Sx19v007 Zza Hitachi
Sx19v007 Zza Hitachi
Sx19v007 Zza Hitachi
Accepted by : Proposed by :
Sh.
Displays, Hitachi, Ltd. 3284PS 2701 -SX19V007-ZZA - 5 Page 1-1/1
No.
RECORD OF REVISIONS
Displays, Sh.
Date Aug. 2, 2000 3284PS 2702 -SX19V007-ZZA - 5 Page 2-1/1
Hitachi, Ltd. No.
3. GENERAL DATA
Displays, Sh.
Date Aug. 2, 2000 3284PS 2703 -SX19V007-ZZA - 5 Page 3-1/1
Hitachi, Ltd. No.
4. ABSOLUTE MAXIMUM RATINGS
4. 1 ELECTRICAL ABSOLUTE MAXIMUM RATINGS (LCM) VSS=0V:Standard
ITEM SYMBOL MIN MAX UNIT COMMENT
Pow er Supply for Logic VDD-VSS 0 7.0 V
Contrast Adjustment Voltage VCON-VSS 0 VDD V
Input Voltage Vi -0.3 VDD+0.3 V Note 1
Input Current Ii 0 1 A
Static Electricity - - - - Note 2
Note 1 DISP•OFF, FLM, CL1, CL2, D0∼D7
Note 2 Please ensure you are grounded w hen handling LCM
Displays, Sh.
Date Aug. 2, 2000 3284PS 2704 -SX19V007-ZZA - 5 Page 4-1/1
Hitachi, Ltd. No.
5. ELECTRICAL CHARACTERISTICS
5. 1 ELECTRICAL CHARACTERISTICS OF LCD VSS=0V
ITEM SYMBOL CONDITION MIN TYP MAX UNIT
Q - 50 -
Pow er Supply Current
(Note 3)(Note 4) IDD VDD-VSS=3.3V mA
CF - 80 120
(Note 1) The brightness w ill increase w ith decreasing contrast adjustment voltage.
(Note 2) DISP•OFF, FLM, CL1, CL2, D0∼D7
(Note 3) fFLM=100Hz, Ta=25°C, "Q" test pattern(Q) and Checker pattern(CF) used as Display
pattern.
(Note 4) Rush Current at Pow er ON : 2A(PK) × 100µs
(Note 5) VCON
(Note 6) The Contrast Adjustment Voltage is specified as 1.8±0.3V under the condition, that
optimum contrast is obtained by naked eyes w ith a "Q" test pattern.
fFLM=100Hz, 1/497Duty
(Note 7) Please set the frame frequency so as to avoid flicker and rippling on the display.
(Note 8) The CFL cable has the follow ing absolute maximum ratings.
VCFL side : 2kV
VSS side : 300V
This CFL inverter shall not exceed the specified voltage.
(Note 9) Some points for attention w hile setting the driving condition of an appliance.
(1) Frame Frequency
Please set the frame frequency as the typical value (central value) w hich is show n in
CAS. According to the characteristic of response time of LC material, that setting the
frame frequency near the minimum value or under the minimum value show n in CAS w ill
cause a frame w ith moving phenomenon.
(2) Setting value of Vcon
Vcon, adjusted to get the best contrast ratio of LCD module, is adjusted to be distributed
w ithin the tolerance ±0.3V of central value in CAS before LCD modules ship the factory.
The below items are recommended at customer side.
(i) When designing the appliance, please set the Vcon value as an adjustable value.
(ii) And the Vcon value must be able to be adjusted to match the most suitable Vcon to
get the best contrast ratio. A fixed Vcon value is usually a little different from the
most suitable Vcon value of LCD module and causes a misjudgment.
(iii)The Vcon adjustment (w hen D/A [Digital/Analogue] converter is used) is
recommended to be set as 50mV at most per step. That one step is more than 50mV
may cause the input value to be not able to match the most suitable value.
The characteristic of contrast ratio can not present absolutely.
Displays, Sh.
Date Aug. 2, 2000 3284PS 2705 -SX19V007-ZZA - 5 Page 5-1/3
Hitachi, Ltd. No.
5. 2 ELECTRICAL CHARACTERISTICS OF TOUCH PANEL
5.2.1 OPERATING CONDITION
ITEM SPECIFICATION
X 1.5% max
Linearity See Note 1
Y 1.5% max
Displays, Sh.
Date Aug. 2, 2000 3284PS 2705 -SX19V007-ZZA - 5 Page 5-2/3
Hitachi, Ltd. No.
