Valve

D IR E C T IO N A L
CONTROL VALVES
H Y D R A U LIC C O M P O N E N T S
T E C H N I C A L C A T A L O G
CONTENT
POCLAIN HYDRAULICS Hydraulic components - Directional control valves
DIRECTIONAL CONTROL VALVES
Mechanically operated
MECHANICALLY OPERATED 5
2/2 way directional valves KVC (NG 6) 5
2/2 way directional valves KVC-NV (NG 6) 7
4/2, 4/3 way directional valves KV (NG 6, 10) 9
HYDRAULICALLY OPERATED (AUTOMATIC) 17

4/2 way automatic directional valves PKV (NG 6, 10)) 17
4/2 way automatic directional valves PKV-...-T (NG 6) 21
4/2, 4/3 way directional valves KV (NG 6, 10) 25
Hydraulically operated
ELECTRICALLY OPERATED 29
2/2 way directional valves KV (NG 6) 29
4/2, 4/3 way directional valve KV-5KO (NG 6) 40
4/2, 4/3 way directional valves type KV (NS 16) 53
4/2, 4/3 way directional proportional valve KVP (NG 6) 65
4/2, 4/3 way bankable directional valves KVM (NG 6) 69
4/2, 4/3 way bankable directional valves KVM (NG 6) 71
Vertical stacking for KVM valves 77
Check valve KVM-NOV-6 81
Throttle with check valve KVM-NDV-6 83
Pressure relief valve KVM-VV-6 87
Electrically operated
Vertical stacking on valves KVM

with standard sandwich valves to ISO 4401 (NG 6) 91
Auxiliary control lever 93
Inlet plate OB-KVM-6 (NG 6) 95
End plate ZB-KVM-6 101
Fixing elements for mounting 103
6/2 way directional valve KV (NG 6) 105
6/2 way directional valves KV-6K (NG 6) 117
6/2 way directional valves KVH (NG 6) 121
6/2 way directional valves KVH (NG 10) 125
6/3 Way directional valves KV (NG 4) 129
27/01/14 3
Directional control valves - Hydraulic components POCLAIN HYDRAULICS
4 27/01/14
MECHANICALLY OPERATED
2/2 way directional valves KVC (NG 6)
• NG 6
• Up to 250 bar [3 625 PSI]
• Up to 35 L/min [9.2 GPM]
KVC-2/2-K
Features Hydraulic symbol
Size 6
Flow rate L/min [GPM] 35 [9.2]
Operating pressure bar [PSI] 250 [3 625]
Viscosity range mm2/s [SUS] 15 to 380 [69.5 to 1 760]
Oil temperature range °C [°F] -20 to +70[-4 to 158]
Filtration ISO 4406-1999 19/17/14
Mass kg [lb] 1,2 [2.6]
Seal type NBR seals for mineral oil HL, HLP, to DIN 51524
P-Q Performance curves

Measured at 50°C [122°F] and viscosity of 32 mm2/s [148 SUS].
Diff. pressure
Flow
27/01/14 5
Dimensions
Stroke max.
Model code
K V C - 2 / 2 - K - -
*
Threaded connections
M12x1,5 No designation
G3/8 3/8
Special requirements to be briefly specified
6 27/01/14
2/2 WAY DIRECTIONAL VALVES KVC-NV (NG 6)
• NG 6
• Up to 210 bar [3 045 PSI]
KVC-2/2-NV-T
Size 6
Filtration ISO 4406-1999 19/17/14
Mass kg [lb] 1,2 [2.6]

Diff. pressure
Flow
27/01/14 7
Dimensions
Stroke max.
Model code
K V C - 2 / 2 - N V - T - -
*
G3/8 3/8
8 27/01/14
4/2, 4/3 WAY DIRECTIONAL VALVES KV (NG 6, 10)
• NG 6, 10
• Up to 350 bar [5 076 PSI]
• Up to 60 L/min [15.8 GPM] for NG 6
• Connecting dimensions to ISO 4401.
KV-4/3-5KO-6-R, KV-4/3-5KO-10-R
Operation Hydraulic symbols

Directional valves type KV with direct mechanical operation by means of a lever control the
direction of the hydraulic fluid medium flow. Spool types
These directional valves consist of a housing (1), control spool (2), control mechanism (3),
and return spring (4). In 4/3-way directional valves the centre position of the control spool
is the neutral position. The change-over to one of the operating positions "a" or "b" is done
by moving the operating pin lever (5) in such a manner that its acts on the control spool (2)
so as to clear corresponding flow ways and establish relevant links between ports, A, B, P,
and T.
On ceasing to apply force to the control mechanism (3), the return spring (4) push the
control spool into the neutral position.
There are two types of operation:
1/ With control spool not held in the operating position (the control spool returns to neutral
position on ceasing to apply force to the control mechanism - type KV-../..-R).
2/ With control spool held (detent) in the operating position (the control spool remains in
the operating position on ceasing to apply force to the control mechanism lever - type
KV-../..-RA).
27/01/14 9
Features
Size 6 10
Flow rate L/min [GPM] 60 [15.8] 100 [26.4]
P, A, B bar [PSI] 350 [5 076]
Operating pressure
T bar [PSI] 160 [2 320]
Viscosity range mm2 /s [SUS] 15 to 380 [69.5 to 1 760]
Oil temperature range °C [°F] -20 to+70 [-4 to 158]
Filtration NAS 1638 8
Mass kg [lb] 2,05 [4.52] 5,23 [11.53]
Mounting position Optional
Dimensions
Size 6 Size 10
3. Control mechanism on side ’’a’’ 3. Control mechanism on side ’’a’’

4/3 valves 4/3 valves
4/2 valves, spool types 51A 4/2 valves, spool types 51A
6. Fixing screws 4 pcs M5x30 to ISO 4762-10.9 6. Fixing screws 4 pcs M6x60 to ISO 4762-10.9
(by special order). (by special order).
Required tightening torque Md = 9 Nm. Required tightening torque Md = 15 Nm.
7. O-ring 9.25x1.78 7. O-ring 12.42x1.78
8. Valve cap. 8. Valve cap.
9. Nameplate. 9. Nameplate.
Required quality of the

mating surface.
10 27/01/14
Cartridge throttle
If flow rates greater than permissible occur during change-over, a cartridge
throttle must be fitted into P-line of the directional valve.
Size 6 Size 10 Throttle

Diff. pressure
Diff. pressure
Diff. pressure
Flow Flow Flow
Spool P-A P-B A-T B-T P-T
1 b,D b,D c,B c,C -
2 c,B c,B c,A c,A d,G
6 b,E b,E a,B a,B -
51A c,D b,D c,C a,B -
27/01/14 11
Model code
K V - 4 / - 5 K O - - - - - -
*
Number of spool position
2 2
3 3
Special requirements to be
briefly specified
Size
Size 6 6
Size 10 10
Control spool held Seal type

NBR seals for mineral oil HL,HLP
No designation
R to DIN 51524
FPM seals for HETG, HEES, HEPG
E
to VDMA 24568 and ISO 15380
RA
Spool type Throttle mm [in]

No designation Without throttle in P line
D08 Throttle Ø 0,8 [0.03 dia.]
1 D12 Throttle Ø 1,2 [0.05 dia.]
51A
12 27/01/14
6/2 WAY DIRECTIONAL VALVES KV (NG 6, 10)
• NG 6, 10
• Up to 350 bar [5 076 PSI]
• Threaded connections to ISO 9974 (Metric), ISO 1179 (BSPP/Gas).
KV-6/2-6-R..., KV-6/2-10-R...
Directional valves type KV with direct mechanical operation by means of a lever control the Spool types
direction of the hydraulic medium flow.
They are mostly used as link between two consumers and the basic directional valve,
when we want to control both consumers alternately by means of one basic directional
valve.
There are two types of operation:
1/ With control spool not held in the operating position (the control spool returns to position
’’a’’ on ceasing to apply force to the mechanism - type KV-../..-R).
2/ With control spool held (detent) in the operating position (the control spool remains in
the operating position on ceasing to apply force to the control mechanism lever - type KV-
../..-RA).
Mounting example
27/01/14 13
Features
Size 6 10
With YZ bar [PSI] 350 [5 076]
Operating pressure
Without YZ bar [PSI] 160 [2 320]
Viscosity range mm2/s [SUS] 15 to 380 [69,5 to1 760]
Oil temperature range °C [°F] -20 to +70 [-4 to158]
Mass kg [lb] 2,4 [5.3] 5,3 [11.7]
14 27/01/14
Dimensions
Size 6
Threaded connections M
A, B, C, D, P1, P2
Threaded LA=39,5 [1.55]( G3/8, M18x1,5)/37,5 [1.47] (G1/2, M22x1,5)

connection LC=23,5 [0.92] (G3/8, M18x1,5)/25,5[1.00] (G1/2, M22x1,5)
Size 10
A, B, C, D, P1, P2
Threaded 1. Housing.
connection 2. Control mechanism.
3. Valve cap.
4. Name plate.
27/01/14 15

Size 6 Size 10
Diff. pressure
Flow
Model code
K V - 6 / 2 - - - - - -
*
Size
Size 6 6
Size 10 10
Control spool held
RA
Threaded connections (M ; YZ)

M18x1,5; M14x1,5 No designation
M22x1,5; M14x1,5 M22
Size 6 G3/8; G1/4 G3/8
G1/2; G1/4 G1/2
3/4-16 UNF-2B; 9/16-18 UNF-2B SAE 8
M22x1,5; M14x1,5 No designation
M27x1,5; M14x1,5 M27
Size 10 G1/2; G1/4 G1/2
G3/4; G1/4 G3/4
7/8-14 UNF-2B; 9/16-18 UNF-2B SAE 10
Drainage
Without YZ No designation
With YZ YZ
Seal type
NBR seals for mineral oil HL,HLP to DIN 51524 No designation
FPM seals for HETG, HEES, HEPG to VDMA
E
24568 and ISO 15380
16 27/01/14
HYDRAULICALLY OPERATED (AUTOMATIC)
4/2 WAY AUTOMATIC DIRECTIONAL VALVES PKV (NG 6, 10) )
• NG 6, 10
• Up to 210 bar [3 045 PSI]
• Up to 60 L /min [15.8 GPM]
• Indirect hydraulic operation.
• Provision of pressure setting for change - over.
• Automatic change - over from the other operating position.
PKV-6, PKV-10
Operation Hydraulic symbol
Indirectly, hydraulic - operated directional valves type PKV are used to control the
hydraulic fluid flow direction by an automatic change - over.
Mounting example
Features
Size 6 10
Flow rate min/max L/min [GPM] 1/25 [0.3/6.6] 1/60 [0.3/15.8]
P, A, B bar [PSI] To 210 [3 045]
Operating pressure
T bar [PSI] To 40 [580]
Min. press. req. for autom. change over bar [PSI] 50 [725]
Change over pressure bar [PSI] 50 to210 [725 to3 045]
15 to 380 [69.5 to 1 760]

Viscosity range mm2/s [SUS]
Oil temperature range °C [°F] -20 to +70 [-4 to158]

Mass kg [lb] 2,6 [5.7] 3,2 [7.0]
27/01/14 17
Dimensions
Size 6
Connection diagram and

connecting dimensions to
ISO 4401
1. Emergency manual override
2. Setting elements with protectivecap
3. O-ring 9.25 X 1.78
4. Fixing screws: 4 pcs M5 x 45 to EN
ISO 4762-10.9 must be ordered
separately.
Tightening torque Md = 9Nm
5. Nameplate
Size 10
Connection diagram and 1. Emergency manual override

connecting dimensions to 2. Setting elements with protectivecap
ISO 4401 3. O-ring 12 X 2
4. Fixing screws: 4 pcs M6 x 55 to EN
ISO 4762-10.9 must be ordered
separately.
Tightening torque Md = 14Nm
5. Nameplate
Required quality of
the mating surface.
18 27/01/14
Size 6 Size 10
Pressure drop
Pressure drop
Flow Flow
Model code
P K V - - -
*
Size
Size 6 6
Size 10 10
Seal type
NBR seals for mineral oil HL, HLP, to DIN 51524 No designation
E
24568 and ISO 15380

