artec 300 series

ARTEC-320 Two way, double 10”

Installation Line Array

» Two way passive system

» 2 x 10” (2.5” VCD)

» 1 x M-75 compression
driver (3” VCD)

» Aluminium Waveguide

» Top grade Birch cabinet

construction
ISO-flex polyurea paint

» Rigging hardware for

permanent installation
compatible with the ARTEC-322S

The ARTEC-320 system is a two-way line array system for The impedance of the system is 16 ohm, due to the use of 8
installation with dual 10" low frequency speakers, and a ohm speakers in series and the design of the passive
compression driver with 3" titanium diaphragm and 1.5” crossover, which optimizes the horizontal coverage in the
frequency bandwidth near the X-over point.
exit for the high frequency reproduction.
The JP-320 (included in ARTEC-320) are accessories that
The 15mm birch plywood cabinet construction offers an permit the system array assembly, whereas the AX-AR3
ultra-compact design which is available in black or white. (optional) is needed for the rigging system.

The high frequency waveguide is the same as the The system´s width is the same as the ARTEC-322S, so a
waveguide incorporated in the prestigious event series. cluster with subwoofers can be installed by the use of the
same accessories JP-320.

Technical Specifications Dimensions

Peak Power Handling 2000 W
RMS (Average) Power Handling 1 500 W
Frequency Range (-10dB) 60 Hz - 20 kHz
Nominal Impedance 16 ohms
On-axis Sensitivity 1 W / 1 m 99 dB SPL
2
Maximum Peak SPL at 1 m 132 dB
HF Horn Coverage Angles (-6dB) 90º x Splay Dependent
Enclosure Material Birch Plywood
Color / Finish Black or White FX fiberglass paint
Transducers / Replacement Parts LF: 2 x 10MI/GM-10MI
HF: M-75/GM-M75N

Connectors Terminal Strip

Dimensions (H x W x D) 27 x 70 x 36 cm
10.6 x 27.6 x 14.2 in

Weight 26.5kg (58.3 lb)

Accessories AX-AR3 / AX-AR3-W
JP-320 / JP-320-W

Notes:

1. Based on a 2 hour test continuously applying 6dB crest factor pink noise.
2. Maximum calculated Peak SPL based on sensitivity and RMS pòwer handling.
ARTEC-320
120.0

Frequency Response dBSPL

110.0

Shows the frequency

response (processed) at 1 100.0

m of a unit radiating to
an anechoic environment 90.0

and driven by a 4 V
swept sine wave signal. 80.0

70.0
10 100 1k 10k Hz 20k

-180 0

Horizontal Directivity dB
-120
-10

Shows normalized
horizontal isobar plot. -60

-20

-30

60

-40
120

180 -50
100 1 k 10 k 12k5 Hz

-180 0

Vertical Directivity dB
-120
-10

Shows normalized
vertical isobar plot. -60

-20

-30

60

-40
120

180 -50
100 1 k 10 k 12k5 Hz

6 down 6 up
Polar Response dB dB
-30° 30° -30° 30°
0 0

Shows the 1/3 octave 250Hz

-6 -6
band horizontal (left) 500Hz

and vertical (right) 1000Hz

2000Hz
-60°
-12
60° -60°
-12
60°

polars for the indicated 4000Hz

-18 -18
frequencies. Full scale 8000Hz

is 30 dB, 6 dB per 12500Hz

-24 -24

division. -90° 90° -90° 90°

-120° 120° -120° 120°

-150° 150° -150° 150°

180° 180°

Ref 0 1/3 Octave Ref 0 1/3 Octave

Recommended processor settings (DAS DSP-2060A or DSP-4080)

High Pass Filter Butterworth 24dB/oct at 90 Hz

Low Pass Filter ----
Limiter 400 W RMS; Threshold +8dBu (32dB amplifier Gain), peak limiter +11dBu, 8ms attack time, release x 16
EQ (1 cabinet FLAT response) 3k43Hz Q7 -3dB, 2k47Hz High Shelving Q0.71 -2dB, 8k81Hz Q3 -7dB

NOTES. 1.Frequency response: referred to 1 m; low end obtained through the use of near field techniques; Product improvement through r esearch and development
one-third octave smoothed for correlation with human hearing. 5.Polars were acquired by placing the unit on is a continuous process at D.A.S. Audio. All specifications
a computer controlled turntable inside our anechoic chamber. Measurement distance was 4 m. subject to change without notice.