevent.
Correct Answer is. Fouling the blades and vanes.
>> Question Number. 10. The quantity of water usually carried by an aircraft equipped with water
injection is enough for.
Correct Answer is. One take-off.
>> Question Number. 11. Water methanol injection will increase thrust by up to.
>> Question Number. 12. Injection of water/methanol into compressor inlet causes.
Correct Answer is. Increase in power without the need for burning extra fuel.
>> Question Number. 13. Reheat is the term used to describe.
Correct Answer is. Adding fuel in the exhaust section.
73
>> Question Number. 14. Water/methanol is injected.

Correct Answer is. At high temperatures or high altitudes.
>> Question Number. 15. The reheat ignition system which incorporates a platinum/rhodium
element is known as.
Correct Answer is. Catalytic ignition.
Explanation. Fuel sprayed on to the catalytic element heats up and ignites.
>> Question Number. 16. Water or water/methanol injected into the combustion chamber inlet
increases.
Correct Answer is. Mass airflow through the turbine.
>> Question Number. 17. Methanol is added to water when augmenting thrust in order to.
Correct Answer is. Reclaim lost heat at the turbines.
Explanation. Methanol burns, but its heat output is low. Its prime purpose is to act as an
antifreeze in the water.
>> Question Number. 18. Afterburning is initiated in order to.
Correct Answer is. Increase the local speed of sound at the jet nozzle.
Explanation. A faster SoS allows for greater momentum thrust at the exhaust nozzle.
>> Question Number. 19. How is the flame stabilized in the reheat system of a gas turbine engine?
Correct Answer is. By ensuring that the gas velocity is greater than the flame velocity.
Explanation. The guttering in the reheat manifolds allows the flame to stabilize at the point.
>> Question Number. 20. During operation of the engine equipped with water injection system,
the metering of the coolant to the system is.
Correct Answer is. Selected by the pilot.
Explanation. Water injection is used on takeoff as required by the pilot.
>> Question Number. 21. Water methanol injection is used.
Correct Answer is. At higher than normal ambient air temperatures only.
Explanation. Water Methanol adds to the weight of the air thus compensating for reduced
density.
74
15.16, Turbo-prop Engines

>> Question Number. 1. A free turbine is usually found on a.
Correct Answer is. Turbo prop.
>> Question Number. 2. A free turbine is.
Correct Answer is. Connected directly to the power output shaft.
>> Question Number. 3. The fuel flow in a turboprop engine within the constant speed range is
controlled.
Correct Answer is. Automatically.
Explanation. Once the power lever has set the gas generator RPM it is controlled
automatically to maintain the constant speed.
>> Question Number. 4. Torque measurement is taken from the.
Correct Answer is. Reduction gearbox.
>> Question Number. 5. Electrical propeller de-icing pads are.
Correct Answer is. At the root.
Explanation. On the leading edge from the root outward.
>> Question Number. 6. Fuel trimming on a turboprop engine is.
Correct Answer is. Governor controlled.
>> Question Number. 7. What controls the fuel trimmer on a turboprop engine?
Correct Answer is. Engine Speed Governor.
>> Question Number. 8. What is the purpose of the reduction gear on a propeller driven engine?
Correct Answer is. To prevent the propeller tips reaching the speed of sound.
Explanation. Reduction ratios vary between 13.5:1 and 10:1.
>> Question Number. 9. If an E.P.R gauge is installed on turbofans as a measure of power output,
what is used on a turboprop?
Correct Answer is. Torque-meter.
Explanation. Torque is used because it is measuring the resistance to rotation of the
propeller, which is turned by the power of the engine.
>> Question Number. 10. What type of reduction gear is used on most turboprop modern
engines?
Correct Answer is. Epicyclic reduction gear.
Explanation. Epicyclic gearing is essential to enable the very large torque to be safely
absorbed.
75
15.17, Turbo-Shaft Engines.

>> Question Number. 1. A turbo-shaft engine has.
Correct Answer is. A power shaft which is not connected to the compressor.
>> Question Number. 2. On a twin spool turbo-shaft engine, the free turbine is connected to the.
Correct Answer is. Output gearbox.
Explanation. The output gearbox will normally contain a reduction gear system and torque
measuring equipment.
>> Question Number. 3. In the majority of helicopters, the thrust generated by the gas generator
is absorbed by the.
Correct Answer is. Free power turbine.
Explanation. The power turbine drives a reduction/rotor transmission gearbox.
76
15.18, Auxiliary Power Units (APUs).