27/01/14 19
20 27/01/14
4/2 WAY AUTOMATIC DIRECTIONAL VALVES PKV-...-T (NG 6)
• NG 6
• Up to 210 bar [3 045 PSI]
• Up to 30 L /min [7.9 GPM]
• Automatic, load - independent reversal.
• Predefined actuator direction at start - up.
PKV-6-T, PKV-6-T-G

These valves reverse the movement of an actuator every timethe flow through the valve
stops. Preferential starting is P  Band A  T position. The spool is moved by two springs PKV-6-T
andlocked by unbalanced pressure inside valve. When no moreflow is crossing the valve,
the spool changes the positioninverting the direction of the actuator. These valves are
mostlyused to control the movement compactors or system where it isnot possible to use
electrical device.
About the spindle for the PKV-6-T-G valves:
The spindle for the PKV-6-T-G valves is used just to set the system pressure limiter. To set PKV-6-T-G
the maximum pressure you have to block the self-reversing function.
Procedure to set a pressure on the system pressure limiter:
1/ Switch off the pump or reduce pressure to minimum (10 bar max).
2/ To set the system pressure limiter first block the automatic reversal of the valve.
Remove the dome nut and turn the offsetting spindle clockwise until it hits its inner end Mounting example
spool. The spool is now clamped P to B and A to T.
3/ Start the pump and set the required pressure.
4/ After that stop again the pump.
5/ Turn the offsetting spindle anticlockwise until it hits its outer end stop then put the dome
nut back.
Never turn the offsetting spindle when the valve is pressurized over
10 bar [145 PSI]. This can cause seal damage. If necessary switch off
the pump.
System
pressure
Offsetting limiter
spindle
Dome nut
Seal
27/01/14 21
Features
Size 6
Flow rate min/max L/min [GPM] 3/30 [0.8/7.9]
Operating pressure P, A, B bar [PSI] 50 to 210 [725 to 3 045]
Max. pressure T bar [PSI] 40 [580]
Viscosity range mm2 /s [SUS] 20 to 200 [92.7 to 926.8]
Oil temperature range °C [°F] -20 to +60 [-4 to 140]
PKV-6-T 1,3 [2.8]
Mass kg [lb]
PKV-6-T-G 1,4 [3.1]
Dimensions
Required quality of
the mating surface.
Connection diagram and connecting dimensions to ISO 4401.
Tightening torque
max. 2Nm
Spindle
PKV-6-T PKV-6-T-G
4 x fixing screws M5x30 to DIN EN ISO 4762-10.9 must be ordered separately.

Required tightening torque Md = 9 Nm [79.65 in.lbf].
22 27/01/14

Measured at 50°C [122°F] and
viscosity of 32 mm2/s [148 SUS].
Pressure drop
Flow
Model code
P K V - 6 - T - - -
*
Offsetting spindle
Without offsetting spindle No designation
With offsetting spindle G
Seal type
NBR seals for mineral oil HL, HLP to DIN 51524 No designation
E
24568 and ISO 15380

27/01/14 23
24 27/01/14
4/2, 4/3 WAY DIRECTIONAL VALVES KV (NG 6, 10)
• NG 6, 10
• Up to 350 bar [5 076 PSI]
• Up to 130 L/min [34.3 GPM]
• Direct hydraulically operation.

• Threaded connections to ISO 1179.
KV-4/3-5KO-6-H, KV-4/3-5KO-10-H
The KV-...-H is a hydraulically controlled 4/3 or 4/2 way directional control valve. The valve Spool types
is operated by the pilots ports X and Y via the connection of an external pilot pipe direct on
the valve body.
The minimum pilot pressure must be ensured for all operating conditions of the directional
valve.
Features
Size 6 10
Ports A, B, P bar [PSI] 350 [5 076]
Operating pressure
Ports X, Y, T bar [PSI] 210 [3 045]
Pilot supply pressure min. bar [PSI] 10 [145]

2 15 to 380 [69.5 to 1 760]
Viscosity range mm /s [SUS]
Mass kg [lb] 1,4 [3.1] 4,0 [8.8]
27/01/14 25
Dimensions
Size 6 Size 10
1. Threaded connection X (Y) - G1/4 1. Threaded connection X (Y) - G1/4

2. Fixing screws 4 pcs M5x30 to ISO 2. Fixing screws 4 pcs M6x60 to ISO
4762-10.9 (by special order) Required 4762-10.9 (by special order) Required
tightening torque Md = 9Nm tightening torque Md = 15Nm
3. O-ring 9.25 x 1.78 3. O-ring 12.42 x 1.78
4. Nameplate. 4. Nameplate.

mating surface.
Cartridge throttle
If flow rates greater than permissible occur during change-over, a cartridge

throttle must be fitted into P-line of the directional valve.
26 27/01/14

Size 6 Size 10
Diff. pressure
Diff. pressure
Flow Flow
Spool P-A P-B A-T B-T P-T Spool P-A P-B A-T B-T P-T
1 8 8 6 6 - 1 1 1 5 5 -
2 5 5 4 4 1 2 3 3 2 7 8
6 5 5 9 9 - 6 1 1 2 2 -
51A 5 5 1 1 - 51A 1 1 3 3 -
Model code
K V - 4 / - 5 K O - - H - - -
*
Number of control spool position
Two positions 2
Three positions 3
Size
Size 6 6 Special requirements to be
Size 10 briefly specified
10
Spool types
Seal type
1
NBR seals for mineral oil
No designation
HL,HLP to DIN 51524
(NS10) 2 FPM seals for HETG, HEES,
E HEPG to VDMA 24568 and
ISO 15380
(NS 6) 2
51A
Throttle mm [in]
51B
No designation Without throttle in P line
27/01/14 27
28 27/01/14
ELECTRICALLY OPERATED
2/2 WAY DIRECTIONAL VALVES KV (NG 6)
• NG 6
• Up to 210 bar [3045 PSI]
• Direct in-line mounting.
• Threaded connections to ISO 1179 (BSPP/Gas), ISO 11926 (UNF).
• Hermetically sealing at closed flow path.
• No STICK-SLIP effect even after a prolonged dwell time under pressure.
• Plug-in solenoid connector to ISO 4400.
• Protection of solenoid IP65 to EN 60529 / IEC 60529.
• Fulfil EMC (89/336/EEC).
KV-2/2-6-S-..

Directly-operated directional seat valves KV are used forthe control of direction of
hydraulic fluid.
KV-2/2-6-S-A-...
In the start control position a, the return spring (4) holds the ball(2) in its open position, thus
freeing the flow path betweenports A and B. The change-over into the control position b
isaccomplished by energizing the solenoid (3), whereby the ball(2) is pushed against the
seat (1). The hydraulic fluid on port Ais under pressure.
KV-2/2-6-S-B-...
The hydraulic fluid on port A in the start control position a isunder pressure. The return
spring (4) pushes the ball (2)against its seat (1). The change-over to the control position
bis performed by energizing the solenoid (3), thus freeing theflow path between ports
A and B.
The change-over can also be done manually by pressing theemergency manual Mounting example
override (5).
27/01/14 29
Features
Hydraulic
Size 6
Flow rate L/min [GPM] 30 [7,93]
Operating pressure bar [PSI] 210 [3045,79]
Oil temperature range °C [°F] -20 to +70 [-4 to +158]
Viscosity range mm2/s [SUS] 15 to 380 [3.24 to 82]
Mass kg [lb] 2,2 [4,85]
Electrical
Supply voltage V 12, 24, 48, 110, 230 DC or AC
Power W 29 *
Intermittence continuous
Ambient temperature °C [°F] To +50 [To +122]
Coil temperature °C [°F] To +180 [To +356]
Duty cycle min-1 250
* 12V supply voltage - 36W
Dimensions
KV-2/2-6-S-A-
3. Solenoid ’’b’’ MR-045.

5. Emergency manual override.
6. Nameplate.
KV-2/2-6-S-B-
30 27/01/14
Measured at 50°C [122°F] and viscosity of 32

mm2/s [148 SUS].
Valid for flow direction A to B.

Symbol A
Pressure drop
Symbol B
Flow
Model code
K V - 2 / 2 - 6 - S - - - -
*
Manual override option
Emergency manual override No designation
Manual override with rubber cover G briefly specified
Lockable manual override C
Spool type
Seal type
NBR seals for mineral oil HL,
A No designation
HLP, to DIN 51524
FPM seals for HETG, HEES,
B ISO 15380
Supply voltage Threaded connections

Direct voltage Alternating voltage G 3/8
No designation
12 V 12 DC 12 AC SAE 8 3/4-16 UNF-2B
24 V No designation 24 AC
48 V 48 DC 48 AC
110 V 110 DC 110 AC
220 V 220 DC - Overvoltage protection
230 V - 230 AC* No designation overvoltage protection
T With overvoltage protection

- Alternating voltage solenoids are fitted with a bridge rectifier
-With solenoids of over 48 V an earthing clampto ISO 4400 must be
connected.
To fulfil EMC (89/336/EEC) a capacitor must be built in.
Connector type
EN 175301-803 without signal lamp No designation
EN 175301-803 with signal lamp L
EN 175301-803 without connector K
AMP junior timer without connector M
Deutsch V
27/01/14 31
32 27/01/14
3/2 WAY DIRECTIONAL VALVES KVC (NG 4)
• NG 4
• Up to 160 bar [2 320 PSI]
• Plug-in connector for solenoids to ISO 4400.
• Optimized flow paths for low losses of pressure.
• Wet pin solenoid with interchangeable coil.
• Manual emergency control.
• Protection of solenoid IP 65 to EN 60529 / IEC 60529.
KVC2-3/2-4-47B, KVC-3/2-4-47B
Hydraulic Single: KVC-3/2-4-47B

Size 4
Viscosity range mm2/s [SUS] 15 to 380 [69.5to 1760]
Oil temperature range °C [°F] -20 to+70 [-4 to 158] Double: KVC2-3/2-4-47B
Filtration ISO 4406-1999 19/17/14
KVC-3/2-4 1,6[3.5]
Mass kg [lb]
KVC2-3/2-4 3,5 [7.7]
Electrical
Supply voltage V 12, 24
Power W 29 *
Switch-on time** ms 50 to 80
Switch-off time** ms 30 to 55
Switching frequency 1/h 15 000
Ambient temperature °C [°F] to50 [122]
Coil temperature °C [°F] to 180 [356]
Duty cycle Continuous
* 12 V supply voltage - 36 W.
** The switching-on and off times apply to 24 V DC solenoids
27/01/14 33

KVC-3/2-4 KVC2-3/2-4
Diff. pressure
Diff. pressure
Flow Flow
Dimensions
KVC-3/2-4-47B KVC2-3/2-4-47B
Emergency manual override Emergency manual override
34 27/01/14
Model code
K V C - 3 / 2 - 4 - 4 7 B - - - -
*
Hydraulic symbol
Simple No designation
Double 2
Special requirements to
be briefly specified
Working ports
Three working ports 3

Two positions 2 Seal type
NBR seals for mineral oil
No designation
HL,HLP to DIN 51524
Size
PM seals for HETG,
Size 4 E HEES, HEPG to VDMA
24568 and ISO 15380
Spool type
Supply voltage
Direct voltage 24V 24 DC

