GT 800 1 90102 - Us 02 PDF
GT 800 1 90102 - Us 02 PDF
GT 800 1 90102 - Us 02 PDF
DIMENSIONS
1
TT-800XXL
80 Ton Capacity (72.6 Metric Tons)
(MIN.2080)
6' 9-7/8"
(MID.4800)
15' 9"
1'
23' 7-1/2"
(MAX.7200)
7-1
( 5 0 1/16
0) "
19'8-3/16"(6000)
( )
MIN.37'8-11/16"~MAX.144'4-1/4"(11500~44000)
6'13/16"(1850)
11'10-7/8"(3630)
20 o
13
o
2'4"(712)
1'3/16"
(310)
GENERAL DIMENSIONS
Tire : 445/65R22.5(Front)
315/80R22.5(Rear)
Feet Meters
Turning radius
Front tire (curb to curb) 40' 8" 12.4
Over jib 48' 7" 14.8
6'11-7/8"(2132)
CRANE SPECIFICATIONS
WIRE ROPE - Warrington seal wire, extra improved plow steel,
BOOM preformed, independent wire rope core, right regular lay.
5-section full power synchronized telescoping boom, 3/4"(19 mm) 6X37 class
37.7'~144.4' (11.5m~44m), of round hexagonal box construction
with 7-sheaves, 17-5/16" (0.440m) root diameter, at boom head. HOOK BLOCKS
The synchronization system consists of double acting 2-telescope 6.2 ton (5.6 metric ton) - Weighted hook with swivel and
cylinders, two extension cables and retraction cable. Hydraulic safety latch, for 3/4"(19mm) wire rope.
cylinder fitted with holding valve. Two easily removable wire rope
guards, rope dead end provided on both sides of boom head. HYDRAULIC SYSTEM
Boom telescope sections are supported by wear pads both
vertically and horizontally. Selection of 2 boom telescoping modes. PUMPS - Two variable piston pumps for crane functions.
Tandem gear pump for swing and optional equipment.
BOOM ELEVATION - By a double acting hydraulic cylinder Powered by carrier engine. Pump disconnect for crane is
with holding valve. Elevation -2o~80o, combination controls for engaged/ disengaged by rocker switch from carrier cab.
hand or foot operation. Boom angle indicator.
CONTROL VALVES - Multiple valves actuated by pilot
JIB - Double stage lattice type, 3.5o, 25o or 45o offset (tilt type). pressure with integral pressure relief valves.
Single sheave, 15-5/8"(0.396m) root diameter, at base and top
jib head. Stored alongside base boom section. Jib length is RESERVOIR - 185 gallon (700 lit.) capacity. External sight
32.5' (9.9m) or 58.1' (17.7m). Assistant cylinders for mounting level gauge.
and stowing, controlled at right side of superstructure.
Self stowing jib mounting pins. FILTRATION - 26 micron return filter, full flow with bypass
protection, located inside of hydraulic reservoir. Accessible for
AUXILIARY LIFTING SHEAVE (SINGLE TOP) (OPTIONAL) - easy replacement.
Single sheave, 15-5/8"(0.396m) root diameter. Mounted to main
boom head for single line work (stowable). OIL COOLER - Air cooled fan type.
DRUM - Grooved 15-3/4"(0.40m) root diameter x 22-3/4" Dash-mounted engine start/stop, monitor lamps, cigarette
(0.578m) wide. Wire rope: 797' of 3/4"diameter rope (243m of lighter, telescoping mode I / II switch, low noise mode switch,
19mm). Drum capacity: 1,095.5' (333.9m) 7 layers. Maximum line front washer and wiper switch, power window switch, swing
pull (permissible): 15,200lbs. (6,880kg)*. Maximum line speed: brake switch, telescoping / auxiliary winch select switch,
585FPM (178m/min). main winch / auxiliary winch selector switch, swing stop
cancel switch, slow elevation stop cancel switch, free swing /
AUXILIARY HOIST - Variable speed type with grooved drum lock swing selector switch and ashtray.
driven by hydraulic axial piston motor through winch speed Outrigger controls (OPTIONAL).
reducer. Power load lowering and raising. Equipped with
automatic brake (neutral brake) and counterbalance valve. Instruments - Hydraulic oil pressure is monitored and displayed
Controlled independently of main hoist. Equipped with cable on the AML-L display panel.
follower. Drum rotation indicator(OPTIONAL).
2
Tadano electronic LOAD MOMENT INDICATOR system TADANO AML-L monitors outrigger extended length and
(AML-L) including: automatically programs the corresponding "RATED LIFTING
h Control lever lockout function CAPACITIES" table.
h Load radius / boom angle / tip height / swing range
preset function 2nd boom emergency / 3rd,4th,top boom emergency
h Warning buzzer telescoping switch. Correct jib status select switch.
h Boom angle / boom length / jib offset angle / load Upper console includes working light switch, roof
radius / rated lifting capacities / actual loads read out washer and wiper switch, oil cooler switch, emergency
h Ratio of actual load moment to rated load moment outrigger set up key switch and air conditioning control
indication switch. Swing lock lever and 3 way adjustable seat
h Automatic Speed Reduction and Soft Stop function with high back.
on boom elevation and swing (swing range restricted only)
h Working condition register switch NOTE: Each crane motion speed is based on unladen
h External warning lamp conditions.
CARRIER SPECIFICATIONS
SUSPENSION - Front: Load sharing type with leaf springs.
MANUFACTURER - FAUN GmbH Rear: Solid mounted tandem with equalizer beam.
MODEL - KF70-4 BRAKE SYSTEMS - Service: Full air brakes on all wheels. Dual
air line system. Parking: Spring loaded brake on rear 4-wheel
TYPE - Left hand steering, 8x4 controlled by knob of spring brake valve. Emergency: Spring
loaded brake on rear 4-wheel. ABS system.
FRAME - High tensile steel, all welded mono-box construction.
TIRES - Front: 445/65R22.5 SingleX4 Rear: 315/80R22.5 DualX4
TRANSMISSION - Automatically shifting transmission system Spare: 445/65R22.5 SingleX1
with the possibility of semi-automatic operation. 12 forward and
2 reverse speeds. OUTRIGGERS - Four hydraulic, beam and jack outriggers.
