Dokumen Pioneer-Rsm400

5/23/2018 Pioneer RSM400-slidepdf.
com
ORDER
RRV40
X-RSM400DV
DVD MINI COMPONENT SYSTEM
X-RSM400DV
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
DVD
Model Type Power Requirement Serial No. Remarks
Region No.
X-RSM400DV LXCN AC 110 V to 240 V 3 &&&&######LE LE : ASEAN
X-RSM400DV DXCN AC 110 V to 240 V 4 &&&&######ME ME : LATIN AMERICA
X-RSM400DV DXCNRI AC 110 V to 240 V 2 &&&&######RB RB : MIDDLE EAST
For details, refer to "Important Check Points for good servicing".
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2009
http://slidepdf.com/reader/full/pioneer-rsm400 1/69
T-ZZV NOV. 2009 Printed in J
5/23/2018 1 2 Pioneer RSM400-slidepdf.com
3 4
LASER DIODE CHARACTERISTICS

For DVD Wave Length: 656 nm
C
Operating output: 0.1 mW CW, Class 1
Maximum output: Class 1
For CD Wave Length: 789 nm

Operating output: 0.15 mW CW, Class 1
Maximum output: Class 1
2 X-RSM400DV
1 2 3 4
5/23/2018 5 Pioneer
6 RSM400-slidepdf.com 7 8
[Important Check Points for Good Servicing]

In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity.(Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
a Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
3. Lubricants, Glues, and Replacement parts

Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
X-RSM400DV
5 6 7 8
5/23/2018 Pioneer RSM400-slidepdf.com
SECTION 5. DIAGNOSIS CONNECTION ………………………...….…..…………….. 5-1
1-1
SECTION 1. GENERAL
SERVICING PRECAUTIONS
NOTES REGARDING HANDLING OF THE PICK-UP
1. Notes for transport and storage
1) The pick-up should always be left in its conductive bag until immediately prior to use.
2) The pick-up should never be subjected to external pressure or impact.
Storage in conductive bag Drop impact
2. Repair notes
1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic mate-
rials.
2) The pick-up should always be handled correctly and carefully, taking care to avoid external pressure
and impact. If it is subjected to strong pressure or impact, the result may be an operational malfunc-
tion and/or damage to the printed-circuit board.
3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that
reason the adjustment point and installation screws should absolutely never be touched.
4) Laser beams may damage the eyes!
Absolutely never permit laser beams to enter the eyes!
Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged.
NEVER look directly at the laser beam, and don’t allow
contact fingers or other exposed skin.
5) Cleaning the lens surface
If there is dust on the lens surface, the dust should be cleaned away by using an air bush (such as
used for camera lens). The lens is held by a delicate spring. When cleaning the lens surface, there-
fore, a cotton swab should be used, taking care not to distort this.
Pressure
Magnet
Pressure
How to hold the pick-up
Cotton swab
Conductive Sheet
6) Never attempt to disassemble the pick-up.
Spring by excess pressure. If the lens is extremely dirty, apply isopropyl alcohol to the cotton swab.
(Do not use any other liquid cleaners, because they will damage the lens.) Take care not to use too
much of this alcohol on the swab, and do not allow the alcohol to get inside the pick-up.
1-2
NOTES REGARDING COMPACT DISC PLAYER REPAIRS

1. Preparations
1) Compact disc players incorporate a great many ICs as well as the pick-up (laser diode). These compo-
nents are sensitive to, and easily affected by, static electricity. If such static electricity is high voltage,
components can be damaged, and for that reason components should be handled with care.
2) The pick-up is composed of many optical components and other high-precision components. Care
must be taken, therefore, to avoid repair or storage where the temperature of humidity is high, where
strong magnetism is present, or where there is excessive dust.
2. Notes for repair

1) Before replacing a component part, first disconnect the power supply lead wire from the unit
2) All equipment, measuring instruments and tools must be grounded.
3) The workbench should be covered with a conductive sheet and grounded.
When removing the laser pick-up from its conductive bag, do not place the pick-up on the bag.
(This is because there is the possibility of damage by static electricity.)
4) To prevent AC leakage, the metal part of the soldering iron should be grounded.
5) Workers should be grounded by an armband (1M )
6) Care should be taken not to permit the laser pick-up to come in contact with clothing, in order to
prevent static electricity changes in the clothing to escape from the armband.
7) The laser beam from the pick-up should NEVER be directly facing the eyes or bare skin.
Armband
Resistor
(1 M )
Resistor
(1 M ) Conductive
Sheet
1-3
SAFETY PRECAUTIONS
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated
circuits and some field-effect transistors and semiconductor chip components. The following techniques should
be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off
any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device, which should be removed for potential shock reasons
prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive
surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can
generate electrical charges sufficient to damage ESD devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD
devices.
6. Do not remove a replacement ESD device from its protective package until immediately before you are
ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive materials).
7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the
protective material to the chassis or circuit assembly into which the device will by installed.
CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL OTHER

SAFETY PRECAUTIONS.
8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate
static electricity sufficient to damage an ESD device).
CAUTION. GRAPHIC SYMBOLS
THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN AN EQUILATERAL TRIANGLE, IS

INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED
“DANGEROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF
ELECTRIC SHOCK.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE

SERVICE PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE
LITERATURE.
1-4
When Option Code Assembly

is replaced, perform this
Option Code setting.
NAME HEX
OPT 0 F5
OPT 1 00
OPT 2 A4
OPT 3 AD
OPT 4 00
OPT 5 09
OPT 6 83
OPT 7 20
OPT 8 60
OPT 9 00
X-RSM400DV/DXCN X-RSM400DV/DXCNRI
NAME HEX
OPT 0 F5
OPT 1 00
OPT 2 A4
OPT 3 BD
OPT 4 00
OPT 5 69
OPT 6 83
OPT 7 20
OPT 8 60
OPT 9 00
X-RSM400DV/LXCN
PROGRAM DOWNLOAD GUIDE
Caution) Do not perform any other work such as disconnecting USB device, switching to the Function
and turning off the power while downloading it to the set.
The USB device should be disconnected after completing the download.
• AUDIO USB DOWNLOAD GUIDE
1. When the USB device is inserted on the USB function, is displayed on the screen after a while.
“File : MDT404_YYMMDDX.HEX” * x: version.
2. The message “Upgrade” is displayed while downloading.
3. The power is automatically turned off when downloading is completed.
• DVD USB DOWNLOAD GUIDE
The program file to download should be named as LG_MDT404XXX_YYMMDDX.rom.
- The downloaded file should be modified as LG_MDT404XXX_YYMMDDX.rom.
- After safely storing LG_MDT404XXX_YYMMDDX.rom at the USB device, perform the following steps.
1. When the USB device is inserted at the USB function, the screen is changed into downloading
screen.
2. When downloading is completed, the message “Completed” is displayed at the top left on the screen.
3. Turn on the power, press the SETUP button of the remote controller on the USB FUCTION. When
the SETUP window is displayed on the screen, move down once to select the DISPLAY menu. Go
to the TV Aspect on the right menu, move to “16:9”, enter “1397139” by using the numeric key of the
remote controller, and press the Enter key.
Then, the System Information screen is displayed. If not, retry the steps at the above.
4. When Step 3 is completed, press the Pause key of the remote controller.
5. Disconnect the power cord, and reconnect it after 5 seconds to complete downloading.
6. When the power is turned on, the language selection menu is initially displayed.
After selecting the desired language, press the SELECT/ ENTER.
1-6
SPECIFICATIONS
General
Power supply AC 110 V~240 V, 50 Hz/60 Hz
Power consumption 65 W
Net Weight 5.8 kg

External dimensions (WxHxD) 273 x 336 x 372 mm
Operating temperature 5 °C to 35 °C
Operating humidity 5% to 85 %
Tuner
FM Tuning Range 87.5 ~ 108.0 MHz
AM Tuning Range 530 ~ 1 700 KHz (DXCN), 531 ~ 1 602 KHz (LXCN/DXCNRI)
Amplifier
Output Power Front : 110 W x 2, Sub Woofer : 180 W
T.H.D 10 %
Frequency Response 42 ~ 20000 Hz
Signal-to-noise ratio 75 dB
DVD / CD player
Frequency response (audio) 40 ~ 20,000 Hz
Signal-to-noise ratio (audio) More than 75 dB (1 KHz)
Signal-to-noise ratio (video) More than 55 dB (1 KHz)
Dynamic range (audio) More than 80 dB
Video output 1.0 V (p-p), 75
Component Video output (Y) 1.0 V (p-p), 75
(Pb)/(Pr) 0.7 V (p-p), 75
Cassette tape player

F.F/REW Time 120 sec (C-60)
Frequency Response 250 ~ 8000 Hz
Signal to Noise Ratio 43 dB
Channel Separation 45 dB (P/B) / 45 dB (R/P)
Erase Ratio 50 dB (MTT-5511)
Speakers FRONT SPEAKER SUBWOOFER SPEAKER

