SNP 1000a Eng

Real-time Network
Dynamic 10X
Pan & Tilt
10X PTZ Network Camera SNP-1000A User’s Manual

Thank you for purchasing a SAMSUNG iPOLiS Network Camera.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
ENGLISH
Preface
A brand that is integrated into Samsung's network products,

stands for a convenient world (Polis) made safe
(Police) through Samsung's superior network performance(Internet
protocol). With products' clear digital images
transmitted over the internet, real-time monitoring is possible
anywhere with an internet connection. Easy remote control
functions and the use of existing networks minimize installation
costs. With , experience a world of convenience
connected anytime, anywhere.
Preface
Thanks for purchasing of 10X PTZ Network Camera SNP-1000A.
This is a user instruction manual for a 10X PTZ Network Camera

SNP-1000A that employs Samsung Techwin’s WINNER Ⅲ DSP
system with superior low light capability.
The user who installs and operates the product shall be aware of this
manual and other manuals referenced by this manual before the
installation and operation and use properly.
This manual and the software and hardware explained here are
protected by copyright law.
So the copy, reprint and translation to other languages of a part of or

all contents of this user manual without permission of
SamsungTechwin Co., LTD are not allowed except for the copy for
general use within the scope of copyright law.
i
Contents
Contents
Preface .............................................................................. i
Contents ...........................................................................1
Note to User .....................................................................5
Product Warranty and Limitations ....................................8
Warning Symbols .............................................................9
Danger..............................................................................9
Caution ........................................................................... 11
Ch1. Overview .......................................................................13
1.1. 10X PTZ Network Camera SNP-1000A Introduction .......14

1.2. Features ..................................................................14
Ch2. Section names and functions .....................................17
2.1. Body ........................................................................18

2.2. Rear panel ...............................................................18
2.3. Connection to external terminal...............................19
Ch3. Installation and Network Setup...................................21
3.1. Components and Accessories.................................22

3.2. Installation ...............................................................23
3.2.1. Preparation for Cable ............................................. 23
3.2.2. Cable Connection................................................... 24
3.2.3. Installation of SNP-1000A ...................................... 26
3.2.4. Installing the SNP-1000A on a Ceiling.................... 27
3.2.5. Installing the SNP-1000A Wall Mount ..................... 29
3.2.6. Installing the Dome Housing (STH-1000PI)............ 31
1
10X PTZ Network Camera SNP-1000A
3.3. Network configuration and connection method .......32

3.3.1. Configuration/connection using Web page ............. 32
Ch4. How to Use Web Viewer...............................................37
4.1. How to Use Web Viewer..........................................38

4.1.1. Login ...................................................................... 38
4.1.2. Web Viewer screen ................................................ 39
4.1.3. Area Zoom guide.................................................... 45
4.2. Using Administration page.......................................49

4.2.1. Initialization Screen after Connecting ..................... 49
4.2.2. Live ........................................................................ 50
4.2.3. Basic ...................................................................... 51
4.2.4. Network.................................................................. 53
4.2.5. User ....................................................................... 54
4.2.6. Pan/Tilt/Zoom......................................................... 57
4.2.7. Motion Detection .................................................... 59
4.2.8. Alarm/Sensor ......................................................... 60
4.2.9. Time ....................................................................... 63
4.2.10. LOG ..................................................................... 64
4.2.11. Upgrade ............................................................... 65
4.2.12. System Reboot..................................................... 66
Ch5. How to Operate Camera...............................................67
5.1. OSD Menu Organization .........................................68

5.2. PTZ Camera User Menu Settings ...........................71
5.2.1. Camera Setting ...................................................... 71
5.2.2. FOCUS .................................................................. 71
5.2.3. White Balance ........................................................ 73
2
Contents
5.2.4. Exposure................................................................ 75
5.2.5. Back Light .............................................................. 76
5.2.6. AGC ....................................................................... 77
5.2.7. SSNR (Samsung Super Noise Reduction) ............. 77
5.2.8. Day & Night............................................................ 78
5.2.9. Others .................................................................... 79
5.3. Sequence Setting ....................................................80

5.3.1 Preset ..................................................................... 80
5.3.2. Swing SEQ............................................................. 82
5.3.3. Group SEQ ............................................................ 83
5.3.4. Tour SEQ ............................................................... 83
5.3.5. PTZ Trace .............................................................. 84
5.3.6. Auto Run ................................................................ 85
5.3.7. Power On Resume................................................. 86
5.4. P/T Setting...............................................................87

5.4.1. Pan Limit ................................................................ 87
5.4.2. Tilt Limit.................................................................. 87
5.4.3. Area Setting ........................................................... 88
5.4.4. Area Masking ......................................................... 89
5.4.5. Prop. P/T................................................................ 89
5.4.6. Digital Flip .............................................................. 90
5.4.7. Jog Speed .............................................................. 90
5.5. OSD Setting ............................................................91

5.5.1. Camera Name........................................................ 91
5.5.2. Preset Number ....................................................... 92
5.5.3. Preset Name .......................................................... 92
5.5.4. Sequence Status .................................................... 93
3
5.5.5. Area Name ............................................................. 93

5.5.6. PTZ Position .......................................................... 94
5.5.7. Language ............................................................... 94
5.6. Initialization Setting .................................................95

5.7. Status.......................................................................96
Ch6. Troubleshooting ...........................................................97
Appendix A. DDNS Usage...................................................101
Specifications ...............................................................109
Dimension .................................................................... 112
If you refer to the enclosed Quick guide and the

Note Manual in the CD, you can learn how to use Network
Manager Standard.
4
Note to User
Note to User
This machine’s electromagnetic waves have been registered as

suitable for business purposes; the retailer and consumer should be
aware of this registration. If in the case of wrongful purchases,
please exchange the product for a home use product.
Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other

European countries with separate collection
systems)
This marking shown on the product or its literature, indicates that it

should not be disposed with other household wastes at the end of its
working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate this
from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources. Household users should
contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can
take this item for environmentally safe recycling. Business users
should contact their supplier and check the terms and conditions of
the purchase contract. This product should not be mixed with other
commercial wastes for disposal.
5
Samsung Techwin cares for the environment at all

product manufacturing stages to preserve the
environment, and is taking a number of steps to
provide customers with more environment-friendly
products.The Eco mark represents Samsung
Techwin s will to create environment-friendly
products, and indicates that the product satisfies
the EU RoHS Directive.
6
Note to User
Correct disposal of batteries in this product
(Applicable in the European Union and other

European countries with separate battery return
systems.)
This marking on the battery, manual or packaging indicates that the

batteries in this product should not be disposed of with other
household waste at the end of their working life. Where marked, the
chemical symbols Hg, Cd or Pb indicate that the battery contains
mercury, cadmium or lead above the reference levels in EC Directive
2006/66. If batteries are not properly disposed of, these substances
can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please

separate batteries from other types of waste and recycle them through
your local, free battery return system
7
Product Warranty and Limitations
The manufacturers of this product do not take any responsibility for

this product; therefore, the manufacturer does not authorize the
third-party, but allows that retailer is responsible.
The product warranty does not extend to cover accidents, negligence,

abuse, or wrongful use for the whole or any part of the product.
Additionally, the manufacturer does not provide warranty for any
additional parts or affiliations.
The warranty is for one year from the purchase date. During the
period, warranty does not extend to malfunction in these areas.
y Malfunction due to user’s negligence

y Dismantlement or replacement by the user
y Connection to alternate power source
y Malfunction due to natural disasters (fire, flood, tsunami, etc.)
y Replacement due to wear and tear
y Instability of network
8
Warning Symbols
Warning Symbols
Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for
future use.
Danger :
Misuse or wrongful operation of the product may
result in death, injury or bring about other fatal
results. It indicates absolute caution when operating.
Caution :
Misuse or wrongful operation of the product may
result in slight injury or damage to the product. It
indicates caution when operating.
Note :
Indication that the user needs to be aware of certain
matters, or will find matters helpful in operating the
product.
Danger
Before Setup
y Please set up the proper voltage before connecting to power
source.
y Please be sure the power is turned off before setup.
9
y There is risk of shock or fire; be sure to avoid setup in places

with high humidity.
y To prevent shocks, please connect the ground wire.
y Do not install the camera on a surface that can not support it.
y Unless the surface is suitable, it could cause falling or other

hazards.
During Use
y When opening the product cover, there is a risk of electric
shock. Only a professional should open the cover.
y Please use only in an environment with standard temperature

and humidity.
y Please do not plug in multiple products to a power source; it is

often the cause of fires.
y Please do not place water or heavy objects on the product; it is

often a cause of malfunction.
y Please do not use in a location with propane gas, gasoline or

other flammable substances to avoid risk of explosion or fire.
y Please do not touch the power plug with wet hands to avoid
electric shock.
y Do not pull on the power plug with too much force; a damaged
plug may cause electric shock or fires.
y Don’t connect the RJ-45 cable to a terminal by constraint.
y Stop using your camera when you find a malfunction.