Vertical jack cylinders equipped with integral holding valve. Each
TRAVEL SPEEDS - outrigger beam and jack is controlled independently from either
Gear step/Gear Traveling speeds in side of carrier. Beams extend to 23' 7-1/2" (7.2 m) center-line and
mph / k.p.h retract to within 8' 6" (2.59 m) overall width. Equipped with four
1st gear 0-3.91(0-6.3) stowable plastic floats. Controls and sight bubble located on both
2nd gear 4.97(8.0) side of carrier. Three outrigger extension lengths are provided
3rd gear 6.46(10.4) with corresponding "RATED LIFTING CAPACITIES" for crane duty
4th gear 8.32(13.4) in confined areas.
5th gear 10.50(16.9) Min. extension 6' 9-7/8"(2.08m) center to center
6th gear 13.48(21.7) Mid. extension 15' 9"(4.8m) center to center
7th gear 17.77(28.6) Max. extension 23' 7-1/2"(7.2m) center to center
8th gear 22.87(36.8)
9th gear 29.45(47.4) Float size(Diameter) 1' 7-11/16" (0.5m)
10th gear 37.78(60.8)
11th gear 47.97(77.2) FRONT JACK - A fifth hydraulically operated outrigger jack.
12th gear 61.51(99.0) Mounted to the front frame of carrier. Hydraulic cylinder equipped
1st Revers gear 4.23(6.8) with integral holding valve and steel float.
2nd Revers gear 5.41(8.7) Float size(Diameter) 1' 3-11/16"(0.4m)
AXLES - Front: Full floating type, steering axle. CARRIER CAB - One man full with cab of composite structure
Rear: Full floating type, driving axle with inter-wheel (steel sheet metal and fiberglass), windshield of laminated safety
differential lock. glass with windshield wiper and washer, sliding side windows of
hardened glass. Driver seat adjustable and air-suspended with
STEERING - Dual-circuit hydraulic and mechanical steering headrests and 3 point safety belts. 2 rear-view mirrors (electrically
of both front axles with hydraulic power booster. 3rd axle reduction adjustable), 1 wide angle mirror and additional curb mirror, all
gear-mounted emergency steering pump. Tilt telescoping steering mirrors heated. Engine dependent warm-water heater with
wheel. defroster nozzles for windshield and cab floor. Instrumentation
includes speedometer, tachograph, rpm counter with hour meter,
fuel level gauge, air pressure gauge and engine warning lamp,
oil pressure control lamp.
OPTIONAL EQUIPMENT
FOR SUPERSTRUCTURE FOR CARRIER
- Auxiliary lifting sheave (single top) stowable - Rotary beacon
- Hot water cab heater and air conditioner (Upper cab)
- Hook block tie down front bumper
- Mirror for main and auxiliary hoists
- Electric fan in cab
- Drum rotation indicator (thumper type) main and auxiliary hoist
- Non-slip paint
- Extension exhaust pipe
- Back cover of left side superstructure
- Counterweight position indicator
- Outrigger controls and sight bubble located in superstructure cab
- 8,000lbs removable counterweight
4
HOISTING PERFORMANCE
LINE SPEEDS AND PULLS DRUM WIRE ROPE CAPACITIES
Main or auxiliary hoist - 15'-3/4" (0.4m) drum Main and auxiliary drum grooved lagging
Wire
Line pulls 3/4" (19mm) wire rope
Layer Speed Line speeds2 rope
Available1 Permissible4 Rope per layer Total wire rope
layer
F.P.M m/min Lbs. kgf Lbs. kgf Feet Meters Feet Meters
1st High 378 115 18,200 8,260 15,200 6,880 1 123.0 37.5 123.0 37.5
2nd High 413 126 16,700 7,570 13,900 6,310 2 134.2 40.9 257.2 78.4
3rd High 448 136 15,400 6,990 12,800 5,820 3 145.3 44.3 402.6 122.7
4th High 482 147 14,300 6,490 11,900 5,410 4 156.5 47.7 559.1 170.4
5th High 502 157 13,400 6,060 11,100 5,050 5 167.7 51.1 726.7 221.5
6th High 551 168 12,500 5,680 10,400 4,730 6 178.8 54.5 905.5 276.0
7th3 High 585 178 11,800 5,350 9,800 4,460 7 190.0 57.9 1095.5 333.9
1
Developed by machinery with each layer of wire rope, but not based DRUM DIMENSIONS
on rope strength or other limitation in machinery or equipment. Inch mm
2
Line speeds based only on hook block, not loaded. Root diameter 15-3/4" 400
3
Seventh layer of wire rope is not recommended for hoisting operations. Length 22-3/4" 578
4
Permissible line pull may be affected by wire rope strength. Flange diameter 27-3/8" 695
5
TT-800XXL WORKING RANGE CHART
Telescoping Mode I
NOTE : 1.Boom and jib geometry shown are for unloaded condition and
machine standing level on firm supporting surface.
Boom deflection and subsequent radius and boom angle change
must be accounted for when applying load to hook.
TT-800XXL WORKING RANGE CHART
Telescoping Mode II
NOTE : 1.Boom and jib geometry shown are for unloaded condition and
machine standing level on firm supporting surface.
Boom deflection and subsequent radius and boom
angle change must be accounted
for when applying load to hook.
TT-800XXL-1 WORKING RANGE CHART
Telescope mode I
6
TT-800XXL-1 WORKING RANGE CHART
Telescope mode II
7
WEIGHT REDUCTIONS FOR AUXILIARY
LOAD HANDLING EQUIPMENT
Load Handling Epuipment
80ton,5Sheave Hook Block(See Hook Block for actual weight) 1,850 (lbs.)
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD,
15,700lbs COUNTERWEIGHT, 360o ROTATION, FRONT JACK EXTENDED
A 37.7' 51 64.4 64.4 91 91 117.7 117.7
E B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m) B (27.75m) B (35.87m) B (35.87m)
0 31.7 39,100 45.0 19,200 58.3 11,000 58.3 15,800 84.7 5,000 84.7 8,200 110 2,200 110 4,500
Telescoping
mode I ,II I I II I II I II
NOTE: ・The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-L) is based on the standard number of parts of line
listed in the chart.
