Activity 3.5.2: Subnetting Scenario 1: Topology Diagram

Activity 3.5.
2: Subnetting Scenario 1
Topology Diagram
Addressing Table
Device Interface IP Address Subnet Mask Default Gateway
Fa0/0 N/A
HQ S0/0/0 N/A
S0/0/1 N/A
Fa0/0 N/A
BRANCH1 Fa0/1 N/A
S0/0/0 N/A
Fa0/0 N/A
BRANCH2 Fa0/1 N/A
S0/0/1 N/A
PC1 NIC
PC2 NIC
PC3 NIC
PC4 NIC
PC5 NIC
All contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 4
CCNA Exploration
Routing Protocols and Concepts:
Introduction to Dynamic Routing Protocols Activity 3.5.2: Subnetting Scenario 1
Learning Objectives
Upon completion of this lab, you will be able to:
• Determine the number of subnets needed.
• Determine the number of hosts needed.
• Design an appropriate addressing scheme.
• Assign addresses and subnet mask pairs to device interfaces and hosts.
• Examine the use of the available network address space.
• Determine how static routing could be applied to the network.
Scenario
In this lab, you have been given the network address 192.168.9.0/24 to subnet and provide the IP
addressing for the network shown in the Topology Diagram. The network has the following addressing
requirements:
• The BRANCH1 LAN 1 will require 10 host IP addresses.
• The HQ LAN will require 20 host IP addresses.
• The link from HQ to BRANCH1 will require an IP address for each end of the link.
• The link from HQ to BRANCH2 will require an IP address for each end of the link.
Task 1: Examine the Network Requirements.

Examine the network requirements and answer the questions below. Keep in mind that IP addresses will
be needed for each of the LAN interfaces.
How many subnets are needed? __________
What is the maximum number of IP addresses that are needed for a single subnet? __________
How many IP addresses are needed for each of the branch LANs? __________
What is the total number of IP addresses that are needed? __________
Task 2: Design an IP Addressing Scheme.
Step 1: Subnet the 192.168.9.0 network into the appropriate number of subnets.
What will the subnet mask be for the subnetworks? __________________________
How many usable host IP addresses are there per subnet? __________
Fill in the following chart with the subnet information.
Subnet First Usable Last Usable Broadcast

Subnet Address
Number Host Address Host Address Address
0
1
2
3
4
CCNA Exploration
Subnet First Usable Last Usable Broadcast

Subnet Address
Number Host Address Host Address Address
5
6
7
Step 2: Assign the subnets to the network shown in the Topology Diagram.
When assigning the subnets, keep in mind that routing will need to occur to allow information to be sent
throughout the network. The subnets will be assigned to the networks to allow for route summarization on
each of the routers.
1. Assign subnet 1 to the BRANCH2 LAN 2: ____________________
2. Assign subnet 2 to BRANCH2 LAN 1 subnet address: ____________________
3. Assign subnet 3 to link from HQ to BRANCH2 subnet address: ____________________
4. Assign subnet 4 to HQ LAN subnet address: ____________________
5. Assign subnet 5 to link from HQ to BRANCH1 subnet address: ____________________
Task 3: Assign IP Addresses to the Network Devices

Assign the appropriate addresses to the device interfaces. Document the addresses to be used in the
Addressing Table provided under the Topology Diagram.
Step 1: Assign addresses to the HQ router.

1. Assign the first valid host address in the HQ LAN subnet to the LAN interface.
2. Assign the first valid host address in link from HQ to BRANCH1 subnet to the S0/0/0 interface.
3. Assign the first valid host address in link from HQ to BRANCH2 subnet to the S0/0/1 interface.
Step 2: Assign addresses to the BRANCH1 router.

1. Assign the first valid host address in the BRANCH1 LAN 1 subnet to the Fa0/0 LAN interface.
3. Assign the last valid host address in link from HQ to BRANCH1 subnet to the WAN interface.
Step 3: Assign addresses to the BRANCH2 router.

3. Assign the last valid host address in link from HQ to BRANCH2 subnet to the WAN interface.
Step 4: Assign addresses to the host PCs.

1. Assign the last valid host address in the HQ LAN subnet to PC1.
2. Assign the last valid host address in the BRANCH1 LAN 1 subnet to PC2.
CCNA Exploration
Task 4: Test the Network Design.

Apply your addressing scheme to the Packet Tracer file that has been supplied with this lab. Check to see
that all devices on directly connected networks can ping each other.
Task 5: Reflection
How many IP address in the 192.168.9.0 network are wasted in this design? __________
What would the command be to add a default static route on the WAN interface of the BRANCH1 router?
___________________________________________________________________________________
Can both of the BRANCH1 LANs be summarized into one route on the HQ router? _________
What would be the command used to add this summary route to the routing table?
___________________________________________________________________________________
Can both of the BRANCH2 LANs be summarized into one route on the HQ router? __________
___________________________________________________________________________________
Can the HQ LAN and both of the BRANCH1 LANs be summarized into one route on the BRANCH2
router? This summarized route should also include the link between the HQ and BRANCH1 routers.
__________
___________________________________________________________________________________

Activity 3.5.2: Subnetting Scenario 1: Topology Diagram

Uploaded by

Copyright:

Available Formats

Activity 3.5.2: Subnetting Scenario 1: Topology Diagram

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Activity 3.5.2: Subnetting Scenario 1: Topology Diagram

Uploaded by

Copyright:

Available Formats

Activity 3.5.

Device Interface IP Address Subnet Mask Default Gateway

Task 1: Examine the Network Requirements.

Task 2: Design an IP Addressing Scheme.

Subnet First Usable Last Usable Broadcast

Subnet First Usable Last Usable Broadcast

Task 3: Assign IP Addresses to the Network Devices

Step 1: Assign addresses to the HQ router.

Step 2: Assign addresses to the BRANCH1 router.

Step 3: Assign addresses to the BRANCH2 router.

Step 4: Assign addresses to the host PCs.

Task 4: Test the Network Design.

You might also like