If you use your camera around smoke or unusual heat for a
long time, Fire may be caused.
10
Caution
y Random replacement of built-in battery by other types of

batteries may cause explosion. The battery shall be replaced by
the same battery. The lithium battery incorporated in this
product is not user replaceable. Replacement of the lithium
battery will be done by a trained technician.
For information on its replacement, please contact your service
provider.
y The used batteries shall be disposed carefully because they can

cause environment pollutions.
Disassembly and Cleaning

y There is a risk of malfunction, shock or other dangers. Please
do not disassemble or attempt to fix the product.
y To prevent malfunction or shock, please do not use a wet cloth

or oil-based cleaning product to clean the product exterior.
Clean the exterior of the product with a dry cloth.
Caution
y Do not install under extreme temperature conditions

Use only under temperature conditions between -0°C and
+40°C. Provide good ventilation when using in high
temperature conditions.
11
y Do not install under unstable lighting conditions.

Severe lighting changes or flickering may hinder normal
camera operation.
y Do not drop the camera or subject it to physical shock.

May cause a product malfunction.
y Never keep the camera face to strong light directly.

May damage the CCD.
y Avoid touching the camera lens.

The lens is the most important component of the camera. Be
careful not to smear it with fingerprints.
y Do not expose the camera to rain or other types of liquids

Wipe dry any liquids. Liquids may contain minerals that are
corrosive to Electronic components.
y Do not expose the camera to radioactivity.

Radioactivity exposure may damage the CCD.
y Do not disassemble the camera.

If you disassemble the product as you please, a Repair Center
doesn’t repair it for free.
y Please check the created network place first, before trying to

connect to a network.
y Please use only the power adapter that is provided with the
product.
y Please check national laws to be sure that using the product for
monitoring purposes is not illegal.
12
C h 1. O v e r v ie w
1.1. 10X PTZ Network Camera SNP-1000A Introduction
The SNP-1000A is a high-tech network camera that uses MPEG-4

codec technology to allow high compression rates and clear picture
quality by allowing for high frame rates to be transmitted through
the network.
By using the network, remote connection, monitoring, and control is

possible from any location for simple use; additionally, set-up
requires only a network.
The 10X PTZ Network Camera SNP-1000A utilizes embedded

software solutions (Embedded Web Server, Embedded Streaming
Server, Network Protocol) developed by SamsungTechwin, and
guarantees performance and safety while offering various solutions
through Internet integration.
1.2. Features
10X Zoom Lens with Auto-Focus Function

The 10X zoom lens having Auto-focus function magnifies
the image up to 100 times when used with the digital 10X
zoom function.
Variable Auto Surveillances

• Individual Preset Saving Modes
12 camera adjustment functions can be saved independently
in each Preset menu to provide optimum images.
• PTZ Trace
4 patterns which are set up by users can be saved and replayed.
14
1.2. Features
• Auto Swing
Pan or Tilt is operated in sequence between 2designated
positions.
• Group Search
Maximum 128 Preset positions are toured in order.
• Tour Search
Maximum 6 Group Search functions are toured in order.
Proportional P/T
Even when the Zoom-In function is On for the Pan and Tilt
speed correction function linked to the zoom position, fine
manual operation is possible.functions are toured in order.
Day & Night

Day & Night function of ICR (IR Cut-Filter Removal) and
Sens-Up function can achieve optimum images during
day and night.
※ Sens-Up function improves the CCD sensitivity by lengthening
the exposure time using electricity.
※ Day&Night function enables users to select and adjust the colour
and black and white images according to the light level.ions are
toured in order.
OSD (On Screen Display)

Items such as Camera ID, Camera Name, Preset Number,
Preset Name, Area Name and Camera Status are
displayed on the monitor. Camera functions can be set up
on the OSD menu screen.
15
128 Preset Position

A maximum of 128 Preset positions can be set up. This
function enables users to set up the monitoring place any
time.
Digital Flip
When you want to monitor the moving object below the
camera, you can execute the Digital Flip. The moving
object can be monitored without screen reverse.
Area Masking
For privacy protection, a maximum of 4 areas can be
masked among the surveillance areas preventing them to
be displayed on the screen.
High Data Compression Ratio

Its data transfer speed is very fast with high data
compression ratio based on MPEG-4 and it transfers
relatively high frame number at the same network
bandwidth.
Area Zoom
This zooming function supports image expansion of
square area by mouse dragging.
Function execution is easy only with mouse operation.
Just one time clicking completes PTZ position adjustment

at Area Zoom mode.
16
C h 2. S e c t io n n a m e s a n d f u n c t io n s
2.1. Body
2.2. Rear panel
① Power Connector
② Audio Input Connector
③ Audio Output Connector
④ Alarm Input/Output Connector
⑤ Network Connector
18
2.3. Connection to external terminal
2.3. Connection to external terminal
19
Alarm Connection Terminal
PIN NO. NAME Purpose

#1 - Not Used.
#2 - Not Used.
#3 - Not Used.
#4 S1 Alarm Input 1
#5 S2 Alarm Input 2
#6 G GND
#7 +V DC 12V
#8 NO Alarm Output(NO)
#9 NC Alarm Output(NC)
#10 CM Alarm Output(COM)
20
C h 3. Installation and Network Setup
3.1. Components and Accessories
Accessories
Products Sold Separately

The following products are provided separately.
y Accessory Housing
- Wall Type Mount : STB-280PW
- Wall Type Mount : STB-230PW
- Dome Housing : STH-1000PI
See pages 26 for product images.

Note
22
3.2. Installation
3.2. Installation
3.2.1. Preparation for Cable

To install and use the SNP-1000A, the following cables should be
used.
y Power Adapter Cable
The cable connected to the power input terminal of SNP-

1000A is shown below with a rated voltage of DC 12V 4A.
y Video Cable
The BNC cable shown below is connected to the video output

terminal and the monitor of SNP-1000A.
23
y Lan Network Cable
The cable connected to the network device of SNP-1000A for

Network communication is shown below.
Video cable and LAN network cable are not

provided in this product’s package.
Note
BNC connection terminal can optionally be used to
connect when the Analog output is necessary.
3.2.2. Cable Connection

1. First, connect one end of the BNC video cable connector to the
Video Output Terminal.
2. Next, connect the other end of the connector to the Video Input
Terminal of the monitor.
24
3.2. Installation
3. For the network connection of the SNP-1000A, connect the

LAN Cable as the figure below shows.
4. Then, connect the Power Adapter Cable. Use a driver (-) to

screw one part of the Power Adapter consisting of two lines to
the Power Input Terminal of the camera holder.
5. Connect the Power Adapter’s plug to the Power Outlet.
25
3.2.3. Installation of SNP-1000A
Precautions for Installation

Check that the installation location can safely bear four times the
weight of the camera and its installation fittings.
When fixing the ceiling installation bracket, use the supplied
installation template and fixing screws.
Take care not to drop the product during installation. Do not allow
anyone to stand below the installation area.
Optional Products for Installation
y Wall Mount (STB-280PW)
This housing is used to install

the camera on an indoor wall or
ceiling using an external
conduit.
y Wall Mount(STB-230PW)
This housing is used to install

the camera on an indoor wall.
y Dome Housing (STH-1000PI)
This housing is used to install the camera

in a location that is dusty, or a place
where extra protection for the camera is
required.
26
3.2. Installation
3.2.4. Installing the SNP-1000A on a Ceiling

1. Prepare the accessories in the camera box (power adapter,
installation template, audio extension cable, 1 loose-proof screw,
3 installation bracket fixing screws, 2 installation brackets,
installation cover, installation CD) and a tool for making a hole
in the ceiling.
2. Attach the installation template to

the ceiling where you want to
install the camera, make a hole of at
least 65mm in diameter, and 3 holes
for fixing screws according to the
marks on the template, and pull the
external incoming cables out of the
hole.
Precautions before Attaching the Installation