Type 2 Way 2 Speaker 1 Way 1 Speaker
Impedance 4 3
Input Power 110 W 180 W
Max. Input Power 200 W 300 W
Net Dimensions (W x H x D) 220 x 336 x 296 mm 274 x 336 x 336 mm
Net Weight (1EA) 4.5 kg 6.0 kg
Designs and specifications are subject to change without pior notice.
1-7
1-8
E
R 4
L 4
4 2 4
+
S
N S E E 4 L 4 4 4
4 L
Y
E N L W L W 4 E 4 L R N N S E
/ E
S O O A D C W C L L C O O S G
G G G
A I I E E C I I C W I W R
G
C E E A I
e P P G I G
G S P R N G G P G G G R P
l
b 4 2 I D N
S 5 A I L I C 2 C R N
I N I I I A 8
u 8 3 P P E 8 8 M A R P P E 1
o 5 2 7 8 R 5 E R O R R M 5
P P R 1 R E P 6 8 G 5
D 1 1 5 5 P 1 G P
S M S S A 3 A G S 7 4 1
r 3
- 4
- 2 2 4
- N - 2 7 N 4
-
a 3 3 4
- 4
- N 3 O N N N N N 3 N N N 4 - 4
- 3
e
N y 9 9 3 3 O 9 E O O O O O 9 O O O 3 3 O E 9
0
- 0
- 8 8 E 0
- G E E E E E 0
- 8 9 G 0
E E E 0 -
O 0 0 0
7 0 0 - - G 0 I G G G G G 0 G G G - - I 0
I 0
T 5 5 2 2 I 5 P I I I I I 5 I I I 2 0 P 5
A 1 4 2 0 0 P 5 6 P P P P P 2 P P P 0 5 0 8
0 8 3 7 8 9 8 2 8 4 1 8 6 8 2 8 8 6 8 2 1
C 6 5 2 5 5 0 5 2 9 1 0 8 1 5 7 2 7 7 4 3 5
I F 1 1 2 2 3 1 1 5 0 6 6 0 1 0 4 6 2 7 1 1
F
I F 3
- 4
- 4
- 4
- 4
- 4
- 4
- 4
- 4
- 4
- 4
- 3
- 3
- 4
- 4
- 4
- 4
- 4
- 3
- 4
-
T C 2
4 3 3 3 3 0 3 2 2 9 1 2 8 3 9 2 1 3 3 1 3
S
I E P 0
P W 9
- 0
9
- 0
8
- 0
8
- 1
6
- 0
9
- 2
- 0
8
- 2
1
- 0
8
- 0
8
- 2
6
- 0
9
- 2
3
- 2
- 0
8
- 0
8
- 0
9
- 2
- 0
9
-
L 0 0 2 2 3 0 0 1 0 1 1 0 0 0 0 1 2 0 0 0
S C 5 5 0 0 3 5 5 0 5 0 0 5 5 5 5 0 0 5 5 5
S
T s t
s s t
s s t
s s t
s s t
s s t
s s t
s s t
s s t
s s t
s
R t
r r t
r r t
r r t
r r t
r r t
r r t
r r t
r r t
a a a a a a a a a a a a a a a a a a a a
r r t
r r
A P P P P P P P P P P P P P P P P P P P P
P N m m m m m m m m m m m m m m m m m m m m
) O i s i
s i
s i
s i s i
s i s i
s i
s i
s i
s i
s i
s i
s i
s i
s i
s i s i
s i s
K I n n n n n n n n n n n n n n n n n n n n
a a a a a a a a a a a a a a a a a a a a
C T k h h h h h h h h h h h h h h h h
P c c c c c c c c c c c c c c c c c c c c c h h h h
E I e e e e e e e e e e e e e e e e e e e e e
D M M M M M M M M M M M M M M M M M M M M
D R
C i
o
S d k k k k k k k k k k k k k k k k k k k k
c c c c c c c c c c c c c c c c c c c c
S
/ E u e e e e e e e e e e e e e e e e e e e e
D A D D D D D D D D D D D D D D D D D D D D
A
T 1 B
1 B
A F C A A A B C J P M C A
P N A B 3
H . 0 5 1 1 3 4 1 1 1 2 1 4 1 1 1 1 3 5 J
8 0
P 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
P 0
G O 1
I 7 U P P P P P P
G P P P P
S P P
G P P P P P
V G P
7 Z E
- B
- B
- P
- Q
- Z S
- M
- S
- Z A
- Z A
- G
- S
- B
- Z Z J
-
R N
( 5
T 3 R R R R R R R R R R R R R R R R R R R R
Z 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
K R A 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7
A E 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
C P
.
E O
D N 0 1 2
. 1 2 3 6 7 8 9 1 3 5 6 7 8 9 0 2 3 5
E A 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 2 2 2 2
P C A A A 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
A O
T L
Y
R
A
S
S
E
C
E
1 N
0 N
E
A D H
E W
D
D R
A E
E T
T
B U
Y L
A F
M
W
W O
F W
0
G
N R
I O
R F
6
-
2
0 2
5
9 2
1 0
0
8
1
0
3
2
0
7
1
0
5
-
1
5
6 0 2
1
0
6
0
0
2
2
0
D 7 8

E Y 0 0
G R
N A 0 0
A S
H S
C E
E C
E
B N
Y
A N
M E
Y H
E
L W
2
0
)
L R
U E
P T
T
A
K
R U
O L
T F

C
O
M W
O
S
E S W
A R
R O
D B F
W S
/
E A
I
V T
H
D I
G
E R
D :
L
O S
/
P A
X & 2
0
E /
S
0
M A
(
S
I M
N S
I
A N
H A 9 3
1
C H 0
0 0
E C
E 1
M M
0
0
A
0
0
3
0
K K 0
C C
E E
D D 1
1
0
E E 9
P P
0
0
A
A T
T 1
.
. -
2 2
E 4 4 2 4