>> Question Number. 1. An A.P.U has.
Correct Answer is. Constant speed and is self contained.
>> Question Number. 2. An A.P.U shut down is initiated by.
Correct Answer is. Low oil pressure, fire warning, hot oil temperature.
Explanation. Honeywell 331-200 A.P.U handbook refers.
>> Question Number. 3. An A.P.U start cycle is completed at.
Correct Answer is. 95% RPM.
>> Question Number. 4. An A.P.U power lever is located.
Correct Answer is. An A.P.U is fully automatic and does not require a power lever.
>> Question Number. 5. An A.P.U consists of.
Correct Answer is. A power compressor and load compressor.
Explanation. The power compressor generates the pressure to drive the system, the load
compressor supplies air to the aircraft pneumatic system.
>> Question Number. 6. When necessary, A.P.U engine cooling before shutdown may be
accomplished by.
Correct Answer is. Closing the bleed air valve.
>> Question Number. 7. Frequently, an aircraft's auxiliary power unit (A.P.U) generator.
Correct Answer is. Is identical to the engine-driven generators.
>> Question Number. 8. Fuel scheduling during A.P.U start and under varying pneumatic
bleed and electrical loads is maintained.
Correct Answer is. Automatically by the A.P.U fuel control system.
>> Question Number. 9. An A.P.U is usually rotated during start by.
Correct Answer is. An electric starter.
>> Question Number. 10. Usually, most of the load placed on an A.P.U occurs when.
Correct Answer is. The bleed air valve is opened.
>> Question Number. 11. The function of an A.P.U air inlet plenum is to.
Correct Answer is. Stabilize the pressure of the air before it enters the compressor.
>> Question Number. 12. in a large commercial passenger transport aircraft the A.P.U supplies.
Correct Answer is. Pneumatics and electrics.
>> Question Number. 13. When in operation, the speed of an A.P.U.
Correct Answer is. Remains at or near rated speed regardless of the load condition.
>> Question Number. 14. Generally, when maximum A.P.U shaft output power is being used in
conjunction with pneumatic
77
Correct Answer is. Pneumatic loading will be automatically modulated to maintain a safe
E.G.T.
>> Question Number. 15. For an A.P.U to run 'unmanned' it must be equipped with.
Correct Answer is. Both an audible fire warning and an automatic fire extinguishing system.
Explanation. The audible warning is external and internal and auto fire extinguishing (when
the engines are not running) is normal.
>> Question Number. 16. An A.P.U is.
Correct Answer is. A self-contained constant speed gas turbine engine.
>> Question Number. 17. When the A.P.U is running and pneumatics are on.
Correct Answer is. Bleed valve is open, surge valve is closed.
>> Question Number. 18. When is the A.P.U at its greatest load?
Correct Answer is. With bleeds open and with generator loads on line.
Explanation. Modern A.P.U's supply pneumatics and electrical power.
>> Question Number. 19. Auxiliary power units provide.
Correct Answer is. Pneumatic and electrical power.
Explanation. Electrical power is normally available up to the service ceiling with pneumatics
up to about 17000 ft (Boeing B-757/767).
>> Question Number. 20. When starting an A.P.U what would the normal duty cycle be on a
modern aircraft?
Correct Answer is. 3 attempted starts per hour with 5 minutes between each attempt.
Explanation. Honeywell A.P.Us recommend 3 continuous start attempts per hour. Boeing
757/767 notes add that a 60 minute cool-down period should be allowed before further start
attempts are made.
>> Question Number. 21. From where does the A.P.U receive a fire signal?
Correct Answer is. It has its own system.
Explanation. The A.P.U compartment has its own fire wires sending a discrete signal to the
A.P.U fire controller.
>> Question Number. 22. What are the two most important signals when monitoring an A.P.U?
Correct Answer is. E.G.T and RPM.
Explanation. E.G.T and RPM are monitored on the A.P.U page of EICAS /ECAM systems.
>> Question Number. 23. One of the accessories driven from the A.P.U gearbox in a centrifugal
switch, the purpose of which is to.
Correct Answer is. Cancel the ignition circuits and arm the overspeed protection circuits.
>> Question Number. 24. What iniates A.P.U shutdown?
78
Correct Answer is. Fire detection, low oil pressure, high oil temperature.
Explanation. Honeywell 331-200 A.P.U handbook refers.
79
15.19, Powerplant Installation.

>> Question Number. 1. Pipes, electrical cables and associated components of a fire-detection
system should be.
Correct Answer is. Fire resistant.
Explanation. Sensors are set to actuate at a temperature below melting point of the detector
and its associated cables.
>> Question Number. 2. The minimum bend radius for a continuous loop type fire wire is.
Correct Answer is. 1 inch.
>> Question Number. 3. Acoustic linings made from composite materials are used in what section
of the engine?
Correct Answer is. Cold section only.
>> Question Number. 4. Vibration mounts are used for.
Correct Answer is. Preventing engine vibration loads being transmitted to the airframe
structure.
Explanation. Small GTE's such as the A.P.U in Boeing 757 and 767 use anti vibration
mounts.
>> Question Number. 5. An aircraft has a heavy landing and on inspection of the engine mounting
bolts the bolts torque loading has reduced, you should.
Correct Answer is. Remove bolt and carry out inspection as the bolt may have increased in
length due to heavy landing.
Explanation. If the bolt has stretched answers a or b will not return the bolts to the original
strength.
>> Question Number. 6. Forward engine mounts take which loads?
Correct Answer is. Thrust, vertical and shear loads.
Explanation. This question is referring to pylon mounted engine mounts.
>> Question Number. 7. Forward engine mounts take which form?
Correct Answer is. Forgings.
Explanation. Forgings are the strongest form of manufacture for substantial structure.
>> Question Number. 8. Pipes around engines are.
Correct Answer is. Stainless steel.
Explanation. Stainless Steel is best for corrosion and heat resistance.
>> Question Number. 9. Fibrous metallic lining for noise suppression is used.
Correct Answer is. In hot area.
>> Question Number. 10. Noise lining in the fan area is made from.
80
Correct Answer is. Porous type Honeycomb and backing sheet.