Template
Caution Installation Location: Check that the function
and performance of the camera installed on
the ceiling will not be adversely affected by the
external environment, and that the ceiling can
adequately support the weight of the camera.
Installation Direction: Determine the main
direction of the camera in advance and attach
27
the template so that the front of the template is

in line with the camera direction.
Caution: Since there is a danger of the product
falling during installation, take care not to allow
3. Align the arrow on the ceiling

attachment installation bracket
with the front of the template,
fix the bracket by fastening the 3
screws through the holes, and
connect the external incoming
cables (video cable, network
cable and power cord) to the
camera.
4. Assemble the camera, which

should already have been
attached to the product
installation bracket, to the
ceiling attachment installation
bracket, facing forwards, and fix
the camera with the supplied
fixing screw.
5. To complete installation,
rotate the installation
cover along the groove of
the ceiling attachment
bracket, and fix it.
28
3.2. Installation
3.2.5. Installing the SNP-1000A Wall Mount

1. Prepare the accessories in the camera box (power adapter, audio
extension cable, 2 installation brackets, 1 loose-proof screw,
installation CD, installation cover) and the wall mount(STB-
280PW or STB-230PW) and 3 installation bracket fixing
screws in the mount packaging box.
2. Fix the wall mount (STB-280PW) with 3

screws to the wall where the camera is to be
installed, as shown in the figure on the right.
Precautions before Attaching the Installation

Template
Caution Precautions before Attaching the Installation
Template
Installation Place: Check that the function and
performance of the camera installed on the
wall will not be adversely affected by the
external environment, and that the ceiling can
adequately support the weight of the camera.
Installation Direction: Determine the main
direction of the camera in advance and attach
29
the template so that the front of the template is

in line with the camera direction.
Caution: Since there is a danger of the product
falling during installation, take care not to allow
3. Fix the wall bracket and the wall surface attachment installation
bracket onto the wall mount (STB-280PW) with the screws
supplied, as shown in the figure on the right, and connect the
external incoming cables (video cable, network cable and
power cord) to the camera.
4. Assemble the camera, which should already have been attached

to the product installation bracket, to the wall attachment
installation bracket, facing forwards, and fix the camera with
the supplied fixing screw.
30
3.2. Installation
5. To complete installation, rotate the installation cover along the

groove of the ceiling attachment bracket, and fix it.
3.2.6. Installing the Dome Housing (STH-1000PI)

To install the Dome Housing (STH-1000PI), fix it instead of
installing the cover in the last step “3.2.4. Installing the SNP-1000A
on a Ceiling” on page 27 and “3.2.5. Installing the SNP-1000A Wall
Mount” on page 29.
When the Dome Housing is When the Dome Housing is
installed on the ceiling installed on the wall
31
3.3. Network configuration and connection method
3.3.1. Configuration/connection using Web page

Use when there is one 10X PTZ Network Camera SNP-1000A to be
installed.
1. Please connect user’s PC to 10X PTZ Network Camera SNP-
1000A using cross cable.
2. To configure network, the internal IP must be registered in the

user’s PC.
32
3. After pressing internet protocol (TCP/IP) properties, press the

‘advanced’ button to go into advanced configurations.
4. The IP address of IP setting tap can be added as

"192.168.1.XXX"
"XXX" is an IP address voluntarily set by a customer.
5. Please launch a Web browser on user’s PC and enter
[192.168.1.100] in the URL address field and push <Enter>
button. Connect to Webviewer login window of 10X PTZ
Network Camera SNP-1000A.
6. Please login with administrator’s authorization and move to

‘Setup-Network’ page.
33
Default value is ID : admin, PW : 11111111

Note
7. Please configure according to the network environment where

10X PTZ Network Camera SNP-1000A will be installed and
push <Save> button to save the configuration.
34
① LAN / xDSL/ DHCP Configuration
Item Description
When network product is connected to normal
LAN Use local LAN or when connected to static IP, the
network data to be allotted to the IP is configured.
When using xDSL dynamic IP, enter the ID and
xDSL
PW.
When automatically receiving IP through DHCP
server, the DHCP functions are activated.
Video Quality ‘DHCP’ is used in the LAN environment where the
DHCP is activated. Generally, for mid/large scale,
DHCP servers are operated through LAN and for
small-scales, IP sharers use DHCP functions.
② Port Configuration
Item Description
The connection port and http, ftp port
Port Setting configurations can be set here and the DDNS use
can be checked.
35
Use SWR changes its IP address every time the user

attempts to connect to the ISP and when the product
Note is connected to a cable modem or xDSL modem. In
this case, the user cannot know the changed IP
address. When a product that uses dynamic IP is
registered on the DDNS server, when wishing to
connect to the product, the changed IP address can
be easily recognized. In order to register the IP
address to the DDNS server, set Use SWR as
Enabled.
36
C h 4. How to Use Web Viewer
4.1. How to Use Web Viewer
4.1.1. Login
To connect to the login page, click the ‘move to Webpage’ button on
Network Manager or enter network camera IP address on the
internet web browser and press the enter key.
Enter user ID and password and push <Login> button, it then moves
to the appropriate Web page.
Default value is ID: admin, PW: 11111111

Note
If you click <Guest> button, it moves to WebViewer page under the

Guest authenticated status. However, administrator has to permit
guest access for this.
If you logged in first in administrator mode, please

change the password of administrator. It can
Note prevent other users from connecting to the
administration page.
38
4.1.2. Web Viewer screen

Web Viewer screen is composed of menu area for camera/video
configuration and screen area for displaying input video from
camera.
Controls
Flip Image
Vertical reversal of channel screen
39
Stretch Image
When selecting resolution with Half D1 and CIF, stretches
channel screen to resolution D1 size.
Save Image
Saves channel screen to ‘JPEG file’.
Quad
Converts to 4 split screens (applied only to 4 channel server).
Compression
Video compression mode (the mode of
compressing video)
- MPEG, JPEG
Resolution
Video resolution (the size of video screen
transmitted)
- NTSC : D1(704x480), Half D1(704x240),
CIF(352x240)
- PAL : D1(704x576), Half D1(704x288),
CIF(352x288)
Frame Rate
The number of maximum video frame
transmitted for each second.
- 1, 5, 10, 15, 20, 25, 30
Quality
Quality Configures video quality
- Very High, High, Normal, Low, Very Low
40
Pause Stops video for a while.
OSD Displays related information.
Displays the title
Removes the title
41
Deinterlace On/off function of Deinterlace.
Screen where
Deinterlace is not
applied
Screen where
Deinterlace is not
applied
Deinterlace is a function to adjust the video quality

Note softly by eliminating the border line which was made
by an interlace function. The interlace function draws
an even line and an odd line of the Image one after
the other.
42
Camera Setup Displays OSD control button of camera.
Camera OSD
control button is
displayed
Camera OSD is
displayed
Day&Night configuration function

Day&Night
(Color, B/W configuration)
PTZ Control PTZ control function
Screen where
camera PTZ
control window is
displayed
43
The left/right slide bar can control focus (left slide

bar) / zoom (right slide bar)
Note
The “+” displayed in the middle can be pressed
using the mouse as the base point of the Pan / Tilt
and it will Pan /Tilt according to that point.
Instruction for Camera OSD control button
<↑>, <↓> button

Moves selection displaying arrows up and down on
camera OSD menu.
<←>, <→> button

Changes configuration of selected field on camera OSD
menu.
<Set> button
Displays camera OSD or moves to upper/lower menu of
selected field.
<Exit> button
Terminates camera OSD.
※ For configuring the function and detail operating method of 10X
PTZ Network Camera SNP-1000A, refer ‘Ch5. How to Operate
Camera’.
44
4.1.3. Area Zoom guide

Area Zoom function supports easy and fast PTZ (Pan/Tilt/Zoom)
control for the selected image area on the monitor.
Screen image of menu popped up by clicking mouse right button
Clicking mouse right button delivers menu of Area Zoom function.
Screen image of Area Zoom pointer appeared by Area Zoom selection
Clicking Area Zoom menu delivers Area Zoom mode showing yellow colored
Area Zoom pointer at the center of monitor.
45
Screen image of new PTZ position moved by one time click.
Clicking mouse left button only controls PTZ position at Area Zoom mode.
Screen image of selected image area in the mouse dragged square
Clicking mouse left button and dragging a square shapes selected image area
on the monitor.
46
Screen image of expanded area
Releasing mouse left button stimulates automatic PTZ function mode at the
selected image area.
At automatic PTZ function mode, Area Zoom pointer is enlarged and PTZ
function execution is not available.
Screen image of selected Move PTZ on menu
At the Move PTZ zone of menu popped up by clicking mouse right button, reset
function to 1x zoom, previous PTZ position, next PTZ position is available.
PTZ operation at Area Zoom mode stores five positions of before and after the
position change and deactivates Move PTZ zone of menu popped up by
clicking mouse right button.
47
Storage item Function

