007 Megane

8 Electrical equipment
ENGINE IMMOBILISER
82A
SVT
Vdiag No.: 04
Fault finding – Introduction 82A - 2

Fault finding – List and location of components 82A - 8
Fault finding – Features 82A - 9
Fault finding – Configurations and programming 82A - 10
Fault finding – Replacement of components 82A - 11
Fault finding – Fault summary table 82A - 12
Fault finding – Interpretation of faults 82A - 13
Fault finding – Conformity check 82A - 20
Fault finding – Status summary table 82A - 21
Fault finding – Interpretation of statuses 82A - 22
Fault finding – Parameter summary table 82A - 28
Fault finding – Interpretation of parameters 82A - 29
Fault finding – Customer complaints 82A - 30
Fault finding – Fault finding chart 82A - 31
V3 Edition Anglaise
"The repair procedures given by the manufacturer in this document are based on the All rights reserved by Renault s.a.s.
technical specifications current when it was prepared.
Copying or translating, in part or in full, of this document or use of the service part
The procedures may be modified as a result of changes introduced by the reference numbering system is forbidden without the prior written authority of
manufacturer in the production of the various component units and accessories from Renault s.a.s.
which his vehicles are constructed."
© Renault s.a.s. 2013

MR-366-X84-82A050$TOC.mif
V3
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding method applicable to all computers with the following specifications:
Vehicle(s): LOGAN, SANDERO, DUSTER,

MEGANE II ph1 and ph2, SCENIC II, MASTER II
Computer name: SVT
ph2 and ph3, THALIA 2/SYMBOL 2, CLIO II F6,
KANGOO VLL*
Function concerned: Anti-Theft Tracking Unit Vdiag No.: 04
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this document):
– Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
– Visu - Schéma.
Type of diagnostic tools

– CLIP + multiplex line sensor
Special tooling required
Special tooling required

Diagnostic tool
Multimeter
Elé. 1681 Universal bornier
3. SAFETY INSTRUCTIONS
Safety rules must be observed during any work on a component to prevent any material damage or personal injury:
– check the battery voltage to avoid incorrect operation of computer functions,
– use the proper tools.
– It is forbidden to carry out a road test with the diagnostic tool in dialogue with the ECU because the ABS
and Electronic Brake Distribution functions are deactivated. Braking pressure is identical on both axles of
the vehicle (risk of a spin under heavy braking).
*VLL — Very Long Life
SVT_V04_PRELI
MR-366-X84-82A050$010.mif
V3
82A-2
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
4. REMINDER
Procedure
To run fault finding on the vehicle computers, switch on the ignition. Connect the diagnostic tool and perform the
required operations.
SCENIC II and MEGANE II:

To run fault finding on the vehicle computers, switch on the forced + after ignition feed.
Proceed as follows:
Switch on the forced + after ignition feed:

– with the vehicle card in the card reader,
– press and hold the Start button (longer than 5 seconds) with start-up conditions not fulfilled,
– connect the diagnostic tool and perform the required operations.
Switching off the forced + after ignition feed:

Press the Start button twice briefly (less than 3 seconds).
Ensure that the + after ignition feed has been cut off by checking that the computer warning lights on the instrument
panel have gone out.
LOGAN, SANDERO, DUSTER, MASTER II ph2 and ph3, THALIA 2/SYMBOL 2, CLIO II F6, KANGOO VLL
To run fault finding on the vehicle computers, switch on the + after ignition feed.
Proceed as follows:
For vehicles with key/radiofrequency remote control unit,

switch on the ignition with the key.
MR-366-X84-82A050$010.mif
V3
82A-3
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Faults
Faults are declared present or stored (depending on whether they appeared in a certain context and have
disappeared since, or whether they remain present but are not diagnosed within the current context).
The present or stored status of faults must be considered when the diagnostic tool is used after the + after ignition
feed is switched on (without operating the system components).
For a present fault, apply the procedure described in the Interpretation of faults section.
For a stored fault, note the faults displayed and apply the Notes section.
If the fault is confirmed when the instructions in the Notes section are applied, the fault is present. Deal with the
fault.
If the fault is not confirmed, check:
– the electrical lines which correspond to the fault,