S R L 4
4 L
+ S E 4 4 4 L Y
S e A L W L W 4 E 4 4
L R N N S E
/ D C W C L G L R C O O S G
g C I
A i C G G W P W C G G G A I
I E E
e p S R G
l N D I N C 2 C R I
N I N I I R
P
b 6 S A I A 6
u 3 E E R L R R M 8 M A R P P E 8
o 2 R G P O P P R 5 R E P 6 8 G 5
1
D 4 P 1 G S 2 7 N 1
7 4
r - N S M S S A 3
- A 4
-
a 3 N O N N N N N 3 N N N 4 - 4
- 3
e 9 O E O O O O O 9 O O O 3 3 O 9
N y 0
- E E E E E E 0
- E E E 8 9 E 0
-
G
O 7 0 G I 0 0
- 0
- G 0
I
I G G G G G G G G
T 0 5 I P I I I I I 5 I I I 2 0 P 5
P 6 P P P P P 2 P P P 0 5 0 6
A 1 6
0 3 9 2 8 4 1 8 6 8 2 8 8 6 8 2 8
I 6
C 2 0 2 9 1 0 8 1 5 7 2 7 7 4 3 5
F F 1 3 1 5 0 6 6 0 1 0 4 6 2 7 1 1
F 4
I - 4
- 4
- 4
- 4
- 4
- 4
- 3
- 3
- 4
- 4
- 4
- 4
- 4
- 3
- 4
-
C 2
4 3 0 2 2 9 1 2 8 3 9 2 1 3 3 1 3
T E P 9
P W 0
6 2 8 1 8 8 6 9 3 2 8 8 9 2 9
- 1
- 2
- 0
- 2
- 0
- 0
- 2
- 0
- 2
- 2
- 0
- 0
- 0
- 2
- 0
-
S
I S C 0 3 0 1 0 1 1 0 0 0 0 1 2 0 0 0
5 3 5 0 5 0 0 5 5 5 5 0 0 5 5 5
L
S
T s t
t s s t
r r t
s s t
r r t
s s t
r r t
s s t
r r t
s s t
r r t
s s t
r r t
s s t
r r t
s
r r
R a P
P a P
a P
a P
a P
a P
a P
a P
a P
a P
a P
a P
a P
a P
a P
a
A N m m m m m m m m m m m m m m m m
P O i s i
s i s i
s i
s i s i
s i s i
s i
s i
s i
s i
s i
s i
s i
s
) I n n n n n n n n n n n n n n n n
K T k a h
a a a a a a a a a a a a a a a
P c h h h h h h h h h h h h h h h
e e e e e e e e e e e e e e e e c
C R D
I c c c c c c c c c c c c c c c
e
E C i M M M M M M M M M M M M M M M M
o k k k k k k k k k k k k k k k k
D S d c c c c c c c c c c c c c c c c
u e e e e e e e e e e e e e e e e
S E
/ D A D D D D D D D D D D D D D D D D
A 1 C A A F C A A A B C J P M C A D
T . 0 2 3
0
3 1
0 0 1 1 2 1 4 1 1 1 1 3 5 2
0 0 0 0 0 0 0 0 0 0 0
F O 8
1 P 0
P P P 0
P P P P P P P P P P P P
E N 7
7 H P G S M S S A G A G S B V G J
Z - Z - - - Z - Z - - - - Z Z Z
L
( T 5
3 R R R R R R R R R R R R R R R R
8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8
R Z 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
K A E
A 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
C P
.
E O
D N 0 3
3 7 8 9 3 5 6 7 8 9 0 2 3 4
.
E A 0 0 0 0 0 0 1
1 1 1 1 1 1 1 2 2 2 2
P C A A 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
A L
O
T
Y
R
A
S
S
E
C
E
N
N
E
D H
E
D W
D R
A E 4
E T 2
T
B U 0
8
Y L
A F
-
M
W
W
F O
G
N
W
R
2
I O
R F
0
2
0
5
1
0
9 3
1 2
0 0
8
1
0
2
2
7
-
0 2
7
1
0
6
1
0
3
0
A
)
K
C
E 7
D 0
0
8
0
0
S
/
A
T
F
E
L
:
S
/
A
&
S
/
A
(
M
S
I 9
0 3
0
N 1
0
A
H
C
E 9
M 0
0
K
C 1
E 1
0
D 3
E 0
0
0
0
P A
A
T
.
2
-
2
t
r K
a R
P A P
e M S
c E N
i
v R
r
e
S
t
o
N 5
: S D 5 H
S A 3 i M C D 1 1 3 M l 3 t
P
A
s M M 3 V N C H - 0
H
5 V e D C
M 1 s
S H / /
M D K K
C r I
1
7
I
D A Y - p
M 1 p D b L
O
E
i /
K
7 u
1 D S
N t R E M M
p E E e 1 A C C A 1 A M L D D H
- u A A M / d
a C H
- A
e P 0 g C H E E M H
- H L C C M H H 3 K o E H M
D x M
/ n
a V C D D - M C A U (
( S C C 1 C L D M
P 5 N D S E E 7 E V C M
t
r U 3 K
C h F E
c R M 3 3 3 V E H P
C A G C
( E
3
1 D 0 3 D E 7
o P 0
. E 3 9 / 0 0 0
- - 7 D M
/ E N W R M
/ M
/ 0 M M
- C /
h I O P P - C 7
K K H
S M 0
- D 3 7 K 0 0 3 K M H D
2 2 1 1 C C M F
1 0 F K M
0
A 1 1 S - 7 C /
- C F F h C A D U 3 - 2
6 h 6 C 6
.
D
V L x R K
E 7 S E L L m 1 E C E O U U 1
- E E V 0 d
0
F 0
L 0 E 2
D S 3
V
- R C 5
x B
B H
1
- M 1
C D T
A T
A d
c H
- 0
D D
E K
M E
/ L - E
P E
P d
p D 0
3 D 0
D 5
- c
m T
A 5
- 0
D B
+
0
7 1 U 0 I I 8 0
- 8 8 N I I N 8
N 3 T 5 O M 3 C n M M 8
. O
x R M 1 4 P P I
V C - E E D D - R E M i
a O O 0 0 3 3
- G D P
2 - F
G
E X 3 H
O
I G M 1 5
- L D V R C F E D O
H m H H C G F F X F
T L I H
- E Y F X K K U R H B 3 C 0 H H A U K A H W
P
A 3 3 3
- T 1
M 0 S M M A E S B M M 0 M M 5 M S S M A M M S
1 1 R E
C 7 7 V 6 U 7 9 B O O B G B U O O 7 O O S 4
I E O B B U A
E O U B 6
F 1 1 D 1
I - B 1 7 A P P T N
0 A A R P P 1 P P T P A A L 0 P L A 0
C H
- H
- E 3 D H
- S
- D D D 0 D D D D - D D S
H I
S R D D D D 0 D D D
0
-
r
E M M M 2
- L M S L L L 5
- H L L L L M L L E R L L L L 3
- L L L z
P V V O 0 O V M O O O F C O O O O D O O R E O O O O F O O O z
.
S D D H 1 s
M D C M M M R 3 M M M M C M M P F M M M M R M M M 1
y
l
b k k
c C c C
m e l
y D e D
e y
l D , D ,
s l
y b , b y ,
l y y
l
s y m
l b l y
l e b
N A b m b e b b t
i e
t
O m e s m r
r m i
t
I s C
m e s m s e m m e e p
e s
s e
T i
s e s
P n s
I s A F
F
s A
r s p A
s
s
s
s
F
,
t s
A
a
T
,
a
R h A p , e A U r A A r r e p r r r e r
e p r r o r r n e o w
C c e m l m B k y y t
a a t B a a a B a a t e g a e e e
d t a m v r
m v s i e
S e s a b
a l c a
a a C i r
l a
e e o C r e e e C e e l a l o a u o e r o c a
E M B C C D P P T G G M P T B G G P G G P M C C B G M G F C S
D
2 1 C B 1 1 1 1 1 1 1 1 1 A 1 A A 1 1 1 1 2 1 1 1 1 1 1
0 6
0 0
2 1
6 8
0 0 3
0 9
0 1
0 2
0 0 4
0 7
0 2
A
1 0
3 9 A 3 9
0 0
7 6 6
0 5
0 1
0 7
0
6 5
0
3 5
0 6
0 0 8
0 8
0 0
. 8
4 2 2 2 5 6 6 3
7 7 9 0 7 0 0
0 6 1 2 5 3 6 1 1
4 3 2
0 W
6 0 J 6 3 0 5 7
3
5 5 9 9 3 0 1 0
0 5 5 1 7 5 7 3 3 4
O 3 0 B - 2
0 0
N 0 6 0 7 1 7
1 8 8 7 2 0
- 0
- B 7 0
B
0 5
B 6 6 7 2
7 7 9
8 2 2 6 2
7 1
1 1 8 0 7 8 8 0 9 1 1 8 7 7
0 4 4 4 4 6 5 R R R 4 R R 3 3 3 4 5 4 4 5 5 5 0
T 7 7 R R 4 5 6
1 0 Q R Z S T T U R S 0 0 0 R 0 0 J B U K M A U T Q K 3
R P N 6 B
A F A 8 5 0 7 7 7 7
8 C B A J D D A B J 4 4 4 B 4 4 G A B C A E A D D C A
P A A 4 6 M E E M M M E E M 4 4 4 E 4 4 M R M M M M E M M M F
.
O
N
.
A A A B C
C 6 1 2 0 2 5 7 1 3 3 5 6 9 2 3 4 5 6 7 9 9 9 0 2 3 5 7 0 1 0 0
O 2 0 0 1 1 3 3 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 7 7 7 7 7 8 8 3
L A A A 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4
1
-
2
0 2
3 1
4 0
1 9
0 0 -
A 3
4 2
7
0 3
1 1
0 2
1
2 0
0
A
0 2
3 1
A B C 4 0
9 9 9
) 6
1
6
1
6
1
3 6
1 2
7 A
1 6
5
3
H
- 5
1
0
M 0
8
V 1
D
(
3
5
5
5
3
7
1 1 1
A
W 3
5 5
E
I 1 6
1 1
8
V 4
6 1
1
D
E
D
O
L
P
X
E
K 5
C 2 3
7
1
E 0
7 6 6
1 1
D 1
M
S
I 1
5
N 1 2
7
6
6
A 9
5
1 1
H 1 7
C 7
1
7
6
E 1
M
.
3
4. SPEAKER SECTION
(1) FRONT SPEAKER
A60L
A60R
LOCA. NO PART NO. DESCRIPTION SPECIFICATION REMARKS

A60L EAB61030301 Speaker Assembly MCS404 049-01368-07 EAW MCS404
A60R EAB61030201 Speaker Assembly MCS404F 049-01368-07 EAW MCS40
2-11
(2) PASSIVE SUBWOOFER
A90
LOCA. NO PART NO. DESCRIPTION SPECIFICATION REMARKS

A90 EAB61030401 Speaker Assembly MCS404W 049-01368-07 EAW MCS40
2-12
4. PACKING ACCESSORY SECTION

80 8 Battery
80 1 Instruction Ass'y
82 4 Antenna, Loop (AM)
90 0 Remote Controller 82 5 Antenna, T (FM)
811 RCA Cable, 1Pin(Black)
803FT Packing,
803 Packing, Main Set Front Speaker Top
803WT Packing, Woofer Top
804W Bag, Woofer 804F Bag, Front Speaker
804 Bag, Main Set 804F Bag, Front Speaker
803WB Packing,
Woofer Bottom
803FB Packing,
803 Packing, Main Set Front Speaker Bottom
80 2 Box
2-13
NOTES) If you want to purchase NOTES) Warning

Flash memory, you must order NOTES) Parts that are shaded are critical
"IC100A, IC503A" NOTES) With respect to risk of fire or
NOTES) electricial shock.
/DXCN ( Latin America)