Note 1 : Test Method and Conditions
The difference ("e") betw een the theoretical output voltage and the actual output voltage w hen
pressure is applied to any point w ithin the valid area must be as indicated below .
e < applied voltage × 0.03 (=±0.015)
E(v)
Resistor
Eb Dashed line :
XL Theoretically
Ag electrode Ag electrode
correct voltage
X
e Solid line :
rA rB Ea Output voltage
Valid area
XL min
(same Y line)
E XL max
VCFL GND
A
INVERTER
(Note 7) We recommend to equip protection circuit (To stop output) w hich w orks under abnormal
operation to the inverter for CFL.
Displays, Sh.
Date Aug. 2, 2000 3284PS 2705 -SX19V007-ZZA - 5 Page 5-3/3
Hitachi, Ltd. No.
6. OPTICAL CHARACTERISTICS
6.1 OPTICAL CHARACTERISTICS OF LCD Ta=25°C (Backlight On)
ITEM SYMBOL CONDITION MIN TYP MAX UNIT NOTE
x - (0.31) - -
Green
y - (0.51) - -
φ=0°, θ=0° 7)
x - (0.16) - -
Blue
y - (0.14) - -
x - (0.28) - -
White
y - (0.30) - -
Displays, Sh.
Date Aug. 2, 2000 3284PS 2706 -SX19V007-ZZA - 5 Page 6-1/3
Hitachi, Ltd. No.
Note 1. Definition of θ and φ Note 3. Definition of contrast "K"
(Normal) Brightness of selected area (B1)
View ing direction K=
Brightness of non-selected area (B2)
Z
φ1 φ2 (B1)
y (θ=180°) B1 (Di="H")
(B2)
X X' (Di="L")
θ B2
y' (θ=0°)
Operation voltage
Note 2. Definition of view ing angle φ1 and φ2
K φ
φ1<0°<φ2
φ=0°
2.0
Sensor
Back light
φ1 φ2
Sensor : BM-7 or similar equipment
Contrast ratio K vs view ing angle φ
10% 90%
tr tf
Note. 7 The LCD driving voltage should be adjusted as to obtain maximum contrast.
Displays, Sh.
Date Aug. 2, 2000 3284PS 2706 -SX19V007-ZZA - 5 Page 6-2/3
Hitachi, Ltd. No.
6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT
P1 P4 P7
X=60
P2 P5 P8
X=240
P3 P6 P9
X=420
Displays, Sh.
Date Aug. 2, 2000 3284PS 2706 -SX19V007-ZZA - 5 Page 6-3/3
Hitachi, Ltd. No.
7. BLOCK DIAGRAM
Timing M
CN3
Buffer Circuit
FLM Timing DISP•OFF
Circuit
CL1
CL2
DISP•OFF
Buffer
D7~D0 X1
Note1
TS1 LCD PANEL
Temperature
TS2 Sensor
X480
VDD
Pow er
VSS Supply
VCON Circuit
DIG Y2
Y2
DIG X1
X1 Touch Panel X2
DIG Y1
DIG X2 Y1
VSS
VCFL
CFL
CN7
Note1; TDK NTCC20124CH104KCT
Displays, Sh.
Date Aug. 2, 2000 3284PS 2707 -SX19V007-ZZA - 5 Page 7-1/1
Hitachi, Ltd. No.
8. INTERFACE TIMING DIAGRAM
8.1 TIMING CHART
CL1
CL2
Dummy data X1 X2
D7 R B G
Y1 Y9 Y1917
D6 G R B
Y 2 Y10 Y1918
D1 R B G
Y 7 Y15 Y1919
D0 G R B
Y 8 Y16 Y1920
FLM
(Reduction) Note (1)
CL1
(480+n) × T
FLM
Note (1) : The blanking interval w hen s w itching lines should be equal to the interval betw een
tw o CL1 pulses.
Displays, Sh.
Date Aug. 2, 2000 3284PS 2708 -SX19V007-ZZA - 5 Page 8-1/6
Hitachi, Ltd. No.
8.2 INTERFACE TIMING SPECIFICATION
tFH
tFS
FLM
tWHCL1
tr tf
CL1
CL2
tDSU tCYC
tDH
DO~D7
0.9VDD 0.9VDD
0.8VDD 0.8VDD
MEASUREMENT POINT
0.2VDD 0.2VDD
0.1VDD 0.1VDD
Displays, Sh.
Date Aug. 2, 2000 3284PS 2708 -SX19V007-ZZA - 5 Page 8-2/6
Hitachi, Ltd. No.
