En ERouting SLM v4050 Chap 1 Lab153

Lab 1.5.
3: Challenge Router Configuration
Topology Diagram
Addressing Table
Device Interface IP Address Subnet Mask Default Gateway
Fa0/0 N/A
R1
S0/0/0 N/A
Fa0/0 N/A
R2
S0/0/0 N/A
PC1 NIC
PC2 NIC
Learning Objectives
Upon completion of this lab, you will be able to:
Subnet an address space given requirements.
Assign appropriate addresses to interfaces and document.
Cable a network according to the Topology Diagram.
Erase the startup configuration and reload a router to the default state.
Perform basic configuration tasks on a router.
Configure and activate Serial and Ethernet interfaces.
Test and verify configurations.
Reflect upon and document the network implementation.
Scenario
In this lab activity, you will design and apply an IP addressing scheme for the topology shown in the
Topology Diagram. You will be given one class C address that you must subnet to provide a logical
addressing scheme for the network. You must first cable the network as shown before the configuration
can begin. Once the network is cabled, configure each device with the appropriate basic configuration
commands. The routers will then be ready for interface address configuration according to your IP
addressing scheme. When the configuration is complete, use the appropriate IOS commands to verify
that the network is working properly.
Note: Use classful subnetting for this lab.
All contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 4
CCNA Exploration
Routing Protocols and Concepts:
Introduction to Routing and Packet Forwarding Lab 1.5.3: Challenge Router Configuration
Task 1: Subnet the Address Space.
Step 1: Examine the network requirements.

You have been given the 192.168.1.0/24 address space to use in your network design. The network
consists of the following segments:
The network connected to router R1 will require enough IP addresses to support 20 hosts.
The network connected to router R2 will require enough IP addresses to support 20 hosts.
The link between router R1 and router R2 will require IP addresses at each end of the link.
(Note: Remember that the interfaces of network devices are also host IP addresses and are included
in the above addressing scheme.)
Step 2: Consider the following questions when creating your network design.
How many subnets are needed for this network? ____________________
What is the subnet mask for this network in dotted decimal format? ____________________
What is the subnet mask for the network in slash format? ____________________
How many usable hosts are there per subnet? ____________________
Step 3: Assign subnetwork addresses to the Topology Diagram.

1. Assign the first subnet (lowest subnet) to the network attached to R1.
2. Assign the second subnet to the link between R1 and R2.
3. Assign the third subnet to the network attached to R2.
Task 2: Determine Interface Addresses.
Step 1: Assign appropriate addresses to the device interfaces.

1. Assign the first valid host address in first subnet to the LAN interface on R1.
2. Assign the last valid host address in first subnet to PC1.
3. Assign the first valid host address in second subnet to the WAN interface on R1.
4. Assign the last valid host address in second subnet to the WAN interface on R2.
5. Assign the first valid host address in third subnet to the LAN interface of R2.
6. Assign the last valid host address in third subnet to PC2.
Note: The fourth (highest) subnet is not required in this lab.
Step 2: Document the addresses to be used in the table provided under the Topology Diagram.
Task 3: Prepare the Network
Step 1: Cable a network that is similar to the one in the Topology Diagram.
You can use any current router in your lab as long as it has the required interfaces as shown in the
topology.
Step 2: Clear any existing configurations on the routers.
CCNA Exploration
Task 4: Perform Basic Router Configurations.

Perform basic configuration of the R1 and R2 routers according to the following guidelines:
1. Configure the router hostname.
2. Disable DNS lookup.
3. Configure an EXEC mode password.
4. Configure a message-of-the-day banner.
5. Configure a password for console connections.
6. Configure a password for VTY connections.
Task 5: Configure and Activate Serial and Ethernet Addresses.
Step 1: Configure the router interfaces.

Configure the interfaces on the R1 and R2 routers with the IP addresses from your network design. When
you have finished, be sure to save the running configuration to the NVRAM of the router.
Step 2: Configure the PC interfaces.

Configure the Ethernet interfaces of PC1 and PC2 with the IP addresses and default gateways from your
network design.
Task 6: Verify the Configurations.

Answer the following questions to verify that the network is operating as expected.
From the host attached to R1, is it possible to ping the default gateway? __________
From the host attached to R2, is it possible to ping the default gateway? __________
From the router R1, is it possible to ping the Serial 0/0/0 interface of R2? __________
From the router R2, is it possible to ping the Serial 0/0/0 interface of R1? __________
The answer to the above questions should be yes. If any of the above pings failed, check your physical
connections and configurations. If necessary, refer to Lab 1.5.2, “Basic Router Configuration.”
What is the status of the FastEthernet 0/0 interface of R1? _____________
What is the status of the Serial 0/0/0 interface of R1? _____________
What is the status of the FastEthernet 0/0 interface of R2? _____________
What is the status of the Serial 0/0/0 interface of R2? _____________
CCNA Exploration
What routes are present in the routing table of R1?

__________________________________________________________________________
__________________________________________________________________________
What routes are present in the routing table of R2?

__________________________________________________________________________
__________________________________________________________________________
Task 7: Reflection
Are there any devices on the network that cannot ping each other?
__________________________________________________________________________
__________________________________________________________________________
What is missing from the network that is preventing communication between these devices?
__________________________________________________________________________
__________________________________________________________________________
Task 8: Document the Router Configurations.

On each router, capture the following command output to a text (.txt) file and save for future reference.
Running configuration
Routing table
Summary of status information for each interface

En ERouting SLM v4050 Chap 1 Lab153

Uploaded by

Copyright:

Available Formats

En ERouting SLM v4050 Chap 1 Lab153

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

En ERouting SLM v4050 Chap 1 Lab153

Uploaded by

Copyright:

Available Formats

Lab 1.5.

3: Challenge Router Configuration

Device Interface IP Address Subnet Mask Default Gateway

Task 1: Subnet the Address Space.

Step 1: Examine the network requirements.

How many usable hosts are there per subnet? ____________________

Step 3: Assign subnetwork addresses to the Topology Diagram.

Task 2: Determine Interface Addresses.

Step 1: Assign appropriate addresses to the device interfaces.

Task 3: Prepare the Network

Step 2: Clear any existing configurations on the routers.

Task 4: Perform Basic Router Configurations.

Task 5: Configure and Activate Serial and Ethernet Addresses.

Step 1: Configure the router interfaces.

Step 2: Configure the PC interfaces.

Task 6: Verify the Configurations.

What is the status of the Serial 0/0/0 interface of R1? _____________

What is the status of the FastEthernet 0/0 interface of R2? _____________

What is the status of the Serial 0/0/0 interface of R2? _____________

What routes are present in the routing table of R1?

What routes are present in the routing table of R2?

Task 8: Document the Router Configurations.

You might also like