MODEL: X-RSM400DV /LXCN ( ASEAN)
/DXCNRI ( Middle East)
. PACKING & ACCESSORY SECTION

S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS
801 AFN37125930 Manual Assembly,Owners HOME MDT404-A0.DPERPPK LG DXCN
802 MAY62411401 Box,Master BOX DW2 1141 414 442 3 COLOR M DXCN
803 MFZ47047395 Packing CUTTING EPS HOME THEATER MDT40
803WT MFZ61796892 Packing WOOF_TOP
803WB MFZ61796893 Packing WOOF_BOT
803FT MFZ61796894 Packing FRONT_TOP
803FB MFZ61796895 Packing FRONT_BOT
804 MAF37454613 Bag CUTTING EPE 630 600 0.5 EPE+HD
804W MAF61968002 Bag WOOF
804F MAF61968001 Bag FRONT
808 EAC42053701 Primary Cell Battery,Carbon Zi R03G(1EA Packing) R03 1.5V 0AH NSP
811 6850R-PAA8H Cable,Assembly 061104 RCA PLUG(3.2) RCA PLUG(
824 EAA56672101 Antenna,Loop SN080113AM SINGLE 4DB 10UH HW
825 5010R-T001D Antenna,T T13021F-2 SINGLE 0DB 0OHM 0 1.
. REMOTE CONTROLLER
900 AKB72913811 Remote Controller Assembly CB1 MDT404 MINI DVD Pioneer
CONTRAST TABLE
X-RSM400DV/DXCN, X-RSM400DV/DXCNRI and X-RSM400DV/LXCN are constructed the same except
for the following:
Ma rk No. Symbol and Description X-RSM400DV/DXCN X-RSM400DV/DXCNRI X-RSM400DV/LXCN Remark
801 Manual Assembly, Owners AFN37125930 AFN37125932 AFN37125931

802 Box,Ma s ter MAY62411401 MAY62411405 MAY62411404
2-14
2-12
SECTION 3. ELECTRICAL PART

AUDIO ELECTRICAL TROUBLESHOOTING GUIDE
1. POWER (SMPS)
POWER (SMPS)
YES
NO
Check the fuse Replace the fuse
F901
YES
Check
the DC V of C905 NO
Check BD901, LF901, 902
if DC V is over
400V
YES
Check the
DC V of C909,C903,C921 NO NO
If DC V is in 14~19V Check IC901, 902 Replace IC901,902
and it is steady
YES
YES
Check short of
P9701, P9702 line
Check the
DC V of C981, C945 NO
Check short of P9702 line
If DC V is 6.1V
YES
Check the
DC V of C950,C951 NO
Check short of P9701 line
If DC V is in
34V
YES
OK
3-1
2. P-SENS 3. VKK PART CHECK
P-SENS VKK CHECK
YES YES
Check Check
the pin6 of P9702 NO Check power circuit the pin3 of P9702 NO Check power circuit
if DC V is over troubleshooting if DC V is over troubleshooting
5.6V -28V
YES YES
OK OK
4. MICOM PART CHECK I
MICOM PART
CHECK I
YES
Check P-SENS NO Refer to SMPS
(P7904_pin6) troubleshooting
YES
Check both Check
NO Check the
end voltage of NO NO Replace IC101
If input voltage of periphery of IC101
IC101 IC101 is over (KIA7042)
(KIA7042)
(KIA7042) 5V
YES YES
Check voltage of Check if IC101 of out-

IC1 00(LC87Fxxx) pin4 put voltage is over 4.3V
YES YES
OK OK
3-2
5. MICOM PART CHECK II
MICOM PART CHECK II
YES
Check P-SENS NO Refer to SMPS
(P7904_pin6) troubleshooting
YES
Check both NO Check NO
end voltage of D101 If output of Replace D101
D101 is 5V
YES
Check If IC103_pin8 and YES
IC100_pin14,40,55,89 are 5V
YES
Check D101
X101:32.768KHz
X100:9.8304MHz
Check the operation
YES YES
OK OK
6. IC103(S24CS16A01) PART CHECK
CHECK IC100
PIN93,94
YES
pin93:DATA NO NO Refer to MICOM
Check MICOM
pin94:CLK voltage 5V troubleshooting
YES
YES
NO
Check MICOM Replace MICOM
YES
OK OK
3-3
7. FLD DISPLAY CHECK
FLD DISPLAY CHECK
YES
Check
CN104 pin1, 2, 3 voltage NO Refer to SMPS troubleshooting
input
YES
Check if both end voltage of
F1,F2 are over 3.4V
VKK : over 26V
YES
Check
CN304 connection
and power pin24:FL+26, NO
pin23:FL-22, Check CN304 connection
pin22:VKK over 26V,
pin19:+5.6V YES
Check each pin voltage
YES YES
OK
Check
IC501(ET6315) voltage NO I f voltage is not 5V,
pin30 VKK:-26V check input and output of L502
pin13, 43:+5V YES
NO
Check IC501 Replace IC501
YES
YES
Check OK
IC102 --> IC501
data communication NO
3pin --> 9pin STB IC102 : pin2,3,4
2pin --> 7pin DATA check data Input
4pin --> 8pin CLK YES
Pin2 data out
check data input
YES
YES
FLD light on? NO
YES YES
OK OK
3-4
8. PWM MODULATION PART CHECK
PWM MODULATION
PART CHECK
YES
NO
check P7905 pin9,10 Refer to SMPS
3.3V troubleshooting
YES
Check IC604(PS9830)
VDD pin voltage (3,10,22,29, NO Check X601 NO
12.288MHz Replace X601
39,47,56,65,72,87,94)
check X601 pin2 :3.3V
YES YES
Check OK
X601 12.288MHz
operation
YES
Check line
check IC604 resistor output NO
SDA:R671,SCL:R670 Replace R671,R670,R665
pin86 CLK input
RST:R665
YES YES
Check
IC100(LC87Fxx) OK
pin34:PWM REST NO
pin86: PWM_DSP_DAT
pin87: PWM_DSP_CLK
Check P7403 NO
output DVD assy communication Refer to DVD troubleshooting
YES
YES
Check
IC604(PS9830) Check
NO NO Check each line
pin 23,24,25,26 IC604(PS9830) DATA
DATA input, resistor output
input
PWM wave
YES
YES
OK
Check PWM
modulator output
FL:pin75(+),74(-) NO Check NO Replace IC604
FD:pin71(+),70(-) IC604(PS9830)
check other
output
YES YES
OK OK
3-5
9. POWER AMP PART CHECK
POWER AMP PART CHECK
YES
P7905 pin3:+12V NO
Refer to SMPS troubleshooting
pin13,14,15:34V
YES
Check each IC700
pin27,26,32,35,40,41 input voltage
YES
Check each input NO
IC700 pin22,23,44:+12V Check each line resistor output voltage
YES
Check PWM modulator input
each pin6,8,16,18
YES
POWER output IC700 pin28,31,36,39
YES
Check output NO
Replace the coil
line coil
YES
OK
3-6
10. AUX FUNCTION PART CHECK
FUNCTION CHECK
YES
Each function
(tuner/tape/portable)
output to IC200(BU4052)
input : L/R_CH
YES
Check Check
IC200 (BU4052) NO IC200 (BU4052) NO Check P7905 connection
pin3,13 each function pin7:-12V after replace IC200
output pin16:+12V
YES YES
Each function
output line check
Check
Check IC801 NO IC801 (MC4580)
(MC4580) pin4:-12V
pin1,7 output pin8:+12V
YES YES
Check P7501 Refer to SMPS
pin6(L-CH), pin8(D-CH) troubleshooting
YES
Check
NO
IC201 (AK5358)
Check P201 connection
pin1,2 input
YES
Check
NO Check IC201 NO
IC201 (AK5358) Check CN202 pin4,5:+5V
pin6:+12V
pin9 data pin11,12: +3.3V
pin7:+3.3V
output
YES YES
Check IC501(ES8390) Check IC201
pin55 input data pin13:RST, pin11:MCLK,
pin9:DATA
YES
Check IC501(ES8390) YES
output data
YES
OK
3-7
11. TUNER/TAPE/PORTABLE FUNCTION PART CHECK
TAPE PLAY PART

CHECK
YES
Check IC201 NO
(HA12237)_pin16 Refer to SMPS troubleshooting
12V input
YES
Check
NO Check A/B NO Replace head wire and
IC201_ pin5,26
DECK head input tape DECK mechanism
output signal
YES
YES Check A DECK head input
IC201_pin32, 39 and B DECK
head input IC201_pin34, 37
YES
NO
YES
OK
Check
NO
IC201 pin14 Check IC202_pin10 "HIGH"
mute operation
YES
NO
YES YES
OK OK
3-8
12. TAPE PLAY PART CHECK
TAPE REC PART

CHECK
YES
Check NO Refer to PWM modulation
IC604(PS9830)
_pin49, 52 PWM troubleshooting
output
YES
Check IC201_pin7, 24
record input
YES
Check IC201_ NO Check IC100_ NO
Replace IC201
pin10, 21 output pin23 "HIGH"
YES YES
OK
Check L203_pin2, 3 NO NO
Check Q205(D1304)_ Check IC202_pin4 "HIGH"
oscillation
base "HIGH"
YES YES YES
Check P2203_pin5, 3 input OK Replace IC202
and pin8 erase input
YES
OK
3-9
DVD ELECTRICAL TROUBLESHOOTING GUIDE