8.3 POWER ON / OFF SEQUENCE
tDLD tDLD
0.95×VDD 0.95×VDD
VDD 0.05×VDD
tCH tLDH tLDH tCH
tD
0.8×VDD 0.8×VDD
CL1
(Note 1) Please keep the specified sequence. Using other than recommended sequence
may cause permanent damage to the LCD panel.
(Note 2) Please use DISP•OFF function. Sw itching by other than the DISP•OFF function
may cause display deterioration.
(Note 4) Please keep the specified sequence of DISP•OFF signal because if the tVH is
short enough, LCD panel may not be restarted.
Displays, Sh.
Date Aug. 2, 2000 3284PS 2708 -SX19V007-ZZA - 5 Page 8-3/6
Hitachi, Ltd. No.
8.4 POWER SUPPLY FOR LCM
R1
CFL
Stabilized +
VR VCON VCFL
+3.3V C1
-
R2
VSS
LCM
VDD
+
+3.3V C2
-
VSS
Displays, Sh.
Date Aug. 2, 2000 3284PS 2708 -SX19V007-ZZA - 5 Page 8-4/6
Hitachi, Ltd. No.
8.5 INPUT DATA ALLOCATION TABLE
D D D D D D D D D D D D D D D D D
Data Signal -----
7 6 5 4 3 2 1 0 7 6 5 4 4 3 2 1 0
1 2 3 4 5 6 7 8 9 10 11 12 1 1 1 1 1
Y
----- 9 9 9 9 9
1 1 1 1 2
X 6 7 8 9 0
1 R G B R G B R G B R G B ----- G B R G B
2 R G B R G B R G B R G B ----- G B R G B
3 R G B R G B R G B R G B ----- G B R G B
4 R G B R G B R G B R G B ----- G B R G B
5 R G B R G B R G B R G B ----- G B R G B
478 R G B R G B R G B R G B ----- G B R G B
479 R G B R G B R G B R G B ----- G B R G B
480 R G B R G B R G B R G B ----- G B R G B
R : RED
G : GREEN
B : BLUE
Displays, Sh.
Date Aug. 2, 2000 3284PS 2708 -SX19V007-ZZA - 5 Page 8-5/6
Hitachi, Ltd. No.
8.6 INTERNAL PIN CONNECTION
CN3 MOLEX 52435-2891
PIN No. SIGNAL LEVEL FUNCTION
1 TS2 - Temperature Sensor PIN2
2 TS1 - Temperature Sensor PIN1
3 VSS - GND
4 Vcon - Contrast Adjustment Voltage
5 VSS - GND
6 VDD - Pow er Supply for Logic
7 VDD - Pow er Supply for Logic
8 DISP•OFF H/ L H : ON / L : OFF
9 D7
10 D6
11 D5
12 D4
H/ L Display Data
13 D3
14 D2
15 D1
16 D0
17 VSS - GND
18 CL2 H/ L Data Shift
19 VSS - GND
20 CL1 H/ L Data Latch
21 VSS - GND
22 FLM H First Line Marker
23 VSS - GND
24 VSS - GND
25 DIGY2 - Touch panel Y2
26 DIGX1 - Touch panel X1
27 DIGY1 - Touch panel Y1
28 DIGX2 - Touch panel X2
Displays, Sh.
Date Aug. 2, 2000 3284PS 2708 -SX19V007-ZZA - 5 Page 8-6/6
Hitachi, Ltd. No.
10. APPEARANCE STANDARD
10.1 APPEARANCE INSPECTION CONDITION
Visual inspection should be done under the follow ing condition.
eye eye
25° 25°
LCD
Bezel
B zone : Area betw een the effective display area line and the dots area (A zone) line
specified on page 9-1/2 of this document.
Dots area
Displays, Sh.
Date Aug. 2, 2000 3284PS 2710 -SX19V007-ZZA - 5 Page 10-1/4
Hitachi, Ltd. No.
10.3 APPEARANCE SPECIFICATION
(1) LCD APPEARANCE
*) If any problem related to this section occurs, both parties (Customer and HITACHI) shall
discuss the matter in detail.
Displays, Sh.
Date Aug. 2, 2000 3284PS 2710 -SX19V007-ZZA - 5 Page 10-2/4
Hitachi, Ltd. No.
