Professional Documents
Culture Documents
NX-200G/ NX-300G: Instruction Manual
NX-200G/ NX-300G: Instruction Manual
MIC
1 3 DEF
2 ABC
4 GHI MN
O
6
5 JKL
7 PQR Z
S 9 WXY
8 TUV
#
0
B5A-0160-10 (E)
THANK YOU
We are grateful you have chosen KENWOOD for your land
mobile radio applications.
Firmware Copyrights
The title to and ownership of copyrights for firmware
embedded in KENWOOD product memories are reserved
for JVC KENWOOD Corporation.
i
PRECAUTIONS
• Do not charge the transceiver and battery pack when they are wet.
• Ensure that there are no metallic items located between the
transceiver and the battery pack.
• Do not use options not specified by KENWOOD.
• If the die-cast chassis or other transceiver part is damaged, do not
touch the damaged parts.
• If a headset or headphone is connected to the transceiver, reduce
the transceiver volume. Pay attention to the volume level when
turning the squelch off.
• Do not place the microphone cable around your neck while near
machinery that may catch the cable.
• Do not place the transceiver on unstable surfaces.
• Ensure that the end of the antenna does not touch your eyes.
• When the transceiver is used for transmission for many hours, the
radiator and chassis will become hot. Do not touch these locations
when replacing the battery pack.
• Always switch the transceiver power off before installing optional
accessories.
• The charger is the device that disconnects the unit from the AC
mains line. The AC plug should be readily accessible.
ii
Turn the transceiver power off in the following locations:
• Near explosives or blasting sites.
• In aircrafts. (Any use of the transceiver must follow the
instructions and regulations provided by the airline crew.)
• Where restrictions or warnings are posted regarding the use of
radio devices, including but not limited to medical facilities.
• Near persons wearing pacemakers.
Turn the transceiver power off in the following locations,
unless the model is specifically qualified for such use
(Intrinsically Safe such as approved by Factory Mutual, CSA):
• In explosive atmospheres (inflammable gas, dust particles,
metallic powders, grain powders, etc.).
• While taking on fuel or while parked at gasoline service stations.
• Do not remove the black sheet from the reverse side of the
transceiver (refer to the illustration below). Removal of this
sheet decreases the waterproof efficiency of the transceiver and
may cause malfunctions if water seeps into the transceiver.
• The orange seal on the reverse side of the transceiver is
important with respect to the waterproof efficiency of the
transceiver. Do not place stickers or other materials on or
around the seal shown in the figure, or on the reverse side of
the battery pack. Doing so will impair the waterproof efficiency
of the transceiver and may cause it to break down. Additionally,
in order to prevent damage to the seal, do not allow it to come
in contact with foreign materials.
iii
• Do not disassemble or modify the transceiver for any reason.
• Do not place the transceiver on or near airbag equipment while
the vehicle is running. When the airbag inflates, the transceiver
may be ejected and strike the driver or passengers.
• Do not transmit while touching the antenna terminal or if
any metallic parts are exposed from the antenna covering.
Transmitting at such a time may result in a high-frequency burn.
• If an abnormal odor or smoke is detected coming from the
transceiver, switch the transceiver power off immediately,
remove the battery pack from the transceiver, and contact your
KENWOOD dealer.
• Use of the transceiver while you are driving may be against
traffic laws. Please check and observe the vehicle regulations
in your area.
• Do not expose the transceiver to extremely hot or cold
conditions.
• Do not carry the battery pack (or battery case) with metal
objects, as they may short the battery terminals.
• Danger of explosion if the battery is incorrectly replaced;
replace only with the same type.
• When attaching a commercial strap to the transceiver, ensure
that the strap is durable. In addition, do not swing the transceiver
around by the strap; you may inadvertently strike and injure
another person with the transceiver.
• If a commercially available neck strap is used, take care not to
let the strap get caught on nearby machine.
• When operating the transceiver in areas where the air is dry,
it is easy to build up an electric charge (static electricity).
When using an earphone accessory in such conditions, it is
possible for the transceiver to send an electric shock through
the earphone and to your ear. We recommend you use only
a speaker/microphone in these conditions, to avoid electric
shocks.
iv
NOTIFICATION OF WATER-RESISTANT MODEL
Water Resistance and Maintenance
This transceiver conforms to the following standards:
IP67: The IP standard is the protection level specified by the
international standard IEC 60529. The first numeral indicates the “dust-
resistant” level and the second numeral indicates the “water-resistant”
level.
PRECAUTIONS
• The applicable standards listed above do not assure that the
transceiver can be used in water. The transceiver may be
damaged in a situation in which the maximum depth is over
1 meter or the maximum submersion time exceeds 30 minutes.
