Operation & Maintenance: Paver Finisher Dynapac SD2550C / SD2550CS

OPERATION & MAINTENANCE
Paver Finisher
Dynapac
SD2550C / SD2550CS
Typ 894 / 895
01-0516 4812313708
CN Keep for later use in document compartment
Valid for:
_________________ - _________________
_________________ - _________________
www.atlascopco.com
Table of contents
V Preface ................. .............................................................................. 1
1 General safety instructions ................................................................................ 2
1.1 Laws, guidelines, accident prevention regulations ....................................... 2
1.2 Warnings .......... ....................................................................................... ............. 2
1.3 Prohibitive symbols ............................................................................................ 4
1.4 Protective equipment ......................................................................................... 5
1.5 Environmental protection ................................................................................... 6
1.6 Fire prevention ................. .................................................................................. 6
1.7 Additional information ...... .................................................................................. 7
2 CE identification and Declaration of Conformity .......................................... 8
3 Guarantee conditions ............ ............................................................... ............. 8
4 Residual risks ............ .......................................................................... ............... 9
5 Sensibly predictable incorrect usage .............................................. ............. 10
A Correct use and application .......................................................... 1
B Vehicle description ......................................................................... 1

1 Application .............. ............................................................................... ............. 1
2 Description of assemblies and functions ........................................................ 2
2.1 Vehicle ................................................................................................................... 3
Construction ....................................................................................... ............. 3
3 Danger zones ......................................................................................................... 7
4 Safety devices ....................................................................................................... 8
5 Technical data, standard configuration ........................................... ............. 10
5.1 Dimensions (all dimensions in mm) ............................................................... 10
5.2 Allowed angle of rise and slope ............................ ................................ ......... 11
5.3 Permissible approach angle ............................................................................. 11
5.4 Weights SD2550C (all weights in t) ............................................................... 12
5.5 Weights SD2550CS (all weights in t) ................................................... ......... 12
5.6 Performance data SD2550C ............................................................................. 13
5.7 Performance data SD2550CS ............................................................ ............. 14
5.8 Travel drive/traction unit ................... .................................................... ........... 15
5.9 Engine SD2550C ................................................................................................. 15
5.10 Engine SD2550CS ................................................................................... ........... 15
5.11 Hydraulic system .................................................................................... ........... 15
5.12 Material compartment(hopper) ....................................................................... 16
5.13 Material transfer ............. ....................................................................... ........... 16
5.14 Material distribution SD2550C ............................................................... ......... 16
5.15 Material distribution SD2550CS ...................................................................... 16
5.16 Screed lifting device .......................................................................................... 17
5.17 Electrical system ................................................................................................. 17
5.18 Permissible temperature ranges ...................................................................... 17
1
6 Location of instruction labels and identification plates .................... ......... 18
6.1 Warning signs .................................................................................................... 20
6.2 Information signs ............................................................................................. 23
6.3 Instructive symbols, prohibitive symbols, warning symbols ................... 26

6.4 Danger symbols ................................................................................................. 27
6.5 Further warnings and operating instructions ............................................. 28
6.6 Identification label for the paver finisher (41) ............................................. 30
7 EN standards ...................................................................................................... 32
7.1 Continuous sound pressure SD2550C, Cummins QSB 6.7-C260 ............. 32
7.2 Operating conditions during measurement ................................................ 32
7.3 Measuring point configuration.............................................................. ......... 32
7.4 Continuous sound pressure SD2550CS, Cummins QSB 6.7-C260 ......... 33
7.5 Operating conditions during measurement ................................................ 33
7.6 Measuring point configuration ....................................................................... 33
7.7 Vibration acting on the entire body .............................................................. 34
7.8 Vibrations acting on hands and arms ............................................................ 34
C11 Transportation ................................................................................... 1

1 Safety regulations for transportation .............................................................. 1
2 Transportation on low-bed trailers ................................................................. 2
2.1 Preparations .......................................................................................................... 2
3 Securing the load ................................................................................................. 4
3.1 Prepare the low-bed trailer ................................................................... ............. 4
3.2 Driving onto the low-bed trailer .......................................................... ........... 5
3.3 Lashing equipment .............................................................................................. 6
3.4 Loading .................................................................................................... ............. 7
3.5 Preparing the machine .......... ............................................................... ............. 8
4 Securing the load ................................................................................... ............. 9
4.1 Securing at the sides ....... ................................................................................... 9
4.2 Securing at the front............................................................................... ............. 9
4.3 Securing at the rear - screed with side board ............................................. 10
4.4 Securing at the rear - screed without side board ....................................... 11
Step 1: fasten lashing straps ...................................................................... 11
Step 2: fasten lashing chains ........................................................ ............. 11
5 Control panel transport safeguard: ............................................................. 12
5.1 After transportation .......................................................................................... 13
6 Protective roof (o) .................................................................................. ........... 14
7 Transportation ................................................................................................... 15
7.1 Preparations ........................................................................................................ 15
7.2 Driving mode ........... ............................................................................... ........... 17
8 Loading by crane .............................................................................................. 18
9 Towing ................................................................................................................. 20
10 Safely parking the vehicle ................................................................................ 22
2
D11 Operation ........................................................................................... 1
1 Safety regulations ............................................................................... ............... 1
2 Controls .................................................................................................................. 2
2.1 Operating panel .................................................................................................. 2
2.2 Special functions ................................................................................................ 50
Reversible conveyor .................................................................................... 50
3 Remote control ................................................................................................... 53
D20 Operation ........................................................................................... 1

1 Operation of the input and disp lay terminal ................................................... 1
Button layout on the display .......................................................... ............... 1
Command symbols ........... ............................................................................. 2
Menu range ...................................................................................................... 2
1.1 Menu operation .................................................................................................... 3
Menu structure of the settin g and display options ................................... 5
Main menu ...................................................................................................... 6
Displays: ............................................................................................................ 6
Menu 01 -
diesel engine speed ........................................................................ ............... 8
Set-up menu 101 -
diesel engine speed ....................................................................................... 8
Menu 02 -
drive engine measured values ..................................................................... 9
Sub-menu 201 -
drive engine measured value display ........................................................ 9
Menu 03 -
paving distance ............................................................................................ 10
Sub-menu 301 -
displaying, resetting paving distance /
automatic steering unit ON/OFF, steering monitoring ......................... 10
Menu 04 -
external levelling .......................................................................................... 11
Setting menu 401 -
external levelling .......................................................................................... 11
Menu 05 -
paving thickness .......................................................................................... 12
Set-up menu 501 -
paving thickness
preselection .................................................................................................. 12
Menu 06 -
screed parameters .......................................................................... ............. 13
Setting menu 600 -
compacting element frequencies ............................................................. 14
Setting menu 601 -
delayed screed start .................................................................................... 14
Setting menu 602 -
screed type selection ................................................................................... 15
Setting menu 603 -
screed heater system .................................................................................. 15
Menu 07 -
conveyor / auger capacity .......................................................................... 16
3
Set-up menu 700 -
conveyor / auger capacity ........................................................................... 16
Menu 08 -
system information ....................................................................................... 17
Menu 09 -
service ............................................................................................................. 18
Menu 10 -
error memory ............................................................................................... 19
Query menu 111 -
error memory: ............................................................................................. 19
Error display .................................................................................... ............. 20
Menu 11 -
terminal settings ........................................................................................... 21
Setting menu 110 -
terminal settings .......................................................................................... 21
System menu -
Basic settings Display .................................................................................. 22
Menu 12 -
button function test ........................................................................ ........... 23
Test menu 120 -
button function test ..................................................................................... 23
Menu 13 -
camera display (camera 2) .. ....................................................................... 24
Menu 13b -
camera display (camera 1) .......................................................................... 24
2 Terminal error messages ...... ............................................................ ........... 25
2.1 Drive engine error codes .................................................................................. 44
2.2 Error codes ........................................................................................... ........... 46
D30 Operation ............................................................................................. 1

1 Operating elements on the paver finisher .... ................................................ 1
1.1 Control elements on the operator's control station ..................................... 1
Protective roof (o) .......... ................................................................................ 1
Protective cabin (o) ........... ............................................................................. 2
Windscreen wiper ............... ........................................................................... 2
Control panel, rigid ......................................................................................... 3
Operating panel, moveable ........................................................................... 3
Control platform, moveable (o) .................................................................. 4
Operating panel, moveable ........................................................... ............... 5
Operating panel, swivelling (o) .................................................................. 5
Control platform lock (o) ................................................................................ 5
.Emergency actuation control
platform, movable .......................................................................................... 6
Seat console, swivelling (o) ........................................................................... 7
Seat console storage compartment ................ ........................................... 7
Driver's seat, type I ....... ................................................................................ 8
Driver's seat, type II ...................................................................................... 9
Fuse box ......................................................................................................... 10
Batteries ........................................................................................................... 11
Main battery switch ......................................................................................11
Hopper transport safeguard ..................................................................... 12
Screed lock, mechanical (o) ........................................................................ 12
4
Screed lock, hydraulic (o) ...................................................................... ......... 13
Paving thickness indicator ............................................................................... 14
Auger lighting (o) ............................................................................................... 15
Engine compartment lighting (o) .................................................................. 15
Xenon working light (o) .................................................................................... 16
LED working light (o) ........................................................................................ 16
500 watt spotlight (o) ........................................................................................ 17
Camera (o) .......... ................................................................................................ 17
Auger height adjustmentratchet (o) .............................................................. 18
Auger height indicators ....................................................................... ........... 18
Sensor rod / sensor rod extension ................................................................ 19
Manual separator fluid spray(o) ............ ........................................................ 21
Separator fluid spraying system(o) ............................................................... 22
Conveyor limit switches -PLC version .......................................................... 23
Conveyor limit switches -conventional version ............................. ........... 24
Ultrasonic auger limit switches (left and right) - PLC version .................. 25
Ultrasonic auger limit switches (left and right) - conventional version . 26
24 volt / 12 volt sockets (o) .................................................................... ......... 27
Pressure control valve for screed charging/relieving ................................ 28
Pressure control valve for paving stop with relieving ................................ 28
Manometer for screed charging/relieving ................................................. 28
Central lubrication system (o) ........................................................................ 29
Lane clearer (o) .................................................................................................. 30
Screed eccentric adjustment ............................................................. ............. 31
Push roller crossbar,
adjustable ............... .......................................................................................... 32
hydraulically extendable (o) ........................................................................... 33
Push roller damping,
hydraulic (o) ........................................................................................................ 33
Storage box ........................................................................................................ 34
Fire extinguisher (o) .......................................................................................... 34
Rotary beacon (o) .............................................................................................. 35
Fuelling pump (o) ............................................................................................... 36
Power moon (o) ......... ........................................................................... ........... 37
D41 Operation ................................................................................................ 1

1 Preparing for operation .......................................................................................... 1
Required devices and aids ................................................................................ 1
Before starting work
(in the morning or when starting paving) ..................................................... 2
Check list for the vehicle operator ................................................... ............... 2
.............. ................................................................................................. ............... 4
1.1 Starting the paver finisher......................................................................... ............. 5
Before starting the paver finisher ........ .............. ............... ............................... 5
"Normal" starting ............... ................................................................................. 5
External starting (starting aid) ......................................................................... 7
After starting ......................................................................................................... 9
Observe indicator lamps .................................................................................. 11
Engine coolant temperature check (79) ........................... ................. ......... 11
Battery charge indicator (83) ........................................................................... 11
Oil pressure indicator lamp for the diesel engine (86) .................... ......... 11
5
Oil pressure indicator lampfor the travel drive (87) .................. ............. 13
1.2 Preparation for transportation ......................................................................... 15
Driving and stopping the paver finisher ............................. ........................ 17
1.3 Preparations for paving .................................................................................... 18
Separator fluid ............................................................................................... 18
Screed heater system .................................................................................... 18
Direction marks .............................................................................................. 19
Loading/conveying material ......................................................... ............. 21
1.4 Starting for paving .............................................................................................. 23
1.5 Checks during paving ........... ........................................................................... 24
Paver function ............ ....................................................................... ........... 24
Quality of the layer ......................................................................................... 24
1.6 Paving with "screed control at paving stop" and
"screed charging/relieving" ............................................................................ 25
General ................. .......................................................................................... 25
Screed charging/relieving ........................................................................... 27
Screed control with paver finisher stop / in paving operation
(screed stop / paving stop / floating paving) ........................................... 27
Adjusting the pressure ................................................................................. 31
Setting pressure for screed control with paving stop + relieving:........ 31
1.7 Interrupting/terminating operation .............................................................. 33
During breaks (e.g. the material supply truck is late) .................. ........... 33
During longer breaks(e.g. lunch break) .................... .................... ........... 33
When work is finished ......... ......................................................................... 35
2 Malfunctions ....................................................................................................... 36
2.1 Problems during paving ................................................................................... 36
2.2 Malfunctions on the paver finisher or screed ............................................... 38
E11 Set-up and modification ................................................................ 1

1 Special notes on safety ...... ................................................................................ 1
2 Distribution auger ............................................................................................... 2
2.1 Height adjustment .............................................................................................. 2
Grain sizes up to 16 mm ................................................................. ............... 2
Grain sizes > 16 mm ........................................................................................ 2
2.2 Mechanical adjustment
with ratchet (o) ..................................................................................................... 3
2.3 Hydraulic adjustment (o) .................................................................................... 3
2.4 Height adjustment for large working widths / with brace ......................... 4
3 Auger extension ............... .................................................................................. 6
3.1 Mounting extension parts ................................................................................... 7
Mounting the material shaft and auger extension ................................. 7
Mounting the outer auger bearing ............................................... ............. 8
Mounting the auger end bearing ................................................................ 9
6
3.2 Auger extension chart ...................................................................................... 10
Auger upgrading, working width 3.14 m ................................................ 12
Auger upgrading, working width 3.78 m ................................................. 12
Auger upgrading, working width 7.62 m ......... ............................. ......... 16
Auger upgrading, working width 8.26 m ......... ....................................... 17
Auger upgrading, working width 8.90 m ......... ....................................... 18
Auger upgrading, working width 9.54 m ......... ............................. ......... 19
Auger upgrading, working width 10.18 m .............................................. 20
3.3 Mounting the auger brace ..... ......................................................................... 25
3.4 Aligning the auger ............................................................................................. 27
3.5 Material shaft, hinged ........................................................................................ 29
3.6 Hopper scraper ......... ........................................................................................ 30
4 Offsetting the screed ......................................................................................... 31
5 Levelling .................. ............................................................................... ........... 32
5.1 Slope controller ...................................................................................... ........... 32
5.2 Mounting the sensor arm ................................................................................. 33
5.3 Mounting the grade control system ................................................ ............. 33
5.4 Setting up the sensor arm ................................................................................. 34
5.5 Big ski 9 m, big ski 13 m .. ................................................................................ 35
Mounting the big ski bracket on the crossbeam ....................... ........... 37
Mounting the swivel arms .......................................................................... 38
Mounting the centre element ..................................................................... 39
Extending the big ski ..................................................................................... 40
Mounting the sensor bracket ........................................................ ............. 41
Mounting and aligning the sensors ................................................ ......... 42
Mounting the distributor box ......................................................... ............. 43
Connection diagram ...................................................................................... 44
6 Automatic steering unit ..................................................................................... 45
6.1 Mounting the automatic steering unit on the paver finisher ................... 46
Mounting and aligning the sensor ................................................ ........... 47
Connecting the sensor .................................................................................. 47
Automatic steering unit operating instructions ............ ......................... 48
7 Emergency stop during feeder
operation .............................................................................................................. 49
8 Limit switch ............................................................................................ ........... 50
8.1 Auger limit switches
(left and right) - mounting the PLC version ................................................. 50
9 Screed ..................................................................................................................... 51
10 Electrical connections ...................................................................................... 51
10.1 Machine operation without remote control / side board ........................... 52
7
F10 Maintenance ....................................................................................... 1
1 Notes regarding safety ..............................................................................
............. 1
F22 Maintenance review .. ........................................... .......................... 1

