HCD-AZ1D

SERVICE MANUAL E Model

Ver. 1.0 2006.05

HCD-AZ1D is the Amplifier, DVD player, Tape

Deck and Tuner section in DHC-AZ1D.

This system incorporates Dolby1) Digital and DTS2) Digital Model Name Using Similar Mechanism NEW
Surround System. DVD
1) Manufactured under license from Dolby Laboratories. DVD Mechanism Type WXD
“Dolby” and the double-D symbol are trademarks of Section
Optical Pick-up Name DM3451-A (SF-HD65F)
Dolby Laboratories.
2) Manufactured under license from Digital Theater Systems, TAPE Model Name Using Similar Mechanism HCD-DV2D
Inc. “DTS” and “DTS 2.0 + Digital Out” are trademarks of Section Tape Transport Mechanism Type CMAL5Z220C
Digital Theater Systems, Inc.

SPECIFICATIONS

Amplifier section DIGITAL OUT (OPTICAL) (Square optical connector Tape deck section
The following measured at AC 120 V, 240 V, 50/60 Hz jack, rear panel) Recording system 4-track 2-channel stereo
DIN power output (rated): 40 + 40 watts Wavelength 660 nm Frequency response 40 – 13,000 Hz, using
(6 ohms at 1 kHz, DIN) PHONES (stereo mini jack): Sony TYPE I cassette
Continuous RMS power output (reference): accepts headphones of
50 + 50 watts 8 ohms or more Tuner section
(6 ohms at 1 kHz, 10% SPEAKER: accepts impedance of FM stereo, FM/AM superheterodyne tuner
THD) 6 ohms FM tuner section
Inputs Tuning range 87.5 – 108.0 MHz
TV IN (phono jacks): voltage 1 V, impedance Disc player section (50 kHz step)
47 kilohms System Compact disc and digital Antenna FM lead antenna
AUDIO IN (stereo mini jack): audio and video system Antenna terminals 75 ohms unbalanced
voltage 1 V, impedance Laser Semiconductor laser Intermediate frequency 10.7 MHz
47 kilohms (DVD: λ=650 nm, AM tuner section
MIC (phone jack): sensitivity 1 mV, CD: λ=790 nm) Tuning range 530 – 1,710 kHz
impedance 10 kilohms Emission duration: (with the tuning interval
Outputs continuous set at 10 kHz)
VIDEO OUT (phono jack): max. output level 1 Vp-p, Frequency response DVD (PCM 48 kHz): 531 – 1,602 kHz
unbalanced, Sync 2 Hz – 22 kHz (±1 dB) (with the tuning interval
negative, load impedance CD: 2 Hz – 20 kHz (±1 dB) set at 9 kHz)
75 ohms Video color system format NTSC, PAL Antenna AM loop antenna
COMPONENT VIDEO OUT: Antenna terminals External antenna terminal
Y: 1 Vp-p, 75 ohms Intermediate frequency 450 kHz
PB, PR: 0.7 Vp-p, 75 ohms

— Continued on next page —

DVD DECK RECEIVER

9-887-243-01 Sony Corporation
2006E1678-1 Home Audio Division
© 2006.05 Published by Sony Techno Create Corporation
HCD-AZ1D

General
Laser component in this product is capable of emitting radiation
Power requirements 110 – 120 V, 220 – 240 V exceeding the limit for Class 1.
AC, 50/60 Hz
Adjustable with voltage
selector
Power consumption 120 watts This appliance is classified as
Dimensions (w/h/d) (excl. speakers) a CLASS 1 LASER product.
Approx. 190 × 300 × The CLASS 1 LASER
335 mm PRODUCT MARKING is
Mass (excl. speakers) Approx. 6.1 kg located on the rear exterior.

Design and specifications are subject to change

without notice.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.

Notes on chip component replacement

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.

UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.

2
 HCD-AZ1D

TABLE OF CONTENTS

1. SERVICING NOTES ................................................ 4 7-3. Block Diagram — USB Section — ................................ 24

7-4. Block Diagram — AUDIO Section — ........................... 25
2. GENERAL ................................................................... 7 7-5. Block Diagram — PANEL/POWER Section — ............ 26
7-6. Printed Wiring Board — MAIN Section — ................... 27
3. DISASSEMBLY 7-7. Schematic Diagram — MAIN Section (1/4) — ............. 28
3-1. Disassembly Flow ........................................................... 10 7-8. Schematic Diagram — MAIN Section (2/4) — ............. 29
3-2. Top Cover, DC Fan .......................................................... 11 7-9. Schematic Diagram — MAIN Section (3/4) — ............. 30
3-3. AMP Board, AV Board, Tuner (FM/AM) ....................... 11 7-10. Schematic Diagram — MAIN Section (4/4) — ............. 31
3-4. MPEG Board ................................................................... 12 7-11. Printed Wiring Board — MPEG Section (Side A) — .... 32
3-5. MPEG Holder .................................................................. 12 7-12. Printed Wiring Board — MPEG Section (Side B) — .... 33
3-6. DVD Panel Tray .............................................................. 13 7-13. Schematic Diagram — MPEG Section (1/3) — ............ 34
3-7. DVD Loader (WXD) ....................................................... 13 7-14. Schematic Diagram — MPEG Section (2/3) — ............ 35
3-8. Optical Pick-up DM3451-A (SF-HD65F) ....................... 14 7-15. Schematic Diagram — MPEG Section (3/3) — ............ 36
3-9. Front Panel Section ......................................................... 14 7-16. Printed Wiring Boards — KEY Section — .................... 37
3-10. Cassette Mechanism Deck (CMAL5Z220C) .................. 15 7-17. Schematic Diagram — KEY Section — ........................ 38
3-11. KEY Board ...................................................................... 15 7-18. Schematic Diagram — MIC CONTROL Section — ..... 39
3-12. HP Board, MIC CONTROL Board ................................. 16 7-19. Printed Wiring Board — AV Section — ......................... 40
3-13. MAIN Board .................................................................... 16 7-20. Schematic Diagram — AV Section — ........................... 40
3-14. POWER Board ................................................................ 17 7-21. Printed Wiring Board — AMP Section — ..................... 41
3-15. Panel Cass ........................................................................ 17 7-22. Schematic Diagram — AMP Section — ........................ 42
7-23. Printed Wiring Board — POWER Section — ................ 43
4. TEST MODE ............................................................... 18 7-24. Schematic Diagram — POWER Section — .................. 44

5. MECHANICAL ADJUSTMENTS ......................... 19 8. EXPLODED VIEWS

8-1. Overall Section ................................................................ 55
8-2. Front Panel Section ......................................................... 56
6. ELECTRICAL ADJUSTMENTS .......................... 19
8-3. Chassis Section ................................................................ 57
8-4. DVD Mechanism Deck Section ...................................... 58
7. DIAGRAMS
7-1. Block Diagram — MPEG-1 Section — ......................... 22 9. ELECTRICAL PARTS LIST .................................. 59
7-2. Block Diagram — MPEG-2 Section — ......................... 23

3
HCD-AZ1D
SECTION 1
SERVICING NOTES

NOTES ON HANDLING THE OPTICAL PICK-UP MODEL IDENTIFICATION

BLOCK OR BASE UNIT – Rear Panel –

The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care. Parts No.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

DISC TRAY LOCK

The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped. Model Part No.
Procedure : E3 model 2-672-998-0[]
1. Press the ?/1 button to turn the set ON. SP model 2-673-001-0[]
2. Press the DVD u button to select “DVD”
• Abbreviation
3. Set disc on the tray, press the x button and the Z button E3 : 240 V AC Area in E model.
simultaneously for five seconds. SP : Singapore model.
4. The message “LOCKED” is displayed the tray is locked.
5. To release from this mode, press the x button and the Z
button simultaneously for five seconds again.
6. The message “UNLOCKED” is displayed and the tray is
unlocked.
Note: When “LOCKED” is displayed, the slot lock is not released by
turning power on/off with the ?/1 button.

• SERVICE POSITION OF THE TAPE CASSETTE MECHANISM DECK

MAIN board

Front Panel

Tape Cassette Mechanism Deck

(CMAL5Z220C)

4
 HCD-AZ1D

• HOW TO OPEN THE DVD TRAY MANUALLY

Insert the stiff wire in the hole. The lock is released and the DVD tray opens.

DVD tray

stiff wire
hole

• SERVICE POSITION OF THE DVD MECHANISM DECK

MPEG board

DVD mechanism deck

Draw out the flexible board

of the DVD mechanism deck
from this position.

5
HCD-AZ1D

• CAUTION ON HANDLING POWER CORD (SAFETY STANDARD)

When you remove or replace the power cord,
(1) Fix the power cord to the POWER board with a binding strap as before.
(2) Check that the single-sheathed portion of the power cord does not contact the transformer
even when the single-sheathed portion is pushed toward the transformer with a 200-g force.

single-sheathed portion
of the power cord

power transformer

6
 HCD-AZ1D
SECTION 2
GENERAL This section is extracted
from instruction manual.

List of button locations and reference pages

How to use this page Illustration number

r
Use this page to find the location of buttons and other TUNER/BAND qa (27, 28, 31)
parts of the system that are mentioned in the text. R R
Name of button/part Reference page

Main unit
ALPHABETICAL ORDER BUTTON DESCRIPTIONS

A–O P–Z ?/1 (on/standby) 1 (10, 40, 49)

AUDIO IN jack qg (31, 42, 43) PC/TV/AUDIO IN ql (31, 40, Z (open/close) 5 (13)
43) DVD NX (play/pause) 6 (13,
Cassette compartment qh (30)
31, 44, 49)
CD SYNC 9 (30) PHONES jack qj
> (go forward) 7 (14, 31)
Disc tray 4 (13) PLAY MODE ws (14, 18, 49)
x (stop) 8 (11, 14, 23, 28, 30,
DISPLAY 3 (36, 37, 38) PRESET EQ wa (32)
33, 44, 49)
Display window 2 PROGRESSIVE w; (23) z REC PAUSE/START (record)
MIC jack qf (32) Remote sensor wg q; (30, 33)
MIC LEVEL qd (32) TUNER/BAND qa (27, 28, 31) Z PUSH OPEN/CLOSE (eject)
TUNING + 7 (27, 29) qs (30)
TUNING – wd (27, 29) . (go back) wd (14, 31)
VOLUME +/– qk (14, 29, 30, 40, TAPE N (play) wf (30)
43)

1 2 3

4
wg 5
wf 6
wd 7
ws 8
wa 9
w; 0
ql qa
qs

qk qd
qf
qj qg
qh

7
HCD-AZ1D

Remote control
ALPHABETICAL ORDER BUTTON DESCRIPTIONS

A–O P–Z ?/1 (on/standby) 1 (10, 34, 49)

ANGLE 5 (21) PLAY MODE qg (14, 18) TV ?/1 1 (40)
AUDIO 4 (20, 32) PRESET + wk (27, 28) SLOW/SLOW y 8 (14)
CLEAR ef (18, 19, 24) PRESET – es (27, 28) M (fast forward) 9 (14, 30)
CLOCK/TIMER SELECT w; PRESET EQ wf (32) X (pause) 0 (14)
(35, 36) REPEAT eg (17) m (rewind) qa (14, 30)
CLOCK/TIMER SET w; (12, 34, M/m/</, qs (12, 14, 21, 43,
SEARCH 3 (19)
35) 49)
SLEEP qk (34)
DIMMER ej (36) DISPLAY wj (12, 21, 43, 49)
SUBTITLE wd (21)
DISPLAY qj (36, 37, 38) > (forward) wk (12, 14, 31, 34)
TAPE qh (30) x (stop) wl (11, 14, 23, 30, 44)
DVD eh (11, 12, 13, 16, 18, 23, THEATRE SYNC ql (41)
25, 30, 44) H (play)* ea (13, 30, 44)
TOP MENU qd (15) . (go back) es (12, 14, 31, 34)
ENTER qs wg (12, 15, 16, 18, 19, TUNER/BAND wa (27, 28)
21, 22, 24, 27, 34, 35, 43, 49) O RETURN ed (16)
TUNER MEMORY ws (27) -/-- ef
FM MODE eg (29)
TUNING + 9 (27, 29)
FUNCTION +/– 2 (11, 12, 13, * The H, number 5 and
TUNING – qa (27, 29)
16, 18, 23, 25, 30, 44) VOLUME + (TV VOL +)
TV e; (40)
MENU 6 (15, 16) buttons have tactile dots. Use
TV CH + wk (40, 41)
MUTING wh (14, 29, 30) the tactile dots as references
TV CH – es (40)
Number buttons* qf (15, 16, 18, when operating the system.
19, 24, 41) TV/VIDEO qk (40, 41)
TV VOL +/–* 7 (40)
VOLUME +/–* 7 (14, 29, 30,
34)

8
 HCD-AZ1D

Setting the clock

Use buttons on the remote for the operation.
1 Press ?/1 to turn on the system.
2 Press CLOCK/TIMER SET.
3 Press . or > repeatedly to set the
hour.
4 Press ENTER.
5 Press . or > repeatedly to set the
minute.
6 Press ENTER.
The clock starts working.
To adjust the clock
1 Press CLOCK/TIMER SET.
2 Press . or > to select “CLOCK SET,”
then press ENTER.
3 Do the same procedures as step 3 to 6
above.
Notes
• The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
• You cannot set the clock in Power Saving Mode
(page 36).

