O-Rings: (Buna N)

O-RINGS
NITRILE O-RING OVERVIEW (Buna N)

MATERIAL: Butadiene Acrylonitrile Copolymer (Nitrile Rubber, NBR)
MATERIAL DESCRIPTION
Nitrile rubber (NBR), also known as Buna N, is one of the most commonly used sealing elastomers due to
its resistance to petroleum‐based fuels and lubricants and its relatively low price. Nitrile elastomers are
copolymers of acrylonitrile and butadiene. There are a number of common variations of nitrile compounds.
ACRYLONITRILE CONTENT
The acrylonitrile (ACN) content of the polymer chains can vary from 18% to 50%. Lower ACN content gives
better low‐temperature properties but inferior resistance to fuels and polar lubricants. Higher ACN content
gives lesser quality low‐temperature properties but improved fuels and polar lubricants resistance. Standard
NBRs typically have 34% ACN content.
CURE SYSTEM: SULFUR-CURED

Standard Nitriles are usually sulfur‐cured. Sulfur‐cured compounds offer better low‐temperature properties
but are more prone to hardening with high temperatures. Peroxide‐cured nitriles have better heat resistance
and lower compression sets but are more expensive and more difficult to process.
O-RING & * RAGCO supports the autonomy of its locations to select the best products to service their markets.
66 O-RING CORD Subtle variations of these specification may exist. Contact your RAGCO affiliate for confirmation.
NITRILE O-RING OVERVIEW (Buna N) continued
OTHER COMMON VARIATIONS
• Nitriles often are internally lubricated to improve ease of installation or reduce friction for dynamic
applications.
• Nitriles can be formulated with only “white list” ingredients, as specified in 21.CFR 177.2600, for use in
applications where the elastomer will be in contact with food or beverages.
• Nitriles can be submitted for approval by the National Sanitation Foundation (NSF) for use in drinking
water applications.
• Nitriles can also be submitted for approval to Underwriters Laboratories (UL) for use in applications as
prescribed in UL 157.
• Nitrile rubber can be combined with polyvinyl chloride (PVC) to create fuel, ozone and weathering
resistance NBR‐PVC blends.
GENERAL INFORMATION
ASTM D1418 DESIGNATION NBR STANDARD COLOR Black
ISO/DIN 1629 DESIGNATION NBR HARDNESS RANGE 40 to 90 Shore A
ASTM D2000/ SAE J 200 CODES BF, BG, BK, CH RELATIVE COST Low
SERVICE TEMPERATURES
-40°F -67°F
STANDARD LOW TEMPERATURE SPECIAL COMPOUND LOW TEMPERATURE
-40°C -55°C
212°F 275°F
STANDARD LOW TEMPERATURE SPECIAL COMPOUND HIGH TEMPERATURE
100°C 135°C
PERFORMS WELL IN DOESN'T PERFORM WELL IN

• Petroleum based oils and fuels • Aromatic hydrocarbons
• Aliphatic hydrocarbons • Automotive brake fluid
• Vegetable oils • Chlorinated hydrocarbons
• Silicone oils and greases • Ketones
• Ethylene glycol • Ethers
• Dilute acids • Esters
• Water to below 100°C (212°F) • Phosphate ester hydraulic fluids
• Strong acids
• Ozone/weathering/sunlight
* RAGCO supports the autonomy of its locations to select the best products to service their markets. O-RING &
Subtle variations of these specification may exist. Contact your RAGCO affiliate for confirmation. O-RING CORD 67
NITRILE-70 O-RING (Buna-70)
TEST REPORT FOR COMPOUND N70 DUROMETER: 70 COLOR: BLACK
ASTM* D2000, M2BG714, A14, B14, EA14, EF11, EF21, EO14, EO34, Z1
SECTION OF
PROPERTIES REQUIREMENTS RESULTS ASTM TEST METHOD
SPEC.
ORIGINAL PHYSICAL PROPERTIES
Hardness, Shore A 70 ± 5 70.5 D2240-05
Tensile Strength 2031 PSI (min) 2206 PSI (15.2 MPa) D412-06a
Elongation 250% (min) 326% D412-06a
Modulus at 100% 530 PSI (3.66 MPa) D412-06a
Specific Gravity 1.23 g/cm3
HEAT AGE: 70 hours at 100°C (212°F)
Hardness Change ± 15 points +4 points
A14 Tensile Strength Change -20% (max) 9% D573-04
Elongation Change -40% (max) -13%
Weight Change ± 15% -1%
B14 COMPRESSION SET: 22 hours at 100°C (212°F) 25% (button) (max) 7% D395-03, Method B
WATER RESISTANCE: 70 hours at 100°C (212°F)
EA14 Tensile Strength Change +1% D471-06
Elongation Change -11%
Volume Change ± 15% +0.1%
FUEL A RESISTANCE: 70 hours at 23°C (73.4°F)
Hardness Change ± 10 points -1 points
EF11 Tensile Strength Change -25% (max) -3% D471-06
Volume Change -5% to +10% +0.3%
FUEL B RESISTANCE: 70 hours at 23°C (73.4°F)
Hardness Change 0 to -30 points -12 points
EF21 Tensile Strength Change -60 (max) -31% D471-06
Elongation Change -60 (max) -29%
Volume Change 0% to +40% +18.9%
IRM 901 OIL: 70 hours at 100°C (212°F)
Hardness Change -5 to +10 points +7 points
EO14 Tensile Strength Change -25% (max) 5% D471-06
EO34 Tensile Strength Change -45 (max) +5% D471-06
*American Society for Testing and Materials
NITRILE-90 O-RING (Buna-90)
TEST REPORT FOR COMPOUND N90 DUROMETER: 90 COLOR: BLACK
ASTM* D2000, M7BG910, B14, EO14, EO34, EF11, EF21, EA14, Z1
SECTION OF
SPEC.
Hardness, Shore A 90 ± 5 87 D2240-05
B14 COMPRESSION SET: 22 hours at 100°C (212°F) 25% (button) (max) 7.8% D395-04, Method B
EA14 Tensile Strength Change +5% D471-06
FUEL A RESISTANCE: 70 hours at 23°C (73.4°F)
EF11 Tensile Strength Change -25% (max) 0% D471-06
FUEL B RESISTANCE: 70 hours at 23°C (73.4°F)
Hardness Change 0 to -30 points -14 points
EF21 Tensile Strength Change -60 (max) -28% D471-06
EO14 Tensile Strength Change -25% (max) -2% D471-06
Volume Change -10% to +5% -2.8%
Hardness Change -10 to +5 points -5 points
EO34 Tensile Strength Change -45 (max) -3% D471-06
Volume Change 0% to +25% +6%
VITON® O-RING OVERVIEW
MATERIAL: Fluorocarbon Rubber
Fluorocarbon is a well‐known high‐performance rubber that has excellent resistance to high
temperature, ozone, weather, oxygen, mineral oil, fuels, hydraulic fluids, aromatics and many organic
solvents and chemicals.
FLUORINE CONTENT
Viton® variations include: general type (A: 66% fluorine), middle fluorine content type (B, GBL: 67 to 68.5%
fluorine), high fluorine content type (F, GF: 70% fluorine), improving low temperature flexibility type (GLT,
GFLT) and excellent resistance to more chemicals and solvents (Viton® ETP Extreme). We also can supply
excellent acid and alkali resistance parts made by VITON® TBR.
CURE SYSTEM: BISPHENOL-CURED

Standard FKM compounds are Bisphenol‐cured. FKM compounds with peroxide‐ cured possess better acid
solution resistance than the bisphenol‐cured and can replace litharge‐cured applied in acid solutions. In
some lubricants, adding a few organic amide or amine, or choosing peroxide‐cured system Viton® will be
better than bisphenol curing systems.

• FKM can also be submitted for approval to Underwriters Laboratories (UL) for use in applications as
prescribed in UL157.
• FKM has excellent resistance to high temperature, oil, solvent, flame, chemical and weather, and is
usually applied in automotive, chemical processing, aerospace and many other industries.
• Viton® GLT is broadly used in thermal range of ‐40°C to 250°C (‐40°F to 482°F) and has outstanding
resistance to aggressive HTS‐type oils which are commonly used in aerospace industries.
• Viton® ETP is usually applied in chemical industries.
• In some fuels, adding several methanols, Viton® F and B‐type are more usable
• than A‐type, especially F‐type. If it requires lower temperature, GFLT and GBLT
• will be available.
• Viton® TBR 605C (TFE/propylene polymer) is better base and steam resistant
• than other general Viton®. It can be used in amine, amide and some bases.
GENERAL INFORMATION
ASTM D1418 DESIGNATION FKM STANDARD COLOR Black
ISO/DIN 1629 DESIGNATION FKM HARDNESS RANGE 50 to 90 Shore A
ASTM D2000/ SAE J 200 CODES HK RELATIVE COST High
-15°F -40°F
-26°C -40°C
232°F 525°F
450°C 275°C