1 Maintenance review ............................................................................................ 1
F31 Maintenance - conveyor ................................................................... 1

1 Maintenance - conveyor ..................................................................................... 1
1.1 Maintenance intervals .......................................................................... ............. 2
1.2 Points of maintenance ....................................................................................... 3
Chain tension, conveyor (1) ............................................................... ........... 3
Conveyor drive - drive chains (2) ................................................................. 5
Conveyor deflectors /
conveyor plates (3) ......................................................................................... 6
F40 Maintenance - auger assem bly ......................... .......................... 1

1 Maintenance - auger assembly ......................................................... ............... 1
1.1 Maintenance intervals ........................................................................................ 2
1.2 Points of maintenance ........................................................................................ 4
Outer auger bearing (1) ........ ........................................................ ............... 4
Auger planetary gear (2) ................................................................................ 5
Drive chains of the augers (3) ............. .............. ........................................... 6
Auger box (4) .......... ........................................................................................ 7
Seals and sealing rings (5) ... .......................................................................... 8
Gearbox bolts Check tightening (6) ................................................ ............. 9
Mounting screws - Outer auger bearing
Check tightening (7) ........................................................................................ 9
Auger blade (8) .................................................................................. ........... 10
F50 Maintenance - engine assembly ......................... .......................... 1

1 Maintenance - engine assembly ....................................................... ............... 1
1.1 Maintenance intervals ......................................................................................... 2
1.2 Points of maintenance ......................................................................... ............. 5
Engine fuel tank (1) ....... ................................................................................ 5
Engine lube oil system (2) ............................................................... ........... 6
Engine fuel system (3) ..... .............................................................. ............. 8
Engine air filter (4) ......... .............................................................................. 10
Engine cooling system (5) ............................................................ ............. 12
Engine drive belt (6) .......... ........................................................................... 14
8
F60 Maintenance - hydraulic system .................................................... 1
1 Maintenance - hydraulic system ....................................................................... 1
1.1 Maintenance intervals .......................................................................... ............. 2
Hydraulic oil tank (1) ......... ............................................................................ 4
Suction/return flow hydraulic filter (2) ...... ................................. ............. 6
Bleeding the filter ............................................................................................. 7
High-pressure filter (3) ................................................................................... 8
Pump distribution gear (4) ............................................................................ 9
Bleeder .............................................................................................. ........... 10
Hydraulic hoses (5) ........................................................................................ 11
Marking hydraulic hoses / storage period, period of use .................... 13
Auxiliary flow filter (6) ..................................................................... ........... 14
F71 Maintenance – drive units ............................................................ 1

1 Maintenance – drive units ....... ........................................................................... 1
Chain tension (1) .............. ................................................................ ............. 5
Bottom plates (2) .............................................................................. ............. 8
Rollers (3) ......................................................................................................... 9
Planetary gear (4) ......................................................................................... 10
Screw connections ......................................................................................... 12
F81 Maintenance - electrical system ..................................................... 1

1 Maintenance - electrical system ......................................................................... 1
1.1 Maintenance intervals ......................................................................................... 2
Batteries (1) ..................................................................................................... 3
Alternator (2) ................................................................................... ............... 4
Insulation faults ................................................................................. ............. 5
Cleaning the generator .................................................................................. 6
Electrical fuses / relays (3) ............................................................................. 7
Fuses in terminal box (B) .. ............................... ............................... ........... 8
Relays in terminal box (C) .............................................................. ......... 10
Relays in the engine compartment (E) ..................................................... 12
F90 Maintenance - lubricating points ................................................... 1

1 Maintenance - lubricating points...................................................... ............... 1
1.1 Maintenance intervals ....................................................................................... 2
Central lubrication system (1) ......... ............................................................ 3
Bearing points (2) .......................................................................................... 7
9
F100 Tests, stopping ................................................................................... 1
1 Tests, checks, cleaning, stop ping .................................................................... 1
2 General visual inspection .................................................................................. 3
3 Inspection by an expert ........................................................................ ............. 3
4 Cleaning ................................................................................................................. 4
5 Preserving the paver finisher .............................................................. ............. 5
5.1 Shutdowns for up to 6 months ......................................................................... 5
5.2 Shutdowns lasting from 6 months to 1 year .......................................... ........... 5
5.3 Recommissioning the machine ............................................................. ........... 5
6 Environmental protection, disposal ..................................................... ............. 6
6.1 Environmental protection .................................................................... ............. 6
6.2 Disposal ................................................................................................................. 6
F110 Lubricants and operating

substances .......................................................................... .............. 1
1 Lubricants and operating substances ............................................................. 1
1.1 Capacities .............................................................................................................. 3
2 Lubricant specifications ........................................................................ ............. 4
2.1 Engine .................................................................................................................... 4
2.2 Cooling system ...................................................................................................... 4
2.3 Hydraulic system ................................................................................................. 4
2.4 Pump distribution gear ........................................................................ ............. 4
2.5 Drive unit planetary gear ...................................................................... ............. 5
2.6 Auger drive planetary gear ............................................................................... 5
2.7 Auger box .............................................................................................................. 5
2.8 Grease ..................................................................................................... ............. 5
2.9 Hydraulic oil ........................................................................................................... 6
10
V Preface
Translation of the original operating instructions.
If the vehicle is to be operated safely, the information provided in these operating in-
structions will be required. The information is provided in a concise, clearly structured
form. The individual chapters are arranged in alphabetical order. and every chapter
starts with page 1. The individual pages are identified by the chapter letter and the
page number.
Example: Page B 2 is the second page of chapter B.
These operating instructions cover various vehicle options. Make sure that during op-
eration and maintenance work the description appropriate to the vehicle option is
used.
In the interest of continued development, the manufacturer reserves the right to make
changes to the vehicle (which will not, however, change the essential features of the
type of vehicle described)without updating the present operating instructions at the
same time.
Dynapac (China) Compaction & Paving Equipment Co., Ltd.

No.38, Quanwang Road,
Wuqing High Tech Industrial Park,301700,
Tianjin, China
www.dynapac.com
V1
1 General safety instructions
1.1 Laws, guidelines, accident prevention regulations
A The locally applicable laws, guidelines and accident prevention regulations must al-
ways be observed, even if these are not expressly named here.
The user himself/herself is responsible for compliance with the resulting regulations
and measures!
A The following warnings, prohibitive symbols and instructive symbols indicate dangers
for persons, the vehicle and the environment due to residual risks when operating the
vehicle.
A Failure to observe this information, prohibitions and instructions can result in life-
threatening injuries!
A The "Guidelines for the Correct Use and Application of Paver Finishers" compiled by
Dynapac must also be observed!
V2
1.2 Safety signs, signal words
In the safety instructions, the signal words "Danger", "Warning", "Caution", "Note" are
positioned in the coloured title block. They follow a certain hierarchy; in combination
with the warning symbol, they indicate the severity of the danger or the type of note.
"Danger"!
DANGER
Danger of personal injury.
Indication of an immediately threatening danger that result in fatal or severe injuries
unless the corresponding actions are taken.
"Warning" !
WARNING
Indication of a possible danger that can result in fatal or se-
vere injuries unless the corresponding actions are taken.
"Caution" !
CAUTION
Indication of a possible danger that result in moderate or mi-
nor injuries unless the corresponding actions are taken.
"Note" !
NOTE
Indication of a possible drawback unless the corresponding
actions are taken, e.g. unwanted conditions or consequences can occur.
1.3 Other supplementary information
Other information and important explanations are identified by the following picto-
grams:
Precedes safety instructions that must be observed in order to prevent danger to per-
f sonnel.
Precedes notes that must be observed to prevent damage to equipment.

m
A Precedes general notes and explanations.
V3
1.4 Warnings
Warning on a dangerous area or hazard!

Failure to observe the warnings can result in life-threatening inju-
ries!
Warning on danger of being pulled in!
In this working area/on this element there is a danger of being pulled

m in by rotating or conveying elements!
Only carry out activities with elements switched off!
Warning on dangerous electrical voltage!
All maintenance and repair work on the screed's electrical system

m must always be carried out by an electrician!
Warning on suspended loads!
Never stand under suspended loads!

m
Warning on danger of crushing!
m There is a danger of crushing when certain components are operat-

ed, or certain functions or vehicle movements are carried out.
Always make sure that there are no persons within the endangered
areas!
Warning on hand injuries!
Warning on hot surfaces or hot liquids!
V4
Warning on danger of falling!
Warning on dangers posed by batteries!
Warning on hazardous or irritating substances!
Warning on substances which constitute a fire hazard!
Warning on gas bottles!
V5
1.5 Prohibitive symbols
Opening/walking on/reaching in/carrying out/setting up are prohibit-

ed during operation or while the drive engine is running!
Do not start engine/drive!

Maintenance and repair work may only be carried out with the diesel
engine shut down!
Spraying with water is prohibited!
Extinguishing with water is prohibited!
Unauthorised maintenance is prohibited!

Only qualified experts may conduct maintenance!
A Consult the Dynapac Service Department
Fire!, naked flames and smoking are prohibited!
Do not switch!
V6
1.6 Protective equipment
A Locally applicable regulations may require the wearing of various safety equipment!
Always observe these regulations!
Wear safety goggles to protect your eyes!
Wear suitable head protection!
Wear suitable hearing protection to protect your hearing!
Wear suitable safety gloves to protect your hands!
Wear safety shoes to protect your feet!
Always wear close-fitting work clothing!

Wear a warning vest to be seen in time to avoid accidents!
Wear respiratory equipment if breathing air is contaminated!
V7
1.7 Environmental protection
A The locally applicable laws, guidelines and accident prevention regulations for the
proper recycling and disposal of waste must always be observed, even if these are
not expressly named here.
Water-endangering substances like:
- Lubricants (oil, grease)

- Hydraulic oil
- Diesel fuel
- Coolant
- Cleaning liquids
must not get into the soil or sewer system during cleaning, maintenance and repair
work!
Substances must be caught, stored, transported and brought to pro-

fessional disposal sites in suitable containers!
Environmentally hazardous substance!
1.8 Fire prevention
A Locally applicable regulations may require suitable extinguishing agents to be carried

on the vehicle!
Always observe these regulations!
Fire extinguisher!
(optional equipment)
V8
1.9 Additional information
Also observe the manufacturer's documentation and additional doc-

m umentation!
A For example, the maintenance instructions of the engine manufac-

turer
Description / depiction applicable when equipped with gas heater!

m
Description / depiction applicable when equipped with electric heat-

m er!
t Used to indicate standard equipment.
o Used to indicate optional equipment.
V9
2 CE identification and Declaration of Conformity
(only applies to machines sold in the EU/EEC)
This machine has CE identification. This identification says that the machine fulfils the
basic health and safety requirements pursuant to the Machinery Directive 2006/42/
EC together with all other valid regulations. The scope of supply of the machine in-
cludes a Declaration of Conformity as specified in the valid regulations and amend-
ments together with harmonised standards and other valid provisions.
3 Guarantee conditions
A The guarantee conditions are included in the scope of supply of the machine.
This contains a complete specification of the valid conditions.
The guarantee becomes null and void if
- damage occurrs through malfunctions caused by improper use and incorrect oper-
ation.
- repairs or manipulations are carried out by persons who are neither trained nor au-
thorised accordingly.
- accessories or spare parts are used that cause damage and which are not ap-
proved by Dynapac.
V 10
4 Residual risks
These are risks that remain even if all possible measures and safety precautions
have been taken to help minimise dangers (risks) or to reduce their probability and
scope to zero.
Residual risks in the form of
- Danger to life and limb of persons at the machine

- Danger to the environment posed by the machine
- Damage to property and restricted output and functionality of the machine
- Damage to property in the operating range of the machine
caused by:
- wrong or improper use of the machine

- defective or missing safety devices
- use of the machine by untrained, uninstructed staff
- defective or damaged parts
- incorrect transport of the machine
- incorrect maintenance or repairs
- leaking operating substances
- emission of noise and vibrations
- impermissible operating substances
Existing residual risks can be avoided by complying and implementing the fol-
lowing:
- warnings at the machine

- warnings and instructions in the safety manual for paver finishers and in the oper-
ating instructions of the paver finisher
- Operating instructions of the machine operator
V 11
5 Sensibly predictable incorrect usage
Every kind of sensibly predictable incorrect usage of the machine constitutes misuse.
Incorrect usage makes the manufacturer's warranty null and void: the operator bears
sole responsibility.
Sensibly predictable incorrect usage of the machine includes:
- presence in the danger zone of the machine

- transporting persons
- leaving the operator's platform while the machine is operating
- removing protection or safety devices
- starting and using the machine outside the operator's platform
- operating the machine with the screed walkway plate hinged up
- failing to comply with the maintenance instructions
- omission or incorrect execution of maintenance or repair work
- spraying the machine with high pressure cleaners
V 12
A Correct use and application
A The "Guidelines for the Correct Use and Application of Paver Finishers" compiled by
Dynapac are included in the scope of delivery for the present machine. The
guidelines are part of the present operating instructions and must always be heeded.
National regulations are fully applicable.
The road construction machine described in these operating instructions is a paver

finisher that is suited for laying mixed materials, roll-down concrete or lean-mixed
concrete, track-laying ballast and unbound mineral aggregates for foundations for
paving.
The paver finisher must be used, operated and maintained according to the
instructions given in the present operating instructions. Any other use is regarded as
improper use and can cause injury to persons or damage to the paver finisher or other
equipment or property.
Any use going beyond the range of applications described above is regarded as
improper use and is expressly forbidden! Especially in those cases where the paver
finisher is to be operated on inclines or where it is to be used for special purposes
(construction of dumps, dams), it is absolutely necessary to contact the manufacturer.
Duties of the user: A "user" within the meaning of these operating instructions is
defined as any natural or legal person who either uses the paver finisher himself, or
on whose behalf it is used. In special cases (e.g. leasing or renting), the user is
considered to be the person who, in accordance with existing contractual agreements
between the owner and the user of the paver finisher, is charged with the observance
of the operating duties.
The user must ensure that the paver finisher is only used in the stipulated manner and
that all danger to life and limb of the operator, or third parties, is avoided. In addition
to this, it must be ensured that the relevant accident prevention regulations and other
safety-related provisions as well as the operating, servicing and maintenance
guidelines are observed. The user must also ensure that all persons operating the
paver finisher have read and understood the present operating instructions.
Mounting of attachments: The paver finisher must only be operated in conjunction