9
HCD-AZ1D
SECTION 3
DISASSEMBLY

3-1. DISASSEMBLY FLOW

• This set can be disassembled in the order shown below.

SET

3-2. TOP COVER, DC FAN 3-15. PANEL CASS

(Page 11) (Page 17)

3-3. AMP BOARD, AV BOARD,

TUNER (FM/AM)
(Page 11)

3-4. MPEG BOARD

(Page 12)

3-5. MPEG HOLDER

(Page 12)

3-6. DVD PANEL TRAY

(Page 13)

3-7. DVD LOADER (WXD) 3-9. FRONT PANEL SECTION 3-13. MAIN BOARD 3-14. POWER BOARD
(Page 13) (Page 14) (Page 16) (Page 17)

3-8. OPTICAL PICK-UP

DM3451-A (SF-HD65F) 3-10. CASSETTE MECHANISM DECK 3-11. KEY BOARD 3-12. HP BOARD,
(Page 14) (CMAL5Z220C) (Page 15) MIC CONTROL BOARD
(Page 15) (Page 16)

10
 HCD-AZ1D

Note: Follow the disassembly procedure in the numerical order given.

3-2. TOP COVER, DC FAN

7 top cover
5 five screws
(screw 3 × 6) qa four screws
4 screw
(screw 3 × 8)
(screw 3 × 10) a
9 screw
(screw 3 × 8)

3 screw
(screw 3 × 6)

2 screw qd DC fan q; two screws

(screw 3 × 10) (screw 3 × 8)
8 connector
b 3P (CN350)

6 a

1 screw
(screw 3 × 6)

qs cover heat sink

3-3. AMP BOARD, AV BOARD, TUNER (FM/AM)

1 two screws
4 connector (screw 3 × 10)
0 two screws 7P (CN102) 3 connector
(screw 3 × 8) 10P (CN108)
5 connector
qf four screws 3P (CN106)
qg AV board (screw 3 × 10)

qd wire (flat type)

16core (CN801A)

qa screw 2 two screws

(screw 3 × 8) (screw 3 × 10)
qs earth wire
7 AMP board
6 connector
5P (CN101)
9 three screws
(screw 3 × 10)
8 two screws
(screw 3 × 8)
qh two screws
w; rear panel (screw 3 × 8)

ql two claws qj wire (flat type)

qk tuner 9core

11
HCD-AZ1D

3-4. MPEG BOARD

3 wire (flat type)

24core (CN7) 4 wire (flat type)
16core (CN2)
7 two screws
(screw 3 × 8)
9 MPEG board
2 connector 5 connector
5P (CN9) 9P (CN3)
1 connector
6P (CN10)

8 6 wire (flat type)

12core (CN1)

3-5. MPEG HOLDER

3 MPEG holder

1 screw
(screw 3 × 8)

5 two screws 2 two hooks

(screw 2.6 × 8)

4 two screws
(screw 2.6 × 8)

6 holder

12
 HCD-AZ1D

3-6. DVD PANEL TRAY

3 two claws

4 DVD panel tray 1

stiff wire

3-7. DVD LOADER (WXD)

5 two screws 6 two screws

(screw 3 × 10) (screw 3 × 10)

7 DVD loader (WXD)

8 two screws
(screw 3 × 10)

9 two rear mecha holders

2 two screws
(screw 3 × 10)

q; DVD holder
4
3 two dowels

1 screw
(screw 3 × 10)

13
HCD-AZ1D

3-8. OPTICAL PICK-UP DM3451-A (SF-HD65F)

4 two screws

qa optical pick-up
DM3451-A (SF-HD65F)
5 two dumpers (traverse mech)

q; wire (flat type)

9 two dumpers 24core
(traverse mech)

8 holder (traverse mech) 7

3 belt (pulley)

1 Turn round the gear in the

direction of the arrow.

3-9. FRONT PANEL SECTION

4 connector
3 connector 3P (CN104)
8P (CN201)
2 connector
3P (CN202)
5 screw
(screw 3 × 8)
1 wire (flat type)
21core (CN501)

6 screw
(screw 3 × 8)

8 screw
q; claw (screw 3 × 8)
qa claw

9 screw
(screw 3 × 10) 7 screw
(screw 3 × 8)

qs front panel section

14
 HCD-AZ1D

3-10. CASSETTE MECHANISM DECK (CMAL5Z220C)

1 wire (flat type)

7core

4 cover cass deck DV2D

3 coating clip

2 four screws
5 cassette mechanism deck
(screw 3 × 10)
(CMAL5Z220C)

3-11. KEY BOARD

4 wire (flat type)

7core (CN602)
3 ten screws
(screw 2.6 × 8)

5 wire (flat type)

21core (CN601)

6 KEY board
1 four screws
2 holder mecha front (screw 3 × 10)

15
HCD-AZ1D

3-12. HP BOARD, MIC CONTROL BOARD

2 HP board

1 two screws
(screw 2.6 × 8)

4 mic knob

3 three screws
(screw 2.6 × 8)

5 MIC CONTROL board

3-13. MAIN BOARD

7 wire (flat type)

21core (CN501)
6 connector
3P (CN104)

5 wire (flat type)

12core (CN503) 8 MAIN board

4 connector
3P (CN202)

2 connector 1 two screws

11P (FW901) (screw 3 × 10)

3 connector
8P (CN201)

16
 HCD-AZ1D

3-14. POWER BOARD

2 four screws
(screw 4 × 8) 8 Remove the
q; POWER board
4 coating clip solderings.

3 coating clip

6 clamp

5 bushing cord
7 power cord

9 power transformer

1 connector
11P (FW901)

3-15. PANEL CASS

1
3 four claws

4 panel cass, window cass

17
HCD-AZ1D
SECTION 4
TEST MODE

Note 1: Regarding the notification symbol “R” PANEL TEST MODE

Because the number of the operating buttons of this product are • This mode is used to check the software version, FL, LED
limited, some operations require use of the operating buttons of and KEY.
the remote commander. When a specific operation requires use Procedure:
of the operating buttons of the remote commander, “R” is added 1. Press the ?/1 button to turn the set ON.
to the specific operating procedure in this manual. Example 2. Press the DVD u button to select “DVD”
MENU/NO “R” The MENU/NO button of remote commander. 3. Press three buttons x , [PRESET EQ] and TAPE N simul-
Note 2: Incorrect operations may be performed if the test mode is not
taneously.
entered properly.
In this case, press the ?/1 button to turn the power off, and 4. When the panel test mode is activated, all segments are turned
retry to enter the test mode. on.

COLD RESET VERSION DISPLAY

• The cold reset clears all data including preset data stored in • This mode is used check the model, destination, software
the RAM to initial conditions. Execute this mode when version.
returning the set to the customers. Procedure:
Procedure: 1. Press the ?/1 button to turn the set ON.
1. Press the ?/1 button to turn the set ON. 2. Press the DVD u button to select “DVD”
2. Press three buttons x , [PLAY MODE] and DVD u simul- 3. Press three buttons x , [PRESET EQ] and [TV] simultaneous-
taneously. ly, the model and destination are displayed.
3. The message “COLD RESET” is displayed and the set is reset.
DVD COLOR SYSTEM CHANGE OVER
TUNER STEP CHANGE • The color system can be changed over NTSC or PAL.
• A step of AM channels can be changed over between 9 kHz Procedure:
and 10 kHz. 1. Press the ?/1 button to turn the set ON.
Procedure: 2. Set the function to “DVD”.
1. Press the ?/1 button to turn the set ON. 3. Press the ?/1 button to turn the set OFF.
2. Select the function “TUNER”, and press [TUNER/BAND] 4. Press the x button and ?/1 button simultaneously. The set
button to select the BAND “AM”. will power on automatically.
3. Press the ?/1 button to turn the set OFF. 5. The message “COLOR PAL” or “COLOR NTSC” will be
4. Press the x and [TUNER/BAND] buttons simultaneously, displayed on the fluorescent indicator tube. The color system
and thus the channel step is changed over. is changed over.

SHIP RESET CD REPEAT 5 TIMES LIMIT RELEASE MODE

Procedure: Procedure:
1. Press the ?/1 button to turn the set ON. 1. Press the ?/1 button to turn the set ON.
2. Press the DVD u button to select “DVD” 2. Set the function to “DVD”.
3. Remove the disc. 3. Press three buttons x , Z , and DVD u simultaneously.
4. The message “NO DISC” is displayed. 4. The repeat all mark blinks and then repeat 5 times limit is
5. Press three buttons x , [PLAY MODE] and TAPE N si- released.
multaneously.
6. The message “SHIP RESET” is displayed and the set is reset.
The DVD function is activated.
7. To exit from this mode, press the ?/1 button and pull out the
AC plug.

DISC TRAY LOCK

The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Procedure :
1. Press the ?/1 button to turn the set ON.
2. Press the DVD u button to select “DVD”
3. Set disc on the tray, press the x button and the Z button
simultaneously for five seconds.
4. The message “LOCKED” is displayed the tray is locked.
5. To release from this mode, press the x button and the Z
button simultaneously for five seconds again.
6. The message “UNLOCKED” is displayed and the tray is
unlocked.
Note: When “LOCKED” is displayed, the slot lock is not released by
turning power on/off with the ?/1 button.

18
 HCD-AZ1D
SECTION 5 SECTION 6
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS

Precaution DECK SECTION 0 dB=0.775V

1. Clean the following parts with a denatured alcohol-moistened
swab: 1. Demagnetize the record/playback head with a head
record/playback heads pinch rollers demagnetizer.
erase head rubber belts 2. Do not use a magnetized screwdriver for the adjustments.
capstan idlers 3. After the adjustments, apply suitable locking compound to
2. Demagnetize the record/playback head with a head demagne- the parts adjusted.
tizer. 4. The adjustments should be performed with the rated power
3. Do not use a magnetized screwdriver for the adjustments. supply voltage unless otherwise noted.
4. After the adjustments, apply suitable locking compound to 5. The adjustments should be performed in the order given in
the parts adjusted. this service manual. (As a general rule, playback circuit
5. The adjustments should be performed with the rated power adjustment should be completed before performing recording
supply voltage unless otherwise noted. circuit adjustment.)
6. The adjustments should be performed for both L-CH and R-
Torque Measurement CH.
Mode Torque meter Meter reading 7. Switches and controls should be set as follows unless otherwise
2.94 – 7.84 mN • m specified.
FWD CQ-102C (31 to 71 g • cm)
Tape Signal Used for
(0.43 – 0.98 oz • inch)
0.15 – 0.59 mN • m P-4-A100 10 kHz, –10 dB Azimuth Adjustment
FWD
CQ-102C (2 to 6 g • cm) WS-48B 3 kHz, 0 dB Tape Speed Adjustment
back tension (0.02 – 0.08 oz • inch)
2.94 – 7.84 mN • m [Record/Playback Head Azimuth Adjustment]
REV CQ-102RC (30 to 79 g • cm)
Procedure:
(0.42 – 1.11 oz • inch)
0.15 – 0.59 mN • m 1. Mode : Playback
REV
CQ-102RC (2 to 6 g • cm) test tape
back tension (0.03 – 0.08 oz • inch) P-4-A100
6.86 – 17.64 mN • m (10kHz, –10dB) MAIN board level meter
FF/REW CQ-201B (71 to 143 g • cm) JK102
(0.98 – 2.49 oz • inch) speaker terminal
9.8 mN • m or more
FWD tension CQ-403A (100 g • cm or more) set +
(1.4 oz • inch or more)
–
9.8 mN • m or more
REV tension CQ-403R (100 g • cm or more)
(1.4 oz • inch or more)
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1 dB of peak.