・Standard number of parts of line for each boom length should be according to the following table.
Boom Length in 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top
Feet (meters) (11.5) (11.5 to 15.56) (15.56 to 19.62) (19.62 to 27.75) (27.75 to 44.0) Jib
Number of parts of
16 12 10 5 4 1
line
8
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
15,700lbs COUNTERWEIGHT, 360o ROTATION
Boom Boom
144.4' (44.0m) Boom + 32.5' (9.9m) Jib 144.4' (44.0m) Boom + 58.1' (17.7m) Jib
Angle Angle
in 3.5o Tilt 25o Tilt 45o Tilt in 3.5o Tilt 25o Tilt 45o Tilt
Degree R W R W R W Degree R W R W R W
80o 33.6 9,900 45.3 8,800 52.7 8,100 80o 40.6 5,900 65.3 5,400 74.7 3,400
75o 50.5 9,900 61.7 8,700 67.5 7,300 75o 60.6 5,900 82.8 4,800 90.1 3,400
70o 66.0 9,700 75.5 7,600 81.1 6,600 70o 79.2 5,900 99.0 4,200 105.0 3,400
65o 80.1 7,900 89.2 6,600 93.9 6,000 65o 96.2 4,900 115.0 3,700 119.0 3,100
60o 92.9 5,600 102.0 5,100 105.0 5,100 60o 111.0 3,700 129.0 3,300 131.0 2,900
55o 105.0 3,800 112.0 3,600 115.0 3,600 55o 125.0 2,300 141.0 2,300 142.0 2,100
50o 116.0 2,500 123.0 2,400 125.0 2,500
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
o
15,700lbs COUNTERWEIGHT, 360 ROTATION
Boom 117.7' (35.87m) Boom (telescoping mode I ) + Boom 117.7' (35.87m) Boom (telescoping mode I ) +
Angle 32.5' (9.9m) Jib Angle 58.1' (17.7m) Jib
in 3.5o Tilt 25o Tilt 45o Tilt in 3.5o Tilt 25o Tilt 45o Tilt
Degree R W R W R W Degree R W R W R W
80o 25.4 12,300 37.8 10,300 45.1 8,300 80o 32.7 7,900 55.3 5,700 66.9 3,700
75o 39.6 12,300 51.0 10,000 57.3 8,000 75o 49.6 7,900 70.2 5,200 80.3 3,700
70o 53.4 12,100 63.2 8,800 68.6 7,400 70o 65.8 7,100 84.2 4,700 92.5 3,600
65o 66.1 9,900 74.8 7,700 79.0 6,700 65o 80.2 6,000 97.2 4,200 104.0 3,500
60o 77.7 8,400 85.6 6,800 89.0 6,200 60o 93.4 5,100 109.0 3,800 114.0 3,300
55o 88.0 6,600 95.5 6,000 98.3 5,600 55o 106.0 4,500 120.0 3,500 123.0 3,100
50o 97.0 4,900 104.0 4,600 106.0 4,600 50o 116.0 3,200 129.0 3,000 131.0 2,900
45o 106.0 3,600 112.0 3,400 114.0 3,500 45o 126.0 2,200 137.0 2,100 139.0 2,100
40o 114.0 2,700 119.0 2,600 40o 135.0 1,500 145.0 1,500
35o 121.0 2,000 126.0 1,900
30o 127.0 1,400 131.0 1,400
25o 133.0 1,000
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
15,700lbs COUNTERWEIGHT, 360o ROTATION
Boom 117.7' (35.87m) Boom (telescoping mode II ) + Boom 117.7' (35.87m) Boom (telescoping mode II ) +
Angle 32.5' (9.9m) Jib Angle 58.1' (17.7m) Jib
in 3.5o Tilt 25o Tilt 45o Tilt in 3.5o Tilt 25o Tilt 45o Tilt
Degree R W R W R W Degree R W R W R W
80o 27.0 11,000 39.3 10,300 46.5 8,300 80o 34.1 6,300 56.7 5,700 67.9 3,700
75o 41.4 11,000 52.2 9,300 58.4 7,700 75o 50.8 6,300 71.5 5,100 81.3 3,700
70o 55.3 10,600 64.5 8,000 69.6 6,900 70o 66.8 6,300 84.7 4,400 93.2 3,600
65o 67.2 8,600 75.9 7,000 80.0 6,200 65o 81.0 5,300 97.2 3,900 104.0 3,300
60o 78.6 7,100 86.6 6,200 89.6 5,700 60o 94.2 4,500 109.0 3,500 113.0 3,000
55o 88.9 5,900 96.0 5,300 98.1 5,200 55o 106.0 3,900 121.0 3,100 127.0 2,800
50o 98.5 5,000 105.0 4,600 106.0 4,500 50o 117.0 3,300 132.0 2,800 138.0 2,700
45o 108.0 4,300 113.0 4,100 114.0 4,000 45o 128.0 2,800 141.0 2,600 145.0 2,500
40o 116.0 3,800 120.0 3,600 40o 137.0 2,400 149.0 2,300
35o 124.0 3,400 127.0 3,300 35o 145.0 2,100 156.0 2,000
30o 130.0 3,100 133.0 3,000 30o 152.0 1,900 161.0 1,800
25o 136.0 2,800 137.0 2,700 25o 159.0 1,700 164.0 1,600
9
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
o
7,700lbs COUNTERWEIGHT, 360 ROTATION
A 37.7 51 64.4 (19.62m) 91 (27.75m) 117.7 (35.87m) 131 144.4
B C (11.5m) C (15.56m) C C C C C C C (39.93m) C (44.0m)
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD,
7,700lbs COUNTERWEIGHT, 360o ROTATION, FRONT JACK EXTENDED
A 37.7' 51 64.4 64.4 91 91 117.7
E B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m) B (27.75m) B (35.87m)
0 31.7 32,900 45.0 15,300 58.3 7,800 58.3 12,900 84.7 2,900 84.7 6,100 110 3,000
Telescoping
mode I ,II I I II I II II
NOTE: ・The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-L) is based on the standard number of parts of line
listed in the chart.
