Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Safety Data Sheet: SECTION 1: Identification of The Substance/mixture and of The Company/undertaking

Download as pdf or txt
Download as pdf or txt
You are on page 1of 16

Conforms to Regulation (EC) No.

1907/2006 (REACH), Annex II


MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SAFETY DATA SHEET

SECTION 1: Identification of the substance/mixture and of the company/undertaking


1.1 Product identifier
Product name : MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
Product code : M262A

1.2 Relevant identified uses of the substance or mixture and uses advised against
Material uses : Paint or paint related material.
: Industrial use only.

1.3 Details of the supplier of the safety data


sheet
Sherwin-Williams Protective & Marine
Tower Works
Kestor Street
Bolton
BL2 2AL
United Kingdom
+44 (0) 1204 521771

e-mail address of person : hse.pm.emea@sherwin.com


responsible for this SDS

1.4 Emergency telephone number


National advisory body/Poison Centre
Telephone number : 0844 892 0111
Supplier
Telephone number : +(44)-870-8200 418
Hours of operation : Emergency contact available 24 hours a day

SECTION 2: Hazards identification


2.1 Classification of the substance or mixture
Product definition : Mixture
Classification according to Regulation (EC) No. 1272/2008 [CLP/GHS]
Flam. Liq. 3, H226
Skin Irrit. 2, H315
Eye Dam. 1, H318
Skin Sens. 1, H317
STOT SE 3, H335
STOT RE 2, H373
Asp. Tox. 1, H304
Aquatic Chronic 3, H412
The product is classified as hazardous according to Regulation (EC) 1272/2008 as amended.
See Section 16 for the full text of the H statements declared above.
See Section 11 for more detailed information on health effects and symptoms.

2.2 Label elements

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 1/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 2: Hazards identification


Hazard pictograms :

Signal word : Danger


Hazard statements : Flammable liquid and vapour.
Causes serious eye damage.
Causes skin irritation.
May cause an allergic skin reaction.
May be fatal if swallowed and enters airways.
May cause respiratory irritation.
May cause damage to organs through prolonged or repeated exposure.
Harmful to aquatic life with long lasting effects.
Precautionary statements
Prevention : Wear protective gloves. Wear eye or face protection. Keep away from heat, hot
surfaces, sparks, open flames and other ignition sources. No smoking. Use
explosion-proof electrical, ventilating, lighting and all material-handling equipment.
Avoid release to the environment. Do not breathe vapour.
Response : IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF
SWALLOWED: Immediately call a POISON CENTER or physician. Do NOT
induce vomiting. IF ON SKIN (or hair): Take off immediately all contaminated
clothing. Rinse skin with water or shower. IF IN EYES: Immediately call a POISON
CENTER or physician.
Storage : Keep cool.
Disposal : Dispose of contents and container in accordance with all local, regional, national
and international regulations.
Hazardous ingredients : Polyamide
Xylene
Triethylene Tetramine
Supplemental label : FOR INDUSTRIAL USE ONLY
elements
Annex XVII - Restrictions : Not applicable.
on the manufacture,
placing on the market and
use of certain dangerous
substances, mixtures and
articles
Special packaging requirements
Not applicable.

2.3 Other hazards


Other hazards which do : None known.
not result in classification

SECTION 3: Composition/information on ingredients


3.2 Mixture :

Classification
Product/ingredient Identifiers % Regulation (EC) No. 1272/2008 [CLP] Type
name

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 2/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 3: Composition/information on ingredients


Polyamide CAS: 68410-23-1 ≥50 - ≤75 Skin Irrit. 2, H315 [1]
Eye Dam. 1, H318
Xylene REACH #: ≥10 - ≤25 Flam. Liq. 3, H226 [1] [2]
01-2119488216-32 Acute Tox. 4, H312
EC: 215-535-7 Acute Tox. 4, H332
CAS: 1330-20-7 Skin Irrit. 2, H315
Index: 601-022-00-9 Eye Irrit. 2, H319
STOT SE 3, H335
STOT RE 2, H373
Asp. Tox. 1, H304
Solvent naphtha REACH #: ≥10 - <20 Flam. Liq. 3, H226 [1]
(petroleum), light arom. 01-2119455851-35 STOT SE 3, H335
EC: 265-199-0 STOT SE 3, H336
Index: 649-356-00-4 Asp. Tox. 1, H304
Aquatic Chronic 2, H411
EUH066
Tri REACH #: ≤10 Acute Tox. 4, H302 [1]
(dimethylaminomethyl) 01-2119560597-27 Skin Irrit. 2, H315
phenol EC: 202-013-9 Eye Irrit. 2, H319
CAS: 90-72-2
Index: 603-069-00-0
Ethylbenzene REACH #: ≤5 Flam. Liq. 2, H225 [1] [2]
01-2119489370-35 Acute Tox. 4, H332
EC: 202-849-4 STOT RE 2, H373 (hearing organs)
CAS: 100-41-4 Asp. Tox. 1, H304
Index: 601-023-00-4
Triethylene Tetramine EC: 203-950-6 ≤3 Acute Tox. 3, H311 [1]
CAS: 112-24-3 Skin Corr. 1B, H314
Index: 612-059-00-5 Eye Dam. 1, H318
Skin Sens. 1, H317
Aquatic Chronic 3, H412
See Section 16 for the full text of the H
statements declared above.