L-CH output
peak level within
1 dB within 1dB

R-CH
peak
screw
position
screw
L-CH R-CH position
peak peak

19
HCD-AZ1D

3. Mode: Playback DVD SECTION

test tape
P-4-A100 MAIN board
[RF Level Check]
(10kHz, –10dB) JK102
speaker terminal Check the RF level when optical pick-up block is replaced.
oscilloscope
Connection:
L
set oscilloscope
R MPEG board

CN7 pin 8 (V-RF) +

CN7 pin wf (GND) –
Procedure:
Waveform of oscilloscope 1. Connect an oscilloscope to CN7 pin 8 (V-RF) and CN7 pin
wf (GND) on the MPEG board.
2. Turn the power on.
3. Set the test disc on the tray and press DVDu button to
in phase 45° 90° 135° 180° playback.
good wrong 4. Observe the waveform of the oscilloscope, and check that the
RF level is satisfied to specified value.

4. After the adjustments, apply suitable locking compound to [Test Disc List and Specified Value]
the parts adjusted. Use the following test disc on adjustment.
TEST DISC Specified Value
Adjustment Location: Record/Playback/Erase Head
CD YEDS-18 (Part No.: 3-702-101-01)
0.57 to 1.1 Vp-p
PATD-012 (Part No.: 4-225-203-01)
DVD SL (Single Layer)
NTSC : HLX-503 (Part No.: J-6090-069-A)
HLX-504 (Part No.: J-6090-088-A)
PAL : HLX-506 (Part No.: J-6090-077-A)
0.58 to 1.23 Vp-p
DVD DL (Dual Layer)
NTSC : HLX-501 (Part No.: J-6090-071-A)
HLX-505 (Part No.: J-6090-089-A)
PAL : HLX-507 (Part No.: J-6090-078-A)
Note: Do not use existing test disc for DVD.

Checking Location: MPEG board (Side A)

— MPEG Board (SIDE A) —

23
CN7 1 IC7
24 2

CN7 Pin 8 (V-RF)

CN7 Pin wf (GND)
adjustment screw

U2
IC6
Note: Refer to “ 3-15. PANEL CASS ” (see page 17)

[Tape Speed Check]

Procedure:
1. Turn the power on. IC4
2. Insert the WS-48B into deck.
3. Press the TAPE N button of deck.
4. Check the reading of frequency counter becomes 3000 ± 90
Hz.

Sample Value of Wow and flutter

W.RMS (JIS) less than 0.3%
(test tape: WS-48B)

20
 HCD-AZ1D
SECTION 7
DIAGRAMS
• Circuit Boards Location
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
For Schematic Diagrams. For Printed Wiring Boards.
Note: Note:
• All capacitors are in µF unless otherwise noted. (p: pF) • X : parts extracted from the component side.
50 WV or less are not indicated except for electrolytics and • Y : parts extracted from the conductor side.
tantalums. • f : internal component. MPEG board
• All resistors are in Ω and 1/4 W or less unless otherwise • : Pattern from the side which enables seeing.
specified.
• f : internal component. Caution:
• C : panel designation. Parts face side: Parts on the parts face side seen from
(Side A) the parts face are indicated.
Note: The components identified by mark 0 or dotted Pattern face side: Parts on the pattern face side seen from
line with mark 0 are critical for safety. (Side B) the pattern face are indicated.
Replace only with part number specified.
• A : B+ Line. • Indication of transistor. KEY board
• B : B– Line.
• Voltages and waveforms are dc with respect to ground C
under no-signal (detuned) conditions. Q These are omitted.
– MPEG Section –
B E MAIN board
No mark: DVD STOP
– Other Section –
No mark: FM
HP board
( ) : TAPE REC
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production B C E
tolerances.
These are omitted.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances. Q MIC CONTROL board
• Circled numbers refer to waveforms.
• Signal path.
B C E
F : AUDIO
d : TUNER These are omitted.
j : PB (TAPE)
a : REC (TAPE) POWER board
J : DVD/CD (AUDIO)
I : DVD/CD (DIGITAL)
: DVD (RF) AV board
h : TV IN
i : AUDIO IN
L : VIDEO
g : CD (RF)
r : COMPONENT
E :Y
: USB
N : MIC
• Abbreviation AMP board
E3 : 240 V AC Area in E model
SP : Singapore model

HCD-AZ1D
21 21
HCD-AZ1D
7-1. BLOCK DIAGRAM — MPEG-1 SECTION —

OPTICAL
PICK-UP BLOCK
DM3451-A
(SF-HD65F)

F- F-

F+ F+
IC6
T+ T+ FLASH MEMORY

T- T-

A 160 A
9,11,14,16
28-36,
18,19,22,24
B 162 B MDA0-15 38-45 DQ0-15
26,27,30,33
35,37,39,42
C 165 C

D 167 D MWR# 23 11 WE

E 170 E RESET# 141 12 RP

F 172 F
4-8,10,13, 1-9,
15,17,28,31, 16-25, A0-18
186 ICI05 MAD0-19 34,36,38,40,
48
43,45,46,
U2(1/2)
185 ICI04 48,49
RF AMP
FOCUS/TRACKING
ERROR AMP MCS#0 47 28 OE
171 K
MRD# 44 26 CE
168 J

Q4,11 176 CD-MD

VR-CD VR CONTROLLER
(CD)
188 IDI03
Q10
VR-DVD VR CONTROLLER
(DVD) 177 DVD-MD

VS 173 VC

V-RF 157 RFP

Q2
LD(DVD) POWER
179 DVD_LD

IDI04/PWNCO6
CONTROLLER

IO46/PWNCO5

IO43/PWNCO2

IO45/PWNCO4
I04/PWNCO0
(DVD)

Q21

IO32
LD(CD) POWER 178 CD_LD
CONTROLLER
(CD) 183 200 201 202 195 198

+3.3V
F-
13 VOFC- STBY 28
F+ Q16
14 VOFC+ VINSL- 5 +5V
+3.3VREG
OPEN SW TOP T+
15 VOTK+
TCL CF CERR1 2
CLOSE SW T-
16 VOTK- +1.8V
IC7 Q17
LOAD+ 10 PLHD CF CERR2 3
MOTOR +1.8VREG
LOAD- 9 PVCC1 DRIVER
CTKERR1 25
SLED+ 12 VOSL+
VINSL+ 4 • Signal Path
SLED- 11 VOSL-
HOME SW : DVD(RF)
VINFC 1
SPIND+ 17 VOLD+
SPIND- 18 VOLD- VINTK 26 : CD(RF)

PANEL/POWER VINLD 23
SECTION D OPN
7 V/VFFC
(Page 26)
CLS
PANEL/POWER C 6 VOSL
SECTION
(Page 26)

HCD-AZ1D
22 22
 HCD-AZ1D
7-2. BLOCK DIAGRAM — MPEG-2 SECTION —

IC14
EEPROM IC501(1/4)
SYSTEM CONTROLLER

SDA
SCL
5 6 8 VIDEO SW

135 136 137

XO 143

IC031

IDI02
IC103//VIDO
Y1
GCLK 144 27MHz

PANEL/POWER JK803A
DSSTB
SECTION E DSCK
1 SSCTXD/IO17
207 IO47/SSCCLK
CVBS/C 150
CVBS/C/Y 148
Y
(Page 26) Y
DSDA
208 IO16/SSCTXD V/R/Y 151
MRST PB/CB
141 RESET# C/B/V 153 PB/CB COMPONENT
VIDEO OUT
PR/CR
PR/CR

JK801
VOUT
VIDEO OUT
U2(2/2)
VIDEO DAC ENCODER

JK804A
TX
DIGITAL OUT
SPDIF 110
OPTICAL

U4
AUDIO DAC

AB CLK 116 2 SCLK

AMCLK 118 4 MCLK
ALR CLK 115 3 LRCK

RADD1-10
RDAT0-15 AOUT O 113 1 SDATA
IC8
RDQM#
RCS#O

RRAS#
RCAS#

RCS#1
RWE#
RBA0
PCLK

AUDIO
82,84-86, 53-57,59,60,
AOUTL 8 2 AMP 1 B SECTION
AOUTR 5 R-CH (Page 25)
70 71 80 77 75 74 78 73 88-90,92,94,96, 61,63,65,67
98-100,102-104
PCLK
RCSO

RCS1
RCAS
RWE

RDQM
RBA0

RRAS

DAT0-15 ADD1-10

• R-CH is omitted due to same as L-CH.

• Signal Path

RCS1

RDQM
RRAS
PCLK
RBA0

RCAS
RWE
DAT0-15 ADD1-10 DAT0-15 ADD1-10
: DVD/CD(AUDIO)
2,3,5,6,8,9,11, 20-24, 2,3,5,6,8,9,11, 20-24, : DVD/CD(DIGITAL)
18 19 35 15 16 17 14 36 12,39,40,42,43, 19 18 35 15 16 17 14 36 12,39,40,42,43, 27-32
27-32 45,46,48,49
45,46,48,49
: VIDEO
A11
CLK
WE
CAS
RAS
LDOM
UDOM

A11
CS
CLK
WE
CAS
RAS
LDOM
UDOM
CS

A0-A10
D0-D15
A0-A10
D0-D15

: COMPONENT
:Y
IC4 IC5
SDRAM SDRAM

HCD-AZ1D
23 23
HCD-AZ1D
7-3. BLOCK DIAGRAM — USB SECTION —

JK201

L
TV IN

R R-CH

JK601

R-CH
AUDIO IN

IC402
QUAD ANALOG IC403
SWITCH QUAD ANALOG
SWITCH
IC401
USB I/F
DA CONVERTER

1 I1 O1 2 1 I1
J401

USBVCC
21 HOST VOUTL 14 4 I2 O2 3 4 I2
USBBD- O1 2
8 D-
AUDIO
PC USBBD+ 9 D+ VOUTR 15 R-CH
Q405 Q410 F SECTION
MUTE MUTE (Page 25)
USBGND DGND O2 3
6

Q402 5 C2 Q407 5 C2
SWITCH SWITCH

Q413 XT0 1 6 C3 6 C3
USB MUTE
X401 Q403,404 13 C1 Q408,409 13 C1
12MHz SWITCH SWITCH

XT1 28 12 C4 12 C4
Q401,412
USB MUTE

Q414
USB MUTE

43 64 58 57
R-CH is omitted due to same as L-CH.

AUXTUS
PCON
U-SENS

USB PS
Signal path

:USB
IC501(2/4)
SYSTEM CONTROLLER
:TV IN

:AUDIO IN

HCD-AZ1D
24 24
 HCD-AZ1D
7-4. BLOCK DIAGRAM — AUDIO SECTION —

IC302 IC103
MPEG-2 SOUND PROCESSOR POWER AMP
JK104
SECTION R-CH
USB (Page 23) B 21 CD-L OUT-L 18 11 CH1_ CH1_ 4 PHONES
IN OUT+
SECTION F 19 AUX-L
(Page 24) IC250(1/2) Q102 Q104,301
MIC AMP 23 TUNER-L 13 STBY
JK202 MUTE OVER LOAD
IC250(2/2)
3 5 DETECT
+ 1 + 7 MIC AMP IC201 7 VOL-IL
MIC
2 - 4 - AMP

2 TAPE-L R-CH

+9V(TU) Q199 L JK102

MIC LEVEL VR250 Q322 INVERTER
STRB 52 MUTE CONT 13 COMT SPEAKER
REC-O-L 28
IMPEDANCE
IC501(3/4) R-CH USE 6Ω
SYSTEM CONTROLLER Q321 INH R-CH
A Q319
MUTE CONT MUTE
MUTE R
IC503 SWITCH
SDAT/ROMDA 53 5 SDA PANEL/POWER
TUNER PACK EPROM SECTION
SCK/ROM CK 54 6 SCL
(Page 26)
L-CH
R-CH R-CH AMUT 59 Q105
MUTE CONT
FM 75Ω D OUT 19 TUDO Q308
Q314,317 Q303,304,354
COAXIAL D IN 18 TUDI TSOL 5 +VDD CURRENT PROTECT DC PROTECT
DETECT SWITCH R-CH
CL 20 TUCK TMOT 6 Q350-352 DC
ANTENNA
CE 12 TUCE TCNT 7 FAN CONT FAN
AM SO 11 STE REPT 31
HDPN 30

RPHD 3 Q353,355
BIAS 4 FAN CURRENT
DETECT

TAPE
MECHANISM
DECK
Q327,332
REC/PB SWITCH
L-CH

REC/PB
• R-CH is omitted due to same as L-CH.
HEAD
R-CH
• Signal Path
Q329-331
R-CH REC/PB SWITCH : AUDIO

R-CH T301 : PB(TAPE)