・Standard number of parts of line for each boom length should be according to the following table.
Boom Length in 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top
Feet (meters) (11.5) (11.5 to 15.56) (15.56 to 19.62) (19.62 to 27.75) (27.75 to 44.0) Jib
Number of parts of
16 12 10 5 4 1
line
10
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
o
7,700lbs COUNTERWEIGHT, 360 ROTATION
Boom Boom
144.4' (44.0m) Boom + 32.5' (9.9m) Jib 144.4' (44.0m) Boom + 58.1' (17.7m) Jib
Angle Angle
o o o o
in 3.5 Tilt 25 Tilt 45 Tilt in 3.5 Tilt 25o Tilt o
45 Tilt
Degree R W R W R W Degree R W R W R W
o o
80 33.6 9,900 45.3 8,800 52.7 8,100 80 40.6 5,900 65.3 5,400 74.7 3,400
75o 50.5 9,900 61.7 8,700 67.5 7,300 75o 60.6 5,900 82.8 4,800 90.1 3,400
o o
70 65.5 9,500 75.5 7,600 81.1 6,600 70 79.2 5,900 99.0 4,200 105.0 3,400
65o 78.2 6,100 87.6 5,500 92.8 5,400 65o 93.4 3,900 114.0 3,600 118.0 3,100
60o 91.1 3,800 99.6 3,500 104.0 3,500
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
o
7,700lbs COUNTERWEIGHT, 360 ROTATION
Boom 117.7' (35.87m) Boom (telescoping mode I ) + Boom 117.7' (35.87m) Boom (telescoping mode I ) +
Angle 32.5' (9.9m) Jib Angle 58.1' (17.7m) Jib
o o o o o o
in 3.5 Tilt 25 Tilt 45 Tilt in 3.5 Tilt 25 Tilt 45 Tilt
Degree R W R W R W Degree R W R W R W
80o 25.4 12,300 37.8 10,300 45.1 8,300 80o 32.7 7,900 55.3 5,700 66.9 3,700
o o
75 39.6 12,300 51.0 10,000 57.3 8,000 75 49.6 7,900 70.2 5,200 80.3 3,700
70o 53.4 12,100 63.2 8,800 68.6 7,400 70o 65.8 7,100 84.2 4,700 92.5 3,600
65o 66.1 9,900 74.8 7,700 79.0 6,700 65o 80.2 6,000 97.2 4,200 104.0 3,500
60o 76.9 6,800 85.2 6,100 88.8 6,000 60o 92.7 4,500 109.0 3,800 114.0 3,300
55o 86.8 4,700 94.5 4,300 97.6 4,300 55o 104.0 2,900 119.0 2,700 123.0 2,500
50o 96.0 3,200 103.0 3,000 106.0 3,000
o
45 105.0 2,100 111.0 1,900 113.0 2,000
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
7,700lbs COUNTERWEIGHT, 360o ROTATION
Boom 117.7' (35.87m) Boom (telescoping mode II ) + Boom 117.7' (35.87m) Boom (telescoping mode II ) +
Angle 32.5' (9.9m) Jib Angle 58.1' (17.7m) Jib
in 3.5o Tilt o
25 Tilt
o
45 Tilt in o
3.5 Tilt
o
25 Tilt
o
45 Tilt
Degree R W R W R W Degree R W R W R W
o
80 27.0 11,000 39.3 10,300 46.5 8,300 80o 34.1 6,300 56.7 5,700 67.9 3,700
o o
75 41.4 11,000 52.2 9,300 58.4 7,700 75 50.8 6,300 71.5 5,100 81.3 3,700
o o
70 55.3 10,600 64.5 8,000 69.6 6,900 70 66.8 6,300 84.7 4,400 93.2 3,600
65o 67.2 8,600 75.9 7,000 80.0 6,200 65o 81.0 5,300 97.2 3,900 104.0 3,300
60o 78.6 7,100 86.6 6,200 89.6 5,700 60o 94.2 4,500 109.0 3,500 113.0 3,000
55o 88.9 5,900 96.0 5,300 98.1 5,200 55o 106.0 3,900 121.0 3,100 127.0 2,800
50o 98.7 5,000 105.0 4,600 106.0 4,500 50o 117.0 3,200 132.0 2,800 138.0 2,700
45o 107.0 3,900 113.0 3,600 113.0 3,700 45o 127.0 2,400 141.0 2,300 145.0 2,200
40o 115.0 3,000 120.0 2,900 40o 136.0 1,800 149.0 1,700
35o 122.0 2,400 126.0 2,300 35o 144.0 1,300 155.0 1,200
30o 129.0 1,900 132.0 1,800
25o 135.0 1,500 137.0 1,500
R: Load radius in feet
W: Rated lifting capacity in pounds
11
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
o
3,700lbs COUNTERWEIGHT, 360 ROTATION
A 37.7 51 64.4 (19.62m) 91 (27.75m) 117.7 (35.87m) 131 144.4
B C (11.5m) C (15.56m) C C C C C C C (39.93m) C (44.0m)
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD,
3,700lbs COUNTERWEIGHT, 360o ROTATION, FRONT JACK EXTENDED
A 37.7' 51 64.4 64.4 91 91 117.7
E B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m) B (27.75m) B (35.87m)
0 31.7 29,900 45.0 13,400 58.3 6,200 58.3 11,300 84.7 1,800 84.7 5,000 110 2,200
Telescoping
mode I ,II I I II I II II
NOTE: ・The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-L) is based on the standard number of parts of line
listed in the chart.
・Standard number of parts of line for each boom length should be according to the following table.
