Renault
Renault
Renault
WIPERS - WASHERS
85A
UCH
Vdiag No.: 08
V2 Edition Anglaise
"The repair procedures given by the manufacturer in this document are based on the All rights reserved by Renault s.a.s.
technical specifications current when it was prepared.
Copying or translating, in part or in full, of this document or use of the service part
The procedures may be modified as a result of changes introduced by the reference numbering system is forbidden without the prior written authority of
manufacturer in the production of the various component units and accessories from Renault s.a.s.
which his vehicles are constructed."
This document presents the fault finding method applicable to all computers with the following specifications:
Documentation type
Fault finding procedures (this document):
– Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
– Visu - Schéma.
Diagnostic tool
Multimeter
If the information obtained by the fault finding tool requires the electrical continuity to be checked, connect bornier
Elé. 1622 or universal bornier Elé. 1681.
WARNING:
– All tests with bornier Elé. 1622 or Elé. 1681 must be conducted with the battery disconnected.
– The bornier is only designed to be used with a multimeter. Never supply the test points with 12 V.
UCHL35_V08_PRELI
MR-425-X35-85A000$010.mif
V2
85A-2
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
3. SAFETY INSTRUCTIONS
The safety instructions must be followed at all times when working on components, to avoid damage or injury:
– check the battery voltage to avoid incorrect operation of computer functions,
– use the proper tools.
MR-425-X35-85A000$010.mif
V2
85A-3
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
3
6
4
1
2
3 Combined wiper-washer
MR-425-X35-85A000$020.mif
V2
85A-4
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Combined wiper-washer:
The role of the combined wiper-washer control is to control the various washing and wiping functions.
UCH:
The UCH is used to manage all wiper functions (activation, wiper speed, etc).
MR-425-X35-85A000$030.mif
V2
85A-5
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
645 UCH
14A
M
14B
14D
16A 221
AP7 AP7
MR-425-X35-85A000$040.mif
V2
85A-6
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Windscreen washing/wiping
The UCH receives the wiper speed, windscreen wiper park and windscreen washing-wiping information.
This provides the following functions:
– intermittent wiper speed,
– extended wiper time after washing,
– return to park position.
In the park position, the switch is closed to earth, and the UCH receives logical information 0.
Detection of the park position should be made on transition and not level, that is, if the wiper stalk is moved from the
intermittent position to the park position while the wiper blade is in the park position and the wiper motor is running,
it will not be stopped until the next reading of the park position. This condition is necessary in order to obtain an exact
park position.
Intermittent
The intermittent wiper speed function is only active if the + after ignition is present and if the switch is in the
intermittent position.
The time delay between two wipes is 5 seconds, and this cannot be modified by the diagnostic tool.
When the windscreen intermittent speed function is activated, the windscreen intermittent speed relay is held by the
UCH until the park position is detected. When the intermittent speed time delay has elapsed, the relay is held again
and the cycle begins again.
The UCH does not manage the windscreen washer pump control, it only processes the incoming windscreen washer
command to provide screen wiping and the extended wiper time after washing.
After the washer pump is activated, the first wiping is performed after a time delay of 750 ms.
When the washing control is pressed briefly, the windscreen wiper performs 1 wiping cycle.
When the washing control is pressed for longer, the UCH activates the windscreen wiper throughout the washing
phase. At the end of the washing phase, the UCH counts the status changes of the park position in order to stop the
extended wiping phase.
MR-425-X35-85A000$050.mif
V2
85A-7
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Equipment required:
Configuration
Name of configuration Option Configuration
reading
MR-425-X35-85A000$060.mif
V2
85A-8
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
MR-425-X35-85A000$070.mif
V2
85A-9
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Read configuration LC064 Rear screen wiper and check that the vehicle is configured WITHOUT
(see Configurations).
If this is not the case, configure the computer.
UCHL35_V08_DF040P
MR-425-X35-85A000$080.mif
V2
85A-10
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Special note:
Use the Wiring Diagram Technical Note Thalia 2 / Symbol 2.
Check that the windscreen park position status ET027 Windscreen park position is ACTIVE each time the wiper
blade arrives at the park position and then changes back to INACTIVE.
Check the connection and condition of the UCH connectors, component code 645.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance of the following connections:
14L between components 645 and 212,
M between component 212 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the connection and condition of the windscreen wiper motor connector, component code 212.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the operation and fitting of the windscreen wiper motor.
