GR-1600XL (Left-hand drive)

160 Ton (145 Metric Ton) Capacity

SPEC. SHEET NO. GR-1600-3-00104/ES-01

HYDRAULIC ROUGH TERRAIN CRANE

DIMENSIONS

(φ1'10-1/2")
570
OPTIONAL WEIGHT 11.1 t (24,500 lbs)
3,500 (11'5-3/4") 4,165 (13'8") 4,860 (15'11-1/8")

7,300 (23'11-3/8")
8,200 (26'10-7/8")
2,990 (9'9-3/4")
5,500 (18'1/2")
4,520 (14'10") 4,505 (14'9-1/4")
4,6
00
(15
'1"
)

13,050–61,000 (42'9-3/4"–200'1-1/2")
2,400 (7'10-3/8")

3,785 (12'5")
17.4º

16.2º
12.6º

11.9º

2,599 (8'6-1/4") 2,010 (6'7-1/8") 1,100 (3'7-1/4")

3,315 (10'10-1/2") 10,155 (33'3-3/4")
8,045 (26'4-7/8") 4,000 (13'1-1/2") 2,000 (6'6-3/4") 2,145 (7'1/4")
16,190 (53'1-3/8")

Note : Dimension is with boom angle at -1.5 degree.

GENERAL DIMENSIONS
Meter Feet Meter Feet
Turning radius (26.5R25☆☆ Tires) Overall length approx. 16,190 53' 1-3/8"
6 wheel steer 9.9 32' 6" Overall width approx. 3,315 10'10-1/2"
2 wheel steer 14.9 48'11" Overall height approx. 3,785 12' 5"
Carrier length approx. 8,260 27' 1-1/4"
for traveling

Specifications are subject to change without notice.

 SPEC. SHEET NO. GR-1600-3-00104/ES-01

BOOM AUXILIARY WINCH

6 sections boom of round box construction with 7 sheaves at Variable speed type with grooved drum driven by hydraulic axial
boom head, extended by single telescoping cylinder. piston motor through speed reducer.
2 easily removable wire rope guards, rope dead end provided on Power load lowering and raising. Equipped with automatic brake
both sides of boom head. Boom telescope sections are (neutral brake) and counterbalance valve. Controlled
supported by wear pads both vertically and horizontally. independently of main winch. Equipped with cable follower and
Fully retracted length....... 13.1 m (42.8') drum rotation indicator.
Fully extended length ...... 61.0 m (200.1')
Extension speed.............. 47.9 m (157.3') in 450 s AUXILIARY DRUM
Sheave root diameter ...... 0.400 m (15-3/4") Root diameter x wide ............. 0.382 m (15") x 0.742 m (29-1/4")
Wire rope diameter x length ........... 19 mm (3/4") x 225 m (738')
BOOM ELEVATION Drum capacity ........................................ 394 m (1293'), 7 layers
By a double acting hydraulic cylinder with holding valve. Maximum single line pull (1st layer).............9,900 kg (21,800 lbs)
Boom angle indicator. Maximum permissible linepull wire strength...7,200 kg (15,900 lbs)
Automatic speed reduction and slow stop function.
Boom angle ..................... -1.5–81.5º WIRE ROPE
Boom raising speed ........ 20º to 60º in 28 s Non-rotating 19 mm (3/4") 7x35 class.
Breaking Strength 36,000 kg (79,400 lbs)
JIB
2 stage bi-fold lattice type, offset angle (5–40º) by tilt cylinder. HOOK BLOCKS
Single sheave at the head of both jib sections. Stowed alongside 100 metric ton (110 ton, option) .... 7 sheaves with hook block and
base boom section. Assistant cylinders for mounting and stowing, safety latch.
controlled at right side of superstructure. 45 metric ton (50 ton, option) ........ 3 sheaves with hook block and
Self stowing jib mounting pins. safety latch.
Length ............................. 10.3 m, 18.0 m (33.8', 59.1') 7.2 metric ton (7.9 ton, option) ...... Weighted hook with swivel and
Offset............................... 5–40˚ safety latch.
Sheave root diameter ...... 0.440 m (17-5/16")
HYDRAULIC SYSTEM
INSERT JIB (OPTION) PUMPS
Insert lattice jib can be used for reaching higher place. 2 variable piston pumps for crane functions.
Length .................. 7.0 m (1 pce.), 14.0 m (2 pcs.), (23.0', 45.9') Tandem gear pump for steering, swing and optional equipment.
Powered by carrier engine. Pump disconnect for crane is
SHORT JIB (OPTION) engaged/ disengaged by rotary switch from operator's cab.
2 sheaves, heavy lifting jib can be used for lifting lifting heavy load
in tight spaces. CONTROL VALVES
Length ............................ 3.6 m (11.8') Multiple valves actuated by pilot
Offset.............................. 20º, 40º pressure with integral pressure relief valves.
Sheave root diameter ..... 0.419 m (16-1/2")
RESERVOIR
AUXILIARY LIFTING SHEAVE (SINGLE TOP) 763 lit. (202 gallon) capacity. External sight level gauge.
Single sheave, mounted to main boom head for single line work
(stowable). FILTRATION
Root diameter.................. 0.440 m (17-5/16") BETA10=10 return filter, full flow with bypass protection, located
inside of hydraulic reservoir. Accessible for easy replacement.
ANTI-TWO BLOCK DEVICE
Pendant type over-winding cut out device with audio-visual OIL COOLER
(FAILURE lamp/BUZZER) warning system. Air cooled fan type.
SLEWING CAB AND CONTROLS
Hydraulic axial piston motor driven through planetary slewing Both crane and drive operations can be performed from one
speed reducer. Continuous 360º full circle slewing on ball bearing cab mounted on rotating superstructure.
turn table at 1.3min-1 {rpm}. Equipped with manually
locked/released slewing brake. A 360º positive swing lock 15º tilt, Left side, 1 man type, steel construction with sliding door
manually engaged in cab. Twin slewing system: Free slewing or access and safety glass windows opening at side. Door window is
lock slewing controlled by selector switch on front console. powered control. Windshield glass window and roof glass window
Slewing speed ................. 1.3 min-1 {rpm} are shatter-resistant. Tilt-telescoping steering wheel. Adjustable
control lever stands for swing, boom elevating, boom telescoping,
COUNTERWEIGHT auxiliary winch and main winch. Control lever stands can change
Standard weight ...................18,200 kg (40,100 lbs) neutral positions and tilt for easy access to cab. 3 way adjustable
Extra weight right (option) ..... 5,550 kg (12,250 lbs) operator's seat with high back, headrest and armrest. Engine
Extra weight left (option)........ 5,550 kg (12,250 lbs) throttle knob. Foot operated controls: boom elevating boom
telescoping, service brake and engine throttle. Hot water cab
WINCH heater and air conditioning.
MAIN WINCH
Variable speed type with grooved drum driven by hydraulic axial Dash-mounted engine start/stop, monitor lamps, cigarette
piston motor through speed reducer. Power load lowering and lighter, drive selector switch, parking brake switch, steering mode
raising. Equipped with automatic brake (neutral brake) and select switch, power window switch, pump engaged/ disengaged
counterbalance valve. Controlled independently of auxiliary winch. switch, swing brake switch, telescoping/auxiliary winch select
Equipped with cable follower and drum rotation indicator. switch, outrigger controls, free swing / lock swing selector switch,
eco mode switch, high speed winch (main/aux) switch and
MAIN DRUM ashtray.
Root diameter x wide ............. 0.382 m (15") x 0.742 m (29-1/4")
Wire rope diameter x length ........ 19 mm (3/4") x 320 m (1,050') Instruments - Torque converter oil temperature, engine water
Drum capacity ........................................ 394 m (1293'), 7 layers temperature, air pressure, fuel, speedometer, tachometer, hour
Maximum single line pull (1st layer).............9,900 kg (21,800 lbs) meter and odometer / tripmeter. Hydraulic oil pressure is
Maximum permissible linepull wire strength...7,200 kg (15,900 lbs) monitored and displayed on the AML-C display panel.