Emergency manual
No designation
override
Connector type Manual override with
G rubber cover
C Lockable manual override
AMP Junior timer without connector M
Deutsch V
Overvoltage
Without overvoltage protection No designation
With overvoltage protection T
Threaded connections A, B, P
M14x1,5; - No designation
G1/4 ; - 1/4
9/16-18 UNF-2B ; 9/16-18 UNF-2B SAE 6
27/01/14 35
36 27/01/14
3/2 WAY DIRECTIONAL VALVES KVC (NG 10)
• NG 10
• Up to 350 bar [5 076 PSI]
• Up to 100 L/min [26.4 GPM]

• Threaded connections to ISO 9974 (Metric), ISO 1179 (BSPP/Gas), ISO 11926 (UNF).
KVC-3/2-10

Directional valves type KVC-3/2-10 with direct solenoid operation are used to control the
direction of hydraulic fluid flow.
Type KVC-3/2-10 is a reduced version of type KV-6/2. It is used for alternate control of two
one-pipe working units (e.g. Plunger) with common, main directional valve.
It is also very proper as bypass valve.
The change-over can also be done manually by pressing the emergency manual override.
B
P Mounting example
27/01/14 37
Features
Hydraulic
Size 10
Without drainage 60 [15.8]
Flow rate L/min [GPM]
With drainage 100 [26.4]
Without drainage 250 [3 625]
Operating pressure bar [PSI]
With drainage 350 [5 076]
Oil temperature range °C [°F] -20 to +70 [-4 to+158]
Without drainage 5,6 [12.34]
Mass kg [lb]
With drainage 7,1 [15.65]
Electrical
Supply voltage V 12, 24 DC
Power W 45
Switching frequency 1/h 15000
Ambient temperature °C [°F] to +50 [to +122]
Coil temperature °C [°F] to +180 [to +356]
Dimensions
[0.59]
15
L7 B Dimensions Without YZ With YZ

L4 11 ±0.2 L 201 [7.91] 210 [8.27]
Pg 9
[0.43 ±0.01dia.] z=2 L1 85 [3.34] 94 [3.70]

P
L2 29,5 [1.16] 31,5 [1.24]
H
A L3 55,5 [2.18] 62,5 [2.46]

L4 42,5 [1.67] 47 [1.85]
L5 19,5 [0.76] 18 [0.71]
H1
L6 46 [1.81] 40 [1.57]
H5
L7 - 79,5 [3.13]
H 104 [4.09] 105 [4,13]
H4
YZ
H1 67 [2.63] 74 [2,91]
H2 73 [2,87] 90 [3,54]
6.6 L5 L6 ±0.2 [L6 ±0.01] 108 [4.25]
[0.26 dia.] H3 46 [1,81] 66 [2,60]
L1 122 [4.80] (with manual override)
H4 - 33 [1,30]
L H5 50,5 [1,98] 31 [1,22]
9 8 7 3 6 5
L3
B 3. Solenoid "b" MR-060
P 6. Plug-in connector "b" -black
7. Fixing screws:
]
-without YZ: 2 x M6x60 to ISO 4762-10.9

±0.01
-with YZ: - 2 x M6x40 to ISO 4762-10.9

H3 ±0.2 [H3
H2
8. Nameplate
9. Valve cap
L2 A Threaded connection
z=3
38 27/01/14
Without YZ With YZ
Pressure drop
Flow
Model code
K V C - 3 / 2 - 10 - - 41B - - - - -
*

Emergency manual override No designation briefly specified
Manual override with rubber cover G
Spool type Seal type

No designation
41B HLP to DIN 51524
ISO 15380
Supply voltage
Direct voltage 24V No designation
Direct voltage 12V 12 DC Drainage
No designation Without YZ
Connector type
175301-803 without signal lamp No designation
YZ With YZ

Deutsch V
Threaded connections A,B,P ; YZ

No designation M18x1,5 ; -
Overvoltage M22 M22x1,5 ; -
M20 M20x1,5 ; -
With overvoltage protection T 3/8 G3/8; -
1/2 G1/2; -
3/4 G3/4; -
3/4 G3/4; G1/4
SAE 12 1 1/16-12 UNF-2B ; 9/16-18 UNF-2B
27/01/14 39
4/2, 4/3 WAY DIRECTIONAL VALVE KV-5KO (NG 6)
• NG 6
• Up to 350 bar [5 076 PSI]
• Connection diagram and connecting dimensions to ISO 4401.

• 5-chamber model with good spool guidance.
• Adjustment of the switching time.
KV-4/3-5KO-6
Directional valves type KV with direct solenoid operation control the direction of the hydraulic Spool types
medium flow.
These directional valves consist of a housing (1), a control spool (3), and one solenoid (2) with
two return springs (4) in 4/2-way directional valves, and two solenoids (2) with two return
springs (4) in 4/3-way directional valves. In 4/3-way directional valves the centre position of the
control spool is the neutral position. The change-over to the operating position (a) and (b) is
done by energizing the solenoids (2) "a" and "b" respectively, whereby the solenoid plunger
acts on the control spool (3) via the operating pin (5), thus clearing the corresponding flow ways
and establishing relevant links between ports A, B, P, and T.
When the solenoid (2) is de-energized, the control spool (3) is returned to its neutral position by
the return spring (4). The change-over can be done manually by pressing the emergency
manual override (6).
KV-4/2-5KO-6-81
Directional valve with two operating position, two solenoids without springs allow the control
spool to be held in the operating position (detent). The control spool remains in the operation
position also when the solenoids are de-energized.
40 27/01/14
Features
Hydraulic
Size 6
Flow rate L/min [GPM] see P-Q curves
Operating pressure
Port T bar [PSI] 250 [3 625]
4/2 1,9 [4.2]
Mass kg [lb]
4/3 2,7 [5.9]
Electrical
Direct 12, 24, 48
Supply voltage V
Alternating 110, 230
Power W 29 *
Switch-on time** ms 50 to 80
Switch-off time** ms 30 to 55
Ambient temperature °C [°F] to 50 [122]
Coil temperature °C [°F] to180 [356]
** The switching-on and off times apply to 24 V DC solenoids.
P-Q Performance curves P-Q Operating limits

2
Measured at 50°C [122°F] and viscosity of 32 mm /s [148 SUS]. Measured at 50°C [122°F] and viscosity of 32 mm2/s [148 SUS].
Diff. pressure
Diff. pressure
Flow
Flow
The operating limits of the valve are
determined at a voltage 10% below
the nominal rating. The curves refer
Flow path Spool Kurve to application with symetrical flow
Spool P-A P-B A-T B-T P-T 1 throw the valve (P-A and B-T). In the
1 case of asymetric flow (e.g. one part
1 8 8 6 6 - 2 4 not used) reduced values may result.
2 5 5 4 4 1 3 3
Note: For valves with adjustment of
3 8 8 7 7 - 6 3 the switching time reduced values of
6 the operating limits may result.
5 5 9 9 - 81 1
81 5 5 1 1 - 51A, 51B 1
51A, 51B 5 5 1 1 - 41A, 41B 2
41A, 41B 7 7 - - -
27/01/14 41
Dimensions
With hand operation - add

letter G before spool type in
ordering code.
KV-4/2-5KO-6
Max. torque 30 Nm
Max. torque Connection diagram and

connecting dimensions to
ISO 4401.
KV-4/3-5KO-6
Max. torque 30 Nm

Max. torque
mating surface.
KV-4/2-5KO-6-81
Cartridge throttle
If flow rates greater than permissible occur during change-over, a

cartridge throttle must be fitted into P-line of the directional valve.
Installation
The directional control valve must be installed horizontally (Nameplate on top). If this is not the case, the valve must be removed for venting.
Unscrew the vent screw. Move the spool alternately to the switching positions a and b until no more bubbles appear at the screw hole. The oil
must be visible at the screw hole. Missing oil should be refielled with an oilcan, drop by drop. Screw in the vent screw.A constant or short time
static oil pressure of at least > 4 bar must prevail at connection T of the directional control valve to maintain the oil pressure in the spring
chambers. If this is not the case, the preloaded oil volume of the restricted valve would leak into the T channel through the leakage section of the
control spool shoulders.The dampening constancy also depends on the constancy of the oil viscosity.
For this reason the dampening effect should always be adjusted with the system at operational temperature.
42 27/01/14
Function drawing
KV-4/3-5KO-6
(KV-4/2-5KO-6)
KV-4/2-5KO-6-81
Vent screw
KV-4/3-5KO-6-2
Vent screw
1. Solenoid "a" - MR-045

2. Solenoid "b" - MR-045
3. Fixing screws 4 pcs M5 x 30 to ISO 4762
-10.9 must be ordered separately.
Required tightening torque Md = 9 Nm
Vent screw 4. Plug-in connector "a" - grey
5. Plug-in connector "b" - black

KV-4/2-5KO-6-UD 6. Emergency manual override
7. O-ring 9,25 x 1,78
8. Valve cap
9. Nameplate
10. Constant action restrictor
27/01/14 43
Model code
K V - / - 5 K O - 6 -
Working ports
Four working ports 4
Number of control spool positions

Two positions 2
Three positions 3

Spool types
1 1A 1B 81
2 2A 2B
3 3A 3B
6 6A 6B
51A 51B
41A 41B
Port T in the valves with spool type 41A and 41B to be used as lekage line.
Valves with adjustment of the switching time - a constant or short - time static
oil pressure of at least  4 bar [58 PSI] must prevail at connection T of the
directional control valve to maintain the pressure in the spring chambers.
44 27/01/14
- - - - -
*
Supply voltage
Direct voltage Alternating voltage
12 V 12 DC 12 AC
48 V 48 DC 48 AC
110 V 110 DC 110 AC
230 V 230 DC 230 AC*
Alternating voltage solenoids are fitted with a bridge rectifier

With solenoids of over 48 V an earthing clampto ISO 4400 must
be connected
*To fulfil EMC (89/336/EEC) a capacitor must be built in.
Connector type
Deutsch V
Overvoltage protection
Throttle mm [in]
Without throttle in P line No designation
Throttle Ø 0,8 [0.03 dia.] D08
Constant action restrictor

Without restrictor No designation
With restrictor Ø 0,35 [0.01 dia.] UD
Seal type
NBR seals for mineral oil HL,HLP to
No designation
DIN 51524
FPM seals for HETG, HEES, HEPG to
E
VDMA 24568 and ISO 15380
27/01/14 45
• NG 10
• Up to 350 bar [5 076 PSI].
• Up to 120 L/min [31.7 GPM].

• Plug-in connector for solenoids to ISO 4400.5-chamber model with good spool guidance.
• Adjustment of the switching time.
KV-4/3-5KO-10
Directional valves type KV with direct solenoid operation control the direction of the hydraulic Spool types
medium flow.
These directional valves consist of a housing (1), a control spool (3), and one solenoid (2) with
two return springs (4) in 4/2-way directional valves, and two solenoids (2) with two return
springs (4) in 4/3-way directional valves. In 4/3-way directional valves the centre position of the
control spool is the neutral position. The change-over to the operating position (a) and (b) is
done by energizing the solenoids (2) "a" and "b" respectively, whereby the solenoid plunger
acts on the control spool (3) via the operating pin (5), thus clearing the corresponding flow
ways and establishing relevant links between ports A, B, P, and T.
When the solenoid (2) is de-energized, the control spool (3) is returned to its neutral position
by the return spring (4). The change-over can be done manually by pressing the emergency
manual override (6).
KV-4/2-5KO-10-81
Directional valve with two operating position, two solenoids without springs allows the control
spool to be held in the operating position (detent). The control spool remains in the operation
position also when the solenoids are de-energised.
1 3 4 5 2 6
A B
T A P B T
46 27/01/14
Features
Hydraulic
Size 10
Operating pressure
Port T bar [PSI] 250 [3 625]
Oil temperature range °C [°F] -20 to+70 [-4 to 158]
Mass 4/2 6,5 [14.3]
kg [lb]
4/3 7,3 [16.1]
Mounting position Optiona
Electrical
Direct 12, 24, 48
Supply voltage V
Power W 45
Switch-on time* ms 70 to 95
Switch-off time* ms 40 to 80
* The switching-on and off times apply to 24 V DC solenoids.