Boom Length in 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top
Feet (meters) (11.5) (11.5 to 15.56) (15.56 to 19.62) (19.62 to 27.75) (27.75 to 44.0) Jib
Number of parts of
16 12 10 5 4 1
line
12
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
3,700lbs COUNTERWEIGHT, 360o ROTATION
Boom Boom
144.4' (44.0m) Boom + 32.5' (9.9m) Jib 144.4' (44.0m) Boom + 58.1' (17.7m) Jib
Angle Angle
o o o
in 3.5 Tilt 25 Tilt 45 Tilt in 3.5o Tilt 25o Tilt o
45 Tilt
Degree R W R W R W Degree R W R W R W
80o 33.6 9,900 45.3 8,800 52.7 8,100 80
o
40.6 5,900 65.3 5,400 74.7 3,400
o o
75 50.5 9,900 61.7 8,700 67.5 7,300 75 60.6 5,900 82.8 4,800 90.1 3,400
70o 64.7 8,200 74.7 7,100 80.6 6,600 70o 78.0 5,400 99.0 4,200 105.0 3,400
65o 77.1 5,000 86.6 4,500 91.8 4,400
60o 89.6 2,900
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
3,700lbs COUNTERWEIGHT, 360o ROTATION
Boom 117.7' (35.87m) Boom (telescoping mode I ) + Boom 117.7' (35.87m) Boom (telescoping mode I ) +
Angle 32.5' (9.9m) Jib Angle 58.1' (17.7m) Jib
o o o o o o
in 3.5 Tilt 25 Tilt 45 Tilt in 3.5 Tilt 25 Tilt 45 Tilt
Degree R W R W R W Degree R W R W R W
80o 25.4 12,300 37.8 10,300 45.1 8,300 80o 32.7 7,900 55.3 5,700 66.9 3,700
75o 39.6 12,300 51.0 10,000 57.3 8,000 75o 49.6 7,900 70.2 5,200 80.3 3,700
o o
70 53.4 12,100 63.2 8,800 68.6 7,400 70 65.8 7,100 84.2 4,700 92.5 3,600
65o 65.4 8,500 74.6 7,400 79.0 6,700 65o 80.0 5,600 97.2 4,200 104.0 3,500
60o 76.2 5,600 84.6 5,000 88.5 4,900 60o 91.7 3,500 108.0 3,200 114.0 2,900
o
55 86.3 3,600 93.9 3,400 97.2 3,400
o
50 95.7 2,300 103.0 2,100 105.0 2,100
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
3,700lbs COUNTERWEIGHT, 360o ROTATION
Boom 117.7' (35.87m) Boom (telescoping mode II ) + Boom 117.7' (35.87m) Boom (telescoping mode II ) +
Angle 32.5' (9.9m) Jib Angle 58.1' (17.7m) Jib
in 3.5o Tilt 25o Tilt 45o Tilt in 3.5o Tilt 25o Tilt 45o Tilt
Degree R W R W R W Degree R W R W R W
80o 27.0 11,000 39.3 10,300 46.5 8,300 80o 34.1 6,300 56.7 5,700 67.9 3,700
75o 41.4 11,000 52.2 9,300 58.4 7,700 75o 50.8 6,300 71.5 5,100 81.3 3,700
70o 55.3 10,600 64.5 8,000 69.6 6,900 70o 66.8 6,300 84.7 4,400 93.2 3,600
o o
65 67.2 8,600 75.9 7,000 80.0 6,200 65 81.0 5,300 97.2 3,900 104.0 3,300
60o 78.6 7,100 86.6 6,200 89.6 5,700 60o 94.2 4,500 109.0 3,500 113.0 3,000
55o 88.5 5,500 95.8 5,000 98.1 4,900 55o 106.0 3,500 121.0 3,100 127.0 2,800
50o 97.5 4,100 104.0 3,800 106.0 3,800 50o 116.0 2,500 131.0 2,300 138.0 2,200
45o 106.0 3,000 112.0 2,900 113.0 2,900 45o 126.0 1,700 140.0 1,600 144.0 1,600
o o
40 114.0 2,300 119.0 2,100 40 135.0 1,100
35o 122.0 1,700 126.0 1,600
30o 128.0 1,200 132.0 1,200
R: Load radius in feet
W: Rated lifting capacity in pounds
13
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
0 lbs COUNTERWEIGHT, 360o ROTATION
A 37.7 51 64.4 (19.62m) 91 (27.75m) 117.7 (35.87m) 131 144.4
B C (11.5m) C (15.56m) C C C C C C C (39.93m) C (44.0m)
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD,
o
0 lbs COUNTERWEIGHT, 360 ROTATION, FRONT JACK EXTENDED
A 37.7' 51 64.4 64.4 91
E B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m)
0 31.7 26,500 45.0 11,300 58.3 4,500 58.3 9,600 84.7 4,000
Telescoping
mode I ,II I I II II
NOTE: ・The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-L) is based on the standard number of parts of line
listed in the chart.
・Standard number of parts of line for each boom length should be according to the following table.