with screeds that have been approved by the manufacturer. Mounting or installation
of any attachments that will interfere with or supplement the functions of the paver
finisher is permitted only after written approval by the manufacturer has been
obtained. If necessary, the approval of local authorities must be obtained.
Any approval obtained from local authorities does not, however, make approval by
the manufacturer unnecessary.
A1
A2
B Vehicle description
1 Application
The Dynapac SD2550C / SD2550CS paver finisher is a paver finisher with a caterpil-
lar drive which is used for paving bituminous mixed material, roll-down or lean-mixed
concrete, track-laying ballast and unbound mineral aggregates for foundations for
paving.
B1
2 Description of assemblies and functions
15
14
13
19 16
12 1
18
11 10 9 4 7 6 5 8 3 17
Item Designation
1 t Material compartment (hopper)
2 t Push roller crossbar for truck docking
2 o Push roller crossbar for truck docking, hydraulically extendable
3 t Tube for sensor rod (direction indicator) and holder for levelling shoe
4 t Caterpillar drive
5 t Levelling cylinder for paving thickness
6 t Traction roller
7 t Crossbeam pull bar
8 t Paving thickness indicator
9 t Crossbeam
10 t Travel drive of the caterpillar drive
11 t Auger
12 t Screed
13 t Operator's platform (hydraulically movable)
14 t Operating panel (can be moved to either side)
15 o Protective roof
16 o Working lights
17 t Lane cleaner
18 o Hydraulic front hopper flap
19 o Asphalt fume control system
t = Standard equipment o = Optional equipment
B2
2.1 Vehicle
Construction
The paver finisher has a welded steel frame on which the individual components are
mounted.
The caterpillar drives compensate uneven areas on the ground; the suspension of the
attached screed additionally helps to attain high paving precision.
The continuously adjustable hydrostatic travel drive allows the speed of the paver fin-
isher to be matched to all work conditions.
The operation of the paver finisher is considerably facilitated by the automatic mate-
rial handling system, the independent travel drives and the clearly structured operat-
ing components and controls.
The following extra equipment (option) is available:
o Automatic levelling/slope control system
o Ultrasonic sensors for material transfer (controller)
o Additional cut-off shoe
o Larger working widths
o Automatic central lubrication system for the finisher and/or the screed
o Protective roof / cab
o Additional headlights, warning lamps
o Emulsion spraying system
o Fuelling system
o Camera system
o Asphalt fume control system
o 12 volt system
o Further equipment and upgrade options on request
B3
Engine: The paver finisher is driven by a water cooled diesel engine. For further de-
tails see the technical data and the engine's instruction manual.
Drive unit: Both caterpillar drives are directly driven by separate drives. They operate
directly, without any drive chains which require maintenance or servicing.
The tension of the caterpillar chains can be readjusted using tensioners.
A swivelling lane cleaner (o), which ensures an even passage during paving, is lo-
cated in front of each of the drive units. Small obstacles lying in the lane are cleared
away to the side.
Hydraulic system: The diesel engine drives the hydraulic pumps for all main paver
finisher drives via the attached distribution gear and its auxiliary drive shafts.
Travel drive: The continuously adjustable travel drive pumps are connected to the
travel drive engines by means of high pressure hydraulic hoses.
These hydraulic motors drive the caterpillar chains via planetary gears that are
mounted directly inside the drive wheels of the caterpillar chains.
Steering system/operator's platform: The independent hydrostatic travel drives al-

low the paver finisher to be turned on the spot.
Electronic synchronous control ensures precise straight-ahead travel.
The operating panel can be hydraulically shifted beyond the left/right outer edge of
the vehicle, providing the driver with a better view of the paving area in this position.
The entire operating panel can be swivelled for operation beyond the outer edge of
the vehicle, and can be additionally be locked in several positions along the control
platform.
Push roller crossbar: The push rollers for material trucks are fastened to a cross bar
that is pivoted at its centre. The paver finisher thus deviates less from its course and
paving in curves is made easier.
For adaptation to various truck design types, the push roller crossbar can be shifted
to two positions.
The hydraulically extendable push roller crossbar (o) allows different distances to the
rear wheels of material trucks to be infinitely compensated.
The engageable push roller damping hydraulically absorbs the shocks between the
material truck and paver finisher.
B4
Material compartment (hopper): The hopper inlet is equipped with a conveyor sys-
tem that empties the hopper and transfers the material to the auger.
The hopper can hold approx. 17.5 t.
To facilitate emptying and to improve material transport, each of the lateral covers of
the hopper can be hydraulically moved.
The hydraulic front hopper flaps (o) ensure that no material remains at the front of
the feeding hoppers.
Material transfer: The paver finisher is equipped with two conveyors driven sepa-
rately that transfer the material from the hopper to the augers.
By scanning the filling height during the paving procedure, the transfer amount or
speed is regulated fully automatically.
The drive is reversible (o).
Augers: The augers are driven and actuated independently from the conveyors. The
left-hand and the right-hand half of the auger can be controlled separately. The drive
system is fully hydraulic.
The conveying direction can be changed towards the centre or towards the outside.
This ensures that there is always a sufficient supply of material even if an excessive
amount of material is required at one side. The auger speed is continuously controlled
by sensors that monitor the material flow.
Height adjustment and extension of augers: Height adjustment and extension of

augers ensure optimum adaptation to a wide range of paving thicknesses and widths.
Different auger diameters are available (o)
When using ratchets for height adjustment, barrel nuts at the guide supports in the
rear wall are used to adjust the height.
Another variant allows the height to be regulated at the operating panel by means of
hydraulic cylinders (o).
Auger segments of different lengths can be attached to easily adapt to the different
paving widths.
B5
Levelling/slope control system: The slope control system (o) can be used to reg-
ulate the traction point on the left-hand or the right-hand side with a defined difference
to the opposite side.
To determine the actual value, the two traction crossbeams are linked with a slope
control rod.
The slope control system always operates in conjunction with the screed height ad-
justment of the opposite side.
By adjusting the height of the traction point of the crossbeam (traction roller), the pav-
ing thickness of the material or the laying height of the screed can be controlled.
Actuation occurs electro-hydraulically on both sides and can be controlled manually
by means of toggle switches or automatically by means of an electronic grade control
system.
Crossbeams / screed lifting device: The screed lifting device is used to lift the
screed during transportation. The screed's approach angle can be changed using the
eccentric adjustment facility on the crossbeam.
Depending on the paving condition requirements, the crossbeam can be moved
backwards or forwards. This adjustment enlarges the material space between the au-
ger and screed.
Automatic paving stop and screed charging/relieving: The automatic paving stop
prevents the formation of any screed marks caused by a stopped screed. When the
paver finisher stops (during a truck change), the screed remains in floating position
and relief pressure is applied, thus preventing the screed from sinking while station-
ary.
The screed relieving device puts a higher load on the traction unit, thus increasing the
traction.
Activating the screed charging device can improve the compacting result under dif-
ferent paving conditions.
Asphalt fume control system (o): An extraction system installed in the material
tunnel extracts and discharges asphalt fumes.
Central lubrication unit (o): The central lubrication pump fitted with a large lubricant
tank supplies grease to the various lubrication circuits through various flow dividers.
They supply lubricant to the service-sensitive points of lubrication (e.g. bearings) at
adjustable intervals.
B6
3 Danger zones
m In these vehicle working areas, there may be a risk of drawing in or crushing during
normal operation caused by rotating and conveying elements, or by components in
motion.
Danger of being pulled in!
Danger of crushing!
B7
4 Safety devices
4 5 6 7
10 11
12
3 2
B8
Item Designation
1 Hopper transport safeguard **
2 Screed lock, mechanical / hydraulic (o) **
3 Main switch
4 Emergency stop button
5 Horn
6 Ignition key
7 Lights **
8 Protective roof latch (o) **
9 Fire extinguisher (o)
10 Screed warning light (o) **
11 Covers, lateral flaps, coverings **
12 Rotary beacon (o)
** Located on both sides of the vehicle
m Safe operation is only possible if the control and safety devices are functioning
perfectly and if the protective equipment is fitted correctly.
m Check the function of these devices at regular intervals.
A Functional descriptions for the individual safety facilities can be found in the following
chapters.
B9
5 Technical data, standard configuration
5.1 Dimensions (all dimensions in mm)
2605
3825
3065
2670
1660
R6
5
400
950 3360
6600
6880
320
1995
2550
3500
3610
A For screed technical data, refer to the screed operating instructions.
B 10
5.2 Allowed angle of rise and slope
max. 15° max. 15°
max. 15° max. 15°
A Before operating your vehicle in an inclined position (gradient, slope, lateral inclina-
tion) which is above the specified limit value, please consult the customer service de-
partment for your vehicle!
5.3 Permissible approach angle
max. 13.5° max. 13.5°
B 11
5.4 Weights SD2550C (all weights in t)
Paver finisher without screed Approx. 15.5

Paver finisher with screed:
- V5100 Approx. 19.2
With extension parts for max.
Approx. xxx
working width, additionally max.:
With filled hopper
Approx. 17.5
Additionally max.
A For the weights of the screed and the screed attachments, see the operating instruc-
tions for the screed.
5.5 Weights SD2550CS (all weights in t)
Paver finisher without screed Approx. 15.5

Paver finisher with screed:
- V5100 Approx. 19.2
With extension parts for max.
Approx. xxx
working width, additionally max.:
With filled hopper
Approx. 17.5
Additionally max.
A For the weights of the screed and the screed attachments, see the operating instruc-
tions for the screed.
B 12
5.6 Performance data SD2550C
Continuously hydraulically
Maximum paving width

Minimum paving width
(without cut-off shoes)
(with extension parts)

(with cut-off shoe)
adjustable up to
Screed used
Basic width
V5100TV(E) 2.55 2.00 5.10 8.80 m

V5100TV 2.55 2.00 5.10 8.80 m
V6000TV(E) 3.00 2.45 6.00 9.70 m
V6000TV 3.00 2.45 6.00 9.70 m
R300TV(E) 3.00 - - 12.00 m
R300TV 3.00 - - 12.00 m
Transport speed 0-4 km/h

Operating speed 0 - 28 m/min
Paving height -150 - 350 mm
Max. grain size 40 mm
Theoretical paving performance 900 t/h
B 13
5.7 Performance data SD2550CS
Continuously hydraulically
Maximum paving width

Minimum paving width
(without cut-off shoes)
(with extension parts)

(with cut-off shoe)
adjustable up to
Screed used
Basic width
V5100TV(E) 2.55 2.00 5.10 8.80 m

V5100TV 2.55 2.00 5.10 8.80 m
V6000TV(E) 3.00 2.45 6.00 9.70 m
V6000TV 3.00 2.45 6.00 9.70 m
R300TV(E) 3.00 - - 14.00 m
R300TV 3.00 - - 14.00 m
Transport speed 0-4 km/h

Operating speed 0 - 28 m/min
Paving height -150 - 350 mm
Max. grain size 40 mm
Theoretical paving performance 1100 t/h
B 14
5.8 Travel drive/traction unit
Drive Hydrostatic drive, continuously controllable

Two separately driven caterpillar drives with rub-
Drive unit
ber grouser chains
Turning capacity Turning on the spot
Speed See above
5.9 Engine SD2550C
Make/type Cummins QSB 6.7-C260

Version 6-cylinder diesel engine (water-cooled)
Performance 170 kW / 231 hp (at 2200 rpm)
Pollutant emissions in
EU 3A / Tier 3
co-ordination with:
Fuel consumption, full load 47.2 l/h
Fuel consumption, 2/3 load 31.5 l/h
Fuel tank capacity (See chapter F)
5.10 Engine SD2550CS
Make/type Cummins QSB 6.7-C260

Version 6-cylinder diesel engine (water-cooled)
Performance 194 kW / 264 hp (at 2200 rpm)
Pollutant emissions in
EU 3A / Tier 3
co-ordination with:
Fuel consumption, full load 53.6 l/h
Fuel consumption, 2/3 load 35.8 l/h
Fuel tank capacity (See chapter F)
5.11 Hydraulic system
Hydraulic pumps via distribution gear

Pressure generation
(directly flanged to the engine)
Hydraulic circuits for:
- Travel drive
- Auger
- Conveyor
Pressure distribution - Tamper / vibration
- Operating functions
- Fan
- Clutch
- Separate hydraulic circuits for options
Hydraulic oil reservoir - volume (See chapter F)
B 15
5.12 Material compartment (hopper)
Volume Approx. 8.0 m3 = approx. 17.5 t

Minimum inlet height, centre 525 mm
Minimum inlet height, outside 530 mm
Hopper width, outside, open 3610
5.13 Material transfer
Type Dual conveyor belt

Width 2 x 655 mm
Conveyors Left and right auger separately controllable
Drive Hydrostatic, continuously controllable
Conveying volume controller Fully automatic via configurable switching points
5.14 Material distribution SD2550C
Auger diameter 430 mm

Hydrostatic central drive, continuously controlla-
ble independently of the conveyor
Drive Auger halves can be switched to opposite direc-
tions
Reversible direction of rotation
Auger height adjustment - Mechanically
Auger extension With extension parts (see auger extension chart)
5.15 Material distribution SD2550CS
Auger diameter 500 mm

Hydrostatic central drive, continuously controlla-
ble independently of the conveyor
Drive Auger halves can be switched to opposite direc-
tions
Reversible direction of rotation
Auger height adjustment - Mechanically
Auger extension With extension parts (see auger extension chart)
B 16
5.16 Screed lifting device
At standstill:
- Screed stop
- Screed stop with pretensioning
(max. pressure 50 bar)
Special functions
During paving:
- Screed charging
- Screed relieving
(max. pressure 50 bar)
Mechanical grade control
Levelling system Optional systems with and without
Slope control system
5.17 Electrical system
On-board voltage 24 V
Batteries 2 x 12 V, 88 Ah
33 kVA / 400 V
Generator (o)
60 kVA / 400 V
5.18 Permissible temperature ranges
Operation -5°C / +45°C

Storage -5°C / +45°C
B 17
6 Location of instruction labels and identification plates
1 4
11
50 2 5
73
52 51
27
22
22 21
3
6 52
24
20 54
60
22 21
28 29
26
30 53
8
23
25
22
22 21 32 31
B 18
9
10
xxxxxxxxxxxxxxxxx 72
40
42
41
71
70
10
B 19
6.1 Warning signs
No. Pictogram Meaning

- Warning - Operating instructions!
Danger due to improper operation. The
machine personnel must have read and
understood the safety, operating and
maintenance instructions for the ma-
chine before the machine is put into op-
1
eration! Failure to comply with the
operating and warning instructions can
cause severe or fatal injuries. Always re-
place lost operating instructions immedi-
ately! It is your personal responsibility to
take due care and attention!
- Warning - Switch off the engine and
remove the ignition key before per-
forming any maintenance and repair
work!
2 If the drive engine is left running or func-
tions are switched on, this can cause se-
vere or fatal injuries!
Switch the engine off and remove the ig-
nition key.
- Warning - Danger of crushing!

Crushing points can cause severe or fa-
3 tal injuries!
Maintain a safe distance from the dan-
ger area!
- Warning - Hot surface -

Danger of burning!
Hot surfaces can cause severe injuries!
4
Keep your hands at a safe distance from
the danger area! Use protective clothing
or protective equipment!
- Warning - Danger from fan!
Rotating fans can cause severe injuries
from cutting or severing fingers and
hands.
5
the danger area!
B 20
- Warning - Danger of crushing fingers
and hands with moving, accessible
machine parts!
Crushing points can cause severe inju-
6
ries with the loss of parts of the fingers
or hand.
the danger area!
- Warning - Spring-loaded part!

Performing work incorrectly can cause
7 severe to fatal injuries.
Always observe the maintenance in-
structions!
- Caution - Danger from incorrect tow-

ing!
Movements of the machine can cause
severe or fatal injuries.
8
The traction system brakes must be re-
leased before towing.
Always observe the operating instruc-
tions!
- Caution - Possible collision of parts!

The ratchet lever must always be swiv-
9 elled in.
tions!
- Caution - Possible collision of parts!