Measured at 50°C [122°F] and viscosity of 32 mm2/s [148 SUS]. Measured at 50°C [122°F] and viscosity of 32 mm2/s [148 SUS].
Diff. pressure
Pressure
Flow
Flow
Flow path Spool curve The operating limits of the valve are
Spool P-A P-B A-T B-T 1 1 determined at a voltage 10% below the
1 1 1 5 5 - 2 4 nominal rating. The curves refer to
2 3 3 2 7 8 3 5 application with symetrical flow throw the
valve (P-A and B-T). In the case of
3 6 6 3 4 - 6 3 asymetric flow (e.g. one part not used)
6 1 1 2 2 - 9 6 reduced values may result.
9 6 6 2 2 - 81 1
Note: For valves with adjustment of the
81 1 1 3 3 - 51A, 51B 1
switching time reduced values of the
51A, 51B 1 1 3 3 - 41A, 41B 2 operating limits may result.
41A, 41B 6 6 - - -
27/01/14 47
Dimensions
122 [4.80]
0.04]
T T
[2.44 dia.]
46 [1.81]
62
[2.76
KV-4/2-5KO-10
A B
P
70
With hand operation - add letter G

24.5 54 [2.13] before spool type in ordering code.
Max. torque 6 Nm [0.96]
ca. 219[8.62]
.Connection diagram and connecting
dimensions to ISO 4401.
ø 11[0.43 dia.]
A B
ca. 112 [4.41]
50.5 [1.99]
83 [3.27]
KV-4/3-5KO-10
ø 6.6 [0.26 dia.] S=27 [1.06]

ca. 108 [4.25] 103 [4.06] Max. torque 50 Nm
ca. 319[12.56]
A B
Pg9.
KV-4/2-5KO-10-81
17.5 S=27 [1.06]

[0.69] ca. 336.5 [13.23] Max. torque 50 Nm
0,01/100mm
Rmax4 Required quality of the

mating surface.
Cartridge throttle

Installation
The directional control valve must be installed horizontally (Nameplate on top). If this is not the case, the valve must be removed for venting.
Unscrew the vent screw. Move the spool alternately to the switching positions a and b until no more bubbles appear at the screw hole. The oil
must be visible at the screw hole. Missing oil should be refielled with an oilcan, drop by drop. Screw in the vent screw.A constant or short time
static oil pressure of at least > 4 bar must prevail at connection T of the directional control valve to maintain the oil pressure in the spring
chambers. If this is not the case, the preloaded oil volume of the restricted valve would leak into the T channel through the leakage section of the
control spool shoulders.The dampening constancy also depends on the constancy of the oil viscosity.For this reason the dampening effect
should always be adjusted with the system at operational temperature.
48 27/01/14
Function drawing
4 1 9 7 3 8 2 5 6
KV-4/3-5KO-10
A B (KV-4/2-5KO-10)
1. Solenoid "a" - MR-060 4. Plug-in connector "a" - grey

2. Solenoid "b" - MR-060 5. Plug-in connector "b" - black
3. Fixing screws 4 pcs M6 x 60 to ISO 6. Emergency manual override
4762 -10.9 must be ordered separately. 7. O-ring 12,42 x 1,87
Required tightening torque Md = 15 Nm 8. Valve cap
9. Nameplate
10. Constant action restrictor
KV-4/2-5KO-10-81
A B
Vent screw
KV-4/3-5KO-10-2-UD
A 10 B (KV-4/2-5KO-10-2-UD)
27/01/14 49
Model code
K V - / - 5 K O - 10 -
Working ports

Two positions 2
Three positionsTwo positions 3

Manual override with rubber cover
G
Spool types
1 1A 1B 81
2 2A 2B
3 3A 3B
6 6A 6B
51A 51B
41A 41B
Port T in the valves with spool type 41A and 41B to be used as lekage line.
Valves with adjustment of the switching time - a constant or short - time static oil pressure
of at least > 4 bar [58 PSI] must prevail at connection T of the directional control valve to
maintain the pressure in the spring chambers.
50 27/01/14
- - - - -
*
Supply voltage
12 V 12 DC 12 AC
48 V 48 DC 48 AC
110 V 110 DC 110 AC
230 V 230 DC 230 AC*
- Alternating voltage solenoids are fitted with a bridge rectifier

- With solenoids of over 48 V an earthing clamp to ISO 4400 must
be connected
*To fulfil EMC (89/336/EEC) a capacitor must be built in.
Connector type
Deutsch V
Throttle mm [in]
Constant action restrictor

Without restrictor No designation
With restrictor Ø 0,35 [0.01 dia.] UD
Seal type
No designation
DIN 51524
E
27/01/14 51
52 27/01/14
4/2, 4/3 WAY DIRECTIONAL VALVES TYPE KV (NS 16)
• NG 16
• To 350 bar [5 076 PSI]
• To 300 L/min [79 GPM]
• Indirect, solenoid, and mechanical (by lever) operation.
• Plug-in solenoid connector to ISO 4400.
KV-4/3-16-

Directional valves type KV with indirect, solenoid-hydraulic operation control the hydraulic
fluid flow direction. Spool types
These valves consist of the main valve (1), a control spool (2), two return springs (3) in
4/3-way valves and none in 4/2-way valves, a double throttle check/valve (4) and a
pilot valve (5).
The pilot valve (5) is connected with the pressure chambers (8) via the pilot line (7).
Feeding of the pilot valve oil is either or external (via the port "x"). Change-over of the
control spool to one of the operating position is activated by the introduction of oil via the
pilot valve (5) into one of the pressure chambers (8). A pressure rise in chambers provokes
the movement of the control spool (2). Suitable links between ports A,B,P,T according to
spool types are established as set forth in the table.
When the solenoid of the pilot valve (5) are de-energized a link between the pressure
chamber (8) and the return line "y" for the pilot oil discharge is established. A pressure
drop in the chamber actuates the main valve return spring (3) which automatically return
the control spool to the neutral position.
Dischange of the return pilot oil from the pressure chambers is either internal or external
(via the port "y").
Manual change-over of the main valve is also possible by pressing the emergency manual
override (9).
Indirect directional valves can also be provided with a manual pilot valve. These valves are
manually operated by moving the operating lever.
27/01/14 53
Features
Flow rate l/min [GPM] 300 [79.2]

Ports A, B, P 350 [5076.3]
Operating pressure bar[PSI]
Port T 250 [3625.9]
Pilot oil pressure (x-external) bar [PSI] 50-250 [725.2-3625.9]
In valve types with internal pilot oil supply (x) the
spool types 2, 3, and 4 are possible only when the oil
Pilot oil pressure (x-internal) flow in the direction from P towards T achieves the
Pre-load valve is fitted into P-port of the main valve
Without Pre-load valve in the P-port of the main valve flow rate
Q = 150 L/min [39.6 GPM], with the control spool in
the centre position.
Oil temperature range °C [°F] -20 to +70 [-4 to 158]
Viscosity range mm2/S 15 to 380
3 7,8 [0.47]
Required pilot oil volume cm [cu.in] 2 positions valve
3 positions valve 3,9 [0.24]
Main valve 8 [17.6]
4/3 pilot valve 2,5 [5.5]
Mass Kg [lb] 4/2 pilot valve 2,2 [4.8]

Throttle/check valve 1,45 [3.2]
Pressure reducing 1,70 [3.7]
valve
Mounting position Optional, horizontal for spool types 4/2
Switch-on time 3 positions valve 60
(ms)
Solenoid change-over from the operating to the centre position 2 positions valve 85
Switch-off time 3 positions valve 45
(ms)
Solenoid change-over from the operating to the centre position 2 positions valve 50
Ambient temperature range °C [°F] +50 [122]
Coil temperature range °C [°F] +180 [356]
Power W 29 (12V supply voltage - 36W)
Voltage V 12, 24, 48, 110, 230
The switch-on and switch-off times apply to 24 V DC solenoids.

Throttle
Diff. pressure
Diff. pressure
Flow Flow
Spool type P-A P-B A-T B-T P-T

1, R1, 51B, 51A, F51, R51 e e e f -
2, R2 a b c e f See Model Code for
3, R3 b b c d - spool type choice.
4, R4 b c c e -
5, R5 b c c e -
6, R6 b c d e -
54 27/01/14
Cartridge throttle Pre-load valve
Pilot valve In valves with a low pressure bypass

If the pilot oil supply rate (x) is greater than and internal pilot oil feed, minimum
permissible a cartridge throttle shall be pilot pressure is obtained by installing
fitted into the P line of the directional valve. a pre-load valve in the P-port of the
main valve.
The cracking pressure is approx.
4,5 to 6 bar [65 to 87 PSI].
Main valve
Pressure reducing valve Throttle check valve

The pressure reducing valve used when the pilot oil "X" pressure The throttle check valve used for setting the supply flow rate of the
exceeds the permissible limit p = 250 bar [3 626 PSI]. pilot oil to the pressure chambers. Simultaneously, the change-
over speed of the main control spool is adjusted. In this way a
smoother change-over, without hydraulic shocks is provided.
Dimensions
Manual override
1. Main valve
4. Throttle / check valve
5.1 4/3 pilot valve
5.2 4/2 pilot valve
10. Control mechanism
11. Pressure reducing valve
14.1 Solenoid "a" MR-045
14.2 Solenoid "b" MR-045
15. Nameplate
16. Fixing screws: 4 pcs M10x60 to
ISO 4762 -10.9
tightening torque Md = 64 Nm
17. Fixing screws: 2 pcs M6x55 to
ISO 4762 -10.9
tightening torque Md = 14 Nm
18. O-ring ports P,A,B,T 22,22 x 2,62
19. O-ring ports X,Y, 10x2
20.1 Plug-in connector "a" grey
20.2 Plug-in connector "b" black
21. Connecting dimmensions to ISO 4401
Required quality of
the mating surface.
27/01/14 55
Model code
K V - 4 / 1 6 - - -

Two positions 2
Three positions 3

Pilot oil supply and discharge
Three positions Two positions
Internal x, y
N
Spool types
1
Internal y, external x
2
3
YN
4
5
Internal x, external y
6
R1
XN
R2
R3
External x, y
R4
R5
Z
R6
R51
For supply and discharge with spool type 2 and 3, refer to the features
F51 table.
51A
51B
56 27/01/14
- - - -
*
Supply voltage
12V 12 DC 12 AC
24V No designation 24 AC
48V 48 DC 48 AC
110V 110 DC 110 AC
230V 230 DC 230 AC*
- Alternating voltage solenoids are fitted with a bridge rectifier.

- With solenoids of over 48 V an earthing clamp ( )
to DIN EN 175301-8003 must be connected.
* To fulfil EMC (89/336/EEC) a capacitor must be built in.
Connector type
EN 175301-803, without signal lamp No designation
EN 175301-803, with signal lamp L
Deutsch V
Overvoltage
Pilot oil control with a double throttle valve

Without a double throttle valve No designation
With a double throttle valve H
Pilot oil control with pressure reducing valve

Without pressure reducing valve No designation
With pressure reducing valve RT
Pre-load valve
Without pre-load valve No designation
With pre-load valve V
Throttle mm [in]
Throttle Ø 0,8 [0.03 dia] D08
Seal type
E
24568 and ISO 15380
27/01/14 57
58 27/01/14
• NG 6
• Up to 250 bar [3 625 PSI]
• Up to 40 L/min [10,6 GPM]
• Different types of plug-in connectors.
• 3-chamber model.
KV-4/3-3KO-6
Directional valves type KV-3KO with direct solenoid operation control the direction of the Spool types
hydraulic medium flow.
These directional valves consist of a housing (1), a control spool (3), and one solenoid (2)
with two return springs (4) in 4/2-way directional valves, and two solenoids (2) with two
return springs (4) in 4/3-way directional valves. In 4/3-way directional valves the centre
position of the control spool is the neutral position. The change-over to the operating
position (a) and (b) is done by energizing the solenoids (2) "a" and "b" respectively,
whereby the solenoid plunger acts on the control spool (3) via the operating pin (5), thus
clearing the corresponding flow ways and establishing relevant links between ports A, B, P,
and T.
When the solenoid (2) is de-energized, the control spool (3) is returned to its neutral
position by the return spring (4). The change-over can be done manually by pressing the
emergency manual override (6).
27/01/14 59
Features
Hydraulic
Size 6
Ports A, B, P bar [PSI]
Operating pressure 250 [3 625]
PortT bar [PSI]
15 to 380 [69.5 to 1 760]

Mass 4/2 1,3 [2.9]
kg [lb]
4/3 1,8 [3.9]
Electrical
Direct 12, 24, 48
Supply voltage V
Power W 26
Switch-on time* ms 50 to 80
Switch-off time* ms 30 to 55
Ambient temperature °C [°F] to50 [122]
Coil temperature °C [°F] to180 [356]
* The switching-on and off times apply to 24 V DC solenoids.