• Petroleum products • Ketones
• Fuel or blend with methanol or ethanol • Low molecular weight organic acids (formic and
• Diesel or blend with biodiesel acetic acids)
• Mineral oil and grease • Superheat steam
• Silicone oil and grease • Low molecular weight esters and ethers
• High vacuum • Phosphate ester based hydraulic fluids‐Skydrol®
• Ozone, weather and very high temperature air
• Strong acid
VITON®-75 O-RING
TEST REPORT FOR COMPOUND V75 DUROMETER: 75 COLOR: BLACK
ASTM* D2000, M2HK810, A1-10, B38, EF31, EO78, Z1, Z2
SECTION OF
SPEC.
Z1 Tensile Strength 1450 PSI (min) 2273 PSI (15.6 MPa) D412-06a
A1-10 Tensile Strength Change -25% (max) -1% D573-04
Weight Change -1.7%
B38 COMPRESSION SET: 22 hours at 200°C (392°F) 50% (plied) (max) 11% D395-03, Method B
FUEL C RESISTANCE: 70 hours at 23°C (73.4°F)
NO. 101 OIL: 70 hours at 200°C (392°F)
VITON®-90 O-RING
TEST REPORT FOR COMPOUND V90 DUROMETER: 75 COLOR: BLACK
ASTM* D2000, M2HK810, A1-10, B38, EF31, EO78, Z1, Z2
SECTION OF
SPEC.
A1-10 Tensile Strength Change -25% (max) -11% D573-04
Weight Change -1.7%
B38 COMPRESSION SET: 22 hours at 200°C (392°F) 50% (plied) (max) 20.4% D395-03, Method B
FUEL C RESISTANCE: 70 hours at 23°C (73.4°F)
NO. 101 OIL: 70 hours at 200°C (392°F)
7700/SAE OIL: 70 hours at 200°C (392°F)
Volume Change +25% +15.3%
NEOPRENE-70 O-RING
MATERIAL: Neoprene (Chloroprene Rubber)
Chloroprene (CR), also known by its trade name “Neoprene”, was one of the first successful synthetic
elastomers in 1931 made by Dupont. It is prepared by emulsion polymerization of chloroprene, or 2‐
chlorobutadiene. CR is a multi‐purposed elastomer which yields a balanced combination of properties. It
performs well in contact with oils and many chemicals and has good resistance to sun, ozone and weather.
It also displays outstanding toughness and good resistance to fire.
CURE SYSTEM: SULFUR-CURED

Standard FKM compounds are Bisphenol‐cured. FKM compounds with peroxide‐ cured possess better acid
solution resistance than the bisphenol‐cured and can replace litharge‐cured applied in acid solutions. In
some lubricants, adding a few organic amide or amine, or choosing peroxide‐cured system Viton® will be
better than bisphenol curing systems.

• CR has been used in thousands of diverse environments, including the automotive, wire and cable industries.
• CR is most often used in air condition systems, especially old refrigerated media like R12 or R22 and
lubricants with mineral oils.
GENERAL INFORMATION
ASTM D1418 DESIGNATION CR STANDARD COLOR Black
ISO/DIN 1629 DESIGNATION CR HARDNESS RANGE 30 to 90 Shore A
ASTM D2000/ SAE J 200 CODES BC, BE RELATIVE COST Low
-40°F -67°F
-40°C -55°C
212°F 257°F
100°C 125°C
• Refrigerants • Aromatic hydrocarbons
• Ammonia • Ketones
• Water • Esters
• Silicone grease and oils • Ethers
• High aniline point mineral oil • Strong oxidizing acids
• Chlorinated hydrocarbons
TEST REPORT FOR COMPOUND C70 DUROMETER: 70 COLOR: BLACK

ASTM* D2000, M2BC710, A14, C12, F17, Z1, Z2
SECTION OF
SPEC.
Hardness Change ± 15 points (max) +9 points
A14 Tensile Strength Change -15% (max) -1% D573-04
Weight Change -2.8%
Z1 COMPRESSION SET: 70 hours at 100°C (212°F) 35% (button) (max) 33.2% D395-03, Method B
OZONE RESISTANCE:
C12 No crack Pass D1171-99
50 pphm, 70 hours at 40°C (104°F)
LOW‐TEMPERATURE BRITTLENESS POINT:
3 minutes at‐40°C (‐40°F)
F17 Sample type: T‐50 D2137-94, Method A
Coolant : Methanol
Brittleness temperature to nearest 1°C (1°F) No crack Pass
EPDM-70 O-RING
MATERIAL: Ethylene Propylene (EPR, EPDM)
Ethylene Propylene Rubber (EPDM) is a Copolymer of ethylene and propylene. Furthermore, it is a
terpolymer of ethylene and propylene with a small amount of a third monomer (usually a diolefin) to
permit vulcanization with sulfur. Generally, EPDM possesses an excellent resistance to ozone, sunlight and
weathering, and has very good flexibility at low temperature, good chemical resistance (many dilute acids
and alkalis as well as polar solvents) and good electrical insulation property.
CURE SYSTEM: PEROXIDE-CURED

Standard EPDMs are usually sulfur‐cured. Sulfur‐cured compounds offer better flexible properties but are
more prone to hardening and have an inferior compression set with high temperature. Peroxide‐cured
EPDMs have better heat resistance and a lower compression set. It complies with long‐ time usage,
especially for hose systems in the construction industry, but is more expensive and more difficult for
production than the sulfur‐cured EPDMs.

• EPDMs often are internally lubricated to improve ease of installation or reduce friction for dynamic
applications.
• EPDMs can be formulated with only “white list” ingredients, as specified in 21.CFR 177.2600, for use in
• EPDMs can be submitted for approval by the National Sanitation Foundation (NSF) for use in drinking
water applications.
• EPDMs are usually used in automotive air conditioning systems where there is use of R134a refrigerant
gas and POE or PAG lubricant and new refrigerant for environment protection R744. R744 air conditioning
systems require excellent resistance to explosive decompression in hydrogen dioxide at high pressure
and high temperature.
• EPDMs are usually used in phosphate ester type hydraulic fluids.
GENERAL INFORMATION
ASTM D1418 DESIGNATION EPM, EPDM STANDARD COLOR Black
ISO/DIN 1629 DESIGNATION EPM, EPDM HARDNESS RANGE 30 to 90 Shore A
ASTM D2000/ SAE J 200 CODES AA, BA, CA, DA RELATIVE COST Low
-67°F -67°F
-55°C -55°C
257°F 302°F
125°C 150°C
• Alcohols • Aliphatic and aromatic hydrocarbons
• Automotive brake fluid • Di‐ester based lubricants
• Ketones • Halogenated solvents
• Dilute acids and alkalis • Petroleum based oils and greases
• Silicone oils and greases
• Steam up to 204.4°C (400°F)
• Water
• Phosphate ester based hydraulic fluids‐Skydrol®
• Ozone, aging and weathering
TEST REPORT FOR COMPOUND E70 DUROMETER: 70 COLOR: BLACK

ASTM* D2000, M4CA714, A25, B44, EA14, F17, Z1, Z2
SECTION OF
SPEC.
Weight Change -2.9%
Hardness Change -3 points
EA14 Tensile Strength Change -13% D471-06
Elongation Change +2%
3 minutes at ‐40°C (‐40°F)
D2137-05,
Sample type: T‐50
Method A
F17 Coolant : Methanol
SILICONE-70 O-RING
MATERIAL: Silicone Rubber (MQ, VMQ, PVMQ)
Physically, silicones are based on silicon, an element derived from quartz. To create this class of synthetic
elastomers, pendant organic groups such as methyl, phenyl and vinyl are attached to silicon atoms.
Different additions of side chains can achieve significant variations in properties. Silicones have excellent
heat, ozone and corona resistance and have good dielectric stability and resistance to many oils, chemicals
and solvents. Silicones possess the best flexible property at low temperature but have low tensile strength
and poor wear and tear resistance.
CURE SYSTEM: PEROXIDE-CURED

Standard silicone compounds are usually peroxide‐cured. Platinum‐ cured compounds offer better flexible
properties and very low volatile matter. Platinum‐cured silicones usually are applied in medical systems or
other required low volatile matter. However, they need to be produced in a clean room and with a higher
cost of platinum catalyzer, making them more expensive than peroxide‐cured ones.

• Silicones can be formulated with only “white list” ingredients, as specified in 21.CFR 177.2600, for use in
• Silicones can be submitted for approval by the National Sanitation Foundation (NSF) for use in drinking
water applications.
• Silicones are most often used in automotive systems in boots, oil filter valves, gasket in light, etc.
• Silicone parts can be used in medical systems which especially require compliance to USP CLASS VI
GENERAL INFORMATION
Q, MQ, VMQ,
ASTM D1418 DESIGNATION STANDARD COLOR Rust
PVMQ
Q, MQ, VMQ,
ISO/DIN 1629 DESIGNATION HARDNESS RANGE 25 to 90 Shore A
PVMQ
ASTM D2000/ SAE J 200 CODES FC, FE, GE RELATIVE COST Medium to High
-76°F -150°F
-60°C -100°C
437°F 572°F
225°C 300°C
• Petroleum products • Ketones
• Fuel or blend with methanol or ethanol • Low molecular weight organic acids (formic and
• Diesel or blend with biodiesel acetic acids)
• Mineral oil and grease • Superheat steam
• Silicone oil and grease • Low molecular weight esters and ethers
• High vacuum • Phosphate ester based hydraulic fluids‐Skydrol®
• Ozone, weather and very high temperature air
• Strong acid
SILICONE-70 O-RING continued
TEST REPORT FOR COMPOUND S70 DUROMETER: 70 COLOR: RUST
ASTM* D2000, M5GE706, A19, B37, EO16, EO36, EA14, F19, Z1
SECTION OF
SPEC.
Hardness, Shore A 70 ± 5 69.5 D2240-05
A19 Tensile Strength Change -25% (max) +4% D573-04
Weight Change -4%
Hardness Change 0 to -15 -4 points
EO16 Tensile Strength Change -20 (max) +11% D471-06
Elongation Change -20 (max) 0%
Volume Change 0% to +10% +4%
Hardness Change -30 points (max) -19 points
Volume Change +60% (max) +33.7%
Hardness Change ± 5% 0 points
3 minutes at ‐55°C (‐40°F)
D2137-05,
Sample type: T‐50
Method A
F17 Coolant : Methanol
TEFLON® O-RING
MATERIAL: Polytetrafluoroethylene (PTFE)
Polytetrafluoroethylene (PTFE) is a high molecular weight polymer, one of the most versatile plastic
materials known and useful for a large range of products for applications excluded to other materials.
PTFE is generally considered a thermoplastic polymer; at 327°C (620.6°F) it retains a very high viscosity, thus
requiring particular transformation techniques for manufacturing of finished and semi‐finished goods. PTFE
can be used in a temperature range from ‐200°C (‐328°F) to +260°C (500°F).
OUTSTANDING CHARACTERISTICS
• High heat resistance
• High resistance to chemical agents and solvents • High anti‐adhesiveness
• High dielectric properties
• Low friction coefficient
• Non‐toxicity
THERMAL PROPERTIES
PTFE is one of the most thermally stable plastic materials. There is no appreciable decomposition at 260°C
(500°F), so that PTFE, at this temperature, still possesses the greater part of its properties. Appreciable
decomposition begins at over 400°C (932°F). The coefficient of the thermal conductivity of PTFE does not
vary with the temperature. It is relatively high, so that PTFE can be considered to be a good insulating
material. The mixing of suitable fillers improves the thermal conductivity.
BEHAVIOR IN PRESENCE OF FOREIGN AGENTS