Q344-Q347 : REC(TAPE)
Q348
OSC
ERASE
: TUNER

+VM : DVD/CD(AUDIO)

: TV IN
PACK
RECF : MIC
RECR
HDPLY

TCNT

MOT Q653,654
MOTOR DRIVER

SOL Q651,652
SOL DRIVER

HCD-AZ1D
25 25
HCD-AZ1D
7-5. BLOCK DIAGRAM — PANEL/POWER SECTION —

IC501 (4/4)
SYSTEM CONTROLLER

IC651 PT901
VFD651 POWER
FL DRIVER
TRANSFORMER(MAIN)
SEG1-SEG24 14-29, VF
VFSTB 17 9 STB 31-38
VFCK 16 8 CLK VF
FLUORESCENT
VEDA 15 7 DIN GRID1-4 42-39 INDICATOR
TUBE VF

Q315 D306
VF -33V(VPP) -33V
VEE 30 -33V(VPP)
REG
VDD 13 VDP D309
Q601 Q306 D301
D601-D604
SWITCH
LED1 1 LED Q305,Q320
DRIVE D324 POWER AMP B+
S667,S651-654,S657 POWER
Q602 CONTROL
D605-D608 AUDIO INH
FUNCTION SECTION A
28 KEY3 LED2 2 LED MUTE POWER AMP B-
KEY
DRIVE (Page 25)
D302
+VDD
S665,S666,S656,S658,S659
IC301
FUNCTION +5V
27 KEY2 D +5V 2 REG 1
KEY
Q502 5
D652
LED I/ Q318
S655,S660-664 LED 60
DRIVE SWITCH
Q311,312
FUNCTION
26 KEY1 +12V
KEY +12V(VM) REG
Q309,310
PCON 64 SWITCH Q316
+9V
+9V REG
Q198
INH 44 +9V
IR651 +9V (TU) REG Q313
REMOTE
CONTROL 1 45 REM +10V REG
RECEIVER
TUON 61 Q196,197
SWITCH
37 XT2 D319 - D321
X501
32.768kHz IC101
38 XT1 +6V
+6V REG
40 X2
X502
8.38MHz
41 X1
CD ON 62

RY901

MPEG-1 CLS
SECTION C OPN
56 CLS
Q307
(Page 22) 55 OPN
RELAY
RLY 63
DRIVE

Q507 +12V(VM)
MPEG-1 TOP VDP
SWITCH
SECTION D TCL
14 TOP
D501 PT902
35 TCL POWER
(Page 22) FPON 23 D901-904 TRANSFORMER (SUB) SW901
VOLTAGE AC IN
Q504-506 SELECTOR
IC502 +5V
MPEG-2 DSCK D503 +5V REG
SECTION E DSSTB
50 DSCK
RESET
49 DSSTB RST 36
(Page 23) SWITCH
DSDA
48 DSDA
MRST D906 D907
47 MRST
AVR 34

SFTY 29

HCD-AZ1D
26 26
 HCD-AZ1D
7-6. PRINTED WIRING BOARD — MAIN SECTION — • See page 21 for Circuit Boards Location.

1 2 3 4 5 6 7 8 9 10 11

A MAIN BOARD MPEG BOARD

CN1
B L MIC CONTROL BOARD
CN603 TUNER
for DOWN LOAD (Page 33) (Page 37)

• Semiconductor Location
5
8 2 8 2 1 Ref. No. Location Ref. No. Location
9 L411 3 2 J401
7 1
E
L412 PC D105 G-9 Q196 B-9
1 4

R407
R406
2
1 D106 C-10 Q197 B-9
B 6 D107 C-10 Q198 B-8

L414
L415
IC501 49 48
1 11
E
E
C439
D196 B-9 Q199 B-9
12 D198 B-8 Q305 J-4
2 R405
C MPEG BOARD
CN3 D199 B-8 Q306 I-2
E 64 33 E (Page 33) D301 I-5 Q307 H-3

C120
1 32 1 D302 I-3 Q313 G-8
A 20 E 8 5 C232
9
D305 G-5 Q315 I-3
21 R118 L
16 17
KEY BOARD 1 4 D306 I-3 Q316 H-3

C100
JK201

C132
C CN601
3
D307 I-2 Q317 H-5
IC101 IN TV

C105
(Page 37) D308 H-3 Q318 G-5
IC502
1

D405
E Q412 Q401
R D309 J-4 Q319 J-3
SFTY R218
8
5 4
D310 H-2 Q320 J-4
4
IC503 C411 R404
D312 G-9 Q321 G-5

E
1 R417
3 E
E
E

R401
C403
1 R419 C416 C413

C409 R415
R423 D313 G-5 Q322 G-5

R432
R433
C414 R424

C404 C405
C406
D314 G-9 Q326 G-3

JR405
C415 R442
AMP BOARD

L403
IC401
E C436 15 14
R418

D404
R455 CN106 D317 G-9 Q327 G-3
D C419 R456

L401
R434
E
C412
C420
C410
R457
R458 +
(Page 41) D318 G-2 Q328 G-3

R459
28
D319 F-7 Q329 G-3

R403
Q409 1 C438 FB401
R428

R427
JR402

R435
Q E R431 C422 R421 R408 CN105
D320 F-7 Q330 G-3

R422
C407
Q347 E R429 C418 X401 Q413 JK102
E C421 1 L
2

R438
JR401
R416

R441
C402 C401

R444

R447
D321 F-7 Q331 G-3
1
R430 E

C440
Q406
Q411 R426

E
7 8
TAPE E Q408 E E 3 D323 I-7 Q332 G-3

C437
8 14
E E Q405 E C430 –

D406
MECHANISM Q410 Q414 D324 J-4 Q344 F-2
IC403 R425

R437
R436
L409 R420
SPEAKER
DECK
R451 E
C417 R412 Q402
E IMPEDANCE USE 6Ω
D325 H-4 Q345 F-3

R410
HEAD R413 R409

E (REC/PLAYBACK/ERASE)
R218A
7 1
R445
D401 D330 C-8 Q346 D-3
A Q407 L410 L408
1 14 E D401 E-7 Q347 D-3
E

R411
R439
R440
A L407
–
1 C425
A C426 R414 Q404 D404 D-6 Q348 E-3

R220A
E R120A L405 Q403
L-CH 2 E
D405 C-7 Q401 D-7
IC402
R118A
REC/PB 3 R
HEAD R-CH 4 D406 E-7 Q402 E-7
5 E
6 E + D501 G-5 Q403 E-7
ERASE 7
HEAD 8
D502 D-3 Q404 E-7
D503 C-3 Q405 E-6
F D505 D-2 Q406 D-6
D507 F-5 Q407 E-5
D508 H-3 Q408 D-5
8 1
IC302 1 Q409 D-5
E IC101 C-8 Q410 E-5
E IC201 G-3 Q411 D-5
H
E

E E IC301 H-5 Q412 D-7

R266

AMP BOARD IC302 F-4 Q413 D-8

G E E
R249
E
E 10 CN108 IC401 D-7 Q414 E-8
IC402 E-6 Q502 C-3
R264

3 E (Page 41)
C221 R265 R263
C259 5
R246 C220
4 R247
IC403 E-5 Q504 D-3
1
IC501 B-4 Q505 D-3
R267

R248
C261
C262

C260
R268

8 1
CN 202 1 5 IC502 C-3 Q506 D-3
IC201 E
K IC301
IC503 D-5 Q507 C-3
MIC
H CONTROL
BOARD
E
E
CN250
(Page 37) 7
1

E I
1 AMP BOARD
I CN102
E (Page 41)

11

E
E K K A
A

K
E A

J
(CHASSIS)

D POWER BOARD
FW901
(Page 43)

HCD-AZ1D
27 27
HCD-AZ1D
7-7. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • See page 45 for Waveforms. • See page 48 for IC Pin Function Description.

TUNER
TV
IN
( ) R L

SO
_
MAIN BOARD (1/4)
+9V REG
9P 10 12.4

10.7 SWITCH
10.7 10.7 1000P

1000P

120K

120K
1000P
V
1000P
3.1 0
INVERTER
0

1200P

1200P
R218

SWITCH
2.2K
3.4
3.8 0.6 R118

V
2.2K

V
V
V

V
30
MAIN BOARD
IC501 VOLTAGE CHART
21P
31
32
3 (4/4)
PIN.No Voltage PIN.No Voltage (Page 31)

V
1 4.9 41 2.8
2 4.9 42 -
3 4,9 43 0
4 0 44 4.9 0.01
5 0 45 4.9
6 0 46 0
7 0 47 4.9
8 0 48 3.2

47K

LED DRIVER
9 - 49 3.4 B

10 5 50 4.8 A 5

KEY

+5V REG
11 0 51 0.3

+5V REG
0.6

0.01
0.3
12 0 52 0
BOARD 0.3

13 0 53 4.9 5.7
0.7
CN601

270
14 4.8 54 4.9
15 0 55 0
(Page 38) IC501 11.3
10.6 10.3 0.2

SYSTEM CONTROLLER +5V REG

1K
16 0 56 0
17 4.9 57 4.9
1000P
18 0 58 0
19 0.3 59 4.9 5
20 0 60 0 5
0.01

0.01

2.7K
21 0 61 0 SWITCH
4.2
22 4.9 62 4.9
R587 0
23 0.2 63 4.9
24 5.1 64 4.9
for DOWNLOAD

25 -

V
26 5
27 5 7 8
4.9
28 5
CN502 5
29 2.8 8P 4.9
5
30 3.8 5

31 3.8 IC503
EP ROM
32 0.4 IC502
RESET SWITCH
33 0
34 5
35 0
36 5
B
37 3.3 MPEG
38 2.4 BOARD(1/3)
39 0 CN1
40 3 (Page 34)
No mark:FM
12P ( ):REC

13
10
2

7
8
9
1

3
4

6
MAIN BOARD
(2/4) 1
(Page 29)

HCD-AZ1D
28 28
 HCD-AZ1D
7-8. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • See page 45 for Waveform. • See page 46 for IC Block Diagram.

1 MAIN BOARD (1/4)

(Page 28)

10

13
6
2

7
8
9
1

3
4
MAIN BOARD (2/4) IC302
SOUND
PROCESSOR 34
IC B/D 33

4 MAIN
BOARD
(4/4)
TAPE 35
(Page 31)

3300P
3300P
MECHANISM

C125

C225
14
DECK 10K
15
(REC/PB/ERASE) 8P 10K

IC201 16
AMP 17
0.018
LCH
REC/PB 18

0.018
HEAD 19
-4.5 0 0
RCH 0
20

F
V
0 0 21
0 0 0 0 0 0 0 0 0 0 0 0
IC301
ERASE +5V REG
4.5
0 0 0 16.5

5.1
22 2 MAIN BOARD
(3/4)
0 0 0 0 0 0 0 0 0 0 0 4.6 -4.5 -4.5 (Page 30)

0
V
C107

SWITCH

0.01
0
IC101 0.6
NJM7806FA
0
0
SWITCH 0.6 SWITCH

10
16 16 6 9 C100 IC101
C105
+6V REG

0(-6.2) 0.6

1.9(-11.7) 0(6.1) 23
9
S 0(6.2) 0(9.6)
0 1.9(-11.9) 9.8
S 24
2.2(0) 0(0.4)
9.8(8.9)
0(6.8)
0(-6.2)
2.2(0)
0(6.1) 0
9.8(0)
2.2(-11) SWITCH
0
2.1(-6.6) 0(0.4)
S 1.9(-11.9) 0(2.1)
2.1(-6.5)
0 0 Q344~Q347
Q329~Q332,
Q326,Q327 BIAS OSC
0 REC/PB SWITCH

2.1(-6.5)
JR101
0 No mark:FM
( ):REC

CN202
3P/2.0

+ 10V
MIC
AGND
MIC CONTROL MPEG BOARD
K BOARD C (3/3)
CN250 CN3
(Page 39) (Page 36)

HCD-AZ1D
29 29
HCD-AZ1D
7-9. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) —

AMP
AMP
H BOARD
I BOARD
CN108
CN102
(Page 42)
(Page 42)

MAIN BOARD (3/4)

AMP
E BOARD
CN106
(Page 42)

L
+ L
0.01 GND
- SPEAKER
0.01 GND
- R
5 36 R
+
(IMPEDANCE USE 6 )

1000P

1000P
MAIN BOARD
0.1
(4/4)
(Page 31)

( )

MUTE SWITCH 0
0

0 POWER
CONTROL

3.8 0.6
0
0.6
0
SWITCH

POWER
CONTROL

6 37

MAIN BOARD
(4/4) 11P
(Page 31)

14
15

16
9.8
CURRENT DETECT

17 11
D
+9V REG

16.7
18 POWER BOARD
19 16.3 8.8 FW901
10.8
20 (Page 44)
2 21

MAIN BOARD
(2/4)
(Page 29)
22 -32.9
-38.6
23 -32.4

24 -33V REG

16.6
16.5

RELAY
0 DRIVE
CURRENT
DETECT 0
4700P

7 21 4.5

MAIN BOARD
(4/4)
(Page 31)

No mark:FM
( ):REC

HCD-AZ1D
30 30
 HCD-AZ1D
7-10. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • See page 46 for IC Block Diagram.

