PRT Lecture - 16 17

Petroleum Refining Technology
(CHE F422)
Distillation of Petroleum
• Separation technique
• Boiling range: -160 ° C to 1000 °C
• Methane: -160 °C
• Pitch: above 1000 °C
• Mixture of gas, liquid, & solid.

• Effective and economic distillation to process no. of
cut of smaller boiling range.
• Cuts later processed to suitable as per consumer
requirement.
• Fraction in demand depends upon country
• USA: more gasoline production
• India: more distillate
BITS Pilani, Hyderabad Campus

Refinery distillation
• Based on TBP tests

• Distillation
• Atmospheric distillation unit (ADU): Atmospheric pressure
• Vacuum distillation unit (VDU): Reduced pressure
• Maximum temperature on topping operation: 375 °C.
• High temperature not permitted due to degradation of crude
by thermal cracking.
• Soluble gases
• Preflashing: 100 C & 3-5 atm.
• To avoid load on ADU
• Transport of crude for long distance
• 6% light end (gases): no problem for transportation of crude.

Arrangement of tower
Three types of arrangements: ( How heat is removed)

1. Top Tray Reflux:
2. Pump back Reflux:
3. Pump Around Reflux:

Top Tray Reflux
Reflux is only at top tray only
• Reflux is cooled and sent into the Tower.
• Heat input: Through Tower bottom.
• Removal: at the top.
• Thus requires large tower diameter.
• Improper reflux and poor quality of
fraction. Economic utilization of heat is not
possible.

Pump back Reflux
• Reflux is provided at regular

intervals.
• This helps every plate to act as a

true fractionator.( because there is
always good amount of liquid).
• Tower is uniformly loaded, hence

uniform and lesser diameter tower
will do.
• Heat from external reflux can be

utilized as it is at progressively
higher temperatures.
Most common in refineries
• However design of such tower is
costly, but provides excellent
service.
Pump Around Reflux
• In this arrangement reflux from a

lower plate is taken, cooled and
fed into the column at a higher
section by 2 to 3 plates.
• This creates local problem of

mixing uneven composition of
reflux and liquids present on the
tray.
• Designers treat all the plate in this

zone as one single plate, the result
gives large number of plates and
high tower height.

Design aspects
Separation Criteria
• DEGREE OF SEPARATION: Difference between ASTM- 5% of heavier
distillate and ASTM -95% point of lighter distillate.
• Defined in terms of product purities or component recoveries.
• Greater the degree of separation, greater will be recovery of the light component in
the distillate and the heavy component in bottoms.
• DEGREE OF DIFFICULTY OF SEPARATION: Difference between

ASTM 50% point of the distillate fraction in questions.
• Defined as the relative difficulty encountered in separating the two compounds,
regardless the purity requirements set by process specifications~ inversely
proportional to the relative volatility between the two components.

ASTM Gap and Overlap
• Fractionation is the difference between 5% ASTM curve of Heavy cut and

the 95 % point on the ASTM curve of a lighter cut of two adjacent side
product.
• Positive difference is called Gap.
• Negative difference is called overlap.
• ASTM Boiling range gives general composition of fractions.
• 5- 95 GAP: Defines the relative degree of separation between adjacent

fractions.
• Determined by subtracting 95 vol.% ASTM Temperature of a fraction

from the 5 Vol. % ASTM temperature of the adjacent heavy fraction.
General observation for separation
For a given system
• No. of trays required increases markedly as purity requirement
increases, but reflux requirements increases only a small amount.
• Tray and reflux requirements increases as relative volatility