PTFE is practically inert against known elements and compounds. It is attacked only by the alkaline metals in
the elementary state, by Chlorine trifluoride and by elementary Fluorine at high temperatures and pressures.
PTFE is insoluble in almost all solvents at temperatures up to about 300°C (572°F). Fluorinated hydrocarbons
cause a certain swelling which is however reversible; some highly fluorinated oils, at temperatures over
300°C (572°F), exercise a certain dissolving effect upon PTFE. High energy radiation tends to cause the
breaking of the PTFE molecule, so that the resistance of the product to radiation is rather poor. The gas
permeability of PTFE is similar to other plastic materials. The permeability does not depend only on the
thickness and pressure, but also on the working techniques.
PHYSICAL‐MECHANICAL PROPERTIES
The tensile and compressive properties are to a large degree influenced by the working processes and
the polymer used. PTFE, however, can be used continuously at temperatures up to 260°C (500°F), while
possessing still a certain compressive plasticity at temperatures near to the absolute Zero.
The hardness Shore D, measured according to the method ASTM D 2240, has values comprised between
D50 and D60. According DIN 53456 (load 13.5 Kg for 30 sec.) results in an hardness range between
27 and 32 N/mm2.
TEFLON® O-RING continued
TEST REPORT FOR COMPOUND TEF DUROMETER: 50 - 60 SHORE D COLOR: WHITE
PROPERTIES RESULTS ASTM* TEST METHOD
Density 2.14 - 2.18 g/cm3 D792

Tensile Strength > 20 N/mm2 D4894
Elongation at Break > 200% D4894
Compressive Strength at 1% Deformation 4 -5 N/mm 2
D695
Coefficient of Friction (dynamic) 0.06 D1894
Service Temperature (min‐max) -200°C (-328°F) min
+260°C (500°F) max
Dielectric Strength in Air 1.33 g/cm3 D149
POLYURETHANE O-RING OVERVIEW
MATERIAL: Polyurethane Rubber (PU, AU, EU)
The millable Polyurethane (PU) rubbers are distinguished into two types; the first is polyester urethane
(AU) and the other is polyether urethane (EU). AU type urethanes have outstanding oil, fuel and solvent
resistance but can be attacked by hydrolysis. EU type urethanes are not attacked by hydrolysis and still offer
a fuel and oil resistance comparable to low ACN (18 to 22% ACN) Nitriles or HNBRs. Any type polyurethane
has excellent wear resistance, high tensile strength and high elasticity in comparison with any other
elastomers. We can also offer any type thermoplastic urethane (TPU).
CURE SYSTEM: PEROXIDE-CURED Standard PU compounds are peroxide‐cured.

• Polyurethane usually is applied in the mechanical industry, especially in places where material must have
higher wear resistance and strength.
• In some applying environments, moisture condensing will happen on the surface of the rubber seal; this
will cause hydrolysis of AU so choosing EU is better in these cases. However, EU does not resist oil very
well, thus higher aniline point oil must be used for lubricant application.
• TPU will be better than millable polyurethane when applied in hydraulic systems.
GENERAL INFORMATION
ASTM D1418 DESIGNATION AU, EU STANDARD COLOR Transparent
ISO/DIN 1629 DESIGNATION AU, EU HARDNESS RANGE 60 to 93 Shore A
ASTM D2000/ SAE J 200 CODES BG RELATIVE COST Medium to High
-40°F -67°F
-40°C -55°C
176°F 212°F
80°C 100°C

• Aliphatic hydrocarbon • Ketones
• Mineral oil and grease • Alcohols
• Silicone oil and grease • Esters
• Ozone • Ethers
• Water up to 50°C (122°F) EU type • Hot water and steam
• Alkalis, amines
• Acids
• Glycols
POLYURETHANE-70 O-RING
TEST REPORT FOR COMPOUND U70 DUROMETER: 70 COLOR: TRANSPARENT
ASTM* D2000, M3BG714, B14, EA14, EO14, Z1, Z2
SECTION OF
SPEC.
Volume Change ± 15% +5%
NO. 1 OIL RESISTANCE:
70 hours at 100°C (212°F)
EO14 D471-06
Tensile Strength Change -20% (max) -6%
70 hours at 100°C (212°F)
Hardness Change -30 points
Z2 D471-06
Tensile Strength Change -46%
Volume Change +56.1%
POLYURETHANE-90 O-RING
TEST REPORT FOR COMPOUND U90 DUROMETER: 90 COLOR: TRANSPARENT
ASTM* D2000, M3BG910, A14, B14, EA14, EO14, Z1, Z2, Z3
SECTION OF
SPEC.
Hardness Change ± 15 points 0 points
Weight Change +0.1%
70 hours at 100°C (212°F)
EO14 D471-98
Tensile Strength Change -20% (max) -17%
TENSILE SET: Hold 100% Elongation for 2