1. POWER PART CHECK GUIDE
POWER ON POWER ON
YES YES
Does Does
Func AUX, FM Check an audio
DVD/CD NO
appear at FLD? 87.5 AM,USB micom or interface
appear at reconnect (CN201)
FLD?
YES YES
OK
Does it
NO appear DVD NO
error at FLD?
YES
Check connector NO
Reconnect it
(P400)
YES
Does no
Check the NO
disc or time
are appeared NO voltage of each pin Check connector
P7501
at FLD? on P201
YES YES
OK Check DVD MD
module
3-10
2. TEST & DEBUG FLOW
POWER ON
YES
Check connection lines
NO Flash memory NO between FLASH & ES8390 or
Show LOGO? operates properly? the FLASH access time
whether is suitable or not
YES YES
Check connection lines
SDRAM works NO between SDRAM (IC502) &
properly? ES8390 or the SDRAM is
damaged
YES
ES8390 VIDEO NO Check the related circuit of

outputs properly? ES8390 (IC501)
pin133,134,137,138,139,140
YES
Check AV cable connection
to TV set
Does tray
move inside when it is NO OPEN_SW&CLOSE_ NO Check the MD mecha
closed position? SW Signals on P406
are ok?
YES YES
OPEN / CLOSE NO Check the output signal of

signals on IC401 are ES8390 to IC401 for control
ok? OPEN /CLOSE
YES
Load+ & load- signals NO Check the tray control I/ O

on P406 are ok? pin on IC401
YES
Check the cable connection
A between DVD PCB and MD
(MECHA)
3-11
YES
Does the Motor Driver
SLED move to inner side NO NO
DRV_MMUTE pin 3 Check the MD
when it is at outer
position? High
YES YES
NO Check the related circuit of
SLED signal is OK? SLED
and Motor driver IC (IC401)
YES
Do not put in disc Check the cable connection
and tray close with MECHA
YES
Optical Proper
lens is moving NO NO
Focus outputs Check Focus connection on
for searching focus?
to motor driver? ES8390 and motor driver IC
YES YES
NO
Proper F+ & F- outputs? Check the motor driver (IC401)
YES
Check cable connection
B with pick-up head
3-12
YES
Laser turns on NO DVDLD or CDLD NO Check the laser power circuit

when reading between ES8390 and power
output properly?
disc?
transistor (Q405, Q406)
YES YES
Collector
voltage of power transistor NO Check the related circuit of
is ok? (Q405, Q406) laser power transistor
YES

between P4 00 and pick-up head
NO
Put disc in tray Laser off
YES
NO Proper SPINDLE NO
Does SPINDLE
rotate? signal on ES8390 Check the SPINDLE related
circuit on ES8390
YES YES
NO Check the SPINDLE control of
SPIN+ & SPIN- output
properly? motor driver (IC401)
YES
Check the cable connection
C between P400 and MD
3-13
YES
NO Proper signal on NO Check the connections between

Focus on ok?
A,B,C,D from MD? PDM 0 1 and pick-up head
YES YES
NO Check the related circuit of
Proper FOD signal on
IC401? ES8390 FOCUS signal
YES
between P400 and MD
NO NO
Proper TRD signal on Check the related circuit
Tracking ok?
IC401? between IC401 and ES8390
YES YES
NO Check the tracking control
T+ & T- output
properly? on motor driver (IC401)
YES
Check cable connection on
pick-up head
NO
Disc play? Check RF signal waveform
YES
3-14
YES
All Audio
outputs are ok NO NO Check the connections
signal data on
during playing between ES8390 and CN201
ES8390 is ok?
disk?
YES YES
Check the MAIN PCB
For example composite video,
NO Picture
signal data on NO Check the video mute TR
TEST END
ES8390 is ok? (Q507), ES8390 video signal
data
3-15
3. USB PART
TURN ON USB
YES
Check "Searching" or NO Check the POWER supply circuit
"USB" Display (Check P201)
YES YES
Check the HRST # signal
YES
Check the USB and DVD part
NO Check the USB part supply
Check Reading OK
(CN205)
YES YES
Check the USB data line (CN205)
YES
Check the ES8390
OK
(Check DATA LINE pin98_USB_NO, 99_PO)
3-16
WAVEFORMS OF MAJOR CHECK POINT

1. WHEN POWER ON, RESET & DATA ETC WAVEFORM
SPI DI
1 IC501 pin 72
SPI DO
2
IC501 pin 46
IC501 pin 47
TX
3
LCS3# (FLASH)
IC503 pin 1
4
HRST#
5V
D-
5 IC501 pin 91
D+
6 IC501 pin 90
3-17
2. OPEN/CLOSE WAVEFORM AT POWER ON
open
7 IC401 pin 11
UP-sw IC501 pin 63
DOWN-sw
9
IC501 pin 59
close
IC401 pin 10
10
3. STARTING ACTION WAVEFORM IN MD DEVICE
Driver STBY
SLEGN
SL+
IC401 pin 18
11
SL-
IC401 pin 17
12
4. FOCUS WAVEFORM (AT CD)
F+
IC401 pin 3
13
F-
IC401 pin 4
14
3-18
5. FOCUS WAVEFORM (AT DVD)
Q405(DVD_LD)
Q405
15
Q406(CD_LD)
Q406
16
6. AT POWER ON , SPINDLE SIGNAL AT MD DECK

Sclavijad
17 IC401 pin 21
Sclavija+
18 IC401 pin 15
Sclavija-
19 IC401 pin 16
7. TRACKING SIGNAL
Tro
IC401 pin 7
20
Tr-
P400 pin 16
21
Tr+
P400 pin 17
22
3-19
8. RF WAVEFORM
9. DISK TYPE JUGEMENT WAVEFORM

F+
23 P400 pin 18
24 FDO
IC401 pin 6
25
SVRRF
IC401 pin 23
DVD
F+
P400 pin 18
26
FDO
27 IC401 pin 6
SVRRF
28 IC401 pin 23
CD
3-20
WIRING DIAGRAM
B
C
P K P
3 C M L
1 E
D I
S O
V
N /
P E A B
P 8 L H S
6 B C U
U E
P
3
O M
D
P
0
1
P P
6 3
1
D P
M 1
1
R P B
E B B 6
G P C 3 C
N C 8 P P
A P 1 T
H D N
I N
C P V A O
3 D M R
D 2 F
V
D
3
P P
5 2
1
P
P 4
5 P
1 8
B
S C
P P
M C
I
S
M
3-21
2. DVD BLOCK DIAGRAM
M
S
I
N N
A M O M
H
C P
U
/ C O I
C F W
/ M I
F
/ E F
R
E P ± B I P W /
I
M E S M O
L U P
K ± D
T
, N
I
C ± P
E , S
F ,
D ± ±
D D
E A
L O
S L ]
R E )
# 3
, V
1 T
S
0
[ 8
.
O I 1 A 3
T V I
R
C 0
9 M
T
A V G
O R P
, D 3
D
M D I (
O A
, . E
V
D
D
I , K 3 R
R D
, C V
V G B
, 3 V V
, N
K
L K
.
3 5 2
1
D I
F I C K N C
, C
R
, D R C B E R
E D S L
, M V
F , 2 S E A
R Y U C
, D T
E O O L T B ,
V C D L S / P
D
, D
/ D
, D V
C L
,
1 C S
/ / E T
L S B
S
D N U D _ U
, C D O
B E C N P
I
A C D
L P O P M
O F S A
M
O
R SCI,SDA
P
E )
)
E N
G
N
I
I
P
P
M 6
6
E
DSCK#,CKE,CS0#,RAS0#
A 7
7
DMA[0..11],DB[0..15]
1
1
(
R (
D
S P 0
0
9
9
3
3
M
8
8 )
S
S T
S
I H S
E C
I F N
P S E / O
SPI_CS,CLK,DI,KO
S A M I R
L
F Z
H F
(
M
7
2
K A
C T
A
B
, D
,
K K
L C
C R e
M L t
i ,
s , B
/ R
o
p / b /
G r
m
Y P P
o
C
A
8
5
3
5
K
A
e t
t
i n
N R s e
I
- E E o n
x N P p o
u A p
U T m m
A T o o
C C
3-23
3-24
y r
l e
n t
o e S 1
. 3
e l
c
a o
m
t P 6 1
. T
l
p l v
M V 3
e a
R i t S E 0
. i
y
t
g
d
.
R 9
e a
f
a H 0
s
r i h
t 4 0
o w
f 0 2
l d 9
a r
c . e
i r 7 S
t
i e u
r b s
c
1
m a
e u e R
r n m
a t 4
s a
r C d
t
.
r - e 5
a p D o 8
p d e m
e
) i r y 3
f a a
i l
( c s P
d e e
e p g g R
d s t
a i
n
: a h
t l
E h i o r
u
T S
.
w V d
.
O 1 2
N