-2 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

CRANE SPECIFICATIONS
Tadano electronic LOAD MOMENT INDICATOR system
(AML-C) including: TADANO AML-C monitors outrigger extended length and
• Control lever lockout function with audible and visual automatically programs the corresponding "RATED LIFTING
pre-warning CAPACITIES" table.
• Boom position indicator
• Outrigger state indicator Operator's right hand console includes transmission gear selector
• Boom angle / boom length / jib offset angle / jib length / load and sight level bubble. Upper console includes working light
radius / rated lifting capacities / actual loads read out switch, roof washer and wiper switch emergency outrigger set up
• Ratio of actual load moment to rated load moment indication key switch, jib equipped/removed select switch, eco mode switch,
• Automatic speed reduction and slow stop function on boom high speed winch (main / aux) switch, Cab tilt switch. Slewing lock
elevation and slewing lever.
• Working condition register switch
• Load radius / boom angle / tip height / slewing range preset NOTE: Each crane motion speed is based on unladen conditions.
function
• External warning lamp
• Tare function
• Fuel consumption monitor
• Main winch / auxiliarly winch select
• Drum rotation indicator (audible and visible type) main and
auxiliary winch

CARRIER SPECIFICATIONS
TYPE AXLE
Rear engine, left hand steering, driving axle 2-way 1st: Full floating type, steering and driving axle with planetary
selected type by manual switch, 6x2 1st drive, 6x4 1st and 3rd reduction and open differential.
drive. 2nd: Steering and not driving axle.
3rd: Full floating type, steering and driving axle with planetary
FRAME reduction and open differential.
High tensile steel, all welded mono-box construction.
STEERING
ENGINE Hydraulic power steering controlled by steering wheel. Four
Model MITSUBISHI 6M60-TL (Tier2) steering modes available: 2 wheel front, 4 wheel rear, 6 wheel
Type Direct injection diesel coordinated and 6 wheel crab.
No. of cylinders 6
Combustion 4 cycle, turbo charged and after cooled SUSPENSION
Bore x Stroke, mm. (in) 118 x 115 (4.646 x 4.528) 1st: Rigid mounted to frame.
Displacement, liters (cu. in) 7.54 (460) 2nd and 3rd: "Hydro-Pneumatic suspension cylinders" with
Air inlet heater 24 volt preheat levering adjustment and oscillation.
Air cleaner Dry type, replaceable element
Oil filter Full flow with replaceable element BRAKE SYSTEMS
Fuel filter Full flow with replaceable element Service: Air over hydraulic disc brakes on
Fuel tank, liters (gal.) 300 (79.2), right side of carrier all 6 wheels. Parking/Emergency: Spring applied-air released
Cooling Liquid pressurized, recirculating by-pass brake acting on input shaft of 1st and 3rd axle.
Radiator Fin and tube core, thermostat controlled Auxiliary: Electro- pneumatic operated exhaust brake.
Fan, mm (in.) Suction type, 6-blade, 600 (23.6) dia.
Starting 24 volt TIRES - 26.5R25☆☆ Air pressure: 650 kPa (94 psi)
Charging 24 volt system, negative ground
Battery 2-120 amp. Hour OUTRIGGERS
Compressor, air, l /min (CFM) 830 (29) at 2,600 rpm Four hydraulic, beam and jack outriggers.
Output, Max. kW (HP) Gross 200 (267) at 2,600 rpm Vertical jack cylinders equipped with integral holding valve. Each
Torque, Max. Nm (ft-lb) 785 (579) at 1,400 rpm outrigger beam and jack is controlled independently from cab.
Capacity, liters (gal.) Beams extend to 8.2 m (26'10-7/8") center-line and retract to
Cooling water 13 (3.4) within 3.315 m (10' 10-1/2") overall width with floats.
Lubrication 13–15 (3.4–4.0) Outrigger boxes are self-removable for ease of transportation.
Fuel 300 (79.2) Outrigger jack floats are attached thus eliminating the need of
manually attaching and detaching them. Controls and sight
TRANSMISSION bubble located in superstructure cab. Four outrigger extension
Electronically controlled full automatic transmission. Torque lengths are provided with corresponding "RATED LIFTING
converter driving full powershift with driving axle selector. 5 CAPACITIES" for crane duty in confined areas.
forward and 2 reverse speeds, constant mesh. Min. Extension 2.99 m (9' 9-3/4") center to center
2 speeds - high range - 2 wheel drive; 4 wheel drive Mid. Extension 5.50 m (18' 1/2") center to center
3 speeds - low range - 4 wheel drive Mid. Extension 7.30 m (23'11-3/8") center to center
Max. Extension 8.20 m (26'10-7/8") center to center
TRAVEL SPEED Float size (Diameter) 0.57 m (1'10-1/2")
15 km/h (9.3 mph) with counterweight
4 km/h (2.5 mph) without counterweight

GRADE ABILITY (tanθ) - 44% (with counterweight 29.3 t (64,600

lbs)), 52% (with counterweight 18.2 t (40,100 lbs)), 30%*
* Machine should be operated within the limit of engine crankcase
design (17º: MITSUBISHI 6M60-TL).

-3 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

STANDARD EQUIPMENT
- Six section extended boom by single telescoping cylinder - Boom angle indicator
13.1 m–61.0 m (42.8'–200.1') - Outrigger extension length detector
- 10.3 m (33.8') or 18.0 m (59.1') bi-fold lattice jib, offset angle (5–40º) - Electronic crane monitoring system
by tilt cylinder. - Rear view mirrors (right and left side)
- Quick reeving type bi-fold jib - Fenders
- Anti-Two block device (overwind cutout) - Air dryer
- Mirror for main and auxiliary winch - Complete highway light package
- Work lights - Towing hooks-Front and rear
- Variable speed main winch with grooved drum, cable follower and - Hook block tie down (front bumper)
320 m of 19 mm (1050' of 3/4") cable. - Weighted hook storage compartment
- Variable speed auxiliary winch with grooved drum, cable follower and - Halogen head lamp
225 m of 19 mm (738' of 3/4") cable. - Self-removable outrigger boxes
- Drum rotation indicator (audible,visible and thumper type) main and - Independently controlled outriggers
auxiliary winch - Four outrigger extension positions
- Auxiliary lifting sheave (single top) stowable - Self-storing outrigger pads
- 2-speed winch - Electronic controlled automatic transmission driven by torque
- Tadano twin swing system and 360º positive swing lock converter
- Positive control - 6 x 4 x 6 drive/steer
- Hydraulic oil cooler - 1st axle: open differential
- 15º tilt cab - 3rd axle: open differential
- 3 way adjustable cloth seat with armrests, high back and seat belt - Automatic rear axle oscillation lockout system
- Tilt-telescoping steering wheel - 26.5R25☆☆ tires
- Tinted safety glass and sun visor - Disc brakes
- Front windshield wiper and washer - Water separator with filter (high filtration)
- Roof window wiper and washer - Back-up alarm
- Power window (cab door ) - 24 volt electric system
- Cigarette lighter and ashtray - Tool storage compartment
- Cab floor mat - Tire inflation kit
- Pump disconnect in operator's cab - Mitsubishi 6M60-TLA3B turbo charged after cooled engin (267HP)
- Air conditioner (hot water heater and cooler) with exhaust brake
- Full instrumentation package - Engine over-run alarm
- Self centering finger control levers with pilot control - Lifting eyes
- Control pedals for boom elevating and boom telescoping - Fuel consumption monitor
- Low oil pressure/high water temp. warning device (visual) - Eco mode system
- 2nd and 3rd steer centering light - Self-removable counterweight
- Air cleaner dust indicator
- Tadano electronic load moment indicator system (AML-C)
- Tare function

OPTIONAL EQUIPMENT
- Additional weight 11.1 t (24,500 lbs) - 100 metric ton (110 ton) - 7 sheaves with hook block and safety latch
- Removable boom system - 45 metric ton (50 ton) - 3 sheaves with hook block and safety latch
- Working lamp with remort controller - 7.2 metric ton (7.9 ton) - Weighted hook with swivel and safety latch
- Boom and jib mounted aircraft warning light
- Wind speed indicator - Telematics (machine data logging and monitoring system) with
- Emergency steering system HELLO-NET via internet (availability depends on countries)
- Over-unwinding prevention - Outrigger load display and warning
- Insert jib - Inclinometer (electronic inclination indicator)
- Short jib

HOISTING PERFORMANCE
LINE SPEEDS AND PULLS DRUM WIRE ROPE CAPACITIES
Main or auxiliary winch - 0.382 m (15") drum Main and auxiliary drum grooved lagging
Line speeds1 Line pulls Available2 Wire 19 mm (3/4") wire rope
Layer rope
Low High Low Rope per layer Total wire rope
layer
m/min F.P.M m/min F.P.M kgf Lbs. Meter Feet Meter Feet
1st 77 253 108 354 9,900 21,800 1 44.8 147.0 44.8 147.0
2nd 84 276 117 384 9,010 19,900 2 48.6 159.4 93.4 306.4
3rd 91 299 126 413 8,270 18,200 3 52.5 172.2 145.9 478.7
4th 97 318 136 446 7,640 16,800 4 56.3 184.7 202.2 663.4
5th 104 341 145 476 7,090 15,600 5 60.1 197.2 262.3 860.6
6th 110 361 154 505 6,620 14,600 6 63.9 209.6 326.2 1070.2
7th3 117 384 163 535 6,210 13,700 7 67.7 222.1 393.9 1292.3

- Maximum permissible line pull wire strength.

7,200 kg (15,900 lbs) with 7 x 35 class rope. DRUM DIMENSIONS (Main and auxiliary)
mm Inch
1
Line speed based only on hook block, not loaded. Root diameter 382 15
2
Developed by machinery with each layer of wire rope, but not based Length 742 29-1/4
on rope strength or other limitations in machinery or equipment. Flange diameter 677 26-5/8
3
Seventh layer of wire rope are not recommended for hoisting
operations.