Z3 10.2%
minutes, Release tension and rest 2 minutes
STANDARD O-RING SIZES
AS568 SIZE CHART (continued)
Actual Dimensions
AS568 Nominal Reference
Inches Metric
Dash # CS (IN) ID (IN) OD (IN) CS ID ID Tol CS ID ID Tol
001 1/32 1/32 3/32 0.040 0.029 ± 0.004 1.02 0.74 ± 0.10
002 3/64 3/64 9/64 0.050 0.042 ± 0.004 1.27 1.07 ± 0.10
003 1/16 1/16 3/16 0.060 0.056 ± 0.004 1.52 1.42 ± 0.10
004 1/16 5/64 13/64 0.070 0.070 ± 0.005 1.78 1.78 ± 0.13
005 1/16 3/32 7/32 0.070 0.101 ± 0.005 1.78 2.57 ± 0.13
006 1/16 1/8 1/4 0.070 0.114 ± 0.005 1.78 2.90 ± 0.13
007 1/16 5/32 9/32 0.070 0.145 ± 0.005 1.78 3.68 ± 0.13
008 1/16 3/16 5/16 0.070 0.176 ± 0.005 1.78 4.47 ± 0.13
009 1/16 7/32 11/32 0.070 0.208 ± 0.005 1.78 5.28 ± 0.13
010 1/16 1/4 3/8 0.070 0.239 ± 0.005 1.78 6.07 ± 0.13
011 1/16 5/16 7/16 0.070 0.301 ± 0.005 1.78 7.65 ± 0.13
012 1/16 3/8 1/2 0.070 0.364 ± 0.005 1.78 9.25 ± 0.13
013 1/16 7/16 9/16 0.070 0.426 ± 0.005 1.78 10.82 ± 0.13
014 1/16 1/2 5/8 0.070 0.489 ± 0.005 1.78 12.42 ± 0.13
015 1/16 9/16 11/16 0.070 0.551 ± 0.007 1.78 14.00 ± 0.18
016 1/16 5/8 3/4 0.070 0.614 ± 0.009 1.78 15.60 ± 0.23
017 1/16 11/16 13/16 0.070 0.676 ± 0.009 1.78 17.17 ± 0.23
018 1/16 3/4 7/8 0.070 0.739 ± 0.009 1.78 18.77 ± 0.23
019 1/16 13/16 15/16 0.070 0.801 ± 0.009 1.78 20.35 ± 0.23
020 1/16 7/8 1 0.070 0.864 ± 0.009 1.78 21.95 ± 0.23
021 1/16 15/16 1-1/16 0.070 0.926 ± 0.009 1.78 23.52 ± 0.23
022 1/16 1 1-1/8 0.070 0.989 ± 0.010 1.78 25.12 ± 0.25
023 1/16 1-1/16 1-3/16 0.070 1.051 ± 0.010 1.78 26.70 ± 0.25
024 1/16 1-1/8 1-1/4 0.070 1.114 ± 0.010 1.78 28.30 ± 0.25
025 1/16 1-3/16 1-5/16 0.070 1.176 ± 0.011 1.78 29.87 ± 0.28
026 1/16 1-1/4 1-3/8 0.070 1.239 ± 0.011 1.78 31.47 ± 0.28
027 1/16 1-5/16 1-7/16 0.070 1.301 ± 0.011 1.78 33.05 ± 0.28
028 1/16 1-3/8 1-1/2 0.070 1.364 ± 0.013 1.78 34.65 ± 0.33
029 1/16 1-1/2 1-5/8 0.070 1.489 ± 0.013 1.78 37.82 ± 0.33
030 1/16 1-5/8 1-3/4 0.070 1.614 ± 0.013 1.78 41.00 ± 0.33
031 1/16 1-3/4 1-7/8 0.070 1.739 ± 0.015 1.78 44.17 ± 0.38
032 1/16 1-7/8 2 0.070 1.864 ± 0.015 1.78 47.35 ± 0.38
033 1/16 2 2-1/8 0.070 1.989 ± 0.018 1.78 50.52 ± 0.46
034 1/16 2-1/8 2-1/4 0.070 2.114 ± 0.018 1.78 53.70 ± 0.46
035 1/16 2-1/4 2-3/8 0.070 2.239 ± 0.018 1.78 56.87 ± 0.46
036 1/16 2-3/8 2-1/2 0.070 2.364 ± 0.018 1.78 60.05 ± 0.46
037 1/16 2-1/2 2-5/8 0.070 2.489 ± 0.018 1.78 63.22 ± 0.46
038 1/16 2-5/8 2-3/4 0.070 2.614 ± 0.020 1.78 66.40 ± 0.51
039 1/16 2-3/4 2-7/8 0.070 2.739 ± 0.020 1.78 69.57 ± 0.51
040 1/16 2-7/8 3 0.070 2.864 ± 0.020 1.78 72.75 ± 0.51
041 1/16 3 3-1/8 0.070 2.989 ± 0.024 1.78 75.92 ± 0.61
Actual Dimensions
Inches Metric
042 1/16 3-1/4 3-3/8 0.070 3.239 ± 0.024 1.78 82.27 ± 0.61
043 1/16 3-1/2 3-5/8 0.070 3.489 ± 0.024 1.78 88.62 ± 0.61
044 1/16 3-3/4 3-7/8 0.070 3.739 ± 0.027 1.78 94.97 ± 0.69
045 1/16 4 4-1/8 0.070 3.989 ± 0.027 1.78 101.32 ± 0.69
046 1/16 4-1/4 4-3/8 0.070 4.239 ± 0.030 1.78 107.67 ± 0.76
047 1/16 4-1/2 4-5/8 0.070 4.489 ± 0.030 1.78 114.02 ± 0.76
048 1/16 4-3/4 4-7/8 0.070 4.739 ± 0.030 1.78 120.37 ± 0.76
049 1/16 5 5-1/8 0.070 4.989 ± 0.037 1.78 126.72 ± 0.94
050 1/16 5-1/4 5-3/8 0.070 5.239 ± 0.037 1.78 133.07 ± 0.94
102 3/32 1/16 1/4 0.103 0.049 ± 0.005 2.62 1.24 ± 0.13
103 3/32 3/32 9/32 0.103 0.081 ± 0.005 2.62 2.06 ± 0.13
104 3/32 1/8 5/16 0.103 0.112 ± 0.005 2.62 2.84 ± 0.13
105 3/32 5/32 11/32 0.103 0.143 ± 0.005 2.62 3.63 ± 0.13
106 3/32 3/16 3/8 0.103 0.174 ± 0.005 2.62 4.42 ± 0.13
107 3/32 7/32 13/32 0.103 0.206 ± 0.005 2.62 5.23 ± 0.13
108 3/32 1/4 7/16 0.103 0.237 ± 0.005 2.62 6.02 ± 0.13
109 3/32 5/16 1/2 0.103 0.299 ± 0.005 2.62 7.59 ± 0.13
110 3/32 3/8 9/16 0.103 0.362 ± 0.005 2.62 9.19 ± 0.13
111 3/32 7/16 5/8 0.103 0.424 ± 0.005 2.62 10.77 ± 0.13
112 3/32 1/2 11/16 0.103 0.487 ± 0.005 2.62 12.37 ± 0.13
113 3/32 9/16 3/4 0.103 0.549 ± 0.007 2.62 13.94 ± 0.18
114 3/32 5/8 13/16 0.103 0.612 ± 0.009 2.62 15.54 ± 0.23
115 3/32 11/16 7/8 0.103 0.674 ± 0.009 2.62 17.12 ± 0.23
116 3/32 3/4 15/16 0.103 0.737 ± 0.009 2.62 18.72 ± 0.23
117 3/32 13/16 1 0.103 0.799 ± 0.010 2.62 20.29 ± 0.25
118 3/32 7/8 1-1/16 0.103 0.862 ± 0.010 2.62 21.89 ± 0.25
119 3/32 15/16 1-1/8 0.103 0.924 ± 0.010 2.62 23.47 ± 0.25
120 3/32 1 1-3/16 0.103 0.987 ± 0.010 2.62 25.07 ± 0.25
121 3/32 1-1/16 1-1/4 0.103 1.049 ± 0.010 2.62 26.64 ± 0.25
122 3/32 1-1/8 1-5/16 0.103 1.112 ± 0.010 2.62 28.24 ± 0.25
123 3/32 1-3/16 1-3/8 0.103 1.174 ± 0.012 2.62 29.82 ± 0.30
124 3/32 1-1/4 1-7/16 0.103 1.237 ± 0.012 2.62 31.42 ± 0.30
125 3/32 1-5/16 1-1/2 0.103 1.299 ± 0.012 2.62 32.99 ± 0.30
126 3/32 1-3/8 1-9/16 0.103 1.362 ± 0.012 2.62 34.59 ± 0.30
127 3/32 1-7/16 1-5/8 0.103 1.424 ± 0.012 2.62 36.17 ± 0.30
128 3/32 1-1/2 1-11/16 0.103 1.487 ± 0.012 2.62 37.77 ± 0.30
129 3/32 1-9/16 1-3/4 0.103 1.549 ± 0.015 2.62 39.34 ± 0.38
130 3/32 1-5/8 1-13/16 0.103 1.612 ± 0.015 2.62 40.94 ± 0.38
131 3/32 1-11/16 1-7/8 0.103 1.674 ± 0.015 2.62 42.52 ± 0.38
132 3/32 1-3/4 1-15/16 0.103 1.737 ± 0.015 2.62 44.12 ± 0.38
133 3/32 1-13/16 2 0.103 1.799 ± 0.015 2.62 45.69 ± 0.38
STANDARD O-RING SIZES continued
Actual Dimensions
Inches Metric
134 3/32 1-7/8 2-1/16 0.103 1.862 ± 0.015 2.62 47.29 ± 0.38
135 3/32 1-15/16 2-1/8 0.103 1.925 ± 0.017 2.62 48.90 ± 0.43
136 3/32 2 2-3/16 0.103 1.987 ± 0.017 2.62 50.47 ± 0.43
137 3/32 2-1/16 2-1/4 0.103 2.050 ± 0.017 2.62 52.07 ± 0.43
138 3/32 2-1/8 2-5/16 0.103 2.112 ± 0.017 2.62 53.64 ± 0.43
139 3/32 2-3/16 2-3/8 0.103 2.175 ± 0.017 2.62 55.25 ± 0.43
140 3/32 2-1/4 2-7/16 0.103 2.237 ± 0.017 2.62 56.82 ± 0.43
141 3/32 2-5/16 2-1/2 0.103 2.300 ± 0.020 2.62 58.42 ± 0.51
142 3/32 2-3/8 2-9/16 0.103 2.362 ± 0.020 2.62 59.99 ± 0.51
143 3/32 2-7/16 2-5/8 0.103 2.425 ± 0.020 2.62 61.60 ± 0.51
144 3/32 2-1/2 2-11/16 0.103 2.487 ± 0.020 2.62 63.17 ± 0.51
145 3/32 2-9/16 2-3/4 0.103 2.550 ± 0.020 2.62 64.77 ± 0.51
146 3/32 2-5/8 2-13/16 0.103 2.612 ± 0.020 2.62 66.34 ± 0.51
147 3/32 2-11/16 2-7/8 0.103 2.675 ± 0.022 2.62 67.95 ± 0.56
148 3/32 2-3/4 2-15/16 0.103 2.737 ± 0.022 2.62 69.52 ± 0.56
149 3/32 2-13/16 3 0.103 2.800 ± 0.022 2.62 71.12 ± 0.56
150 3/32 2-7/8 3-1/16 0.103 2.862 ± 0.022 2.62 72.69 ± 0.56
151 3/32 3 3-3/16 0.103 2.987 ± 0.024 2.62 75.87 ± 0.61
152 3/32 3-1/4 3-7/16 0.103 3.237 ± 0.024 2.62 82.22 ± 0.61
153 3/32 3-1/2 3-11/16 0.103 3.487 ± 0.024 2.62 88.57 ± 0.61
154 3/32 3-3/4 3-15/16 0.103 3.737 ± 0.028 2.62 94.92 ± 0.71
155 3/32 4 4-3/16 0.103 3.987 ± 0.028 2.62 101.27 ± 0.71
156 3/32 4-1/4 4-7/16 0.103 4.237 ± 0.030 2.62 107.62 ± 0.76
157 3/32 4-1/2 4-11/16 0.103 4.487 ± 0.030 2.62 113.97 ± 0.76
158 3/32 4-3/4 4-15/16 0.103 4.737 ± 0.030 2.62 120.32 ± 0.76
159 3/32 5 5-3/16 0.103 4.987 ± 0.035 2.62 126.67 ± 0.89
160 3/32 5-1/4 5-7/16 0.103 5.237 ± 0.035 2.62 133.02 ± 0.89
161 3/32 5-1/2 5-11/16 0.103 5.487 ± 0.035 2.62 139.37 ± 0.89
162 3/32 5-3/4 5-15/16 0.103 5.737 ± 0.035 2.62 145.72 ± 0.89
163 3/32 6 6-3/16 0.103 5.987 ± 0.035 2.62 152.07 ± 0.89
164 3/32 6-1/4 6-7/16 0.103 6.237 ± 0.040 2.62 158.42 ± 1.02
165 3/32 6-1/2 6-11/16 0.103 6.487 ± 0.040 2.62 164.77 ± 1.02
166 3/32 6-3/4 6-15/16 0.103 6.737 ± 0.040 2.62 171.12 ± 1.02
167 3/32 7 7-3/16 0.103 6.987 ± 0.040 2.62 177.47 ± 1.02
168 3/32 7-1/4 7-7/16 0.103 7.237 ± 0.045 2.62 183.82 ± 1.14
169 3/32 7-1/2 7-11/16 0.103 7.487 ± 0.045 2.62 190.17 ± 1.14
170 3/32 7-3/4 7-15/16 0.103 7.737 ± 0.045 2.62 196.52 ± 1.14
171 3/32 8 8-3/16 0.103 7.987 ± 0.045 2.62 202.87 ± 1.14
172 3/32 8-1/4 8-7/16 0.103 8.237 ± 0.050 2.62 209.22 ± 1.27
173 3/32 8-1/2 8-11/16 0.103 8.487 ± 0.050 2.62 215.57 ± 1.27
174 3/32 8-3/4 8-15/16 0.103 8.737 ± 0.050 2.62 221.92 ± 1.27
Actual Dimensions
Inches Metric
175 3/32 9 9-3/16 0.103 8.987 ± 0.050 2.62 228.27 ± 10.27
176 3/32 9-1/4 9-7/16 0.103 9.237 ± 0.055 2.62 234.62 ± 10.40
177 3/32 9-1/2 9-11/16 0.103 9.487 ± 0.055 2.62 240.97 ± 10.40
178 3/32 9-3/4 9-15/16 0.103 9.737 ± 0.055 2.62 247.32 ± 10.40
201 1/8 3/16 7/16 0.139 0.171 ± 0.005 3.53 4.34 ± 0.13
202 1/8 1/4 1/2 0.139 0.234 ± 0.005 3.53 5.94 ± 0.13
203 1/8 5/16 9/16 0.139 0.296 ± 0.005 3.53 7.52 ± 0.13
204 1/8 3/8 5/8 0.139 0.359 ± 0.005 3.53 9.12 ± 0.13
205 1/8 7/16 11/16 0.139 0.421 ± 0.005 3.53 10.69 ± 0.13
206 1/8 1/2 3/4 0.139 0.484 ± 0.005 3.53 12.29 ± 0.13
207 1/8 9/16 13/16 0.139 0.546 ± 0.007 3.53 13.87 ± 0.18
208 1/8 5/8 7/8 0.139 0.609 ± 0.009 3.53 15.47 ± 0.23
209 1/8 11/16 15/16 0.139 0.671 ± 0.009 3.53 17.04 ± 0.23
210 1/8 3/4 1 0.139 0.734 ± 0.010 3.53 18.64 ± 0.25
211 1/8 13/16 1-1/16 0.139 0.796 ± 0.010 3.53 20.22 ± 0.25
212 1/8 7/8 1-1/8 0.139 0.859 ± 0.010 3.53 21.82 ± 0.25
213 1/8 15/16 1-3/16 0.139 0.921 ± 0.010 3.53 23.39 ± 0.25