N Y S I Y
L H
S W
T E E
O L E N
D A T F G N
E . N . A A E
D N I
O D S H Q
H
H I
A O
T S
A S
E
U T
S C T
L
S A C E T I
E I
C C I T
T T N N
R F O A E
U L
A I
T C M D
U .
S N Y R E E D E
T E A I H V
C T O E T
N I
D M Y I
E A N
L F R L
N Y M A P E R P P
O S A U O M
P A R T N I D S
M E C O T I
O R G
A A I
I
E E
T C O R
C O E A N U
L F D H T N S T
A I
A C
I I T T N M A
C T I
U M
E R T R
E A C M E
E T
P O E O S I
S M R R L F L
E I
. H C F P R E E O
T C
I M E H C
R I P T I
U S S E ,
C E I
H F A
Y D O V
R
R
I H T F
I N T E
C T D W N S
A I
O N N L
L H
L
G
N I O T A
I A I N
I
S S
R E S W G
I
E D I . Y N
D L M N L R
N A R I
O N O
E O
U N P T E
I
, G A D H
T E T
I I U R
S
C
S R O O
A I
N
S O P L
A E H R P
T
H H I O E E
E C T W R S
C
O
C
I S D D E H M
T I L E R B T
O H U R E D
N T O E E L O
H T U T
Y G
T S L N O
N S R
I
E C
F A P
O
I H A
S L
A I E
C O S I
C
S V
R N E T T
T E A D
E H N N
E
N S T I E
F T N I
D
A S I L
T N M D O
R E U O M P S
O H C M
R E O M E
P 6
P W
M
I
I O
R Y
C B F C T
2
-
3
K
J
5
I 2
-
3
H
G
l
a
c
i
t
i
r r
c o F
e e
r r
a i
f
d f
e o
d k
a s .
h i
s r k
o c
r t
e t o
a c h
s
t e l
a s
g h p i
a
n t e i
i c
n r
s r t
r t
r t c
M
a a h e
i E
l
W P w e
A
R
) ) ) )
E E E E
T T T T
G
O O O O
N N N N
A
I . D
d
n
S D
u
o
r
T
I
g
. s
d i
n s
u s
U
a
o h
r
M
g c
C
C C
A D
A I
s s
R
e e
t t
o o
n n
C
R C
e e
d l
l d
o o
b b
G ) m m

y y
S S
A R ) )
I E
S S
E E
T T
D W
O O
N N B
O
T
I P
(
U S
C P
M
A
R
I S
.
C 1 2
1
1
1
0
1 9 8 7 6 5 4 3 2 1
T
S
R
Q
P
O
9
N
4
1
M
8 L
6 3 8
5 2
-
3
2
K
J
7
2
I
3
-
H
G
F
M
R
O
F
E
V
A
W E
D
M
A
R
G
A
I
C
D
T
I
U
C B
R
I
C
G
E A
P
M
. 2 1 0 9 8 7 6 5 4 3 2 1
1 1 1
2
T
S
R
Q
7 1 2

1 1 1
P
8
1
8 5
2 2 O
9
1
N
M
L
0
3
-
3
K
4 0
1 1
J
3
1
9
0 I 2
-
2 7 3
4 7
2 2
H
3
2
6
2
2
2 G
1
2
6
1
F
M
R
O
F
E
V
A
5 W
1 E
D
A
M
R
G
A
I C
D
T
I
U
C
R
I
B
C
O
V
R A
E
S
.
3 2
1
1
1
0
1 9 8 7 6 5 4 3 2 1
T
S
R
Q
P
O
N
M
L
2
3
-
3
K
J
1
3
I
3
-
H
G
F
E
D
M
A
R C
G
A
I
D
T
I B
U
C
R
I
C A
O
/
I
. 2 1 0 9 8 7 6 5 4 3 2 1
1 1 1
4
T
S
R
Q
P
O
N
M
L
4
3
-
3
K
J
3
I 3
-
3
H
G
F
M
A
R
G E
A
I
D
T
I
U D
C
R
I
C
E
C C
A
F
R
E
T B
N
I
+
M
O
C
I
A
M
.
5 2
1
1
1
0
1 9 8 7 6 5 4 3 2 1
T
S
R
Q
P
O
N
M
L
6
3
-
3
K
J
5
3
I
3
-
H
G
F
E
D
M
A
R
G C
A
I
D
T
I
U B
C
R
I
C
M A
W
P
. 2 1 0 9 8 7 6 5 4 3 2 1
1 1 1
6
T
S
R
Q
P
O
N
M
L
8
3
-
3
K
J
7
I 3
-
3
H
G
F
E
D
M
A
R
G C
A
I
D
T
I
U B
C
R
I
C
P A
M
A
.
7 2
1
1
1
0
1 9 8 7 6 5 4 3 2 1
T
S
R
Q
P
O
N
M
L
0
4
-
3
K
J
9
3
I
3
-
H
G
F
E
D
M
A
R
G
A
I
C
D
T
I
U
C B
R
I
C
K
C A
E
D
. 2 1 0 9 8 7 6 5 4 3 2 1
1 1 1
8
T
S
R
Q
P
O
N
M
L
2
4
-
3
K
J
1
I 4
-
3
H
G
F
E
D
A
M
R
G
A
I C
D
T
I
U
C B
R
I
C
T
N
O A
R
F
. 2 1 0 9 8 7 6 5 4 3 2 1
9 1 1 1
T
S
R
Q
P
O
N
M
L
4
4
-
3
K
J
3
4
I
3
-
H
G
F
M
A E
R
G
A
I
D D
T
I
U
C
R
I
C
C
E
M
U
L B
O
V
&
B
S A
U
.
0
2
1
1
1
0
1 9 8 7 6 5 4 3 2 1
1
T
S
R
Q
P
O
N
M
L
6
4
-
3
K
J
5
I 4
-
3
H
G
F
E
D
M
A
R
G C
A
I
D
T
I
U B
C
R
I
C
C
I A
M
.
1 2 1 0 9 8 7 6 5 4 3 2 1
1 1 1 1
0
5
-
3
9
4
-
3
)
V
(
e 1 1 1 9 7
d 8
o 0
. 0 . 1
. 0 . 4
. 0 4
.
M 0 0 0 0 3 3
E
E
.
O
N
N
I
2 3 4 5 6 7 8
P

)
V
(
e 1 1 1 8 6 4 2 8 2 6 9 3 9 9 5 6 6 8 1 8 3 9 8 2 2 2 8 5 2 1 3 8 9 7 1 6 8 9 7 5 1 1 1 y 6 5 4 1 3 1 4 1 1
d 7 3
. 2
o . 0 9 . 3
. 7 . 8 . 9
. 0 9 . 3
. 0 . 0 3 . 2
. 0 . 0 . 0
. 0 . 5
. 5
. . 3 . 0 . 3
. 5
. 7 . 3
. 6
. 0 0 . 0 . 3
. 4
. 0 . 0 0 . 8 . 3
. 8
. 7 . 0 . 7 . 6 . 3
. 8 . 9 . 0 . 1
. 0 . r 1 . . 0
. 6 . 5
. 6 . . 4
. 0 .
M 0 0 0 3 0 0 0 3 0 3 3 0 0 0 0 0 0 1 3 0 1 1 1 1 2 0 0 3 1 0 0 0 3 0 0 0 0 0 3 0 0 0 1 0 o 3 1 3 0 0 2 3 3 0
B m M
e O
P M R
H P
S E
A E
L 4
F 0
. 3 5
O 0 C
I
N 5
N 5 6 7 8 9 0
I 2 1
1 1 1 3 1 5 6
4 1 1 7
1 8
1 9
1 0 1 2 2
2 2 3 2 5 6
4 2 2 7
2 8
2 9
2 0 1 3
3 3 2 3 3 5 6
4 3 3 7
3 8
3 9
3 0 1 4
4 4 2 4 5 6
3 4 4 4 7
4 8
4 9
4 0 1 5
5 5 2 5
3 5 C 1 2 3 4 5 6 7 8
4 I 1
P

) )
V
( V
(
e 3 3 8 3 7 9 8 2 2 6 6 5 9 9 3 9 d e 9 1 1 9 6 8 9 2 1 3 1 6 9 6 9 1
d 3 5 5 2 6 5 8 9 2 1 9 8 2 8 7 6
o 0 0 5 . 3 . 2
. 0 1 . 2
. 3
. 5
. 4
. 0 7 . 3
. 6
. 0 0 . 5
. 1 . 5
. 0
. 0
. 0
. 0
. o 1
. 1 . 1
. 0 . . 7 . 0 2
. 7 . 0
. 0 0 8 . 2
. 2
. 3
. 8 0 . 1
. . 7 . 4
. 0 0 1 . 0 2
. 1 . 2
. 5
. 3
. . 3 . 7
.
M 1 3 1 1 1 1 3 1 1 2 0 0 0 0 0 0 0 M ) 2 2 2 2 4 1 1 3 1 4 0 0 3 0 . 2 2 4 1 1 0 1 2 1 3 0 3 0
1 M
E E 1
E E 0
9
A
P R
I
( D
S
1 2
0 0
) 4 5
V
( C
I C
e . I
d 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 O D D
o 5 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 7 7 7 7 7 7 7 N 1 2 3 4 5 6 7 N 8 9 0 1 2 3 4 5 6 7 8 9 0 1 N 2 3 4 5 6 7 8 1 2 3 4
M 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I
N 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2
G G
E P
E

