LMC2015-V4-DIGIT-M MANUAL

LMC2015_DIGIT_M_V4(0)

LMC2015 DIGIT-M CARD

USER MANUAL

CONTENT

Instructions for security...............................................................................................................1

一.OVERVIEW............................................................................................................................2
1.1 How to identify LMCV4-DIGIT-M control card.......................................................2
1.2 Main Feature.....................................................................................................................3
二、Electrical connections...........................................................................................................3
2.1Interface Description.....................................................................................................3
2.1.1 Power supply...................................................................................................................................3
2.1.2 CON1 ：DB15 Scanhead control...................................................................................................4
2.1.3 CON2 ：DB25 Laser control......................................................................................................5
2.1.4 CON4：DB15 Power/Extension/IO socket..............................................................................7
2.2 Digital input output signal connection................................................................8
2.2.1 INPUT SIGNAL XORG0,GIN15, Remark .........................................................................................8
2.2.2 Output signal OUT4，OUT5...........................................................................................................9
2.3 Card size---------------------------------------------------------------------------------------------9
 LMC2015-V4-DIGIT-M MANUAL

Instructions for security

Before installing and using the LMCV4-Digit-M control card, read this section
carefully. If you have any questions about this document, please contact BJJCZ.

1. Safety operation steps

 Please abide by all the safety descriptions of laser (including but
not limited to the relevant chapters described in laser, vibration
mirror, and in this document)
 At any time,please turn on the laser power supply after turning on the
computer power supply,LMCDIGIT-M power supply and mirror power supply.
Otherwise, it may cause damage due to an uncontrollable laser beam.
We recommend that you use light sluration to avoid damage caused by
uncontrollable laser

2. The safety part of the customer is responsible

 LMCV4-Digit-M is designed to control a laser scanning system. Therefore,

all safety instructions for laser systems should be understood and
implemented by customers. Customers must strictly abide by the relevant
safety operation instructions and independently responsible for the
safety of the laser system used.
 Security rules may be different due to different countries. Customers
have the responsibility to abide by all local regulations.
 Please check carefully before running the software. Software errors
may cause the system to stop response. In this case, both vibration
mirrors and laser are not controlled.
 Please avoid damage to the impact of wet, dust, corrosion and foreign
objects.
 When storing and using board cards, avoid damage to the electromagnetic
field and static electricity. They may damage the electronic devices
on the board. Please use the anti -static packaging bag to store the
card;
 Please ensure that the board is stored in the environment from -20 ° C to+60 °
C. The allowable working environment temperature is 25 ℃ ± 10 ℃.

1
 LMC2015-V4-DIGIT-M MANUAL

一、Overview

1.1 How to identify LMC-Digit-M control card

"Model: LMCV4-DIGIT-M" "Rev: 20151013" is printed on the upper left left position,
as shown in Figure 1-1.

Figure 1-1 LMC2015 digit-M Display diagram of control card

CON1：SCANHEAD Control interface， DB15 socket

2
 LMC2015-V4-DIGIT-M MANUAL

CON2：CO2/YAG Series Laser's DB25 control interface；

CON4：IO interface，Used to connect the power supply and extend the axis control
signal, the DB15 socket

1.2 Main Feature

 The vibration mirror control signal is a digital signal, which can directly
connect the international universal digital vibration mirror
 Extended shaft (step motor/servo motor) output: the direction/pulse signal
control step motor (or servo motor) of a channel can be used for output a shaft
or splicing
 2 GM input digital signals (compatible with TTL). Xorg0, (in15)
 2 General output digital signals (TTL compatibility). OUT4, out5 is TTL output
 Remark (cache content repeated label) signal: The same content for marking
content, requiring high -speed marks. (If the marking content contains variable
texts, or more marked content cannot be stored in the board card, it must be
connected to the general input signal.)
 Compatible with USB2.0

二、Electrical Connections

2.1 Interface Description

2.1.1 Power Supply

 The control card requires a 5V DC power supply. It is recommended to use

a 5V/3A DC power supply. 4/5/12/13 pipe foot access from the CON4 plague

CON4 NAME DESCRIPTION

4， 5 VCC +5V,Positive polarity of the
power supply
11，12，13 GND Ground. The negative polar
end of the power supply.

3
 LMC2015-V4-DIGIT-M MANUAL

2.1.2 CON1 ：DB15 SCANHEAD CONTROL

The vibration mirror control signal is a digital signal, which can be directly
connected to the digital vibration mirror. Different digital signals used in digital
vibration mirrors
The transmission protocol is not exactly the same, so it is necessary to confirm
what the transmission protocol is used in the digital mirror. Our company also
provides a digital transfer simulation rotary board, which can also be converted
into an analog signal output to connect to the analog vibration mirror through this
conversion board.