There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment, are PBTs or vPvBs or have been
assigned a workplace exposure limit and hence require reporting in this section.
Type
[1] Substance classified with a health or environmental hazard
[2] Substance with a workplace exposure limit
[3] Substance meets the criteria for PBT according to Regulation (EC) No. 1907/2006, Annex XIII
[4] Substance meets the criteria for vPvB according to Regulation (EC) No. 1907/2006, Annex XIII
[5] Substance of equivalent concern
Occupational exposure limits, if available, are listed in Section 8.
SECTION 4: First aid measures
4.1 Description of first aid measures
General : In all cases of doubt, or when symptoms persist, seek medical attention. Never give
anything by mouth to an unconscious person. If unconscious, place in recovery
position and seek medical advice.
Eye contact : Check for and remove any contact lenses. Immediately flush eyes with running
water for at least 15 minutes, keeping eyelids open. Seek immediate medical
attention.
Inhalation : Remove to fresh air. Keep person warm and at rest. If not breathing, if breathing is
irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by
trained personnel.
Skin contact : Remove contaminated clothing and shoes. Wash skin thoroughly with soap and
water or use recognised skin cleanser. Do NOT use solvents or thinners.

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 3/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 4: First aid measures


Ingestion : If swallowed, seek medical advice immediately and show the container or label.
Keep person warm and at rest. Do NOT induce vomiting.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. If it
is suspected that fumes are still present, the rescuer should wear an appropriate
mask or self-contained breathing apparatus. It may be dangerous to the person
providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing
thoroughly with water before removing it, or wear gloves.

4.2 Most important symptoms and effects, both acute and delayed
There are no data available on the mixture itself. Procedure used to derive the classification according to Regulation
(EC) No. 1272/2008 [CLP/GHS]. See Sections 2 and 3 for details.

Exposure to component solvent vapour concentrations in excess of the stated occupational exposure limit may result
in adverse health effects such as mucous membrane and respiratory system irritation and adverse effects on the
kidneys, liver and central nervous system. Symptoms and signs include headache, dizziness, fatigue, muscular
weakness, drowsiness and, in extreme cases, loss of consciousness.
Solvents may cause some of the above effects by absorption through the skin. Repeated or prolonged contact with
the mixture may cause removal of natural fat from the skin, resulting in non-allergic contact dermatitis and absorption
through the skin.
If splashed in the eyes, the liquid may cause irritation and reversible damage.
Ingestion may cause nausea, diarrhea and vomiting.
This takes into account, where known, delayed and immediate effects and also chronic effects of components from
short-term and long-term exposure by oral, inhalation and dermal routes of exposure and eye contact.

Contains 3,6-diazaoctanethylenediamin. May produce an allergic reaction.

4.3 Indication of any immediate medical attention and special treatment needed
Notes to physician : In case of inhalation of decomposition products in a fire, symptoms may be delayed.
The exposed person may need to be kept under medical surveillance for 48 hours.
Specific treatments : No specific treatment.

See toxicological information (Section 11)


SECTION 5: Firefighting measures
5.1 Extinguishing media
Suitable extinguishing : Recommended: alcohol-resistant foam, carbon dioxide, powders.
media
Unsuitable extinguishing : Do not use water jet.
media

5.2 Special hazards arising from the substance or mixture


Hazards from the : Fire will produce dense black smoke. Exposure to decomposition products may
substance or mixture cause a health hazard.
Hazardous thermal : Decomposition products may include the following materials: carbon monoxide,
decomposition products carbon dioxide, smoke, oxides of nitrogen.

5.3 Advice for firefighters


Special protective actions : Cool closed containers exposed to fire with water. Do not release runoff from fire to
for fire-fighters drains or watercourses.
Special protective : Fire-fighters should wear positive pressure self-contained breathing apparatus
equipment for fire-fighters (SCBA) and full turnout gear.