The Powermoon tripod must be mount-
10 ed correctly.
tions!
- Warning - Danger from running en-

gine!
If the drive engine is left running, this
11
can cause severe or fatal injuries.
Never open the engine hood while the
engine is running!
B 21
- Warning - Hazard from hydraulic res-
ervoir and from hydraulic oil under
pressure!
Escaping hydraulic oil under pressure
12
can pierce the skin and enter into the
body, causing severe or fatal injuries.
tions!
- Warning - Danger from tyres filled
with water!
Handling tyres filled with water incorrect-
13
ly can cause severe to fatal injuries.
tions!
B 22
6.2 Information signs
- Operating Instructions
20
Position of the storage compartment.
- Lifting point
21 Lifting the machine is only permitted at these lifting
points!
- Lashing point
22
Lashing the machine is only permitted at these points!
- Main battery switch

23
Position of the main battery switch.
- Diesel fuel
24
Position of the filling point.
- Diesel fuel, sulphur level < 15 ppm

24
Position of the filling point, specification.
- Fuel drainage point

25
Position of the drainage point.
B 23
- Engine oil
26
Position of the filling and control point.
- Engine coolant
27
- Hydraulic oil
28
Position of the filling point.
- Hydraulic oil level

29
Position of the control point.
- Engine oil drainage point

30
- Gearbox oil
31
- Gear oil drainage point

32
B 24
- Tamper speed adjuster

33
Position of the speed adjuster.
- Vibration, speed adjuster

34
Position of the speed adjuster.
B 25
6.3 Instructive symbols, prohibitive symbols, warning symbols
50 - Wear ear protection devices
51 - Do not enter the area!
52 - Do not spray the area or part with water!
53 - Warning on dangers posed by batteries!
54 - First aid kit
B 26
6.4 Danger symbols
No. Pictogram Meaning No.

- XN: Danger to health! This substance
can damage your health when absorbed
in the body!
Substance irritating to skin, eyes and res-
piratory system; can cause inflamma-
tions.
Avoid contact with the human body, also
avoid inhaling the vapours and seek
medical advice if feeling unwell.
60
- N: Environmentally hazardous sub-
stance! May cause immediate or delayed
danger to the eco-system when released
into the environment.
Do not release into the sewage system,
ground or environment, depending on
hazard potential. Comply with special dis-
posal regulations!
- Diesel fuel complies with EN590
B 27
6.5 Further warnings and operating instructions

- Important!
Let the engine reach operating tempera-
ture for 5 minutes at half speed after cold-
starting.
- Move the traction lever slightly
from its 0-position.
70 - Possibly adjust switch gear to neu-
tral position.
Apply the handbrake when the vehicle is
stationary. At the end of work, let the engine
run on for 5 minutes inneutral. Remove the
ignition key immediately after switching off
the engine.
- Warning - Hazard from unsupported

screed!
If the screed sags, this can cause severe
or fatal injuries! Insert screed lock only at
71
crown adjustment "zero". Screed lock
only for transportation! Do not enter or
work under screed only secured with
screed lock for transportation!
- Caution - Danger of high voltage in

vehicle electrical system!
Disconnect batteriesand electronics dur-
72 ing welding work or when charging the
batteries, or use a service watchdog
D978000024 in accordance with the cor-
responding instruction manual.
- Important!
Only use approved radiator anti-freeze.
Never mix different grades of radiator
73
anti-freeze.
tions!
B 28
- Overview "Tyre pressure / working width

74
/ speed preselection"
- Overview "Tyre pressure / working width

74
/ speed preselection"
- Engine start - All switches in neutral!

The engine cannot be started when func-
75 tions are switched on.
tions!
B 29
6.6 Identification label for the paver finisher (41)
Item Designation
1 Paver finisher type
2 Year of construction
3 Serial number of the paver finisher series
4 Max. permissible operating weight, incl. all extension parts, in kg
5 Max. permissible load on the front axle, in kg
6 Max. permissible load on the rear axle, in kg
7 Rated performance in kW
8 Product identification number (PIN)
A The punched vehicle identification number (VIN) on the paver finisher must match the
product identification number (9).
B 30
Identification plate for the paver finisher (valid from Year 2016/2017)
Item Designation
1 Paver finisher type
2 Max. permissible operating weight, incl. all extension parts, in kg
3 Serial number of the paver finisher series
4 Year of construction
5 Manufacturer
B 31
7 EN standards
7.1 Continuous sound pressure SD2550C, Cummins QSB 6.7-C260
m The operator always must use ear protection. The emission value at the ear of the
driver varies depending on the materials used for paving and may even rise above 85
dB(A). If no ear protection devices are used, hearing can be impaired.
The sound emission level of the paver finisher was measured under free-field condi-
tions according to EN 500-6:2006 and ISO 4872.
Sound pressure level at the operator’s position (

at the height of the head): LAF = 88.2 dB(A)
Sound capacity level: LWA = x108.2 dB(A)
Sound pressure level at the vehicle
Measuring point 2 4 6 8 10 12
Sound pressure level LAFeq
75.8 74.5 75.4 74.8 75.1 75.2
(dB(A))
7.2 Operating conditions during measurement
The diesel engine was running at maximum speed. The screed was lowered into
working position. Tamper and vibration unit were operated at min. 50%, while the au-
gers were operated at a minimum of 40% and the conveyors were operated at a min-
imum of 10% of their maximum speed.
7.3 Measuring point configuration
Hemispherical measuring surface with a radius of 16 m. The vehicle was at the cen-
tre. The measuring points had been assigned the following coordinates:
Measuring points 2, 4, 6, 8 Measuring points 10, 12

Co-ordinates X Y Z X Y Z
- 4.32 +10.4 11.36
±11.2 ±11.2 1.5
+4.32 -10.4 11.36
B 32
7.4 Continuous sound pressure SD2550CS, Cummins QSB 6.7-C260
m The operator always must use ear protection. The emission value at the ear of the
driver varies depending on the materials used for paving and may even rise above 85
dB(A). If no ear protection devices are used, hearing can be impaired.
The sound emission level of the paver finisher was measured under free-field condi-
tions according to EN 500-6:2006 and ISO 4872.
Sound pressure level at the operator’s position

(at the height of the head): LAF = 87.6 dB(A)
Sound capacity level: LWA = 107.9 dB(A)
Sound pressure level at the vehicle
Measuring point 2 4 6 8 10 12
Sound pressure level LAFeq
76.2 73.8 73.3 75.2 75.2 75.4
(dB(A))
7.5 Operating conditions during measurement
The diesel engine was running at maximum speed. The screed was lowered into
working position. Tamper and vibration unit were operated at min. 50%, while the au-
gers were operated at a minimum of 40% and the conveyors were operated at a min-
imum of 10% of their maximum speed.
7.6 Measuring point configuration
Hemispherical measuring surface with a radius of 16 m. The vehicle was at the cen-
tre. The measuring points had been assigned the following coordinates:
Measuring points 2, 4, 6, 8 Measuring points 10, 12

Co-ordinates X Y Z X Y Z
- 4.32 +10.4 11.36
±11.2 ±11.2 1.5
+4.32 -10.4 11.36
B 33
7.7 Vibration acting on the entire body
When the machine is used properly, the weighted effective acceleration values at the
driver’s seat of aw= 0.5 m/s2 according to DIN EN 1032 are not exceeded.
7.8 Vibrations acting on hands and arms
When the machine is used properly, the weighted effective acceleration values at the
driver’s seat of aw= 2.5 m/s2 according to DIN EN ISO 20643 are not exceeded.
A Electrical or electroniccomponents and their arrangement may only be modified after

written approval by the manufacturer has been obtained.
B 34
B 34
C 11 Transportation
1 Safety regulations for transportation
Accidents can happen when the paver finisher and the screed are not properly pre-
pared for transportation or when transportation is carried out improperly!
Reduce both the paver finisher and the screed to their basic widths. Remove all pro-
truding parts (such as the automatic levelling system, auger limit switches, aprons,
etc.). When transportingunder a special permit, secure these parts!
Close the hopper lids and engage the hopper transport safeguards. Lift the screed
and engage the screed transport safeguards. Convert the protective roof and engage
the latch.
Pack all parts that are not permanently fixed to the paver finisher and the screed into
the appropriate boxesand into the hopper.
Close all coverings and check that they are securely seated.
Gas bottles must not be transported on the paver finisher or on the screed.
Disconnect the gas bottles from the gas system and protect them with their caps. Use
a separate vehicle to transport them.
When loading via ramps, there isa risk that the machine will slip, tilt or overturn.
Drive carefully! Keep people away from the danger area!
Additional stipulati ons for transportation on public roads:
Caterpillar paver finishers must not be driven as self-propelling vehicles on public

roads.
Note that in other countries different regulations may apply.
The operator must be in the possession of a valid permit for vehicles of this type.
The operating panel must be moved to the side of the oncoming traffic and secured
in this position.
The driving lights must be properly adjusted.
Only attachments and extension parts maybe transported in the hopper, no material
or gas bottles!
If necessary, the operator must be assisted by a second person when driving on pub-
lic roads – especially at road crossings and junctions.
C 11 1
2 Transportation on low-bed trailers
m Reduce the paver finisher and the screed to their basic widths; also remove any at-
tached side plates.
The maximum approach angle is indicated in the section entitled "Technical data"!
m Check the fill level of the operating substances so that these do not escape when driv-
ing on an incline.
m Attachment and loading equipment must meet the conditions of the applicable acci-
dent prevention regulations!
m The weight of the paver finisher must be taken into consideration when selecting the
attachment and loading equipment!
2.1 Preparations
- Prepare the paver finisher for transportation (see chapter D).

- Remove all overlaying or loose parts from finisher and screed (see also Operating
instructions for the screed). Store these parts in a safe place.
m Move the auger to the uppermost position to avoid collisions!
f When the screed is operated with the optional gas heat-

ing system:
- Remove the gas bottles for the screed heating system:

- Close the main shut-off valves and the bottle valves.
- Turn off the valves on the bottles and remove the gas
bottles from the screed.
- Transport the gas bottles on a second vehicle; heed all applicable safety regula-
tions.
C 11 2
.
Operation Buttons
- Deactivating the function lock
- Activate set-up mode.
- Close the hopper lids.
- Engage both hopper transport safe-

guards.
- Lift the screed.
- Extend levelling cylinders

completely.
- Retract the screed parts until the screed

matches the basic width of the paver fin-
isher.
- Deactivate set-up mode.
C 11 3
3 Securing the load
A The following instructions for securing the load on the low-bed trailer consist merely
in examples of how to secure the load correctly.
A Always comply with the local regulations for securing the load and for correct use of
load securing equipment.
A Normal driving mode also includes emergency braking, evasive manoeuvres and
poor road surfaces.
A Use should be made of the different methods available for securing loads (positive fit,
force connection, diagonal lashing, etc.) in accordance with the specific transport ve-
hicle.
m The low-bed trailer must have the necessary number of lashing points with lashing
strength of LC 4,000 daN.
m The total height and total width must not exceed the maximum permissible dimen-
sions.
m The ends of lashing chains and straps must be secured to prevent them working
loose and falling down unintentionally!
3.1 Prepare the low-bed trailer
m The floor of the loading space must always be undamaged, free of oil and mud, dry
(residual moisture is permitted without accumulations of water) and swept clean!
C 11 4
3.2 Driving onto the low-bed trailer
f Make sure that there are no persons in the danger area during loading.
- Use the work gear and low engine speeds to drive onto the low-bed trailer.
C 11 5
3.3 Lashing equipment
Use the load securing equipment, lashing straps and chains belonging to the vehicle.
Additional shackles, eyebolts, edge safeguards and non-slip mats may be needed,
depending on the type of load securing equipment.
m Always comply with the stated values for permitted lashing force and load rating!
m Always tighten the lashing chains and straps handtight (100-150daN).
- Lashing chain
permissible lashing force LC 4,000 daN
- Lashing straps
permissible lashing force LC 2,500 daN
- Shackles
Load rating 4,000 daN
- Eyebolts
Load rating 2,500 daN
- Edge safeguards for lashing straps
- Non-slip mats
m Lashing equipment must be checked by the user for any signs of damage before use.
On detecting any signs of damage that impact on safety, the lashing equipment must
be withdrawn from any further use.
C 11 6
3.4 Loading
m Pay attention to load distribution during loading!

In some vehicles, the kingpin load is too low so that the load has to be positioned fur-
ther to the back of the vehicle (A).
Always heed the details regarding load distribution stipulated for the vehicle together
with the centre of gravity of the paver finisher.
Comply with the following if the paver finisher has to be placed in the front section of
the low-bed trailer (B) for load distribution reasons or on account of the length of the
paver finisher:
- The paver finisher must stand freely if the push rollers would only touch the goose-
neck half way up (C).
- There must be a positive fit between the paver finisher push rollers and the low-bed
trailer if the push rollers are in full contact with the low-bed trailer (D).
C 11 7
3.5 Preparing the machine
4 1 5
2 3 6
7
After the machine has been positioned on the low-bed trailer, the following prepara-
tions must be carried out:
- For movable platform: Set the retaining bolt properly (1).

- Close the hopper and set the hopper transport safeguards (2) on both sides.
- Position the non-slip mats under the screed across the whole width of the vehicle
(3) and lower the screed.
- Switch off the paver finisher.
- Attach and secure the protective hood (4) to protect the operating panel.
- Lower the roof and set the retainers (5) properly on both sides.
- For machines without roof: remove the exhaust extension pipe after it has cooled
down.
- Fold up the walkway plates of the screed and fasten on both sides using lashing
straps (6) and any possibly existing hook springs (7).
C 11 8
4 Securing the load
4.1 Securing at the sides
m Diagonal lashing secures the paver finisher at the side using the lashing points on the
paver finisher and on the low-load trailer.
Fasten the lashing chains as shown.
4.2 Securing at the front
m Diagonal lashing secures the paver finisher at the front using the lashing points on
the paver finisher and on the low-load trailer. Fasten the lashing chains as shown.
m The lashing angles should be "ß" between 6°-55° and "a" between 20°-65°!
C 11 9
4.3 Securing at the rear - screed with side board
m Diagonal lashing secures the paver finisher at the rear, at right angles to the direction
of travel using the lashing points on the paver finisher (eyebolts) and on the low-load
trailer. Fasten the lashing straps as shown.
Screw the supplied eyebolts first of all in the holes provided in the arms.
C 11 10
4.4 Securing at the rear - screed without side board
Step 1: fasten lashing straps
m Diagonal lashing secures the paver finisher at the rear using the lashing points on the
Fasten the lashing straps as shown.
Step 2: fasten lashing chains
m Diagonal lashing secures the paver finisher at the rear using the lashing points on the
Fasten the lashing chains as shown.
C 11 11
5 Control panel transport safeguard:
1
f During transportation in road traffic and
when transporting the vehicle on trans-
porters, the control panel must be se-
cured in the central position!
- Remove the locking pin (1) from its

storage compartment (press pushbut-
ton) and insert into locking aperture
(2).
m To be able to set the lock, the panel must

be positioned centrally above the ma- 2
chine frame.
C 11 12
5.1 After transportation
- Remove the attachment devices.

- Raise the protective roof (o):
A See section entitled "Protective roof"
For a paver finisher without roof:
- Mount the exhaust extension pipe.
- Lift the screed to the transportation position.

- Start the engine and drive from the trailer at a low engine/traction speed.
- Park the paver finisher in a secure spot, lower the screed and switch off the engine.
- Remove the key and/or cover the operating panel with the protective hood and se-
cure it.
C 11 13
6 Protective roof (o)
4
The protective roof can be raised and
lowered with a manual hydraulic pump.
A The exhaust pipe is lowered or raised to-

gether with the roof.
3
- Remove the lower section of the pump
lever (1) from the storage compart-
ment, and connect to the upper sec-
tion using a pipe (2).
- Lower the roof: The locks (3) on both
sides of the roof must be released.#
5
- Raise the roof: The locks (4) on both
sides of the roof must be released. 2
- Set the adjustment lever (5) to the
"Raise" or "Lower" position.
- Raise the roof: The lever points for- 1
wards.
- Lower the roof: The lever points
backwards.
- Operate the pump lever (1) until the roof has reached the upper or lower limit posi-
tion.
- Roof in uppermost position: Set the locks (3) on both sides of the roof.
- Roof lowered: Set the lock (4) on both sides of the roof.
m If the vehicle is equipped with a protective roof, the engine hood must be closed be-
fore lowering the roof!
C 11 14
7 Transportation
m Reduce the paver finisher and the screed to their basic widths; also remove any at-
tached side plates.
7.1 Preparations
- Prepare the paver finisher for transportation (see chapter D).