– the connectors for these lines (for oxidation, bent pins, etc.),
– the resistance of the faulty component,
– the condition of the wires (melted or split insulation, wear).
Customer complaints - Fault finding chart
If the test with the diagnostic tool is OK but the customer complaint is still present, the fault should be processed by
customer complaints.
A summary of the overall procedure to follow is provided on the following page in the form of a flow chart
MR-366-X84-82A050$010.mif
V3
82A-4
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
5. FAULT FINDING PROCEDURE
Perform a pre-diagnostic on the

system
Print the system fault finding log

(available on CLIP and in Repair
Manual or Technical Note)
Connect CLIP
Dialogue with No
computer? See ALP no. 1
yes
Read the faults
Faults No
present Conformity check
Yes
Deal with present faults The cause is

No
still present Fault
solved
Yes
Deal with stored faults
Use fault finding charts (ALPs)
The cause is No
Fault The cause is
No
still present Fault solved
solved still present
Yes
Yes
Contact the Techline with the
completed fault finding log
MR-366-X84-82A050$010.mif
V3
82A-5
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
5. FAULT FINDING PROCEDURE (continued)
Wiring check
Fault finding problems

Disconnecting the connectors and/or manipulating the wiring may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulators and wiring harness routing.
Look for signs of oxidation.
Physical inspection
While manipulating the wiring, use the diagnostic tool to note any change in fault status from stored to present.
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Inspection of each component

Disconnect the connectors and check the appearance of the clips and tabs, as well as the crimping (no crimping on
the insulating section).
Make sure that the clips and tabs are properly locked in the sockets.
Check that no clips or tabs have been dislodged during connection.
Check the clip contact pressure using an appropriate model of tab.
Resistance check
Check the continuity of entire lines, then section by section.
Look for a short circuit to earth, to + 12 V or with another wire.
If a fault is detected, repair or replace the wiring harness.
MR-366-X84-82A050$010.mif
V3
82A-6
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
6. FAULT FINDING LOG
IMPORTANT
All faults involving a complex system call for thorough diagnostics with the appropriate tools. The
FAULT FINDING LOG, which should be completed during the fault finding procedure, ensures a
record is kept of the procedure carried out. It is an essential document when consulting the
IMPORTANT! manufacturer.
IT IS THEREFORE COMPULSORY TO COMPLETE A FAULT FINDING LOG

EACH TIME IT IS REQUESTED BY TECHLINE OR THE WARRANTY RETURNS DEPARTMENT.
You will always be asked for this log:

• when requesting technical assistance from Techline,
• for approval requests when replacing parts for which approval is mandatory,
• to be attached to monitored parts for which reimbursement is requested. The log is needed for warranty
reimbursement, and enables better analysis of the parts removed.
7. INSTRUCTIONS TO BE FOLLOWED FOR ANY WORK CARRIED OUT ON THE INJECTION SYSTEM
Instructions to be followed before opening of the fuel circuit
Use fresh cleaning agent for each operation (used cleaning agent is contaminated). Pour it into an uncontaminated
container.
For each operation, use a clean brush in good condition (the brush must not shed its bristles).
Use a brush and cleaning agent to clean the unions to be opened.
Blast compressed air over the cleaned parts (tools, workbench, and the parts, unions and injection system area).
Check that no bristles remain.
Wash your hands before and during the operation if necessary.
When wearing leather protective gloves cover them with latex gloves to prevent contamination.
Instructions to be followed during the operation
As soon as the circuit is open, all openings must be plugged to prevent impurities from entering the system. The
plugs to be used are available from the Parts Department. The plugs must not be reused under any circumstances.
Seal the pouch shut, even if it has to be opened shortly afterwards. Ambient air carries impurities.
All components removed from the injection system must be stored in a hermetically sealed plastic bag once they
have been plugged.
The use of a brush, cleaning agent, bellows, sponge or normal cloth is strictly forbidden once the circuit has been
opened. These items could allow contamination to enter the system.
A new component replacing an old one must not be removed from its packaging until it is to be fitted to the vehicle.
MR-366-X84-82A050$010.mif
V3
82A-7
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – List and location of components
SVT computer:
For MEGANE II and SCENIC II:

With its attached support, it is bolted on the existing support of the dashboard cross member.
For MASTER II ph2 and ph3, THALIA 2/SYMBOL 2, CLIO II F6, KANGOO VLL:
The computer support is bolted on the existing support of the dashboard cross member.
For LOGAN, SANDERO and DUSTER:

The computer support is welded to the dashboard cross member.
The anti-theft tracking unit (computer) consists of:
– An integrated GPS aerial to locate the vehicle.
– An integrated GSM aerial to communicate with a call centre.
– A locking system that prevents the vehicle from operating when the owner of the vehicle declares to the call
centre that the vehicle has been stolen.
– An external GPS aerial can be connected to the anti-theft tracking unit, on certain vehicle types.
MR-366-X84-82A050$020.mif
V3
82A-8
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Features
For LOGAN, SANDERO, DUSTER, MASTER II ph2 and ph3, THALIA 2/SYMBOL 2, CLIO II F6, KANGOO VLL:
The computer can switch off the electrical supply of the transponder ring. When the anti-theft tracking unit receives a
locking order from the call centre via the GSM network, it switches off the supply of the transponder ring.
For "no hands-free opening" vehicles, the computer can switch off the electrical supply of the card reader. When the
anti-theft tracking unit receives a locking order from the call centre via the GSM network, it switches off the supply of
the card reader.
For "hands-free opening" vehicles, the computer can switch off the electrical supply of both the card reader and the
steering column lock. When the anti-theft tracking unit receives a locking order from the call centre via the GSM
network, it switches off the supply of these two components.
The computer has several operating modes:
– NOT FUNCTIONING mode: The computer is not supplied. No function is available, but the system retains the
stored configuration and the recorded data.
– DEACTIVATED mode: The ignition is off. The computer is supplied by the vehicle battery. Vehicle tracking by
the call centre is not activated and the GSM network does not send the vehicle position to it. The computer
stores the satellite position in its memory every 24 hours.
– FUNCTIONING WITHOUT TRACKING mode: Ignition on. The computer is supplied by the vehicle battery.
Vehicle tracking by the call centre is not activated. The computer is registered on the GSM network in case
tracking is activated. The GSM network does not send the vehicle position to the call centre. The computer
stores the satellite position in its memory every minute.
– DEACTIVATED WITH TRACKING mode: The ignition is off. The computer is supplied by the vehicle battery.
Vehicle tracking by the call centre is activated. The computer sends the vehicle position message to the call
centre every 24 hours. Each time the computer is activated, it makes a record on the GSM network and
communicates it to the call centre, but does not store it in its memory.
– FUNCTIONING WITH TRACKING mode: Ignition on. The computer is supplied by the vehicle battery. Vehicle
tracking by the call centre is activated.
The computer sends the vehicle position message to the call centre every minute. The computer stores in its
memory all operations ordered by the call centre.
– VIOLATION mode: The computer is supplied by its internal battery. The computer sends the vehicle position
message to the call centre every minute. The main supply (+ Battery) is switched off. The GPS module is
activated after a position violation is detected.
– FAULT FINDING mode: The computer is supplied by the vehicle battery or by its internal battery. The computer
communicates with the diagnostic tool.
MR-366-X84-82A050$030.mif
V3
82A-9
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Configurations and programming
SPECIAL COMMANDS
VP001 Enter VIN

This command permits manual entry of the vehicle's VIN into the computer.
Use this command each time the computer is replaced or (re)programmed.
Procedure for writing the VIN

• Establish dialogue with the computer.
• Select the menu repair mode.
• Select the other parameters menu.
• Select the line VP001.
• Enter the VIN.
• Exit fault finding mode.
• Switch off the ignition.
• Wait for the end of power latch.
• Reread the VIN in the Identification menu for confirmation (ID004 "VIN").
RZ001: Clear faults

This command is used for clearing the stored faults from the computer.
CONFIGURATION READING
CF001: CONFIGURE SVT