PC

MAIN BOARD (4/4)

Q401,Q412
Q413,Q414 USB I/F
USB MUTE IC401 DA CONVERTER IC B/D
MTZJ3.3A
C437 0.1U

3.3 10V
IC402

A
3.3 QUAD ANALOG
SWITCH

JW
JW
A 8.4

0
INVERTER
0 IC B/D
0

9.8
A
SWITCH

9.7
0
C440

10V
1000P 0

A
2
FB401 SWITCH
Q405,Q406

15K
MUTE
6 37
2
0

MAIN 0

V
BOARD(3/4) Q413
0 V 50V A
DTC114YK
(Page 30) R442 22K
15K
0 0
C419

8
V
50V
0 1
V
4.9

MAIN 7 21
MA01
+ 2
L MIC CONTROL

C417 470P
PON
3
BOARD Q414
V BOARD

39K
CN603

R418

R431
DTC114YK
(3/4) L405
0
(Page 30) (Page 39)

30

R220A 120K R218A

R120A 120K 2.2K
R118A
2.2K

0
8.4 IC403

JR401
INVERTER QUAD ANALOG
SWITCH
IC B/D
0

9.8
36 5 MAIN
Q408
DTA114YKA
9.7 IC401,IC402,IC403 BOARD(3/4)
3 0
VOLTAGE CHART
IC401 IC402 IC403
(Page 30)
0
MAIN Pin No Voltage(V) Pin No Voltage(V) Pin No Voltage(V) Pin No Voltage(V)

BOARD(1/4) 1 3 15 0 1 0 1 0
2 - 16 3.3 2 0 2 0
(Page 28) 2 3 3.3 17 0 3 0 3 0
Q408, Q409 4 - 18 0 4 0 4 0
SWITCH 0 5 - 0 5 8.4 5 8.4
19
6 0 20 3.3 6 8.4 6 8.4
2
7 3.3 21 0 7 0 7 0
A
100K
R439

50V MUTE 8 0 22 0 8 0 8 0
0
9 0 23 0 9 0 9 0
10 3.3 24 0 10 0 10 0
100K
R444

50V A 11 0 25 3.3 11 0 11 0
MUTE R447 R451
32 100K 100K 12 0 26 3.3 12 0 12 0
13 3.3 27 0 13 0 13 0
31 9.8 9.8
14 0 28 3 14 14
35
M
4 33
No mark : FM
MAIN 34 ( ):REC

BOARD(2/4)
(Page 29)
N

HCD-AZ1D
31 31
HCD-AZ1D
7-11. PRINTED WIRING BOARD — MPEG SECTION (SIDE A) — • See page 21 for Circuit Boards Location.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

OPTICAL
PICK UP
A BLOCK
MPEG BOARD (SIDE A) DM3451-A (SF-HD65F)

• Semiconductor
Location
B Ref. No. Location
D2 F-4
14 8 7 1
IC4 K-7
IC6 H-4
IC7 IC7 C-11
C IC8 I-11
IC14 G-11
15 21 22 28
Q2 E-7
24 Q4 D-9
Q5 E-11
D Q7 D-11
Q10 D-9
E
Q11 D-8
Q21 E-7
E E E E
Q22 D-11
Q23 E-11
E E
E E U2 H-7
E
U4 I-10

C150

F
1 2 208 157

3 1
156

G
48 25 4 1

IC14
5 8
H U2
IC6
4 1

IC8
I 1 8
1 24
52 105
U4 5 8

4 5
53 104

25 1

IC4

26 50
K

HCD-AZ1D
32 32
 HCD-AZ1D
7-12. PRINTED WIRING BOARD — MPEG SECTION (SIDE B) — • See page 21 for Circuit Boards Location.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

A
for Down Load
MPEG BOARD (SIDE B)

• Semiconductor
Location
B Ref. No. Location
D3 J-12
D7 J-3
+
D10 F-12
D12 D-3
C IC5 K-8
+ Q16 C-2
E Q17 J-5
+

D 1 +

1
2 +

E + +
+
+
F
AV BOARD
CN801A +
(Page 40)

151
F
+
15
16

+
1
H +
DVD
+ MECHANISM
+ DECK
+

I +
+ +
67 1

+
DVD
J + + E
MECHANISM
+ DECK
50 26
+
6

IC5
9 1 +
12 2
1 25
11 1
K

C B
MAIN BOARD MAIN BOARD
CN302 CN503
(Page 27) (Page 27)
HCD-AZ1D
33 33
HCD-AZ1D
7-13. SCHEMATIC DIAGRAM — MPEG SECTION (1/3) — • See page 45 for Waveforms. • See page 50 for IC Pin Function Description.

1
MPEG BOARD (1/3) 2
3
1
MPEG
4
BOARD(3/3)
(Page 36)
0.01
0.01

3.3
3.3

3.3
3.3

3.3
3.3
3.3

3.3
3.3
3.3

3.3

3.3
3.3
3.3

3.3
3.3
3.3

3.3
3.3

3.3
3.3

3.3
0

0
0.01
0

1.8
1.8
2 1.8
0 1.8
1.8
0 0.01
0
1.8
0
0
for DOWN LOAD

0
0.1 0
1000P 0.027 1000P 1000P 0

0.2
0.1 0.1
0.2 0.1

3.3 2.4
0
3.7 5
0
0
0 6
3.3
0
2
3.3 1.3
7 MPEG
1.8K 0
0
1.3 BOARD(3/3)
ZR36862 TQFP-208 2.2
2.1 (Page 36)
1000P 1000P 1.3
3.3

B 0 3.3

1000P
MAIN 3.3
3.3
1.3

BOARD(1/4) IC6 3.3 1 0 1000P

CN503 FLASH MEMORY

1.2
(Page 28)
0
0
6 3 4
0 5 1.7
0 2.3
0 2
SST39VF800A 70-4C 0 0
3.2 3.3
0
0 0
2.8 0
0.9 1.8
3.3 3.2
3 0
3.3 3.2
0
3.3 0
0 0
0.3
3.3 3.7
2
0 0
2.2
0 0
1.1 0
0 3.2
3.3 3.3
3.3 3.2
2,2
3.3 0
0
3.3 0
0
3.3 0
0
3.3 0
0
0 0
3.3 0
3.3 1000P
0
0
0 3.3
3.3 3.2
U2
3.3 0 RF AMP
3.2
0 0 2.3
FOCUS / TRACKING 4.7K
0 2.2 ERROR AMP 12
JR
3.3 2.2 VIDEO DAC ENCODER 0
2.4 0 10
3.7
2.5 0
3.3
3.3 0 11 3
0 3.3
1.4 9
2.3 MPEG
2.5
4.7K 0.9
0
8 BOARD(3/3)
0
0 0
(Page 36)
0.1

4.7K 1000P
4.7K
0.7

3.3
3.3
3.3
3.3
0.7
3.3

3.3
0
0
0
0
0
0
0
0
0
0

0.4
0.4
0.4
0.5
1.4

3.3
1.4
0.4

0.6
3.3
0.5
3.3
0
0

1.2
0
5 0.1 4.7K
0
3.3
3.3

AT24C0

IC14
EEP ROM
3.3
3.3
1.5

3.3
3.3
3.3

0.7
0.5
0.5
0.8
0.8
0.8

0.2
0.2

0.2

3.3
1.5

3.3
0.7
0.5
0.5
0.8
0.8
0.8

0.2
0.2

0.2

3.3
3.2

3.3
3.3

3.3
3.3
3.3
3.3
3.3
3.3
3.2
3.3
3.3
3.3

3.3
3.
0
0

0
0

0
0
0

0
0

IC4 IC5
SD RAM K4S161622H K4S161622H SD RAM
1.2
1.1
1.2
1.1
1.5
1.1
1.5
0

1.2
1.1
1.2
1.1
1.5
1.1
1.5
0.8
0
1.2
1.2

0.7
1.4
1.3

1.3

0.8
0.7
1.3
1.4
1.2
0
0

1.2

1.3

No mark : DVD STOP

14

13
4 5
MPEG MPEG
BOARD(2/3)
BOARD(2/3)
(Page 35)
(Page 35)

HCD-AZ1D
34 34
 HCD-AZ1D
7-14. SCHEMATIC DIAGRAM — MPEG SECTION (2/3) —

MPEG
4 MPEG BOARD(1/3) 5 MPEG BOARD(1/3) 6
BOARD(3/3)
(Page 34) (Page 34)
(Page 36)

13
14

15
16
MPEG BOARD (2/3)

4.1 3.3

855D 3.3
+3.3V REG

3.6 1.8

6.8

855D 3
DVD +1.8V REG
MECHANISM
DECK 4.7K

0.022 0.1
AM5888S
0 2.8

1.3 1.7 0 3.3

2N3904
1.3 1.7 0.7
4.7K 3.1
1.7 7.1
Q2
0.1 3.3K 0
1.3 POWER
CONTROLLER
0 1.7 IC7 Q4,11 (DVD)
0 MOTOR VR
DRIVER CONTROLLER 0
OPTICAL
PICK-UP 7.1 7.1 (CD)
0.7
BLOCK 0
DM3451-A
0 3.3
(SF-HD65F) 7.1 0.1 2N3904
0 2.7 3.1

3.6 2.7
0
3.6 3.6 0 Q21
0.7 POWER
0 3.6 CONTROLLER
2.2K
2N3904 (CD)
VR CONTROLLER
1000P

(DVD)
0.1

0.1
0.1

0.1

No mark : DVD STOP

HCD-AZ1D
35 35
HCD-AZ1D
7-15. SCHEMATIC DIAGRAM — MPEG SECTION (3/3) —

MPEG BOARD (3/3)

1
2
3
MPEG 1
BOARD
(1/3) 4
(Page 34)

5
6
MPEG 2
BOARD 7
(1/3)
(Page 34)

F
AV BOARD
CN801A
(Page 40)
0.1

Q5,7,23
BLANKOUT
CONTROL
5 11.3

11.3
0
0.01
2N3904
0.1 0.1 0.01 0.1 0.01 0.1 10.6
0.1 SWITCH
0
1000P
0

0.7
0.1

0.1 0.1 0.01 0.1 0.01 1000P 8.4

MPEG
3 0
BOARD
(1/3) 1000P
(Page 34) 0.1

0.1 0.1

IC8 (1/2)
10
AMP 5
U4 IC8 (1/2) 5
AUDIO DAC BA4558F 5

0.1
0 2.3
9 0 5
10 1.7 0
11 2 0
12
0.1

1000P

5 0
C
5
5 MAIN
BOARD
(2/4)
CN302
0.1 (Page 29)
1000P
IC8(2/2)
BA4558F

IC8 (2/2)
AMP

No mark : DVD STOP

15
16

MPEG
6 BOARD
(2/3)
(Page 35)

HCD-AZ1D
36 36
 HCD-AZ1D
7-16. PRINTED WIRING BOARDS — KEY SECTION — • See page 21 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11

A KEY BOARD HP BOARD • Semiconductor

Location
Ref. No. Location
D601 E-3
VFD651(FLUORESCENT INDICATOR TUBE) D602 G-3
D603 E-7
1 5 10 15 20 25 30 35 40 44 D604 G-7
1 D605 F-4
2 D606 F-5
B D607 F-5
23 22
A 5
PHONES
D608
D651
F-6
G-6
MAIN DISPLAY 33 IC651 12
(STANDBY) D652 B-9
BOARD 34 11 AMP BOARD J D654
D655
F-7
G-4
CN501 CN101
(Page 41) 1
(Page 27) 44 1 IC250 F-10
C 20
21
IC651
IR651
B-6
D-9
E ?/1
E Q601 C-4
Q602 C-4
Q651 G-6
Q652 F-6
Q653 F-8
1 Q654 F-8
D
3

Z IR651
MIC CONTROL BOARD

E K
TAPE
N MAIN BOARD
1 3
DVD
CN202
u VOLUME (Page 27)
MIC LEVEL
TUNING
> . TUNING
F PLAY MODE IC250
E 8 5
x
VOLUME 1 4

E
E MIC

G E
CD SYNC 2 6 PRESET EQ

TUNER/BAND 1 7 PC/TV/AUDIO IN
REC
PAUSE/START
AUDIO IN

PROGRESSIVE
H TAPE
MECHANISM
DECK

L
MAIN BOARD
I 1 3 CN104
(Page 27)

HCD-AZ1D
37 37
HCD-AZ1D
7-17. SCHEMATIC DIAGRAM — KEY SECTION — • See page 47 for IC Block Diagram.