2
Measured at 50°C [122°F] and viscosity of 32 mm /s [148 SUS]. Measured at 50°C [122°F] and viscosity of 32 mm2/s [148 SUS].
Diff. pressure
Pressure
Flow
Flow
Flow path
Spool P-A P-B A-T B-T P-T Spool curve
1 1 1 2 2 - 1 1
2 3 3 3 3 5 2 2
3 1 1 4 4 - 3 3
6 1 1 1 1 - 6 4
51A, 51B 1 1 3 3 - 51A, 51B 1
41A, 41B 3 3 - - - 41A, 41B 5
60 27/01/14
Dimensions
Connection diagram and connecting

KV-4/2-3KO-6
Option: Plug-in connector to ISO 4400 Option: AMP JUNIOR connector
Max. torque 50 Ncm
KV-4/3-3KO-6
Name plate
Max. torque 30 Nm
Max. torque 6 Nm
4 x Fixing screws M5x50 to ISO 4762- 10.9 must be ordered separately.

Required tightening torque Md= 7Nm.

mating surface.
Cartridge throttle

27/01/14 61
Model code
K V - / - 3 K O - 6 -
Working ports

Two positions 2
Three positions 3

Spool types
1 1A 1B
2 2A 2B
3 3A 3B
6 6A 6B
51A 51B
41A 41B
Port T in the valves with spool type 41A and 41B to be used as lekage line when
working pressure is higher than 210 bar [3 045 PSI].
62 27/01/14
-
*
Supply voltage
12 V 12 DC 12 AC
48 V 48 DC 48 AC
110 V 110 DC 110 AC
230 V 230 DC 230 AC
- Alternating voltage solenoids are fitted with a bridge rectifier.

- With solenoids of over 48 V an earthing clampto ISO 4400 must
be connected
Connector type
Deutsch V
Throttle mm [in]
Seal type
No designation
DIN 51524
E
27/01/14 63
64 27/01/14
4/2, 4/3 WAY DIRECTIONAL PROPORTIONAL VALVE KVP (NG 6)
• NG 6
• Up to 350 bar [5 076 PSI]
• Plug-in connector for solenoids to ISO 4400.Connection diagram and connection
• 5 chamber models with good spool guidance.Optional control electronics: Amplifier P/N:
1659574.
KVP-4/3-5KO-6
The KVP directional control valve is a proportional valve providing variable flow rates. This Spool type
valve is used with control electronics. Typical applications are soft switching via adjustable
ramps for the reduction of hydraulic and mechanical shocks, and electrically adjustable
flow rates - speeds for automating machine functions.
This directional valves consist of a housing (1), a control spool (2), one or two proportional
solenoids (3) and two return springs (4). The change-over can be done manually by
pressing the emergency manual override (5).
27/01/14 65
Features
Hydraulic
Size 6
Flow rate L/min [GPM] 10, 20, 30 [2.6 - 5.2 - 7.9]
A, B, P 350 [5 076]
T 250 [3 625]
Viscosity range mm2/s [SUS] 15 to 380 [3.24to82]
4/2 1,65 [3.63]
Mass kg [lb]
4/3 2,2 [4.85]
Proportional
Hysteresis 5% of max. flow rate
12 DC 2
Nominal current A
24 DC 1
Electrical
Power W 36
Ambiant temperature °C [°F] to+50 [to +122]
Dimensions
Connection diagram and connecting
dimensions to ISO 4401
Max. torque 6 Nm
Max. torque 50 Nm
Fixing screws 4 pcs M5 x 30 to EN ISO 4762 - 10.9 must be

ordered separately / Max. torque Md = 9Nm

mating surface
66 27/01/14
Input signal curves / Flow rate Power limits transmitted

2
Measured at 40°C [104°F] and viscosity of 32 mm /s. Measured at 40°C [104°F] and viscosity of 32 mm2/s.
P=5 bar [72.5PSI] P-A or P-B
Flow
Flow
% Pp
Model code
K V P - 4 / - 5 K O - 6 -
*
Number of spool positions
Two positions 2
Three positions 3
briefly specified
Spool types
1A
1B
Seal type
6A
NBR seals for mineral oil HL, HLP, to
No designation
DIN 51524
6B FPM seals for HETG, HEES, HEPG
E
to VDMA 24568 and ISO 15380
Connector type
No designation EN 175301-803 without signal lamp
Regulated flow rate
(P=5 bar [72.1 PSI] / P-A or P-B) L EN 175301-803 with signal lamp
0-10 L/min [0-2.6 GPM] 10 K EN 175301-803 without connector
0-20 L/min [0-5.2 GPM] 20 V Deutsch
0-30 L/min [0-7,9 GPM] 30
Supply voltage
27/01/14 67
68 27/01/14
4/2, 4/3 WAY BANKABLE DIRECTIONAL VALVES KVM (NG 6)
• NG 6
• Up to 350 bar [5 076PSI]
• Threaded connection to ISO 9974 (Metric), ISO1179 (BSPP/Gas).

• Series or parallel connections.
• Inlet plate possbility with pressure relief valve, pump unloading valve or flow control valve.
• Possibility to use standard components for vertical stacking.
KVM-6-...-VV-KV-N4
Basic concept
1. Basic (directional control) valves KVM-6 5. Threaded connection P
2. Inlet plate OB-KVM-6 6. Threaded connection T
3. End plate ZB-KVM-6 7. Threaded connection A
4. Fixing elements for mounting SET-KVM-6 8. Threaded connection B
9. Threaded connection MP (closed)
Type of connection
Parallel (KVM-P) Series (KVM-S)
27/01/14 69
70 27/01/14
4/2, 4/3 WAY BANKABLE DIRECTIONAL VALVES KVM (NG 6)
• NG 6
• Up to 350 bar [5 076 PSI]
• Parallel or series connection.
• Plug-in connection for solenoids to ISO 4400.
• 5-chamber model with good spool guidance.
KVM-P-4/3-6-1-1-12DC-3/8
Hydraulic symbol
Spool types - Parallel connection (KVM-P)
Spool types - Series connection (KVM-S)
Features
Hydraulic
KVM-P KVM-S
Size 6 6
A, B, P 350 [4 568] 250 [3 626]

T 250 [3 626]
1,85 [4.08]
Mass 4/2 kg [lb]
4/3 2,4 [5.29]
Electrical
29
Power W
(12 V DC supply voltage) 36
Ambiant temperature °C [°F] to +50 [to +122]
27/01/14 71
Dimensions
(Manual override - G)
(Manual override - G)
1. Solenoid ’’a’’ / MR-045-O

2. Solenoid ’’b’’ / MR-045-O
3. Plug-in connector «a» -grey
4. Plug-in connector «b» -black
6. Manual override with rubber (G)
7. O-ring 9,25 x 1,78
8. Valve cap (KVM-...-4/2)
9. Nameplate
10. Threaded connection A-M torque = max. 100 Nm
11. Threaded connection B-M torque = max. 100 Nm
Connection dimensions for KVM-6
Required quality of the mating surface
72 27/01/14

Parallel connection -KVM-P (N1 to N8) .Series connection -KVM-S (P to T).
Diff. pressure
Diff. pressure
Flow Flow
Series connection -KVM-S (P to A(B)).
Diff. ressure
Flow
The operating limits of the valve shall be determined at a voltage 10% bellow
the nominal rating. The curves refer to application with symmetrical flow
throw the valve (P-A and B-T). In the case of asymmetrical flow (e.g. one part
not used) reduced values may result.
Pressure
Spool type Curve

1 1
2 2
3,6 3
Flow
27/01/14 73
Model code
K V M - - 4 / - 6 -
Type of connection
Series connection S
Parallel connection P

Two positions 2
Three positions 3

Manual override with rubber G
Spool type
1A
3A
6A
Parallel connection
(KVM-P)
51A
1B
3B
6B
51B
81
Series connection
2A
(KVM-S)
2B
74 27/01/14
- - -
*
Supply voltage
Connector type
Deutsch V
M18 x1,5 No designation
G3/8 3/8
9/16-18 UNF-2B SAE 6
Seal type
FPM seals for HETG, HEES, HEPG to VDMA 24568 and ISO 15380 E Electrically operated
27/01/14 75
76 27/01/14
VERTICAL STACKING FOR KVM VALVES
• NG 6
• Up to 350 bar [5076 PSI]
• Up to 40 l/min [10.56 GPM]
• Threaded connections to ISO 9974, ISO 1179 or ISO 11926.

• Possibility of stacking one, two or three vertical stacking components.
Mounting example Hydraulic symbol
B
1. Bankable directional valve KVM-6
2. First stacking component (KVM-NOV-6) A
3. Second stacking component (KVM-NDV-6)
4. Third stacking component (KVM-VV-6)
5. Mounting screws for vertical stacking components:
• M5x55, ISO 4762-10.9 (for one stacking component) - ordering code: 1114573
• M5x95, ISO 4762-10.9 (for two stacking components) - ordering code: 1253603
• M5x135, ISO 4762-10.9 (for three stacking components) - ordering code: 1668356
Mounting screws tightening torque: max. 9 Nm [79.6 in.lbf]
45 [1.77]
4
45 [1.77]
2
45 [1.77]
1
a
a
55 [2.16]
P
23
0
5
[0.90]
B
T
b
47 [1.85]
[0.92]
23,5
Threaded connections options:

• M16x1,5 (ISO 9974-1)
• G3/8 (ISO 1179-1)
• 9/16-18 UNF-2B (ISO 11926-1)
27/01/14 77
Directional valve KVM and KVM-VV-6 relief valve mounting example Hydraulic symbol
A B
4
45 [1.77]
a
55 [2.16]
a
A
P
23
5
0
[0.90]
B
T
47 [1.85]
b
[0.92]
23,5
b
Directional valve KVM and KVM-NDV-6 throttle valve mounting example Hydraulic symbol
A B
3
45 [1.77]
1
a
P
55 [2.16]
0
23 5
B
T
[0.90]
b
47 [1.85]
[0.92]
23,5
78 27/01/14
Solenoid orientation options Sealing between stacking elements
Six different orientation options:
30° 30°
[dia. 0.07]
1,78
17,2
[dia. 0.68]
30° 30°
27/01/14 79
80 27/01/14
CHECK VALVE KVM-NOV-6
• Up to 350 bar [5 076 PSI]
• Up to 40 l/min [10,6 GPM]
• Flow shut-off in both or one service line.

• For vertical stacking on KVM directional valves.