Boom Length in 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top
Feet (meters) (11.5) (11.5 to 15.56) (15.56 to 19.62) (19.62 to 27.75) (27.75 to 44.0) Jib
Number of parts of
16 12 10 5 4 1
line
14
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
0 lbs COUNTERWEIGHT, 360o ROTATION
Boom Boom
144.4' (44.0m) Boom + 32.5' (9.9m) Jib 144.4' (44.0m) Boom + 58.1' (17.7m) Jib
Angle Angle
o o o
in 3.5 Tilt 25 Tilt 45 Tilt in 3.5o Tilt 25o Tilt o
45 Tilt
Degree R W R W R W Degree R W R W R W
80o 33.6 9,900 45.3 8,800 52.7 8,100 80
o
40.6 5,900 65.3 5,400 74.7 3,400
o o
75 50.5 9,900 61.7 8,700 67.5 7,300 75 60.6 5,900 82.8 4,800 90.1 3,400
o o
70 63.6 6,900 73.9 6,000 79.9 5,800 70 76.1 4,300 97.5 3,800 105.0 3,400
65o 76.3 3,900 85.9 3,500 90.9 3,500
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
0 lbs COUNTERWEIGHT, 360o ROTATION
Boom 117.7' (35.87m) Boom (telescoping mode I ) + Boom 117.7' (35.87m) Boom (telescoping mode I ) +
Angle 32.5' (9.9m) Jib Angle 58.1' (17.7m) Jib
o o o o o o
in 3.5 Tilt 25 Tilt 45 Tilt in 3.5 Tilt 25 Tilt 45 Tilt
Degree R W R W R W Degree R W R W R W
80o 25.4 12,300 37.8 10,300 45.1 8,300 80
o
32.7 7,900 55.3 5,700 66.9 3,700
o o
75 39.6 12,300 51.0 10,000 57.3 8,000 75 49.6 7,900 70.2 5,200 80.3 3,700
70o 53.2 11,400 63.2 8,800 68.6 7,400 70o 65.8 7,100 84.2 4,700 92.5 3,600
o o
65 65.0 7,200 73.9 6,200 78.8 6,000 65 78.8 4,600 96.7 4,000 104.0 3,500
o
60 75.6 4,500 83.9 4,000 88.1 4,000 60o 90.7 2,700 107.0 2,400
55o 85.6 2,700 93.5 2,500 96.9 2,500
ON OUTRIGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED
0 lbs COUNTERWEIGHT, 360o ROTATION
Boom 117.7' (35.87m) Boom (telescoping mode II ) + Boom 117.7' (35.87m) Boom (telescoping mode II ) +
Angle 32.5' (9.9m) Jib Angle 58.1' (17.7m) Jib
o
in 3.5 Tilt 25o Tilt 45o Tilt in 3.5o Tilt 25o Tilt 45o Tilt
Degree R W R W R W Degree R W R W R W
80o 27.0 11,000 39.3 10,300 46.5 8,300 80
o
34.1 6,300 56.7 5,700 67.9 3,700
o
75 41.4 11,000 52.2 9,300 58.4 7,700 75o 50.8 6,300 71.5 5,100 81.3 3,700
o o
70 55.3 10,600 64.5 8,000 69.6 6,900 70 66.8 6,300 84.7 4,400 93.2 3,600
65o 67.3 8,600 75.9 7,000 80.0 6,200 65o 81.0 5,300 97.2 3,900 104.0 3,300
60o 78.2 6,400 86.2 5,700 89.6 5,500 60o 93.7 4,100 109.0 3,500 113.0 3,000
o o
55 87.7 4,500 95.0 4,100 97.8 4,100 55 105.0 2,800 120.0 2,500 126.0 2,400
50o 96.6 3,200 103.0 3,000 105.0 3,000 50o 115.0 1,800 130.0 1,700 137.0 1,600
45o 105.0 2,300 112.0 2,100 113.0 2,200
40o 113.0 1,500 119.0 1,500
R: Load radius in feet
W: Rated lifting capacity in pounds
15
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS MID EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED
15,700lbs COUNTERWEIGHT, 360o ROTATION
A 37.7 51 64.4 (19.62m) 91 (27.75m) 117.7 (35.87m) 131 144.4
B C (11.5m) C (15.56m) C C C C C C C (39.93m) C (44.0m)
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MID EXTENDED 15' 9'' (4.8m) SPREAD,
15,700lbs COUNTERWEIGHT, SPREAD 360o ROTATION, FRONT JACK EXTENDED
A 37.7' 51 64.4 64.4 91
E B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m)
0 31.7 20,400 45.0 7,800 58.3 2,100 58.3 6,800 84.7 2,400
Telescoping
mode I ,II I I II II
NOTE: ・The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-L) is based on the standard number of parts of line
listed in the chart.
・Standard number of parts of line for each boom length should be according to the following table.
Boom Length in 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top
Feet (meters) (11.5) (11.5 to 15.56) (15.56 to 19.62) (19.62 to 27.75) (27.75 to 44.0) Jib
Number of parts of
16 12 10 5 4 1
line
16
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS MID EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED
15,700lbs COUNTERWEIGHT, 360o ROTATION
Boom Boom
144.4' (44.0m) Boom + 32.5' (9.9m) Jib 144.4' (44.0m) Boom + 58.1' (17.7m) Jib
Angle Angle
o o o
in 3.5 Tilt 25 Tilt 45 Tilt in 3.5o Tilt 25o Tilt 45o Tilt
Degree R W R W R W Degree R W R W R W
80o 33.6 9,900 45.3 8,800 52.7 8,100 80o 40.6 5,900 65.3 5,400 74.7 3,400
75o 49.7 9,100 60.4 7,600 67.0 7,100 75o 60.0 5,800 82.6 4,800 90.1 3,400
70o 62.1 4,900 72.3 4,300 78.3 4,200 70o 73.8 2,800 94.8 2,500 103.0 2,300
ON OUTRIGGERS MID EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED
o
15,700lbs COUNTERWEIGHT, 360 ROTATION
Boom 117.7' (35.87m) Boom (telescoping mode I ) + Boom 117.7' (35.87m) Boom (telescoping mode I ) +
Angle 32.5' (9.9m) Jib Angle 58.1' (17.7m) Jib
in 3.5o Tilt 25o Tilt 45o Tilt in 3.5o Tilt 25o Tilt 45o Tilt
Degree R W R W R W Degree R W R W R W
80o 25.4 12,300 37.8 10,300 45.1 8,300 80o 32.7 7,900 55.3 5,700 66.9 3,700
75o 39.6 12,300 51.0 10,000 57.3 8,000 75o 49.6 7,900 70.2 5,200 80.3 3,700
70o 52.5 8,500 62.5 7,200 68.4 6,800 70o 64.9 5,500 84.0 4,500 92.5 3,600
65o 63.8 5,100 73.1 4,400 78.1 4,300 65o 77.3 3,000 95.0 2,600 103.0 2,400
60o 74.5 2,800 83.1 2,500 87.5 2,500
ON OUTRIGGERS MID EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED
15,700lbs COUNTERWEIGHT, 360o ROTATION
Boom 117.7' (35.87m) Boom (telescoping mode II ) + Boom 117.7' (35.87m) Boom (telescoping mode II ) +
Angle 32.5' (9.9m) Jib Angle 58.1' (17.7m) Jib
in 3.5o Tilt 25o Tilt 45o Tilt in 3.5o Tilt 25o Tilt 45o Tilt
Degree R W R W R W Degree R W R W R W
80o 27.0 11,000 39.3 10,300 46.5 8,300 80o 34.1 6,300 56.7 5,700 67.9 3,700
75o 41.4 11,000 52.2 9,300 58.4 7,700 75o 50.8 6,300 71.5 5,100 81.3 3,700
70o 55.4 10,300 64.5 8,000 69.6 6,900 70o 66.8 6,300 84.7 4,400 93.2 3,600
65o 66.1 6,800 75.3 6,000 79.7 5,700 65o 80.0 4,400 97.2 3,800 104.0 3,300
60o 76.7 4,600 85.0 4,100 88.7 4,000 60o 92.0 2,800 108.0 2,500 113.0 2,300
55o 86.3 3,100 94.0 2,800 97.3 2,800 55o 103.0 1,700 119.0 1,500 125.0 1,400
50o 95.5 2,000 103.0 1,800 105.0 1,800
45o 104.0 1,100 110.0 1,000 113.0 1,100
17
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS MID EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED
7,700lbs COUNTERWEIGHT, 360o ROTATION
A 37.7 51 64.4 (19.62m) 91 (27.75m) 117.7 (35.87m) 131 144.4
B C (11.5m) C (15.56m) C C C C C C C (39.93m) C (44.0m)
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MID EXTENDED 15' 9'' (4.8m) SPREAD,
7,700lbs COUNTERWEIGHT, 360o ROTATION
A 37.7' 51 64.4
E B (11.5m) B (15.56m) B (19.62m)
0 31.7 15,100 45.0 4,100 58.3 4,000
Telescoping
mode I ,II I II
NOTE: ・The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-L) is based on the standard number of parts of line
listed in the chart.