-4 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

GR-1600XL WORKING RANGE CHART

Hydraulic offset jib
Counterweight 29.3 t

BOOM

20° 40 Approx.
°
5° 2.6 m
85

80

75
61
.0-
m
Bo 70
61
om
+1
JIB
.0- 8.0
m -m 65
81.5° Bo JIB
om
70° +1
0.3 60
-m
JIB Approx.
60° 3.3 m
55
61
.0
-m

LIFTING HEIGHT (m)

57 50° 50
.0 Bo
-m om
52 Bo 45°
.6 om 45
-m
48 Bo 40°
.2 om
43
.8
-m
Bo 33°
40 SINGLE TOP
-m om
39 Bo 0.6 m
.4 om 35
-m
35 Bo 30°
.0 om
-m Approx.
30 Bo 30
.6 om 2.3 m
-m
26 Bo
.2 om 25
-m 20°
21 Bo
.8 om
-m 20
17 Bo 16°
.4 om
-m
13 Bo 15
.1 om
-m
Bo 10°
om 10

5
0°

0
0 5 10 15 20 25 30 35 40 45 50 55 60 65

LOAD RADIUS (m)

NOTE: Boom and jib geometry shown are for unloaded condition and
machine standing level on firm supporting surface.
Boom deflection and subsequent radius and boom angle change
must be accounted for when applying load to hook.

-5 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

GR-1600XL WORKING RANGE CHART

Hydraulic offset jib
7.0 m Insert jib *Option
Counterweight 29.3 t
BOOM
20° 40
5° °

90 Approx.
2.6 m
85
61
.0-
m
Bo
80
om
+7
.0-
m 75
IN
81.5° SE
RT
J IB 70 JIB
70° +1
8.0
-m
JIB 65
60°
60 Approx.
50° 3.3 m
61
.0-
m 55

LIFTING HEIGHT (m)

Bo
om 48°
50

45

40
SINGLE TOP
0.6 m
35
Approx.
30 2.3 m

25

20

15

10

0
0 5 10 15 20 25 30 35 40 45 50 55 60 65
LOAD RADIUS (m)

NOTE: Boom and jib geometry shown are for unloaded condition and
machine standing level on firm supporting surface.
Boom deflection and subsequent radius and boom angle change
must be accounted for when applying load to hook.

-6 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

GR-1600XL WORKING RANGE CHART

Hydraulic offset jib
14.0 m Insert jib *Option
40
20° ° Counterweight 29.3 t
5°
90 BOOM
85

90 Approx.
61
.0-
2.6 m
m
Bo
om 85
+1
4.0
-m
INS 80
81.5° ER
TJ
IB
+1
70° 8.0
-m
75
JIB
60°
70 JIB
58°
55°
65

61 60 Approx.
.0-

LIFTING HEIGHT (m)

m
Bo 3.3 m
om 55

50

45

40
SINGLE TOP
0.6 m
35
Approx.
30 2.3 m

25

20

15

10

0
0 5 10 15 20 25 30 35 40 45 50 55 60 65
LOAD RADIUS (m)

NOTE: Boom and jib geometry shown are for unloaded condition and
machine standing level on firm supporting surface.
Boom deflection and subsequent radius and boom angle change
must be accounted for when applying load to hook.

-7 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

GR-1600XL WORKING RANGE CHART

Short jib *Option
Counterweight 29.3 t

BOOM

Approx.
2.6 m

40
°
20°
70 JIB
61 65
81.5° .0-
m
Bo
om
70° +3
.6- 60 Approx.
m
JIB 3.3 m
60°
55

50° 50

45
40° LIFTING HEIGHT (m) SINGLE TOP
40
0.6 m
35
30°
Approx.
30 2.3 m

25

20

15

10

0
0 5 10 15 20 25 30 35 40 45 50 55 60 65
LOAD RADIUS (m)

NOTE: Boom and jib geometry shown are for unloaded condition and
machine standing level on firm supporting surface.
Boom deflection and subsequent radius and boom angle change
must be accounted for when applying load to hook.

-8 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)

Boom
COUNTERWEIGHT 29.3 t (64,600 lbs)
ON OUTRIGGERS FULLY EXTENDED 8.2 m (26'10-7/8'') SPREAD
360º ROTATION (Unit: x 1,000 kg)
A 13.1 m 17.4 m 21.8 m 26.2 m 30.6 m 35.0 m 39.4 m 43.8 m 48.2 m 52.6 m 57.0 m 61.0 m
B (42.8') (57.2') (71.6') (86.1') (100.5') (114.9') (129.3') (143.7') (158.1') (172.5') (187.0') (200.1')
2.50 **145.0 90.7 79.0
3.00 *110.6 90.7 79.0 37.0
3.50 *101.5 90.7 79.0 66.0
4.00 93.6 90.1 79.0 66.0 37.0
4.50 85.9 83.7 79.0 66.0 48.2
5.00 79.3 78.1 75.8 66.0 48.2 35.2
5.50 73.5 73.2 71.0 66.0 48.2 35.2
6.00 68.3 68.3 66.7 63.5 48.2 38.7
6.50 63.7 64.1 63.6 60.5 48.2 37.5 30.1
7.00 59.6 60.0 60.2 57.8 48.2 35.9 30.1
7.50 56.0 56.4 56.5 55.3 48.2 35.2 30.1 22.1
8.00 52.7 53.1 53.2 52.9 48.0 35.2 29.5 23.9
9.00 46.8 47.3 47.5 47.2 44.8 35.2 27.9 23.9 17.2
10.00 37.3 41.7 41.9 41.6 41.6 35.2 26.2 22.9 18.9 13.5
11.00 37.1 37.3 37.5 37.7 33.2 24.4 22.0 18.9 15.0
12.00 33.4 33.5 34.3 33.9 31.5 22.7 21.0 18.4 15.0 12.0
14.00 27.8 27.6 28.4 28.0 28.4 20.9 19.2 16.9 15.0 12.0 10.4
16.00 23.3 24.0 24.3 24.3 19.3 17.1 15.5 14.1 12.0 10.4
18.00 21.3 20.6 21.3 20.9 17.8 15.4 14.3 13.1 12.0 10.4
20.00 18.4 18.5 18.1 16.5 14.0 12.9 12.1 11.2 10.2
22.00 16.3 16.1 15.7 15.4 12.7 11.8 11.2 10.4 9.6
24.00 14.1 13.6 14.1 11.7 10.8 10.4 9.8 9.0
26.00 12.3 12.8 12.3 10.8 10.1 9.6 9.1 8.4
28.00 8.2 11.4 10.8 10.0 9.4 8.8 8.5 7.8
30.00 10.1 9.6 9.2 8.8 8.2 8.0 7.3
32.00 8.4 8.5 8.6 8.2 7.7 7.4 6.7
34.00 7.6 7.9 7.4 7.3 7.0 6.2
36.00 6.8 7.1 6.6 6.9 6.5 5.8
38.00 6.4 6.1 6.3 5.8 5.4
40.00 5.8 5.8 5.6 5.2 5.0
42.00 5.3 5.0 4.6 4.6
44.00 4.8 4.5 4.1 4.1
46.00 4.1 3.7 3.6
48.00 3.7 3.2 3.2
50.00 2.8 2.8 2.8
52.00 2.5 2.4
54.00 2.2 2.1
56.00 1.8
**Over front with special equipment
*With special Equipment

A: Boom length (m)

B: Load radius (m)

NOTE: In this table, the thick line which divides strength area and stability area is not shown because the figure of this table is indicated the best performance
at the same boom length among the plural telescopic boom patterns.

- 9-
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)

Jib
COUNTERWEIGHT 29.3 t (64,600 lbs)
ON OUTRIGGERS FULLY EXTENDED 8.2 m (26'10-7/8") SPREAD
360º ROTATION
61.0-m (200.1') Boom + 10.3-m (33.8') Hydraulic offset jib 57.0-m (187.0') Boom + 10.3-m (33.8') Hydraulic offset jib
C 5º Tilt 20º Tilt 40º Tilt C 5º Tilt 20º Tilt 40º Tilt
R W R W R W R W R W R W
81.5 14.7 5.5 17.4 5.5 20.4 5.1 81.5 12.9 6.2 15.7 6.2 18.7 5.8
81 15.6 5.5 18.6 5.5 21.1 5.0 81 13.7 6.2 16.5 6.2 19.3 5.7
80 17.2 5.5 19.9 5.4 22.6 4.9 80 15.2 6.2 17.9 6.1 20.6 5.5
79 18.8 5.5 21.2 5.2 24.0 4.7 79 16.7 6.2 19.3 5.9 21.9 5.4
78 20.5 5.5 22.6 5.0 25.2 4.6 78 18.2 6.2 20.6 5.7 23.0 5.2
77 21.9 5.4 24.4 4.9 26.5 4.5 77 19.6 6.2 21.9 5.6 24.3 5.1
76 23.3 5.2 25.3 4.7 27.8 4.4 76 20.8 6.0 23.2 5.4 25.4 4.9
75 24.5 5.0 26.7 4.6 28.9 4.2 75 22.1 5.8 24.3 5.2 26.6 4.8
73 27.3 4.8 29.3 4.4 31.3 4.0 73 24.6 5.4 26.8 4.9 28.9 4.6
70 31.0 4.3 33.0 4.0 34.8 3.8 70 28.2 5.0 30.3 4.6 32.1 4.3
68 33.5 4.1 35.4 3.8 37.0 3.6 68 30.6 4.7 32.4 4.3 34.2 4.1
65 37.2 3.8 38.8 3.6 40.1 3.4 65 33.8 4.3 35.6 4.0 37.1 3.8
63 39.2 3.6 40.9 3.4 42.2 3.3 63 36.1 4.2 37.7 3.9 39.0 3.7
60 42.5 3.3 43.8 3.1 45.1 3.0 60 39.1 3.9 40.6 3.7 41.9 3.5
58 44.5 3.1 46.0 3.0 47.0 2.9 58 41.2 3.7 42.5 3.5 43.7 3.4
55 47.2 2.8 48.6 2.7 49.6 2.7 55 43.9 3.5 45.2 3.3 46.1 3.2
53 49.2 2.7 50.4 2.6 51.1 2.5 53 45.6 3.3 46.9 3.2 47.7 3.1
50 51.6 2.4 52.8 2.3 53.4 2.2 50 48.2 3.1 49.2 2.9 49.9 2.9
48 53.3 2.2 54.3 2.1 54.8 2.1 48 49.6 2.9 50.6 2.8 51.2 2.7
45 55.6 2.0 56.4 1.9 56.8 1.9 45 51.7 2.6 52.7 2.5 53.1 2.5
43 56.9 1.8 57.8 1.8 43 53.1 2.4 54.0 2.4
40 58.9 1.6 59.5 1.5 40 55.0 2.2 55.7 2.1
38 60.1 1.4 60.7 1.3 38 56.2 2.0 56.8 1.9
35 61.6 1.1 62.1 1.1 35 57.8 1.7 58.3 1.6
33 62.7 1.0 63.0 0.9 33 58.8 1.6 59.2 1.5
30 64.0 0.8 30 60.2 1.3 60.4 1.3
28 28 61.0 1.2 61.2 1.2
25 25 62.1 1.1 62.0 1.0
23 23 62.7 1.0
20 20 63.5 0.9
G 1 G 1