A B
Pilot operated check valves type KVM-NOV-6 enables the hydraulic fluid flow in the service
lines to be automatically shut off and made free, respectively.
Free flow direction is always from the valve side to the ports side. In the opposite direction KVM-NOV-6-D
is the valve blocked for the hydraulic fluid flow. Free flow in port A in direction from ports to
valve side is achieved by means of pressure in port B and vice versa.
To assure zero leakage there is necessary to discharge ports A and B towards port T in the
zero position of the directional valve. A B
KVM-NOV-6-EA
A B
KVM-NOV-6-EB
Features Mounting example
Size 6
Cracking pressure bar [PSI] 1 [14.5] A B
Area ratio 1:3,9
Filtration ISO 4406: 1999 19/17/14
Mass kg [lbs] 1,4 [3.0]
a
a
P
A
0
B
T
b
b
27/01/2014 81
Dimensions
45 [1.77]
116 [4.57] 45 [1.77]
40,5 [1.59]
0,75 [0.03]
37,5 [1.48] Threaded

5,5 [0.22] connections
[0.61]
15,5
0.01
Rmax 8
31 [1.22]
[1.28]
32,5
Measured at 50C [122F]
and viscosity of 32 mm2/s [148 SUS].
bar [PSI]
10 145
8 116
Diff. pressure
6 87
4 58 Against spring force

Pilot opened
2 29
0 0
0 5 10 15 20 25 30 35 40 l/min
[0] [1.32] [2.64] [3.96] [5.28] [6.60] [7.93] [9.25] [10.57] [GPM]
Flow
Model code
K V M - N O V - 6 - - - -
*
Symbol
A B Threaded connections Special requirements
to be briefly specified
M16 x 1,5 (ISO 9974-1) No designation
D G3/8 (ISO 1179-1) 3/8
9/16-18 UNF-2B (ISO 11926-1) SAE6
A B
EA
Seal type
A B
E
24568 and ISO 15380
D
82 27/01/2014
THROTTLE WITH CHECK VALVE KVM-NDV-6
• Up to 350 bar [5 076 PSI]
• Up to 40 l/min [10.6 GPM]
• Flow control in both or one service line.

• For flow throttling in supply and/or return lines.
Throttle with check valves type KVM-NDV-6 are used for throttling flow of the A B A B
hydraulic fluid in lines A and/or B. The KVM-NDV-6 valves are allowing free flow
in one direction through check valve and throttled flow in reversed direction. D0 D1
Hydraulic fluid flow is throttled depending od adjustment of the throttling screw.
A B A B
A0 A1
A B A B
B0 B1
Features Mounting example
Size 6
Cracking pressure bar [PSI] 0,5 [7.2]
A B
Filtration ISO 4406: 1999 19/17/14
Mass kg [lbs] 1,5 [3.3]
a
a
P
A
0
B
T
b
b
27/01/2014 83
Dimensions
SW13
45 [1.77]
100 [3.94] 45 [1.77]
141 [5.55] throttles closed
160 [6.30] throttles opened
SW5
40,5 [1.59] Throttling screw*
0,75 [0.03]
37,5 [1.48] Threaded

5,5 [0.22] connections
[0.61]
15,5
0.01
31 [1.22]
Rmax 8
[1.28]
32,5
* Clockwise rotation reduces the hydraulic fluid flow.It is recommended that the valve is set at zero pressure in setting line.
P-Q Performance curve

bar [PSI]
20 290
18 261
16 232
14 203
Diff. pressure
12 174
10 145 Through check
valve
8 116
6 87
4 58
2 29
0 0
0 5 10 15 20 25 30 35 40 l/min
[0] [1.32] [2.64] [3.96] [5.28] [6.60] [7.93] [9.25] [10.57] [GPM]
Flow
84 27/01/2014
Model code
K V M - N D V - 6 - - - -
*
Symbol
A B Threaded connections Special requirements
D0 G3/8 (ISO 1179-1) 3/8
9/16-18 UNF-2B (ISO 11926-1) SAE6
A B
A0
Seal type
A B FPM seals for HETG, HEES, HEPG to VDMA
E
24568 and ISO 15380
B0
A B
D1
A B
A1
A B
B1
27/01/2014 85
86 27/01/2014
PRESSURE RELIEF VALVE KVM-VV-6
• Up to 350 bar [5 076 PSI]

• Direct operated.
• Multiple pressure setting ranges.
• Various hydraulic symbols.
Operation
Throttle with check valves type KVM-NDV-6 are used for throttling flow of the hydraulic fluid in lines A and/or B. The KVM-NDV-6 valves
are allowing free flow in one direction through check valve and throttled flow in reversed direction. Hydraulic fluid flow is throttled
depending od adjustment of the throttling screw.
Hydraulic symbols
KVM-VV-6-AB KVM-VV-6-BA KVM-VV-6-AT
A B A B A B
T
KVM-VV-6-DT KVM-VV-6-DD
A B A B
KVM-VV-6-BT
A B
T T
Features
Size 6

Pressure setting range bar [PSI] 15 - 350 [270 - 5 076]
Filtration ISO 4406: 1999 19/17/14
Mass kg [lbs] 1,1 - 1,8 [2.4 - 4.0]
27/01/2014 87
Dimensions
SW19
45 [1.77]
L3 L2 45 [1.77]
L1
SW5
Adjusting screw*
40,5 [1.59]
37,5 [1.48]
0,75 [0.03]
5,5 [0.22] Threaded

L5 connections
[0.61]
15,5
Mating surface quality

0.01
31 [1.22]
[1.28]
32,5
Rmax 8
* Clockwise rotation increases pressure rise at the inlet port of pressure relief valve.
L1 L2 L3 L4 L5 Mass
Option
mm [inch] mm [inch] mm [inch] mm [inch] mm [inch] kg [lbs]
KVM-VV-6-AB 109 [4.29] 70 [2.76] 0 39 [1.53] 13,5 [0.53] 1,1 [2.42]
KVM-VV-6-BA 109 [4.29] 70 [2.76] 39 [1.53] 0 13,5 [0.53] 1,1 [2.42]
KVM-VV-6-AT 144 [5.67] 100 [3.94] 44 [1.73] 0 29 [1.14] 1,6 [3.53]
KVM-VV-6-BT 121,5 [4.78] 80 [3.15] 0 41,5 [1.63] 8,5 [0.33] 1,3 [2.87]
KVM-VV-6-DT 188 [7.40] 100 [3.94] 44 [1.73] 44 [1.73] 28,5 [1.12] 1,8 [3.97]
KVM-VV-6-DD 188 [7.40] 100 [3.94] 44 [1.73] 44 [1.73] 28,5 [1.12] 1,8 [3.97]

bar [PSI]
400 5802
350
360 5221
320 4641
280 4061
240 3481
Diff. pressure
200
200 2901
160 2321
120
120 1740
80 1160
50
40 580
0 0
0 5 10 15 20 25 30 35 40 l/min
[0] [1.32] [2.64] [3.96] [5.28] [6.60] [7.93] [9.25] [10.57] [GPM]
Flow
88 27/01/2014
Model code
K V M - V V - 6 - - - -
*
Symbol
A B
Special requirements
D0
A B
G3/8 (ISO 1179-1) 3/8
9/16-18 UNF-2B (ISO 11926-1) SAE6
A0
A B
B0
Pressure setting range
T bar [PSI]
A B
15 - 50 [217 - 725] 50
51 - 120 [740 - 1740] 120
D1 121 - 200 [1755 - 2900] 200
201 - 350 [2915 - 5076] 350
T
A B
A1
A B
B1
27/01/2014 89
90 27/01/2014
VERTICAL STACKING ON VALVES KVM
WITH STANDARD SANDWICH VALVES TO ISO 4401 (NG 6)
VERTICAL STACKING ON VALVES KVM WITH STANDARD

SANDWICH VALVES TO ISO 4401 (NG 6)
• NG 6
• Up to 350 bar [5076 PSI]
• Up to 40l/min [10.57 GPM]
• Use standard components for vertical stacking.

• Threaded connections to ISO 9974 or ISO 1179.
• Possibility of stacking one or two standard components.
KVM-P-4/3-5KO-6 and VP-NOV-6 for stacking
Description Hydraulic symbol

One standard component
1. Bankable directional valve KVM-6
2. STACK-KVM-6 consist of: VP-NOV-6 VP-NDV-6
2.1 Adapter plate and two O-rings 18,77 x 1,78
2.2 End plate and two O-rings 9,25 x 1,78
2.3Fixing screws M5x100 ISO 4762-10.9 (for one stacking component)
or M5x140 ISO 4762-10.9 (for two stacking components)
3. First stacking component (standard VP-NOV-6 or VP-NDV-6)
4. Second stacking component (standard VP-NDV-6)
(Two components)
Two standard components
Mtorque = max. 9Nm [79.6 in.lbf]
27/01/14 91
Model code
S T A C K - K V M - 6 - - - -
*
Number of stacking components
One standard component N1
Two standard components N2
G3/8 (ISO 1179) 3/8
M18 x 1,5 (ISO 9974) No designation
Seal type
FPM seals for HETG, HEES, HEPG to VDMA 24568
E
and ISO 15380
92 27/01/14
AUXILIARY CONTROL LEVER
• Compatible with KV-5KO-6, KVM-6 and KVP-5KO-6 directional valves
• Without impact on valve´s performance.
• Up to 250 bar [3 625 PSI] on T port.
Description Hydraulic symbols
The optional auxiliary control lever module offers solenoid or manual operation of a\0/b
A B
directional valves. Control lever provides mechanical connection with main control
spool without significant impact on valve's performance. Auxiliary control lever a 0 b
module is mounted between the valve housing and solenoid. During solenoid
operation, hand lever remains in neutral position. Modular and robust design of a P T b
auxiliary control lever enables installation on A or B side of various types of
directional valves and operating pressure range up to 250 bar [3 625 PSI] on T port. a\0/b
A B
a 0 b
a P T b
Features
Size 6
Operating pressure
Port T bar [PSI] 250 [3 626]
Filtration ISO 4406: 1999 19/17/14
Lever actuating force (end stroke) N [lbf] 40 [9.0]
Mass (ACL module) kg [lbs] 0,9 [1.98]
Dimensions
12° 12°
83 [3.27]
139 [5.47]
73 [2.87] 78 [3.07] 56 [2.20] 46 [1.81]

280 [11.02] 52 [2.05]
27/01/2014 93
Model code
The auxiliary control lever on valves KV-5KO-6 and KVM-6 is defined by the designation in the manual override option field.
K V - 4 / 3 - 5 K O - 6 - - ...
K V M - P or S - 4 / 3 - 6 - - ...