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 4/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 6: Accidental release measures


6.1 Personal precautions, protective equipment and emergency procedures
For non-emergency : Exclude sources of ignition and ventilate the area. Avoid breathing vapour or mist.
personnel Refer to protective measures listed in sections 7 and 8.
Keep unnecessary and unprotected personnel from entering.
For emergency responders : If specialised clothing is required to deal with the spillage, take note of any
information in Section 8 on suitable and unsuitable materials. See also the
information in "For non-emergency personnel".

6.2 Environmental : Do not allow to enter drains or watercourses. If the product contaminates lakes,
precautions rivers, or sewers, inform the appropriate authorities in accordance with local
regulations.

6.3 Methods and material : Contain and collect spillage with non-combustible, absorbent material e.g. sand,
for containment and earth, vermiculite or diatomaceous earth and place in container for disposal
cleaning up according to local regulations (see Section 13). Preferably clean with a detergent.
Avoid using solvents.
6.4 Reference to other : See Section 1 for emergency contact information.
sections See Section 8 for information on appropriate personal protective equipment.
See Section 13 for additional waste treatment information.
SECTION 7: Handling and storage
The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be
consulted for any available use-specific information provided in the Exposure Scenario(s).
7.1 Precautions for safe : Prevent the creation of flammable or explosive concentrations of vapours in air and
handling avoid vapour concentrations higher than the occupational exposure limits.
In addition, the product should only be used in areas from which all naked lights and
other sources of ignition have been excluded. Electrical equipment should be
protected to the appropriate standard.
Mixture may charge electrostatically: always use earthing leads when transferring
from one container to another.
Operators should wear antistatic footwear and clothing and floors should be of the
conducting type.
Keep away from heat, sparks and flame. No sparking tools should be used.
Avoid contact with skin and eyes. Avoid the inhalation of dust, particulates, spray or
mist arising from the application of this mixture. Avoid inhalation of dust from
sanding.
Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed.
Put on appropriate personal protective equipment (see Section 8).
Never use pressure to empty. Container is not a pressure vessel.
Always keep in containers made from the same material as the original one.
Comply with the health and safety at work laws.
Do not allow to enter drains or watercourses.
Information on fire and explosion protection
Vapours are heavier than air and may spread along floors. Vapours may form
explosive mixtures with air.

When operators, whether spraying or not, have to work inside the spray booth,
ventilation is unlikely to be sufficient to control particulates and solvent vapour in all
cases. In such circumstances they should wear a compressed air-fed respirator
during the spraying process and until such time as the particulates and solvent
vapour concentration has fallen below the exposure limits.

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 5/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 7: Handling and storage


7.2 Conditions for safe : Store in accordance with local regulations.
storage, including any Notes on joint storage
incompatibilities Keep away from: oxidising agents, strong alkalis, strong acids.
Additional information on storage conditions
Observe label precautions. Store in a dry, cool and well-ventilated area. Keep away
from heat and direct sunlight. Keep away from sources of ignition. No smoking.
Prevent unauthorised access. Containers that have been opened must be carefully
resealed and kept upright to prevent leakage.
Contaminated absorbent material may pose the same hazard as the spilt product.
Store in closed original container at temperatures between 5°C and 25°C.

7.3 Specific end use(s)


Recommendations : Not available.
Industrial sector specific : Not available.
solutions
Good housekeeping standards, regular safe removal of waste materials and regular maintenance of spray booth
filters will minimise the risks of spontaneous combustion and other fire hazards.
Before use of this material please refer to the Exposure Scenario(s) if attached for the specific end use,
control measures and additional PPE considerations.
SECTION 8: Exposure controls/personal protection
The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be
consulted for any available use-specific information provided in the Exposure Scenario(s).
8.1 Control parameters
Occupational exposure limits
Product/ingredient name Exposure limit values