- Remove all overlaying or loose parts from finisher and screed (see also Operating
instructions for the screed). Store these parts in a safe place.
f When the screed is operated with the optional gas heat-

ing system:
- Remove the gas bottles for the screed heating system:

- Close main shut-off valves and bottle valves.
- Turn off the valves on the bottles and remove the gas
bottles from the screed.
- Transport the gas bottles on a second vehicle; heed all applicable safety regula-
tions.
C 11 15
.
Operation Buttons
- Deactivating the function lock
- Activate set-up mode.
- Close the hopper lids.
- Engage both hopper transport safe-

guards.
- Lift the screed.
- Extend levelling cylinders

completely.
- Retract the screed parts until the screed

matches the basic width of the paver fin-
isher.
- Deactivate set-up mode.
C 11 16
7.2 Driving mode
Operation Buttons
- Set the fast/slow switch to "Hare" if neces-

sary.
- Turn the preselector to "zero".
- Swivel the drive lever to maximum.

f The machine already advances slightly
on deflecting the drive lever!
- Adjust required vehicle speed with the

preselector.
- To stop the machine, swivel the drive le-

ver to the middle setting and set the
preselector to "zero".
f Press the emergency stop button when a dangerous situation arises!
C 11 17
8 Loading by crane
Use only lifting gear that can bear the load.

(See chapter B for weights and dimensions).
Attachment and loading equipment must meet the conditions of the applicable acci-
dent prevention regulations!
The vehicle's centre of gravity is dependent on the screed which is mounted.
C 11 18
A Four lifting eyes (1, 2) are provided for loading the vehicle with a crane.
A Depending on the type of screed which is used, the paver finisher's centre of gravity,
with the screed mounted, is located in the area of the drive unit's rear reversing
roller (3).
- Secure vehicle wherever it is parked up.

- Engage the transport safeguards.
- Remove any attachments and extension parts from the paver finisher and the
screed until the basic width has been attained.
- Take off all protruding or loose parts and the gas bottles of the screed heater (see
chapters E and D).
- Lower the protective roof (o):
A See section entitled "Protective roof"
- Attach lifting gear to the four attachment points (1, 2).
mThe max. permissible attachment point load is 73.5 kN.

mThe permissible load applies in the vertical direction!
mMake sure that the paver finisher remains in a horizontal position during transportation!
C 11 19
9 Towing
f Heed all regulations and apply all safety measures applicable for towing heavy con-
struction machines.
m The towing vehicle must be capable of securing the paver finisher, even on slopes.
Use only approved tow bars!

If necessary, remove any attachments and accessories from the paver finisher and
the screed until the basic width has been attained.
A A hand pump (1) is located in the engine compartment (left side); it must be actuated
to be able to tow the machine.
Pressure for releasing the traction system brakes is built up with the hand pump.
- Release lock nut (2), screw threaded

dowel (3) into pump as far as possible
and secure with lock nut. 1
- Actuate lever (4) of hand pump until
sufficient pressure has been built up
and traction system brakes have been
released.
3
m On completion of the towing process, re-
store the initial status.
2
m Only release the traction system brakes

when the machine is sufficiently secured
4
against accidental rolling or is already

properly connected to the towing vehi-
cle.
C 11 20
A Two high-pressure cartridges (6) are
located on both of the travel drive
pumps (5).
The following activities must be carried
out to activate the towing function:
- Loosen lock nut (7) half a turn.

- Screw in the bolt (8) until increased re-
sistance occurs. Then screw the bolt a
further half turn into the high-pressure 5
cartridge.
- Tighten the lock nut (7) to a torque
of 22 Nm.
m On completion of the towing process, re-

store the initial status.
- Attach the tow bar to the coupling (9)

located in the bumper.
8
A Now carefully and slowly tow the paver

finisher out of
the construction area.
m Only ever tow the shortest distance to

the means of transport or the next park-
ing possibility.
m The max. permissible towing speed

is 10 m/min!
In hazardous situations, a towing speed
of 15 m/min is only permitted temporari-
9
ly.
m The max. permissible towing eye (9)

load is: 200 kN
C 11 21
10 Safely parking the vehicle
m When the paver finisher is parked at a lo-

cation accessible to the public, it must be
secured in such a way that unauthorised
persons or playing children cannot dam-
age the vehicle.
- Pull off the ignition key and the main 1

switch (1) and take it with you – do not
hide them somewhere on the ma-
chine.
- Protect the operating panel with the

dust cover (2) and lock it.
- Store loose parts and accessories in a
safe place.
C 11 22
D 11 Operation
1 Safety regulations
f Starting the engine, the travel drive, the conveyor, the auger, the screed or the lifting
devices can cause injuries or even the death of persons.
Make sure before starting any of these devices that no-one is working at, in or be-
neath the paver finisher or within its danger area!
- Do not start the engine or do not actuate any controls when this is expressly forbid-
den!
Unless otherwise specified, the controls may only be actuated when the engine is
running!
f Never crawl into the auger tunnel or step into the hopper or onto the conveyor. Dan-
ger to life and limb!
- Always make sure during work that no-one is endangered by the vehicle!
- Ensure that all protective covers and hoods are fitted and secured accordingly!
- Immediately rectify damage which as been ascertained! Operation must not be
continued when the vehicle is defective!
- Do not let any persons ride on the paver finisher or the screed!
- Remove obstacles from the road and the work area!
- Always try to choose a driver’s position that is opposite to the flowing traffic! Lock
the operating panel and the driver’s seat.
- Maintain sufficient safety clearance from overhanging objects, other vehicles and
points of danger!
- Be careful when travelling on rough terrain to keep the paver finisher from slipping,
tipping or turning over.
f Always be the master over the vehicle; never try to use it beyond its capacities!
D 11 1
2 Controls
2.1 Operating panel
D 11 2
m General notes on adherence to CE regulations
All detent switch functions which may pose a risk on starting the diesel engine (auger
and conveyor conveying function) are set to the STOP function in the case of EMER-
GENCY STOP or restarting the control system. If settings are changed when the die-
sel engine is stopped ("AUTO" or "MANUAL"), these are reset to "STOP" on starting
the diesel engine.
The "Turning on the spot" function is reset to "Straight-ahead travel".
Item Designation Brief description
The entire operating panel can be swivelled for operation be-

yond the outer edge of the vehicle.
- Press latch (1), swivel operating panel to the required
position using the handle (A) and allow latch to engage
Swivel latch of again in one of the intended detent positions.
1 operating panel
(o)
f Only adjust the operating panel position whilst the vehi-
cle is stationary!
A The operating panel can only be swivelled beyond the

outer edge of the vehicle if a telescopic control panel is
fitted!
The operating panel can be shifted to several positions

on the left- and right-hand sides of the vehicle.
- Release the panel latch (2) and slide the panel console to
Swivel latch of the required position using the handle (A).
2 shift operating - Insert panel latch (2) into one of the detent positions (B).
panel m Make sure it is latched properly!
f Only adjust the operating position whilst the vehicle is

stationary!
Vandalism protec- On completion of work, secure the operating panel with the
3
tion facility vandalism protection facility.
To lock the vandalism protection facility.

4 Lock
- Turn the handle to the locking position and lock.
D 11 3
10
12
17 15 11 13
16
D 11 4
In the case of an emergency (danger to persons, possible col-

lision, etc.), press in the button!
- Pressing the emergency stop button switches the engine,
the drives and the steering system off.
Making way, lifting the screed or other actions are then no
Emergency stop
10 longer possible! Danger of accidents!
button
- The emergency stop button does not shut off the gas heat-
er system (o).
Close the main shut-off valve and the valves on the bottles
by hand!
- To restart the engine, the button must be pulled out again.
To activate the ignition voltage by turning the key.

- Switch off by turning the key back to its starting position.
A After activating the ignition voltage, the input and dis-

play terminal requires a few seconds for the booting
process.
11 Ignition lock
A On shutting off the vehicle, first switch off the ignition,
then deactivate the main switch.
A Before the main battery switch is deactivated, a period

of at least 10 seconds must elapse after switching off
the vehicle.
Energizes starter motor while pressed. All emergency stop but-

12 Starter tons (on the operating panel and the remote controls) must be
pulled out.
D 11 5
10
12
17 15 11 13
16
D 11 6
For switching on the paver finisher functions and for continu-

ously regulating the road speed – forward or reverse.
Zero position: engine at idling speed; no travel drive;
- To swivel the drive lever out, release by pulling the handle
up.
Depending on the position of the drive lever, the following func-
tions can be activated:
1st position:
- Conveyor and auger on.
2nd position:
- Screed motion (tamper/vibration) on; travel
drive on; increase speed until the stop is reached.
Drive lever
13
(traction)
A Use the preselector to set the maximum speed.
f The vehicle speed cannot be reduced to "0" with the

preselector. The machine advances slightly with de-
flected drive lever, even if the travel drive preselector is
set to "zero"!
A The drive is locked by an engine start with drive lever

out of center position.
To start the drive, the lever must be put into center po-
sition before.
A When changing over between forwards and reverse tra-

vel, the drive lever must remain briefly in neutral.
D 11 7
10
12
17 15 11 13
16
D 11 8
For setting the maximum speed that can be reached when the
drive lever is at its stop.
A The scale roughly matches the speed in m/min (during

Travel drive prese- paving).
15
lector
f The vehicle speed cannot be reduced to "0" with the
preselector. The machine advances slightly with de-
flected drive lever, even if the travel drive preselector is
set to "zero"!
The steering wheel movement is transferred electrohydrauli-

cally.
Steering potenti-
16
ometer A For precise adjustments (position "0" = straight-ahead),
see the straight-ahead travel synchronisation.
For turning on the spot, see switch (Turning on the
spot).
Press in the case of emergencies and to indicate when the ve-

hicle starts to move!
17 Horn
A The horn can also be used to communicate acoustically
with the truck driver for material loading!
D 11 9
18 19 20 21 22 23
D 11 10
Button with detent switch function and LED feedback:

Working - For switching on the front working lights
18 lights, front - Switch OFF by pressing the button again
ON / OFF (o)
f Avoid dazzling other road
users!

Working - For switching on the rear working lights
19 lights, rear - Switch OFF by pressing the button again
ON / OFF (o)
f Avoid dazzling other road
users!

- For switching on the rotary beacon
Rotary beacon - Switch OFF by pressing the button again
20
ON / OFF (o)
A Switch on for safety on roads and in the construction
site area

Seat heating
21 - For switching on the seat heating
ON / OFF (o)
- Switch OFF by pressing the button again
Filling pump Button with detent switch function and LED feedback:
22 Fuel tank - For switching on the filling pump
ON / OFF (o) - Switch OFF by pressing the button again

Windscreen wiper
23 - For switching on the windscreen wiper
ON / OFF (o)
D 11 11
24 25 26 27 28 29
D 11 12
Pushbutton function with LED feedback:

- To move the control panel to the left
24
Move control panel m The platform lock must be released before moving the
control panel!
to the left
f On actuation, note danger zones of moving parts of the

vehicle!

- To move the control panel to the right
Move control panel
25
to the right
vehicle!

- To hydraulically extend the push roller
Push roller crossbar.
26
Extend(o)
vehicle!

- To hydraulically retract the push roller
Push roller crossbar.
27
Retract (o)
vehicle!
Detent switch function and LED feedback:
- Press both buttons simultaneously to activate push
26 Push roller roller damping.
+ damping - Switch OFF by pressing one of the two buttons.
27 ON / OFF (o)
A Push roller damping hydraulically absorbs the shocks
between the material truck and paver finisher.
D 11 13
24 25 26 27 28 29
D 11 14

- To hydraulically extend the screed lock.
Extend screed l
28
ock (o)
m Before retracting and extending, lift the
crossbeams slightly over the locking bolts (lift screed)!

- To hydraulically retract the screed lock.
Retract screed lock
29
(o)
m Before retracting and extending, lift the
crossbeams slightly over the locking bolts (lift screed)!
D 11 15
30 31 32 33 34 35
D 11 16
30 not used
31 not used
32 not used

Extraction
33 - To actuate the asphalt fume control system
ON / OFF (o)

Windscreen wip-
34 - For switching on the windscreen wipers
ers ON / OFF (o)
Windscreen Detent switch function and LED feedback:

washer system + - To actuate the windscreen washer system +
35
Windscreen wiper windscreen wipers
ON / OFF (o) - Switched OFF with time control
D 11 17
36
37
39
38
D 11 18
Pushbutton function:
- To close the left half of the hopper
A Separate actuation (o):

Left hopper Is required when paving in spaces where there is only
36 limited space at one side or when obstacles obstruct
Close
truck unloading.

vehicle!
- To close the right half of the hopper
A Separate actuation (o):

Right hopper Is required when paving in spaces where there is only
37 limited space at one side or when obstacles obstruct
Close
truck unloading.

vehicle!
- To open the left half of the hopper
Left hopper A If the hoppers are hydraulically actuated at the same

38 time, both the left and the right switch can be used for
Open actuation.

vehicle!
- To open the right half of the hopper
Right hopper A If the hoppers are hydraulically actuated at the same

39 time, both the left and the right switch can be used for
Open actuation.

vehicle!
D 11 19
40
41
43
42
D 11 20
- To extend the left half of the screed
40
Left screed A This function is not used in vehicle configurations with a
Extend screed which cannot be extended.

vehicle!
- To extend the right half of the screed
41
Right screed A This function is not used in vehicle configurations with a
Extend screed which cannot be extended.

vehicle!
- To retract the left half of the screed
42
Left screed A This function is not used in vehicle configurations with a
Retract screed which cannot be extended.

vehicle!
- To retract the right half of the screed
43
Right screed A This function is not used in vehicle configurations with a
Retract screed which cannot be extended.

vehicle!
D 11 21
44
45
47
46
D 11 22
- To manually trigger the conveying function for the left
half of the auger, conveying direction outwards.
Left auger
"MANUAL"
44
conveying direction A For manual triggering, the auger function must be
switched to "AUTO" or "MANUAL"
outwards
A On manual triggering, the automatic function is overrid-

den with reduced delivery capacity.
- To manually trigger the conveying function for the
right half of the auger, conveying direction outwards.
Right auger
"MANUAL"
45
outwards

- To manually trigger the conveying function for the left
half of the auger, conveying direction inwards.
Left auger
"MANUAL"
46
inwards

- To manually trigger the conveying function for the
right half of the auger, conveying direction inwards.
Right auger
"MANUAL"
47
inwards

D 11 23
48
49
51
50
D 11 24

- The conveying function of the left conveyor is
switched on when the drive lever is swivelled out and
is continuously controlled via the material limit switch-
es in the material tunnel.
Left conveyor
48
"AUTO" A The function is shut off by pressing the EMERGENCY
STOP button or restarting the vehicle.
A The main function switch locks the conveying function.

vehicle!

- The conveying function of the right conveyor is
Right conveyor
49

vehicle!
D 11 25
48
49
51
50
D 11 26

- The conveying function of the left conveyor is
switched on continuously with full delivery capacity,
without material control via the limit switches in the
material tunnel.
- Switch OFF by pressing the button again.
- Reverse conveyor: Keep button pressed for approx.

1 second. The main function switch (62) must be
Left conveyor switched to "OFF" in this case.
"MANUAL" /
50
reverse
A To avoid excessive conveying, the system is shut off at
conveyor (o) a defined material height!
A The function is shut off by pressing the EMERGENCY


vehicle!

- The conveying function of the right conveyor is
without material control via the limit switches in the
material tunnel.
- Reverse conveyor: Keep button pressed for approx.

1 second. The main function switch (62) must be
Right conveyor switched to "OFF" in this case.
"MANUAL" /
51
reverse
A To avoid excessive conveying, the system is shut off at
conveyor (o) a defined material height!


vehicle!
D 11 27
52
53
55
54
D 11 28

- The conveying function of the left half of the auger is
es.
Left auger
52

vehicle!