・Standard number of parts of line for each boom length should be according to the following table.
Boom Length in 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top
Feet (meters) (11.5) (11.5 to 15.56) (15.56 to 19.62) (19.62 to 27.75) (27.75 to 44.0) Jib
Number of parts of
16 12 10 5 4 1
line
18
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS MID EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED
3,700lbs COUNTERWEIGHT, 360o ROTATION
A 37.7 51 64.4 (19.62m) 91 (27.75m) 117.7 (35.87m) 131 144.4
B C (11.5m) C (15.56m) C C C C C C C (39.93m) C (44.0m)
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MID EXTENDED 15' 9'' (4.8m) SPREAD,
3,700lbs COUNTERWEIGHT, 360o ROTATION, FRONT JACK EXTENDED
A 37.7'
E B (11.5m)
0 31.7 12,300
Telescoping
mode I ,II
NOTE: ・The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-L) is based on the standard number of parts of line
listed in the chart.
・Standard number of parts of line for each boom length should be according to the following table.
Boom Length in 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top
Feet (meters) (11.5) (11.5 to 15.56) (15.56 to 19.62) (19.62 to 27.75) (27.75 to 44.0) Jib
Number of parts of
16 12 10 5 4 1
line
19
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS MID EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED
0 lbs COUNTERWEIGHT, 360o ROTATION
A 37.7 51 64.4 (19.62m) 91 (27.75m) 117.7 (35.87m) 131 144.4
B C (11.5m) C (15.56m) C C C C C C C (39.93m) C (44.0m)
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MID EXTENDED 15' 9'' (4.8m) SPREAD,
0 lbs COUNTERWEIGHT, 360o ROTATION, FRONT JACK EXTENDED
A 37.7'
E B (11.5m)
0 31.7 9,400
Telescoping
mode I ,II
NOTE: ・The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-L) is based on the standard number of parts of line
listed in the chart.
・Standard number of parts of line for each boom length should be according to the following table.
Boom Length in 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top
Feet (meters) (11.5) (11.5 to 15.56) (15.56 to 19.62) (19.62 to 27.75) (27.75 to 44.0) Jib
Number of parts of
16 12 10 5 4 1
line
20
TT-800XXL-1 RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS MIN EXTENDED 6' 9-7/8'' (2.08m) SPREAD,
o
360 ROTATION, FRONT JACK EXTENDED
Load 37.7' (11.5m) Boom
Radius Counterweight in pounds
in 15,700 7,700 3,700 0
Feet C C C C
10' 68 57,700 68 43,100 68 35,800 68 29,100
12' 65 41,500 65 30,200 65 24,700 65 19,500
15' 60 27,500 60 19,200 60 15,000 60 11,200
20' 50 15,400 50 9,600 50 6,700 50 4,000
25' 38 8,900 38 4,400 38 2,200
30' 21 4,900
D 0
o
38o/0o * 38o/0o * o o
50 /0 *
Telescoping conditions (%)
Telescoping
mode I ,II I ,II I ,II I ,II
2nd boom 0 0 0 0
3rd boom 0 0 0 0
4th boom 0 0 0 0
Top boom 0 0 0 0
NOTE: ・The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-L)
is based on the standard number of parts of line listed in the chart.
・Standard number of parts of line for each boom length should be according
to the following table.
Boom Length in 37.7'
Feet (meters) (11.5)
Number of parts of
16
line
21
WARNING AND OPERATING INSTRUCTIONS
FOR LIFTING CAPACITIES
GENERAL 10. When making lifts at a load radius not shown, use the next
1. RATED LIFTING CAPACITIES apply only to the machine as longer radius to determine allowable capacity.
originally manufactured and normally equipped by TADANO 11. Load per line should not exceed 12,300 lbs. (5,600kg) for
LTD. main winch and auxiliary winch.
Modifications to the machine or use of optional equipment 12. Check the actual number of parts of line with LOAD MOMENT
other than that specified can result in a reduction of capacity. INDICATOR (AML-L) before operation. Maximum lifting
2. Construction equipment can be hazardous if improperly capacity is restricted by the number of parts of line of LOAD
operated or maintained. Operation and maintenance of this MOMENT INDICATOR (AML-L). Limited capacity is as
machine must be in compliance with information in the determined from the formula, Single line pull for main winch
operation, safety and maintenance manual supplied with (12,300 lbs.) x number of parts of line.
machine. If these manuals are missing, order replacements 13. The boom angle before loading should be greater to account
through the distributor. for deflection. For rated lifting capacities, the loaded boom
3. The operator and other personnel associated with this angle and the load radius is for reference only.
machine shall fully acquaint themselves with the latest 14. The 37.7' (11.5m) boom length capacities are based on boom
American National Standards Institute (ANSI) safety fully retracted. If not fully retracted [less than 51'(15.56m)
standards for cranes. boom length], use the rated lifting capacities for the 51' (15.56m)
boom length.