COUNTERWEIGHT 29.3 t (64,600 lbs)

ON OUTRIGGERS FULLY EXTENDED 8.2 m (26'10-7/8") SPREAD
360º ROTATION
52.6-m (172.5') Boom + 10.3-m (33.8') Hydraulic offset jib 35.0-m (114.9') Boom + 10.3-m (33.8') Hydraulic offset jib
C 5º Tilt 20º Tilt 40º Tilt C 5º Tilt 20º Tilt 40º Tilt
R W R W R W R W R W R W
81.5 11.3 7.2 14.3 7.2 17.4 6.8 81.5 8.9 10.6 11.3 7.3
81 12.0 7.2 15.0 7.2 18.0 6.7 81 9.3 10.5 11.7 7.2
80 13.4 7.2 16.3 7.2 19.2 6.5 80 10.1 10.2 12.5 7.1
79 14.8 7.2 17.6 7.0 20.3 6.3 79 10.9 10.0 13.2 7.0
78 16.1 7.2 18.8 6.8 21.4 6.1 78 11.9 9.7 14.0 6.9
77 17.5 7.2 19.9 6.6 22.5 5.9 77 12.6 9.5 14.8 6.9
76 18.8 7.2 21.1 6.4 23.6 5.8 76 13.3 9.3 15.5 6.8
75 19.6 6.9 22.3 6.2 24.6 5.6 75 11.8 12.8 14.1 9.1 16.2 6.7
73 22.0 6.5 24.4 5.8 26.7 5.4 73 13.4 12.2 15.6 8.7 17.6 6.5
70 25.7 5.9 27.6 5.4 29.6 5.0 70 15.6 11.3 17.9 8.2 19.7 6.3
68 27.9 5.6 29.8 5.2 31.6 4.8 68 17.2 10.8 19.3 7.9 21.0 6.2
65 31.0 5.2 32.7 4.8 34.3 4.5 65 19.3 10.1 21.4 7.6 22.9 6.1
63 33.2 5.0 34.6 4.6 36.1 4.4 63 20.7 9.6 22.8 7.4 24.2 6.0
60 36.0 4.6 37.5 4.4 38.8 4.2 60 22.8 9.0 24.8 7.1 26.0 5.9
58 37.8 4.4 39.2 4.2 40.4 4.0 58 24.1 8.7 26.0 6.9 27.2 5.8
55 40.4 4.1 41.7 3.9 42.7 3.8 55 26.0 8.2 27.9 6.7 28.9 5.7
53 42.0 3.9 43.3 3.8 44.1 3.6 53 27.2 7.9 29.0 6.5 29.9 5.7
50 44.4 3.7 45.5 3.5 46.1 3.4 50 29.0 7.6 30.7 6.4 31.4 5.7
48 45.9 3.5 46.9 3.3 47.4 3.2 48 30.1 7.4 31.7 6.3 32.4 5.6
45 48.0 3.2 48.8 3.0 49.3 3.0 45 31.7 7.1 33.2 6.1 33.8 5.6
43 49.3 3.0 50.0 2.9 43 32.7 7.0 34.2 6.1
40 51.1 2.7 51.7 2.6 40 34.1 6.8 35.4 6.0
38 52.2 2.5 52.8 2.4 38 35.1 6.6 36.3 5.9
35 53.7 2.2 54.2 2.1 35 36.5 6.5 37.5 5.9
33 54.7 2.0 55.1 1.9 33 37.2 6.4 38.2 5.8
30 55.9 1.7 56.3 1.7 30 38.4 6.3 39.2 5.8
28 56.8 1.6 57.0 1.5 28 39.0 6.0 39.8 5.8
25 57.8 1.4 57.9 1.4 25 39.9 5.7 40.5 5.6
23 58.4 1.3 23 40.5 5.6
20 59.2 1.2 20 41.2 5.4
G 1 G 2
C: Loaded boom angle (º)
R: Load radius (m)
W: Rated lifting capacity (Unit: x 1,000 kg)
G: Number of parts of line
- 10 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)

Jib
COUNTERWEIGHT 29.3 t (64,600 lbs)
ON OUTRIGGERS FULLY EXTENDED 8.2 m (26'10-7/8") SPREAD
360º ROTATION
61.0-m (200.1') + 18.0-m (59.1') Hydraulic offset jib 57.0-m (187.0') Boom + 18.0-m (59.1') Hydraulic offset jib
C 5º Tilt 20º Tilt 40º Tilt C 5º Tilt 20º Tilt 40º Tilt
R W R W R W R W R W R W
81.5 17.1 3.7 22.0 3.7 27.1 3.2 81.5 14.6 4.0 20.0 4.0 24.7 3.3
81 18.0 3.7 22.7 3.7 28.0 3.2 81 15.0 4.0 20.8 4.0 25.5 3.3
80 19.9 3.7 24.7 3.7 29.6 3.1 80 17.2 4.0 22.5 4.0 27.0 3.2
79 21.6 3.7 26.3 3.7 31.1 3.1 79 18.8 4.0 23.8 3.9 28.3 3.2
78 23.4 3.7 27.9 3.6 32.5 3.0 78 20.3 4.0 25.4 3.8 29.7 3.2
77 25.0 3.7 29.3 3.5 34.0 3.0 77 21.9 4.0 26.7 3.7 31.0 3.1
76 26.8 3.7 30.9 3.4 35.3 3.0 76 23.5 4.0 28.2 3.6 32.3 3.1
75 28.5 3.7 32.3 3.3 36.4 2.9 75 25.0 4.0 29.6 3.6 33.4 3.0
73 31.4 3.5 35.0 3.1 39.2 2.8 73 28.1 4.0 32.3 3.5 35.9 3.0
70 35.6 3.2 39.0 2.9 42.6 2.6 70 32.2 3.7 36.2 3.3 39.4 2.9
68 38.4 3.1 41.3 2.7 44.9 2.5 68 34.8 3.5 38.6 3.2 41.8 2.8
65 42.1 2.8 45.3 2.6 48.1 2.4 65 38.5 3.3 42.1 3.0 44.7 2.8
63 44.7 2.7 47.5 2.5 50.3 2.3 63 41.0 3.2 44.4 2.9 46.8 2.7
60 48.4 2.5 50.8 2.3 53.3 2.2 60 44.5 3.0 47.5 2.7 49.7 2.6
58 50.5 2.3 52.9 2.2 55.1 2.1 58 46.6 2.9 49.6 2.6 51.5 2.5
55 53.7 2.1 55.8 2.0 57.6 1.9 55 49.7 2.7 52.5 2.5 54.1 2.4
53 55.6 1.9 57.5 1.8 59.1 1.7 53 51.5 2.5 54.1 2.3 55.4 2.2
50 58.3 1.7 60.0 1.6 61.1 1.5 50 54.1 2.2 56.6 2.1 57.5 2.0
48 59.9 1.5 61.4 1.4 62.5 1.4 48 55.9 2.1 58.0 1.9 58.8 1.9
45 62.4 1.3 63.7 1.2 64.3 1.1 45 58.2 1.8 60.3 1.7 60.6 1.7
43 63.9 1.2 65.0 1.1 43 59.6 1.7 61.5 1.6
40 65.8 0.9 66.8 0.8 40 61.7 1.5 63.1 1.3
38 38 63.0 1.3 64.3 1.2
35 35 64.7 1.0 65.7 0.9
33 33 65.9 0.9 66.6 0.8
30 30
28 28
25 25
23 23
20 20
G 1 G 1

COUNTERWEIGHT 29.3 t (64,600 lbs)