Xylene EH40/2005 WELs (United Kingdom (UK), 12/2011). Absorbed


through skin.
STEL: 441 mg/m³ 15 minutes.
TWA: 50 ppm 8 hours.
TWA: 220 mg/m³ 8 hours.
STEL: 100 ppm 15 minutes.
Ethylbenzene EH40/2005 WELs (United Kingdom (UK), 12/2011). Absorbed
through skin.
STEL: 552 mg/m³ 15 minutes.
STEL: 125 ppm 15 minutes.
TWA: 100 ppm 8 hours.
TWA: 441 mg/m³ 8 hours.
Recommended monitoring : If this product contains ingredients with exposure limits, personal, workplace
procedures atmosphere or biological monitoring may be required to determine the effectiveness
of the ventilation or other control measures and/or the necessity to use respiratory
protective equipment. Reference should be made to monitoring standards, such as
the following: European Standard EN 689 (Workplace atmospheres - Guidance for
the assessment of exposure by inhalation to chemical agents for comparison with
limit values and measurement strategy) European Standard EN 14042 (Workplace
atmospheres - Guide for the application and use of procedures for the assessment
of exposure to chemical and biological agents) European Standard EN 482
(Workplace atmospheres - General requirements for the performance of procedures
for the measurement of chemical agents) Reference to national guidance
documents for methods for the determination of hazardous substances will also be
required.
: Regular monitoring of all work areas should be carried out at all times, including
areas that may not be equally ventilated.
DNELs/DMELs

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 6/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 8: Exposure controls/personal protection


No DNELs/DMELs available.
PNECs
No PNECs available

8.2 Exposure controls


Appropriate engineering : Provide adequate ventilation. Where reasonably practicable, this should be
controls achieved by the use of local exhaust ventilation and good general extraction. If
these are not sufficient to maintain concentrations of particulates and solvent
vapours below the OEL, suitable respiratory protection must be worn.
: Users are advised to consider national Occupational Exposure Limits or other
equivalent values.
Individual protection measures
Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Eye/face protection : Use safety eyewear designed to protect against splash of liquids.
Skin protection
Hand protection : Wear suitable gloves tested to EN374.
Gloves : Short Term Exposure less than 10 minutes Continuous use Nitrile gloves.
Hazardous ingredients Section 3 For more than 4 hours of protection in the
presence of Ethyl methyl ketone or Methyl ethyl ketone Acetone or Methyl isobutyl
ketone Butyl gloves 0.7mm For more than 4 hours of protection in the presence of
Aromatic solvent use polyvinyl alcohol (PVA) gloves.
Long Term Exposure Spill / For prolonged or repeated handling, use PE / PE
Laminate gloves > 8 hours (breakthrough time) .
There is no one glove material or combination of materials that will give unlimited
resistance to any individual or combination of chemicals.
The breakthrough time must be greater than the end use time of the product.
The instructions and information provided by the glove manufacturer on use,
storage, maintenance and replacement must be followed.
Gloves should be replaced regularly and if there is any sign of damage to the glove
material.
Always ensure that gloves are free from defects and that they are stored and used
correctly.
The performance or effectiveness of the glove may be reduced by physical/chemical
damage and poor maintenance.
Barrier creams may help to protect the exposed areas of the skin but should not be
applied once exposure has occurred.
The user must check that the final choice of type of glove selected for handling this
product is the most appropriate and takes into account the particular conditions of
use, as included in the user's risk assessment.
Body protection : Personnel should wear antistatic clothing made of natural fibres or of high-
temperature-resistant synthetic fibres.
: Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product. When there is a risk of ignition from static electricity,
wear anti-static protective clothing. For the greatest protection from static
discharges, clothing should include anti-static overalls, boots and gloves. Refer to
European Standard EN 1149 for further information on material and design
requirements and test methods.
Other skin protection : Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 7/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 8: Exposure controls/personal protection


Respiratory protection Use a properly fitted, particulate filter respirator complying with an approved
standard if a risk assessment indicates this is necessary. Recommended: A2P2
(EN14387). Respirator selection must be based on known or anticipated exposure
levels, the hazards of the product and the safe working limits of the selected
respirator.
Environmental exposure : Do not allow to enter drains or watercourses.
controls
Before use of this material please refer to the Exposure Scenario(s) if attached for the specific end use,
control measures and additional PPE considerations. The information contained in this safety data sheet
does not constitute the user’s own assessment of workplace risks, as required by other health and safety
legislation. The provisions of the national health and safety at work regulations apply to the use of this
product at work.
SECTION 9: Physical and chemical properties
9.1 Information on basic physical and chemical properties
Appearance
Physical state : Liquid.
Colour : Clear.
Odour : Paint
Odour threshold : Not Available (Not Tested).
pH : Testing not technically possible.
Melting point/freezing point Not Available (Not Tested).
Initial boiling point and : 136°C
boiling range
Flash point : Closed cup: 35°C [Pensky-Martens Closed Cup]
Evaporation rate : 0.8 (butyl acetate = 1)
Flammability (solid, gas) : Not Available (Not Tested).
Burning time Not Available (Not Tested).
Burning rate Not Available (Not Tested).
Upper/lower flammability or : Lower: 0.7%
explosive limits Upper: 7%
Vapour pressure : 0.13 kPa [at 20°C]
Vapour density : 3.66 [Air = 1]
Relative density : 0.93
Solubility(ies) Not Available (Not Tested).
Solubility in water : Not Available (Not Tested).
Partition coefficient: n-octanol/ Not Available (Not Tested).
water
Auto-ignition temperature : Not Available (Not Tested).
Decomposition temperature Not Available (Not Tested).
Viscosity : Kinematic (room temperature): <0.205 cm2/s
Kinematic (40°C): >0.07 cm2/s
Explosive properties
Oxidising properties : Under normal conditions of storage and use, hazardous reactions will not occur.