KEY BOARD (FLUORESCENT INDICATOR TUBE)

IR651
REMOTE CONTROL
RECEIVER
4700P
JR651 0
9.5
4.9 Q651, Q652
SOL DRIVER 9.0
9.0

9.5
4.9 0

-29.2

-29.2

-29.2

-32.1

-29.0

-31.5

-29.0

-29.0

-29.0

-24.0

-26.5
0
100

-29.2 -26.5

9.5
-29.2 -29.0
9.4
-29.2 -29.0 7P
9.4
S667 -29.2 -31.5
JR650 9.5
0 -29.2 -29.0 0 Q653, Q654
VOLUME + PC/TV/AUDIO IN
uPD16315GB-3BS MOTOR DRIVER
DISPLAY -29.2 -29.0
B BX TAPE
-29.2 -29.0 MECHANISM
IC651 DECK
-29.2 -29.0
FL DRIVER
-29.2 -26.5
IC B/D
4.9 4.9 JR652 HDPLY
HDPL
0

REC PROGRESSIVE VOLUME -

PAUSE/START

4.9

4.9

1.8

4.9

4.9

4.9

0
50

PLAY TUNING +
> ._ TUNING Z ?/1 4700p
MODE

R607
Q601,Q602 Q601 1K Q602
LED DRIVE 2SC2712GR 2SC2712GR
0.6 0.6 R608
1.5 1.5 1K
R603

R604

R605

R606

R609

R610

R611

R612
470

470

470

470

470

470

470

470

(STNDBY)
0
AMBER

AMBER

AMBER

AMBER

AMBER

AMBER

AMBER

AMBER

D655 D601-D608 D652

D601

D602

D603

D604

D605

D606

D607

D608

JR653
1N4001 SLR-342VCT31 SLR-342VCT31

4V
P203 No mark : FM
HP BOARD C166
21P
L106 CHASSIS

FB

JR102
0
A
J 0.01 JK104 MAIN BOARD (1/4)
CN501
AMP
330 1/2W 330 1/2W (Page 28)
BOARD
JR101
0

CN101
(Page 42) 0.01
330 1/2W 330 1/2W

HCD-AZ1D
38 38
 HCD-AZ1D
7-18. SCHEMATIC DIAGRAM — MIC CONTROL SECTION —

MIC CONTROL BOARD IC250 (1/2) IC250 (2/2)

R258 MIC AMP MIC AMP
4.7K

C268
0.01 JR252 0
IC250(1/2) IC250(2/2)
JK202 C250 BA4558F 9.8
BA4558F
JR251 0.1 8 CN250
R250 R260 4
0 50V 4.8 22K 4.8 3P
4.7K C252 R253 150
C264
3 + 4.8 0.1 5 + R257 1 +10V
MIC 100P
2
1
R254 C253
C265
100P
6
7
4.8
BEAD
2
3
MIC
AGND K
R251 R252 (SMD)
100K 22K 4.8 10K 1000P 4.8 MAIN BOARD(2/4)
C251 VR250 CN202
C256 10K-B
0.1 1000P
R272
(Page 29)
R273 MIC LEVEL C266 R256 150K
1K 47K 0.1

R259 C258 C257 C255

470 C254 R255 1000P
4.7K 0.1 0.1 22K
6.3V

JR250 0
CN603
3P
JK601 L602 1 R

AUDIO IN
2
3
L
AGND
L
L601 MAIN BOARD(4/4)
CN104
(Page 31)
C650
0.1

WP250B

No mark : FM

HCD-AZ1D
39 39
HCD-AZ1D
7-19. PRINTED WIRING BOARD — AV SECTION — • See page 21 for Circuit Boards Location. 7-20. SCHEMATIC DIAGRAM — AV SECTION —
:Uses unleaded solder.

1 2 3

AV BOARD
A F MPEG BOARD
CN2
(Page 33)

JK804A AV BOARD
1
DIGITAL OUT
3
OPTICAL A
1
2
A

B
A
FB A A
A 0
Y

A
V COMPONENT
PB /CB
VIDEO OUT
JK801 A
A 0
A
PR /C R

A
A
15 VIDEO OUT V

16 F A A 0 A

A
MPEG BOARD

A
V

(3/3)

A
CN2
(Page 36) A
A DIGITAL OUT
OPTICAL
WP801A

JK803A
COMPONENT
PB /CB VIDEO OUT

D
PR/CR

HCD-AZ1D
40 40
 HCD-AZ1D
7-21. PRINTED WIRING BOARD — AMP SECTION — • See page 21 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5

[AMP BOARD] • Semiconductor

Location
Ref. No. Location

A J HP BOARD
CW101
E MAIN BOARD
CN105
D101
D102
D103
C-3
B-2
B-2
(Page 37) (Page 27) D104 B-2
D311 C-3
D350 A-1
WP103 D352 B-1
WP102 D353 C-1
D355 C-4
1 E
5 1 3
E IC103 D-2

1
Q101 C-3
Q102 C-3
Q103 B-2
Q104 B-2
I MAIN BOARD
E

E Q105 C-3

B CN103
(Page 27)
Q301
Q303
Q304
B-2
B-2
A-3

E
Q308 B-3
E

7
Q309 C-4
E Q310 C-4
E
)

Q311 D-4
E

10
Q312 D-4
E Q314 C-4
JW(

Q350 B-1
E Q351 B-1
Q352 B-1
Q353 B-1
E E
H MAIN BOARD
CN107
Q354
Q355
B-2
C-1

E
(Page 27)

E
E

1
3
DC FAN

E
1 15

IC103 E

HCD-AZ1D
41 41
HCD-AZ1D
7-22. SCHEMATIC DIAGRAM — AMP SECTION — • See page 47 for IC Block Diagram.

AMP BOARD IC103 070

POWER AMP

IC B/D

-32.8

-31.3
2.6
0

0
31.6

32.9
J
HP BOARD
CW101
(Page 38)

H
MAIN
BOARD (3/4) E
DTC323TK

CN107 MAIN
MUTE

(Page 30)
BOARD(3/4)
0

CN105
0

-4.3V

0
(Page 30)
0.7
0.7

0
DTC323TK

0
MUTE
0

0
-1.0
Q103, Q104
GR
OVER LOAD

-1.0

0
DETECT
GR

6.0
12.3

DC FAN
6

C181A Q350-Q352 1.0

FAN CONT

12.3
0.1

1.0
0.01

12.3
MUTE CONT
10

GR
0

OVER LOAD
1.0

GR
0

DETECT

0
4.9

D351
JW
FAN CURRENT

4.9
DC PROTECT DETECT
4.9 GR 0 0.7
GR

0
I
0

+12V REG GR 0.6

12.3 17.2
MAIN
BOARD (3/4) FAN CURRENT
PROTECT SWITCH

GL
0

CN103 12.3 16.7 DETECT No mark : FM

(Page 30) +12V REG 12.9 SWITCH
GR
0

12.9 13.0 GR DC PROTECT

16.8

DC PROTECT
4.9
SWITCH

0
GR
4.9

17.2
-5.2

0
-5.2

0
0
4.5

HCD-AZ1D
42 42
 HCD-AZ1D
7-23. PRINTED WIRING BOARD — POWER SECTION — • See page 21 for Circuit Boards Location. :Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11

A POWER BOARD • Semiconductor

Location
Ref. No. Location
D901 C-9
AC IN D902 C-9
D903 B-9
PT902 POWER TRANSFORMER(SUB) D904 B-9
B D905 A-8
D906 B-8

NEUTRAL
D907 C-9

LIVE
2 1
C SW901

D 1 PT901 POWER TRANSFORMER(MAIN)

7
SW901
2
VOLTAGE
1
SELECTOR
E 110 120V
3
*
*Not replaceable:
220 240V Built in transformer D
4
MAIN
F BOARD
5 11 CN301
(Page 27)
6

HCD-AZ1D
43 43
HCD-AZ1D
7-24. SCHEMATIC DIAGRAM — POWER SECTION —

POWER BOARD

POWER TRANS FORMER (MAIN) VOLTAGE SELECTOR

JW906

D 4 1
MAIN F901
T1AL/250V JW905 5 2
BOARD(3/4)
CN301 6 3
(Page 30)

JW911
*
FW901 * Not replaceable : Built in transformer

JW907

1
AC IN
V

9 4 2
8
7 3

2
6
5 1

POWER TRANS FORMER (SUB)

HCD-AZ1D
44 44
 HCD-AZ1D

• Waveforms
– MPEG Board – – MAIN Board –

1 U2 <zbm (RFP) 4 U2 <zv, (CVBS/G/Y) 7 IC501 ej (XT2)

2 Vp-p

4.1 Vp-p
1000 mVp-p
H 30.5 µs

200 mV/DIV, 100 ns/DIV 1 V/DIV, 20 µs/DIV 1 V/DIV, 10 µs/DIV

2 U2 <zvv (GCLX) 5 U2 <zbc (C/B/U) 8 IC501 r; (X2)

4.1 Vp-p 1.1 Vp-p 3.6 Vp-p

37 ns H 119 ns
1 V/DIV, 20 ns/DIV 500 mV/DIV, 20 µs/DIV 1 V/DIV, 50 ns/DIV

3 U2 <zb/ (CVBS/C) 6 U2 <zbz (Y/R/V) 9 Q344 (collector)(TAPE REC)

2 Vp-p 10.9 Vp-p

H 0.9 Vp-p 11.8 µs
H
500 mV/DIV, 20 µs/DIV 500 mV/DIV, 20 µs/DIV 20 V/DIV, 5 µs/DIV

45
HCD-AZ1D

• IC Block Diagrams
– MAIN Board –
IC302 BD3881FV

RECO-R

BASS-R
RECO-L

BASS-L
AUX-R

OUT-R
AUX-L

OUT-L
CD-R
TU-R
NF-R

CD-L
TU-L
28 NF-L
27 26 25 24 23 22 21 20 19 18 17 16 15

BASS BASS

VOLUME TREBLE

LOGIC
CONTROL
VOLUME TREBLE

1 2 3 4 5 6 7 8 9 10 11 12 13 14

VDD
NF-L

TA-L

TA-R

NF-R

PBO-R

PBO-L

VOLI-L

VOLI-R

GND

TRE-L

TRE-R

CONT

VEE
IC401 PCM2704 IC402, IC403 BU4066

I/O1 1 14 VDD
XTO 1 28 XTI
(12MHz) OUT/IN IN/OUT
SWA
O/I1 2 13 C1
CK 2 Power Manager 27 SSPND
EEP ROM
Interface PLL(x8)
O/I2 3 SWD 12 C4
DT 3 96MHz 26 TEST0 OUT/IN IN/OUT
Tracker USB Protocol
(SpAct) Controller I/O2 4 11 I/O4
PSEL 4 25 TEST1
IN/OUT OUT/IN
C2 5 SWB 10 O/I4
5 S/PDIF HID
DOUT Analog 24 HID2/MD
Encoder Endpoint
PLL
C3 6 9 O/I3
DGND 6 23 HID1/MC SWC
IN/OUT OUT/IN
ISO-Out VSS 7 8 I/O3
FIFO Endpoint
VDD 7 22 HID0/MS