ON OUTRIGGERS FULLY EXTENDED 8.2 m (26'10-7/8") SPREAD
360º ROTATION
52.6-m (172.5') Boom + 18.0-m (59.1') Hydraulic offset jib 35.0-m (114.9') Boom + 18.0-m (59.1') Hydraulic offset jib
C 5º Tilt 20º Tilt 40º Tilt C 5º Tilt 20º Tilt 40º Tilt
R W R W R W R W R W R W
81.5 13.7 4.7 18.8 4.4 23.2 3.4 81.5 9.2 6.4 13.6 5.4 17.9 3.7
81 14.5 4.7 19.6 4.4 23.9 3.4 81 9.6 6.4 14.0 5.3 18.4 3.7
80 16.1 4.7 21.1 4.3 25.2 3.4 80 10.7 6.4 15.0 5.2 19.3 3.6
79 17.6 4.7 22.4 4.2 26.4 3.3 79 11.7 6.4 16.0 5.1 20.1 3.6
78 19.2 4.7 23.8 4.1 27.7 3.3 78 12.7 6.4 16.9 5.0 20.9 3.6
77 20.5 4.7 25.0 4.0 28.9 3.3 77 13.6 6.4 17.8 4.8 21.7 3.5
76 22.0 4.7 26.3 3.9 29.9 3.2 76 14.6 6.4 18.6 4.7 22.5 3.5
75 23.4 4.7 27.7 3.9 31.2 3.2 75 15.6 6.4 19.5 4.6 23.3 3.5
73 26.4 4.6 30.1 3.7 33.4 3.1 73 17.4 6.0 21.4 4.5 24.9 3.4
70 30.0 4.3 33.7 3.5 36.6 3.0 70 20.1 5.6 23.8 4.2 27.1 3.3
68 34.6 4.2 36.0 3.4 38.7 3.0 68 21.8 5.3 25.5 4.1 28.5 3.2
65 36.2 4.0 39.4 3.3 41.5 2.9 65 24.4 5.0 27.9 3.9 30.6 3.2
63 38.4 3.8 41.3 3.2 43.5 2.9 63 26.0 4.8 29.4 3.8 32.0 3.2
60 41.6 3.6 44.5 3.1 46.2 2.8 60 28.4 4.6 31.6 3.6 34.0 3.1
58 43.7 3.4 46.5 3.1 48.0 2.8 58 29.9 4.4 33.1 3.6 35.3 3.1
55 46.5 3.2 49.5 3.0 50.3 2.8 55 32.1 4.2 35.1 3.4 37.1 3.0
53 48.4 3.0 50.8 2.8 51.8 2.7 53 33.6 4.1 36.5 3.4 38.1 3.0
50 51.0 2.7 53.1 2.5 53.7 2.4 50 35.6 3.9 38.3 3.3 39.7 3.0
48 52.6 2.5 54.5 2.4 55.0 2.3 48 37.0 3.8 39.6 3.3 40.7 3.0
45 54.9 2.3 56.6 2.2 56.8 2.1 45 38.8 3.7 41.2 3.2 42.0 3.0
43 56.3 2.2 57.8 2.0 43 40.0 3.6 42.2 3.2
40 58.2 1.9 59.5 1.7 40 41.6 3.5 43.6 3.1
38 59.6 1.7 60.6 1.5 38 43.7 3.4 44.5 3.1
35 61.4 1.4 62.1 1.3 35 44.2 3.3 45.8 3.1
33 62.5 1.3 63.1 1.2 33 45.1 3.3 46.5 3.1
30 64.0 1.1 64.3 1.0 30 46.4 3.2 47.5 3.1
28 65.0 1.0 65.0 0.9 28 47.2 3.2 48.1 3.1
25 66.1 0.8 25 48.2 3.1 48.8 3.1
23 23 48.8 3.1
20 20 49.6 3.1
G 1 G 1
C: Loaded boom angle (º)
R: Load radius (m)
W: Rated lifting capacity (Unit: x 1,000 kg)
G: Number of parts of line
- 11 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)

Jib
COUNTERWEIGHT 29.3 t (64,600 lbs)
ON OUTRIGGERS FULLY EXTENDED 8.2 m (26'10-7/8") SPREAD
360º ROTATION Insert jib: Option
61.0-m (200.1') Boom + 7.0-m (23.0') Insert jib + 18.0-m (59.1') Hydraulic offset jib 57.0-m (187.0') Boom + 7.0-m (23.0') Insert jib + 18.0-m (59.1') Hydraulic offset jib
C 5º Tilt 20º Tilt 40º Tilt C 5º Tilt 20º Tilt 40º Tilt
R W R W R W R W R W R W
81.5 19.3 3.1 24.3 2.9 29.1 2.6 81.5 17.5 3.4 22.3 3.2 27.0 2.7
81 20.3 3.1 25.3 2.9 30.0 2.6 81 18.4 3.4 23.2 3.2 27.9 2.7
80 22.4 3.1 27.4 2.9 31.9 2.6 80 20.3 3.4 25.1 3.2 29.5 2.7
79 24.3 3.1 29.1 2.8 33.6 2.6 79 22.2 3.4 26.9 3.2 31.2 2.7
78 26.3 3.1 30.7 2.7 35.1 2.5 78 23.9 3.4 28.5 3.1 32.5 2.6
77 28.1 3.0 32.6 2.7 36.5 2.4 77 25.7 3.4 30.0 3.0 34.0 2.6
76 29.8 2.9 34.1 2.6 38.0 2.3 76 27.4 3.3 31.5 2.9 35.6 2.6
75 31.4 2.8 35.6 2.5 39.5 2.3 75 28.9 3.2 32.9 2.8 36.8 2.5
73 34.6 2.6 38.5 2.3 42.0 2.1 73 31.9 3.0 35.9 2.7 39.5 2.4
70 39.4 2.4 42.9 2.1 46.0 2.0 70 36.3 2.8 40.0 2.5 43.4 2.3
68 42.2 2.2 45.7 2.0 48.5 1.9 68 39.3 2.7 42.7 2.4 45.8 2.2
65 46.5 2.0 49.7 1.9 52.1 1.8 65 43.2 2.5 46.6 2.3 49.1 2.1
63 49.2 1.9 52.2 1.8 54.4 1.7 63 45.7 2.3 49.1 2.2 51.5 2.1
60 53.2 1.8 56.0 1.7 57.7 1.6 60 49.6 2.2 52.5 2.0 54.5 1.9
58 55.6 1.7 58.2 1.6 59.7 1.5 58 52.0 2.1 54.7 1.9 56.6 1.9
55 58.9 1.5 61.3 1.4 62.4 1.3 55 55.4 2.0 57.8 1.8 59.3 1.8
53 60.8 1.3 63.1 1.2 64.1 1.2 53 57.3 1.8 59.7 1.7 60.7 1.6
50 63.7 1.1 65.7 1.0 66.4 0.9 50 60.0 1.5 62.2 1.5 62.9 1.4
48 65.5 0.9 48 61.8 1.4 63.5 1.2 64.2 1.2
45 45 64.1 1.1 65.7 1.0 66.2 0.9
43 43 65.7 1.0 67.2 0.8
40 40
38 38
35 35
33 33
30 30
28 28
25 25
23 23
G 1 G 1

COUNTERWEIGHT 29.3 t (64,600 lbs)

ON OUTRIGGERS FULLY EXTENDED 8.2 m (26'10-7/8") SPREAD
360º ROTATION Insert jib: Option
52.6-m (172.5') Boom + 7.0-m (23.0') Insert jib + 18.0-m (59.1') Hydraulic offset jib 35.0-m (114.9') Boom + 7.0-m (23.0') Insert jib + 18.0-m (59.1') Hydraulic offset jib
C 5º Tilt 20º Tilt 40º Tilt C 5º Tilt 20º Tilt 40º Tilt
R W R W R W R W R W R W
81.5 15.8 3.9 20.8 3.6 25.1 2.8 81.5 10.1 5.4 14.7 4.5 19.4 3.3
81 16.7 3.9 21.6 3.6 25.8 2.8 81 10.8 5.4 15.3 4.5 19.9 3.3
80 18.5 3.9 23.4 3.6 27.4 2.8 80 12.0 5.4 16.5 4.5 21.0 3.3
79 20.1 3.9 24.8 3.5 28.9 2.8 79 13.1 5.4 17.6 4.4 22.0 3.2
78 21.8 3.9 26.3 3.4 30.3 2.8 78 14.3 5.4 18.6 4.2 22.9 3.2
77 23.4 3.9 27.8 3.3 31.6 2.7 77 15.4 5.4 19.6 4.1 23.8 3.1
76 25.1 3.9 29.2 3.2 32.9 2.7 76 16.4 5.3 20.6 4.0 24.8 3.0
75 26.5 3.8 30.6 3.1 34.1 2.6 75 17.5 5.1 21.6 3.8 25.7 3.0
73 29.4 3.6 33.3 3.0 36.6 2.5 73 19.6 4.8 23.6 3.6 27.4 2.8
70 33.4 3.3 37.3 2.8 40.2 2.4 70 22.6 4.3 26.5 3.3 30.0 2.7
68 36.2 3.2 39.8 2.7 42.4 2.3 68 24.5 4.0 28.4 3.2 31.7 2.6
65 40.2 3.0 43.4 2.5 45.7 2.2 65 27.4 3.7 31.1 3.0 34.0 2.5
63 42.5 2.8 45.7 2.4 47.9 2.2 63 29.2 3.5 32.8 2.8 35.6 2.4
60 46.1 2.7 49.0 2.3 50.8 2.1 60 32.0 3.2 35.3 2.7 37.9 2.3
58 48.4 2.6 51.3 2.3 52.8 2.1 58 33.6 3.0 36.9 2.6 39.3 2.2
55 51.5 2.4 54.2 2.2 55.5 2.0 55 36.2 2.8 39.2 2.4 41.3 2.2
53 53.4 2.2 56.1 2.1 57.1 2.0 53 37.8 2.7 40.7 2.4 42.6 2.1
50 56.1 2.0 58.4 1.8 59.3 1.8 50 40.2 2.6 42.9 2.3 44.4 2.1
48 57.8 1.8 60.0 1.7 60.6 1.6 48 41.6 2.5 44.2 2.2 45.4 2.0
45 60.2 1.6 62.0 1.4 62.4 1.3 45 43.8 2.4 46.2 2.1 47.0 2.0
43 61.6 1.4 63.2 1.2 43 45.1 2.3 47.3 2.1
40 63.6 1.1 65.0 0.9 40 47.0 2.2 49.0 2.0
38 64.9 0.9 66.2 0.8 38 48.2 2.1 50.0 2.0
35 35 49.9 2.1 51.4 1.9
33 33 50.9 2.0 52.3 1.9
30 30 52.2 2.0 53.4 1.9
28 28 53.1 2.0 54.0 1.9
25 25 54.2 1.9 54.9 1.9
23 23 54.9 1.9
G 1 G 1