• Observe the following precautions to maintain the transceiver’s
water-resistant performance:
a) Do not drop or apply strong physical shocks to the transceiver.
b) When you disassemble the transceiver or open the cover of
the option board, IP67 will no longer be maintained. After
disassembling the transceiver or opening the cover of the
option board, if you want to continue maintaining IP67, contact
your dealer or Authorized Service Center.
c) Do not soak the transceiver in water that contains a solvent or
surfactant, such as detergent or alcohol.
• If it is soaked in muddy water or salt water (including sea water),
it may become corroded. Immediately flush with fresh water and
then wipe dry with a soft cloth.
• If water is splashed onto the microphone, the battery, or the
antenna terminal, clean and dry them with a soft cloth before
reconnecting to the transceiver.
• When water gets into the microphone opening or the speaker
grill, the voice level may become low or distorted. Lightly shake
the transceiver to remove the water from the speaker and/or
microphone before operating the transceiver.
• Use of any option on the transceiver not specified by KENWOOD,
may reduce or void the water resistant and dust resistant
performance.
• When using an option with the transceiver, ensure that it
corresponds with the IP67 standard.
v
INFORMATION CONCERNING THE LI-ION BATTERY PACK:
The battery pack includes flammable objects such as organic solvent.
Mishandling may cause the battery to rupture producing flames or
extreme heat, deteriorate, or cause other forms of damage to the
battery. Please observe the following prohibitive matters.
vi
• Do not charge the battery near fires or under direct
sunlight!
If the battery’s protection circuit is damaged, the battery
may charge at extreme current (or voltage) and an abnormal
chemical reaction may occur. The battery may generate heat or
smoke, rupture, or burst into flame.
• Use only the specified charger and observe charging
requirements!
If the battery is charged in unspecified conditions (under high
temperature over the regulated value, excessive high voltage or
current over regulated value, or with a remodelled charger), it
may overcharge or an abnormal chemical reaction may occur.
The battery may generate heat or smoke, rupture, or burst into
flame.
• Do not pierce the battery with any object, strike it with an
instrument, or step on it!
This may break or deform the battery, causing a short-circuit.
The battery may generate heat or smoke, rupture, or burst into
flame.
• Do not jar or throw the battery!
An impact may cause the battery to leak, generate heat
or smoke, rupture, and/or burst into flame. If the battery’s
protection circuit is damaged, the battery may charge at an
abnormal current (or voltage), and an abnormal chemical
reaction may occur.
• Do not use the battery pack if it is damaged in any way!
The battery may generate heat or smoke, rupture, or burst into
flame.
• Do not solder directly onto the battery!
If the insulator is melted or the gas release vent or safety
function is damaged, the battery may generate heat or smoke,
rupture, or burst into flame.
• Do not reverse the battery polarity (and terminals)!
When charging a reversed battery, an abnormal chemical
reaction may occur. In some cases, an unexpected large
amount of current may flow upon discharging. The battery may
generate heat or smoke, rupture, or burst into flame.
vii
• Do not reverse-charge or reverse-connect the battery!
The battery pack has positive and negative poles. If the battery
pack does not smoothly connect with a charger or operating
equipment, do not force it; check the polarity of the battery. If
the battery pack is reverse-connected to the charger, it will be
reverse-charged and an abnormal chemical reaction may occur.
The battery may generate heat or smoke, rupture, or burst into
flame.
• Do not touch a ruptured and leaking battery!
If the electrolyte liquid from the battery gets into your eyes,
wash your eyes out with fresh water as soon as possible,
without rubbing your eyes. Go to the hospital immediately. If
left untreated, it may cause eye-problems.
viii
CONTENTS
UNPACKING AND CHECKING EQUIPMENT ..............................1
PREPARATION ...............................................................2
GETTING ACQUAINTED .....................................................5
PROGRAMMABLE FUNCTIONS............................................8
BASIC OPERATIONS ...................................................... 10
MENU MODE ............................................................... 13
SCAN ........................................................................ 16
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION ............ 18
5-TONE SIGNALING ....................................................... 21
ADVANCED OPERATIONS ................................................ 24
BACKGROUND OPERATIONS ............................................ 30
VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT .................. 33
SUPPLIED ACCESSORIES
Belt clip ........................................................................................ 1
• Screws for belt clip (M3 x 8 mm) ............................................ 2
Universal connector cap .............................................................. 1
• Dressing screw (preassembled) ............................................. 1
• Packing (preassembled) ............................................................... 1
Quick reference guide ....................................................................... 1
1
PREPARATION
INSTALLING/ REMOVING THE (OPTIONAL) BATTERY PACK
1 Match the guides of the battery pack with the grooves on
the upper rear of the transceiver, then firmly press the
battery pack in place.