9.2 Other information


Heat of combustion : 17.45 kJ/g

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 8/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 10: Stability and reactivity


10.1 Reactivity : No specific test data related to reactivity available for this product or its ingredients.

10.2 Chemical stability : Stable under recommended storage and handling conditions (see Section 7).

10.3 Possibility of : Under normal conditions of storage and use, hazardous reactions will not occur.
hazardous reactions

10.4 Conditions to avoid : When exposed to high temperatures may produce hazardous decomposition
products.

10.5 Incompatible materials : Keep away from the following materials to prevent strong exothermic reactions:
oxidising agents, strong alkalis, strong acids.

10.6 Hazardous : Under normal conditions of storage and use, hazardous decomposition products
decomposition products should not be produced.
Refer to Section 7: HANDLING AND STORAGE and Section 8: EXPOSURE CONTROLS/PERSONAL
PROTECTION for additional handling information and protection of employees.
SECTION 11: Toxicological information
11.1 Information on toxicological effects
There are no data available on the mixture itself. Procedure used to derive the classification according to Regulation
(EC) No. 1272/2008 [CLP/GHS]. See Sections 2 and 3 for details.

Exposure to component solvent vapour concentrations in excess of the stated occupational exposure limit may result
in adverse health effects such as mucous membrane and respiratory system irritation and adverse effects on the
kidneys, liver and central nervous system. Symptoms and signs include headache, dizziness, fatigue, muscular
weakness, drowsiness and, in extreme cases, loss of consciousness.
Solvents may cause some of the above effects by absorption through the skin. Repeated or prolonged contact with
the mixture may cause removal of natural fat from the skin, resulting in non-allergic contact dermatitis and absorption
through the skin.
If splashed in the eyes, the liquid may cause irritation and reversible damage.
Ingestion may cause nausea, diarrhea and vomiting.
This takes into account, where known, delayed and immediate effects and also chronic effects of components from
short-term and long-term exposure by oral, inhalation and dermal routes of exposure and eye contact.

Contains 3,6-diazaoctanethylenediamin. May produce an allergic reaction.


Acute toxicity
Product/ingredient name Result Species Dose Exposure
Xylene LC50 Inhalation Gas. Rat 5000 ppm 4 hours
LD50 Oral Rat 4300 mg/kg -
Solvent naphtha (petroleum), LD50 Oral Rat 8400 mg/kg -
light arom.
Tri(dimethylaminomethyl) LD50 Dermal Rat 1280 mg/kg -
phenol
LD50 Oral Rat 1200 mg/kg -
Ethylbenzene LD50 Dermal Rabbit >5000 mg/kg -
LD50 Oral Rat 3500 mg/kg -
Triethylene Tetramine LD50 Dermal Rabbit 805 mg/kg -
LD50 Oral Rat 2500 mg/kg -
Acute toxicity estimates
Route ATE value
Oral 21801.4 mg/kg
Dermal 4694.4 mg/kg
Inhalation (gases) 24773.9 ppm
Inhalation (vapours) 308.3 mg/l

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 9/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 11: Toxicological information


Irritation/Corrosion
Product/ingredient name Result Species Score Exposure Observation
Xylene Eyes - Mild irritant Rabbit - 87 milligrams -
Eyes - Severe irritant Rabbit - 24 hours 5 -
milligrams
Skin - Mild irritant Rat - 8 hours 60 -
microliters
Skin - Moderate irritant Rabbit - 24 hours 500 -
milligrams
Skin - Moderate irritant Rabbit - 100 Percent -
Solvent naphtha (petroleum), Eyes - Mild irritant Rabbit - 24 hours 100 -
light arom. microliters
Tri(dimethylaminomethyl) Eyes - Severe irritant Rabbit - 24 hours 50 -
phenol Micrograms
Skin - Mild irritant Rat - 0.025 -
Mililiters
Skin - Severe irritant Rat - 0.25 Mililiters -
Skin - Severe irritant Rabbit - 24 hours 2 -
milligrams
Ethylbenzene Eyes - Severe irritant Rabbit - 500 -
milligrams
Skin - Mild irritant Rabbit - 24 hours 15 -
milligrams
Triethylene Tetramine Eyes - Moderate irritant Rabbit - 24 hours 20 -
milligrams
Eyes - Severe irritant Rabbit - 49 milligrams -
Skin - Severe irritant Rabbit - 24 hours 5 -
milligrams
Skin - Severe irritant Rabbit - 490 -
milligrams
Conclusion/Summary : Not available.
Sensitisation
No data available

