Als Series: Alcplus2 Idu Asn Odu
Als Series: Alcplus2 Idu Asn Odu
Als Series: Alcplus2 Idu Asn Odu
ALCplus2 IDU
ASN ODU
IP/ SDH/ SPDH
Dual Native TDM/IP Microwave Radio
GENERAL INTRODUCTION ON ALS SERIES
The ALS Series provides scalable data rates from 4 to 500 Mbit/s per
radio module with a single platform across the full range of licensed Figure - ALS Series MW Radio
frequency bands.
A single shelf can manage up to 1 Gbit/s with 1RU version. A unique distributed processing architecture allows
expanding the node capacity up to 8xGbit/s.
A wide range of tributary interfaces and system configurations offer maximum versatility in system engineering
and network planning. Ethernet traffic is handled by a powerful integrated switch able to manage VLANs, QoS
and ToS.
Modularity options, commonalities, and extensive software management capabilities result in cost-effectiveness
and scalability, yielding a product that will easily fulfill any future requirement.
Full SW licensing approach allows very smooth migration from pure TDM to IP networks, with very low initial
CAPEX.
The ALS equipment is managed by an SNMP agent using communication ports that are able to connect to IP and
OSI DCNs. This greatly simplify integration efforts in existing NMS networks.
Several IDU models are available ranging from single board solutions to nodal implementations in which high
capacities and complex protection schemes are required:
Product Range
The ALS Series is available in all frequency bands from 6 GHz (6L and 6U) to 42 GHz (4GHz is available for
PDH/ETH application), unduplicated or duplicated configuration and with radio capacity from 4 to 400 Mbit/s
per radio module with mixed TDM and ETH interfaces.
The modulation scheme is software programmable from 4QAM to 256QAM for ALplus2 IDU, with full featured
ACM. ALS exploits an innovative dual native radio engine capable of transmitting both native TDM (4xE1 to
4xSTM-1) and native ETH (up to 400 Mbit/s) .
Main Features
Scalable capacity, integrated XPIC functionality, high performance and reliability, ease of installation, common
NMS platform and cost effectiveness make the ALS Series the proper network solution for a wide set of network
applications.
Both electrical and optical interfaces are available on the same terminal radio equipment.
Adaptive Code and Modulation allows the automatic selection of the optimum modulation scheme according to
current radio link propagation conditions and on received signal’s quality can be software enabled; on the basis of
received signal quality calculations, the ALS Series can increase the system gain when needed, thus forwarding
the high priority traffic in bad propagation conditions too. In addition, the introduction of heavily coded
modulation schemes allows the system to perform in challenging environmental conditions.
With ACM and traffic classification, each traffic class is assigned with its minimum required QoS, allowing easy
overbooking of existing radio link, without any impact on antenna sizes and infrastructure hardware.
ALCplus2 IDU with its state-of-art high speed ACM can compensate fading speed up to 40dB/s; this allows easy
network planning in very bad environment condition characterized of deep fading conditions and with fast fading
phenomena (e.g multiple path interference for lower frequency bands)
In addition, user configurable ACM profiles allow per-link optimization with the possibility to full customize
adaptive modulation behavior.
All SIAE MICROELETTRONICA NMS solutions are based on standard protocols. SNMP Protocol is used for TMN
connections with standard communication protocol stacks and industry-standard interfaces allowing equipment
connection to any IP or OSI-based DCN.
Universal ASN ODU supports all modulation schemes (4/8/16/32/64/128/256QAM) and all capacities
from 8 Mbit/s to 400 Mbit/s. AS ODU doesn’t require any hardware change if configured for
frequency reuse (independence from XPIC functionality), moreover It is compatible with ALL IDU
models. This model provides up to 20 dB ATPC.
These modulation independent ODUs allow an “install-and-forget” approach for simple station upgrading.
ASN ODU
Figure - ASN ODU with integral antenna in 1+0 and 1+1 configuration
Figure - Universal ODU with not integrated antenna solution in 1+0 and 1+1 configurations
Fixed output power attenuation mode (ATPC disabled); the output power can be reduced up to 20dB in
1dB steps (40dB in Advanced AS ODU).
ATPC mode: the ATPC algorithm adjusts the output power attenuation in order to reach a predefined Rx
level at the remote terminal.
STM-1 interfaces are available also for SPDH configurations reducing installation cable count.
ALCplus2 is available with a wide range of interface options, from 4xFE/GE Sync/Async to 4xFE/GE Sync/Async +
(2+32)xE1 + 2xSTM-1 (MSP).