2 Lock the safety catch to prevent accidentally releasing the
battery pack.
3 To remove the battery pack, lift the safety catch, press the
release latch, then pull the battery pack away from the
transceiver.
Safety catch
3
1 Release latch
2
Note:
◆ For battery pack charging procedures and usage, refer to the
battery charger Instruction Manual.
◆ Before charging a battery pack that is attached to the
transceiver, ensure that the safety catch is firmly closed.
◆ While operating the transceiver using a Li-ion battery pack in
areas with an ambient temperature of –10°C/ +14°F and lower,
operating time may be shortened.
◆ Install the battery pack after cleaning the battery pack contacts
and the transceiver terminals.
2
INSTALLING THE (OPTIONAL) ANTENNA
Screw the antenna into the connector Optional
on the top of the transceiver by holding antenna
the antenna at its base and turning
it clockwise until secure.
M3 x 8 mm
screws
3
INSTALLING THE CAP OVER THE UNIVERSAL CONNECTOR
Universal
M
IC
connector cap
M
IC
Optional
1
4
GH
speaker/ microphone
I 2 ABC
3 DEF
7
PQ
RS 5JKL
6 MNO
8 TUV
9 WXYZ
0
#
4
GETTING ACQUAINTED
KEYS AND CONTROLS
Antenna
Display
Microphone MIC
Speaker
1 3 DEF
2 ABC
4 GHI O
6 MN
5 JKL
7 PQ YZ
RS 9 WX
8 TUV
#
0
a Selector knob
Rotate to select a zone or channel/group ID (default).
b Power switch/ Volume control
Rotate to turn the transceiver ON/OFF and to adjust the
volume.
c Auxiliary key
Press to activate its programmable function {page 8}.
d Transmit/ Receive/ Battery low indicator
If enabled by your dealer, lights red while transmitting,
green while receiving a call (Conventional channels only),
and orange when receiving an optional signaling call. Blinks
red when the battery power is low while transmitting.
e PTT (Push-To-Talk) switch
Press and hold this switch, then speak into the microphone
to call a station.
5
f Side 1 key
Press to activate its programmable function {page 8}.
The default is [Squelch Off Momentary].
g Side 2 key
Press to activate its programmable function {page 8}.
The default is [Backlight].
h Keypad (keypad models only)
Press these keys to send DTMF tones. These keys can
also be programmed with secondary functions {page 8} if a
programmable function key is programmed as [Function].
i key
Press to activate its programmable function {page 8}.
The default is [Menu].
j key
Press to activate its programmable function {page 8}.
The default is [Zone Up].
k key
Press to activate its programmable function {page 8}.
The default is [None].
l key
Press to activate its programmable function {page 8}.
The default is [None].
m key
Press to activate its programmable function {page 8}.
The default is [Zone Down].
n key
Press to activate its programmable function {page 8}.
The default is [None].
o Universal connector
Connect a speaker/ microphone or headset here {page 4}.
Otherwise, keep the supplied cap in place.
6
DISPLAY
Indicator Description
Monitor or Squelch Off is activated.
Blinks when an incoming call matches your Optional
Signaling.
The current zone (left icon) or CH/GID (right icon) is
added to scan.
Scan is in progress. Blinks while scan is paused.
A message is stored in memory. Blinks when a new
message has arrived.
The current channel is a Priority channel.
Operator Selectable Tone (OST) is activated.
Signal strength indicator {page 31}.
Battery power indicator {page 31}.
Talk Around is activated.
Site Lock is activated.
Scrambler/ Encryption is activated.
Auto Recording on the VGS-1 option is activated.
Auto Reply Message on the VGS-1 option is activated.
The auxiliary function is activated.
Lone Worker is activated.
The channel is using high transmit power. “L”
appears when using low transmit power.
VOX is activated.
The vibrator is activated. Blinks when inhibited.
Displays the time.
Displays the key functions for , , and .
7
PROGRAMMABLE FUNCTIONS
Following is a list of available programmable functions. Please
contact your dealer for further details on those functions which
have been programmed on your transceiver.
8
• Site Up/Down 5 • Transceiver Password
• Speaker Attenuation 11 • Vibrator
• Squelch Level 1 • Voice Memo 2
• Squelch Off 1 • VOX 10
• Squelch Off Momentary 1 • Zone Delete/Add
• Stack • Zone Down
• Status (Analog/NXDN) • Zone Select 5
• Talk Around 9 • Zone Up
1
Available only for Analog Conventional operation.
2
Available only if the VGS-1 optional board has been installed.
3
Available only for Analog Conventional and Analog Trunking
operation.
4
Available only for NXDN Trunking operation.
5
Can be programmed only on the Selector knob.