LC001: External GPS aerial
LC002: Timed + battery feed
LC003: Alarm
MR-366-X84-82A050$040.mif
V3
82A-10
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Replacement of components
To remove and refit the computer, consult the Repair Manual for the vehicle concerned:
– LOGAN and SANDERO: MR 388, Mechanical, 82A, Immobiliser, Tracking unit: Removal - Refitting.
– DUSTER: MR 451, Mechanical, 82A, Immobiliser, Tracking unit: Removal - Refitting.
– MEGANE II: MR 364, Mechanical, 82A, Immobiliser, Tracking unit: Removal - Refitting.
– SCENIC II: MR 370, Mechanical, 82A, Immobiliser, Tracking unit: Removal - Refitting.
– MASTER II ph2 and ph3: MR 377, Mechanical, 82A, Immobiliser, Tracking unit: Removal - Refitting.
– THALIA 2/SYMBOL 2: MR 423, Mechanical, 82A, Immobiliser, Tracking unit: Removal - Refitting.
– Clio II F6: MR 430, Mechanical, 82A, Immobiliser, Tracking unit: Removal - Refitting.
– KANGOO VLL: MR 374, Mechanical, 82A, Immobiliser, Tracking unit: Removal - Refitting.
Procedure to be applied before repair:
– With the approval of the Techline, read the fault code to determine whether the fault is detected before replacing
the computer.
– Switch off the ignition and remove the computer.
Before replacing the computer, switch off the ignition and wait 1 minute for the system to shut down completely.
Note the current configuration of the computer by reading the configuration LC001 External GPS aerial.
Procedure to be applied after repair:
After replacing the computer, apply the programming command VP001 Enter VIN, check the computer configuration
using LC001 External GPS aerial, LC002 Timed + battery feed and LC003 Alarm and configure the new
computer if necessary using CF001 CONFIGURE SVT.
MR-366-X84-82A050$050.mif
V3
82A-11
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Fault summary table
Associated
Tool fault Diagnostic tool title
DTC
DF001 9A01 External GPS aerial

DF002 9A02 GPS internal error
DF003 9A03 GSM internal error
DF004 9A05 Battery internal fault
DF005 9A09 SVT internal fault
DF006 9A04 SVT system internal fault
DF007 9A00 Configuration
MR-366-X84-82A050$060.mif
V3
82A-12
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Interpretation of faults
DF001 EXTERNAL GPS AERIAL

PRESENT
OR
STORED
NOTES Switch on the vehicle + after ignition feed.
Check the configuration of the anti-theft tracking unit by reading configuration LC001 External GPS aerial.
If the check is not correct, use command CF001 CONFIGURE SVT.
Check the condition of the aerial visually and by hand.

Disconnect then reconnect the aerial.
If the fault is still present, contact the Techline.
Deal with any faults displayed by the diagnostic tool.

AFTER REPAIR
Clear the faults from the computer memory using command RZ001 Fault memory.
SVT_V04_DF001
MR-366-X84-82A050$070.mif
V3
82A-13
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
DF002 GPS INTERNAL ERROR

PRESENT
OR
STORED
Replace the anti-theft tracking unit (see MR 388, 451, 364, 370, 377, 423, 430, 374, Mechanical, 82A,
Immobiliser, Tracking unit: Removal - Refitting).
After replacing the computer, consult the Replacement of components section.

AFTER REPAIR Deal with any faults displayed by the diagnostic tool.
SVT_V04_DF002
MR-366-X84-82A050$070.mif
V3
82A-14
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
DF003 GSM INTERNAL ERROR

PRESENT
OR
STORED
Replace the anti-theft tracking unit (see MR 388, 451, 364, 370, 377, 423, 430, 374, Mechanical, 82A,

SVT_V04_DF003
MR-366-X84-82A050$070.mif
V3
82A-15
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
DF004 BATTERY INTERNAL FAULT

PRESENT
OR
STORED
Switch on the vehicle + after ignition feed.
NOTES
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present if the battery voltage is X < 3.5 V after 5 voltage checks.
Check the voltage and the battery connections, component code 107.
Repair if necessary.
If the fault is still present and the internal battery is currently charging, wait for approximately 2 hours so that the
internal battery voltage is X > 3.5 V.
If the fault is still present, replace the anti-theft tracking unit, component code 2186 (see MR 388, 451, 364, 370,
377, 423, 430 or 374, Mechanical, 82A, Immobiliser, Tracking unit: Removal - Refitting).