decreases i.e separation becomes more difficult.
Separation Criteria
• For a fixed number of trays, reflux requirement is directly
proportional to the degree of difficulty of separation.
Qualitatively
At reflux condition exceeding minimum requirements =>Tray
requirements are directly proportional to the required degree of
separation.
•The degree of difficulty of separation inherent in the physical chemical
system under consideration.
Crude Column Design
INPUT REQUIRED
• Crude TBP (essential)
• Density/API gravity (essential)
• Molecular Weight(optional)
• Viscosity(optional)
SPECIFICATION REQUIRED
• Column Pressure
• Product specification can be given in terms of fix draw or distillation point.
• Pump around duties need to be specified.
• Column top temperature can be specified.
Process design
• Prepare TBP Distillation and equilibrium Flash Vaporisation curves of crude
to be processed.
• Using crude assay data construct TBP curves for all products except gas and
reduced crude. Convert these to ASTM & EFV.
• Convert TBP data to EFV curves.
• Prepare material balance of crude distillation column, on both volume and
weight basis.
Packie’s Method
• Degree of difficulty of separation : The difference between 50 vol.% temperatures of the
fractions under study.
• Convert 50% TBP temp to ASTM.
• Separation Capability (F): It is defined as the product of the reflux to feed ratio at the
upper draw tray as calculated on the volumetric basis and the number of actual trays in
that section.(F, Factor related to gap and overlap).
• Packie method: Based on Gap and overlap.
• Number of plates in particular section depends on gap and reflux ratio.
• F= Reflux ratio x Number of plates in that section.
F=(LN/DN)NT,(NT: No of trays of distillation column)

L/D= Reflux ratio
TBP, ASTM, and EFV curves for a middle distillate fraction crude oil
• TBP, ASTM, and EFV: achieve different level of separation for a given sample.
• Significant difference in IBP and EP for a middle distillate.
• All curves converge near 50% volume distillate.
• TBP: Crude characterization
• ASTM: Usually used for refinery products & property correlation and calculation.
• EFV: Provide useful data for flashing operations
TBP VS ASTM 50% B.P
IBP AND FBP OF ASTM & TBP
Relation Between IBP and FBP of ASTM and TBP
Problem: In a refinery side stream operation the fraction to be collected is diesel.
The diesel entering the side stripper is 4000 bbl/h, the 50 percent point of the cut is
275 oC and contained with Kerosene whose mid boiling point is 145 oC. If the stripper
is having 4 plates find the actual amount of diesel coming out of the stripper if the
ASTM GAP is 20 o C.
SOLUTION:
Calculate F Factor from Packie method for side
stream stripper.
ASTM ΔT50%= 275- 145= 130oC (254 oF)ASTM GAP=
20 oC = 36 oF
F= (L/D)NT=>L/D= 5/4= 1.25
V= L+D = 4000
Hence D( Actual amount of diesel )= 1778 bbl.
Calculation of minimum number of stage
Fenske equation is used for Nm
Calculation of minimum reflux ratio

Using Underwood Equation:
Distillation Column Design
• Specify the degree of separation:- Set product

specification.
• Select the operating conditions:- Operating pressure.
• Determine the stage and reflux requirement:- The number

of equilibrium stages.
• Select type of contacting device:- Plates or packing.
• Size the column:- Diameter, number of real stages.
• Design the column internals:- Plates, Distributors, Packing

Supports etc.
• Mechanical design:- Vessel and Internal fittings.

Some basis
• Section above feed point-Rectifying/Enrichment

Section
• Section below Feed-Stripping Section
• Reflux ratio R= Flow returned as reflux/Flow of top

product design
• Minimum reflux Rmin:-Reflux below which stage

required is infinity.
• Optimum reflux ratio typically lines between 1.2 to

1.5 times the minimum reflux ratio.
• Relative Volatility αij=Pi/Pj=Ki/Kj
• y=αX/(1+(α-1)x) for construction of y-x diagram.

Some basis
• MESH EQUATION i:e Material Equilibrium,

Summation and Heat (Energy)Balance
Equation.
• MESH Equation can be written for each
stage and for reboiler and condenser.
• The Solution of the set of equations forms
the basis of rigorous methods.
Basic Processes
• Separation by Boiling point difference.
• Crude Assay provides estimates of various products
obtainable from a particular crude.

Atmospheric Distillation Unit
• First unit in the refining process for separation of crude into various
fractions by atmospheric distillation.
• Fractions have specific BP ranges & relative volatility.
• After desalting, the crude oil is preheated to ~ 290°C by heat exchange

with product and reflux streams.
• It is then further heated to ~ 340-380°C in a furnace and charged to the

flash zone of the ADU.
• ADU, a steel cylinder ~ 35-60 m height.
• Bubble-cap/ valve-trays/ sieve plate type are used.