Conclusion/Summary : Not available.


Mutagenicity
No data available
Carcinogenicity
No data available
Reproductive toxicity
No data available
Teratogenicity
No data available
Specific target organ toxicity (single exposure)
Product/ingredient name Category Route of Target organs
exposure
Xylene Category 3 Not applicable. Respiratory tract
irritation
Solvent naphtha (petroleum), light arom. Category 3 Not applicable. Respiratory tract
irritation and
Narcotic effects
Specific target organ toxicity (repeated exposure)

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 10/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 11: Toxicological information


Product/ingredient name Category Route of Target organs
exposure
Xylene Category 2 Not determined Not determined
Ethylbenzene Category 2 Not determined hearing organs
Aspiration hazard
Product/ingredient name Result
Xylene ASPIRATION HAZARD - Category 1
Solvent naphtha (petroleum), light arom. ASPIRATION HAZARD - Category 1
Ethylbenzene ASPIRATION HAZARD - Category 1

Other information : Not available.


SECTION 12: Ecological information
12.1 Toxicity
There are no data available on the mixture itself.
Do not allow to enter drains or watercourses.

Procedure used to derive the classification according to Regulation (EC) No. 1272/2008 [CLP/GHS]. See Sections 2
and 3 for details.
Product/ingredient name Result Species Exposure
Xylene Acute LC50 8500 μg/l Marine water Crustaceans - Palaemonetes 48 hours
pugio
Acute LC50 13400 μg/l Fresh water Fish - Pimephales promelas 96 hours
Ethylbenzene Acute EC50 4600 μg/l Fresh water Algae - Pseudokirchneriella 72 hours
subcapitata
Acute EC50 3600 μg/l Fresh water Algae - Pseudokirchneriella 96 hours
subcapitata
Acute EC50 6530 μg/l Fresh water Crustaceans - Artemia sp. - 48 hours
Nauplii
Acute EC50 2930 μg/l Fresh water Daphnia - Daphnia magna - 48 hours
Neonate
Acute LC50 4200 μg/l Fresh water Fish - Oncorhynchus mykiss 96 hours
Triethylene Tetramine Acute EC50 3700 μg/l Fresh water Algae - Pseudokirchneriella 96 hours
subcapitata
Acute LC50 33900 μg/l Fresh water Daphnia - Daphnia magna 48 hours

12.2 Persistence and degradability


Product/ingredient name Test Result Dose Inoculum
No data available
Conclusion/Summary : Not available.
Product/ingredient name Aquatic half-life Photolysis Biodegradability
Xylene - - Readily
Ethylbenzene - - Readily

12.3 Bioaccumulative potential


Product/ingredient name LogPow BCF Potential
Xylene - 8.1 to 25.9 low
Solvent naphtha (petroleum), - 10 to 2500 high
light arom.

12.4 Mobility in soil

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 11/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 12: Ecological information


Soil/water partition : Not available.
coefficient (KOC)
Mobility : Not available.

12.5 Results of PBT and vPvB assessment


PBT : Not applicable.
vPvB : Not applicable.