>> Question Number. 11. A powerplant consists of.
Correct Answer is. The complete engine as it would be found on aircraft including all
connections, controls, cowlings, intake etc.
>> Question Number. 12. Acoustic blankets are installed to.
Correct Answer is. Reduce noise levels.
Explanation. Acoustic blankets are used in both hot and cold sections. The material depends
on the temperature.
>> Question Number. 13. When checking the effect of inertia on the engine after heavy landing
you would first check the.
Correct Answer is. Module alignment.
Explanation. We assume that 'the module' means the powerplant, an initial check will always
be the general visual of the powerplant and its cowlings.
>> Question Number. 14. Following the reports of a heavy landing you would.
Correct Answer is. Carry out a complete visual examination of the power plant.
Explanation. C.A.A.I.Ps Leaflet 6-3 refers to inspection of pylons, mounts and cowlings. As
all of these form part of the Powerplant then answer b is most correct.
>> Question Number. 15. The purpose of spring back and cushion on an engine power lever is.
Correct Answer is. Used when full travel is used but slight movement is still required on the
fuel control unit.
>> Question Number. 16. What are sometimes installed in an engine mounting system to tune
out the worst engine vibrations?
Correct Answer is. Rubber encased wire-mesh vibration isolators.
Explanation. A.P.U's use this sort of engine mount.
>> Question Number. 17. Where are the lifting points on a high bypass turbine engine?
Correct Answer is. On the fan and turbine casing.
Explanation. Assuming this means lifting with a typical bootstrap kit forward and aft mounts
attach to the winches.
>> Question Number. 18. Rubber anti-vibration pads are fitted to engine.
Correct Answer is. Pylons to prevent vibration through the airframe.
Explanation. Quite often used in conjunction with cone bolt mountings.
>> Question Number. 19. Engine thrust is transmitted through mountings that.
Correct Answer is. Allow for radial and axial expansion.
81
>> Question Number. 20. If you reduced the length of bellcrank (2) what would happen to the
input to the F.C.U?
Explanation. Reducing the arm from points 1 to 2 would decrease the arm length from the
centre of rotation on the F.C.U to the connection on the belcrank. This would INCREASE the
amount of rotary movement into the F.C.U.
82
15.20 Fire Protection Systems