214 1/8 1 1-1/4 0.139 0.984 ± 0.010 3.53 24.99 ± 0.25
215 1/8 1-1/16 1-5/16 0.139 1.046 ± 0.010 3.53 26.57 ± 0.25
216 1/8 1-1/8 1-3/8 0.139 1.109 ± 0.012 3.53 28.17 ± 0.30
217 1/8 1-3/16 1-7/16 0.139 1.171 ± 0.012 3.53 29.74 ± 0.30
218 1/8 1-1/4 1-1/2 0.139 1.234 ± 0.012 3.53 31.34 ± 0.30
219 1/8 1-5/16 1-9/16 0.139 1.296 ± 0.012 3.53 32.92 ± 0.30
220 1/8 1-3/8 1-5/8 0.139 1.359 ± 0.012 3.53 34.52 ± 0.30
221 1/8 1-7/16 1-11/16 0.139 1.421 ± 0.012 3.53 36.09 ± 0.30
222 1/8 1-1/2 1-3/4 0.139 1.484 ± 0.015 3.53 37.69 ± 0.38
223 1/8 1-5/8 1-7/8 0.139 1.609 ± 0.015 3.53 40.87 ± 0.38
224 1/8 1-3/4 2 0.139 1.734 ± 0.015 3.53 44.04 ± 0.38
225 1/8 1-7/8 2-1/8 0.139 1.859 ± 0.018 3.53 47.22 ± 0.46
226 1/8 2 2-1/4 0.139 1.984 ± 0.018 3.53 50.39 ± 0.46
227 1/8 2-1/8 2-3/8 0.139 2.109 ± 0.018 3.53 53.57 ± 0.46
228 1/8 2-1/4 2-1/2 0.139 2.234 ± 0.020 3.53 56.74 ± 0.51
229 1/8 2-3/8 2-5/8 0.139 2.359 ± 0.020 3.53 59.92 ± 0.51
230 1/8 2-1/2 2-3/4 0.139 2.484 ± 0.020 3.53 63.09 ± 0.51
231 1/8 2-5/8 2-7/8 0.139 2.609 ± 0.020 3.53 66.27 ± 0.51
232 1/8 2-3/4 3 0.139 2.734 ± 0.024 3.53 69.44 ± 0.61
233 1/8 2-7/8 3-1/8 0.139 2.859 ± 0.024 3.53 72.62 ± 0.61
234 1/8 3 3-1/4 0.139 2.984 ± 0.024 3.53 75.79 ± 0.61
235 1/8 3-1/8 3-3/8 0.139 3.109 ± 0.024 3.53 78.97 ± 0.61
236 1/8 3-1/4 3-1/2 0.139 3.234 ± 0.024 3.53 82.14 ± 0.61
237 1/8 3-3/8 3-5/8 0.139 3.359 ± 0.024 3.53 85.32 ± 0.61
Actual Dimensions
Inches Metric
238 1/8 3-1/2 3-3/4 0.139 3.484 ± 0.024 3.53 88.49 ± 0.61
239 1/8 3-5/8 3-7/8 0.139 3.609 ± 0.028 3.53 91.67 ± 0.71
240 1/8 3-3/4 4 0.139 3.734 ± 0.028 3.53 94.84 ± 0.71
241 1/8 3-7/8 4-1/8 0.139 3.859 ± 0.028 3.53 98.02 ± 0.71
242 1/8 4 4-1/4 0.139 3.984 ± 0.028 3.53 101.19 ± 0.71
243 1/8 4-1/8 4-3/8 0.139 4.109 ± 0.028 3.53 104.37 ± 0.71
244 1/8 4-1/4 4-1/2 0.139 4.234 ± 0.030 3.53 107.54 ± 0.76
245 1/8 4-3/8 4-5/8 0.139 4.359 ± 0.030 3.53 110.72 ± 0.76
246 1/8 4-1/2 4-3/4 0.139 4.484 ± 0.030 3.53 113.89 ± 0.76
247 1/8 4-5/8 4-7/8 0.139 4.609 ± 0.030 3.53 117.07 ± 0.76
248 1/8 4-3/4 5 0.139 4.734 ± 0.030 3.53 120.24 ± 0.76
249 1/8 4-7/8 5-1/8 0.139 4.859 ± 0.035 3.53 123.42 ± 0.89
250 1/8 5 5-1/4 0.139 4.984 ± 0.035 3.53 126.59 ± 0.89
251 1/8 5-1/8 5-3/8 0.139 5.109 ± 0.035 3.53 129.77 ± 0.89
252 1/8 5-1/4 5-1/2 0.139 5.234 ± 0.035 3.53 132.94 ± 0.89
253 1/8 5-3/8 5-5/8 0.139 5.359 ± 0.035 3.53 136.12 ± 0.89
254 1/8 5-1/2 5-3/4 0.139 5.484 ± 0.035 3.53 139.29 ± 0.89
255 1/8 5-5/8 5-7/8 0.139 5.609 ± 0.035 3.53 142.47 ± 0.89
256 1/8 5-3/4 6 0.139 5.734 ± 0.035 3.53 145.64 ± 0.89
257 1/8 5-7/8 6-1/8 0.139 5.859 ± 0.035 3.53 148.82 ± 0.89
258 1/8 6 6-1/4 0.139 5.984 ± 0.035 3.53 151.99 ± 0.89
259 1/8 6-1/4 6-1/2 0.139 6.234 ± 0.040 3.53 158.34 ± 1.02
260 1/8 6-1/2 6-3/4 0.139 6.484 ± 0.040 3.53 164.69 ± 1.02
261 1/8 6-3/4 7 0.139 6.734 ± 0.040 3.53 171.04 ± 1.02
262 1/8 7 7-1/4 0.139 6.984 ± 0.040 3.53 177.39 ± 1.02
263 1/8 7-1/4 7-1/2 0.139 7.234 ± 0.045 3.53 183.74 ± 1.14
264 1/8 7-1/2 7-3/4 0.139 7.484 ± 0.045 3.53 190.09 ± 1.14
265 1/8 7-3/4 8 0.139 7.734 ± 0.045 3.53 196.44 ± 1.14
266 1/8 8 8-1/4 0.139 7.984 ± 0.045 3.53 202.79 ± 1.14
267 1/8 8-1/4 8-1/2 0.139 8.234 ± 0.050 3.53 209.14 ± 1.27
268 1/8 8-1/2 8-3/4 0.139 8.484 ± 0.050 3.53 215.49 ± 1.27
269 1/8 8-3/4 9 0.139 8.734 ± 0.050 3.53 221.84 ± 1.27
270 1/8 9 9-1/4 0.139 8.984 ± 0.050 3.53 228.19 ± 1.27
271 1/8 9-1/4 9-1/2 0.139 9.234 ± 0.055 3.53 234.54 ± 1.40
272 1/8 9-1/2 9-3/4 0.139 9.484 ± 0.055 3.53 240.89 ± 1.40
273 1/8 9-3/4 10 0.139 9.734 ± 0.055 3.53 247.24 ± 1.40
274 1/8 10 10-1/4 0.139 9.984 ± 0.055 3.53 253.59 ± 1.40
275 1/8 10-1/2 10-3/4 0.139 10.484 ± 0.055 3.53 266.29 ± 1.40
276 1/8 11 11-1/4 0.139 10.984 ± 0.065 3.53 278.99 ± 1.65
277 1/8 11-1/2 11-3/4 0.139 11.484 ± 0.065 3.53 291.69 ± 1.65
278 1/8 12 12-1/4 0.139 11.984 ± 0.065 3.53 304.39 ± 1.65
Actual Dimensions
Inches Metric
279 1/8 13 13-1/4 0.139 12.984 ± 0.065 3.53 329.79 ± 1.65
280 1/8 14 14-1/4 0.139 13.984 ± 0.065 3.53 355.19 ± 1.65
281 1/8 15 15-1/4 0.139 14.984 ± 0.065 3.53 380.59 ± 1.65
282 1/8 16 16-1/4 0.139 15.955 ± 0.075 3.53 405.26 ± 1.91
283 1/8 17 17-1/4 0.139 16.955 ± 0.080 3.53 430.66 ± 2.03
284 1/8 18 18-1/4 0.139 17.955 ± 0.085 3.53 456.06 ± 2.16
309 3/16 7/16 13/16 0.210 0.412 ± 0.005 5.33 10.46 ± 0.13
310 3/16 1/2 7/8 0.210 0.475 ± 0.005 5.33 12.07 ± 0.13
311 3/16 9/16 15/16 0.210 0.537 ± 0.007 5.33 13.64 ± 0.18
312 3/16 5/8 1 0.210 0.600 ± 0.009 5.33 15.24 ± 0.23
313 3/16 11/16 1-1/16 0.210 0.662 ± 0.009 5.33 16.81 ± 0.23
314 3/16 3/4 1-1/8 0.210 0.725 ± 0.010 5.33 18.42 ± 0.25
315 3/16 13/16 1-3/16 0.210 0.787 ± 0.010 5.33 19.99 ± 0.25
316 3/16 7/8 1-1/4 0.210 0.850 ± 0.010 5.33 21.59 ± 0.25
317 3/16 15/16 1-5/16 0.210 0.912 ± 0.010 5.33 23.16 ± 0.25
318 3/16 1 1-3/8 0.210 0.975 ± 0.010 5.33 24.77 ± 0.25
319 3/16 1-1/16 1-7/16 0.210 1.037 ± 0.010 5.33 26.34 ± 0.25
320 3/16 1-1/8 1-1/2 0.210 1.100 ± 0.012 5.33 27.94 ± 0.30
321 3/16 1-3/16 1-9/16 0.210 1.162 ± 0.012 5.33 29.51 ± 0.30
322 3/16 1-1/4 1-5/8 0.210 1.225 ± 0.012 5.33 31.12 ± 0.30
323 3/16 1-5/16 1-11/16 0.210 1.287 ± 0.012 5.33 32.69 ± 0.30
324 3/16 1-3/8 1-3/4 0.210 1.350 ± 0.012 5.33 34.29 ± 0.30
325 3/16 1-1/2 1-7/8 0.210 1.475 ± 0.015 5.33 37.47 ± 0.38
326 3/16 1-5/8 2 0.210 1.600 ± 0.015 5.33 40.64 ± 0.38
327 3/16 1-3/4 2-1/8 0.210 1.725 ± 0.015 5.33 43.82 ± 0.38
328 3/16 1-7/8 2-1/4 0.210 1.850 ± 0.015 5.33 46.99 ± 0.38
329 3/16 2 2-3/8 0.210 1.975 ± 0.018 5.33 50.17 ± 0.46
330 3/16 2-1/8 2-1/2 0.210 2.100 ± 0.018 5.33 53.34 ± 0.46
331 3/16 2-1/4 2-5/8 0.210 2.225 ± 0.018 5.33 56.52 ± 0.46
332 3/16 2-3/8 2-3/4 0.210 2.350 ± 0.018 5.33 59.69 ± 0.46
333 3/16 2-1/2 2-7/8 0.210 2.475 ± 0.020 5.33 62.87 ± 0.51
334 3/16 2-5/8 3 0.210 2.600 ± 0.020 5.33 66.04 ± 0.51
335 3/16 2-3/4 3-1/8 0.210 2.725 ± 0.020 5.33 69.22 ± 0.51
336 3/16 2-7/8 3-1/4 0.210 2.850 ± 0.020 5.33 72.39 ± 0.51
337 3/16 3 3-3/8 0.210 2.975 ± 0.024 5.33 75.57 ± 0.61
338 3/16 3-1/8 3-1/2 0.210 3.100 ± 0.024 5.33 78.74 ± 0.61
339 3/16 3-1/4 3-5/8 0.210 3.225 ± 0.024 5.33 81.92 ± 0.61
340 3/16 3-3/8 3-3/4 0.210 3.350 ± 0.024 5.33 85.09 ± 0.61
341 3/16 3-1/2 3-7/8 0.210 3.475 ± 0.024 5.33 88.27 ± 0.61
342 3/16 3-5/8 4 0.210 3.600 ± 0.028 5.33 91.44 ± 0.71
343 3/16 3-3/4 4-1/8 0.210 3.725 ± 0.028 5.33 94.62 ± 0.71
Actual Dimensions
Inches Metric
344 3/16 3-7/8 4-1/4 0.210 3.850 ± 0.028 5.33 97.79 ± 0.71
345 3/16 4 4-3/8 0.210 3.975 ± 0.028 5.33 100.97 ± 0.71
346 3/16 4-1/8 4-1/2 0.210 4.100 ± 0.028 5.33 104.14 ± 0.71
347 3/16 4-1/4 4-5/8 0.210 4.225 ± 0.030 5.33 107.32 ± 0.76
348 3/16 4-3/8 4-3/4 0.210 4.350 ± 0.030 5.33 110.49 ± 0.76
349 3/16 4-1/2 4-7/8 0.210 4.475 ± 0.030 5.33 113.67 ± 0.76
350 3/16 4-5/8 5 0.210 4.600 ± 0.030 5.33 116.84 ± 0.76
351 3/16 4-3/4 5-1/8 0.210 4.725 ± 0.030 5.33 120.02 ± 0.76
352 3/16 4-7/8 5-1/4 0.210 4.850 ± 0.030 5.33 123.19 ± 0.76
353 3/16 5 5-3/8 0.210 4.975 ± 0.037 5.33 126.37 ± 0.94
354 3/16 5-1/8 5-1/2 0.210 5.100 ± 0.037 5.33 129.54 ± 0.94
355 3/16 5-1/4 5-5/8 0.210 5.225 ± 0.037 5.33 132.72 ± 0.94
356 3/16 5-3/8 5-3/4 0.210 5.350 ± 0.037 5.33 135.89 ± 0.94
357 3/16 5-1/2 5-7/8 0.210 5.475 ± 0.037 5.33 139.07 ± 0.94
358 3/16 5-5/8 6 0.210 5.600 ± 0.037 5.33 142.24 ± 0.94
359 3/16 5-3/4 6-1/8 0.210 5.725 ± 0.037 5.33 145.42 ± 0.94
360 3/16 5-7/8 6-1/4 0.210 5.850 ± 0.037 5.33 148.59 ± 0.94
361 3/16 6 6-3/8 0.210 5.975 ± 0.037 5.33 151.77 ± 0.94
362 3/16 6-1/4 6-5/8 0.210 6.225 ± 0.040 5.33 158.12 ± 1.02
363 3/16 6-1/2 6-7/8 0.210 6.475 ± 0.040 5.33 164.47 ± 1.02
364 3/16 6-3/4 7-1/8 0.210 6.725 ± 0.040 5.33 170.82 ± 1.02
365 3/16 7 7-3/8 0.210 6.975 ± 0.040 5.33 177.17 ± 1.02
366 3/16 7-1/4 7-5/8 0.210 7.225 ± 0.045 5.33 183.52 ± 1.14
367 3/16 7-1/2 7-7/8 0.210 7.475 ± 0.045 5.33 189.87 ± 1.14
368 3/16 7-3/4 8-1/8 0.210 7.725 ± 0.045 5.33 196.22 ± 1.14
369 3/16 8 8-3/8 0.210 7.975 ± 0.045 5.33 202.57 ± 1.14
370 3/16 8-1/4 8-5/8 0.210 8.225 ± 0.050 5.33 208.92 ± 1.27
371 3/16 8-1/2 8-7/8 0.210 8.475 ± 0.050 5.33 215.27 ± 1.27
372 3/16 8-3/4 9-1/8 0.210 8.725 ± 0.050 5.33 221.62 ± 1.27
373 3/16 9 9-3/8 0.210 8.975 ± 0.050 5.33 227.97 ± 1.27
374 3/16 9-1/4 9-5/8 0.210 9.225 ± 0.055 5.33 234.32 ± 1.40
375 3/16 9-1/2 9-7/8 0.210 9.475 ± 0.055 5.33 240.67 ± 1.40
376 3/16 9-3/4 10-1/8 0.210 9.725 ± 0.055 5.33 247.02 ± 1.40
377 3/16 10 10-3/8 0.210 9.975 ± 0.055 5.33 253.37 ± 1.40
378 3/16 10-1/2 10-7/8 0.210 10.475 ± 0.060 5.33 266.07 ± 1.52
379 3/16 11 11-3/8 0.210 10.975 ± 0.060 5.33 278.77 ± 1.52
380 3/16 11-1/2 11-7/8 0.210 11.475 ± 0.065 5.33 291.47 ± 1.65
381 3/16 12 12-3/8 0.210 11.975 ± 0.065 5.33 304.17 ± 1.65