Go to 1x Zoom Move to 1x Zoom from present PTZ position
Previous PTZ Move to previous PTZ position
Forward PTZ Move to next PTZ position
48
4.2. Using Administration page
4.2.1. Initialization Screen after Connecting
When connection is successful, the below screen will be displayed.
49
4.2.2. Live
Please Move to Web Viewer page
[Web Viewer live screen]
50
4.2.3. Basic
Configures basic information for camera.
Video/Audio Setup
Item Description
Video compression mode
Compression
(Compression mode of video in the camera)
If the type of installed camera (NTSC/PAL) is
Video Size selected, then the size of screen on the
camera becomes selectable.
Selects the quality of video screen. In case of
Video Quality low speed internet, lower the video quality to
see seamless video.
Configures the number of transmitted frame
Video FrameRate
per second in the camera.
51
Item Description
Selects the video channel to be used in the
Video Channel
camera.
Selects whether to use the audio input
Audio-In Channel
channel in the camera or not.
Selects whether to use the audio output in the
Audio-Out Channel
camera or not.
Configures the number of users who can be
Max User Count connected to the camera through the
network(1~20 persons)
Audio amplifying function
onfigures Low for the microphone which has
Mic. Sensitivity amplifying function and High for the
microphone which has no amplifying function.
(In case of Line-In signal, configure Low)
Product Information
Item Description
Model Displays model name of the camera.
Mac Address Displays MAC Address of the camera.
onfigures name of the camera, it help to classify
Camera Name
several cameras.
The location of the installed camera can be
Location
entered.
Additional description related to the camera can be
Description
entered.
The contact of camera administrator can be
Memo
entered.
52
4.2.4. Network
Configures network information of the camera.
Network Configuration
According to the user’s network environment, it is classified into

LAN, xDSL, DHCP.
Item Description
In case the camera is connected to the local
LAN network or xDSL with a static IP address, configure
network information to be assigned to the camera.
In case of xDSL with a dynamic IP address, enter
xDSL
password in UserName and Password field.
This case is selected in case of using IP sharing
DHCP
box/ cable modem.
53
Port/DDNS Configuration
Item Description
Connection This controls communication with camera.
Port (Default : 4000)
HTTP Port/ This helps to connect to web page or FTP server.
FTP Port (Default : http=80, ftp=21)
Select if use of SWR function is available. The way
Use SWR
of connection which used ID does not support.
Select if DDNS server is available. DDNS server is
connected to server without reference to changed
Use DDNS
IP because there is possibility that floating IP
constantly is changed.
※ A detailed explanation about DDNS usage refers to
<Appendix A. DDNS Usage>.
4.2.5. User
This describes password change for administrator or user
registration.
54
Item Description
Administrator
Change password of administrator
Password Change
User clicks ‘Guest’ button to decide whether
Guest Setup
allowing guest to connect Main Viewer.
You can register new user or delete, and set up
Current User
user’s authority.
※ Set up user authority
User’s authorities set up at ‘Current User’ are as follows.

Item Description
Use video related setup function
Video
(Compression, Resolution, Framerate, Quality)
Control Pan, Tilt, Zoom, Audio output, Alarm output
Audio Audio Input
Whether relevant account is used
USE
(If not checked, not allowed log-in)
55
Example 1) In case control function is limited (Do not check

Controls box)
※ Pan, tilt, zoom, audio output, alarm output function icon is

inactivated
Example 2) In case video function is limited (Do not check Video)
※ Compression, Resolution, Framerate, Quality set up icon is

inactivated.
56
4.2.6. Pan/Tilt/Zoom
Configures PTZ Swing and Preset of the camera.
57
Item Description
Channel Select the channel of camera.
PTZ Display Display PTZ menu.
OSD Display Display OSD.
PTZ Set or delete(delete, delete all) the
Camera Preset Preset. Screen move the position of
Configura Preset.
tion
Surveille Pan/Tilt Swing at the position
Swing
of preset, set up the swing menu.
Surveille repeatedly at the position of
Group
preset, set up the Group menu.
Indicate the first position of surveillant
First Setup
Preset
Indicate the second position of
Swing Second Setup
surveillant Preset
Setup
Mode Select Pan/Tilt Mode.
Speed Set Swing speed between Presets.
Duration Set interval time on Preset.
Group No. Set Group Number among 1~6
Group Preset No. Set Preset included the Group.
Setup Travel Speed Set swing Speed between preset.
Dwell Time Set interval time on Preset.
58
4.2.7. Motion Detection

This sets up motion detection function of camera.
Item Description
Basic grid, used to choose area on the screen, is
Grid Display
displayed or hidden.
When selecting motion detection area, click <Select
Select Area All> button to select all areas, or click <Deselect>
button to cancel the selected area.
MD Enable Decide whether you use motion detection function.
Setting up sensitivity to detect motion to adjust input
MD Sensitivity video by situation. You can select 1-5, and 5 is the
highest.
59
4.2.8. Alarm/Sensor
This sets up necessary information when using alarm function by
attaching sensor to camera.
60
Alarm/Sensor Setup
◊ Digital In Setup
Item Description
Types of sensors are ‘Normal open’ and ‘Normal
Sensor Type
close.’ This selects up type of connected sensor.
◊ Digital Out Setup

Item Description
Set up Alarm Out responding when event is
Alarm recognized by connected sensor (Sensor 1) or
Motion Detection (MD)
Set up time to operate relay. It means the period
Duration from the time when sensor detects event to the
time when relay is released.
In case event occurs by sensor (Sensor 1) or
FTP Motion Detection (MD) on the screen, decide
whether transferring related information to FTP.
In case event occurs by sensor (Sensor 1) or
E-mail Motion Detection (MD) on the screen, decide
whether transferring related information by e-mail.
E-mail/FTP Setup
Set up FTP server and e-mail information to which related

information is transferred in case alarm occurs.
Item Description
Mode Select media for data transfer.
Enter domain or IP address of FTP
Server Name
server.
Set up home directory to save relevant
FTP Home Directory
data at FTP server.
User ID Enter ID to connect FTP server.
User Password Enter PW to connect FTP server.
61
Item Description
Recipient E-mail
Address 1 You can designate up to two e-mail
address receiving data when alarm
Recipient E-mail
occurs.
Address 2
In case you use outside e-mail server,
Server Name enter the name of the outside e-mail
server.
E-mail Enter ID to connect the outside e-mail
ID
server.
Enter PW to connect the outside e-
Password
mail server.
Enter the subject of mail to be
Mail Subject
transferred.
Enter the body of mail to be
Mail Body
transferred.
If motion is detected, the contents transferred by e-

mail or to FTP are varied according to the set-up of
Note ‘Video Compression’ at Admin page (Basic).
MPEG : Video length is set by ‘Duration’ of ‘Digital
Out Setup’.
File extension is ‘ste’, you can play this by ‘SLiM
Player’.
JPEG : JPG type image file attached.
62
4.2.9. Time
Current Time
Item Description
Date Current setup date displayed
Time Current setup time displayed
Time Setup
Item Description
Set Manually Adjust time manually.
Time Server Set up address of time server for Server 1 - 5.
63
4.2.10. LOG
Recent activities made for camera are displayed as log.
Item Description
Lines Set up number of lines of the list.
Log is viewed with number of lines you set up most
View
recently.
Clear Delete logs.
64
4.2.11. Upgrade
Upgrade program of 10X PTZ Network Camera SNP-1000A.
System Upgrade Configuration.
Item Description
Upgrade firmware and Web-page of 10X PTZ
Firmware/Web
Network Camera SNP-1000A.
Factory Mode Setup
If you click <Reset> button, server is returned to initial value when

shipped from the factory after confirmation procedure by
administrator.
65
4.2.12. System Reboot