>> Question Number. 1. A fire wire is installed.
Correct Answer is. To withstand inertia, vibration, etc., encountered during normal operation.
Explanation. Firewires can be any shape or position, retained in rubber clips.
>> Question Number. 2. Resistive and capacitive type firewires are tested with.
Correct Answer is. Megger/ohmmeter.
>> Question Number. 3. Fire wire clips have rubber in them to.
Correct Answer is. Support the wire.
>> Question Number. 4. Fire extinguishers work by.
Correct Answer is. Combining with remaining oxygen to get rid of it.
>> Question Number. 5. Fire detection systems which are routed through another zone.
Correct Answer is. Must be protected from heat sources in the zone.
Explanation. JAR 25.1203 states that a fire detection device must not pass through another
zone unless it is protected from the heat of that zone.
>> Question Number. 6. The test switch of a continuous loop detector gives a.
Correct Answer is. Continuity check.
>> Question Number. 7. What are the types of continuous fire detection system?
Correct Answer is. Capacitance and resistance.
>> Question Number. 8. What is the operating principle of the spot detector sensor in a fire
detection system?
Correct Answer is. A bimetallic thermoswitch that closes when heated to a high temperature.
>> Question Number. 9. In a fixed fire-extinguishing system, there are two small lines running
from the system and exiting overboard. These line exit ports are covered with a blowout type
indicator disc. Which of the following statements is true?
Correct Answer is. When the yellow indicator disc is missing, it indicates the fire extinguishing
system has been normally discharged.
>> Question Number. 10. Two continuous-loop fire detection systems that will not test due to a
broken detector element are the.
Correct Answer is. Kidde system and the Fenwal system.
>> Question Number. 11. Which of the following fire detection systems measures temperature
rise compared to a reference temperature?
Correct Answer is. Thermocouple.
>> Question Number. 12. A fire involving energized electrical equipment is defined as a.
Correct Answer is. Class C fire.
83
>> Question Number. 13. How are most aircraft turbine engine fire extinguishing systems
activated?
Correct Answer is. Electrically discharged cartridges.
>> Question Number. 14. A fire detection system that operates on the rate of temperature rise is
a.
Correct Answer is. Thermocouple system.
>> Question Number. 15. Why does one type of Fenwal fire detection system use spot detectors
wired in parallel between two separate circuits?
Correct Answer is. So that a single fault may exist in the system without sounding a false
alarm.
>> Question Number. 16. How does carbon dioxide (CO2) extinguish an aircraft engine fire?
Correct Answer is. Contact with the air converts the liquid into snow and gas which smothers
the flame.
>> Question Number. 17. A fuel or oil fire is defined as a.
Correct Answer is. Class B fire.
>> Question Number. 18. Which of the following is the safest fire extinguishing agent to use from
a standpoint of toxicity and corrosion hazards?
Correct Answer is. Bromotrifluoromethane (Halon 1301).
>> Question Number. 19. The explosive cartridge in the discharge valve of a fire extinguisher
container is.
Correct Answer is. A life dated unit.
>> Question Number. 20. A fire detection system operates on the principle of a buildup of gas
pressure within a tube proportional to temperature. Which of the following systems does this
statement define?
Correct Answer is. Lindberg continuous element system.
>> Question Number. 21. The most satisfactory extinguishing agent for an intake fire is.
Correct Answer is. Dry chemical.
>> Question Number. 22. How is the fire extinguishing agent distributed in the engine section?
Correct Answer is. Spray nozzles and perforated tubing.
>> Question Number. 23. What is the principle of operation of the continuous loop fire detector
system sensor?
Correct Answer is. Core resistance material which prevents current flow at normal
temperatures.
84
>> Question Number. 24. The fire detection system that uses a single wire surrounded by a
continuous string of ceramic beads in a tube is the.
Correct Answer is. Fenwal system.
>> Question Number. 25. The fire detection system that uses two wires imbedded in a ceramic
core within a tube is the.
Correct Answer is. Kidde system.
>> Question Number. 26. A continuous loop fire detector is what type of detector?
Correct Answer is. Overheat detector.
>> Question Number. 27. Which of the following fire detection systems will detect a fire when an
element is inoperative but will not test when the test circuit is energized?
Correct Answer is. The Kidde system and the Fenwal system.
>> Question Number. 28. After a fire is extinguished, or overheat condition removed in aircraft
equipped with a Systron- Donner fire detector, the detection system.
Correct Answer is. Automatically resets.
>> Question Number. 29. For fire detection and extinguishing purposes, aircraft powerplant areas
are divided into fire zones based on.
Correct Answer is. Hot and cold sections of the engine.
>> Question Number. 30. What is the function of a fire detection system?
Correct Answer is. To activate a warning device in the event of a powerplant fire.
>> Question Number. 31. What retains the nitrogen charge and fire extinguishing agent in a high
rate of discharge (HRD) container?
Correct Answer is. Breakable disk or fusible disk.
>> Question Number. 32. The use of water on class D fires.
Correct Answer is. Will cause the fire to burn more violently and can cause explosions.
>> Question Number. 33. The pulling out (or down) of an illuminated fire handle in a typical large
jet aircraft fire protection system commonly accomplishes what events?
Correct Answer is. Closes fuel shutoff, closes hydraulic shutoff, disconnects the generator
field, and arms the fire extinguishing system.
>> Question Number. 34. The most satisfactory extinguishing agent for an electrical fire is.
Correct Answer is. Carbon dioxide.
>> Question Number. 35. Which of the following fire detectors are commonly used in the power
section of an engine nacelle?
Correct Answer is. Rate of temperature rise detectors.
85
>> Question Number. 36. Which of the following fire detection systems uses heat in the normal
testing of the system?
Correct Answer is. The thermocouple system and the Lindberg system.
>> Question Number. 37. How are extinguisher spray rings checked for freedom from
obstruction?
Correct Answer is. Blowing through with compressed air.
>> Question Number. 38. What is used as an extinguishant in fire bottles?
Correct Answer is. Halogenated hydrocarbons.
>> Question Number. 39. The advantage of the two shot fire bottle system is.
Correct Answer is. Both bottles can be used in either of the engines.
>> Question Number. 40. To check a fire bottle in situ is serviceable.
Correct Answer is. Check blow out disc, pop up indicators, expiry date and pressure.
Explanation. C.A.I.Ps AL3/10 para 4.3 mentions all these things.
>> Question Number. 41. Resistive type fire-wires are tested using.
Correct Answer is. Megger/ohmmeter.
Explanation. The megger tests insulation the ohmmeter tests continuity.
>> Question Number. 42. When testing an installed fire bottle.
Correct Answer is. A safety ohmmeter is used.
Explanation. Any explosive device requires the use of a safety ohmmeter to limit current flow
through the ignitor.
>> Question Number. 43. On checking a fault free fire detection system.
Correct Answer is. Use a megger only for a short while as it can polarise the element.
Explanation. The fault free or continuous loop firewire is capacitive and resistive. Prolonged
use of the megger could polarise or charge the firewire, to give a false capacitive reading.
>> Question Number. 44. 3 ways to test serviceability of a fixed fire bottle in situ are.
Correct Answer is. Pressure, pop up indicator, blow-out disc.
Explanation. A&P Mechanic Handbook EA-AC-65 Page 401 refers (You can't weigh the
bottle in situ).
>> Question Number. 45. When installing a flow valve on a 'two shot' fire extinguishing system
care must be taken to make sure.
Correct Answer is. Flow arrow should be in a correct direction.
Explanation. Two shot systems do not have any priority. Any flow valve must be fitted in the
right direction which is toward the engine not the bottle!.
>> Question Number. 46. Omission of crushable washer on engine fire-wire connector will.
86
Correct Answer is. Allow moisture ingress.