6
Available only for NXDN Conventional operation.
7
Can be programmed only on the Auxiliary key and the optional
speaker/ microphone PF1 (orange) key.
8
Available only for NXDN Conventional and NXDN Trunking operation.
9
Available only for Analog Conventional, Analog Trunking, and NXDN
Conventional operation.
10
Available only for Analog Conventional and NXDN Conventional
operation.
11
Can be programmed only on the microphone programmable function
keys.
12
Available only for 5-tone calls.
9
BASIC OPERATIONS
SWITCHING POWER ON/OFF
Turn the Power switch/ Volume control clockwise to switch the
transceiver ON.
Turn the Power switch/ Volume control counterclockwise fully
to switch the transceiver OFF.
■ Transceiver Password
If the transceiver is password protected, “PASSWORD” will
appear on the display when the power is turned ON. To
unlock the transceiver, enter the password:
1 Select a character using .
• On keypad models, you can enter the password directly.
2 Press to enter the selected character.
• This step is unnecessary when using the keypad.
3 Repeat steps 1 and 2 to enter the entire password.
• Press or # to delete a character. Press and hold or
# to delete all characters.
4 Press or to confirm the entry.
• If you enter an incorrect password, an error tone sounds
and the transceiver remains locked.
• The password can contain a maximum of 6 digits.
10
Select the desired channel/group ID using the Selector knob
(default). Each channel/group ID is programmed with settings
for transmitting and receiving.
• You can toggle the display between the zone and channel/group
ID names and number by pressing the key programmed as Display
Format, or by accessing the Menu {page 13}.
Note: If the default settings for / and the Selector knob
have been changed, use the appropriate keys to select the zone
and channel/group ID.
TRANSMITTING
1 Select the desired zone and channel/group ID.
2 Press the key programmed as [Monitor] or [Squelch Off]
to check whether or not the channel is free.
• If the channel is busy, wait until it becomes free.
3 Press the PTT switch and speak into the microphone.
Release the PTT switch to receive.
• For best sound quality, hold the transceiver approximately
1.5 inches (3 cm to 4 cm) from your mouth.
■ Making Group Calls (Digital)
If a key has been programmed with [Group] or [Group +
Status], you can select a group ID from the list to make a
call to those parties on a Conventional channel.
To select a group ID:
1 Press the key programmed as [Group] or [Group +
Status].
2 Press / to select a group ID/name from the list.
3 Press and hold the PTT switch to make the call.
• Speak into the transceiver as you would during a normal
transmission.
11
■ Making Individual Calls (Digital)
If a key has been programmed with [Individual] or
[Individual + Status], you can make calls to specific
persons.
1 Press the key programmed as [Individual] or
[Individual + Status].
2 Press / to select a unit ID from the list.
• On keypad models, you can enter a unit ID directly.
3 Press and hold the PTT switch to make the call.
• Speak into the transceiver as you would during a normal
transmission.
RECEIVING
Select the desired zone and channel. If signaling has been
programmed on the selected channel, you will hear a call only
if the received signal matches your transceiver settings.
Note: Signaling allows your transceiver to code your calls. This will
prevent you from listening to unwanted calls. Refer to “SIGNALING”
{page 27} for details.
12
MENU MODE
Many functions on this transceiver are selected or configured through
the Menu instead of physical controls. Once you become familiar with
the Menu system, you will appreciate the versatility it offers.
MENU ACCESS
1 Press the key programmed as [Menu].
• The category list is shown.
• When there is only 1 category, the function list is
shown (proceed to step 4).
2 Press / to select a category item.
• On keypad models, you can enter a category number directly.
3 Press or to view the function list.
4 Press / to select a function item.
• On keypad models, you can enter a function number directly.
5 Press or to set up the selected function item.
• Press or # to return to the category list.
6 Press / to select your desired setting.
• For settings with more than 1 level, repeat steps 5 and 6.
7 Press or to set the selected setting and exit Menu mode.
• Press or # at any time to return to the previous display.
• Press at any time to exit Menu mode.
MENU CONFIGURATION
Some transceiver keys may already be programmed with
functions listed in the Menu. Those functions can be accessed
directly by pressing the key. All other functions can still be
accessed using the transceiver Menu. The following table lists
the available Menu items.