Vacuum Distillation Unit
• In VDU, P is reduced to
prevent thermal cracking
to obtain more distillate
from RCO.
• VDU is larger-diameter
(8-12m) columns to
maintain vapor velocity
at reduced pressure.
• Temp in flash zone

450°C & absolute P is
~40 mmHg.
• Number of side cuts are
limited to three or four.
• Operation of VDU is costly than ADU.
• Amount of steam demand depends on the extent of

vacuum.
• Role of tray, plates.

• Least pressure drop well preferred.
• Steam with vacuum separates fractions with a good
economy rather than alone.
• Most of the tower operates at 30-40 mm Hg.
• Top pressure 20-25 mm Hg.
• Number of side cuts are limited to three or four.

Operating data
• Temperature in flash zone: 350-400 °C.
• Pressure in flash zone: 30-40 mm Hg.
• Pressure for long residue: 40-60 mm Hg.
• Top pressure: 12-15 mm Hg.
• Temperature at top: 225-250 °C.
• Steam (370 °C) rate: 0.3 to 5 kg per barrel

PRT Lecture - 16 17

Uploaded by

Copyright:

Available Formats

PRT Lecture - 16 17

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PRT Lecture - 16 17

Uploaded by

Copyright:

Available Formats

Petroleum Refining Technology

• Mixture of gas, liquid, & solid.

BITS Pilani, Hyderabad Campus

• Based on TBP tests

• 6% light end (gases): no problem for transportation of crude.

BITS Pilani, Hyderabad Campus

Three types of arrangements: ( How heat is removed)

BITS Pilani, Hyderabad Campus

BITS Pilani, Hyderabad Campus

• Reflux is provided at regular

• This helps every plate to act as a

• Tower is uniformly loaded, hence

• Heat from external reflux can be

• In this arrangement reflux from a

• This creates local problem of

• Designers treat all the plate in this

BITS Pilani, Hyderabad Campus

• DEGREE OF DIFFICULTY OF SEPARATION: Difference between

BITS Pilani, Hyderabad Campus

• Fractionation is the difference between 5% ASTM curve of Heavy cut and

• Positive difference is called Gap.

• Negative difference is called overlap.

• ASTM Boiling range gives general composition of fractions.

• 5- 95 GAP: Defines the relative degree of separation between adjacent

• Determined by subtracting 95 vol.% ASTM Temperature of a fraction

• Tray and reflux requirements increases as relative volatility

F=(LN/DN)NT,(NT: No of trays of distillation column)

Fenske equation is used for Nm

Calculation of minimum reflux ratio

• Specify the degree of separation:- Set product

• Select the operating conditions:- Operating pressure.

• Determine the stage and reflux requirement:- The number

• Select type of contacting device:- Plates or packing.

• Size the column:- Diameter, number of real stages.

• Design the column internals:- Plates, Distributors, Packing

• Mechanical design:- Vessel and Internal fittings.

BITS Pilani, Hyderabad Campus

• Section above feed point-Rectifying/Enrichment

• Section below Feed-Stripping Section

• Reflux ratio R= Flow returned as reflux/Flow of top

• Minimum reflux Rmin:-Reflux below which stage

• Optimum reflux ratio typically lines between 1.2 to

• Relative Volatility αij=Pi/Pj=Ki/Kj

• y=αX/(1+(α-1)x) for construction of y-x diagram.

BITS Pilani, Hyderabad Campus

• MESH EQUATION i:e Material Equilibrium,

BITS Pilani, Hyderabad Campus

• Fractions have specific BP ranges & relative volatility.

• After desalting, the crude oil is preheated to ~ 290°C by heat exchange

• It is then further heated to ~ 340-380°C in a furnace and charged to the

• ADU, a steel cylinder ~ 35-60 m height.

• Bubble-cap/ valve-trays/ sieve plate type are used.

• Temp in flash zone

• Amount of steam demand depends on the extent of

• Role of tray, plates.

• Most of the tower operates at 30-40 mm Hg.

• Top pressure 20-25 mm Hg.

• Number of side cuts are limited to three or four.

You might also like