382 3/16 13 13-3/8 0.210 12.975 ± 0.065 5.33 329.57 ± 1.65
383 3/16 14 14-3/8 0.210 13.975 ± 0.070 5.33 354.97 ± 1.78
384 3/16 15 15-3/8 0.210 14.975 ± 0.070 5.33 380.37 ± 1.78
Actual Dimensions
Inches Metric
385 3/16 16 16-3/8 0.210 15.955 ± 0.075 5.33 405.26 ± 1.91
386 3/16 17 17-3/8 0.210 16.955 ± 0.080 5.33 430.66 ± 2.03
387 3/16 18 18-3/8 0.210 17.955 ± 0.085 5.33 456.06 ± 2.16
388 3/16 19 19-3/8 0.210 18.955 ± 0.090 5.33 481.46 ± 2.29
389 3/16 20 20-3/8 0.210 19.955 ± 0.095 5.33 506.86 ± 2.41
390 3/16 21 21-3/8 0.210 20.955 ± 0.095 5.33 532.26 ± 2.41
391 3/16 22 22-3/8 0.210 21.955 ± 0.095 5.33 557.66 ± 2.41
392 3/16 23 23-3/8 0.210 22.940 ± 0.105 5.33 582.68 ± 2.67
393 3/16 24 24-3/8 0.210 23.940 ± 0.110 5.33 608.08 ± 2.79
394 3/16 25 25-3/8 0.210 24.940 ± 0.115 5.33 633.48 ± 2.92
395 3/16 26 26-3/8 0.210 25.940 ± 0.120 5.33 658.88 ± 3.05
400 1/4 1-3/8 1-7/8 0.275 1.350 ± 0.012 6.99 34.29 ± 0.30
401 1/4 1-1/2 2 0.275 1.475 ± 0.015 6.99 37.47 ± 0.38
402 1/4 1-5/8 2-1/8 0.275 1.600 ± 0.015 6.99 40.64 ± 0.38
403 1/4 1-3/4 2-1/4 0.275 1.725 ± 0.015 6.99 43.82 ± 0.38
404 1/4 1-7/8 2-3/8 0.275 1.850 ± 0.015 6.99 46.99 ± 0.38
405 1/4 2 2-1/2 0.275 1.975 ± 0.018 6.99 50.17 ± 0.46
406 1/4 2-1/8 2-5/8 0.275 2.100 ± 0.018 6.99 53.34 ± 0.46
407 1/4 2-1/4 2-3/4 0.275 2.225 ± 0.018 6.99 56.52 ± 0.46
408 1/4 2-3/8 2-7/8 0.275 2.350 ± 0.018 6.99 59.69 ± 0.46
409 1/4 2-1/2 3 0.275 2.475 ± 0.020 6.99 62.87 ± 0.51
410 1/4 2-5/8 3-1/8 0.275 2.600 ± 0.020 6.99 66.04 ± 0.51
411 1/4 2-3/4 3-1/4 0.275 2.725 ± 0.020 6.99 69.22 ± 0.51
412 1/4 2-7/8 3-3/8 0.275 2.850 ± 0.020 6.99 72.39 ± 0.51
413 1/4 3 3-1/2 0.275 2.975 ± 0.024 6.99 75.57 ± 0.61
414 1/4 3-1/8 3-5/8 0.275 3.100 ± 0.024 6.99 78.74 ± 0.61
415 1/4 3-1/4 3-3/4 0.275 3.225 ± 0.024 6.99 81.92 ± 0.61
416 1/4 3-3/8 3-7/8 0.275 3.350 ± 0.024 6.99 85.09 ± 0.61
417 1/4 3-1/2 4 0.275 3.475 ± 0.024 6.99 88.27 ± 0.61
418 1/4 3-5/8 4-1/8 0.275 3.600 ± 0.028 6.99 91.44 ± 0.71
419 1/4 3-3/4 4-1/4 0.275 3.725 ± 0.028 6.99 94.62 ± 0.71
420 1/4 3-7/8 4-3/8 0.275 3.850 ± 0.028 6.99 97.79 ± 0.71
421 1/4 4 4-1/2 0.275 3.975 ± 0.028 6.99 100.97 ± 0.71
422 1/4 4-1/8 4-5/8 0.275 4.100 ± 0.028 6.99 104.14 ± 0.71
423 1/4 4-1/4 4-3/4 0.275 4.225 ± 0.030 6.99 107.32 ± 0.76
424 1/4 4-3/8 4-7/8 0.275 4.350 ± 0.030 6.99 110.49 ± 0.76
425 1/4 4-1/2 5 0.275 4.475 ± 0.033 6.99 113.67 ± 0.84
426 1/4 4-5/8 5-1/8 0.275 4.600 ± 0.033 6.99 116.84 ± 0.84
427 1/4 4-3/4 5-1/4 0.275 4.725 ± 0.033 6.99 120.02 ± 0.84
428 1/4 4-7/8 5-3/8 0.275 4.850 ± 0.033 6.99 123.19 ± 0.84
429 1/4 5 5-1/2 0.275 4.975 ± 0.037 6.99 126.37 ± 0.94
Actual Dimensions
Inches Metric
430 1/4 5-1/8 5-5/8 0.275 5.100 ± 0.037 6.99 129.54 ± 0.94
431 1/4 5-1/4 5-3/4 0.275 5.225 ± 0.037 6.99 132.72 ± 0.94
432 1/4 5-3/8 5-7/8 0.275 5.350 ± 0.037 6.99 135.89 ± 0.94
433 1/4 5-1/2 6 0.275 5.475 ± 0.037 6.99 139.07 ± 0.94
434 1/4 5-5/8 6-1/8 0.275 5.600 ± 0.037 6.99 142.24 ± 0.94
435 1/4 5-3/4 6-1/4 0.275 5.725 ± 0.037 6.99 145.42 ± 0.94
436 1/4 5-7/8 6-3/8 0.275 5.850 ± 0.037 6.99 148.59 ± 0.94
437 1/4 6 6-1/2 0.275 5.975 ± 0.037 6.99 151.77 ± 0.94
438 1/4 6-1/4 6-3/4 0.275 6.225 ± 0.040 6.99 158.12 ± 1.02
439 1/4 6-1/2 7 0.275 6.475 ± 0.040 6.99 164.47 ± 1.02
440 1/4 6-3/4 7-1/4 0.275 6.725 ± 0.040 6.99 170.82 ± 1.02
441 1/4 7 7-1/2 0.275 6.975 ± 0.040 6.99 177.17 ± 1.02
442 1/4 7-1/4 7-3/4 0.275 7.225 ± 0.045 6.99 183.52 ± 1.14
443 1/4 7-1/2 8 0.275 7.475 ± 0.045 6.99 189.87 ± 1.14
444 1/4 7-3/4 8-1/4 0.275 7.725 ± 0.045 6.99 196.22 ± 1.14
445 1/4 8 8-1/2 0.275 7.975 ± 0.045 6.99 202.57 ± 1.14
446 1/4 8-1/2 9 0.275 8.475 ± 0.055 6.99 215.27 ± 1.40
447 1/4 9 9-1/2 0.275 8.975 ± 0.055 6.99 227.97 ± 1.40
448 1/4 9-1/2 10 0.275 9.475 ± 0.055 6.99 240.67 ± 1.40
449 1/4 10 10-1/2 0.275 9.975 ± 0.055 6.99 253.37 ± 1.40
450 1/4 10-1/2 11 0.275 10.475 ± 0.060 6.99 266.07 ± 1.52
451 1/4 11 11-1/2 0.275 10.975 ± 0.060 6.99 278.77 ± 1.52
452 1/4 11-1/2 12 0.275 11.475 ± 0.060 6.99 291.47 ± 1.52
453 1/4 12 12-1/2 0.275 11.975 ± 0.060 6.99 304.17 ± 1.52
454 1/4 12-1/2 13 0.275 12.475 ± 0.060 6.99 316.87 ± 1.52
455 1/4 13 13-1/2 0.275 12.975 ± 0.060 6.99 329.57 ± 1.52
456 1/4 13-1/2 14 0.275 13.475 ± 0.070 6.99 342.27 ± 1.78
457 1/4 14 14-1/2 0.275 13.975 ± 0.070 6.99 354.97 ± 1.78
458 1/4 14-1/2 15 0.275 14.475 ± 0.070 6.99 367.67 ± 1.78
459 1/4 15 15-1/2 0.275 14.975 ± 0.070 6.99 380.37 ± 1.78
460 1/4 15-1/2 16 0.275 15.475 ± 0.070 6.99 393.07 ± 1.78
461 1/4 16 16-1/2 0.275 15.955 ± 0.075 6.99 405.26 ± 1.91
462 1/4 16-1/2 17 0.275 16.455 ± 0.075 6.99 417.96 ± 1.91
463 1/4 17 17-1/2 0.275 16.955 ± 0.080 6.99 430.66 ± 2.03
464 1/4 17-1/2 18 0.275 17.455 ± 0.085 6.99 443.36 ± 2.16
465 1/4 18 18-1/2 0.275 17.955 ± 0.085 6.99 456.06 ± 2.16
466 1/4 18-1/2 19 0.275 18.455 ± 0.085 6.99 468.76 ± 2.16
467 1/4 19 19-1/2 0.275 18.955 ± 0.090 6.99 481.46 ± 2.29