Display Description
AUTO REPLY MSG Auto Reply Message ON/OFF
AUTO DIAL Autodial Mode
AUTO DIAL PROG Autodial Programming Mode
AUX AUX ON/OFF
BROADCAST Broadcast ON/OFF
CLOCK Clock ON/OFF
CLOCK ADJUST Clock Adjustment Mode
DIRECT CH1 SEL Direct CH/GID 1 ~ 5 Select
13
Display Description
DISP FORMAT Display Format ON/OFF
EXT MIC TYPE External Microphone Type Mode
FIXED VOLUME Fixed Volume
FORCED SEARCH Forced Search
GPS POS DISP GPS Position Display Mode
GROUP Group Mode
GROUP+STATUS Group + Status Mode
GROUP+SDM Group + SDM Mode
HIGH TX POWER High Transmission Power ON/OFF
HOME CH SEL Home CH/GID Select
INDIVIDUAL Individual Mode
INDIV+STATUS Individual + Status Mode
INDIV+SDM Individual + SDM Mode
LONE WORKER Lone Worker ON/OFF
LOW TX POWER Low Transmission Power ON/OFF
MAINTENANCE Maintenance Display Mode
MONITOR Monitor ON/OFF
OST OST ON/OFF
OST LIST OST Mode
PLAYBACK Playback Mode
PRI CH SEL Priority Channel Select Mode
RX AUDIO EQ RX Audio Equalizer Mode
RX AGC RX Audio Gain Control Mode
RX LOW CUT RX Low Cut Mode
RECEIVE ENTRY Receive Entry Mode
SCAN Scan ON/OFF
SCAN DEL/ADD Scan Delete/Add
SCRAM/ENCRYP Scrambler/Encryption ON/OFF
SCRAM CODE Scrambler/Encryption Code Mode
SELCALL Selcall Mode
SELCALL+STATUS Selcall + Status Mode
SELCALL+SDM Selcall + SDM Mode
SEND GPS DATA Transmit your GPS data
SITE LOCK Site Lock ON/OFF
SITE No. Display Site Number
SITE Site Select Mode
SQUELCH LEVEL Squelch Level Mode
14
Display Description
SQUELCH OFF Squelch Off ON/OFF
STACK Stack Mode
STATUS Status Mode
SHORT MESSAGE Short Message Mode
TALK AROUND Talk Around ON/OFF
TX AUDIO EQ TX Audio Equalizer Mode
TX AGC TX Audio Gain Control Mode
TX NOISE SUPPR TX Noise Suppressor Mode
PASSWORD Transceiver Password Mode
VIBRATOR Vibrator ON/OFF
VOICE MEMO Voice Memo Mode
VOX LEVEL VOX Level Mode
VOX VOX ON/OFF
ZONE DEL/ADD Zone Delete/Add
CHARACTER ENTRY
There are 2 methods available for entering characters:
1) Pressing the / keys
Press / to cycle the characters from A ~ Z, 0 ~ 9,
and a space (default settings).
You can also assign a character to an optional key and later
press that key to recall the assigned character: A ~ Z, a ~ z,
0 ~ 9, or a space and characters.
2) Using the DTMF keypad
Press the keypad keys to enter characters as shown in the
table below:
DTMF Key Character Cycle DTMF Key Character Cycle
1 1 6 M N O 6
2 A B C 2 7 P Q R S 7
3 D E F 3 8 T U V 8
4 G H I 4 9 W X Y Z 9
5 J K L 5 0 [space] 0
15
SCAN
Scan monitors for signals on the transceiver channels. While
scanning, the transceiver checks for a signal on each channel
and only stops if a signal is present.
To begin scanning, press the key programmed as [Scan].
• The icon appears on the display.
• When a signal is detected on a channel, Scan pauses at that
channel. The transceiver will remain on the busy channel until the
signal is no longer present, at which time Scan resumes.
To stop scanning, press the Scan key again.
Note: To use Scan, there must be at least 2 channels in the scan
sequence.
PRIORITY SCAN
Note: To use Priority Scan, a Priority channel must be programmed.
When using a single Priority channel, the transceiver will
automatically change to the Priority channel when a call is
received on that channel, even if a call is being received on a
normal channel.
When using dual Priority channels, Priority channel 1 is given
precedence over Priority channel 2. So, if a call is received on
Priority channel 1 while a call is already on Priority channel 2,
the transceiver will change to Priority channel 1.
16
SCAN REVERT
The Scan Revert channel is the channel selected when you
press the PTT switch to transmit during scan. Your dealer can
program one of the following types of Scan Revert channels:
• Selected: The last channel selected before scan.
• Selected + Talkback: Same as “Selected”, plus you can
respond to calls on the channel at which scan is paused.
• Priority 1/ Priority 2: The Priority channel (either Priority 1
or Priority 2) .
• Priority 1 + Talkback/ Priority2 + Talkback: Same as
“Priority 1/ Priority 2”, plus you can respond to calls on the
channel at which scan is paused.
• Last Called + Selected: The last channel on which you
receive a call.
SCAN DELETE/ADD
You can add and remove zones and/or channels/group IDs to
and from your scan list.