Manual override with rubber G
Auxiliary control lever on valve side A FA
Auxiliary control lever on valve side B FB
The auxiliary control lever on valves KVP-6 is defined by the designation FA or FB in the special requirements field.
94 27/01/2014
INLET PLATE OB-KVM-6 (NG 6)
• NG 6
• Up to 350 Bar [5076 PSI]
• Up to 40 L/min [10,6 GPM]
• Provide pressure relief valve.
• Provide pump unloading valve.
• Provide flow control valve.
• Threaded connections to ISO 9974 (Metric),
ISO 1179 (BSPP/Gas), ISO 11926 (UNF).
OB-KVM-6-VV20-KVO OB-KVM-6-VV20-TVTPG
Hydraulic symbol
OB-KVM-6 OB-KVM-6-VV20-KV1
OB-KVM-6-VV35 OB-KVM-6-VV20-TVTP
By-pass way
Features
OB-KVM-6 OB-KVM-6-VV OB-KVM-VV-KV OB-KVM-VV-TVTP


Mass kg [lbs] 1,25 [2.76] 1,35 [2.98] 2,2 [4.85] 4,5 [9.92]
Flow rate l/min [GPM] / 40 [10.6]
/ 50-210 [13-55]
Press Setting bar [PSI]
/ 100-350 [26-92]
Adjustments / allen key
Max. pressure bar [PSI] / / 350 [5 076] 210 [3 045]
Supply voltage V DC / / 12, 24 /
Power W / / 17 /
Flow - inlet l/min [GPM] / / / max. 50 [max. 13,21]
Flow - priority way l/min [GPM] / / / 0 - 25 [0 - 6.6]
Flow - bypass l/min [GPM] / / / max. 40 [max. 10,6]
27/01/14 95
Dimensions
OB-KVM-6 OB-KVM-6-VV...-KV...
OB-KVM-6-VV
1. Pressure relief valve

2. Pump unloading valve
3. Manual override with knob
4. Threaded connection MP - G1/4 (closed)
6. Connection dimensions for KVM-6
7. Fixing hole (M8 X 12) for mounting assembly
96 27/01/14
Dimensions
OB-KVM-6-VV...-TVTP...
KVM-6-Ventile - Bypass-Strom
KVM-6-Ventile - Hauptstrom
1. Pressure relief valve
2. Flow control valve - rotary knob -TVTPB
3. Flow control valve - proportional solenoid - TVTP
4. Flow control valve - proportional solenoid with manual
override - TVTPG
5. Threaded connection MP - G1/4 (closed)
6. Nameplate
7. Bankable directional valves KVM-6 Priority flow
8. Bankable directional valves KVM-6 Bypass flow
9. Fixing hole (M8 x 12) for mounting assembly
10. Connection dimensions for KVM-6 (see page 12.11.3)
27/01/14 97

.OB-KVM-6-VV (pressure relief valve- flow P to T. OB-KVM-6-KV (pump unloading valve- flow P to T.
Pressure drop
Pressure drop
Flow Flow
98 27/01/14
Model code
O B - K V M - 6 - - - - - - -
*
Pressure relief valve
Without pressure relief valve No designation
Pressure relief valve range 50-210 bar
VV20
[725-3045 PSI]
Pressure relief valve range 100-350 bar
VV35
[1450-5076 PSI]
Pump unloading valve

No
Without pump unloading valve designation
Pump unloading valve - normally closed KV0
Pump unloading valve - with manual override - knob KVG0
Pump unloading valve - normally open KV1
Pump unloading valve - with manual override - knob KVG1
Normally open Normally closed
Flow control valve
Without flow control valve No designation
Flow control valve - rotary knob - TVTP-25-B TVTPB
Flow control valve - prop. solenoid - TVTP-25-P TVTP
Flow control valve - with manual override - knob TVTPG
supply voltage
Direct voltage 24 V No designation
Direct voltage 12 V 12
M22 x 1,5 (ISO 9974) M22
G1/2 (ISO 1179) 1/2
G3/8 (ISO 1179) 3/8
3/4-16 UNF-2B SAE 8
Plug-in connector
Without signal lamp No designation
With signal lamp L
Seal type
E
and ISO 15380
27/01/14 99
100 27/01/14
END PLATE ZB-KVM-6

Dimensions
Fixing hole M8 x 12 for mounting
assembly
Threaded connection
(reserve port T)
ZB-KVM-6
* ZB-KVM-6-PT-1/2(M22) = 27 Mass = 0,8 kg
Model code
Z B - K V M - 6 - - - -
*
Symbol
No designation
PT
((It is necessary to use this end plate by series

connections KVM-S)(
M22 x 1,5 (ISO 9974) M22

G1/2 (ISO 1179) 1/2
G3/8 (ISO 1179) 3/8
3/4-16 UNF-2B 3/4-16UNF
Seal type
NBR seals for mineral oil HL, HLP to DIN
No designation
51524
E
27/01/14 101
102 27/01/14
FIXING ELEMENTS FOR MOUNTING
• SET-KVM-6 consists of:
a) Nuts: 3 x M8 DIN 1587
b) Washers: 3 x A8 DIN 6798-J
c) Screws: 3 x M8 DIN 939 10.9
SET-KVM-6-N3
Description Model code
Screw M8 DIN 939 10.9:

S E T - K V M - 6 -
Number of bankable directional

valves KVM-6
L mm [in] :Max. number of bankable One valves KVM-6 N1
80 [3,15]
N1 valves KVM: Two valves KVM-6 N2
N2 127 [4,99] Three valves KVM-6 N3
N3 174 [6,85] a) parallel connection (KVM-P) = Four valves KVM-6 N4
eight valves (max. N8).
N4 221[8,70] Five valves KVM-6 N5
N5 268 [10,55] Six valves KVM-6 N6
N6 315 [12,40] Seven valves KVM-6 N7
N7 362 [14,25] Eight valves KVM-6 N8
N8 409 [16,10]
27/01/14 103
Dimensions
OB-KVM-6, OB-KVM-6-VV
H1 H2
OB-KVM-6 or OB-KVM-6-VV... 75+Nx47 (N = 1 to 8) 39+Nx47 (N = 1 to 8)
OB-KVM-6-VV...-KV... 90+Nx47 (N = 1 to 8) 54+Nx47 (N = 1 to 8)
OB-KVM-6-VV...-TVTPB...
1. [141 in.lbf]Mtorque / Parallel connection (KVM-P) - max. 20Nm [177 in.lbf] / Series connection (KVM-S) - max. 16 Nm
104 27/01/14
6/2 WAY DIRECTIONAL VALVE KV (NG 6)
• NG 6
• Up to 350 bar [5 076 PSI]

KV-6/2-6-S50
Directional valves type KV with direct solenoid operation control the direction of the Spool type
hydraulic medium flow. They are mostly used as link between two consumers and the
basic directional valve, when we want to control both consumers alternately by means of
one basic directional valve.
The KV type directional valves consist of a housing (1), a control spool (2), a solenoid (3)
and a return spring (5).
Change-over to the operating position is done by energizing the solenoid (3), whereby the
solenoid plunger acts on the control spool (2) via the operating pin (4), thus clearing the
corresponding flow ways and establishing respective links between the ports
P1, A, B and P2.
Mounting example
position by the return spring (5), thus establishing again the links between ports P1, C, D
and P2.
The change-over can also be done manually by pressing the emergency manual override
(6).
27/01/14 105
Features
Hydraulic
Size 6
With YZ 350 [5 076]
Without YZ 250 [3 625]

Mass kg [lb] 2,5 [5.51]
Electrical
Power W 29 *
Dimensions
Max. torque 6 Nm
Threaded connections YZ
3. Solenoid ’’a’’ MR-045

7. Plug in connector «a» grey
8. Nameplate
9. Valve cap
With hand operation
106 27/01/14
p-Q Performance curve

Diff. pressure
Flow
Model code
K V - 6 / 2 - 6 - - - - - - - - S 5 0 -
*
Spool type
No designation
AB Special requirements to
be briefly specified
Overlap
Seal type
No designation
No designation
HLP to DIN 51524
P E HEPG to VDMA 24568 and
ISO 15380

Drainage
YZ With YZ
Supply voltage

Threaded connections M ; YZ
Connector type No designation M18x1,5 ; M14x1,5
EN 175301-803 without signal lamp No designation M22 M22x1,5 ; M14x1,5)
EN 175301-803 with signal lamp L 3/8 G3/8 ; G1/4)
EN 175301-803 without connector K 1/2 G1/2 ; G1/4)
AMP Junior timer without connector M SAE 8 3/4-16 UNF-2B; 9/16-18 UNF-2B
Deutsch V
Without protection No designation
With protection T
27/01/14 107
108 27/01/14
• NG 10
• Up to 350 bar [5 076 PSI]
• Up to 120 L/min [31.7 GPM]

KV-6/2-10
Directional valves type KV with direct solenoid operation control the direction of the
The KV type directional valves consist of a housing (1), a control spool (2), a solenoid (3)
and a return spring (5).
P1, A,B and P2.
position by the return spring (5), thus establishing again the links between ports P1, C,D Mounting example
and P2.
(6).
A
P1 P2
6 3 4 1 2 5
A B
A B
P1 P2
C D L
C D L
27/01/14 109
Features
Hydraulic
Size 10
With YZ 350 [5 076]
Without YZ 250 [3 625]
Oil temperature range °C [°F] -20 to+70 [-4 to +158]
Mass kg [lb] 5,5 [12.12]
Electrica
Power W 45
Ambient temperature °C [°F] to+50 [to +122]
Coil temperature °C [°F] to+180 [to +356]
Dimensions
[0.6]
[4.8] )(with manual override)
[4.5]
Threaded connection YZ
[1.10] [1.81] YZ
[4]
[2.69]
[1.25]
108 [4.25] [5.11]
246 [9.68]
[2.2] [1.81] Threaded connections M

[1.33] [1.81]

[2.87]
7. Plug-in connector «a» - grey

[1.97]
8. Nameplate
9. Valve cap
[1.43]
[0.45]
Max. torque = 6Nm

[1.24] [2.63]
110 27/01/14
Diff. pressure
Flow
Model code
K V - 6 / 2 - 10 - - - - - -
*
Supply voltage
Connector type
Deutsch V
Overvoltage
M22x1,5; M14x1,5 M22
M27x2; M14x1,5 M27
G1/2; G1/4 1/2
G3/4; G1/4 3/4
7/8-14 UNF-2B; 9/16-18 UNF-2B SAE 10

Drainage
With YZ YZ
Seal type
E
24568 and ISO 15380
27/01/14 111
112 27/01/14
• NG 16
• Up to 350 bar [5 076 PSI]
• Up to 250 L/min [66.04 GPM]
• Threaded connections to ISO 1179 (BSPP/Gas), ISO 11926 (UNF).
• Flange ports to ISO 6162-2.
• Fulfil EMC (89 / 336 / EEC).
KV-6/2-16-XN
Hydraulic symbol
KV-6/2-16-...-XN KV-6/2-16-...-N KV-6/2-16-...-Z
Features
Hydraulic
Size 16
Flow rate L/min [GPM] 250 [66]
bar [PSI] 15 to 350 [217.56 to 5076.32]
Operating pressure
(in port L or in return way) bar [PSI] 250 [3625.94]
Mass kg [lb] 22 [48.50]
Electrical
W 29
Power
27/01/14 113
Dimensions
KV-6/2-16-...-G1/G1/4 Threaded connections M

A, B, C, D, P1, P2

4. Nameplate
Threaded connections L
G1/4
KV-6/2-16-...-SAE...
Size
SAE 3/4 SAE 1
a 50.8 [2] 57.2[2.25]
23.8 [0.94]
b 27.8 [1.09]
M1 M10 M12
SAE-flange connection - High pressure serie
Threaded connections L

4. Nameplate
114 27/01/14
Pressure drop
Flow
Model code
K V - 6 / 2 - 16 - - - - - -
*
Pilot oil supply and discharge
Internal x, y N
Internal, external y (port L) XN
external, external Z
Threaded connections M ; L
G1 ; G1/4 G1/G1/4
1 5/16-12 UNF-2B ; 9/16-18 UNF-2B SAE 16
SAE-Flange connections 3/4 - high pressure series SAE3/4
SAE-Flange connections 1 - high pressure series SAE1

supply voltage
direct voltage 24 V No designation
direct voltage 12 V 12 DC
Connector type
G1/2 (YZ=G1/4) without connector K
Deutsch V
without overvoltage protection No designation
with overvoltage protection T
Seal type
E
24568 and ISO 15380
27/01/14 115
116 27/01/14
6/2 WAY DIRECTIONAL VALVES KV-6K (NG 6)
• NG 6
• Up to 250 bar [3 625 PSI]
KV-6K/2-6
Directional valves type KV-6K/2-6 with direct solenoid operation control the direction of the Spool type
valve.
The KV-6K/2-6 type directional valves consist of a housing (1), a control spool (2), and a
solenoid (3) with return spring (5).
P1, A,B and P2.
Mounting example
position by the return spring (5), thus establishing again the links between ports
P1, C,D and P2.
(6).
27/01/14 117
Features
Hydraulic
Size 6
Viscosity range mm2/s [SUS] 15 to 380 [3,24 to 82]
Mass kg [lb] 2,5 [5.51]
Electrical
Power W 29
(12 V DC supply voltage) W 36
Dimensions
Threaded connection
3. Solenoid ’’b’’ MR-045