D- 8 Control 21 HOST
USB Endpoint
XCVR SIE
D+ 9 20 VCCP

VBUS 10 19 PGND

ZGND 11 18 VCOM
DAC
Voltage Regulator
5V to 3.3V

AGNDL 12 17 AGNDR

VCCL 13 16 VCCR

VOUTL 14 15 VOUTR

46
 HCD-AZ1D

– KEY Board –

IC651 uPD16315GB-3BS

SEG24/GRID5

SEG23/GRID6

SEG22/GRID7

SEG21/GRID8

SEG20/GRID9
GRID1

GRID2

GRID3

GRID4
VDD
VSS
44 43 42 41 40 39 38 37 36 35 34

Grid driver
Multiplexed driver
33 SEG19/GRID10

Command decoder
LED1 1
32 SEG18/GRID11

LED2 2
4-bit latch

12-bit shift register

LED3 3 Display memory
24 bits x 12 words 31 SEG17/GRID12

LED4 4

Data selector
OSC 5 OSC 30 VEE
Timing generator
key scan
24-bit output latch

DOUT 6

29 SEG16/KS16
DIN 7 Key data memory
Serial (2 x 16 bits) 28 SEG15/KS15
interface
CLK 8 27 SEG14/KS14

STB 9 26 SEG13/KS13

25 SEG12/KS12

segment driver 24 SEG11/KS11

KEY1 10
KEY2 11 23 SEG10/KS10

12 13 14 15 16 17 18 19 20 21 22
VSS

VDD

SEG1/KS1

SEG2/KS2

SEG3/KS3

SEG4/KS4

SEG5/KS5

SEG6/KS6

SEG7/KS7

SEG8/KS8

SEG9/KS9

– AMP Board –

IC103 STK433-070

Pre Driver Pre Driver

CH1 CH2

Bias Circuit

SUB
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
CH2_IN
CH2_NF

ST_BY

CH1_NF
CH1_IN
GND
SUB
+PRE

CH2_OUT2
CH2_OUT1
CH1_OUT2
CH1_OUT1

+VCC
-VCC
-PRE

47
HCD-AZ1D

• IC Pin Function Description

MAIN BOARD IC501 uPD780078 (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Description
1 MUTE1 O Muting signal output to the VIDEO AMP (not used)
2 MUTE2 O Muting signal output to the VIDEO AMP (not used)
3 RPHD O REC/PLAY control signal output
4 BIAS O BIAS ON/OFF control signal output
5 TSOL O Tape solenoid control signal output
6 TMOT O Tape motor control signal output
7 TCNT O Tape control signal output
8 VIDEO SW I RGB/COMPONENT select SW signal input (not used)
9 GND — Ground terminal
10 VDD — Power supply terminal (+5V)
11 STE I Stereo signal input
12 TUCE O Chip enable signal output to the tuner
13 VIDS O INT/PRO signal output (not used)
14 TOP I DVD/CD tray open SW signal input
15 VEDA O Chip select output to the FL driver
16 VFCK O Clock output to the FL driver
17 VFSTB O Data output to the FL driver
18 TUDI O Data output to the tuner
19 TUDO I Data input from the tuner
20 TUCK O Clock output to the tuner
21 RDDA O Strobe signal output to the tuner (not used)
22 VUP I Volume up input (not used)
23 FPON O FL power supply control signal output
24 VDD1 — Power supply terminal (+5V)
25 GND — Ground terminal
26 KEY1 I Function key input
27 KEY2 I Function key input
28 KEY3 I Function key input
29 SFTY I AC cut detect signal input
30 HDPN I Tape SW (PACK, HDPLY) signal input
31 REPT I Tape SW (RECF, RECR) signal input
32 VER I Destination version setting
33 VDWN I Volume down input (not used)
34 AVR I Reference voltage terminal
35 TCL I DVD/CD tray close SW signal input
36 RST I System reset signal input
37 XT2 I Subclock input (36.768KHz)
38 XT1 O Subclock output (36.768KHz)
39 IC — Not used
40 X2 I Main system clock input (8.38MHz)
41 X1 O Main system clock output (8.38MHz)
42 GND — Ground terminal
43 U-SENS O USB SENS signal output
44 INH I Power down detect signal input
45 REM I SIRES signal input from the remote control receiver
46 RDCK O RDCK signal output to the tuner (not used)
47 MRST O MPEG reset signal output

48
 HCD-AZ1D

Pin No. Pin Name I/O Description

48 DSDA O DAC encoder data signal output
49 DSSTB O DAC encoder chip enable signal output
50 DSCK O DAC encoder clock signal output
51 XTO — Not used
52 STRB O Strobe data out to the sound processor
53 SDAT/ROMDA O Data output to the EPROM
54 SCK/ROMCK O Clock output to the EPROM
55 OPN O Loading motor FWD control signal output
56 CLS O Loading motor REV control signal output
57 AUXTVS O Clock output to the quad analog switch
58 USBPS O Data output to the quad analog switch
59 AMUT O Audio line muting signal output
60 LED O LED control signal output
61 TUON O Tuner power supply control signal output
62 CD ON O CD power supply control signal output
63 RLY O Relay control signal output
64 PCON O Power supply control signal output

49
HCD-AZ1D

MPEG BOARD U2 ZR36862 (RF AMP, FOCUS/TRACKING ERROR AMP, VIDEO DAC ENCODER)
Pin No. Pin Name I/O Description
1 SSCRXD/IO17 I Chip enable signal input from the system controller
2 MCS1/IO18 — Not used
3 VDDP — Power supply terminal (+3.3V)
4 to 7 MAD16 to 13 O Flash memory address bus
8 MAD12/PLLCFGA O Flash memory address bus
9 MDA15 I/O Flash memory data bus
10 MAD11/PLLCFGP O Flash memory address bus
11 MDA7 I/O Flash memory data bus
12 GND P — Ground terminal
13 MAD10 O Flash memory address bus
14 MDA14 I/O Flash memory data bus
15 MAD9 O Flash memory address bus
16 MDA6 I/O Flash memory data bus
17 MAD8 O Flash memory address bus
18 MDA13 I/O Flash memory data bus
19 MDA5 I/O Flash memory data bus
20 MAD20/IO19/CS2 O Flash memory address bus (not used)
21 VDDP — Power supply terminal (+3.3V)
22 MDA12 I/O Flash memory data bus
23 MWR# O Flash memory write enable signal output
24 MDA4 I/O Flash memory data bus
25 VDDC — Power supply terminal (+1.8V)
26 MDA11 I/O Flash memory data bus
27 MDA3 I/O Flash memory data bus
28 MAD19/PLLSEL O Flash memory address bus
29 GNDC — Ground terminal
30 MDA10 I/O Flash memory data bus
31 MAD18 O Flash memory address bus
32 GNDP — Ground terminal
33 MDA2 I/O Flash memory data bus
34 MAD17 O Flash memory address bus
35 MDA9 I/O Flash memory data bus
36 MAD7 O Flash memory address bus
37 MDA1 I/O Flash memory data bus
38 MAD6 O Flash memory address bus
39 MDA8 I/O Flash memory data bus
40 MAD5 O Flash memory address bus
41 VDDP — Power supply terminal (+3.3V)
42 MDA0 I/O Flash memory data bus
43 MAD4 O Flash memory address bus
44 MRD# O Flash column high address strobe signal output
45 MAD3 O Flash memory address bus
46 MAD2 O Flash memory address bus
47 MCS#0 O Flash memory output enable signal output
48 MAD1/BOOTSEL2 O Flash memory address bus
49 MAD0/BOOTSEL1 O Flash memory address bus
50 GNDP — Ground terminal
51 VDD-IP — Power supply terminal (+3.3V)

50
 HCD-AZ1D

Pin No. Pin Name I/O Description

52 VDDP — Power supply terminal (+3.3V)
53 to 57 RADD2 to 6 O Address bus to the D-RAM
58 VDDP — Power supply terminal (+3.3V)
59 RADD1 O Address bus to the D-RAM
60 RADD7 O Address bus to the D-RAM
61 RADD0 O Address bus to the D-RAM
62 GNDP — Ground terminal
63 RADD8 O Address bus to the D-RAM
64 VDDC — Power supply terminal (+1.8V)
65 RADD10 O Address bus to the D-RAM
66 GNDC — Ground terminal
67 RADD9 O Address bus to the D-RAM
68 VDDP — Power supply terminal (+3.3V)
69 RADD11 O Address bus to the D-RAM (not used)
70 RCS#0/RBA1 O Chip select signal output to the D-RAM (IC4)
71 RBA0 O Address bus to the D-RAM
72 GNDP — Ground terminal
73 RCS#1 O Chip select signal output to the D-RAM (IC5)
74 RRAS# O D-RAM Low address strobe signal output
75 RCAS# O D-RAM column address strobe signal output
76 VDDP — Power supply terminal (+3.3V)
77 RWE# O D-RAM write enable signal output
78 RDQM# O D-RAM data signal output
79 GNDPCLK — Ground terminal
80 PCLK O D-RAM clock output
81 VDDPCLK — Power supply terminal (+3.3V)
82 RDAT8 I/O Data bus to the D-RAM
83 GNDP — Ground terminal
84 RDAT7 I/O Data bus to the D-RAM
85 RDAT9 I/O Data bus to the D-RAM
86 RDAT6 I/O Data bus to the D-RAM
87 VDDP — Power supply terminal (+3.3V)
88 RDAT10 I/O Data bus to the D-RAM
89 RDAT5 I/O Data bus to the D-RAM
90 RDAT11 I/O Data bus to the D-RAM
91 GNDP — Ground terminal
92 RDAT4 I/O Data bus to the D-RAM
93 VDDC — Power supply terminal (+1.8V)
94 RDAT12 I/O Data bus to the D-RAM
95 GNDC — Ground terminal
96 RDAT3 I/O Data bus to the D-RAM
97 VDDP — Power supply terminal (+3.3V)
98 RDAT13 I/O Data bus to the D-RAM
99 RDAT2 I/O Data bus to the D-RAM
100 RDAT14 I/O Data bus to the D-RAM
101 GNDP — Ground terminal
102 RDAT1 I/O Data bus to the D-RAM
103 RDAT15 I/O Data bus to the D-RAM
104 RDAT0 I/O Data bus to the D-RAM

51
HCD-AZ1D

Pin No. Pin Name I/O Description

105 VDDP — Power supply terminal (+3.3V)
106 CPUNM/IO20 — Not used
107 GNDP — Ground terminal
108 ICIO0 — Not used
109 ICIO0 — Not used
110 SPDIF O SPDIF (DVD/CD) change signal output
111 IO21/AOUT2 — Not used
112 IO22/AOUT1 — Not used
113 AOUTO O Signal output to the audio DAC
114 GPAIO — Not used
115 ALRCLK O LRCK signal output to the audio DAC
116 ABCLK O BCK signal output to the audio DAC
117 GNDP-A2 — Ground terminal
118 AMCLK I AMCLK signal input from the AV decoder
119 VDDP-A2 — Power supply terminal (+3.3V)
120 IO23/AIN — Not used
121 IO24/VSYNC — Not used
122 IO25/HSYNC — Not used
123 GNDP — Ground terminal
124 ICI01/VCLK*2 — Not used
125 VDDP — Power supply terminal (+3.3V)
126 IO26/VID7 — Not used
127 IC102/VID6 — Not used
128 IOI01/VID5 — Not used
129 IO27/VID4 — Not used
130 GNDC — Ground terminal
131 VDDC — Power supply terminal (+1.8V)
132 IO28/VID3 — Not used
133 IO29/VID2 — Not used
134 IO30/VID1 — Not used
135 IC103/VIDO O SDA signal output to the EEPROM
136 IO31 O SCL signal output to the EEPROM
137 IDI02 I COMPONENT/RGB-SW control signal input
138 VDD — Power supply terminal (+3.3V)
139 GNDP — Ground terminal
140 GNDA — Ground terminal
141 RESET# I Reset signal input from the system controller
142 VDDA — Power supply terminal (+1.8V)
143 XO O System clock output (27MHz)
144 GCLK I System clock input (27MHz)
145 GNDDACD — Ground terminal
146 GNDDACD — Ground terminal
147 Y/C — Not used
148 CVBS/C/Y O Video signal output
149 VDDDAC — VDDDAC power supply terminal (+3.3V)
150 CVBC/C O Video signal output
151 Y/R/V O Video signal output
152 VDDDAC — VDDDAC power supply terminal (+3.3V)
153 C/B/V O Video signal output