SET UP 15. Extension or retraction of the boom with loads may be
1. Rated lifting capacities on the chart are the maximum attempted within the limits of the RATED LIFTING CAPACITIES.
allowable crane capacities and are based on the machine The ability to telescope loads is limited by hydraulic pressure,
standing level on firm supporting surface under ideal job boom angle, boom length, crane maintenance, etc.
conditions. Depending on the nature of the supporting 16. For lifting capacity of single top, reduce the rated lifting
surface, it may be necessary to have structural supports capacities of relevant boom according to a weight reductions
under the outrigger floats to spread the loads to a larger for auxiliary load handling equipment. Capacities of single top
bearing surface. shall not exceed 12,300 lbs. (5,600kg) including main hook.
2. For outrigger operation, outriggers shall be properly extended 17. When base jib or top jib or both jib removing, jib state switch
with tires free of supporting surface before operating crane. select removed.
The front jack must be properly extended. 18. When erecting and stowing jib, be sure to retain it by hand or by
3. When operating crane on outriggers fully retracted, do not other means to prevent its free movement.
exceed 71o maximum boom angle. Loss of backward stability 19. Use "ANTI-TWO BLOCK" disable switch when erecting and
will occur causing a backward tipping condition. stowing jib and when stowing hook block. While the switch is
pushed, the hoist does not stop, even when overwind condition
OPERATION occurs.
1. Rated lifting capacities have been tested to and meet 20. For boom length less than 144.4' (44.0m) and longer than
minimum requirements of SAE J1063-Cantilevered Boom 117.7' (35.87m) with jib, rated lifting capacities are determined
Crane Structures Method of Test. by loaded boom angle only in the column headed "144.4'
2. Rated lifting capacities do not exceed 85% of the tipping (44.0m) boom + jib".
load on outriggers fully extended as determined by SAE For boom length less than 117.7' (35.87m) with jib, rated lifting
J765-Crane Stability Test Code. capacities are determined by loaded boom angle only in the
Rated lifting capacities for partially extended outriggers are column headed "117.7' (35.87m) boom + jib". For angles not
determined from the formula, Rated Lifting Capacities shown, use the next lower loaded boom angle to determine
=(Tipping Load - 0.1 x Tip Reaction)/1.25. allowable capacity.
3. Rated lifting capacities above bold lines in the chart are 21. When lifting a load by using jib (aux. winch) and boom (main
based on crane strength and those below, on its stability. winch) simultaneously, do the following:
They are based on actual load radius increased by boom h Enter the operation status as jib operation, not as boom
deflection. operation.
4. The weight of handling device such as hook blocks, slings, h Before starting operation, make sure that mass of load is
etc., must be considered as part of the load and must be within rated lifting capacity for jib.
deducted from the lifting capacities. 22. Before telescoping the boom, set the telescoping mode
5. Rated lifting capacities are based on freely suspended loads selector switch to MODE I or MODE II with the boom
and make no allowance for such factors as the effect of wind, fully retracted. A change of the telescoping mode is not
sudden stopping of loads, supporting surface conditions, permissible when the boom has been partially or fully extended.
operating speeds, side loads, etc. Side pull on boom or jib
is extremely dangerous. DEFINITIONS
6. Rated lifting capacities do not account for wind on lifted load 1. Load Radius: Horizontal distance from a projection of the axis
or boom. Rated lifting capacities and boom length shall be of rotation to supporting surface before loading to the center of
appropriately reduced, when wind velocity is above 20 mph the vertical hoist line or tackle with load applied.
(9 m/sec.). 2. Loaded Boom Angle: The angle between the boom base
7. Rated lifting capacities at load radius shall not be exceeded. section and the horizontal, after lifting the rated lifting capacity
Do not tip the crane to determine allowable loads. at the load radius.
8. Do not operate at boom lengths, radii, or boom angle, where 3. Working Area: Area measured in a circular arc about the
no capacities are shown. Crane may overturn without any centerline of rotation.
load on the hook. 4. Freely Suspended Load: Load hanging free with no direct
9. When boom length is between values listed, refer to the external force applied except by the hoist line.
rated lifting capacities of the next longer and next shorter 5. Side Load: Horizontal side force applied to the lifted load either
booms for the same radius. The lesser of the two rated lifting on the ground or in the air.
capacities shall be used.
22
WARNING AND OPERATING INSTRUCTIONS
FOR USING THE LOAD MOMENT INDICATOR (AML-L)
1. When operating crane on outriggers: 3. During crane operation, make sure that the displays on front
h Set Stater switch to "ON" . panel are in accordance with actual operating conditions.
h Press the outrigger mode select key to register for the 4. The displayed values of LOAD MOMENT INDICATOR
outrigger operation. Press the set key, then the outrigger (AML-L) are based on freely suspended loads and make no
mode indicative symbol changes from flickering to allowance for such factors as the effect of wind, sudden
lighting. stopping of loads, supporting surface conditions, operating
h Press the boom mode select key to register the boom speed, side loads, etc.
mode, then the boom mode indicative symbol changes For safe operation, it is recommended when extending
from lighting to flickering. Each time the boom mode and lowering boom or swinging, lifting loads shall be
select key is pressed, the mode changes. Press the set appropriately reduced.
key to select the status that corresponds to the actual 5. LOAD MOMENT INDICATOR (AML-L) is intended as an aid
state of the boom, then the boom mode indicative symbol to the operator. Under no condition should it be relied upon
changes from flickering to lighting. to replace use of capacity charts and operating instruction.
h When erecting and stowing jib, select the status of jib Sole reliance upon LOAD MOMENT INDICATOR (AML-L)
set (jib state indicative symbol flicker). aids in place of good operating practice can cause an
2. A swing does not automatically stop even if the crane becomes accident. The operator must exercise caution to assure
overloaded. safety.
23
MEMO
24