- The conveying function of the right half of the auger is
Right auger
53

vehicle!
D 11 29
52
53
55
54
D 11 30

- The conveying function of the left half of the auger is
without material control via the limit switches.
Left auger
54
"MANUAL" A The function is shut off by pressing the EMERGENCY

vehicle!

- The conveying function of the right half of the auger is
without material control via the limit switches.
Right auger
55
"MANUAL" A The function is shut off by pressing the EMERGENCY

vehicle!
D 11 31
58
56
59
61
57
60
D 11 32

- For manual actuation of the levelling cylinders when
the automatic levelling system is switched off.
A The corresponding switch on the remote control must

56 Adjustment be switched to "Manual" for this function.
Levelling cylinder
A Levelling cylinder adjustment is carried out with the ad-
justment buttons in the displayed arrow direction.
A This function is also activated when the remote control

is not connected!

- For hydraulic adjustment of the auger height.
A The height can be read on the scales to the left and the
right of the auger crossbeam support.
Auger Rule of thumb: Paving thickness plus 5 cm (2 inches)
57 equals the auger crossbeam height.
Lift/lower (o)
A Actuate both relevant adjustment switches at the same

time as the auger crossbeam otherwise jams!
A Auger adjustment is carried out with the adjustment but-

tons in the displayed arrow direction!
D 11 33
58
56
59
61
57
60
D 11 34
- To adjust the selected function in the corresponding
Adjustment button:
58 direction.
Retract / lift on left
vehicle!
- To adjust the selected function in the corresponding
Adjustment button:
59 direction.
Retract / lift on right
vehicle!
Adjustment button: - To adjust the selected function in the corresponding
60 Extend / lower on direction.
left
vehicle!
Adjustment button: - To adjust the selected function in the corresponding
61 Extend / lower on direction.
right
vehicle!
D 11 35
62
63
D 11 36
- To lock all functions relevant to paving. Despite "Au-
to" settings in the individual functions, these are not
activated when the drive lever is swivelled out.
Main function - Switch OFF by pressing the button again.
62
switch
A The preset vehicle can be relocated and released at the
new paving location. The paving process is continued
on swivelling the drive lever out.
A On restarting, the function is set to "ON".

Button with detent switch function and LED feedback
A The main function switch must be set to the OFF posi-

tion.
- Button function: Keep the button pressed for longer

than 1.5 seconds (LED ON). The screed is lowered as
long as the button is pressed. When the button is re-
leased, the screed is held in the stop paving + relief
pressure position. (LED ON).
m Screed may lower slowly!
- Resting function: Press the button briefly (LED ON) -

the screed is lowered. Press the button briefly again -
Stop paving +
the screed is stopped.
relief pressure
- Screed floating position: Pressing the button switches
63 /
the LED ON and the screed is in readiness in the
lower screed +
"floating position", which is activated via the swivelled
floating position
out drive lever.
- Switch off by pressing the button again or via the lift
screed button.
A During paving, the screed always remains in its floating

position. During intermediate stops (drive lever in centre
position), the screed is switched to stop paving + relief
pressure.
m Check whether the screed transport safeguard is insert-

ed!

vehicle!
D 11 37
64
65
D 11 38
- Filling function for the paving process.
The diesel engine's speed is increased to the preselect-
ed nominal speed and all conveying functions set to "Au-
tomatic" (conveyor and auger) are engaged.
A The main function switch must be set to the OFF po-

sition.
Fill vehicle for paving
64
process - Switch OFF by pressing the button again or by swiv-
elling the drive lever out to the paving position.
- On reaching the adjusted material height (material
sensor), the filling function is automatically switched
off.
f On actuation, note danger zones of moving parts of

the vehicle!
- When the vehicle is stationary, this function enables
all operating functions, which can only be activated
when the drive lever is swivelled out (vehicle driv-
ing), to be started up.
65 Set-up mode
A The main function switch must be set to the OFF po-
sition.
A The engine speed is increased to the preselected

nominal value.
D 11 39
66 68 70 72 74
67 69 71 73 75
D 11 40

- Tamper ON and OFF function.
- Activation is carried out by swivelling the drive lever
out.
Tamper - Switch OFF by pressing the button again.
66
(screed-specific)
tion.
A The function is preset in conjunction with the "Set-up

mode" button.

- Vibration ON and OFF function.
out.
Vibration - Switch OFF by pressing the button again.
67
(screed-specific)
tion.

mode" button.

- For lifting the screed (LED ON) for switching off the
"Screed floating position" function
68 Lift screed m Check whether the screed transport safeguard is insert-
ed!

vehicle!

- Function for switching the auxiliary compactor ON
and OFF.
out.
Auxiliary
69 compactor - Switch OFF by pressing the button again.
(screed-specific)
tion.

mode" button.
D 11 41
66 68 70 72 74
67 69 71 73 75
D 11 42

- For relieving the screed to influence the traction force
and compaction ratio.
70 Screed relieving - Switch OFF by pressing the button again or switching
between screed relieving and screed charging.
- To preset the hydraulic oil pressure, switch this button and
the "Set-up mode" button to "ON".

- For relieving the screed to influence the traction force
and compaction ratio.
71 Screed charging - Switch OFF by pressing the button again or switching
between screed relieving and screed charging.
- To preset the hydraulic oil pressure, switch this button and
the "Set-up mode" button to "ON".
D 11 43
66 68 70 72 74
67 69 71 73 75
D 11 44
Buttons with detent switch function and LED feedback:

- To preselect the speed level -
Travel drive transport speed
72
fast (hare)
A On restarting, the speed is set to operating speed
(tortoise).
Buttons with detent switch function and LED feedback:

- To preselect the speed level -
Travel drive operating speed.
73
slow (tortoise)
A On restarting, the buttons are set to operating speed
(tortoise).

- Normal position for straight-ahead travel.
Straight-ahead A On restarting, the "Straight-ahead travel" button is set.

74
travel
A If the "Turning on the spot" function has been inadvert-
ently activated (and the steering is set to straight-ahead
travel), the paver finisher does not move. This is often
interpreted as a "malfunction".

- The vehicle turns on the spot (the caterpillar chains
run in opposite directions) when the steering is set
to "10".
- Steering turned to the left = vehicle turns to the left
- Steering turned to the right = vehicle turns to the right
A The function can only be activated in the "travel drive

slow" speed.
75 Turning on the spot
A If the "Turning on the spot" function has been inadvert-

ently activated (and the steering is set to straight-ahead
travel), the paver finisher does not move. This is often
interpreted as a "malfunction".
f When the vehicle turns, persons and objects next to the

paver finisher are in extreme danger. Monitor the area
where the paver finisher turns!
D 11 45
76 77 78 79 80 81 82
STOP
83 84 85 86 87 88 89
D 11 46
76 not used
77 not used
Lights up when a serious error has occurred on the engine.

m Switch off the drive engine immediately!
Error message
78 "Serious error" A The error code can be called up using the switch
"Call up error / malfunction".
(red)
A Lights up for a few seconds once the ignition has been

switched on for checking purposes.
Lights up when the engine temperature is too high.

m The engine performance will be throttled down automat-
ically. (Driving mode remains possible). Stop the paver
finisher (drive lever to the centre position), let the engine
Indicator lamp cool down while idling. Determine the cause and rectify
79 Engine coolant if necessary (refer to "Malfunctions" section). After cool-
temperature ing down to normal temperature, the engine will run with
full performance again.
A Indicates the fault together with the "Error message"

lamp.
Indicator lamp Lights up when the hydraulic filter needs replacing.

80
hydraulic filter A Replace filter element acc. to Maintenance Instructions!
81 not used
82 not used
D 11 47
76 77 78 79 80 81 82
STOP
83 84 85 86 87 88 89
D 11 48
Battery charge in- Must go out after starting when the engine revs up.
83
dicator (red) - If the light does not go out, switch off the engine
84 not used
Indicates that there is a drive engine fault. Depending on the

type of fault, the vehicle can temporarily continue to be operat-
ed or, in the case of serious faults, should be shut down imme-
diately to prevent further damage from occurring.
Error message Each fault should be rectified as soon as possible!
85
(yellow)
A The error code can be called up using the switch
"Call up error / malfunction".
A Lights up for a few seconds once the ignition has been

switched on for checking purposes.
m Lights up when the oil pressure is too low.

Switch off the engine immediately!
Oil pressure indica- For further possible faults, see Engine operating in-
86 tor lamp for the die- structions.
sel engine (red)
A Indicates the fault together with the "Error message"
lamp.
Must go out right after the engine has been started. Observe
warm running. The hydraulic oil is possibly too cold and stiff.
87
Oil pressure indica-
tor for the hydraulic
m Do not switch on the travel drive when the lamp does
not go out (see the section "Malfunctions").
travel drive (red)
A The lamp goes out when the pressure drops below
2.8 bar = 40 psi.
88 not used
89 not used
D 11 49
2.2 Special functions
Reversible conveyor
D 11 50
The conveyor's direction can be reversed in order to slightly reverse any paving ma-
terial which may be positioned just in front of the auger. This enables e.g. material
losses to be avoided during transportation.
- Switch the main function switch (1) to the "off" position (LED off).
- Keep one or both buttons (2) depressed for approx. 1 second.
The conveyor moves a distance of approx. 1 metre towards the hopper.
A If necessary, this process can be repeated as often as required to allow the conveyor
to run further in the reverse direction.
D 11 51
A B B A
D 11 52
3 Remote control
A Depending on the side of the vehicle, the button blocks (A) and (B) are assigned to
either the auger or the conveyor control system. The relevant element which is con-
trolled is indicated by an illuminated symbol (C).
m Important! Do not disconnect remote controls during operation!

This causes the paver finisher to be shut down!
D 11 53
120
121
D 11 54
In the case of an emergency (danger to persons, possible col-

lision, etc.), press in the button!
- Pressing the emergency stop button switches the engine,
the drives and the steering system off.
Making way, lifting the screed or other actions are then no
Emergency stop
120 longer possible! Danger of accidents!
button
- The emergency stop button does not shut off the gas heat-
er system.
Close the main shut-off valve and the valves on the bottles
by hand!
- To restart the engine, the button must be pulled out again.
Connect the plug to the screed.

Remote control
121
connection cable A Whether this involves the left-hand or the right-hand re-
mote control is automatically detected.
D 11 55
122 123
124
125
D 11 56

- The conveying function of the corresponding half of
the auger is switched on continuously with full deliv-
ery capacity, without material control via the limit
switches.
Auger
122 - Switch OFF by pressing the button again
"MANUAL"

the auger is switched on when the drive lever is swiv-
elled out and is continuously controlled via the mate-
rial limit switches.
Auger - Switch OFF by pressing the button again
123
"AUTO"
A The main function switch (operating panel) locks the

conveying function.
- The auger's conveying direction can be reversed in
order to slightly reverse any paving material which
may be positioned just in front of the auger. This en-
ables e.g. material losses to be avoided during trans-
portation.
Auger - Temporally limited reversal is carried out when the
124
"Reversing mode" button is pressed continuously.
A The auger function must be switched to "AUTO" or

"MANUAL" for reversing mode.
A In reversing mode, the automatic function is overridden

with reduced capacity.
D 11 57
122 123
124
125
D 11 58
- Plus/minus buttons for adjusting the delivery
capacity.
Auger delivery - The delivery capacity is slowed down or speeded up
125 depending on the length of time for which the button
capacity
is pressed.
A For adjustment purposes, the auger function

must be switched to "AUTO" or "MANUAL".
D 11 59
126 127
128
129
D 11 60

the conveyor is switched on continuously with full de-
livery capacity, without material control via the limit
switches.
Conveyor - Switch OFF by pressing the button again
126
"MANUAL"
A The main function switch locks the

conveying function.

the conveyor is switched on when the drive lever is
swivelled out and is continuously controlled via the
material limit switches.
Conveyor - Switch OFF by pressing the button again
127
"AUTO"
A The main function switch (operating panel) locks the

conveying function.
- The conveying direction of the corresponding half of
the conveyor can be reversed in order to slightly re-
verse e.g. paving material which may be present in
the material tunnel.
Conveyor - Temporally limited reversal is carried out when the
128 button is pressed continuously.
"Reversing mode"
A The conveyor function must be switched to "AUTO" or
"MANUAL" for reversing mode.
A In reversing mode, the automatic function is overridden

with reduced capacity.
D 11 61
126 127
128
129
D 11 62
- Plus/minus buttons for adjusting the delivery capaci-
ty.
Conveyor - The delivery capacity is slowed down or speeded up
129 depending on the length of time for which the button
delivery capacity
is pressed.
A For adjustment purposes, the conveyor function

must be switched to "AUTO" or "MANUAL".
D 11 63
131
132
133
130
D 11 64

Operating mode - Operating mode "AUTO" (LED ON):
levelling levelling engages automatically when the drive lever
130 "AUTO" / is swivelled out for paving operation.
"MANUAL"
- Operating mode "MANUAL" (LED OFF):
left
levelling switched off.
- To retract and extend the levelling cylinder on the cor-
responding side of the vehicle.
131 Adjustment A On adjustment, note the levelling display in the remote
control display!
/ Left levelling
132 cylinder
A For direct adjustment, the levelling function must be set
to "MANUAL".
In "AUTO" operating mode, adjustment is carried out af-
ter confirming the enter button (133).
- For confirming levelling cylinder adjustment in "Auto"
133 Enter operating mode.
Levelling cylinder adjustment is carried out by press-
ing the button.
D 11 65
135
136
137
134
D 11 66

Operating mode - Operating mode "AUTO" (LED ON):
levelling levelling engages automatically when the drive lever
134 "AUTO" / is swivelled out for paving operation.
"MANUAL"
- Operating mode "MANUAL" (LED OFF):
right
levelling switched off.
- To retract and extend the levelling cylinder on the cor-
responding side of the vehicle.
135
Adjustment A On adjustment, note the levelling display in the remote
Right levelling control display!
/
cylinder
136
A For direct adjustment, the levelling function must be set
to "MANUAL".
In "AUTO" operating mode, adjustment is carried out af-
ter confirming the enter button (137).
- For confirming levelling cylinder adjustment in "Auto"
137 Enter operating mode.
Levelling cylinder adjustment is carried out by press-
ing the button.
D 11 67
138
140 140
139
D 11 68
- For manual actuation of the levelling cylinders on the
corresponding side of the vehicle when the
Levelling cylinder
138 automatic levelling system is switched off (LED OFF).
manual
A On adjustment, note the levelling display in the remote

control display!
- To retract and extend the screed half on the corre-
sponding side of the vehicle.
Screed
139 Retract/extend A This function is not used in vehicle configurations with a
screed which cannot be extended.

vehicle!
Press in the case of emergencies and to indicate when the ve-

hicle starts to move!
140 Horn
A The horn can also be used to communicate acoustically
with the truck driver for material loading!
D 11 69
D 11 70
D 20 Operation
1 Operation of the input and display terminal
H
A
F
I
G
Button layout on the display
- (A) encoder (rotary actuation):

- To scroll in the menu
- To select various parameters within a menu
- To change parameters
- (B) - (G) function buttons:

- To trigger the commands assigned in the display area (H)
- To select the menus assigned in the display area (I)
D 20 1
Command symbols
Command Symbol in the display
- Call up sub-menu /
call-up parameter for adjustment
- Save setting /
acknowledge the display
- Exit menu
- Cancel
Menu range
- The menu range is shown in area (I) of the display. The menus upstream and down-
stream of the currently shown menu item are displayed.
A The centrally positioned symbol (J) indicates the currently displayed menu.
D 20 2
1.1 Menu operation
D 20 3
Example: Conveyor / auger capacity (menu 7 / sub-menu 700)
- Turn the encoder (A) until the desired menu appears.