Figure 2-1 CON1 Site tube foot definition schematic diagram

4
 LMC2015-V4-DIGIT-M MANUAL

CON1 NAME DESCRIPTION

1，9 CLK－ / CLK＋ Clock signal－ / Clock signal＋
2，10 SYNC－ / SYNC＋ Synchronous signal－ /
Synchronous signal＋
3，11 X Channel－ / X Channel＋ Scanhead X signal－ /
Scanhead X signal＋
4，12 Y Channel－ / Y Channel＋ Scanhead Y signal－ /
Scanhead Y signal＋
5，13 NULL reserve
6，14， NULL reserve
7 NULL reserve
8，15 GND Ground

Digital signals are recommended to connect with twisted wires with shielding
layers.

2.1.3 CON2 ：DB25 LASER CONTROL

5
 LMC2015-V4-DIGIT-M MANUAL

F i g u r e 2-2 CON2 Site tube foot definition schematic diagram

CON2 SIGNAL NAME DESCRIPTION

3, ,5， Reference place for control cards. It is also the
6，8, 10, reference of the control card 5V input power. This
11，14，17， GND signal is a reference for all other signals on the
18，19 CON2 socket on the digital interface board.

20 QKILL The first pulse suppress signal. TTL output. The

reference signal is GND.
Frequency control signal/first pulse suppression
9 DAPORT2 signal. This signal is an analog signal [0V -5V],
with a maximum driving current of 5mA. This signal
can be set in the software. Moderate with GND
signals.
Laser power control signal. This signal is an analog
21 DAPORT1
signal [0V -10V], with a maximum driving current of
5mA. Moderate with GND signals.
23 RedPt / OUT8 Red light indicator signal / universal output
signal 8. TTL output. Reference signal GND

Laser switch signal (light gate signal). TTL

12 LaserO-
output. Moderate with GND signals. Low level is
effective.
Laser switch signal (light gate signal). TTL
24 LaserO+
output. Moderate with GND signals. High level
effective
25， 13 PWM-/PWM+ PWM signal. Differential output.
PWM signal. TTL output. The reference signal is
GND. For CO2 laser, this signal is used to set the
22 PWMTTL
power of the laser, and it is also used as a Tickle
signal output; for YAG laser, this signal is used
as a repeat frequency signal for Q drive.

Note: CON2 is the mother socket interface

6
 LMC2015-V4-DIGIT-M MANUAL

2.1.4 CON4：DB15 Power/Extension/IO socket

Figure 2-4 CON4 Site tube foot definition schematic diagram

CON4 SIGNAL NAME DESCRIPTION

Extend the axis x original point signal. Moderate with
1 XORG0 the land (12, 13 pin) of the control card. When using
this signal, connect this signal from the ground to
both ends of the switch. This signal is the input
signal.
GE input port Gin15 signal. Moderate with the land of
9 GIN15
the control card (11, 12, 13). When using this signal,
connect this signal from the ground to both ends of the
switch. This signal is the input signal.

7
 LMC2015-V4-DIGIT-M MANUAL

Universal output signal OUT4, out5. Taking the GND

2，10 OUT4，OUT5
signal as a reference place.
4，5 Vin 5V input Positive Pharmaceutical end. This signal is the
input signal.
11， The negative polar end (ground signal) of 5V input
GND
12，13 power, that is, the local signal of the control card.
This signal is the input signal.

Extend the direction signal of the axis X. This signal

14 XDIR+
is TTL output signal. Gongyang output, use VCC and XDIR+
signals, VCC is anode signal.
The pulse signal of the extended axis X, this signal is
15 XPUL+
TTL output signal. Gongyang output, use VCC and XPul+
signals, VCC is anode signal.
Repeat the signal. Formed a loop with the GND signal,
8 ReMark connect this signal from the ground to both ends of
the switch, respectively. When using this signal, the
control card will be marked with the content of the
cache at the time of the last label. This signal is
the input signal.

2.2 Digital input output signal connection

2.2.1INPUT SIGNAL,XORG0,GIN15,Remark.

The interface circuit schematic diagram of the input signal (Xorg0/ Gin15/
Reamrk), and the recommended connection scheme is shown in Figure 2-7, 2-8:

Figure 2-7 The interface circuit schematic diagram of the interface circuit (/xorg0/gin15/remark)

8
 LMC2015-V4-DIGIT-M MANUAL

F i g u r e 2-8 Universal input signal (/xorg0/gin15/remark) Recommended connection scheme

Input signals for these paths, you only need to provide a frequent opening
switch on the outside. The contact resistance of the switch is less than 100 ohm.

2.2.2 OUTPUT SIGNAL Out4—Out5

Output signal OUT4, OUT5 is TTL output.

TTL output must avoid short circuit or ground, otherwise it will damage the board
card.

2.3 Card Size

9
LMC2015-V4-DIGIT-M MANUAL

10