12.6 Other adverse effects : No known significant effects or critical hazards.


: Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains
and sewers.
SECTION 13: Disposal considerations
13.1 Waste treatment methods
Product
Methods of disposal : The generation of waste should be avoided or minimised wherever possible.
Disposal of this product, solutions and any by-products should at all times comply
with the requirements of environmental protection and waste disposal legislation
and any regional local authority requirements. Dispose of surplus and non-
recyclable products via a licensed waste disposal contractor. Waste should not be
disposed of untreated to the sewer unless fully compliant with the requirements of
all authorities with jurisdiction.
Hazardous waste : Yes.
European waste : waste paint and varnish containing organic solvents or other hazardous substances
catalogue (EWC) 08 01 11*
Disposal considerations : Do not allow to enter drains or watercourses.
Dispose of according to all federal, state and local applicable regulations.
If this product is mixed with other wastes, the original waste product code may no
longer apply and the appropriate code should be assigned.
For further information, contact your local waste authority.
Packaging
Methods of disposal : The generation of waste should be avoided or minimised wherever possible. Waste
packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible.
Disposal considerations : Using information provided in this safety data sheet, advice should be obtained from
the relevant waste authority on the classification of empty containers. Empty
containers must be scrapped or reconditioned. Dispose of containers contaminated
by the product in accordance with local or national legal provisions.
European waste : packaging containing residues of or contaminated by hazardous substances 15 01
catalogue (EWC) 10*
Special precautions : This material and its container must be disposed of in a safe way. Care should be
taken when handling emptied containers that have not been cleaned or rinsed out.
Empty containers or liners may retain some product residues. Vapour from product
residues may create a highly flammable or explosive atmosphere inside the
container. Do not cut, weld or grind used containers unless they have been cleaned
thoroughly internally. Avoid dispersal of spilt material and runoff and contact with
soil, waterways, drains and sewers.

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 12/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 14: Transport information


ADR/RID IMDG IATA
14.1 UN number UN1263 UN1263 UN1263

14.2 UN proper PAINT RELATED MATERIAL PAINT RELATED MATERIAL PAINT RELATED MATERIAL
shipping name
14.3 Transport 3 3 3
Hazard Class(es)/
Label(s)

14.4 Packing III III III


group
14.5 No. No. No.
Environmental
hazards
Additional Special provisions Emergency schedules Special provisions
information 640 (E) (EmS) Not Applicable
F-E, S-E
Tunnel code
D/E Special provisions
Not Applicable

14.6 Special precautions for : Transport within user’s premises: always transport in closed containers that are
user upright and secure. Ensure that persons transporting the product know what to do in
the event of an accident or spillage.

14.7 Transport in bulk : Not applicable.


according to Annex II of
Marpol and the IBC Code
Multi-modal shipping descriptions are provided for informational purposes and do not consider container
sizes. The presence of a shipping description for a particular mode of transport (sea, air, etc.), does not
indicate that the product is packaged suitably for that mode of transport. All packaging must be reviewed for
suitability prior to shipment, and compliance with the applicable regulations is the sole responsibility of the
person offering the product for transport. People loading and unloading dangerous goods must be trained on
all of the risks deriving from the substances and on all actions in case of emergency situations.
SECTION 15: Regulatory information
15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
EU Regulation (EC) No. 1907/2006 (REACH)
Annex XIV - List of substances subject to authorisation
Annex XIV
None of the components are listed.
Substances of very high concern
None of the components are listed.
Annex XVII - Restrictions : Not applicable.
on the manufacture,
placing on the market
and use of certain
dangerous substances,
mixtures and articles
Other EU regulations
VOC content (2010/75/EU) : 38.2 w/w

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 13/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 15: Regulatory information


354 g/l

Priority List Chemicals : Not determined


(793/93/EEC)
Seveso Directive
This product may add to the calculation for determining whether a site is within the scope of the Seveso Directive on
major accident hazards.
National regulations

15.2 Chemical safety : No Chemical Safety Assessment has been carried out.
assessment

SECTION 16: Other information


Indicates information that has changed from previously issued version.
Abbreviations and : ATE = Acute Toxicity Estimate
acronyms CLP = Classification, Labelling and Packaging Regulation [Regulation (EC) No.
1272/2008]
DMEL = Derived Minimal Effect Level
DNEL = Derived No Effect Level
EUH statement = CLP-specific Hazard statement
PBT = Persistent, Bioaccumulative and Toxic
PNEC = Predicted No Effect Concentration
RRN = REACH Registration Number
vPvB = Very Persistent and Very Bioaccumulative
Key literature references : Regulation (EC) No. 1272/2008 [CLP]
and sources for data ADR = The European Agreement concerning the International Carriage of
Dangerous Goods by Road
DPD = Dangerous Preparations Directive [1999/45/EC]
DSD = Dangerous Substances Directive [67/548/EEC]
IATA = International Air Transport Association
IMDG = International Maritime Dangerous Goods
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II, as amended by
Commission Regulation (EU) 2015/830
Directive 96/82/EC, and relative amendments & additions
Directive 2008/98/EC, and relative amendments & additions
Directive 2000/39/EC, and relative amendments & additions
CEPE Guidelines

Procedure used to derive the classification according to Regulation (EC) No. 1272/2008 [CLP/GHS]