System is rebooted after confirmation procedure of administrator.
Click <OK> button to reboot System.
66
C h 5. H o w t o O p erat e C am era
5.1. OSD Menu Organization
PTZ camera can be set up on the OSD (On Screen Display) menu
displayed on the video monitor.
① Camera Setting
P1 P2 P3 P4 Defaults
Auto/Manual/ OneShot
①Focus Mode
One Shot AF AF
①Focus Mode: On/Off ON
②Zoom Tracking
Speed: Slow/Fast Fast
➌Digital Zoom Off(2X~10X) OFF
ATW/AWC/MANUAL ATW(O)
►ATW
-ATW(I): Indoor
➋White AWB Mode -ATW(O): Outdoor
Balance
►Manual
-Red 29
-Blue 41
➊Brightness 25 025
Auto Auto
➋Iris
Manual: Iris Level 100
--- ESC
A.FLK
③Exposure ➌Shutter Manual: 1/60
1/60~1/120,000,
x2~x128
Auto: Sens-Up Limit X4
➍Sens-Up x1~x128
Off
➍Back Light High/Middle/Low/Off OFF
➎AGC High/Normal/Off Normal
➏SSNR High/Middle/Low/Off Low
Auto
➐Day &
B/W
Night
Color Burst Level 060
➊Sync Internal
Sharpness 008
⑧Others ➋Image Adj.
Color 050
➌Freeze On/Off OFF
68
5.1. OSD Menu Organization
② Sequence Setting
①Preset ①Setting ②Edit ③Execute ④Clear ⑤Status
①Pan Swing ①Setting ②Execute ③Clear
②Swing
②Tilt Swing ①Setting ②Execute ③Clear
SEQ
③P&T Swing ①Setting ②Execute ③Clear
①Group1 ①Setting ②Execute ③Clear
②Group2 ①Setting ②Execute ③Clear
③Group ③Group3 ①Setting ②Execute ③Clear
SEQ ④Group4 ①Setting ②Execute ③Clear
⑤Group5 ①Setting ②Execute ③Clear
⑥Group6 ①Setting ②Execute ③Clear
④Tour SEQ ①Setting ②Execute ③Clear
①Trace1 ①Replay ②Memorize
⑤PTZ ②Trace2 ①Replay ②Memorize
Trace ③Trace3 ①Replay ②Memorize
④Trace4 ①Replay ②Memorize
➊Off OFF
➋Preset: Preset No
③Swing: Swing Mode
Pan/Tilt/P&T
①Mode
➍Group: Group No
⑥Auto Run ➎Tour
➏Trace: Trace1~Trace4
⑦A.Pan
- ①Auto Pan Speed: 20~50 32
- ②Tilt Angle: 10~45 25
➋Time 5,10,20,30(Sec), 1,2(Min) 30sec
⑦Power On OFF
On/Off
Resume
③ P/T Setting
①Pan Limit ➊Position ➋ON/OFF
②Tilt Limit ➊Position ➋ON/OFF
①Area1 ➊Area Name
②Area2 ➋Position
③Area Setting
③Area3 ➌ON/OFF
④Area4
①Mask1 ➊Position
④Area ②Mask2 ➋ON/OFF
Masking ③Mask3
④Mask4
➎Prop.P/T ON/OFF ON
➏Digital Flip ON/OFF ON
⑦Jog Speed Manual(10,20,30,40,50,60) Manual
69
④ OSD Setting
①Camera Name ①ON/OFF ②Edit ➊Position
➋Preset Number ON/OFF ➋ON/OFF ON
③Preset Name ①ON/OFF ②Edit
➍Sequence Status ON/OFF ON
➎Area Name ON/OFF OFF
➏PTZ Position ON/OFF OFF
English, 中文, English
➐Language Francais, Deutsch,
Espanol, Italiano
⑤ Initialize
①Power On Reset ➊Cancel ➋Execute
➋Initial Position ➊Position ➋ON/OFF
③Factory Default Set ➊Cancel ➋Execute
④Camera Default Set ➊Cancel ➋Execute
➎Auto Refresh OFF, 1~7Days OFF
➏ Status
Preset setting is only possible within the OSD menu.

Note
Symbol Description
Note When there are sub menus under the selected
OSD menu.
Numbers are displayed in white color like ① on
the right top of the screen.
When there is no sub menu under the selected
OSD menu.
Numbers are displayed in black color like ➊ on
the right top of the screen.
70
5.2. PTZ Camera User Menu Settings
Execution of OSD Menu : After checking if the camera is in manual

operation mode, press the OSD Menu key. The following commands
are displayed on the monitor screen.
Main Menu
The selection key moves up and
down. Press the execution key
switch on the selected menu to
change the setup menu. Press the
ESC key to exit the OSD Menu.
5.2.1. Camera Setting

Select the Camera Setting on the Main Menu screen to control
camera settings
5.2.2. FOCUS
In Focus menu, you can set up the focus mode among Auto, Manual
or One Shot AF.
71
➊Focus Mode
Auto : The camera adjusts the focus automatically while
monitoring the screen continuously in the auto mode. In the auto
focusing mode, zoom key operation is not recognized as the
input of the focus key.
Manual : In the manual mode, users can adjust the camera focus
manually.
One Shot AF : Only when the camera does not move, it turns into
the auto mode. It is the same as the manual mode.
②Zoom Tracking
Mode: When you select ON, the Focus function is executed when
the Zoom functionis on. When you select OFF, the Focus function
is not executed even when the Zoom function is on.
Speed: Fast will speed up the Zoom. Slow will slow down the
Zoom.
➌Digital Zoom
Magnification of the Digital Zoom can be selected among Off,
2X~10X.
※ It is recommended that the Digital Zoom should be set up before
the preset operation.
Digital Zoom
As the digital zoom magnification increases, the
Caution image quality is lowered.
Auto-focus
Auto-focus may not function normally under the
following conditions.
- When the light level in the surveillance area
is low
- When the slow-shutter works
- When the amplification is increased
- When the light level in the surveillance area
is excessively high
72
- When the objects in the long and short

distance are under the same surveillance
area
- When there is no contrast (white and black)
in the object (e.g. sky or wall)
- When the thin horizontal line is captured
5.2.3. White Balance

The White Balance function corrects the abnormal white colour into
the normal white colour under any colour temperature lighting.
Select the mode among ATW, AWC and Manual. ATW is selected
by default.
WB Mode
ATW
Balances the colour automatically depending on the source of
light from 1,800~10,500K colour temperature.
- Indoor[ATW(I)] : Use this mode in the area under the limited
colour temperature.
- Outdoor[ATW(O)] : Use this mode in the area under the broad
colour temperature.
73
AWC:
Set up the lighting to the objects and corrects the right colour
temperature to that of a white object. Camera works under the
setup conditions. For the most appropriate condition under the
current illumination, capture the white paper and then change the
mode into AWC. Press the Enter key and then AWC Start will be
displayed. When the adjustment is completed after pressing the
Enter key for AWC Start, go to the upper menu. When conditions
change, adjust the white balance function again.
Manual
Fine tuning is possible through this manual control mode. Select
the colour temperature and increase or decrease the Red or Blue
values to shift the colour of the object.
- Red : Red Gain can be changed.

- Blue : Blue Gain can be changed.
White Balance may not function properly under the

Note following conditions.
When the colour temperature surrounding the

object is very high. (e.g. clear sky, sunset)
When it is dark around the object.
When the camera is pointing towards a fluorescent
lamp directly or when lighting conditions change a
lot.
74
5.2.4. Exposure
Camera exposure can be controlled.
➊Brightness
The brightness of the screen can be adjusted.
➋Iris
Auto mode or manual mode can be selected.
Auto: The brightness of the image signal can be adjusted

automatically depending on the amount of light.
Manual: The brightness of the image can be adjusted.
➌Shutter
---: Electronic shutter mode is enabled. The shutter speed is
controlled automatically according to the brightness of the screen.
A.FLK: Use this mode when the screen flickers because of
inconsistent frequency with the surrounding lights.
Manual
- Shutter speed can be controlled manually.
- Shutter speed can be adjusted from 1/60(1/50) second to
1/120,000 second.
- Sens-Up function can be operated manually from x2 ~ x128.
If the Shutter mode is ESC in the inner

synchronization mode and the camera faces to the
Note bright fluorescent lamp directly, the image may be
unstable. Be careful to select the installation
location.
75
If the Manual or A.FLK mode is selected for the

Shutter menu, the Sens-Up function is disabled.
➍Sens-Up
Auto: The low light level of the night or dark condition is detected
automatically and the bright and clear image can be maintained.
- Sens-Up Limit: Maximum accumulated magnification can be
selected.
Off: Sens-Up function is cancelled.
As the accumulated magnification increases, the

screen goes bright. But, the after image of the
Note moving object also becomes larger and the optimum
Auto Focus function may not work.
5.2.5. Back Light

Unlike other cameras, Samsung Techwin’s unique W-III DSP chip
gives you a clear image of the subject even with bright backlight.
HIGH : Gain increased from 6dB up to 34dB.