>> Question Number. 47. Discharge cartridges of the fire bottle have.
Correct Answer is. Life time in hours/or calendar and replace whichever is sooner.
Explanation. Operators usually change cartridges at planned checks. The cartridge also has
a finite manufactures calendar life. This is normally longer.
>> Question Number. 48. The Kidde Fault Free Fire detection system has how many internal
wires in the sensing element?
Correct Answer is. 2.
>> Question Number. 49. When testing a two pin fire bottle connector.
Correct Answer is. Short two pins together.
Explanation. C.A.I.Ps EEL/1-7 para 3.6.4 States that to check for insulation short two pins
together and check for insulation resistance between body and shorted pins from body.
>> Question Number. 50. Gas type fire-wires operate by utilizing.
Correct Answer is. The change in the gas pressure.
Explanation. RR the Jet Engine page 156 Para 16 refers. These gas filled type fire-wires go
by the name of 'Systron Donner'.
>> Question Number. 51. On a fire bottle, if the indicator pin was protruding, this would indicate.
Correct Answer is. Extinguisher had been fired.
Explanation. C.A.I.P's AL/3-10 describes and shows a discharge indicator pin device.
>> Question Number. 52. When testing a squib on a fire bottle, you use a.
Correct Answer is. Low current ohmmeter.
>> Question Number. 53. In a two shot fire extinguishing system.
Correct Answer is. Extinguishers distributed once to either engine compartment.
Explanation. One shot from each bottle to either engine or both shots to one engine.
>> Question Number. 54. Methyl Bromide fire extinguisher are installed with neck.
Correct Answer is. At the top.
Explanation. The heavier fluid is pushed out of the bottle by the head of gas sitting above
the liquid.
>> Question Number. 55. In a Fenwall fire detection system.
Correct Answer is. The tube is inconel and wire is nickel.
>> Question Number. 56. When a fire extinguisher is discharged the immediate action is.
Correct Answer is. clean with hot water.
Explanation. When the extinguishant is introduced into the gas path hot water should be
used.
87
15.21, Engine Monitoring and Ground Operation.