C: Loaded boom angle (º)

R: Load radius (m)
W: Rated lifting capacity (Unit: x 1,000 kg)
G: Number of parts of line

- 12 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)

Jib
COUNTERWEIGHT 29.3 t (64,600 lbs)
ON OUTRIGGERS FULLY EXTENDED 8.2 m (26'10-7/8") SPREAD
360º ROTATION Insert jib: Option
61.0-m (200.1') Boom + 14.0-m (45.9') Insert jib + 18.0-m (59.1') Hydraulic offset jib 57.0-m (187.0') Boom + 14.0-m (45.9') Insert jib + 18.0-m (59.1') Hydraulic offset jib
C 5º Tilt 20º Tilt 40º Tilt C 5º Tilt 20º Tilt 40º Tilt
R W R W R W R W R W R W
81.5 21.5 2.1 26.4 2.1 32.1 2.1 81.5 19.9 2.8 24.5 2.4 29.6 2.2
81 22.7 2.1 27.5 2.1 33.1 2.1 81 20.9 2.8 25.5 2.4 30.6 2.2
80 25.0 2.1 29.8 2.1 35.0 2.0 80 22.9 2.7 27.6 2.4 32.6 2.2
79 27.1 2.1 31.8 2.1 36.8 2.0 79 24.9 2.7 29.5 2.4 34.0 2.1
78 29.7 2.1 33.8 2.1 38.5 1.9 78 26.7 2.6 31.1 2.3 35.8 2.1
77 31.4 2.1 35.6 2.0 40.0 1.8 77 28.6 2.5 32.8 2.2 37.2 2.0
76 33.5 2.1 37.4 1.9 41.7 1.8 76 30.2 2.4 34.6 2.2 38.8 2.0
75 35.4 2.0 39.0 1.8 43.2 1.7 75 32.2 2.4 36.1 2.1 40.2 1.9
73 38.9 1.9 42.5 1.7 46.2 1.6 73 35.5 2.2 39.4 2.0 43.1 1.8
70 44.0 1.7 47.1 1.5 50.3 1.4 70 40.3 2.0 43.8 1.8 47.2 1.7
68 47.1 1.5 50.2 1.4 53.2 1.3 68 43.5 1.9 46.9 1.7 50.0 1.6
65 51.9 1.4 54.7 1.3 57.1 1.2 65 47.9 1.7 51.1 1.6 53.8 1.5
63 54.8 1.3 57.4 1.2 59.6 1.1 63 50.6 1.6 53.7 1.5 56.2 1.4
60 59.1 1.2 61.4 1.1 63.3 1.1 60 54.8 1.5 57.5 1.4 59.8 1.4
58 61.5 1.0 63.8 1.0 65.3 0.9 58 57.2 1.4 59.8 1.3 61.7 1.3
55 65.0 0.8 55 60.7 1.2 63.2 1.2 64.5 1.1
53 53 63.0 1.1 65.0 1.0 66.2 1.0
50 50 65.8 0.8 67.9 0.8 68.8 0.8
48 48
45 45
43 43
40 40
38 38
35 35
33 33
30 30
28 28
25 25
23 23
G 1 G 1

COUNTERWEIGHT 64,600 lbs (29.3 t)

ON OUTRIGGERS FULLY EXTENDED 26'10-7/8'' (8.20 m) SPREAD
360º ROTATION Insert jib: Option
52.6-m (172.5') Boom + 14.0-m (45.9') Insert jib + 18.0-m (59.1') Hydraulic offset jib 35.0-m (114.9') Boom + 14.0-m (45.9') Insert jib + 18.0-m (59.1') Hydraulic offset jib
C 5º Tilt 20º Tilt 40º Tilt C 5º Tilt 20º Tilt 40º Tilt
R W R W R W R W R W R W
81.5 18.0 3.2 22.4 2.7 27.5 2.4 81.5 12.0 4.4 16.4 3.6 21.2 2.9
81 19.0 3.2 23.4 2.7 28.2 2.4 81 12.8 4.4 17.1 3.6 21.9 2.9
80 20.8 3.1 25.3 2.7 30.1 2.4 80 14.1 4.4 18.4 3.6 23.0 2.9
79 22.6 3.0 26.9 2.6 31.5 2.3 79 15.4 4.3 19.6 3.5 24.1 2.8
78 24.2 2.9 28.4 2.5 33.1 2.3 78 16.6 4.2 20.8 3.4 25.2 2.7
77 26.2 2.9 30.1 2.5 34.5 2.2 77 17.8 4.0 22.0 3.3 26.1 2.6
76 27.8 2.8 31.7 2.4 35.9 2.1 76 19.1 3.9 23.0 3.1 27.2 2.5
75 29.3 2.7 33.2 2.3 37.3 2.1 75 20.1 3.7 24.2 3.0 28.3 2.5
73 32.5 2.5 36.1 2.2 40.2 2.0 73 22.6 3.5 26.4 2.9 30.2 2.3
70 37.1 2.3 40.4 2.0 43.9 1.8 70 25.9 3.1 29.6 2.6 33.1 2.1
68 40.1 2.2 43.2 1.9 46.6 1.8 68 28.1 2.9 31.7 2.4 35.0 2.0
65 44.3 2.0 47.2 1.8 50.2 1.7 65 31.3 2.7 34.7 2.2 37.7 1.9
63 47.0 1.9 49.7 1.7 52.5 1.6 63 33.4 2.5 36.7 2.1 39.5 1.8
60 50.8 1.8 53.4 1.6 55.9 1.5 60 36.4 2.3 39.3 1.9 42.0 1.7
58 53.3 1.7 55.7 1.5 57.8 1.4 58 38.3 2.1 41.2 1.8 43.6 1.6
55 56.9 1.6 59.2 1.5 60.9 1.4 55 41.1 1.9 43.9 1.7 45.9 1.5
53 58.8 1.4 61.2 1.4 62.6 1.3 53 42.9 1.8 45.6 1.6 47.3 1.4
50 61.7 1.2 63.9 1.2 64.9 1.1 50 45.5 1.7 48.0 1.5 49.4 1.4
48 63.6 1.1 65.5 1.0 66.3 1.0 48 47.1 1.6 49.5 1.4 50.7 1.3
45 66.2 0.9 67.9 0.9 68.6 0.9 45 49.5 1.5 51.6 1.3 52.5 1.3
43 67.9 0.8 43 51.0 1.4 53.0 1.3
40 40 53.1 1.4 54.9 1.2
38 38 54.3 1.3 56.0 1.2
35 35 56.1 1.2 57.6 1.2
33 33 57.3 1.2 58.5 1.1
30 30 58.8 1.1 59.8 1.1
28 28 59.7 1.1 60.5 1.1
25 25 60.9 1.1 61.5 1.0
23 23 61.6 1.0
G 1 G 1

C: Loaded boom angle (º)

R: Load radius (m)
W: Rated lifting capacity (Unit: x 1,000 kg)
G: Number of parts of line

- 13 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)