1 Select your desired zone and/or channel/group ID.
2 Press the key programmed as [Zone Delete/Add] (to add/
remove zones) or [Scan Delete/Add] (to add/remove
channels/group IDs).
• You can also press and hold the key programmed as [Scan
Delete/Add] to add/remove zones.
PRIORITY-CHANNEL SELECT
If the Priority channel has been set as Operator Selectable by
your dealer, you can reprogram the Priority channels.
1 Select your desired zone and channel/group ID.
2 Press the key programmed as [Priority-channel Select].
3 Press / to select “NORMAL”, “PRIORITY 1” ( ),
“PRIORITY 2” ( ), or “PRIORITY 1&2” ( ).
4 Press to save the setting and exit.
17
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION
FleetSync is an Alphanumeric 2-way Paging Function, and is a
protocol owned by JVC KENWOOD Corporation.
Note:
◆ This function is available only in analog operation.
18
• Select “ALL” Fleet and “ALL” ID to make a call to all units
(Broadcast call).
• Select “ALL” Fleet and enter an ID number to make a call to the
selected ID in all fleets (Supervisor call).
STATUS MESSAGE
You can send and receive 2-digit Status messages which may
be decided in your talk group. Messages can contain up to 16
alphanumeric characters. Status messages range from 10 to
99 (80 ~ 99 are reserved for special messages).
A maximum of 15 received messages (combined status
messages and short messages) can be stored in the stack
memory of your transceiver.
■ Transmitting
1 Select your desired zone and channel.
2 Press the key programmed as [Status] to enter Status
mode (proceed to step 5) or [Selcall + Status] to enter
Selcall mode (proceed to step 3).
3 Press / to select the station you want to call.
• If Manual Dialing is enabled, you can enter a station ID
by using the DTMF keypad, or by using / . When
using / , cycle through the digits to select a digit,
then press to set the digit and move the cursor to the
right. Repeat this process until the entire ID is entered.
4 Press to enter Status mode.
5 Press / to select the status you want to transmit.
• If Manual Dialing is enabled, you can enter a status ID by
using the DTMF keypad, or by using / (refer to
step 3, above).
6 Press the PTT switch or Side 2 key to initiate the call.
• “<COMPLETE>” appears on the display when the status
has been successfully transmitted.
19
■ Receiving
A calling ID or text message will appear when a Status call
is received. Press any key to return to normal operation.
■ Reviewing Messages in the Stack Memory
1 Press the key programmed as [Stack], or press and hold
the key programmed as [Selcall], [Status], or [Selcall +
Status] to enter Stack mode.
• The last received message is displayed.
2 Press / to select the desired message.
• Message types are identified as follows:
I: Caller ID, S: Status Message, M: Short Message
• Press and hold for 1 second or press to cycle the
display information as follows:
ID Name > Status/Short Message > CH/GID > Time Stamp
3 Press to return to normal operation.
• To delete the selected message, press or #. To confirm
the deletion, press or .
• To delete all messages, press and hold or # for
1 second. To confirm the deletion, press or .
SHORT/LONG MESSAGES
Received short messages are displayed the same as Status
messages and are stored in the same stack memory.
To send short messages, and to send and receive long
messages, you must connect the transceiver to a PC. Ask your
dealer for details.
GPS REPORT
GPS data can be manually transmitted by pressing the key
programmed as [Send the GPS data], or by accessing the
Menu {page 13}. If set up by your dealer, GPS data may be
automatically transmitted at a preset time interval.
• When using the GPS function, you must first connect the VHF/
GPS antenna or UHF/ GPS antenna.
20
5-TONE SIGNALING
5-tone Signaling is enabled or disabled by your dealer. This
function opens the squelch only when the transceiver receives
the 5 tones programmed in your transceiver. Transceivers that
do not transmit the correct tones will not be heard.
SELCALL (SELECTIVE CALLING)
A Selcall is a voice call to a station or group of stations.
■ Transmitting
1 Select your desired zone and channel.
2 Press the key programmed as [Selcall], [Selcall +
Status] or [Selcall + SDM] to enter Selcall mode.
3 Press / to select the station you want to call.
• On keypad models, you can directly enter the station ID.
4 Press the key programmed as [Call 1] to [Call 6] and
begin your conversation.
Note: Additionally, you can also use the keys programmed as
[Digit 1x Down], [Digit 1x Up], [Digit 10x Down], and [Digit 10x
Up] keys to adjust the Selcall number. Digit 1x Up/Down increases/
decreases the Selcall number by 1 each time the key is pressed.
Digit 10x Up/Down increases/decreases the Selcall number by 10
each time the key is pressed.
■ Receiving
When you receive a call containing the correct tones, the
transceiver will enter Selcall mode. An alert tone will sound
and the calling station’s ID appear on the display. Press any
key to return to normal operation.