52
 HCD-AZ1D

Pin No. Pin Name I/O Description

154 RSET I Connected to ground
155 GNDDACP — Ground terminal
156 GNDDACBS2 — Ground terminal
157 RF P I Main-beam RF signal input
158 RF N I Not used
159 G I DC coupled main-beam RF signal input G (not used)
160 A I DC coupled main-beam RF signal input A
161 AVDD1 — Power supply terminal (+3.3V)
162 B I DC coupled main-beam RF signal input B
163 SVDD — Power supply terminal (+3.3V)
164 AVDD — Power supply terminal (+3.3V)
165 C I DC coupled main-beam RF signal input C
166 H I DC coupled main-beam RF signal input H (not used)
167 D I DC coupled main-beam RF signal input D
168 J — Not used
169 AGND — Ground terminal
170 E I DC coupled main-beam RF signal input E
171 K — Not used
172 F I DC coupled main-beam RF signal input F
173 VC I Control signal input from Optical pick-up
174 VBCAP — Connected to +3.3V
175 RESOUT I Connected to ground
176 CD_MD O Volume control signal output to Optical pick-up
177 DVD_MD O Volume control signal output to Optical pick-up
178 CD_LD O Laser drive output
179 DVD_LD O Laser drive output
180 AGND — Ground terminal
181 AGND1 — Ground terminal
182 VDDC — Power supply terminal (+1.8V)
183 I032 O Motor Drive AMP signal output
184 GNDC — Ground terminal
185 ICI04 I SW (close) signal input
186 ICI05 I SW (open) signal input
187 VDDP — Power supply terminal (+3.3V)
188 IDI03 O Laser select drive output
189 GNDP — Ground terminal
190 ICI06 — Not used
191 ICI07 — Not used
192 VDD-IP — Power supply terminal (+3.3V)
193 IDI06/SLED — Not used
194 IDI07/SPINDLE — Not used
195 I043/PWMCO2 O Motor Drive AMP signal output
196 I044/PWMCO3 O Motor Drive AMP signal output (not used)
197 GNDPWM — Ground terminal
198 I045/PWMCO4 O Motor Drive AMP signal output
199 VDDPWM — Power supply terminal (+3.3V)
200 I046/PWMCO5 I HOME SW signal input
201 IDI04/PWMCO6 O Motor Drive AMP signal output
202 I04/PWMCO0 O Motor Drive AMP signal output

53
HCD-AZ1D

Pin No. Pin Name I/O Description

203 IO35/DUPRD0 O Latch enable signal output to the audio DAC (not used)
204 IO36/DUPTD0 O Line3 control signal output
205 IO37/DUPRD1 O Line3 control signal output
206 IO38/DUPTD1 O Video signal output terminal (D1/S) change signal output
207 IO47/SSCCLK I Clock signal input from the system controller
208 IO16/SSCTXD I Data signal input from the system controller
209 to 257 HOLE1 to 49 — Connected to ground

54
 HCD-AZ1D
SECTION 8
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they • The mechanical parts with no reference
The components identified by mark 0 or
may have some difference from the original number in the exploded views are not supplied.
dotted line with mark 0 are critical for safety.
one.
Replace only with part number specified.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.

8-1. OVERALL SECTION not

supplied
3

not not
not supplied supplied
supplied not
supplied not
not 2 supplied
supplied not
supplied not
a supplied
not
supplied
not not
supplied not supplied
supplied DVD mechanism
deck section
not
supplied
not not
not supplied supplied
not supplied
supplied not
not supplied
supplied not
not supplied
supplied
a not
supplied

not 4
front panel section supplied not
supplied

not
supplied
not
supplied

not
supplied

not
supplied chassis section
1
not
supplied

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 9-885-100-50 PANEL TRAY DVD 3 9-885-105-69 MPEG BOARD, COMPLETE
2 9-885-100-24 TOP COVER 4 9-885-083-69 FAN, DC

55
HCD-AZ1D

8-2. FRONT PANEL SECTION not

supplied
not
72 supplied
not
supplied

62
61
including Ref. No. 72
HP board
63
not 80
supplied 66
60 not
supplied 64

59
71
65
80
70
67 73
58 68 69

not 74
supplied

57 not not
supplied supplied
78 75
56 77
not
55 supplied

not
79 supplied

not
57 supplied

54 53 not
supplied
not not
supplied supplied 76 not
not supplied
supplied

52
51 not
supplied
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 9-885-100-67 WINDOW CASS 66 9-885-100-53 BASE KEY LEFT
52 9-885-100-68 PANEL CASS 67 9-885-100-61 KEY SKIP LEFT
53 4-238-631-01 TAPE SPRING 68 9-885-100-62 KEY SKIP RIGHT
54 9-885-100-64 RING VOLLUME 69 9-885-100-55 LENS TUNER
55 9-885-100-65 LENS VOLUME 70 9-885-100-56 LENS DVD

56 9-885-100-63 KEY VOLUME 71 9-885-100-54 BASE KEY RIGHT

57 9-885-100-66 LENS ORNAMENT 72 9-885-105-25 KEY BOARD, COMPLETE (including HP BOARD)
58 9-885-100-49 WINDOW DISPLAY 73 9-885-107-27 WIRE (FLAT TYPE)(21 CORE)
59 9-885-100-48 CABI FRONT 74 9-885-100-52 KEY FUNCTION RIGHT
60 9-885-100-69 LENS SENSOR 75 9-885-101-01 FFC CABLE 7PIN PITCH=1.25

61 9-885-100-60 LENS POWER 76 1-796-352-81 DECK, MECHANICAL (CMAL5Z220C)

62 9-885-100-59 CAP KEY POWER 77 4-231-825-01 CAM (B), HEART
63 9-885-100-51 KEY FUNCTION LEFT 78 4-231-841-01 SPRING (HEART CAM-B)
64 9-885-100-58 LENS TAPE 79 4-242-318-01 OIL-DAMPER (70N)
65 9-885-100-57 LENS TV 80 9-885-100-71 LENS LED
Note: If the wire (flat type) was replaced, fold it some as the
wire (flat type) before replacement.

56
 HCD-AZ1D

8-3. CHASSIS SECTION

not
supplied
101 not not
supplied supplied
not
supplied not
not supplied
supplied
103

not not
supplied supplied

F901 PT901 a not

102 supplied not
not supplied
not
supplied supplied not
not supplied
supplied not
not supplied
supplied

108
not not
supplied not supplied
supplied
a 105
104
106
not
supplied
not
supplied not
supplied
not
supplied 107

not not
supplied not supplied not
supplied supplied
not
supplied

not
supplied
not
supplied

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 9-885-105-27 POWER BOARD, COMPLETE 106 9-885-101-07 FF-CABLE 12P P=1.25MM L=1
0 102 1-769-744-11 CORD, POWER 107 9-885-105-26 MAIN BOARD, COMPLETE
103 9-885-101-06 FF-CABLE 16P P=1.25MM L=1 108 9-885-100-75 PANEL REAR
104 1-693-702-11 TUNER (FM/AM) (TM10SE) 0 F901 1-532-463-31 FUSE (T1AL/250V)
105 9-885-101-08 FF-CABLE 9PINS P=1.25MM R 0 PT901 9-885-105-28 POWER TRANSFORMER

Note: If the wire (flat type) was replaced, fold it some as the
wire (flat type) before replacement.

57
HCD-AZ1D

8-4. DVD MECHANISM DECK SECTION

not
supplied

152
not not
supplied supplied
153

not not
supplied supplied
not
supplied
not
supplied

not
supplied

not
supplied

151

not
supplied

Ref. No. Part No. Description Remark

151 9-885-101-04 MECHANISM LOADER WXD
0 152 9-885-101-00 OPTICAL PICK-UP DM3451-A (SF-HD65F)
153 9-885-101-02 FF-CABLE 24PINS P=0.5MM

Note: If the wire (flat type) was replaced, fold it some as the
wire (flat type) before replacement.

58
 HCD-AZ1D
SECTION 9
AMP AV KEY HP MAIN
ELECTRICAL PARTS LIST
MIC CONTROL MPEG
NOTE:
• Due to standardization, replacements in the • COILS
When indicating parts by reference number,
parts list may be different from the parts uH: µH
please include the board name.
specified in the diagrams or the components • RESISTORS
used on the set. All resistors are in ohms.
The components identified by mark 0 or
• -XX and -X mean standardized parts, so they METAL: Metal-film resistor.
dotted line with mark 0 are critical for safety.
may have some difference from the original METAL OXIDE: Metal oxide-film resistor.
Replace only with part number specified.
one. F: nonflammable
• Items marked “*” are not stocked since they • SEMICONDUCTORS
are seldom required for routine service. In each case, u: µ, for example:
Some delay should be anticipated when uA. . : µA. . , uPA. . , µPA. . ,
ordering these items. uPB. . : µPB. . , uPC. . , µPC. . ,
• CAPACITORS uPD. . : µPD. .
uF: µF

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
AMP BOARD IC402 9-885-105-31 IC BU4066
********** IC403 9-885-105-31 IC BU4066

< IC > IC502 9-885-100-91 IC BD4736G

IC503 9-885-100-90 IC AT24C0
IC103 6-705-621-01 IC STK433-070
************************************************************* < TERMINAL BOARD >

AV BOARD JK102 9-885-104-49 TERMINAL BOARD (SPEAKER)

*********
< JACK >
*************************************************************
JK201 9-885-059-87 JACK, PIN 4P (TV)
9-885-105-25 KEY BOARD, COMPLETE (including HP BOARD)
******************** < TRANSFORMER >

< DIODE > T301 9-885-059-58 OSCILLATION, BIAS TRANSFORMER

D601 8-719-059-98 DIODE SLR-342VC3F < VIBRATOR >

D602 8-719-059-98 DIODE SLR-342VC3F
D603 8-719-059-98 DIODE SLR-342VC3F X501 9-885-059-48 VIBRATOR, CRYSTAL (32.768kHz)
D604 8-719-059-98 DIODE SLR-342VC3F X502 9-885-059-52 OSCILLATOR, CERAMIC (8.38MHz)
D605 8-719-059-98 DIODE SLR-342VC3F *************************************************************

D606 8-719-059-98 DIODE SLR-342VC3F MIC CONTROL BOARD

D607 8-719-059-98 DIODE SLR-342VC3F ******************
D608 8-719-059-98 DIODE SLR-342VC3F
D652 8-719-059-98 DIODE SLR-342VC3F (STANDBY) < JACK >

< IC > JK202 9-885-077-09 HEADPHONE JACK EJ-3507P-2 (MIC)

JK601 9-885-077-09 HEADPHONE JACK EJ-3507P-2 (AUDIO IN)
IC651 8-759-643-83 IC uPD16315GB-3BS *************************************************************
IR651 6-701-681-01 IC RPM7140-V4
9-885-105-69 MPEG BOARD, COMPLETE
< FLUORESCENT INDICATOR TUBE > *********************

VFD651 1-519-761-31 INDICATOR TUBE, FLUORESCENT < IC >

HP BOARD IC4 9-885-100-98 IC K4S161622H

********* IC5 9-885-100-98 IC K4S161622H
IC7 9-885-100-95 IC AM5888S
< JACK > IC8 8-759-909-71 IC BA4558F
IC14 9-885-100-90 IC AT24C0
JK104 9-885-077-09 HEADPHONE JACK EJ-3507P-2 (PHONES)
************************************************************* U2 9-885-100-96 IC ZR36862 TQFP-208

9-885-105-26 MAIN BOARD, COMPLETE < VIBRATOR >

*********************
Y1 9-885-059-78 VIBRATOR, CRYSTAL (27MHz)
< IC > *************************************************************

IC301 9-885-059-44 IC AP1501

IC302 6-702-895-01 IC BD3881FV
IC401 9-885-105-30 IC PCM2704

59
HCD-AZ1D
POWER

Ref. No. Part No. Description Remark

9-885-105-27 POWER BOARD, COMPLETE
***********************

< TRANSFORMER >

0 PT902 9-885-059-89 TRANSFORMER, POWER

< RELAY >

0 RY901 9-885-059-96 RELAY, POWER

<SWITCH>

0 SW901 1-786-404-11 SELECTOR, VOLTAGE (SWS-2201)

(VOLTAGE SELECTOR)
*************************************************************

MISCELLANEOUS
**************

4 9-885-083-69 FAN, DC
73 9-885-107-27 WIRE (FLAT TYPE)(21 CORE)
75 9-885-101-01 FFC CABLE 7PIN PITCH=1.25
76 1-796-352-81 DECK, MECHANICAL (CMAL5Z220C)
0 102 1-769-744-11 CORD, POWER

103 9-885-101-06 FF-CABLE 16P P=1.25MM L=1

104 1-693-702-11 TUNER (FM/AM) (TM10SE)
105 9-885-101-08 FF-CABLE 9PINS P=1.25MM R
106 9-885-101-07 FF-CABLE 12P P=1.25MM L=1
151 9-885-101-04 MECHANISM LOADER WXD

0 152 9-885-101-00 OPTICAL PICK-UP DM3451-A (SF-HD65F)

153 9-885-101-02 FF-CABLE 24PINS P=0.5MM
0 F901 1-532-463-31 FUSE (T1AL/250V)
0 PT901 9-885-105-28 POWER TRANSFORMER

60
 HCD-AZ1D

MEMO

61
HCD-AZ1D

REVISION HISTORY

Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.

Ver. Date Description of Revision

1.0 2006.05 New