Jib
COUNTERWEIGHT 29.3 t (64,600 lbs)
ON OUTRIGGERS FULLY EXTENDED 8.2 m (26'10-7/8") SPREAD
360º ROTATION Short jib: Option
61.0-m (200.1') Boom + 3.6-m (11.8') Short jib 57.0-m (187.0') Boom + 3.6-m (11.8') Short jib
C 20º Tilt 40º Tilt C 20º Tilt 40º Tilt
R W R W R W R W
81.5 14.1 9.4 15.6 9.2 81.5 12.7 10.8 13.6 10.5
81 14.8 9.2 16.2 9.1 81 13.3 10.7 14.2 10.3
80 16.1 9.0 17.5 8.8 80 14.5 10.3 15.4 10.0
79 17.4 8.7 18.7 8.5 79 15.5 10.0 16.4 9.6
78 18.5 8.4 19.8 8.2 78 16.6 9.6 17.6 9.3
77 19.7 8.1 20.9 7.9 77 17.8 9.3 18.6 9.0
76 20.9 7.8 22.1 7.7 76 18.8 9.0 19.6 8.7
75 22.0 7.5 23.2 7.4 75 19.9 8.7 20.7 8.4
73 24.3 7.0 25.3 6.9 73 22.0 8.1 22.7 7.9
70 27.4 6.3 28.5 6.2 70 25.0 7.4 25.7 7.3
68 29.5 5.9 30.4 5.8 68 26.9 6.9 27.6 6.8
65 32.5 5.3 33.4 5.3 65 29.8 6.3 30.3 6.2
63 34.4 5.0 35.2 4.9 63 31.6 6.0 32.2 5.9
60 37.2 4.5 37.9 4.5 60 34.2 5.4 34.6 5.4
58 39.0 4.3 39.5 4.2 58 35.9 5.1 36.3 5.1
55 41.6 3.9 42.1 3.9 55 38.3 4.7 38.6 4.7
53 43.2 3.7 43.5 3.5 53 39.9 4.5 40.1 4.5
50 45.3 3.1 45.5 2.9 50 42.0 4.0 42.1 3.9
48 46.7 2.7 46.8 2.6 48 43.3 3.6 43.4 3.5
45 48.7 2.3 48.8 2.2 45 45.2 3.1 45.2 3.0
43 49.9 2.0 50.0 1.9 43 46.4 2.8 46.4 2.7
40 51.7 1.7 51.8 1.6 40 48.1 2.4 48.1 2.3
38 52.8 1.5 38 49.2 2.2
35 54.3 1.2 35 50.6 1.9
33 55.2 1.0 33 51.6 1.7
30 56.6 0.8 30 52.8 1.5
28 28 53.6 1.4
25 25 54.6 1.2
20 20 56.0 1.0
G 2 G 2

COUNTERWEIGHT 29.3 t (64,600 lbs)

ON OUTRIGGERS FULLY EXTENDED 8.2 m (26'10-7/8") SPREAD
360º ROTATION Short jib: Option
52.6-m (172.5') Boom + 3.6-m (11.8') Short jib 35.0-m (114.9') Boom + 3.6-m (11.8') Short jib
C 20º Tilt 40º Tilt C 20º Tilt 40º Tilt
R W R W R W R W
81.5 11.2 13.1 12.1 12.6 81.5 6.5 22.2 6.9 18.0
81 11.8 12.9 12.7 12.4 81 6.8 22.0 7.2 17.9
80 12.9 12.4 13.8 11.9 80 7.5 21.7 7.9 17.7
79 13.9 12.0 14.8 11.5 79 8.2 21.3 8.6 17.5
78 15.0 11.6 15.8 11.1 78 8.9 21.0 9.2 17.4
77 16.0 11.2 16.8 10.8 77 9.5 20.7 9.9 17.2
76 17.0 10.7 17.8 10.4 76 10.2 20.4 10.5 17.1
75 18.0 10.3 18.7 10.0 75 10.8 20.1 11.2 16.9
73 19.9 9.6 20.6 9.3 73 12.1 19.6 12.5 16.7
70 22.7 8.6 23.3 8.4 70 14.0 18.9 14.3 16.3
68 24.4 8.0 24.8 7.9 68 15.3 18.5 15.6 16.2
65 27.0 7.3 27.6 7.2 65 17.1 18.0 17.4 15.9
63 28.7 6.9 29.2 6.8 63 18.3 17.7 18.6 15.8
60 31.1 6.3 31.6 6.3 60 19.9 16.9 20.2 15.6
58 32.7 6.0 33.1 5.9 58 21.0 16.3 21.3 15.5
55 35.0 5.6 35.3 5.5 55 22.5 15.2 22.9 14.9
53 36.5 5.3 36.7 5.2 53 23.5 14.1 23.8 13.8
50 38.4 4.7 38.6 4.6 50 24.9 12.6 25.1 12.5
48 39.7 4.3 39.8 4.2 48 25.8 11.8 26.0 11.7
45 41.5 3.8 41.5 3.6 45 27.1 10.8 27.2 10.7
43 42.6 3.4 42.6 3.3 43 27.9 10.2 28.0 10.1
40 44.2 3.0 44.2 2.9 40 29.0 9.4 29.2 9.3
38 45.2 2.7 38 29.8 8.9
35 46.6 2.4 35 30.8 8.3
33 47.5 2.2 33 31.4 8.0
30 48.7 1.9 30 32.3 7.6
28 49.4 1.8 28 32.9 7.3
25 50.4 1.6 25 33.6 7.0
20 51.7 1.4 20 34.6 6.5
G 2 G 4

C: Loaded boom angle (º)

R: Load radius (m)
W: Rated lifting capacity (Unit: x 1,000 kg)
G: Number of parts of line

- 14 -
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)

WITHOUT COUNTERWEIGHT ON-RUBBER STATIONARY
A Over front and rear 360º Rotation
13.1 m 17.4 m 21.8 m 13.1 m 17.4 m 21.8 m
B C (42.8') C (57.2') C (71.6') C (42.8') C (57.2') C (71.6')
2.50 73 10.0 78 10.0 80 10.0 73 10.0 78 10.0 80 10.0
3.00 71 10.0 76 10.0 79 10.0 71 10.0 76 10.0 79 10.0
3.50 68 10.0 74 10.0 78 10.0 68 9.9 74 10.0 78 10.0
4.00 66 10.0 72 10.0 76 10.0 66 8.0 72 9.7 76 10.0
4.50 63 10.0 71 10.0 75 10.0 63 6.4 71 8.1 75 9.0
5.00 61 9.2 69 10.0 74 10.0 61 5.1 69 6.8 74 7.7
5.50 58 8.0 67 9.5 72 10.0 58 4.0 67 5.7 72 6.6
6.00 55 6.9 65 8.4 71 9.1 55 3.0 65 4.7 71 5.6
6.50 52 5.9 63 7.4 69 8.1 52 2.1 63 3.9 69 4.8
7.00 49 5.1 61 6.5 68 7.4 61 3.1 68 4.1
7.50 46 4.3 59 5.8 67 6.6 59 2.4 67 3.3
8.00 43 3.3 57 5.1 65 5.9 57 1.7 65 2.7
9.00 35 1.8 53 3.7 62 4.6 62 1.7
10.00 49 2.4 59 3.4
11.00 44 1.5 56 2.4
12.00 52 1.7
D 0 40 50 47 56 59
Telescoping conditions (%)
Tele. 1 0 0 0 0 0 0
Tele. 2 0 0 0 0 0 0
Tele. 3 0 0 0 0 0 0
Tele. 4 0 0 0 0 0 0
Tele. 5 0 45 90 0 45 90
E 4 4 4 4 4 4

A: Boom length (m) NOTE: The lifting capacity data stowed in the LOAD MOMENT INDICATOR (AML-C)
B: Load radius (m) is based on the standard number of parts of line listed in the chart.
C: Loaded boom angle (º) Standard number of parts of line for on-rubber operation should be
D: Minimum boom angle (º) according to the chart.
for indicated length (no load)
E: Number of parts of line

WARNING AND OPERATING INSTRUCTIONS

FOR ON RUBBER LIFTING CAPACITIES
1. Rated lifting capacities on-rubber do not exceed 75% of 7. On rubber lifting with "jib" is not permitted. Maximum
tipping loads as determined by SAE J765-Crane Stability Test permissible boom length is 21.8 m (71.6').
Code. 8. When making lift on rubber stationary, set parking brake.
2. On rubber lifting is only permitted without couterweight and 9. The mass of the hook (1,080 kg (2,381 lbs) for 100 metric ton
stationary. Creep operation is prohibited. (110 ton) capacity, 300 kg (661 lbs) for 7.2 metric ton (7.9 ton)
Rated lifting capacities shown in the chart are based on the capacity), slings and all similarly used load handling devices
condition that crane is set on firm level surfaces with must be considered as part of the load and must be deducted
suspension lock applied. Those above thick lines are based on from the lifting capacities.
tire capacity and those below, on crane stability. They are 10. For rated lifting capacity of single top, reduce the rated lifting
based on actual load radius increased by tire deformation and capacities of relevant boom according to a weight reductions
boom deflection. for auxiliary load handling equipment. Capacities of single top
3. If the suspension lock cylinders contain air, the axle will not be shall not exceed 7,200 kg (15,900 lbs) including main hook.
locked completely and rated lifting capacities may not be 11. The lifting capacity data stowed in the LOAD MOMENT
obtainable. Bleed the cylinders according to the operation INDICATOR (AML-C) is based on the standard number of parts
safety and maintenance manual. of line listed in the chart. Standard number of parts of line for
4. Rated lifting capacities are based on proper tire inflation, on rubber operation should be according to the following table.
capacity and condition. Damaged tires are hazardous to safe
operation of crane. Boom length Number of parts of line
5. Tires shall be inflated to correct air pressure. 13.1 m (42.8') to 21.8 m (71.6') 4
Tires Air Pressure
26.5R25☆☆☆ 650 kPa (94 psi)
6. Over front operation shall be performed within 10 degrees in
front of chassis.
Over 360˚ Over
front Rear