No. ITEM CRITERIA APPLIED
ZONE
Contrast irregularity Average Maximum
Minimum
diameter Contrast acceptable space
(Spot) D (mm) number
D<0.25 ignored
L To be A
0.25<D<0.35 10 20mm
judged by
0.35<D<0.5 HITACHI 4 20mm
0.5<D<0.7 STANDARD 3 50mm
0.7<D none
C
Contrast irregularity Width Length Maximum
acceptable Minimum
(Line) W (mm) L (mm) number space
(A pair of scratches) W < 0.25 L < 1.2 2 20mm
D W < 0.2 L < 1.5 3 20mm A
W < 0.15 L < 2.0 3 20mm
W < 0.1 L < 3.0 4 20mm
The w hole number 6
Displays, Sh.
Date Aug. 2, 2000 3284PS 2710 -SX19V007-ZZA - 5 Page 10-3/4
Hitachi, Ltd. No.
(3) TOUCH PANEL APPEARANCE
b
Glass chipping a
Note (1) Definition of Average diameter (D) Note (2) Definition of Length (L) and Width (W)
L
b
a+b
D=
2
Displays, Sh.
Date Aug. 2, 2000 3284PS 2710 -SX19V007-ZZA - 5 Page 10-4/4
Hitachi, Ltd. No.
11. PRECAUTION IN DESIGN
11. 1 MOUNTING PRECAUTIONS
Please mount the LCD Module by using mounting holes provided. While mounting please pay attention
to the follow ings.
Protective spacer
Example of mounting
191±0.2
(95.5)
(17.0) (20.0)
Upper panel
Protective spacer
4-φ5.0
Low er panel
Spacer 4-φ7.0
(95.5) Unit : mm
Scale : NTS
Location of spacers
(1) To prevent the module cover from being pressed, the distance betw een the module and the
fitting plate, w hich means the length of the spacers, should be shorter than 1.0mm.
(2) The use of protective spacers are recommend in order to protect the module from shock.
(3) For the module to be used at upright position, the case shall have a structure w here the touch
panel screen does not shift w ith its ow n w eight.
Displays, Sh.
Date Aug. 2, 2000 3284PS 2711 -SX19V007-ZZA - 5 Page 11-1/4
Hitachi, Ltd. No.
(4) When assembling the touch panel and your case, please refer to the figure below .
(>2.0) Effective area
Cushion Insulated area Transparent area
Case opening
Case
Tape
Touch panel
Case LCM
(5) The clearance betw een the touch panel and the case shall be designed so that the case edge
never presses the input screen w hen it is deformed by heat or other causes.
(6) The case shall be designed not to touch the tail portion (FPC for touch panel).
(7) The boundary space betw een the effective area and the insulated area is unstable.
Touching this area may effect the operation of the touch panel.
The case must be designed so that it does not touch the boundary space.
(2) As the adhesives used for attaching the upper/low er polarizers and aluminum plate are made
from organic substances w hich w ill be deteriorated by a chemical reaction w ith such chemicals
as acetone, toluene, ethanol and isopropylalcohol. For cleaning normal hexane is recommended.
Please contact Hitachi in case you need to use chemicals other than the above.
Displays, Sh.
Date Aug. 2, 2000 3284PS 2711 -SX19V007-ZZA - 5 Page 11-2/4
Hitachi, Ltd. No.
(3) For cleaning lightly w ipe the dirty surface w ith absorbent cotton or other soft material like chamois,
soaked in the recommended chemicals w ithout scrubbing it hardly.
Alw ays w ipe the surface horizontally or vertically. Never w ipe in circles. To prevent the display
surface from being damage, it is normally sufficient, to w ipe it w ith absorbent cotton.
(4) Immediately w ipe off saliva or w ater drop from the display area because it may cause
deformation or fading of the colors.
(5) Fogy dew deposited on the display surface may cause damage, to the polarizer.
In case the display has stored at low temperatures, please allow the display to w arm up to room
temperature before taking it out of its compartment.
(6) Please do not touch the display area or I/F pins barehanded because it may cause stains on the
display area or shorts betw een terminals. Please be aw are that some cosmetics are detrimental to
polarizers.
(7) Please take caution w hen handling the LCM so as not cause cracks or chips chipped to the LCD
glass. Please do not apply any shock to the LCM since the glass may break.
(8) Please keep maximum pressure to the display surface to less than 1.96×104 Pa.
In case the pressure area is less than 1cm2, maximum pressure must be less than 1.96N.
(9) Please handle the LCD module by holding it on the side or back metal frame.
(10) Top sheets shall be cleaned gently using a soft cloth such as those used for glasses.
Hard w iping accumulated dust w ill leave scars on the surface even using a cloth.