7. Plug in connector «b» black
8. Nameplate
9. Valve cap
118 27/01/14

Pressure drop
Flow
Model code
K V - 6 K / 2 - 6 - - - - -
*
Supply voltage briefly specified
VDirect voltage 12V 12 DC
Connector type
Deutsch V
Overvoltage
G 3/8 G3/8
9/16-18 UNF-2B SAE 6
Seal type
FPM seals for HETG, HEES, HEPG to VDMA 24568 and
E
ISO 15380
27/01/14 119
120 27/01/14
6/2 WAY DIRECTIONAL VALVES KVH (NG 6)
• NG 6
• Up to 315 bar [4 568 PSI]
• For stacking (1-5 units).
KVH-6/2-6-S50-N3
Directional valves type KVH with direct solenoid operation control the direction of the
valve.
The KVH type directional valves consist of a housing (1), a control spool (2), and a
Change-over to the operating position is done by energizing the solenoid (3), whereby the Mounting example
P1, A, B and P2.
P1, C, D and P2.
(6).
27/01/14 121
Features
Hydraulic
Size 6
With YZ 315 [4 568]
Without YZ 250 [551]
Oil temperature range °C [°F] -20 to +70 to +158]
Mass kg [lb] 2,7 [5.95] (N1)
Electrical
29
Power W
Ambient temperature °C [°F] to +50 [to+122]
Dimensions
Threaded connections YZ
LA= 39,5 (G3/8, M18x1,5)

37,5 [1.47] (G1/2, M22x1,5)

7. Plug-in connector <<a>>-grey
8. Nameplate
9. O-Ring ; M18x1,5 / G3/8 = Ø21x2
Screws
M22x1,5 / G1/2 = Ø26x2

10. O-Ring ; M14x1,5 / G1/4 = Ø17x2
11. Valve cap
122 27/01/14
.Measured at 50°C [122°F] and viscosity of 32 mm2/s [148 SUS].]
Diff. pressuree
Flow
Model code
K V H - 6 / 2 - 6 - - - - - - - S 5 0 - - -
*
symbol
No designation
AB
Special
requirements to be
briefly specified
Overlap Number of units

N1 One
No designation
N2 Two
N3 Three
P N4 Four
N5 Five

Emergency manual override No designation Seal type
Manual override with rubber cover G No NBR seals for mineral oil HL,
designation HLP to DIN 51524
Supply voltage ISO 15380
Direct voltage 12V 12 DC Drainage
YZ With YZ
Connector type
EN 175301-803 without signal lampp No designation
No designation M18x1,5; M14x1,5
M22 M22x1,5; M14x1,5
3/8 G3/8; G1/4
Deutsch V
1/2 G1/2; G1/4
SAE 8 3/4-16 UNF-2b; 9/16-18 UNF-2B
Overvoltage protectionWithout
overvoltage protection
27/01/14 123
124 27/01/14
6/2 WAY DIRECTIONAL VALVES KVH (NG 10)
• NG 10
• Up to 315 bar [4 568 PSI]
• Up to 120 L/min [31.70 GPM]

KVH-6/2-10-N2
Directional valves type KVH with direct solenoid operation control the direction of the
The KVH type directional valves consist of a housing (1), a control spool (2), and a
P1, A, B and P2.
Mounting example
P1, C, D and P2.
(6).
A
A B
6 3 4 1 2 5
C D
C D YZ
A B
P1 P2 YZ
P1 P2 YZ
27/01/14 125
Features
Hydraulic
Size 10
With YZ 315 [4 568]
Without YZ 250 [551]
15 to 380 [3.24 to 82]

Mass kg [lb] 5,5 [12.12]
Electrical
Power W 45
Dimensions
[0.59]
122 (with hand operation)

15
Mmax=50Ncm Threaded connections M

116 [4.57]
Pg 9 (P1)34 (P2) 46 Threaded connections YZ
[1.34] [1.81]
[cca. 4.06]
cca. 103
68.5 [2.7]
32 [1.26]
M8x12 /15 (z=2)

108[4.25] 130 [5.12]
246 [9.68]
[0.75 max.]
(A) 54[2.13] (B) 46 [1.81]

max.19
3 2 1 4 (C) 34 (D) 46
[1.34] [1.81] 7 Mmax. = 20Nm
5
C D YZ
8
A B
n x 73 [n x 2.87]
6 1. Solenoid ’’a’’ MR-060

P1 P2 YZ 2. Plug-in connector «a» - grey
C D YZ 3. Emergency manual override
4. Nameplate
73 [2.87]
[1.97 ±0.01 ]
5. O-Ring ; 26x2 = KVH-6/2-10-G1/2 (M22)

50±0.2
31x2 = KVH-6/2-10-G3/4 (M27)

A B
6. O-Ring 17x2
[1.44]
36.5
7. Screws M10 - 10.9 (z=4)

P1 P2 YZ 8. Valve cap
[0.45]
11.5
[0.75 max.]
18.5 67 ±0.2
max.19
[0.73] [2.64 ±0.01]
126 27/01/14
Pressure drop
Flow
Model code
K V H - 6 / 2 - 10 - - - - - S 4 0 - - -
*
Supply voltage
Special
Connector type requirements to be
EN 175301-803 without signal lamp No designation briefly specified
175301-803 without connector K
Deutsch V
Overvoltage protection Number of units

Without overvoltage protection No designation N1 One
With overvoltage protection T N2 Two
N3 Three
Threaded connections M; YZ N4 Four
M22x1,5; M14x1,5 M22 N5 Five
M27x2; M14x1,5 M27
G1/2; G1/4 G1/2
G3/4; G1/4 G3/4

7/8-14 UNF-2B; 9/16-18 UNF-2B SAE 10
Drainage
With YZ YZ
Seal type
E
and ISO 15380
27/01/14 127
128 27/01/14
• NG 4
• Up to 210 bar [3045 PSI]

• Threaded connections to ISO 9974 (Metric), ISO 1179 (BSPP/Gas).
KV-6K/3-4
Hydraulic
Size 4
2 15 to 380 [69.5 to 1 760]
Viscosity range mm /s [SUS]
Oil temperature range °C [°F] -20 to+70[-4 to 158]

Filtration ISO 4406-1999 19/17/14
Mass kg [lb] 1,6 [3.5]
Electrical
Supply voltage V 12, 24
Power W 25

Diff. pressure
Flow
27/01/14 129
Dimensions
Emergency manual override
Model code
K V - 6 K / 3 - 4 - - -
*
Working ports
Six working ports 6
briefly specified
Three positions 3
Supply voltage
Threaded connections A, B, P
No designation M14x1,5; -
1/4 G1/4; -
Connector type SAE 6 9/16-18 UNF-2B; 9/16-18 UNF-2B
Deutsch V
Overvoltage
130 27/01/14
• NG 6
• Up to 250 bar [3 625 PSI]

KV-8/3-6
Directional valves type KV with direct solenoid operation control the direction of the
hydraulic medium flow. They are mostly used as link between three consumers and the
basic directional valve, when we wish to control both consumers alternately by means of
The KV type directional valves consist of a housing (1), a control spool (2,3), two solenoids
(4,5) with return spring (6,7). Change-over to one of the operating positions is done by
combination of operation of solenoids (4,5), whereby the solenoid plunger acts on the
control spool (2,3) via the operating pin (8), thus clearing the corresponding flow ways and
establishing respective links between the ports P1, A, B, C, D, E, F and P2, as seen forth in
the schematic diagram of a mounting example.
When the solenoid (4,5) is de-energized, the control spool (2.3) is returned to their neutral
position by the return spring (6,7).
The change-over can also be done manually by pressing the emergency manual override Mounting example
(9).
27/01/14 131
Features
Hydraulic
Size 6
Mass kg [lb] 3,8 [8.38]
Electrical
29
Power W
Dimensions
Threaded connection
4.5. Solenoid ’’b’’ MR-045

10. Plug-in connector «b» - black
11. Nameplate
12. Valve cap
132 27/01/14
Pressure drop
Flow
Model code
K V - 8 / 3 - 6 - - - - -
*
Supply voltage
Connector type
Deutsch V
Overvoltage
M22x1,5 M22
M20x1,5 M20
G3/8 G3/8
G1/2 G1/2
3/4-16 UNF-2B SAE 8
Seal type
NBR seals for mineral oil HL, HLP, to DIN 51524 No designation
E
24568 and ISO 15380
27/01/14 133
134 27/01/14
27/01/14 135
Poclain Hydraulics reserves the right to make any modifications it deems necessary to the products described in this document
without prior notification.The information contained in this document must be confirmed by Poclain Hydraulics before any order is
submitted.
Illustrations are not binding.
The Poclain Hydraulics brand is the property of Poclain Hydraulics S.A.
27/01/14
A35758S
A35771G
www.poclain-hydraulics.com

Valve

Uploaded by

Copyright:

Available Formats

Valve

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Valve

Uploaded by

Copyright:

Available Formats

D IR E C T IO N A L

DIRECTIONAL CONTROL VALVES

HYDRAULICALLY OPERATED (AUTOMATIC) 17

Vertical stacking on valves KVM

2/2 way directional valves KVC (NG 6)

Features Hydraulic symbol

P-Q Performance curves

Special requirements to be briefly specified

2/2 WAY DIRECTIONAL VALVES KVC-NV (NG 6)

Features Hydraulic symbol

P-Q Performance curves

Special requirements to be briefly specified

4/2, 4/3 WAY DIRECTIONAL VALVES KV (NG 6, 10)

• Connecting dimensions to ISO 4401.

Operation Hydraulic symbols

3. Control mechanism on side ’’a’’ 3. Control mechanism on side ’’a’’

Required quality of the

Size 6 Size 10 Throttle

Control spool held Seal type

Spool type Throttle mm [in]

6/2 WAY DIRECTIONAL VALVES KV (NG 6, 10)

• Threaded connections to ISO 9974 (Metric), ISO 1179 (BSPP/Gas).

Operation Hydraulic symbols

There are two types of operation:

Threaded LA=39,5 [1.55]( G3/8, M18x1,5)/37,5 [1.47] (G1/2, M22x1,5)

P-Q Performance curves

Control spool held

Threaded connections (M ; YZ)

Special requirements to be briefly specified

POCLAIN HYDRAULICS Hydraulic components - Directional control valves

4/2 WAY AUTOMATIC DIRECTIONAL VALVES PKV (NG 6, 10) )

• Indirect hydraulic operation.

15 to 380 [69.5 to 1 760]

Oil temperature range °C [°F] -20 to +70 [-4 to158]

Connection diagram and

Connection diagram and 1. Emergency manual override

P-Q Performance curves

Measured at 50°C [122°F] and viscosity of 32 mm2/s [148 SUS].

Special requirements to be briefly specified

4/2 WAY AUTOMATIC DIRECTIONAL VALVES PKV-...-T (NG 6)

Operation Hydraulic symbol

About the spindle for the PKV-6-T-G valves:

Connection diagram and connecting dimensions to ISO 4401.

4 x fixing screws M5x30 to DIN EN ISO 4762-10.9 must be ordered separately.

P-Q Performance curves

Special requirements to be briefly specified

4/2, 4/3 WAY DIRECTIONAL VALVES KV (NG 6, 10)

• Direct hydraulically operation.

Operation Hydraulic symbols

Pilot supply pressure min. bar [PSI] 10 [145]

1. Threaded connection X (Y) - G1/4 1. Threaded connection X (Y) - G1/4

Required quality of the

If flow rates greater than permissible occur during change-over, a cartridge

P-Q Performance curves

2/2 WAY DIRECTIONAL VALVES KV (NG 6)

Operation Hydraulic symbols

3. Solenoid ’’b’’ MR-045.

P-Q Performance curves

Measured at 50°C [122°F] and viscosity of 32