Classification Justification
Flam. Liq. 3, H226 On basis of test data
Skin Irrit. 2, H315 Calculation method
Eye Dam. 1, H318 Calculation method
Skin Sens. 1, H317 Calculation method
STOT SE 3, H335 Calculation method
STOT RE 2, H373 Calculation method
Asp. Tox. 1, H304 Calculation method
Aquatic Chronic 3, H412 Calculation method

Full text of abbreviated H : H225 Highly flammable liquid and vapour.


statements H226 Flammable liquid and vapour.
H302 Harmful if swallowed.
H304 May be fatal if swallowed and enters airways.
H311 Toxic in contact with skin.
H312 Harmful in contact with skin.
H314 Causes severe skin burns and eye damage.
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 14/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 16: Other information


H318 Causes serious eye damage.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H335 May cause respiratory irritation.
H336 May cause drowsiness or dizziness.
H373 (hearing May cause damage to organs through prolonged or repeated
organs) exposure. (hearing organs)
H373 May cause damage to organs through prolonged or repeated
exposure.
H411 Toxic to aquatic life with long lasting effects.
H412 Harmful to aquatic life with long lasting effects.
Full text of classifications : Acute Tox. 3, H311 ACUTE TOXICITY (dermal) - Category 3
[CLP/GHS] Acute Tox. 4, H302 ACUTE TOXICITY (oral) - Category 4
Acute Tox. 4, H312 ACUTE TOXICITY (dermal) - Category 4
Acute Tox. 4, H332 ACUTE TOXICITY (inhalation) - Category 4
Aquatic Chronic 2, H411 LONG-TERM AQUATIC HAZARD - Category 2
Aquatic Chronic 3, H412 LONG-TERM AQUATIC HAZARD - Category 3
Asp. Tox. 1, H304 ASPIRATION HAZARD - Category 1
EUH066 Repeated exposure may cause skin dryness or cracking.
Eye Dam. 1, H318 SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 1
Eye Irrit. 2, H319 SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 2
Flam. Liq. 2, H225 FLAMMABLE LIQUIDS - Category 2
Flam. Liq. 3, H226 FLAMMABLE LIQUIDS - Category 3
Skin Corr. 1B, H314 SKIN CORROSION/IRRITATION - Category 1B
Skin Irrit. 2, H315 SKIN CORROSION/IRRITATION - Category 2
Skin Sens. 1, H317 SKIN SENSITIZATION - Category 1
STOT RE 2, H373 SPECIFIC TARGET ORGAN TOXICITY (REPEATED
(hearing organs) EXPOSURE) (hearing organs) - Category 2
STOT RE 2, H373 SPECIFIC TARGET ORGAN TOXICITY (REPEATED
EXPOSURE) - Category 2
STOT SE 3, H335 SPECIFIC TARGET ORGAN TOXICITY (SINGLE
EXPOSURE) (Respiratory tract irritation) - Category 3
STOT SE 3, H336 SPECIFIC TARGET ORGAN TOXICITY (SINGLE
EXPOSURE) (Narcotic effects) - Category 3
Date of printing : 16, May, 2016.

Date of issue/ Date of : 16, May, 2016.


revision
Date of previous issue : 09, May, 2016.

: If there is no previous validation date please contact your supplier for more
information.
Version : 5.01

Notice to reader
It is recommended that each customer or recipient of this Safety Data Sheet (SDS) study it carefully and
consult resources, as necessary or appropriate, to become aware of and understand the data contained in this
SDS and any hazards associated with the product. This information is provided in good faith and believed to
be accurate as of the effective date herein. However, no warranty, express or implied, is given. The information
presented here applies only to the product as shipped. The addition of any material can change the
composition, hazards and risks of the product. Regulatory requirements are subject to change and may differ
between various locations and jurisdictions. The customer/buyer/user is responsible to ensure that his
activities comply with all country, federal, state, provincial or local laws. The conditions for use of the product
are not under the control of the manufacturer; the customer/buyer/user is responsible to determine the
conditions necessary for the safe use of this product. The customer/buyer/user should not use the product for
any purpose other than the purpose shown in the applicable section of this SDS without first referring to the
supplier and obtaining written handling instructions. Due to the proliferation of sources for information such
as manufacturer-specific SDS, the manufacturer cannot be responsible for SDSs obtained from any other
source.

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 15/16
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
MACROPOXY M262 Epoxy Finish - Additive (Formerly known as Epigrip M262)
M262A

SECTION 16: Other information

Date of issue/Date of revision : 16, May, 2016. Date of previous issue : 09, May, 2016. Version : 5.01 16/16

You might also like