MIDDLE : Gain increased from 6dB up to 30dB.
LOW : Gain increased from 6dB up to 18dB
OFF : BLC function is cancelled.
76
5.2.6. AGC
When the brightness of the image taken under dark light is under a
certain level, the AGC (Automatic Gain Control) functions to define
whether to control the Gain automatically or not.
HIGH : Gain increased from 6dB up to 34dB.

NORMAL : Gain increased from 6dB up to 18dB.
OFF : Gain is fixed at 6dB.
5.2.7. SSNR (Samsung Super Noise Reduction)

SSNR function reduces background noise under low light conditions
differently in different modes. The noise reduction effect grows in
Off, Low, Middle and High modes in order.
OFF : No noise reduction effect.

LOW : Noise reduction effect is small but there is little afterimage.
MIDDLE: Noise reduction effect is generally effective in this mode.
Noise can be reduced properly and the afterimage is not strong.
77
HIGH : Noise reduction effect is excellent but afterimage is also

strong.
When you select the AGC mode as “OFF”, you

Note cannot use the SSNR function.
5.2.8. Day & Night

The darkness level is detected automatically under low light
conditions such as at night or under dark light to keep the screen
bright and clear.
COLOR : Output images are displayed in colour all the time.

Burst signal size can be adjusted.
B/W : Output images are displayed in black and white all the time.
Burst signal can be kept or removed.
78
AUTO : Under day condition, the mode is automatically changed

into the COLOR mode to keep an optimum colour. At night, the
mode is automatically changed into the B/W mode to distinguish
dark images clearly.
If the AGC is in OFF mode, the Auto mode cannot

be used. Only COLOUR or B/W mode can be used.
Note
If the sunlight or halogen lamp is used in B/W mode,
the focus may be blurred compared with the general
illumination.
5.2.9. Others
①Sync
Internal Sync is selected by default.
Internal : Internal synchronization
➋Image Adj.
Clarity of the video signal and saturation of the color may be
adjusted.
Sharpness : The overall sharpness of the image can be adjusted.

Color : The overall colour density of the image can be adjusted.
➌Freeze
Moving image can be stopped and replayed.
ON : Image can be frozen.

OFF : Frozen image is released and the film is replayed.
79
5.3. Sequence Setting

Sequence Setting Menu
5.3.1 Preset
12 items such as Pan/Tilt location, Zoom and Focus are selected
among camera functions and they can be called for monitoring.
Total 128 points can be preset.
Setting : Select the Preset number for setup. Adjust
Pan/Tilt/Zoom and press the Enter key to save the setting. If you
want to change the 12 items such as Focus, Brightness, Iris and
Scene Adj., use the Up/Down key to go to and select the item. If
you don’t want to change the 12 items, press the ESC key to go
to the next Preset step.
Edit : You can edit the 12 preset items such as Pan/Tilt location,
Zoom and Focus, which are selected among camera functions.
Execute : Select the Preset number for execution.
Clear : Select the Preset number to delete for clearing.
Status : The current Preset number setup is displayed.
80
Preset Menu Setting

1. Select the Preset item on the Sequence Setting Menu
2. Select the Setting item.
3. Select the Preset number.

4. Set up the Zoom and Focus.
5. To change the camera settings, select Edit from the upper menu
first. Select the item to change, and then make the necessary
adjustments.
6. If you select the Scene Adj. item, such items as Shutter, AGC,
SSNR, Sens-Up, White Balance can be set up differently in
every Preset item.
81
In the White Balance setting of the individual Preset

Note Scene Adj., the AWC selection is not available.
5.3.2. Swing SEQ

Swing surveillance can be executed and set up and the data can be
deleted.
Pan Swing : Swing surveillance for the Pan direction is executed

and set up. Data is deleted.
Tilt Swing : Swing surveillance for the Tilt direction is executed
and set up. Data is deleted.
P&T Swing : Swing surveillance both for the Pan and the Tilt
directions are executed and set up simultaneously. Data is
deleted.
- Setting : The Preset Position for Swing function is selected by
clicking the mouse and confirmed with the Execution key. SPD
82
is the moving speed (01-64step). DWL is the stop time (00-

120sec). Press the Execution key in the location with selection
mark to finish the setting process.
- Execute : Swing surveillance is executed. Stop key designates
this function.
- Clear : Data in the Swing function is deleted.
5.3.3. Group SEQ

Group SEQ: Sequence surveillance can be executed and set up and
data can be deleted. Up to 6 groups can be registered.
Setting : Preset position for swing is selected by clicking the

mouse and confirmed with the Execution key. SPD is the moving
speed (01~64 step). DWL is the stop time (00~120sec). Press
the Execution key in the location with selection mark to finish the
setting process.
Execute : Swing surveillance can be executed. Stop key will stop
this function.
Clear : Swing data can be deleted.
5.3.4. Tour SEQ

Group surveillance can be executed and set up and data can be
deleted.
83
Setting : The registered Group Sequence is selected by clicking

the mouse and confirmed with the Execution key. If the selected
number is not registered, it cannot be input. Press the Execution
key in the location with selection mark to finish the setting
process.
Execute : Group surveillance is executed.
Clear : Group surveillance data are deleted.
5.3.5. PTZ Trace

Maximum 4 patterns of the manual operation paths (for Pan, Tilt,
Zoom and Focus) are memorized and replayed.
Replay : The manual operation paths are repeated and replayed.

Stop key will stop the replay.
If the operation range is limited using ①Pan Limit

Note and ②Tilt Limit, please note that other operations
84
Memorize: Manual operations for minimum 120 seconds after

executing this function are memorized into the internal memory.
Nevertheless, the memorizing time becomes different depending
on the PTZ operation. OVER mark will finish this function.
If the operation range is limited using ①Pan Limit

and ②Tilt Limit, only the operations within the limited
Note range are memorized.
Press the OSD key to stop the internal memory to

Note continue saving.
5.3.6. Auto Run

If there is no controller operation by the user for a certain time, the
sequence operation designated by the user will be executed.
Mode:
- OFF : Auto Run will be cancelled.
- Preset : Auto Run in the corresponding Preset number
- Swing : Auto Run in the corresponding Swing mode
- Group : Auto Run in the corresponding Group number
- Tour : Auto Run in the corresponding Tour number
- Trace : Auto Run in the corresponding Trace number
- A. Pan : 350° Auto Run in Pan direction
※ Auto Pan Speed: Pan operation in the speed designated by
the user.
※ Tilt Angle: The tilt angle set up by the user is kept.
85
Time : Auto Run operation is executed after a certain time

designated by the user.(Time can be set up by the unit of 5, 10,
20, 30 sec and 1~5 min.)
5.3.7. Power On Resume

When the power supply for the camera is stopped for some reason,
such as electricity failure, and resumed, the Sequence Settings
before the power off are restored.
86
5.4. P/T Setting
5.4. P/T Setting
5.4.1. Pan Limit

The moving range in the Pan direction can be limited.
Position : Moving range can be set up. Set the position from the
left using the Execution key. The stop position may change due
to the initialization by such operation as power resumption
depending on position setting. This does not mean it is out of
order.
On/Off : When this function is on, the limit is effective. Default
setting is Off.
5.4.2. Tilt Limit

Moving range in the tilt direction can be limited.
Position : Moving range can be set up. Set the position from the
top direction using the Execution key. The stop position may
change due to initialization by such operation as power
87
resumption depending on position setting. This does not mean it

is out of order.
On/Off : The application of limitation will be determined. Default
setting is Off.
5.4.3. Area Setting

Areas can be indicated. Areas can be designated up to 4.
Area Name : Area name can be set up. Use the Execution key to
enter the area name. A maximum of 12 letters (English, Chinese,
numbers) can be entered. When you finish inputting the name,
adjust the position mark to ”SET” and press the Execution key.
This is the end of Area Name setting.
Area Position : Area range can be designated. Use the Execution
key to determine the position from the left. If the area range is
overlapped, the smaller area number will indicate the overlapping
part.
On/Off : It can be determined whether or not to activate the area
mark. The activation becomes effective as soon as the position
moves from the current area to other areas. Set up the OSD
Setting as ON. If it is in OFF mode, this function does not work.
Default setting is OFF.
88
5.4. P/T Setting
5.4.4. Area Masking

If you want to exclude some areas for surveillance, they can be
turned into black. You can mask 4 parts of one screen.
Position : Use the Execution key to determine the position for

screen operation from the left.
On/Off : Operation of screen area masking can be determined.
Default setting is OFF.
If Area Masking is set while the Camera is in the