2
5
-
3
1
5
3
-
S
M )
A W
G E
I
R V
A
I P
O
D T
D (
R M
A
A R
O G
B A
I
D
T
I D
U R
C A
O
R
I B
.
C C
.
D P
E N
T I
A
N
I M
.
R 1
-
P 1
4
5
-
3
3
5
-
3
)
W
E
I
V
M
O
T
T
O
B
(
M
A
R
G
A
I
D
D
R
A
O
B
.
C
.
P
N
I
A
M
.
2
-
1
6
5
-
3
5
5
3
-
)
W
E
I
V
P
O
T
(
M
A
R
G
A
I
D
D
R
A
O
B
.
C
.
P
D
V
D
.
1
-
2
8
5
-
3
7
5
-
3
)
W
E
I
V
M
O
T
T
O
B
(
M
A
G
R
A
I
D
D
R
A
O
B
.
C
.
P
D
V
D
.
2
-
2
.
k
h c
t o
i h
W s
l l
a a
c c
t i
i
i r
r t
c c
e
e l
r e
a r
d o
e
e r
i
d f
a
h
s f
o
e k
s
r i
a r
t t
o
g a t
n
i h
t c
n s e
r t
a a p
r s
W P r e
:
E
T
O
N 0
6
-
3
9
5
3
-
M
A
R
G
A
I
D
D
R
A
O
B
.
C
.
P
S
P
M
S
.
3
M
A
R
G
A
I
D M
A
D R
R G
A A
O I
B D
. D
C
. R
P A
E O
N B
.
O C
H .
P
D
P K
A C
E A
H J 2
. . 6
5 7 -
3
1
6
-
3
M
A
R M
G
A A
R
I
D G
D A
I
R D
A D
O R
B A
. O
C
. B
P .
T C
.
N P
O C
R I
F M
. .
4
6
4
6
-
3
3
6
3
-
SECTION 4. REPLACEMENT PARTS LIST

NOTES) If you want to purchase NOTES) Warning
Flash memory, you must order NOTES) Parts that are shaded are critical
"IC100A, IC803A" NOTES) With respect to risk of fire or
NOTES) electricial shock.
/DXCN ( Latin America)

MODEL: X-RSM400DV /LXCN ( ASEAN)
/DXCNRI ( Middle East)
. ELECTRICAL SECTION
A41 PCB Assembly, DVD
A41 EBR64618202 PCB Assembly MDT404 DVD TTL pioneer Singapo LXCN
A41 EBR64618201 PCB Assembly MDT404 DVD TTL pioneer DXCN, DXCNRI
IC503A SAA34922202 S/W,System Program MDT404 MDT404/ASIA/ES8390 - WO LXCN
IC503A SAA34922201 S/W,System Program MDT404 MDT404/EU/ES8390 - WORL DXCN, DXCNRI
CN201 6630XE00118 Connector,FFC/FPC/PIC 04-6232-018-010-000 18P 1.00MM
CN205 561-716F Connector,Wafer GIL-G-06P-S3L2-E 6P 2.50MM 1R
IC201 EAN30955301 IC,A/D Converter AK5358 2.7 TO 5.5 24.576MHZ 0B
IC401 EAN35154201 IC,Motor Driver IP9011L-TF 4.3to13.2v 4v 2.3W
IC501 EAN41510001 IC,Video Processors ES8390SCC 2VTO5.5V,0VTO0V,0VTO
IC502 EAN56306901 IC,SDRAM V54C3128164VBI6 128MBIT 8M X 1
IC508 0ISTLPH025A IC,CMOS 74LVC00APW 1.2TO3.6V 0.01mA NA

IC509 EAN34180901 IC,LDO Voltage Regulator LM1117S-ADJ 15V ADJ 1W SOT223
JK201 6612J00015J Jack,RCA RCA-405A-18 14.0MM 2RX2C ANGLE
P400 6630XE00123 Connector,FFC/FPC/PIC 04-6232-023-010-000 23P 1.00MM
P409 6630XE00105 Connector,FFC/FPC/PIC JE500-B1.0-T05 5P 1.00MM FFC S
Q401 0TRRH80042A FET 2SK3018-T106 N-CHANNEL MOSFET
Q402 0TRRH80042A FET 2SK3018-T106 N-CHANNEL MOSFET
Q403 0TR387509AC TR,Bipolar KTC3875S-GR(ALG) NPN 5V 60V 50
Q405 0TRAU80008A TR,Bipolar 2SA1980SY PNP -5V -50V -50V -0
Q406 0TRAU80008A TR,Bipolar 2SA1980SY PNP -5V -50V -50V -0
Q500 0TR130409BA TR,Bipolar KTD1304S NPN 12V 25V 20V 300MA
Q506 0TR129809BB TR,Bipolar KTA1298Y PNP -5V -35V -30V -0.
X501 EAW32919201 Crystal HC49SMD 27MHZ 27MHZ 20PPM 15pF
A43 PCB Assembly, Front
A43 EBR64580201 PCB Assembly,Front MDT404 FRONT TTL ASSY pioneer DXCN
A43 EBR64580202 PCB Assembly,Front MDT404 FRONT TTL ASSY pioneer LXCN, DXCNRI
CABLE1 EAD43284604 Cable,FFC AT12536200C04 200MM 1.25MM 36P
CN302 EAD39212204 Harness,Single SAN-10A To TJC2511-10Y_L=200MM
CN305 EAD54699902 Harness,Single 4P-100MM (Tape) GIL-S-04 9073-
CN307 EAD48775203 Harness,Single HS-LG09-003(MDT353) A2507H02-0
CN308 EAD42360604 Harness,Single 3P-120MM(Tape) GIL-S-04 9073-S
IC301 EAN59815801 IC,Display Driver MC3501_VFD Driver 5.5 0.4 5MW
IC361 0IPMGKE018A IC,LDO Voltage Regulator KIA78R05PI CU 6TO12V 5V 1.5W T
IC380 EAN57059401 IC,PRE Amplifier S4308 4.5V TO 14V 0.01V 0.1% 2
JK350 6612R-A002A Jack,Phone PPJ35G 1P 3P STRAIGHT TR 3.6MM
JK361 EAG43134801 Connector,USB U250FD004S118XY A 1P 2.50/2.00
JK380 572-559F Jack,Phone HTJ-064-04B 1P 3P ANGLE TR 6.4
JK381 572-559F Jack,Phone HTJ-064-04B 1P 3P ANGLE TR 6.4
LD301 EAV35747602 LED,DIP BL-BUB3V4V-4-AV-TBS20.9A 65+/- DXCN

LD301 0DLBE0175AA LED,DIP BZ-CB53K1A-1-TBS20.9A ROUND 4. LXCN, DXCNRI
PN301 561-7078 Connector,FFC/FPC/PIC 12517HS-36A00 36P 1.25MM FFC/F
PN303 561-707P Connector,FFC/FPC/PIC 52492-1620 16P 1.25MM FFC/FPC

PN304 561-712C Connector,Wafer GIL-S-03P-S2L2-EF 3P 2.00MM 1R
PN306 561-707P Connector,FFC/FPC/PIC 52492-1620 16P 1.25MM FFC/FPC
PN309 561-711D Connector,Wafer GIL-S-04P-S2T2-EF 4P 2.00MM 1R
Q301 0TR102009AA TR,Bipolar KRC102S-T1 NPN 30V -10V 50V 10
SW301 EBF40098801 Switch,Tact SKRGAED010 1C1P 12VDC 0.05A VE


VR301 6110E00019E Switch,Encoder EVEKD2F3024M ENCODER 5VDC 0.01
VR380 6110E00018A Switch,Encoder EVE LC1 F25 24M INCREMENTAL 5V
A46 Option Code Assembly, MAIN
A46 EBR64582101 Option Code Assembly F5 00 24 CD 00 69 83 20 60 00 DXCN
A46 EBR64582102 Option Code Assembly F5 00 A4 BD 00 69 83 20 60 00 LXCN
A46 EBR64582103 Option Code Assembly F5 00 A4 AD 00 09 83 20 60 00 DXCNRI
IC100A SAA34922301 S/W,System Program MDT404 A_MICOM - WORLD WIDE A_
IC101 0IKE704200J IC,Voltage Detector KIA7042AF -0.3TO15V 4.2V 500MW
IC102 0IKE702700D IC,Voltage Detector KIA7027AF -0.3TO15V 2.7V 500MW
IC103 EAN57037601 IC,EEPROM M24C16-RMN6TP 16KBIT 2KX8BIT 1
IC200 0IRH405200C IC,CMOS BU4052BCFV 3TO18V 0.015mA MULT
IC201 0IPRP00006A IC,Sound/Audio Processor HA12237F 6.5VTO15V 625MW QFP T
IC604 EAN59324101 IC,PWM Controller PS9831 2.97V TO 3.63V ADJ 2.2W
IC700 EAN41746102 IC,Power Amplifier TAS5352ADDV Pre attached pad 1
IC701 EAN41746102 IC,Power Amplifier TAS5352ADDV Pre attached pad 1
IC801 0ILNRUC001A IC,OP Amplifier MC4580 SOP +-2TO+-18V 15V 0.00
IC802 0ILNRUC001A IC,OP Amplifier MC4580 SOP +-2TO+-18V 15V 0.00
JK701 6640000071A Connector,Terminal Block PTB-610A-00-01 6P 13.0MM ANGLE
JK800 6612J00018G Jack,RCA RCA-305A-01-07 LM-K7960 15MM
P2201 6630XF00413 Connector,FFC/FPC/PIC 12511HS-13 13P 1.25MM FFC STRA
P2202 561-715C Connector,Wafer GIL-G-03P-S3T2-E 3P 2.50MM 1R
P2203 561-715H Connector,Wafer GIL-G-08P-S3T2-E 8P 2.50MM 1R
P7302 6630XF00436 Connector,FFC/FPC/PIC 12511HS-36SS-K 36P 1.25MM FFC/