- Press button (B) to call up the set-up menu.
- Turn the encoder (A) again until the selection field (red frame) is positioned over
the desired parameter to be adjusted.
- Press button (B) to activate the selected parameter to be adjusted.
- Set the desired parameter by turning the encoder (A).
- Press button (F) to exit parameter adjustment without saving.
- Press button (B) to confirm the set value.
- Press button (G) to exit the setting menu.
A The set-up menus stored in various menus can be called up directly by pressing the
relevant function button.
D 20 4
Menu structure of the setting and display options
The following illustration shows the menu structure and serves to simplify operation
and the procedure in the case of various settings and displays.
D 20 5
Main menu
A
Display and function menu
B
Displays:
4 C
- (1) speed: 3 D
2
- paving operation (m/min) 5 E
1 10
- driving mode (km/h)
F
- (2) engine speed (rpm) 7
8 6 G
- (3) fuel gauge 9
- (4) engine
coolant temperature (°C)
- (5) engine oil pressure
(bar)
- (6) on-board voltage (V)
- (7) distance travelled counter (m)
- (8) actual temperature of screed heating(°C)
- (9) time of day (hh/mm)
Functions:
A The functions are activated or deactivated by pressing the adjacent function

button. If the relevant symbol is covered with a red cross, the function is deactivated.
- (C): drive engine "eco mode"

- The engine speed is constantly regulated to 1600 rpm.
- (D): automatic steering unit

- The vehicle is steered automatically via corresponding
sensing along a reference (e.g. cable).
m When the automatic steering unit is activated, the steering potentiometer is deactivat-
ed.
A If the driver carries out a steering movement, this overrides the automatic steering
unit due to safety reasons.
- (E): delayed screed start

- On swivelling the drive lever, the screed functions are only activated once the time
set in the relevant menu has elapsed.
D 20 6
- (F): camera display
- The vehicle positions monitored by camera are shown in the display
- Direct jump to display menu 13 - camera display
- (G): diesel engine speed

- Direct jump to set-up menu 101 - diesel engine speed
A Depending on operating status, different symbols are shown at position (10):

Hare: Transportation gear active
Tortoise: Working gear active
STOP: Machine stop
20km/h Important! Machine speed too high! Reduce travel!
Snow flake: hydraulic oil temperature too low! Let machine run up to temperature with
stationary acceleration!
A The engine speed cannot be increased when the hydraulic oil temperature is too low!
Hare with wheels: Trailer (o) connected.
A When the trailer (o) is connected, all screed, auger and levelling functions are lo-
cked, apart from lifting/lowering screed.
D 20 7
Menu 01 -
diesel engine speed
Menu for setting the

engine speed.
Set-up menu 101 -

diesel engine speed
- (1) nominal speed display

and adjustment parame-
ters
1
- (2) actual speed display
A Adjustment is carried out in

steps of 50; the engine speed
is adapted directly. 2
D 20 8
Menu 02 -
drive engine measured
values
Menu for querying various

drive engine measured val-
ues.
Sub-menu 201 -
drive engine measured
value display
Display of the following

1
measured values:
2
- (1) on-board voltage (V)
- (2) engine 3
coolant temperature (°C) 4

- (3) engine oil pressure
(bar)
- (4) operating hours (h)
D 20 9
Menu 03 -
paving distance
Menu for retrieving and reset-

ting the current paving area
and for activating and deacti-
vating the automatic steering
unit and for displaying the
steering monitoring.
Sub-menu 301 -
displaying, resetting
paving distance /
automatic steering
unit ON/OFF,
steering monitoring
C
1
- (1) current paving distance
- Reset - set value to zero: E
button (C). 2
- (2) steering monitoring is

used for distance control
scanning --> reference.
- automatic steering unit
ON/OFF: button (E).
A Ideal distance scanning --> reference is the value "0" in display (2). Excursions indi-
cate increased or reduced distances.
A If necessary, carry out correction via slight steering movement!
A If the driver carries out a steering movement, this overrides the automatic steering
unit due to safety reasons.
D 20 10
Menu 04 -
external levelling
Manu for preselecting the lev-

elling system which is used.
A If work is to be carried out

with an external levelling sys-
tem, corresponding changeo-
ver must be carried out.
Setting menu 401 -

external levelling
- (1) left levelling display and

adjustment parameters
- (2) right levelling display
1 2
ters
- Internal levelling: 3
parameter 0
- External levelling:
parameter 1
A When "External levelling" is

selected, the toggle switches
of the system's own remote
control remain active!
Only for pavers with wheel drive:
- (3) advance display and adjustment parameters with front wheel drive switched on.
A Additional traction power is made available by a increased speed of the front wheels.
The distance difference as a result of the advance is reduced by slip.
D 20 11
Menu 05 -
paving thickness
Menu for setting the type of

course to be laid.
Set-up menu 501 -

paving thickness
preselection
Preselection of the following

course types:
C
- (1) course type display and
adjustment parameters.
- foundation: 1
parameter 1
- binder course:
parameter 2
- wearing course:
parameter 3
m On switching to a different
type of course, the screed parameters in setting menu 600 are automatically switched
to the values last set up for the corresponding type of course!
- (C): Delayed tamper start

- When the drive lever is deflected, the tamper function is only activated once the
time set in the relevant menu has elapsed.
D 20 12
Menu 06 -
screed parameters
Menu for setting various

screed parameters: B
- (B): compacting element C

frequencies - D
setting menu 600
E
- (C): delayed screed start -
setting menu 601
- (D): screed type selection -
setting menu 602
- (E): screed heater system
temperature preselection -
setting menu 603
D 20 13
Setting menu 600 -
compacting element
frequencies
Menu for setting the compac-

tor frequencies:
1
- (1) nominal tamper number
of revs. (RPM) display 2
ters 3
- (2) nominal vibration
number of revs. (RPM) dis-
play and adjustment pa-
rameters
- (3) nominal auxiliary com-
pactor number of revs.
(RPM) display and adjustment parameters
A Tamper, vibration and auxiliary compactor adjustment range depending on screed
type. (Follow screed manual)
m On switching to a different type of course in set-up menu 501, the screed parameters
are automatically switched to the values last set up for the corresponding type of
course!
Setting menu 601 -

delayed screed start

screed starting delay:
- (1) delay duration (sec.)

display and adjustment pa-
rameters
A On swivelling the drive lever, 1

the floating function of the
screed is only activated once
the set time has elapsed.
A Setting range 0-60 sec.
D 20 14
Setting menu 602 -
screed type selection

screed type.
- (1) screed type display and

1
adjustment parameters
- screed type Vario (V):
parameter 1
- screed type Rigid (R): 2
parameter 2
- (2) Heating type display
ters
- Electric heater:
parameter 1
- Gas heater: parameter 2
A If a different screed type has been connected to the paver finisher, the corresponding
setting must be carried out!
Setting menu 603 -

screed heater system
Menu for setting the screed

heater system:
- (1) nominal screed heater

system temperature (°C) 1
display and adjustment pa-
rameters 6
- (2) actual temperature, 2 3

left-hand main screed (°C) 4 5
- (3) actual temperature,

right-hand main
screed (°C)
- (4) actual temperature,
left-hand extendable part + extension parts (°C)
- (5) actual temperature, right-hand extendable part + extension parts (°C)
A Setting range 0-180°C
A All changes will be taken over to the other input devices (remote control, control box
of screed heating).
Only when equipped with E-heating:
- (6) Number of actual heatet screed sections

D 20 15
Menu 07 -
conveyor / auger capacity
Menu for setting the conveyor

and auger capacity.
Set-up menu 700 -

conveyor / auger capacity
- (1) nominal left-hand con-

veyor capacity (%) display
1 3
ters
- (2) actual left-hand 2 4
conveyor capacity
display (%) 5 7
- (3) nominal right-hand con-
veyor capacity (%) display 6 8

ters
- (4) actual right-hand
conveyor capacity display
(%)
- (5) nominal left-hand auger capacity (%) display and adjustment parameters
- (6) actual left-hand auger capacity (%)
- (7) nominal right-hand auger capacity (%) display and adjustment parameters
- (8) actual right-hand auger capacity (%)
A Setting range 0-100%
D 20 16
Menu 08 -
system information
Display of the following infor-

mation: 1
2
- (1) time (hh/mm/ss) 3

- (2) date (dd/mm/yyyy)
- (3) software version, 4
travel drive computer 5

- (4) software version,
terminal
- (5) operating hours (h)
A If consultation with Technical

Support is required for your
vehicle, always specify the software version!
D 20 17
Menu 09 -
service
Password-protected menu
for various service settings.
D 20 18
Menu 10 -
error memory
Menu for querying existing er-

ror messages again.
Query menu 111 -

error memory:
- (C): query menu,

"Active errors" -
display of currently present
error messages. C
1
- (F): query menu, "Error his-
tory" - display of all previ-
ously occurred error
F
messages.
2
A The number of stored errors

is displayed at positions (1) /
(2).
D 20 19
Error display
A The display "Attention" is al-

ways shown first prior to each
error message. B
The error message is dis-
played by pressing the button
(B).
A All error messages can be

identified in the section "Ter-
minal error displays".
A If consultation with Technical

Support is required for your
vehicle, always specify the
number (1) of the error mes-
sage!
D 20 20
Menu 11 -
terminal settings
Menu for various

terminal settings.
Setting menu 110 -

terminal settings
- (1) button daytime bright-

ness (%) display
ters
- (2) button night time bright- 1 2
ness (%) display E

ters
3
A Setting range 0-100%
A When the working lights are

switched on, the system auto-
matically switches to the night
time operation settings.
- (3) "beep" display and adjustment parameters - warning signal for error messages
until the error has been acknowledged.
- "beep" ON:
parameter 1
- "beep" OFF:
parameter 0
A Press button (E) to call up the system menu.
D 20 21
System menu -
Basic settings
Display
- (1) Language display and

adjustment parameters 1
2
- (2) Time display and ad- 3
4
justment parameters (hh- 5
mm) E
- (3) Date display and adjust-
ment parameters
(DD-MM-YYYY)
- (4) Monitor brightness dis-
play and adjustment pa-
rameters
- (5) Button brightness dis-
play and adjustment parameters
A The display brightness is adjusted directly, the buttons light up briefly to check.
D 20 22
Menu 12 -
button function test
Menu for testing the function

of the operating panel but-
tons.
Test menu 120 -

button function test
On pressing the individual

buttons, the relevant button
symbol is shown to confirm
the function.
A The function test can only be

carried out when the drive en-
gine is not running.
An error message is pro-
duced if the engine is run-
ning.
D 20 23
Menu 13 -
camera display
(camera 2)
Menu for displaying the cam- B

era images - camera 1 (o).
C
- show camera 2 display:
button (B).
- show camera 1+2 dis-
play: button (C).
Menu 13b -
camera display
(camera 1)

era images - camera 2 (o).
C
button (B).
- show camera 1+2
display: button (C).
Menu 13c -
camera display
(camera 1+2)

era images - camera 1+2 (o).
C
button (B).
button (C).
D 20 24
2 Terminal error messages
A Every error message is assigned a number. If consultation with Technical Support is

required for your vehicle, specify this number, together with all other visible informa-
tion relating to the error message!
Error No. / meaning Display
Error message 102

Fan control valve
Error message 103

Emergency stop button
actuated
or
communication
display master
Error message 104

Communication
engine electronics master
D 20 25
Error message 105

Communication
operating panel keyboard
master
Error message 106

Communication
remote control master
Variable:
- left remote control (1)
- right remote control (2)
1 2
Error message 107

- Error - drive lever
D 20 26
Error message 108

- Error - drive unit sensor
Variable:
- left sensor (1)
- right sensor (2) 1 2
Error message 109

- Battery voltage too low
Error message 110

- Conveyor drive valves
Variable:
- left conveyor drive (1) 1 2
- right conveyor drive (2)

- reverse left
conveyor (3) 3 4
- reverse right
conveyor (4)
D 20 27
Error message 111

- Auger drive valves
Variable:
- left auger drive (1) 1 2
- right auger drive (2)

- Reverse left
auger (3) 3 4
- Reverse right
auger (4)
Error message 112

- Auger lift valves
Variable: 1 2
- lift left auger (1)

- lift right auger (2)
- lower left auger (3) 3 4
- lower right auger (4)
Error message 113

- Tamper / vibration drive
valves
Variable:
- tamper drive (1)
- vibration drive (2) 1 2
D 20 28
Error message 114

- Pump distribution gear /
engine separating clutch
valves
Variable:
- separating clutch valve (1) 1 2
- separating clutch valve (2)
Error message 115

- Drive unit brake valve
Error message 116

- Error - tank sensor
D 20 29
Error message 117

- Auger material sensors
Variable:
- left sensor (1)
- right sensor (2) 1 2
Error message 118

- Communication
master-slave
Error message 119

- Error - steering angle sensor
D 20 30
Error message 120

- Error - central lubrication
system relay
Error message 121

- Error - road speed potenti-
ometer
Error message 122

- Levelling valves
Variable:
- Levelling
Lift left (1) 1 2
- Levelling
Lift right (2)
- Levelling 3 4
Lower left (3)
- Levelling
Lower right (4)
D 20 31
Error message 123

- CAN error
electric screed heating sys-
tem
Variable:
- main screed, left (1)
- extendable part, left (3)
- main screed, right (2)
- extendable part, right (4)
Error message 124

- Conveyor limit switches
Variable:
- Left limit switch
(paddle) (1)
- Right limit switch
(paddle) (2) 1 2
- Left limit switch 3 4
(ultrasound) (3)
- Right limit switch
(ultrasound) (4)
Error message 125

- Screed extending/retracting
valves 1 2
Variable:
- extend right screed (1)
- retract left screed (2)
- retract right screed (3) 3 4
- extend left screed (4)
D 20 32
Error message 126

- Error - steering potentiome-
ter
Error message 127

- Screed lifting / lowering
valves
Variable:
- Screed 1 2
lift/lower left (1)
- Screed
3 5
lift/lower right (2) 4
- floating position pressure
valve (3), (4)
- screed non-return valve (5)
Error message 128

- Open / close hopper / front
hopper valves
Variable: 3 4
- open left hopper (1) 5
- open right hopper (2)
- close left hopper (3) 6
1 2
- close right hopper (4)
- close front hopper (5)
- open front hopper (6)
D 20 33
Error message 130

- Calibration not carried out or
completed
Variable:
- pump flows (1)
- potentiometer (2) 1 2
Error message 131

- Error - system check
Internal error in the master
Error message 132

- Parameter error
Wrong machine type select-
ed
D 20 34
Error message 133

- Valves, movement of opera-
tor's platform
Variable:
- move operator's platform
to the left (1)
- move operator's platform 1 2
to the right (2)
Error message 134

- Error - hazard warning flash-
ers
Error message 135

- Error - rotary beacon
D 20 35
Error message 136

- Error - travel drive
Pump or engine failure
Error message 137

- "drivelimp" Drive controll dis-
turbance
A Driving mode limited in
the event of an error
Error message 138

- System error
D 20 36
Error message 139

- Error: brake pedal
f Machine must not be
operated any more!
Error message 140

- Battery voltage too high
D 20 37
Error message 141

Communication
Display master
Error message 142

- Data error
Data missing for
- alternator
- oil temperature
- service hours
- Engine speed
Error message 143

Remote control
Variable:
- Left remote control (1)
- Right remote control (2) 1 2
D 20 38
Error message 144

- Conductor break valve or
temperature sensor hydrau-
lic / data missing for engine
charge air.
Error message 145

Contamination indicator air fil-
ter
A Proceed with air filter
maintenance!
Error message 146

Retarder valves
Variable:
- Left valve (1)
- Right valve (2) 1 2
D 20 39
Error message 147

Valves front axle
Error message 149

Start inhibit
A Drive lever must be in
neutral position when
starting!
Error message 150

- Error - system check
Internal error in the master
D 20 40
Error message 151

- Power supply master
Error message 152

- Error: braking light
Error message 153

- Auger ultrasound sensors
Variable:
- Left sensor (1)
- Right sensor (2)
D 20 41
Error message 155

- Valve function lock
or
- Faulty travel drive
preselection when "trailer"
function active.
A The transport gear can-
not be selected if the
trailer is not connected!
Error message 156

- Valves "safe impact system"
Variable:
- Extend push roller
crossbar (1)
- Retract push roller 1 2
crossbar (2)
Error message 157

- Valves screed lock
Variable:
- Extend screed lock (1)
- Retract screed lock (2) 1 2
D 20 42
Error message 158

- Valves crowning adjuster
Variable:
- Extend crowning (1)
- Retract crowning (2) 1 2
Error message 159

- Valves auxiliary compactor
Variable:
- Lift auxiliary
compactor (1)
- Lower auxiliary
1 2 3
compactor (2)
- Activate auxiliary
compactor (3)
Error message 160

- Error extraction
D 20 43
2.1 Drive engine error codes
If a fault has been detected on the drive

engine, this is indicated by the corre- 2
sponding warning lamp (1) / (2) and si-
multaneously appears in code on the STOP
display.
The error message simultaneously

shown on the display contains several 3
numerical codes, which uniquely define
the fault after decoding.
- "ENGINE WARNING!" display (3) indi-

cates that there is a fault on the drive
engine. The vehicle can continue to be
operated on a temporary basis. How-
ever, the fault should be remedied
quickly to prevent further damage.
- "STOP ENGINE!" display (4) indicates
a serious fault on the drive engine, in
which the engine is stopped or has to
be stopped immediately to prevent fur- 4
ther damage.
D 20 44
Example:
STOP
Explanation:
Warning light and display signal a serious fault on the drive engine with automatic or
necessary engine shut-down.
Display:
SPN: 157
FMI: 3
OC: 1
Cause: Cable break on sensor for rail pressure.