SVT_V04_DF004
MR-366-X84-82A050$070.mif
V3
82A-16
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
DF005 SVT INTERNAL FAULT

PRESENT
OR
STORED
Replace the anti-theft tracking unit (see MR 388, 451, 364, 370, 377, 423, 430 or 374, Mechanical, 82A,

SVT_V04_DF005
MR-366-X84-82A050$070.mif
V3
82A-17
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
DF006 SVT SYSTEM INTERNAL FAULT

PRESENT
OR
STORED
Replace the anti-theft tracking unit (see MR 388, 451, 364, 370, 377, 423, 430 or 374, Mechanical, 82A,

SVT_V04_DF006
MR-366-X84-82A050$070.mif
V3
82A-18
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
CONFIGURATION
DF007
PRESENT
Configure the system (see Configuration and programming).
Note:
After configuring, switch off the ignition, wait 2 minutes then switch on the ignition again to allow the configuration
to register.
Check the computer configuration by reading configuration LC001 External GPS aerial.

AFTER REPAIR
SVT_V04_DF007P
MR-366-X84-82A050$070.mif
V3
82A-19
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Conformity check
NOTES Only check conformity after a full check with the diagnostic tool.
MAIN SCREEN or SUB-FUNCTION: STARTING
Status or parameter checked

Function Notes Fault finding
or action
Refer to the
ET001: SVT operational none
interpretation of ET001
System activation Refer to the

ET002: none
request interpretation of ET002
Refer to the
ET003: Internal battery none
Locating system Refer to the

ET004: none
ACCESS/ active interpretation of ET004
SAFETY
Refer to the
ET005: Tracker active none
Refer to the
ET006: SIM card none
In the event of a fault,

apply the interpretation
PR001 Battery charge none
of fault DF004 Battery
internal fault.
SVT_V04_CCONF
MR-366-X84-82A050$075.mif
V3
82A-20
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Status summary table
Tool status Diagnostic tool title
ET001 SVT operational

ET002 System activation request
ET003 Internal battery
ET004 Locating system active
ET005 Tracker active
ET006 SIM card
MR-366-X84-82A050$080.mif
V3
82A-21
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Interpretation of statuses
ET001 SVT OPERATIONAL
YES: indicates that the anti-theft tracking unit is operational

STATUS DEFINITION
NO: indicates that the anti-theft tracking unit is not operational

AFTER REPAIR
SVT_V04_ET001
MR-366-X84-82A050$090.mif
V3
82A-22
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
ET002 SYSTEM ACTIVATION REQUEST
ACTIVE: indicates that system activation was requested.

STATUS DEFINITION
INACTIVE: indicates that system activation was not requested.

AFTER REPAIR
SVT_V04_ET002
MR-366-X84-82A050$090.mif
V3
82A-23
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
ET003 INTERNAL BATTERY
OK: indicates that the battery is in good condition

STATUS DEFINITION
NOK: indicates that the battery is not in good condition

AFTER REPAIR
SVT_V04_ET003
MR-366-X84-82A050$090.mif
V3
82A-24
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
ET004 LOCATING SYSTEM ACTIVE
YES: indicates that the locating system is active

STATUS DEFINITION
NO: indicates that the locating system is not active

AFTER REPAIR
SVT_V04_ET004
MR-366-X84-82A050$090.mif
V3
82A-25
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
ET005 TRACKER ACTIVE
YES: indicates that the tracker is active

STATUS DEFINITION
NO: indicates that the tracker is not active

AFTER REPAIR
SVT_V04_ET005
MR-366-X84-82A050$090.mif
V3
82A-26
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
ET006 SIM CARD
PRESENT: indicates the presence of the SIM card

STATUS DEFINITION
ABSENT: indicates the absence of the SIM card

AFTER REPAIR
SVT_V04_ET006
MR-366-X84-82A050$090.mif
V3
82A-27
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Parameter summary table
Tool Parameter Diagnostic tool title
PR001 Battery charge
MR-366-X84-82A050$095.mif
V3
82A-28
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Interpretation of parameters
SWITCH ON THE VEHICLE + AFTER IGNITION FEED.