Digital Flip posion, automatically the Camera moves
Note the initial position which is not set for the Digital Flip
and then Area Masking position can be set. This is
not a malfunction.
5.4.5. Prop. P/T

Pan and Tilt speeds can be changed depending on zoom
magnification. Tele will slow down the speed of Pan/Tilt and Wide
will increase the Pan/Tilt speed. It will take about 20 seconds for 1
cycle in Tele mode and about 3 seconds in the Wide mode. Default
setting is ON.ed. Default setting is OFF.
89
5.4.6. Digital Flip

When you operate the Tilt up to 100° limit and keep it for a certain
time, the image gets reversed automatically and the opposite Tilt
area is seen. When you want to monitor the moving object under the
camera, execute the Digital Flip function. You can observe the
moving object without reversing of the screen.
5.4.7. Jog Speed

Because using Pan/Tilt command protocol is fixed speed type ,so
that occation that Pan/Tilt speed is slow, can adjust command rate
by enter manual mode.
90
5.5. OSD Setting
5.5. OSD Setting
5.5.1. Camera Name

Camera name is set up.
If you want to edit the item, move the cursor. Then

Note select the character.
y Edit : A maximum of 12 characters consisting of English (or

Chinese, Japanese), numbers and special characters can be
input for Camera Name.
y On/Off : The operation of this function is preset. Default setting is

On.
91
5.5.2. Preset Number

Preset numbering is set up. (Default setting is ON.)
5.5.3. Preset Name
Edit : A maximum of 12 characters consisting of English (or

Chinese), numbers and special characters can be input for
Preset Name.
92
5.5. OSD Setting
On/Off : The operation of this function is predetermined. Default

setting is On.
5.5.4. Sequence Status

Display of the Sequence Group is set up. (Default setting is ON.)
5.5.5. Area Name

Display of Area Name is set up.
When the Area Name is OFF, the Area Name cannot be displayed.
93
5.5.6. PTZ Position

Pan and Tilt position and Zoom magnification are displayed.
PTZ positions are not displayed in the OFF mode. (Only manual
operation can display them.)
5.5.7. Language
The OSD can be displayed either in English (default setting) ,
Chinese, French, German, Italy and Spanish.
94
5.6. Initialization Setting
5.6. Initialization Setting
Initialization Menu
①Power On Reset
Camera is initialized into the original status of power input.
➋Initial Position
If you want to set the default direction of the camera so that the
camera faces that direction when the power is turned on, you can set
up the desired Pan and Tilt for the camera.
③Factory Default Settings

Camera is initialized into the factory default settings.
Data including Preset is deleted. This function is used for

initialization all settings.
④Camera Default Settings

If only the camera module is replaced due to camera module failure,
the new camera module can be set up with the settings of the old
camera module.
➎ Auto Refresh
The electric circuit and the status of the equipment parts within the
camera are optimized regularly. (The cycle can be set up.) If camera
faces toward a certain source of light or if the settings cannot be
kept because of the long time rotation filming of a certain area, the
Auto Refresh function is used to maintain and reset the existing
95
camera settings. Default setting is OFF.

OFF, 1-7 Days : This function is disabled in the OFF mode. 1-7
Days enables the Auto Refresh operation in the interval of the
selected days. Auto Refresh takes less than 10 seconds. The
message “Auto Refresh” disappears after finishing the operation.
5.7. Status
The status of PTZ camera setting is displayed.
CAM MODEL= 10NC Camera Model

CAM VERSION= 4.6 Camera S/W Version
DOME VERSION= 1.00 Control Board S/W Version
CON PROTOCOL=SAMSUNG TW Protocol Setup
DOME ID= 001 Dome Camera ID
CONTROLLER= Duplex-19200 Communication Mode Setup
96
C h 6. Troubleshooting
If there are problems in operation, please refer to the items below. If

the problem persists, please contact the agent you purchased this
product from.
Problem Solution
Nothing appears on the Please check the power connection.
screen.
Please check the images after
connecting the video signal line
Open MS-DOS window to check
whether 10X PTZ Network Camera
SNP-1000A is connected to network.
※ In case of ping 192.168.1.100,
replace it with IP address set up.
The video image is not Please check if the lens is clean.

clear. Please clean the lens with a clean
cloth or brush.
Please adjust the contrast feature of
the monitor.
Please make sure that the screen is
not exposed directly to a bright light.
Please move the camera if necessary.
The screen is dark. Please adjust the contrast feature of
the monitor.
If you have an intermediate device, set
the 75Ω/Hi-z properly, and check the
terminals.
There is a problem with Please check if an appropriate power
the camera operation. source to the camera complies with
The camera surface is
the manufacturer's standard
too hot and black
stripes appear on the requirement, or if the voltage keeps
screen. changing.
98
Troubleshooting
Problem Solution
The MOTION Please check if 'MOTION
DETECTION function is DETECTION' mode is turned on.
not working.
Please check if the MD LEVEL is too
low.
Please check the setting of the MD
AREA.
When camera cannot Inspect the cables(power or network)
be controlled for Pan/ connected to the device.
Tilt/ Zoom
Connect to Admin page to check
whether user control is selected.
Colors are not quite Please check the 'WHITE BAL'
right. setting.
The screen is Please check if the camera is facing
flickering. directly into sunlight or fluorescent
light.
DAYNIGHT(Auto) mode Please check if the AGC menu is set
is not working. to the OFF position.
SENS-UP function is Please check if the AGC menu is set
not working. to the OFF position.
Please check if the SHUTTER menu
is set to MANUAL mode.
Please check the limit of SENS-UP
AUTO mode.
Audio is not working Please check the audio is selected
from admin page.
Please check speaker volume from
the viewer.
In case input sound through
microphone at Viewer is not outputted
through Audio Out of camera, please
check whether Audio Out channel is
selected at admin page. Or check
whether microphone is available at
Viewer.
99
Problem Solution
Please check audio driver is working
in user’s PC.
Please use the enclosed Audio
Extension Cable to install easily when
connecting the audio cable.
Video is stopped Please check whether network cable
of 10X PTZ Network Camera SNP-
1000A is correctly connected
In case user uses hub or IP router,
check whether these network
equipments are working properly.
Open MS-DOS window and check
whether 10X PTZ Network Camera
SNP-1000A is connected to network.
No image from web Click ‘refresh (shortcut; F5) ’ button at
viewer browser to recall the page
Check whether power of camera and
network cable is properly connected.
Check whether computer is connected
to network.
If you use hub or router, check
whether such equipments are properly
operated.
(Note: Open MS-DOS window and
enter network ID of camera at ping
192.168.1.100)
Connect to Admin page to check
whether video output is selected.
Image transferred to Video may not be viewed since Divx
FTP or by E-mail codec is not installed in user’s PC.
cannot be viewed
Divx codec can decode video
compressed with MPEG4. Download
and install the latest Divx codec, and
check video.
http://www.divx.com/divx/download
100
A p p e n d ix A . D D N S U s a g e
Registration process of DDNS is as following:
Step1) Complete the registration form in iPOLiS

website.
The website is ‘www.samsungipolis.com’.
Figure A-1. Website of iPOLiS
102
DDNS Usage
Figure A-2. Membership Registration: SIGNUP
Figure A-3. Membership Registration: Input your information.
103
Step2) Register the equipment after login.
Figure A-4. Login
Figure A-5. The list of registered equipment.
104
DDNS Usage
Figure A-6. Product Registration.