21
STATUS MESSAGE
You can send and receive Status messages which may be
decided in your talk group. Messages can contain up to 16
alphanumeric characters.
A maximum of 15 received messages can be stored in the
stack memory of your transceiver.
■ Transmitting
1 Select your desired zone and channel.
2 Press the key programmed as [Status] to enter Status
mode (proceed to step 5) or [Selcall + Status] to enter
Selcall mode (proceed to step 3).
3 Press / to select the station you want to call.
• You can enter a station ID by using the DTMF keypad, or
by using / .
4 Press to enter Status mode.
5 Press / to select the status you want to transmit.
• You can enter a status ID by using the DTMF keypad, or by
using / (refer to step 3, above).
6 Press the key programmed as Call 1 to Call 6 to initiate
the call.
■ Receiving
A calling ID or text message will appear when a Status call
is received. Press any key to return to normal operation.
22
■ Reviewing Messages in the Stack Memory
1 Press the key programmed as [Stack] to enter Stack
mode.
• The last received message is displayed.
2 Press / to select the desired message.
• Press and hold for 1 second or press to cycle the
display information as follows:
Selcall Name > Status Name > CH/GID > Time Stamp
3 Press to return to normal operation.
• To delete the selected message, press or #. To confirm
the deletion, press or .
• To delete all messages, press and hold or # for
1 second. To confirm the deletion, press or .
23
ADVANCED OPERATIONS
DTMF (DUAL TONE MULTI FREQUENCY) CALLS
■ Making a DTMF Call Manual Dialing (Keypad Models Only)
1 Press and hold the PTT switch.
2 Enter the desired digits using the DTMF keypad.
• If you release the PTT switch, transmit mode will end even
if the complete number has not been sent.
• If the Keypad Auto PTT function has been enabled by
your dealer, you do not need to press the PTT switch to
transmit; you can make the call simply pressing the DTMF
keys.
Store & Send
1 Press the key programmed as [Autodial].
2 Enter up to 30 digits using the DTMF keypad.
• Alternatively, you can enter digits by using / .
3 Press the PTT switch to make the call.
■ Autodial
Autodial allows you to quickly call DTMF numbers that have
been programmed onto your transceiver.
1 Press the key programmed as [Autodial], or access the
Menu {page 13}.
• The first entry in the Autodial list appears on the display.
2 Press / to select your desired Autodial list
number, or enter the list number directly (01 ~ 32).
• The stored entry appears on the display.
3 Press the PTT switch to make the call.
24
■ Stun Code
This function is used when a transceiver is stolen or lost.
When the transceiver receives a call containing a stun
code, the transceiver becomes disabled. The stun code is
cancelled when the transceiver receives a call with a revive
code.
EMERGENCY CALLS
If your transceiver has been programmed with the Emergency
function, you can make emergency calls.
1 Press and hold the key programmed as [Emergency].
• Ask your dealer for the length of time necessary to hold this
key before the transceiver enters Emergency mode.
• When the transceiver enters Emergency mode, it will change to
the Emergency channel and begin transmitting based on how it
is set up by your dealer.
2 To exit Emergency mode, press the Emergency key again.
• If the Emergency mode completes a preset number of cycles,
Emergency mode will automatically end and the transceiver
will return to the zone and channel that was in use before
Emergency mode was entered.
Note:
◆ Your dealer can set the transceiver to emit a tone when
transmitting in Emergency mode.
◆ Your dealer can set the transceiver to emit tones and received
signals as normal, or mute the speaker during Emergency
operation.
SCRAMBLER
Press the key programmed as [Scrambler/ Encryption], or
access the Menu {page 13}, to switch the transceiver to secure
(encrypted) transmission.
• Pressing the PTT switch after the Scrambler function has been
turned ON encrypts the transmitted signal.
25
SIGNALING
■ Quiet Talk (QT)/ Digital Quiet Talk (DQT)
Your dealer may have programmed QT or DQT signaling on
your transceiver channels. A QT tone/ DQT code is a
sub-audible tone/code which allows you to ignore (not hear)
calls from other parties who are using the same channel.
26
■ Optional Signaling
Your dealer may also program several types of optional
signaling for your transceiver channels.
5-tone Signaling: Refer to “SELCALL (SELECTIVE
CALLING)” {page 21}.
DTMF Signaling : DTMF Signaling opens the squelch only
when the transceiver receives a call containing a matching
DTMF code.
FleetSync Signaling : Refer to “SELCALL (SELECTIVE
CALLING)” {page 21}.
NXDN ID Signaling: NXDN ID is an optional signaling
system available only for digital communications.