468 1/4 19-1/2 20 0.275 19.455 ± 0.090 6.99 494.16 ± 2.29
469 1/4 20 20-1/2 0.275 19.955 ± 0.095 6.99 506.86 ± 2.41
470 1/4 21 21-1/2 0.275 20.955 ± 0.095 6.99 532.26 ± 2.41
Actual Dimensions
Inches Metric
471 1/4 22 22-1/2 .275 21.955 ± .100 6.99 557.66 ± 2.54
472 1/4 23 23-1/2 .275 22.940 ± .105 6.99 582.68 ± 2.67
473 1/4 24 24-1/2 .275 23.940 ± .110 6.99 608.08 ± 2.79
474 1/4 25 25-1/2 .275 24.940 ± .115 6.99 633.48 ± 2.92
475 1/4 26 26-1/2 .275 25.940 ± .120 6.99 658.88 ± 3.05
901 .056 .185 ± .005 1.42 4.70 ± .13

902 .064 .239 ± .005 1.63 6.07 ± .13
903 .064 .301 ± .005 1.63 7.65 ± .13
904 .072 .351 ± .005 1.83 8.92 ± .13
905 .072 .414 ± .005 1.83 10.52 ± .13
906 .078 .468 ± .005 1.98 11.89 ± .13
907 .082 .530 ± .007 2.08 13.46 ± .18
908 .087 .644 ± .009 2.21 16.36 ± .23
909 .097 .706 ± .009 2.46 17.93 ± .23
910 .097 .755 ± .009 2.46 19.18 ± .23
911 .116 .863 ± .009 2.95 21.92 ± .23
912 .116 .924 ± .009 2.95 23.47 ± .23
913 .116 .986 ± .010 2.95 25.04 ± .25
914 .116 1.047 ± .010 2.95 26.59 ± .25
916 .116 1.171 ± .010 2.95 29.74 ± .25
918 .116 1.355 ± .012 2.95 34.42 ± .30
920 .118 1.475 ± .014 3.00 37.47 ± .36
924 .118 1.720 ± .014 3.00 43.69 ± .36
928 .118 2.090 ± .018 3.00 53.09 ± .46
932 .118 2.337 ± .018 3.00 59.36 ± .46
O-RING CORD
STANDARD O-RING CORD
NOMINAL CROSS SECTION (IN) ACTUAL CROSS SECTION (IN) TOLERANCE (IN)
1/16 0.063 0.005
1/16 0.070 0.007
3/32 0.093 0.007
3/32 0.103 0.007
1/8 0.125 0.007
1/8 0.139 0.007
3/16 0.188 0.007
3/16 0.210 0.007
1/4 0.250 0.008
1/4 0.275 0.008
5/16 0.313 0.008
3/8 0.375 0.010
7/16 0.437 0.012
1/2 0.500 0.015
9/16 0.562 0.015
5/8 0.625 0.015
3/4 0.750 0.015
7/8 0.875 0.020
1 1.000 0.020
1 1/16 1.062 0.030
1 1/8 1.125 0.030
1 1/4 1.250 0.040
1 1/2 1.500 0.060
METRIC O-RING CORD