>> Question Number. 1. Who establishes the recommended operating time between overhauls
(T.B.O) of a gas turbine engine.
Correct Answer is. The operator (utilizing manufacturer data and trend analysis) working in
conjunction with the Airworthiness Authority.
>> Question Number. 2. What is the first engine instrument indication of a successful start of a
turbine engine?
Correct Answer is. A rise in the exhaust gas temperature.
>> Question Number. 3. A hung start is indicated by the.
Correct Answer is. Fails to reach idle RPM.
>> Question Number. 4. The blending of blades and vanes in a turbine engine.
Correct Answer is. No Answer.
>> Question Number. 5. During inspection, turbine engine components exposed to high
temperatures may only be marked with such materials as allowed by the manufacturer. These
materials generally include.
Correct Answer is. Layout dye, commercial felt tip marker or chalk.
>> Question Number. 6. When the leading edge of a first stage turbine blade is found to have
stress rupture cracks, which of the following should be suspected?
Correct Answer is. Over temperature condition.
>> Question Number. 7. A magnetic chip detector inspection should be carried out.
Correct Answer is. Within a specified time from shut down.
Explanation. A.L.F 502 and 507 engines on 146/R.J specify that the engine M.C.D be
checked after 20mins but before 2 hrs since shut down.
>> Question Number. 8. What is the proper starting sequence for a turbojet engine?
Correct Answer is. Starter, ignition, fuel.
>> Question Number. 9. Foreign object damage on a compressor, when boroscoping, is indicated
by.
Correct Answer is. Nicks and scores.
>> Question Number. 10. Turbine blades are generally more susceptible to operating damage
than compressor blades because of.
Correct Answer is. Higher temperature stresses.
>> Question Number. 11. A magnetic chip detector detects.
Correct Answer is. Ferrous particles only.
>> Question Number. 12. A cool-off period prior to shutdown of a turbine engine is done to.
88
Correct Answer is. Allow the turbine wheel to cool before the case contracts around it.
>> Question Number. 13. When starting a turbine engine, the starter should be disengaged.
Correct Answer is. After the engine has reached self-sustaining speed.
>> Question Number. 14. What should be done initially if a turbine engine catches fire when
starting?
Correct Answer is. Turn off the fuel and continue engine rotation with the starter.
>> Question Number. 15. A turbine engine hot section is particularly susceptible to which kind of
damage?
Correct Answer is. Cracking.
>> Question Number. 16. If a turbine engine is unable to reach takeoff E.P.R before its E.G.T
limit is reached, this is an indication that the.
Correct Answer is. Compressor may be contaminated or damaged.
>> Question Number. 17. Which of the following engine variables is the most critical during
turbine engine operation?
>> Question Number. 18. With the engine running at idle, the E.P.R system reads just over 1.
Correct Answer is. This is a normal condition and does not need attention.
Explanation. E.P.R with the engine shut down should read 1. At idle a very small pressure
increase occurs in the jet pipe.
>> Question Number. 19. The recurrent ingestion of dust or other fine airborne particulates into
an engine can result in.
Correct Answer is. Erosion damage to the compressor and turbine sections.
>> Question Number. 20. When the engine is not running, and engine blanks are installed. The
E.P.R gauge shows 1.0, then.
Correct Answer is. It is normal.
>> Question Number. 21. Which of the following may be used to accomplish internal inspection
of an assembled gas turbine engine?
Correct Answer is. X-ray and a borescope.
>> Question Number. 22. Run down time is indicative of.
Correct Answer is. The freedom of rotation of the compressor.
Explanation. Short run down time is indicative of bearing failure.
>> Question Number. 23. A hung start or false start is one in which.
Correct Answer is. Light up' occurs, but the RPM does not increase.
89
>> Question Number. 24. What would be the possible cause if a gas turbine engine has high
exhaust gas temperature, high fuel flow, and low RPM at all engine power settings?
Correct Answer is. Turbine damage or loss of turbine efficiency.
>> Question Number. 25. In regard to using a turbine engine oil analysis program, which of the
following is NOT true?
Correct Answer is. Generally, an accurate trend forecast may be made after an engine's first
oil sample analysis.
>> Question Number. 26. Which of the following is the least likely indication of a main bearing
failure?
Correct Answer is. High oil pressure.
Explanation. Low oil pressure would indicate bearing failure not High.
>> Question Number. 27. After shutdown, flames are present in the exhaust pipe. The probable
cause is.
Correct Answer is. A defective pressurizing and dump valve.
>> Question Number. 28. If the L.P cock is used to shut down an engine.
Correct Answer is. The H.P fuel pump will run dry.
Explanation. The L.P cock is normally aircraft mounted. The engine will run until the H.P fuel
pump runs dry.
>> Question Number. 29. When accelerating from 'light-up' to ground idling speed, the E.G.T will.
Correct Answer is. Increase above idle value then decrease to normal.
Explanation. All Gas Turbines tend to overfuel until the RPM increases sufficiently to supply
correct idle air flow.
>> Question Number. 30. A gas turbine engine is stopped by closing.
Correct Answer is. H.P cock.
>> Question Number. 31. A 'wet start' is indicated by.
Correct Answer is. No temperature indication.
Explanation. Due to lack of ignition.
>> Question Number. 32. The engine accelerates to idling by.
Correct Answer is. Combined efforts of starter motor and gas flow.
>> Question Number. 33. An oil emission spectrometer measures.
Correct Answer is. Particles in suspension.
Explanation. The colour of the spectrum produced upon burning the oil indicates parts per
million of all metallic elements contained in the sample.
>> Question Number. 34. A broadband vibration reading indicates.
90
Correct Answer is. The total vibration sensed by the transducer.