The windscreen wiper motor may need to be replaced (see MR 423 Mechanical, 85A, Wiping - Washing,
Windscreen wiper motor: Removal - Refitting).
UCHL35_V08_DF097
MR-425-X35-85A000$080.mif
V2
85A-11
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Only carry out this conformity check after a complete check using the diagnostic tool.
NOTES The values shown in this conformity check are given as a guide.
Test conditions: Engine stopped, ignition on.
MR-425-X35-85A000$090.mif
V2
85A-12
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
MR-425-X35-85A000$100.mif
V2
85A-13
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Special note:
Use the Wiring Diagram Technical Note Thalia 2 / Symbol 2.
Check the presence and condition of fuse F21 (15 A) in the passenger compartment
"ABSENT" fuse box, component code 1016 (see MR 423 Mechanical, 81C, Fuses, Fuses: List
and location of components).
Check the condition and connection of the UCH connector, component code 645
(tabs bent, broken, etc.).
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the + 12 V after ignition feed on connection AP9 of the combined wiper-
washer, component code 145.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
MR-425-X35-85A000$110.mif
V2
85A-14
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
ET492
CONTINUED
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
MR-425-X35-85A000$110.mif
V2
85A-15
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Special note:
Use the Wiring Diagram Technical Note Thalia 2 / Symbol 2.
Check the presence and condition of fuse F7 (20 A) in the passenger compartment
ET558
fuse box, component code 1016 (see MR 423 Mechanical, 81C, Fuses, Fuses: List
"NO"
and location of components).
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
UCHL35_V08_ET558
MR-425-X35-85A000$110.mif
V2
85A-16
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
ET558
CONTINUED
If the status is YES, and that the windscreen wiper motor does not turn intermittently,
check the connection and condition of the combined wiper-washer connector,
component code 145, UCH connector, component code 645 and the windscreen wiper
ET558
motor connector, component code 212.
"YES"
If the connector or connectors are faulty and if there is a repair procedure (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
MR-425-X35-85A000$110.mif
V2
85A-17
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Tool
Diagnostic tool title Comments
command
MR-425-X35-85A000$120.mif
V2
85A-18
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Special note:
Use the Wiring Diagram Technical Note Thalia 2 / Symbol 2.
Check the presence and condition of fuse F7 (20 A) in the passenger compartment fuse box, component code
1016 (see MR 423 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the windscreen wiper connector, component code 212 and the combined
wiper-washer connector, component code 145.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the + 12 V after ignition feed on connection AP7 of the combined washer/wiper, component code 145.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIR Carry out a road test and then a check using the diagnostic tool.
UCHL35_V08_AC056
MR-425-X35-85A000$130.mif
V2
85A-19
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Only consult these customer complaints after a complete check with the
NOTES
diagnostic tool.
WIPERS - WASHERS
MR-425-X35-85A000$140.mif
V2
85A-20
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Only consult this customer complaint after a complete check with the diagnostic
tool.
There must be no present or stored faults.
NOTES
Special note:
Use the Wiring Diagram Technical Note Thalia 2 / Symbol 2.
Check the presence and condition of fuse F7 (20 A) in the passenger compartment fuse box, component code
1016 (see MR 423 Mechanical, 81C, Fuses, Fuses: List and Location of components).
Check the + 12 V after ignition feed on connection AP7 of the combined screen wiper-washer, component code
145.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check that the motor operates correctly.
UCHL35_V08_ALP04
MR-425-X35-85A000$150.mif
V2
85A-21
UCH
WIPERS - WASHERS
85A
Vdiag No.: 08
Only consult this customer complaint after a complete check with the diagnostic
tool.
There must be no present or stored faults.
NOTES
Special note:
Use the Wiring Diagram Technical Note Thalia 2 / Symbol 2.
Check the presence and condition of fuse F7 (20 A) in the passenger compartment fuse box, component code
1016 (see MR 423 Mechanical, 81C, Fuses, Fuses: List and Location of components).
Check the + 12 V after ignition supply on connection AP7 of the stalk, component code 145.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check that the motor operates correctly.
UCHL35_V08_ALP05
MR-425-X35-85A000$150.mif
V2
85A-22