DIAMETER (MM) DIAMETER (IN) TOLERANCE (MM)
2.0 0.079 +/- 0.10
2.5 0.098 +/- 0.10
3.0 0.118 +/- 0.12
3.5 0.139 +/- 0.15
4.0 0.158 +/- 0.15
4.5 0.177 +/- 0.15
5.0 0.197 +/- 0.20
5.7 0.224 +/- 0.25
6.0 0.236 +/- 0.25
7.0 0.275 +/- 0.25
7.5 0.295 +/- 0.25
8.4 0.330 +/- 0.25
9.0 0.354 +/- 0.25
10.0 0.393 +/- 0.25
12.0 0.472 +/- 0.45
14.0 0.550 +/- 0.50
STANDARD O-RING KIT
70 DURO BLACK 30 SIZES, 382 PCS AS568 STANDARD SIZES
This kit contains 382 O-Rings in the 30 most popular sizes,

providing an extremely low cost per size value. O-Rings
conform dimensionally to AS568 universal series. Standard kit
material is 70-duro buna. Kits are available in a wide variety of
compounds and durometers.
KIT CONTENTS
NOMINAL REF ACTUAL SIZE
DASH # KIT QTY CS ID OD CS ID
-006 20 1/16 1/8 1/4 .070" .114"
-007 20 1/16 5/32 9/32 .070" .145"
-008 20 1/16 3/16 5/16 .070" .176"
-009 20 1/16 7/32 11/32 .070" .208"
-010 20 1/16 1/4 3/8 .070" .239"
-011 20 1/16 5/16 7/16 .070" .301"
-012 20 1/16 3/8 1/2 .070" .364"
-110 13 3/32 3/8 9/16 .103" .362"
-111 13 3/32 7/16 5/8 .103" .424"
-112 13 3/32 1/2 11/16 .103" .487"
-113 13 3/32 9/16 3/4 .103" .549"
-114 13 3/32 5/8 13/16 .103" .612"
-115 13 3/32 11/16 7/8 .103" .674"
-116 13 3/32 3/4 15/16 .103" .737"
-210 10 1/8 3/4 1 .139" .734"
-211 10 1/8 13/16 1-1/16 .139" .796"
-212 10 1/8 7/8 1-1/8 .139" .859"
-213 10 1/8 15/16 1-3/16 .139" .921"
-214 10 1/8 1 1-1/4 .139" .984"
-215 10 1/8 1-1/16 1-5/16 .139" 1.046"
-216 10 1/8 1-1/8 1-3/8 .139" 1.109"
-217 10 1/8 1-3/16 1-7/16 .139" 1.171"
-218 10 1/8 1-1/4 1-1/2 .139" 1.234"
-219 10 1/8 1-5/16 1-9/16 .139" 1.296"
-220 10 1/8 1-3/8 1-5/8 .139" 1.359"
-221 10 1/8 1-7/16 1-11/16 .139" 1.421"
-222 10 1/8 1-1/2 1-3/4 .139" 1.484"
-325 7 3/16 1-1/2 1-7/8 .210" 1.475"
-326 7 3/16 1-5/8 2 .210" 1.600"
-327 7 3/16 1-3/4 2-1/8 .210" 1.725"
METRIC O-RING KIT
70 DURO BLACK 32 SIZES, 401 PCS METRIC SIZES
This Metric O-Ring kit contains 401, 70 Durometer

O-Rings in 32 different sizes mostly used in industrial and
automotive type applications. An extremely valuable kit
to have in the warehouse or maintenance department.
Standard kit material is 70-duro buna. Kits are available in
a wide variety of compounds and durometers.
KIT CONTENTS
ACTUAL SIZE
CS ID KIT QTY
1 3 19
1 3 19
1 4 17
2 5 9
2 6 17
2 8 17
2 10 17
2 11 17
2 12 17
2 14 17
2 17 17
2 20 17
3 10 12
3 12 12
3 16 12
3 18 12
3 22 12
4 20 9
4 22 9
4 24 9
4 25 9
4 30 9
4 34 9
4 36 9
4 40 9
4 45 9
4 47 9
4 50 9
5 16 7
5 25 7
5 25 7
5 30 7
5 32 7
5 35 7
NITRILE SPLICING KIT
70 DURO BLACK 5 PIECES, 7 FEET EACH
The splicing kit for on the job repairs with rapid set
adhesives. This Splicing kit will enable you to construct
rings to your custom requirements. There are no special
skills required, just follow instructions. This kit contains
everything you need to produce a perfect o-ring. Standard
kit material is 70-duro buna. Kits are available in a wide
variety of compounds and durometers.
CONTENTS • Stock of O-ring Cord

• Razor Blade
• Cutting JIG
• Tube of Adhesive
• Instructional Card
LENGTH (FT) CS (IN) CS (MM)

7 .070 1.78
7 .103 2.62
7 .139 3.53
7 .210 5.33
7 .275 6.99

O-Rings: (Buna N)

Uploaded by

Copyright:

Available Formats

O-Rings: (Buna N)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

O-Rings: (Buna N)

Uploaded by

Copyright:

Available Formats

O-RINGS

NITRILE O-RING OVERVIEW (Buna N)

CURE SYSTEM: SULFUR-CURED

ISO/DIN 1629 DESIGNATION NBR HARDNESS RANGE 40 to 90 Shore A

PERFORMS WELL IN DOESN'T PERFORM WELL IN

CURE SYSTEM: BISPHENOL-CURED

OTHER COMMON VARIATIONS

ISO/DIN 1629 DESIGNATION FKM HARDNESS RANGE 50 to 90 Shore A

ASTM D2000/ SAE J 200 CODES HK RELATIVE COST High

PERFORMS WELL IN DOESN'T PERFORM WELL IN

CURE SYSTEM: SULFUR-CURED

OTHER COMMON VARIATIONS

ISO/DIN 1629 DESIGNATION CR HARDNESS RANGE 30 to 90 Shore A

ASTM D2000/ SAE J 200 CODES BC, BE RELATIVE COST Low

TEST REPORT FOR COMPOUND C70 DUROMETER: 70 COLOR: BLACK

CURE SYSTEM: PEROXIDE-CURED

OTHER COMMON VARIATIONS

ISO/DIN 1629 DESIGNATION EPM, EPDM HARDNESS RANGE 30 to 90 Shore A

TEST REPORT FOR COMPOUND E70 DUROMETER: 70 COLOR: BLACK

*American Society for Testing and Materials

CURE SYSTEM: PEROXIDE-CURED

OTHER COMMON VARIATIONS

BEHAVIOR IN PRESENCE OF FOREIGN AGENTS

PROPERTIES RESULTS ASTM* TEST METHOD

Density 2.14 - 2.18 g/cm3 D792

*American Society for Testing and Materials

CURE SYSTEM: PEROXIDE-CURED Standard PU compounds are peroxide‐cured.

OTHER COMMON VARIATIONS

ISO/DIN 1629 DESIGNATION AU, EU HARDNESS RANGE 60 to 93 Shore A

ASTM D2000/ SAE J 200 CODES BG RELATIVE COST Medium to High

PERFORMS WELL IN DOESN'T PERFORM WELL IN

*American Society for Testing and Materials

TENSILE SET: Hold 100% Elongation for 2

*American Society for Testing and Materials

381 3/16 12 12-3/8 0.210 11.975 ± 0.065 5.33 304.17 ± 1.65

466 1/4 18-1/2 19 0.275 18.455 ± 0.085 6.99 468.76 ± 2.16

467 1/4 19 19-1/2 0.275 18.955 ± 0.090 6.99 481.46 ± 2.29

901 .056 .185 ± .005 1.42 4.70 ± .13

METRIC O-RING CORD

This kit contains 382 O-Rings in the 30 most popular sizes,

This Metric O-Ring kit contains 401, 70 Durometer

CONTENTS • Stock of O-ring Cord

LENGTH (FT) CS (IN) CS (MM)

You might also like