1 2 3 4 6 7
8 1 9 10
Figure 2 - ALCplus2 IDU - 34xE1 + 4xGE + 2xSTM-1
IDU options
o 4xFE/GE Sync/Async + 2xE1 + 32xE1 + 2xSTM-1(1+1 MSP)
Protection Schemes
1+1 hot stand-by, frequency and/or space diversity
Adaptive Code Modulation (ACM)
This procedure has a drawback: when propagation conditions are favourable the system could support higher
data traffic but it cannot increase its throughput unless it changes its modulation scheme.
In order to trigger a modulation change some switching criteria must be implemented. SIAE MICROELETTRONICA
solutions are based on MSE measurements that allow the system to react to any source of degradation, well
before errors are detected by the FEC. It involves one direction at a time and the process is completely jitter and
error free for surviving traffic.
SIAE MICROELETTRONICA implements MSE based Adaptive Modulation in all channel bandwidths. 8 ACM profiles
are provided, each one can be selected by SW in order to build a user configured Adaptive Modulation Profile.
ALCplus2
In the following table is shown indicative throughput calculated with 64 bytes packet traffic.
Packet IDU – Typical Ethernet throughput for 64 bytes frame (including Header
Channel Optimisation) Mbit/s
Width
4QAM
4QAM 8 QAM 16QAM 32QAM 64QAM 128QAM 256QAM
“Strong”
7 MHz 10 12 1 18 25 30 38 s 42 50
14 MHz 20 25 37 50 60 75 85 100
TECHNICAL CHARACTERISTICS
Physical Dimensions of system components
1
This is the default configuration. Maximum modulation upgrading and channel bandwidth expansion can be
achieved through simple license file download.
System Version Width (mm) Height (mm) Depth (mm)
Weight
System Version Weight(Kg)
Power supply
ODU Range
-40.8 -57.6 Vdc
According to ETSI EN300132-2
Environmental conditions
6L/6U 10/11
7/8 GHz 13 GHz 15 GHz 18 GHz 23 GHz 25 GHz 28 GHz 32 GHz 38 GHz 42 GHz
GHz GHz
4 QAM +29 +29 +28 +28 +28 +23 +23 +22 +21 +20 +19 +17
8 QAM +29 +29 +28 +28 +28 +23 +23 +22 +21 +20 +19 +17
16 QAM +26 +26 +25 +25 +25 +21 +21 +20 +19 +18 +17 +15
32 QAM +26 +26 +25 +25 +25 +21 +21 +20 +19 +18 +17 +15
64 QAM +25 +25 +24 +24 +24 +19 +19 +18 +17 +16 +15 +13
128 QAM +25 +25 +24 +24 +24 +19 +19 +18 +17 +16 +15 +13
256 QAM +24 +24 +23 +23 +23 +18 +18 +17 +16 +15 +14 +12
Throughput ALCplus2
Throughput is defined according to paragraph 26.1 of RFC2544.
Throughput is configuration and capacity dependent, so in the following tables a different throughput parameter
will be specified for each configuration.
Typical Radio Throughput at point X/X' for Ethernet 64 bytes input traffic [Mbit/s]
Channel width 4QAM 4QAM 8 QAM 16QAM 32QAM 64QAM 128QAM 256QAM
Strong
7 MHz 10 12 17 24 29 36 41 48
14 MHz 20 24 34 48 60 71 83 98
28 MHz 41 49 73 97 121 145 169 198
56 MHz 82 96 143 193 235 280 333 396
1
Typical values
Typical Radio Throughput at point X/X' for Ethernet 1024 bytes input traffic [Mbit/s]
Channel width 4QAM 4QAM 8 QAM 16QAM 32QAM 64QAM 128QAM 256QAM
Strong
7 MHz 9 11 15 21 25 31 35 41
14 MHz 18 21 29 41 52 62 72 84
28 MHz 36 42 63 83 104 125 145 171
56 MHz 71 83 124 166 203 241 288 343
Typical Radio Throughput at point X/X' for Ethernet 1518 bytes input traffic [Mbit/s]
Channel width 4QAM 4QAM 8 QAM 16QAM 32QAM 64QAM 128QAM 256QAM
Strong
7 MHz 9 11 15 21 25 31 35 41
14 MHz 17 21 29 41 51 61 71 84
28 MHz 36 42 62 83 104 124 145 170
56 MHz 71 82 123 165 202 240 287 342
SIAE Microelettronica do Brasil Ltda. – Alameda Vicente Pinzon, 173 – Vila Olimpia – CEP 04547-130