Approx. Approx.
10˚ 10˚

-15-
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

WARNING AND OPERATING INSTRUCTIONS

FOR LIFTING CAPACITIES
GENERAL 7. Rated lifting capacities at load radius shall not be exceeded. Do
1. RATED LIFTING CAPACITIES apply only to the machine as not tip the crane to determine allowable loads.
originally manufactured and normally equipped by TADANO LTD. 8. Do not operate at boom lengths, radii, or boom angle, where no
Modifications to the machine or use of optional equipment other capacities are shown. Crane may overturn without any load on
than that specified can result in a reduction of capacity. the hook.
2. Hydraulic cranes can be hazardous if improperly operated or 9. When boom length is between values listed, refer to the rated
maintained. Operation and maintenance of this machine must be lifting capacities of the next longer and next shorter booms for
in compliance with information in the Operation and Maintenance the same radius. The lesser of the two rated lifting capacities
3. Manual supplied with the crane. If this manual is missing, order a shall be used.
replacement through the distributor. 10. When making lifts at a load radius not shown, use the next
The operator and other personnel associated with this machine longer radius to determine allowable capacity.
shall fully acquaint themselves with the latest applicable ASME 11. Load per line should not exceed 7,200 kg (15,900 lbs) for main
B30.5 safety standards for cranes as mentioned in OSHA CFR29 winch and auxiliary winch.
part 1926. 12. Check the actual number of parts of line with LOAD MOMENT
INDICATOR (AML-C) before operation. Maximum lifting capacity
SET UP is restricted by the number of parts of line of LOAD MOMENT
1. Rated lifting capacities on the load chart are the maximum INDICATOR (AML-C). Limited capacity is as determined from the
allowable crane capacities, are based on the machine standing formula, Single line pull for main winch 7,200 kg (15,900 lbs) x
level on firm supporting surface under ideal job conditions. number of parts of line.
Depending on the nature of the supporting surface, it may be 13. The boom angle before loading should be greater to account for
necessary to have structural supports under the outrigger floats deflection. For rated lifting capacities, the loaded boom angle
or tires to spread the loads to a larger surface. and the load radius is for reference only.
2. For outrigger operation, outriggers shall be properly extended 14. Do not operate extension or retraction of the boom with loads.
with tires free of supporting surface before operating crane. 15. For lifting capacity of single top, deduct the weight of the load
handling equipment from the rated lifting capacity of the boom.
OPERATION For the lifting capacity of single top, the net capacity shall not
1. Rated lifting capacities have been tested to and meet minimum exceed 7,200 kg (15,900 lbs) including main boom hook mass
requirements of SAE J1063-Cantilevered Boom Crane Structures attached to the boom.
Method of Test. 16. When the base jib or top jib or both jibs are removed, set the jib
2. Rated lifting capacities do not exceed 85% of the tipping load on state switch to the REMOVED position.
outriggers fully extended as determined by SAE J765-Crane 17. When erecting and stowing jib, be sure to retain it by hand or by
Stability Test Code. other means to prevent its free movement.
Rated lifting capacities for partially extended outriggers are 18. Use "ANTI-TWO-BLOCK DEVICE" disable switch when erecting
determined from the formula, Rated Lifting Capacities=(Tipping and stowing jib and when stowing hook block. While the switch
Load - 0.1 x Tip Reaction)/1.25. is pushed, the winch does not stop, even when overwind
3. Rated lifting capacities above thick lines in the chart are based condition occurs.
on crane strength and those below, on its stability. They are 19. For selected boom length or less with jib, rated lifting capacities
based on actual load radius increased by boom deflection. are determined by loaded boom angle only in the column headed
4. The weight of handling device such as hook blocks, slings, etc., "selected boom + jib".
must be considered as part of the load and must be deducted 20. Outriggers shall be extended 8.2 m (26' 10-7/8") spread when
from the lifting capacities. installing or removing removable counterweight.
5. Rated lifting capacities are based on freely suspended loads and
make no allowance for such factors as the effect of wind, sudden DEFINITIONS
stopping of loads, supporting surface conditions, inflation of 1. Load Radius: Horizontal distance from a projection of the axis of
tires, operating speeds, side loads, etc. Side pull on the boom or rotation to supporting surface before loading to the center of the
jib is extremely dangerous. vertical winch line or tackle with load applied.
Such action can damage the boom, jib or slewing mechanism, 2. Loaded Boom Angle: The angle between the boom base section
and lead to overturning the crane. and the horizontal, after lifting the rated lifting capacity at the
6. Rated lifting capacities do not account for wind on lifted load or load radius.
boom. We recommend against working under the conditions that 3. Working Area: Area measured in a circular arc about the
the load is out of control due to a strong wind.During boom lift, centerline of rotation.
consider that the rated lifting capacity is reduced by 50% when 4. Freely Suspended Load: Load hanging free with no direct
the wind speed is 9 m/s (20 mph) to 12 m/s (27 mph); reduced external force applied except by the winch line.
by 70% when the wind speed is 12 m/s (27 mph) to 14 m/s (31 5. Side Load: Horizontal side force applied to the lifted load either
mph). If the wind speed is 14 m/s (31 mph) or over, stop on the ground or in the air.
operation. During jib lift, stop operation if the wind speed is 9
m/s (20 mph) or over.

-16-
 SPEC. SHEET NO. GR-1600-3-00104/ES-01

WARNING AND OPERATING INSTRUCTIONS

FOR USING THE LOAD MOMENT INDICATOR (AML-C)
1. Set AML select keys in accordance with the actually operating • When a load is lifted in the front or rear position and then
crane conditions and don't fail to make sure, before crane swung to the side area, make sure the value of the LOAD
operation, that the displays on front panel are correct. MOMENT INDICATOR (AML-C) is below the 360º lifting
2. When operating crane on outriggers: capacity.
• Set P.T.O. switch to "ON". 4. This machine is equipped with an automatic slewing stop
• Press the outrigger state select key to register for the device. (For the details, see Operation and Maintenance
outrigger operation. If the display agrees with the actual Manual.) But, operate very carefully because the automatic
state, press the set key to register. After the completion of slewing stop does not work in the following case.
the registration, the pop-up window closes. • During on-rubber operation.
• Press the lift state select key to register the lift state to be • When the "P.T.O" switch is set to "OVERRIDE" and the
used (single top / jib / boom). "OVERRIDE" key switch outside the cab is on.
• Each time the lift state select key is pressed, the display 5. During crane operation, make sure that the displays on front
changes. If the display agrees with the autual state, press panel are in accordance with actual operating conditions.
the set key to register. After the completion of the 6. The displayed values of LOAD MOMENT INDICATOR (AML-C)
registration, the pop-up window closes. are based on freely suspended loads and make no allowance
• When erecting and stowing jib, select the status of jib set for such factors as the effect of wind, sudden stopping of
(Jib lift indicator symbol flickers). loads, supporting surface conditions, inflation of tire,
3. When operating crane on rubber: operating speed, side loads, etc.
• Set P.T.O. switch to "ON". For safe operation, it is recommended when extending and
• Press the outrigger state select key to register for the on lowering boom or slewing, lifting loads shall be appropriately
rubber operation. Each time the outrigger state select key reduced.
is pressed, the display changes. Select the stationary 7. LOAD MOMENT INDICATOR (AML-C) is intended as an aid to
operation, the on rubber state indicative symbol flickers. the operator. Under no condition should it be relied upon to
• Press the lift state select key to register the lift state. replace use of capacity charts and operating instruction. Sole
However, pay attention to the following. reliance upon LOAD MOMENT INDICATOR (AML-C) aids in
For stationary operation. place of good operating practice can cause an accident. The
• The front and rear capacities are attainable only when the operator must exercise caution to assure safety.
over front or rear position. The front capacities are
attainable only when the over front position symbol
comes on. When the boom is more than 2 degrees from
centered over front of chassis, 360º capacities are in
effect.

GR-1600XL Axle weight distribution chart

Hydrauric offset jib Kilograms Pounds
GVW 1st 2nd 3nd GVW 1st 2nd 3nd
Basic machine 91,154 29,398 30,640 31,116 200,960 64,812 67,550 68,599
Remove: 1. 7.2 metric ton (7.9 ton) hook block -300 -421 61 61 -661 -928 134 134
2. 100 metric ton (110 ton) hook block -1,080 -1,771 346 346 -2,381 -3,904 763 763
3. Counterweight 11,100 kg (24,500 lbs) -11,120 3,351 -7,236 -7,236 -24,515 7,388 -15,953 -15,953
4. Counterweight 18,200 kg (40,100 lbs) -18,160 5,473 -11,816 -11,816 -40,036 12,066 -26,050 -26,050
5. Front and rear outrigger boxes and beams -8,962 -3,463 -2,750 -2,750 -19,758 -7,635 -6,063 -6,063
6. Auxiliary Winch & wire rope -1,202 490 -846 -846 -2,650 1,080 -1,865 -1,865
7. Boom and Jib -17,424 -22,543 2,559 2,559 -38,413 -49,699 5,642 5,642

-17-
MEMO
MEMO
 (International Sales Division) Te l : +81-(0)3-3621-7750
Fax: +81-(0)3-3621-7785
4-12, Kamezawa 2-chome,
URL http://www.tadano.com/
Sumida-ku, Tokyo 130-0014, Japan Printed in Japan
E-mail info@tadano.com
2016-5-1