Explanation. Broadband is the total of all the vibrations sensed.
>> Question Number. 35. Vibration analysers determine which component is vibrating by
analysing.
Explanation. The faster the compressor shafts rotate the higher the frequency.
>> Question Number. 36. High frequency vibration.
Correct Answer is. Causes engine components to crack.
Explanation. The more vibration cycles the nearer to failure the component will become.
>> Question Number. 37. Engine oil sampling analysis is taken.
Correct Answer is. At specific time after engine shut down.
>> Question Number. 38. With external power applied, the engine will not run up to idle after
reaching starting speed. The likely fault would be with the.
Correct Answer is. Fuel Control Unit.
Explanation. Once an engine has reached starter cut out speed the only thing that can stop
it accelerating is underfuelling.
>> Question Number. 39. When running down an engine.
Correct Answer is. It should be done as slowly as possible to reduce thermal stress.
>> Question Number. 40. What may be an indication of a bleed valve stuck in the closed position?
Correct Answer is. Compressor stalling at low RPM.
Explanation. A closed bleed valve at low RPM means the compressor has too much air to
handle, hence it may stall or surge.
>> Question Number. 41. Excessive E.G.T can.
Correct Answer is. Cause damage to turbine.
Explanation. The turbine is the highest stressed component in the engine.
>> Question Number. 42. A jet engine has a high oil temperature but all other power parameters
are normal. The probable cause is.
Correct Answer is. A main bearing in distress.
Explanation. Oil systems cool as well as lubricate.
>> Question Number. 43. When cleaning salt from a compressor.
Correct Answer is. Use water at low power then water at high power.
>> Question Number. 44. A hot start refers to.
Correct Answer is. High E.G.T before idle RPM is achieved.
91
Explanation. A hot start is defined as an overtemping of the engine as the engine starts. It
may be caused by overfuelling, but not necessarily.
>> Question Number. 45. If a compressor surge occurs, it is recognized by.
Correct Answer is. Coughing in the compressor and vibration.
Explanation. Whilst E.G.T and RPM will fluctuate, fuel flow will not and thrust cannot be
measured. Therefore coughing and vibration is the correct answer.
>> Question Number. 46. Cracks may occur in hot section components of a turbine engine if they
are marked during inspection with.
Correct Answer is. A lead pencil.
Explanation. Graphite based markers can cause intergranular corrosion.
>> Question Number. 47. What must not be used during an engine compressor wash?
Correct Answer is. Chlorine.
Explanation. By elimination b is correct. Crushed almond and desalination solutions are
accepted compressor wash applications.
>> Question Number. 48. Trend monitoring of spectrometric oil analysis is carried out how often?
Correct Answer is. At set periods once the rate of wear has been established.
Explanation. New components always wear more than when they are run in. SOAP
monitoring periods depend on the component not on the aircraft servicing cycle.
>> Question Number. 49. Starting an engine with a bleed valve stuck closed would cause:.
Correct Answer is. Possible stalling of the engine.
Explanation. Bleed valves are normally open on start to prevent stalling.
>> Question Number. 50. Galling is a condition caused by excessive.
Correct Answer is. Chafing.
Explanation. See Dale Crane - Dictionary of Aircraft Terms.
>> Question Number. 51. If a burner was down, in a multi-can system, the engine would tend to.
Correct Answer is. Surge.
Explanation. If a combustor tube fails to ignite there will be a pressure build up at the
entrance to that burner can.
>> Question Number. 52. If the rundown time is less than the minimum stated for a given engine.
Correct Answer is. The rotating assembly is being restricted.
Explanation. Failure to allow the engine to stabilise at idle after high power runs may cause
the rotor to rub on the casing in older engines.
>> Question Number. 53. When running an engine the following lights should be on:.
Correct Answer is. Anti-collision and nav-lights (if fitted).
92
Explanation. An anti-collision light is always fitted and turned on for ground running. If there
are nav lights it makes sense to have them on as well.
>> Question Number. 54. With spectral oil analysis program (S.O.A.P), samples are taken.
Correct Answer is. At a specified interval.
Explanation. SOAP samples are taken at routine servicing intervals as part of a preventative
maintenance system.
>> Question Number. 55. During start, if a bleed valve is stuck closed.
Correct Answer is. E.G.T will be lower than normal.
Explanation. More air is passing through the engine than it should therefore it will be cooler.
>> Question Number. 56. Dynamic balance testing locates unbalance in.
Correct Answer is. Two planes.
Explanation. Dynamic balance is caused when the masses that are rotating are not equal
and when the component parts, for example, propeller blades, are not tracking in the same plane.
>> Question Number. 57. On a gas turbine engine with baked oil deposits, how would you carry
out grit blast cleaning with the engine at?
Correct Answer is. Idle speed (low).
Explanation. Compressor cleaning is done with the engine running using a variety if grits in
a water solution.
>> Question Number. 58. A rotation pad on an accessory drive gear box is provided for.
Correct Answer is. N2 rotation.
Explanation. The rotation of the H.P compressor is required during borescope inspection.
>> Question Number. 59. What would be indicative of a hung start?
Correct Answer is. Engine would fail to reach self-sustaining speed.
Explanation. In a hung start the engine normally stagnates at or near the starter cut out and
any attempt to accelerate the engine will result in a hot start.
93
15.22, Engine Storage and Preservation.