PR001
NOTES This parameter indicates the internal voltage of the battery.
NOTES None.
The value of PR001 must be between 3.5 V  PR001  4.5 V.

AFTER REPAIR
SVT_V04_PR001
MR-366-X84-82A050$096.mif
V3
82A-29
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Customer complaints
Only refer to the customer complaints after performing a complete check using the
NOTES
diagnostic tool.
NO DIALOGUE WITH THE COMPUTER ALP1
MR-366-X84-82A050$100.mif
V3
82A-30
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
Fault finding – Fault finding chart
ALP1 NO DIALOGUE WITH THE COMPUTER
Switch on the vehicle + after ignition feed.
NOTES
Use the Wiring Diagrams Technical Note for LOGAN, SANDERO, DUSTER,
MEGANE II ph1 and ph2, SCENIC II, MASTER II ph2 and ph3, THALIA 2/SYMBOL
2, CLIO II F6, KANGOO VLL.
Ensure that the diagnostic tool is not the cause of the fault by using it to establish dialogue with a
computer on another vehicle. If the diagnostic tool is not causing the fault and dialogue cannot be established
with any other computer on the same vehicle, it may be that a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations to obtain the correct
voltage (12 V < X < 15 V).
Check the condition of the fuses in the passenger compartment fuse and relay box, component code 260 for
MEGANE II ph1 and ph2, SCENIC II, KANGOO VLL or component code 1016 for LOGAN, SANDERO, DUSTER,
MASTER II ph2 and ph3, THALIA 2/SYMBOL 2, CLIO II F6.
Check the connection of the anti-theft tracking unit connector, component code 2186.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.

AFTER REPAIR
SVT_V04_ALP001
MR-366-X84-82A050$110.mif
V3
82A-31
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
ALP1
CONTINUED 1
For MEGANE II and SCENIC II, check the connection of the Protection and Switching Unit connector, component
code 1337.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
For CLIO II F6, check the connection of the UCH connector, component code 645.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, insulation and the absence of interference resistance on the following connections:
For LOGAN, SANDERO, DUSTER, THALIA 2/SYMBOL 2, CLIO II F6:

– BP56 between components 2186 and 1016 (+ before ignition feed),
– AP10 between components 2186 and 1016 (+ after ignition feed),
– NC of component 2186 (for SANDERO and LOGAN).
– N of component 2186 (for THALIA 2/SYMBOL 2 and CLIO II F6)
– BP56 between components 2186 and 645 (for Clio II F6)

– MAN of component 2186.

AFTER REPAIR
MR-366-X84-82A050$110.mif
V3
82A-32
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
ALP1
CONTINUED 2
For MASTER II:

– BP between components 2186 and 1016 (+ before ignition feed),
– AP between components 2186 and 1016 (+ after ignition feed),
– Earth of component 2186.
For KANGOO VLL:

– BP3 and BP10 between components 2186 and 260 (+ before ignition feed),
– NA of component 2186.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.

AFTER REPAIR
MR-366-X84-82A050$110.mif
V3
82A-33
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
ALP1
CONTINUED 3
Check that the anti-theft tracking unit, component code 2186, is correctly supplied on the following connections:
For LOGAN, SANDERO, DUSTER, THALIA 2/SYMBOL 2, CLIO II F6:

– BP56 on component 2186 (+ before ignition feed),
– AP10 on component 2186 (+ after ignition feed).

For MASTER II:

– BP on component 2186 (+ before ignition feed),
– AP on component 2186 (+ after ignition feed).
For KANGOO VLL:

– BP3 and BP10 between components 2186 and 260 (+ before ignition feed),
If the fuses are faulty in the passenger compartment fuse and relay box, component code 260 for MEGANE II,
SCENIC II and KANGOO VLL or component code 1016 for LOGAN, SANDERO, DUSTER, MASTER II, THALIA
2/SYMBOL 2, CLIO II F6, replace them.