27
VOICE OPERATED TRANSMISSION (VOX)
VOX can be activated or deactivated by your dealer. VOX
operation allows you to transmit hands-free.
Note: To operate VOX, you must use an optional KHS-11, KHS-14,
KHS-15-BH, or KHS-15-OH headset.
28
Note: If a speaker/ microphone is connected to the transceiver
while VOX is ON, and the VOX Gain Level is set to a sensitive
level, louder received signals may cause the transceiver to
transmit.
29
BACKGROUND OPERATIONS
Your dealer can activate a variety of transceiver functions to
perform without any additional operation on your part.
CLOCK
If activated by your dealer, you can view the clock by pressing
the key programmed as [Clock].
Note: Removing or leaving the battery pack uncharged for
extended periods will clear the clock time.
To set the clock:
1 Press the key programmed as [Clock Adjustment].
• The current time setting appears.
2 Press / to increase or decrease the year setting.
3 Press to set the year and cycle to the month setting.
4 Repeat steps 2 and 3 to set the month, day, hour, and minute.
5 Press to exit Clock Adjustment mode.
• You can press at any time to exit Clock Adjustment mode.
VIBRATOR
When an optional vibrator is installed, the vibrator function will
alert you when an optional signaling call is received. Press the
key programmed as [Vibrator], or access the Menu {page 13},
to turn the Vibrator function ON and OFF.
TIME-OUT TIMER (TOT)
The Time-out Timer is used to prevent you from using a
channel for an extended duration. If you continuously transmit
for a preset time, the transceiver will stop transmitting and an
alert tone will sound. Release the PTT switch.
30
BATTERY SAVER
The Battery Saver can be activated only on Conventional
channels. This function decreases the amount of power used
when a signal is not being received and no operations are
being performed.
KEY LOCK
Press the key programmed as [Key Lock] to lock and unlock
the transceiver keys.
• The following keys still function when Key Lock is activated:
Emergency, Backlight, Monitor, Monitor Momentary, Squelch Off,
Squelch Off Momentary, Function, Key Lock, PTT
31
COMPANDER
If programmed by your dealer for a channel, the compander will
remove excessive noise from transmitted signals, to provide
higher clarity of signals.
Note: The COMPANDER is used only in analog operation.
PTT ID
PTT ID is the transceiver unique ID code which is sent each
time the PTT switch is pressed and/or released.
Note: PTT ID can be made only in analog operation.
32
VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT
Note: If use the VGS-1 unit, the GPS unit must be removed. Please
ask your dealer.
VOICE RECORDER
The voice recorder allows you to record conversations and
create voice memos.
■ Auto Recording
If activated, the auto recorder will continuously record all
transmitted and received signals. The recording storage
area retains only the last 30 seconds of recording.
■ Voice Memos
To record a voice memo for later playback:
1 Press the key programmed as [Voice Memo], press and
hold the key programmed as [Playback], or access the
Menu {page 13}.
• The duration of recording memory will appear on the
display and begin counting down.
2 Speak into the microphone to record your memo.
3 Press to end the recording and store it in memory.
• If the memory becomes full, recording will stop and the
voice memo will be stored in memory.
■ Auto Reply Message
You can set the transceiver to automatically respond to
Individual Calls while using FleetSync/NXDN.
1 Press the key programmed as [Auto Reply Message]
to enter Auto Reply Message mode.
2 When you receive an Individual Call, the transceiver will
send an automatic response to the caller after
3 seconds, and “GREETING” appears on the display.
33
• If you are available to receive the call, press any key to
cancel the auto response.
• If there is memory available on your transceiver, “I am not
available. Leave your Message.” will be sent to the caller
and they can leave you a recorded message. When a
message is stored on your transceiver, “NEW MESSAGE”
appears on the display.
• If no memory is available on your transceiver, “I am not
available” will be sent to the caller and “MEMORY FULL”
appears on the display.
■ Playback
To play back a recorded conversation, memo, or message:
1 Press the key programmed as [Playback] or access the
Menu {page 13}.
• If the last action on your transceiver was to auto record
your conversation, “STORE?” will appear on the display,
otherwise a recording channel with the time of the
recording will appear.
2 Press / to select the channel you want to play.
• “AR” represents auto recorded conversations, “RM”
represents auto reply messages, and “VM” represents
voice memos.
3 The transceiver will announce the time and channel,
then the recording will play back.
• When the entire recording has been played, “END OF
MESSAGE” is displayed. You can also end the recording at
any time by pressing .
• To delete the selected recording, press . To clear all the
recorded data, press and hold .
VOICE GUIDE
When changing the zone and/or channel, an audio voice will
announce the new zone and channel. Additionally, when
changing a function setting, the new setting will be announced.
Note: Voice announcements vary by dealer setting.
34
© 2016