>> Question Number. 1. Fuel system inhibiting oil is.
Correct Answer is. Mineral oil.
Explanation. C.A.I.Ps EL/3-14 refers to mineral oil.
>> Question Number. 2. After placing an engine in an M.V.P envelope.
Correct Answer is. Check humidity indicator after 24 hours.
Explanation. Old C.A.I.Ps leaflet EL/3-14 refers.
>> Question Number. 3. On a vapour proof cocoon, there is a.
Correct Answer is. Moisture indicator.
Explanation. C.A.I.Ps EL/3-14 refers.
>> Question Number. 4. When an installed engine is not to be used for a period of up to 7 days.
Correct Answer is. It is only necessary to blank off all apertures.
Explanation. C.A.I.Ps EL/3-14.
>> Question Number. 5. Installed engines must be re-preserved after preservation at least every.
Correct Answer is. Six months.
Explanation. C.A.I.Ps EL/3-14.
>> Question Number. 6. On storage of an engine, the desiccant is.
Correct Answer is. Looked at 24 hrs later if its blue it’s OK.
Explanation. C.A.I.P's EL/3-14 (Engine Storage) refers. Note that answer a is partly correct,
but you must also inspect the MVP envelope for damage or deterioration.
>> Question Number. 7. After placing an engine into storage, details would be recorded in.
Correct Answer is. Engine log book.
Explanation. All engines have a log book.
>> Question Number. 8. When storing an engine the fuel system is to be inhibited. How is this
done?
Correct Answer is. Remove plugs rotate engine then add oil.
Explanation. C.A.I.P's EL 3-14 (Engine storage) refers. This is a piston engine question but
has been reported as being in a module 15 exam.
>> Question Number. 9. An engine in storage for 7 days should.
Correct Answer is. Be fitted with covers and blanks and apertures covered.
Explanation. Old C.A.I.P's EL/3-4 refers.
>> Question Number. 10. On a (VP) cocoon bag, if the humidity indicator turns pink/lilac.
Correct Answer is. Desiccant is ineffective and needs changing.
Explanation. C.A.I.P's EL/3-4 refers.
94
>> Question Number. 11. To inhibit the fuel system of an installed engine.
Correct Answer is. Dry motor the engine.
Explanation. C.A.I.P's EL 3-10 details this procedure. It is done by dry motoring the engine
with a header tank of inhibiting oil connected to the inlet of the L.P fuel pump.
>> Question Number. 12. When is the humidity indicator checked on a preserved engine?
Correct Answer is. 1 Month.
Explanation. C.A.A.I.Ps leaflet 7-4 states 'approximately monthly intervals'. If the desiccant
is pink the envelope must be opened, the desiccant replaced and the envelope resealed.
>> Question Number. 13. With an engine in storage, desiccant is used.
Correct Answer is. To remove moisture from the air.
Explanation. A&C Mechanics Handbook EA-AC65 page 389 refers.
>> Question Number. 14. Small cuts in a M.V.P. engine storage bag can be repaired.
Correct Answer is. With adhesive PVC tape.
>> Question Number. 15. When removing an engine for long-term storage, bleed valves should
be.
Correct Answer is. Open but blanked.
95
15.23. MISC
>> Question Number. 1. The types of water present in aviation fuel are.
Correct Answer is. Free and entrained both harmful.
>> Question Number. 2. Oil pressure and scavenge pumps are usually.
Correct Answer is. Spur gear pumps.
>> Question Number. 3. The purpose of a pressure filter in a lubrication system is to.
Correct Answer is. Protect the oil jets.
>> Question Number. 4. A curvic coupling.
Correct Answer is. Accurately aligns the driving and the driven shafts.
>> Question Number. 5. Feeders are.
Correct Answer is. Heavy duty electrical generator cables.
>> Question Number. 6. High air humidity will.
Correct Answer is. Reduce the thrust output.
>> Question Number. 7. C.I.T sensor is made up of.
Correct Answer is. Platinum-rhodium.
>> Question Number. 8. What is the maximum value of pressure with reference to a jet engine?
Correct Answer is. 1 Atmospheric Pressure.
Explanation. 1 Atm. = 1.013 Bar.
>> Question Number. 9. The hottest casing is the.
Correct Answer is. H.PT.
>> Question Number. 10. Centrifugal compressor maximum tip speed is.
Correct Answer is. 1.2 Mach.
>> Question Number. 11. What type of oil is used in a gas turbine engine?
Correct Answer is. Synthetic.
96

Module 15 Question Bank

Uploaded by

Copyright:

Available Formats

Module 15 Question Bank

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Module 15 Question Bank

Uploaded by

Copyright:

Available Formats

EASA PART 66 QUESTION BANK

MODULE 15: GAS TURBINE ENGINE

All the Best wishes for aspirant readers.

SUGGESTED STUDY MATERIALS

Book Title Author ISBN

Ref: CAAB ANO Part 66 Guidance Material

15.1 GAS TURBINE ENGINE Fundamentals.

Correct Answer is. Effective perceived noise decibels (E P N dB).

Correct Answer is. LP turbine.

15.2 ENGINE PERFORMANCE.

Correct Answer is. Turbine inlet guide vanes.

>> Question Number. 36. Thrust will.

Correct Answer is. Velocity increases and pressure decreases.

15.3 Engine Inlet

Correct Answer is. Continuously and intermittently.

15.4 Engine Compressors.

>> Question Number. 25. Compression occurs.

15.5 Combustion Section.

>> Question Number. 6. The air used for combustion is.

15.6 Turbine Section.

Correct Answer is. Over-temp with excessive centrifugal loads.

Correct Answer is. 90% - 95%.

15.7 Engine Exhaust.

Correct Answer is. Exit velocity lower causing loss of thrust.

15.8 Bearings and Seals.

15.9 Lubricants and Fuels.

>> Question Number. 25. Ignition of fuel depends upon.

15.10 Lubrication Systems.

Correct Answer is. Increases fuel temperature.

Correct Answer is. By splashed or sprayed oil.

15.11 Fuel Systems.

>> Question Number. 28. On a FADEC engine, the channel reset.

Correct Answer is. 40 degrees.

Correct Answer is. Fuel pressure to both engine pumps.

15.12 Air Systems.

15.13, Starting and Ignition Systems.

15.14, Engine Indication Systems.

Correct Answer is. Noticeable shift in E.P.R.

Correct Answer is. Frequency output is proportional to engine speed.

>> Question Number. 59. A ballast resistor is fitted.

15.15, Power Augmentation Systems

>> Question Number. 14. Water/methanol is injected.

15.16, Turbo-prop Engines

15.17, Turbo-Shaft Engines.

15.18, Auxiliary Power Units (APUs).

15.19, Powerplant Installation.

Correct Answer is. Porous type Honeycomb and backing sheet.

15.20 Fire Protection Systems

Correct Answer is. Allow moisture ingress.

15.21, Engine Monitoring and Ground Operation.

Correct Answer is. The total vibration sensed by the transducer.

15.22, Engine Storage and Preservation.

You might also like