AFTER REPAIR
MR-366-X84-82A050$110.mif
V3
82A-34
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
ALP1
CONTINUED 4
Check the continuity and insulation of the following connections:

– NC (left-hand drive) or MAM and NC (right-hand drive) of component 225.

– MAM and NAM of component 225.
For MASTER II:

– BCP3 between components 225 and 1016 (+ before ignition feed),
– NC and MQ (left-hand drive) or NJ and MQ (right-hand drive) of component 225.
For THALIA 2/SYMBOL 2 and CLIO II F6:

– N and M of component 225.
For KANGOO VLL:

– MK and NA of component 225.

AFTER REPAIR
MR-366-X84-82A050$110.mif
V3
82A-35
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
ALP1
CONTINUED 5
Check the continuity and insulation of the following connection:

• HK between components 225 and 2186.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check that the diagnostic socket, component code 225, is correctly supplied by checking the following
connections:


For MASTER II:

– BCP3 on component 225 (+ before ignition feed),

AFTER REPAIR
MR-366-X84-82A050$110.mif
V3
82A-36
SVT
ENGINE IMMOBILISER
82A
Vdiag No.: 04
ALP1
CONTINUED 6
For THALIA 2/SYMBOL 2, CLIO II F and KANGOO VLL:

If dialogue is still not established after these various checks, replace the anti-theft tracking unit, component code
2186.
If the fault is still present, contact Techline.

AFTER REPAIR
MR-366-X84-82A050$110.mif
V3
82A-37

007 Megane

Uploaded by

Copyright:

Available Formats

007 Megane

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

007 Megane

Uploaded by

Copyright:

Available Formats

8 Electrical equipment

Fault finding – Introduction 82A - 2

© Renault s.a.s. 2013

Fault finding – Introduction

1. SCOPE OF THIS DOCUMENT

Vehicle(s): LOGAN, SANDERO, DUSTER,

Function concerned: Anti-Theft Tracking Unit Vdiag No.: 04

2. PREREQUISITES FOR FAULT FINDING

Type of diagnostic tools

Special tooling required

Special tooling required

Elé. 1681 Universal bornier

*VLL — Very Long Life

Fault finding – Introduction

SCENIC II and MEGANE II:

Switch on the forced + after ignition feed:

Switching off the forced + after ignition feed:

For vehicles with key/radiofrequency remote control unit,

Fault finding – Introduction

If the fault is not confirmed, check:

– the electrical lines which correspond to the fault,

Customer complaints - Fault finding chart

Fault finding – Introduction

5. FAULT FINDING PROCEDURE

Perform a pre-diagnostic on the

Print the system fault finding log

Deal with present faults The cause is

Fault finding – Introduction

5. FAULT FINDING PROCEDURE (continued)

Fault finding problems

Inspection of each component

If a fault is detected, repair or replace the wiring harness.

Fault finding – Introduction

6. FAULT FINDING LOG

IT IS THEREFORE COMPULSORY TO COMPLETE A FAULT FINDING LOG

You will always be asked for this log:

Instructions to be followed before opening of the fuel circuit

Instructions to be followed during the operation

Fault finding – List and location of components

For MEGANE II and SCENIC II:

For LOGAN, SANDERO and DUSTER:

The anti-theft tracking unit (computer) consists of:

– An integrated GPS aerial to locate the vehicle.

– An integrated GSM aerial to communicate with a call centre.

Fault finding – Features

For MEGANE II and SCENIC II:

The computer has several operating modes:

Fault finding – Configurations and programming

VP001 Enter VIN

Procedure for writing the VIN

RZ001: Clear faults

CF001: CONFIGURE SVT

Fault finding – Replacement of components

Procedure to be applied before repair:

Procedure to be applied after repair:

Fault finding – Fault summary table

DF001 9A01 External GPS aerial

DF003 9A03 GSM internal error

DF004 9A05 Battery internal fault

DF005 9A09 SVT internal fault