(Confirm repetition certainly at domain registration.)
Figure A-7. The list of registered equipment.
105
Step3) Configure DDNS information in the

equipment.
Click the part of Network Configuration in website of Network
Camera.
Click “USE DDNS” in order to do “Enable” and input the address
of DDNS Server.
(Default: www.samsungipolis.com )
Enter the ID and Password that is written when register product
is in iPOLiS website.
The Configuration of DDNS in SNP-1000A is Completed.
106
DDNS Usage
Step4) Confirm the connection status of

relevant product in product list of iPOLiS
website.
Figure A-8. The List of Product.
Be able to confirm the information of connected

equipment if click <check> button of ‘Product information’.
107
Figure A-9. Product information
Move to Login website of relevant product if click <view>

button of ‘ view’.
The buttons which are <Edit> and <Delete> of ‘product

management’ move to relevant page through input
password to item that fertilize or erase information of
registered equipment in List of product.
Only, ‘ID(Domain)’ of product should establishes again as

‘ID(Domain)’ after deleting because it can’t be fertilized.
Figure A-10. Edit/Delete
108
Specifications
Specifications
Camera Part
Items SNP-1000AN SNP-1000AP
1/4” Color Vertical Double Density Interline CCD.
Imaging device
410,000pixel
TV NTSC PAL
Total Number of Pixels 811(H) X 508(V) 795(H) X 596(V)
Valid Pixel 768(H) X 494(V) 752(H) X 582(V)
Horizontal Scan
15.734kHz 15.625KHz
Frequency
Vertical Scan
59.94Hz 50Hz
Frequency
Synchronization Internal Sync
Image Output 1.0p-p/75Ω
S/N Ratio Higher than 50dB (AGC OFF)
Horizontal Resolution 520 TV Lines (Color)/570 TV Lines(B/W)
Minimum Light for 0.7Lux(Color), 0.1Lux(B/W)/(@50IRE),
Object 0.0007Lux (Day & Night is On.)/(@50IRE)
Auto/Manual Auto/Manual
Electronic Shutter
(1/60 - 1/120,000) (1/50 - 1/120,000)
Sens-Up ON (x2 - x128 Fields) / OFF
Day & Night ICR(Filter Switching) ON/OFF
ATW(Indoor/Outdoor Selection)/AWC/
White Balance
Manual (1,800K - 10,500K)
Fixed Shutter Speed Fixed Shutter Speed
Flickerless Adjustment
(1/100) (1/120)
Iris Auto/Manual (Iris Level Adjustment Mode)
Gain Control Low, Middle, High, Off
OSD Display ON/OFF
Outline Correction Adjustable Level
Focal Length F3.8mm(WIDE)~F38.0mm(TELE), 10X Optical Zoom
Digital Zoom OFF, 2~10X Selection (Total 100X Zoom)
Maximum Aperture Wide Angle 1:1.6, Tele 1:2.8
Rate
Coverage Angle Wide: 51.2°(H) X 39.3°(V) Tele: 5.58°(H) X 4.27°(V)
Proximity Distance 1.5m(Tele)
Horizontal Rotation
350°
Angle
Horizontal Rotation Manual/Program
109

Horizontal Rotation Manual: 0.5° ~ 70°/s(64 levels)
Speed Preset: 0.5° ~ 140°/s(64 levels)
Horizontal Minimum
0.02°
Moving Angle
Vertical Rotation Angle -5°~ 185° (Digital Flip)
Vertical Rotation Manual/Program
Manual: 0.5° ~ 150°/s(64 levels)
Vertical Rotation Speed
Preset: 0.5° ~ 100°/s(64 levels)
Vertical Minimum
0.02°
Moving Angle
Preset Position Max 128 points
Area Masking Max 4 locations
2 Alarm Inputs
Alarm 1 Alarm Outputs
(Relay: NC/NO/COM, 2A 30VDC Max)
Operating Temperature 0°C ~ 40°C
Operating Humidity 20% ~ 75%(Except for dew condensation)
Power, Voltage DC 12V±10%
Power Consumption Operating 8.5Watts below
Dimension Ø110 X 134.8mm
Weight Less than 0.85kg
- Wall Mount Bracket : STB-280PW
Option - Wall Mount Bracket : STB-230PW
- Dome Housing : STH-1000PI
※ The product design and dimensions may change without
previous notice for improvement of performance.
The copyright of this manual belongs to Samsung

Techwin Co. Ltd.
Note
Parts or the whole of this manual cannot be
reproduced or transmitted by any electric,
mechanic or audio method without the authorized
written approval of Samsung Techwin.
The contents of this manual may be changed for
an improvement of functions.
110
Specifications
Network Part
NTSC :
704 x 480(D1), 704 x 240(Half D1), 352 x 240(CIF)
Output Resolution
PAL :
704 x 576(D1), 704 x 288(Half D1), 352 x 288(CIF)
Output Video Format MPEG4 / MJPEG Selectable
Video Compression
5 stages (Very Low, Low, Middle, High, Very High)
Stage
Compression NTSC : MAX 30 frame/sec
transmission speed PAL : MAX 25 frame/sec
Audio Format Bi-directional audio, 8KHz ADPCM
Ethernet 10/100Mbps
HTTP, TCP/IP, FTP, SMTP, DHCP, DNS, DDNS, NTP,
Protocol
PPPOE
Dynamic IP Supports XDSL and DHCP
DDNS Supports DDNS
Area Zoom Supports Area Zoom function
Max. User 20 Users
Supply Network Manager Standard Installation
S/W
Program
※ The product design and dimensions may change without
previous notice for improvement of performance.
111
Dimension
112
SAMSUNG TECHWIN
SALES NETWORK
SAMSUNG TECHWIN CO., LTD. SAMSUNG OPTO-ELECTRONICS UK, LTD.
145-3, Sangdaewon-dong, Jungwon-gu, Samsung House, 1000 Hillswood Drive,
Seongnam-si, Gyeonggi-do, 462-120, Korea Hillswood Business Park Chertsey, Surrey KT16 OPS
Tel: +82-31-740-8151~8 Fax: +82-31-740-8145 Tel: +44-1932-45-5308 Fax: +44-1932-45-5325
SAMSUNG OPTO-ELECTRONICS AMERICA, LTD.

1480 Charles Willard St. Carson, CA90746
Tel: +1-310-632-1234 Fax: +1-310-632-2195
www.samsungtechwin.com
www.samsungipolis.com P/NO : Z6806.0915.01B

SNP 1000a Eng

Uploaded by

Copyright:

Available Formats

SNP 1000a Eng

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SNP 1000a Eng

Uploaded by

Copyright:

Available Formats

Real-time Network

10X PTZ Network Camera SNP-1000A User’s Manual

A brand that is integrated into Samsung's network products,

Thanks for purchasing of 10X PTZ Network Camera SNP-1000A.

This is a user instruction manual for a 10X PTZ Network Camera

So the copy, reprint and translation to other languages of a part of or

Ch1. Overview .......................................................................13

1.1. 10X PTZ Network Camera SNP-1000A Introduction .......14

Ch2. Section names and functions .....................................17

2.1. Body ........................................................................18

Ch3. Installation and Network Setup...................................21

3.1. Components and Accessories.................................22

3.3. Network configuration and connection method .......32

Ch4. How to Use Web Viewer...............................................37

4.1. How to Use Web Viewer..........................................38

4.2. Using Administration page.......................................49

Ch5. How to Operate Camera...............................................67

5.1. OSD Menu Organization .........................................68

5.3. Sequence Setting ....................................................80

5.4. P/T Setting...............................................................87

5.5. OSD Setting ............................................................91

5.5.5. Area Name ............................................................. 93

5.6. Initialization Setting .................................................95

Ch6. Troubleshooting ...........................................................97

Appendix A. DDNS Usage...................................................101

If you refer to the enclosed Quick guide and the

This machine’s electromagnetic waves have been registered as

Correct Disposal of This Product

(Applicable in the European Union and other

This marking shown on the product or its literature, indicates that it

Samsung Techwin cares for the environment at all

Correct disposal of batteries in this product

(Applicable in the European Union and other

This marking on the battery, manual or packaging indicates that the

To protect natural resources and to promote material reuse, please

Product Warranty and Limitations

The manufacturers of this product do not take any responsibility for

The product warranty does not extend to cover accidents, negligence,

y Malfunction due to user’s negligence

y Connection to alternate power source

y Malfunction due to natural disasters (fire, flood, tsunami, etc.)

y Replacement due to wear and tear

Before attempting to connect or operate this product,

y There is risk of shock or fire; be sure to avoid setup in places

y To prevent shocks, please connect the ground wire.

y Unless the surface is suitable, it could cause falling or other

y Please use only in an environment with standard temperature

y Please do not plug in multiple products to a power source; it is

y Please do not place water or heavy objects on the product; it is

y Please do not use in a location with propane gas, gasoline or

y Don’t connect the RJ-45 cable to a terminal by constraint.

y Stop using your camera when you find a malfunction.

y Random replacement of built-in battery by other types of

y The used batteries shall be disposed carefully because they can

Disassembly and Cleaning

y To prevent malfunction or shock, please do not use a wet cloth

y Do not install under extreme temperature conditions

y Do not install under unstable lighting conditions.

y Do not drop the camera or subject it to physical shock.

10X Zoom Lens with Auto-Focus Function

Variable Auto Surveillances

Day & Night

OSD (On Screen Display)

128 Preset Position

High Data Compression Ratio

Products Sold Separately

See pages 26 for product images.

Video cable and LAN network cable are not

Precautions for Installation

Optional Products for Installation