(1) Using the LCM module beyond the specified maximum ratings may result in its permanent
destruction. LCM module's should usually be used under recommended operating conditions
show n in chapter 5. Exceeding any of these conditions may adversely affect its reliability.
(2) The response time w ill be strongly increased at temperatures below the specified operating
temperature range. The background color w ill change to a dark blue at temperatures about the
specified operating temperature range. How ever those phenomena are reversible and w ill
disappear w hen returning to the specified operating temperature range.
(3) If the display surface is pushed hard during operation, some display patterns w ill be abnormally
displayed.
Displays, Sh.
Date Aug. 2, 2000 3284PS 2711 -SX19V007-ZZA - 5 Page 11-3/4
Hitachi, Ltd. No.
(4) Even a slight dew depositing on the terminals may cause electrochemical reaction w hich leads to
terminal open circuit. Please operate the LCD module under the relative condition of 40°C 85%RH.
(5) Resistance range : Your controller shall be set up to allow the resistance range of touch panel
specified in our CAS.
(6) Pointed position of touch panel may shift ow ing to a change in resistance of touch panel
depending on the operation condition. To compensate this shift, the set shall be given a calibration
function.
(7) Input shall be made w ith a stylus pen (polyacetal, R0.8). Chances are very high that use of a
metal piece including a ball point pen or sharp edge w ill impair accuracy.
(8) The touch panel is an auxiliary input device. The system shall be designed to have other input
device.
11.6 STORAGE
In case of storing the LCD module for a long period of time (for instance, for years) for the purpose
of replacement use, the follow ing precautions necessary.
(1) Please store the LCD modules in a dark place ; do not expose them to sunlight or ultraviolet light.
(2) Please keep the temperature betw een 10°C and 35°C at normal humidity.
(3) Please store the LCD modules in the container w hich w as used for shipping by Hitachi.
(4) No articles shall be left on the surface over an extended period of time.
11.7 SAFETY
The LCD modules include a Cold Cathode Fluorescent Lamp (CFL). The CFL contains a small
amount of mercury. Please follow local ordinances or regulations for disposal.
Wear finger cots or gloves w henever handling or assembling a touch panel because its glass
edges are sharp.
Displays, Sh.
Date Aug. 2, 2000 3284PS 2711 -SX19V007-ZZA - 5 Page 11-4/4
Hitachi, Ltd. No.
12. DESIGNATION OF LOT MARK
12.1 LOT MARK
Lot mark is consisted of 4 digits for production lot and
6 or 7 digits for production control.
Figure in
Year
0 0 5 1 lot mark
2000 0
Month 2002 2
2003 3
Year
Displays, Sh.
Date Aug. 2, 2000 3284PS 2712 -SX19V007-ZZA - 5 Page 12-1/2
Hitachi, Ltd. No.
12.2 REVISION
REV No. ITEM LOT No. PRODUCTION CONTROL No.
A Segment LCD Driver : BD66134S 00001∼
B Segment LCD Driver : BD66134U 00001∼
C Segment LCD Driver : WFP-7102 00001∼
Label A
Label B
WARNING HIGH VOLTAGE
SX19V007-ZZA
Lot No.
Production
0051TN00001
Control No. REV. MADE IN
52 00 0H 6 K 1 1 200001
Displays, Sh.
Date Aug. 2, 2000 3284PS 2712 -SX19V007-ZZA - 5 Page 12-2/2
Hitachi, Ltd. No.
13. PRECAUTION FOR USE
(1) A limit sample should be provided by the both parities on an occasion w hen the both parties
agree to its necessity.
Judgment by a limit sample shall take effect after the limit sample has been established and
confirmed by the both parties.
(2) On the follow ing occasions, the handling of the problem should be decided through
discussion and agreement betw een responsible persons of the both parties.
(1) When a question is arisen in the specifications.
(2) When a new problem is arisen w hich is not specified in the specifications.
(3) When an inspection specification change or operating condition change by customer
is reported to HITACHI, and some problem is arisen in the specification due to the
change.
(4) When a new problem is arisen at the customer's operating set for sample evaluation
(3) Regarding the treatment for maintenance and repairing, both parties w ill discuss it in six month
later after latest delivery of this product.
The precaution that should be observed w hen handling LCM have been explained above.
If any points are unclear or if you have any requests, please contact Hitachi.
Displays, Sh.
Date Aug. 2, 2000 3284PS 2713 -SX19V007-ZZA - 5 Page 13-1/1
Hitachi, Ltd. No.