P7501 561-711L Connector,Wafer GIL-S-12P-S2T2-EF 12P 2.00MM 1
P7708 561-661B Connector,Wafer 99990986 2P 2.50MM 1R STRAIGHT
P7905 561-7150 Connector,Wafer GIL-G-15P-S3T2-E 15P 2.50MM 1R
PN102 561-715J Connector,Wafer GIL-G-10P-S3T2-E 10P 2.54MM 1R
Q201 0TFPH80002A FET 2N7002 N-CHANNEL DMOSFET 60V +
Q204 0TR320509AB Transistor Assembly KTC3205-Y(KTC2236A) KTC3205-Y(
Q206 0TR127309AA TR,Bipolar KTA1273 PNP -5V -30V -30V -2A

Q212 0TR102009AC TR,Bipolar KRA102S PNP -30V -10V -50V -0.
Q213 0TR103009AA TR,Bipolar KRC103S-T1 NPN 40V 300MV 50V 1
Q800 0TR129809BB TR,Bipolar KTA1298Y PNP -5V -35V -30V -0.
Q802 0TR150409AC TR,Bipolar KTA1504S-GR PNP -5V -50V -50V

TUN800 EBL57006801 Tuner,Analog KST-MW004MV0-S60W AM/FM 520KHZ
X100 EAW32918901 Crystal HC49SMD 9.8304M 9.8304MHZ 20PP
X101 6212AB2327X Crystal MC-146 32.768KHZ 20PPM 12.5pF
X601 EAW32919901 Crystal HC49SMD 12.288M 12.288MHZ 20PP
A47 PCB Assembly, Power
A47 EBR40198721 PCB Assembly,Power MDT404 HZ(450V) SMPS TTL ASSY
CABLE7 EAD42218201 Harness,Single 15P-140MM (XD123) GIL-G GIL-G
CABLE8 EAD60517002 Harness,Single HS-LG08-006 A2507H02-08 A2507H
BD901 EAH42986602 Diode,Bridge RBU605M-B-C-V50 600V 1.1V 2UA
C902 EAE42617201 Capacitor,Ceramic,Radial CT7-Y10Y5U9E222MSEW 2200pF -20
C903 0CE1066K618 Capacitor,AL,Radial SMS5.0TP50VB10M 10uF 20% 50V 7
C906 EAE42617701 Capacitor,Ceramic,Radial CT7-Y7Y5U9E102MSEW 1000pF -20T

C907 0CQ1031Y519 Capacitor,Film,DIP 230S 2J 103 K 10nF 10% 630V MP
F901 0FS8001B51B Fuse,Time Delay FUSE 8000MA GLASS 250V 8A KS/J
IC901 0IPMGSK021A IC,HIC STR-X6759N 16.3TO19.9V 8.8TO10
IC902 0IPMG00042A IC,HIC STR-A6252(LFA2) 12.9TO15.7V 9T
IC942 0IPMGUC004B IC,LDO Voltage Regulator TL431K-T92-B MAX12V 3.3V 600MW
IC947 0IKE781200S IC,LDO Voltage Regulator KIA78R12PI-CU 13TO29V 12V 1.5W
IC949 0IPMGUC004B IC,LDO Voltage Regulator TL431K-T92-B MAX12V 3.3V 600MW
IC955 0IPMG78358B IC,LDO Voltage Regulator KIA278R35PI-U 4.2TO10V 3.5V 1.
IC957 0IPMGKE018A IC,LDO Voltage Regulator KIA78R05PI CU 6TO12V 5V 1.5W T
LF901 6200JB8009X Line Noise Filter LINE FILTER(WITH BASE) SAMWHA
LF902 6200JB8009X Line Noise Filter LINE FILTER(WITH BASE) SAMWHA
P9701 561-7150 Connector,Wafer GIL-G-15P-S3T2-E 15P 2.50MM 1R
P9900 561-292B Connector,Wafer GP390-03P-TS 3P 3.96MM 1R STRA
PC901 657-063A Sensor,Position LTV-817B 5V DIP BK 2P Photo Co

Q904 0TR320209AA Transistor Assembly KTC3202-Y (KTC1959) KTC3202-Y
Q951 0TR198009CA TR,Bipolar 2SA1980G PNP -5V -50V -50V -0.
T901 6170RNGW25B Transformer,Switching DD332W EER4249 220uH 10uH 0.4O
T902 EBJ40392102 Transformer,Switching EER2828 16pin 800uH_10Precent_
TH901 EBG43133901 Thermistor,NTC NTC 4D-15 4OHM +-15% 5V 6A 76K
VR901 EAF43134201 Varistor FNR-14K681T 680V 10% 250pF 14p
ZD960 0DZ270009BC Diode,Zener GDZJ2.7A(52mm tapping) 2.7V 2.
SECTION 5. DIAGNOSIS CONNECTION
When diagnosing Main Assembly or CD Total Assembly, perform the following

connection and style
Extension FFC: GGD1423

Connecting it between PCB
Assembly (DVD) and
Option Code Assembly
A26 Mechanism Assembly
5-1

Dokumen Pioneer-Rsm400

Uploaded by

Copyright:

Available Formats

Dokumen Pioneer-Rsm400

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dokumen Pioneer-Rsm400

Uploaded by

Copyright:

Available Formats

5/23/2018 Pioneer RSM400-slidepdf.

DVD MINI COMPONENT SYSTEM

X-RSM400DV LXCN AC 110 V to 240 V 3 &&&&######LE LE : ASEAN

X-RSM400DV DXCN AC 110 V to 240 V 4 &&&&######ME ME : LATIN AMERICA

X-RSM400DV DXCNRI AC 110 V to 240 V 2 &&&&######RB RB : MIDDLE EAST

For details, refer to "Important Check Points for good servicing".

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

LASER DIODE CHARACTERISTICS

For CD Wave Length: 789 nm

[Important Check Points for Good Servicing]

1 Use specified parts for repair.

Use genuine parts. Be sure to use important parts for safety.

2 Do not perform modifications without proper instructions.

3 Make sure the soldering of repaired locations is properly performed.

4 Make sure the screws are tightly fastened.

5 Make sure each connectors are correctly inserted.

9 There should be no spark traces or similar marks on the power plug.

3. Lubricants, Glues, and Replacement parts

5. Shipping mode and Shipping screws

SECTION 5. DIAGNOSIS CONNECTION ………………………...….…..…………….. 5-1

NOTES REGARDING COMPACT DISC PLAYER REPAIRS

2. Notes for repair

CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL OTHER

THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN AN EQUILATERAL TRIANGLE, IS

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE

When Option Code Assembly

Net Weight 5.8 kg

Cassette tape player

Speakers FRONT SPEAKER SUBWOOFER SPEAKER

Designs and specifications are subject to change without pior notice.

D 7 8

E 4 4 2 4

LOCA. NO PART NO. DESCRIPTION SPECIFICATION REMARKS

(2) PASSIVE SUBWOOFER

LOCA. NO PART NO. DESCRIPTION SPECIFICATION REMARKS

4. PACKING ACCESSORY SECTION

82 4 Antenna, Loop (AM)

90 0 Remote Controller 82 5 Antenna, T (FM)

811 RCA Cable, 1Pin(Black)

803WT Packing, Woofer Top

804W Bag, Woofer 804F Bag, Front Speaker

804 Bag, Main Set 804F Bag, Front Speaker

NOTES) If you want to purchase NOTES) Warning

/DXCN ( Latin America)

. PACKING & ACCESSORY SECTION

801 Manual Assembly, Owners AFN37125930 AFN37125932 AFN37125931

SECTION 3. ELECTRICAL PART

2. P-SENS 3. VKK PART CHECK

P-SENS VKK CHECK

4. MICOM PART CHECK I

Check voltage of Check if IC101 of out-

5. MICOM PART CHECK II

MICOM PART CHECK II

6. IC103(S24CS16A01) PART CHECK

7. FLD DISPLAY CHECK

FLD DISPLAY CHECK

8. PWM MODULATION PART CHECK

9. POWER AMP PART CHECK