12 11 10 9 8 7 6 5 4 3 2 1

C IMW INDUSTRIES LTD. 2009/10/20 REVISION HISTORY

DO NOT USE AS THE BASIS
FOR MANUFACTURE OR SALE OF REV. DATE BY CK. DCR# REFERENCE
H APPARATUS WITHOUT
PERMISSION. A 2009/10/16 BJN EDL N/A FIRST RELEASE BASED ON 205919 H

RECOVERY TANK SUBASSEMBLY

CENTER OF GRAVITY
600 LBS
STORAGE CASCADE
SKID CENTER OF GRAVITY
CENTER OF GRAVITY 5800 LBS
1100 LBS

68"
65 3/4"
G COMPRESSOR SUBASSEMBLY
G
CENTER OF GRAVITY
2400 LBS COOLER SUBASSEMBLY
41 1/8" CENTER OF GRAVITY
37 3/4" 2200 LBS
MAIN MOTOR
WIRING
PASSTHROUGH 25 1/4"

16 3/8"

0"
F F
MOTOR
CENTER OF GRAVITY

44 1/2"
45 1/2"

64 1/2"

80 1/2"
0"

8 1/2"

32 1/16"
1600 LBS

2 4
LIFT POINTS VIBRATION MOUNT WEIGHT DISTRIBUTION
SECTION A-A

E E

INTRINSIC
JUNCTION BOX AIR OUTLET
5 EC3 1/2"
EC4 1/2"
6

120V
JUNCTION BOX
EC1 3/4"
GAS OUTLET: EC2 1/2"
D D
DISPENSERS
1/2" TUBE 440V
7 JUNCTION BOX
95 5/16" EC7 1/2"
2" GAS INLET
COUPLER, NPT BALL VALVE 3
FLEX HOSE, ANSI 300# FLANGE
100 MESH STRAINER

C A A C
5" 3
15"
87"
1 11 10

128"

NOTES:
1. THE LOCATION OF THIS EQUIPMENT IS NOT NECESSARILY AS DEPICTED. THIS DRAWING IS NOT AN
EXACT SPECIFICATION TO THOSE ASSEMBLING THE PACKAGE.
2. THE LOCATIONS GIVEN FOR THE ELECTRICAL AND GAS CONNECTIONS ARE APPROXIMATE ONLY.
B ITEM QTY PART
3. COMPRESSOR MUST BE LOCATED ON A FLAT AND LEVEL CONCRETE FOUNDATION AS SPECIFIED IN
THE INSTALLATION SECTION OF THE USER MANUAL.
B
NO. NUMBER DESCRIPTION UOM SPEC. WEIGHT 4. ANCHOR BRACKETS ARE PROVIDED TO SECURE SKID TO ITS FOUNDATIONS. IMW RECOMMENDS
THAT ALL ANCHORS BE SET WITH THE EQUIPMENT IN PLACE. IMW ALSO RECOMMENDS THE USE OF
1 1 207190 SKID ASM SINGLE IMW50 44XT MOTOR W/ STOR EA n/a 1147.6 "HILTI" ANCHORS, DETAILS OF WHICH WILL BE PROVIDED UPON REQUEST. IMW DOES NOT ACCEPT
2 1 207188 ENCLOSURE ASM W/ RECESS-SINGLE IMW50 EA n/a 2058.3 ANY LIABILITY FOR ALTERNATIVE FASTENING METHODS OR THE THE QUALITY OR SUITABILITY OF
THE FOUNDATION. DIMENSIONING & TOLERANCING PER IMW Industries Ltd.
3 1 - INLET PIPING EA n/a 20.0 5. REMOVE LIFTING PINS BEFORE BOLTING DOWN SKID AND ENCLOSURE AND INSTALL SUPPLIED Chilliwack, BC, Canada
ASME Y14.5M-1994. U.S.O.:
4 4 203526-00 LIFTING PIN SOLID 12 IN LONG EA n/a 14.0 ANCHOR BRACKETS.
6. TO ENSURE ADEQUATE AIR MOVEMENT, NO WALL SHOULD BE CLOSER THAN TEN FEET FROM THE TITLE
5 1 321095 TANK REC VERT 130 GAL 400 PSIG EA HANSON TANK# 24-VJ-130-R 509.0 AIR INLETS OR OUTLETS SHOWN.
7. ALL ELECTRICAL CONNECTIONS WILL BE MADE THROUGH THE ELECTRICAL PASS THROUGH SHOWN.
COMPRESSOR IMW50-5125DA-200-3625-4AC-3
6 1 207151 COOLER SUBASSEMBLY 240098 EA n/a 2211.0
8. ELECTRICAL CLASSIFICATION INSIDE THE ENCLOSURE IS CLASS 1, DIV 1, GROUP D. UNITS INCHES X/X ±1/16
7 1 220077 IMW COMPRESSOR EA n/a 2403.6 9. ALL ELECTRICAL CONDUIT OR CABLE MUST BE SEALED FOR CLASS I, DIV. 1 GROUP D UPON EXITING FILE. NO.
THE CLASSIFIED LOCATION. FINISH 64 MICRO IN. .X ±.1 REF. STANDARD SIZE REV
8 1 - MOTOR 447T EA n/a 1951.1 240100
A INNER RADI .03 MAX. .XX ±.01 DR. BJN 2009/10/16
D DWG. NO.
MRP ID 240100
A A
11 1 204025 BELT GUARD SINGLE DRIVE IMW50-44XT EA n/a 15.9 OUTER .03 MIN. .XXX ±.005 CK. EDL 2009/10/19
12 1 321816 STORAGE COMPLETE SINGLE LINE 1250 WL EA n/a 5800.0 EDGE X 45° ANGLES ±.5 AP. SCALE 1:24 WEIGHT 16997.0 LBS SHEET 1 / 1

12 11 10 9 8 7 6 5 4 3 2 1