Effect: Engine shut-down.
Frequency: Fault occurs for the 1st time.
m Notify customer service of the error number displayed on your paver finisher; the cus-
tomer service department will then discuss the further procedure with you.
D 20 45
2.2 Error codes
D 20 46
D 20 47
D 20 48
D 20 49
D 20 50
D 20 51
D 20 52
D 30 Operation
1 Operating elements on the paver finisher
1.1 Control elements on the operator's control station
Protective roof (o)

4
The protective roof can be raised and
lowered with a manual hydraulic pump.
A The exhaust pipe is lowered or raised to-

gether with the roof.
3
- Remove the lower section of the pump
lever (1) from the storage compart-
ment, and connect to the upper sec-
tion using a pipe (2).
- Lower the roof: The locks (3) on both
sides of the roof must be released.#
5
- Raise the roof: The locks (4) on both
sides of the roof must be released. 2
- Set the adjustment lever (5) to the
"Raise" or "Lower" position.
- Raise the roof: The lever points for- 1
wards.
- Lower the roof: The lever points
backwards.
- Operate the pump lever (1) until the roof has reached the upper or lower limit posi-
tion.
- Roof in uppermost position: Set the locks (3) on both sides of the roof.
- Roof lowered: Set the lock (4) on both sides of the roof.
m If the vehicle is equipped with a protective roof, the engine hood must be closed be-
fore lowering the roof!
D 30 1
Protective cabin (o)
The protective roof is equipped with an

additional front window and two side
windows.
- The side windows can be swivelled

out to the side at the bracket (1).
Press the lock (2) to unlock.
Windscreen wiper 2
3
- Activate the windscreen wiper (3) /

screen wash on the operating panel if
1
necessary.
A Ensure that the washer fluid tank (4) is

always adequately filled.
m Replace worn wiper blades immediately.
D 30 2
Control panel, rigid
Operating panel, moveable
The operating panel can be shifted to several positions on the left- and right-hand
sides of the vehicle.
- Loosen panel latch (1) and slide panel console to the desired position using the
handle (2).
- Insert panel latch (1) into one of the detent positions (3).
m Make sure it is latched properly!
f Only adjust the operating position whilst the vehicle is stationary!
D 30 3
Control platform, moveable (o)
2
7
The control platform can be hydraulically shifted beyond the left/right outer edge of
the vehicle, providing the driver with a better view of the paving area in this position.
- When the control platform has been moved, the windows (1) additionally offer
a good view of the paving area.
A Refer to the operating panel for actuation of the platform movement function.
m Shifting the platform increases the basic width of the paver finisher.
f If the platform is moved, ensure that there is no one in the vehicle's danger area!
D 30 4
Operating panel, moveable
The operating panel can be shifted to several positions on the left- and right-hand
sides of the vehicle.
- Raise panel latch (2) and slide panel console to the desired position using the han-
dle (3).
- Insert panel latch (2) into one of the detent positions (4).
Operating panel, swivelling (o)
The entire operating panel can be swivelled for operation beyond the outer edge of
the vehicle.
- Press latch (5), swivel operating panel to the required position using the handle (3)
and allow latch to engage again in one of the intended detent positions.
Control platform lock (o)
f During transportation in road traffic and when transporting the vehicle on transport-
ers, the control panel must be secured in the central position!
- Remove the locking pin (7) from its storage compartment (press pushbutton) and
insert into locking aperture (8).
m To be able to set the lock, the panel must be positioned centrally above the vehicle
frame.
D 30 5
.Emergency actuation control
platform, movable
1
If the control platform cannot be moved
hydraulically, it can be pushed back to its
central position by hand. 2
- Remove the screw cap (1) (next to the

right footwell window).
- Remove screw (2).
A This undoes the connection between the

platform and the frame so that the plat-
form can be moved.
- Restore the original status after eliminating the fault.
D 30 6
Seat console, swivelling (o)
The seat consoles can be swivelled for

operation beyond the outer edge of the
vehicle.
- Press latch (1), swivel seat console to

the desired position and allow latch to
engage again.
f Only adjust the operating position whilst

the vehicle is stationary!
Seat console storage compartment
A Beneath both seat consoles, there is a

storage compartment which can be
locked (1). 1
A Lock the storage compartments at the

end of work.
D 30 7
Driver's seat, type I
9
f To avoid damage to health, the individu-
al seat settings should be checked and 10
adjusted before starting the vehicle.
6 7
f After locking the individual elements, it
must no longer be possible to shift then 6
to another position.
3 8
- Weight setting (1): The relevant driv-
er's weight should be set by turning
4 11
the weight adjustment lever when the
driver's seat is unoccupied. 5
- Weight indicator (2): The set driver's
weight can be read off at the viewing 1
window.
2
- Longitudinal adjustment (3): Longi-
seat4.tif
tudinal adjustment is released by actu-
ating the locking lever.
The locking lever must engage in the desired position.
- Seat depth adjustment (4): The seat depth can be individually adjusted. Raise the
button to adjust the seat depth. The desired position is set by simultaneously sliding
the seat surface forwards or backwards.
- Seat inclination adjustment (5): The seat surface's longitudinal inclination can be
individually adjusted. Raise the button to adjust the inclination. The seat surface in-
clines to the desired position by simultaneously loading or relieving it.
- Armrest inclination (6): The armrest's longitudinal inclination can be adjusted by
turning the hand wheel. Turning outwards raises the front of the armrest; turning
inwards lowers it at the front.
In addition, the armrests can be folded up fully.
- Lumbar support (7): Both the height and the extent of the convexity in the backrest
padding can be individually adjusted by turning the hand wheel to the left or right.
- Backrest adjustment (8): The backrest is adjusted via the locking lever. The lock-
ing lever must engage in the desired position.
- Back extension (9): By pulling out via perceptible detents, the height can be indi-
vidually adjusted up to a limit stop. To remove the back extension, the limit stop is
overcome with a jolt.
- Seat heating ON/OFF (10): The seat heating is switched on and off by actuating
the switch.
- Seat belt (11): The seat belt must be applied before starting up the vehicle.
f The seat belts must be replaced following an accident.
D 30 8
Driver's seat, type II
f To avoid damage to health, the individu-

al seat settings should be checked and
7
adjusted before starting the vehicle.

6
f After locking the individual elements, it
must no longer be possible to shift then 6
to another position. 5
3
- Weight setting (1): The relevant driv-
er's weight should be set by turning
8
the weight adjustment lever when the
driver's seat is unoccupied. 4
- Weight indicator (2): The set driver's
weight can be read off at the viewing 1
window.
- Longitudinal adjustment (3): Longi- 2
seat4.tif
tudinal adjustment is released by actu-
ating the locking lever.
The locking lever must engage in the desired position.
- Seat height adjustment (4): The seat height can be individually adjusted. Turn the
handle in the desired direction to adjust the seat height.
- Backrest adjustment (5): The backrest inclination can be continuously adjusted.
Turn the handle in the desired direction to adjust.
- Armrest inclination (6): The armrest's longitudinal inclination can be adjusted by
turning the hand wheel. Turning outwards raises the front of the armrest; turning
inwards lowers it at the front.
In addition, the armrests can be folded up fully.
- Lumbar support (7): Both the height and the extent of the convexity in the backrest
padding can be individually adjusted by turning the hand wheel to the left or right.
- Seat belt (8): The seat belt must be applied before starting up the vehicle.
f The seat belts must be replaced following an accident.
D 30 9
Fuse box
The terminal box, which contains all fus-

es and relays, etc. is located beneath the
central control platform floor panel.
A An assignment plan for fuses and relays

can be found in chapter F8.
15
10
25
10
15
15
25
15
10
15
25
15
10
15
25
15
10
10
D 30 10
Batteries
The batteries (1) of the 24 V system are

located in the vehicle footwell.
A For the specifications, refer to chapter B,

"Technical data". For maintenance, see
chapter "F".
m External starting must only be carried

out according to the instructions (see 1
section "Starting the paver finisher, ex-
ternal starting (starting aid)".
Main battery switch
The main battery switch separates the

current circuit from the battery to the
main fuse.
A For the assignment of all fuses, see

chapter F.
- To interrupt the battery's current cir-

3
cuit, turn the key pin (3) to the left and
pull it out.
A Do not lose the key pin as in this case

the paver finisher can no longer be
moved!
D 30 11
Hopper transport safeguard
Before transporting or in order to park

the paver finisher, the hopper halves
1
must be swung upwards and the trans-
port safeguards for the hopper must be
inserted on both sides of the vehicle.
- Pull the locking pin (1) and place the 2

transport safeguard (2) with the han-
dle above the hopper cylinder's piston
rod.
f Without transport safeguards inserted,

the hopper halves will slowly open; dan-
ger during transportation!
Screed lock, mechanical (o)
A The screed locks must additionally be

engaged on both sides of the vehicle pri-
or to transportation with the screed lifted. 1
f Transportation with an unsecured

screed leads to a risk of accidents!
- Lift the screed.

- On both sides of the paver finisher,
slide the screed lock beneath the
crossbeams using the lever (1); place
the lever in the detent position.
m ATTENTION!
Insert screed lock only at crown adjust-
ment "zero"!
Screed lock only for transportation!
Do not enter or work under screed only secured with screed lock for transportation!
Danger of accidents!
D 30 12
Screed lock, hydraulic (o)
A The screed locks must additionally be

extended on both sides of the vehicle
prior to transportation with the screed 1
lifted.
f Transportation with an unsecured

screed leads to a risk of accidents!
- Lift the screed.

- Activate the function on the operating
panel.
A The two screed locks (1) extend hydrau-

lically.
m ATTENTION!
Insert screed lock only at crown adjustment "zero"!
Screed lock only for transportation!
Do not enter or work under screed only secured with screed lock for transportation!
Danger of accidents!
D 30 13
Paving thickness indicator
Two scales, on which the currently set

paving thickness can be read off, are lo-
cated on the left and right sides of the
vehicle.
I
I
I
- Loosen the clamping bolt (1) to
I
change the position of the indicator.
I
A
I
In normal paving situations, the same 1
paving thickness should be set on both
sides of the vehicle!
Other displays (o) are on the

crossbeam guide.
- To change the reading position, the

scale (2) can be raised and lowered 3
again in one of the adjacent locating
bores (3).
- The pointer (4) can be swivelled to 2
different positions using the locking
knob (5).
m The scale (2) and pointer (4) must be

swivelled in completely to transport the 4
machine.
5
m Avoid parallax errors!
D 30 14
Auger lighting (o)
A Two swivelling headlights (1) are located

1
on the auger box for illuminating the au-
ger compartment.
- They are engaged together with the

working lights.
A These are activated together with the

other working lights on the operating
panel!
Engine compartment lighting (o)
A The engine compartment lighting can be

activated when the ignition is switched
on. 1
- On/off switch (1) for the engine com-

partment lighting.
D 30 15
Xenon working light (o)
f Xenon working lights have a secondary

high voltagesource.
Only a qualified electrician may work on
the lighting after the primary voltage has
been switched off.
A Please contact a Dynapac dealer!
f Caution, environmentally harmful waste!

Working lights with Xenon lamps have a
gas discharge lamp containing mercury
(Hg). A defective lamp is deemed to be
hazardous waste and must be disposed
of in accordance with the local regula-
tions.
LED working light (o)
There are two LED spotlights (1) at the

front of the machine and also at the
back.
f Always align the working lights to avoid 1

dazzling the operating personnel or
other road users!
D 30 16
500 watt spotlight (o)
There are two halogen spotlights (2) at

the front of the machine and also at the
back.
- For machine without roof: use

clamping bolt (3) to change the height 2
of the spotlights.
f Always align the working lights to avoid

dazzling the operating personnel or
other road users!
3
f Danger of burning! The working lights

get very hot!
Do not touch working lights that are
switched on or hot!
Camera (o)
There is a camera (1) at the front of the

machine and also at the back.
- The camera can be swivelled in

various directions.
A The pictures are shown in the control pa-

nel display.
D 30 17
Auger height adjustment ratchet (o)
For mechanical adjustment of the auger

height
- Set the ratchet direction lever (1) to

the clockwise or anti-clockwise direc-
tion. Turning anti-clockwise lowers the 1
auger, turning clockwise lifts the au-
ger.
- Actuate the ratchet lever (2) 2
- Set the desired height by alternatingly
actuating the left and right ratchets.
A The current height can be read on both

auger height indicators.
A Observe the notes on adjusting the auger height in the chapter "Set-up and modifica-
tion"!
Auger height indicators
A scale (1), on which the currently set

auger height can be read off, is located
on the left and right sides of the ladder. 2
A Display in cm
- Loosen the clamping bolt (2) to

change the position of the indicator.
1
m When setting the auger height, adjust-
ment must be carried out evenly on both
sides to prevent the auger from jam-
ming!
D 30 18
Sensor rod / sensor rod extension
4
8
3
2
1
7
The sensor rod acts as an orientation aid for the vehicle driver during paving.
Along the defined paving route, the vehicle driver can use the sensor rod to follow a
tensioned reference wire or another marking.
The sensor rod runs along the reference wire or over the marking. Steering deviations
can therefore be ascertained and corrected by the driver.
m Use of the sensor rod increases the basic width of the paver finisher.
f If the sensor rod or sensor rod extension are used, ensure that there is no one in the
vehicle's danger area!
A The sensor rod is adjusted when the vehicle is positioned, with its set working width,
on the paving route and the reference marking running parallel to the paving route has
been set up.
Adjusting the sensor rod:
- The sensor rod (1) is located on the face end of the vehicle and can be pulled out
to the left or right after releasing the four clamping bolts (2).
A In the case of larger working widths, the sensor rod extension (3) is inserted into the
sensor rod.
D 30 19
- Once the sensor rod has been set to the desired width, the clamping bolts (2) must
be tightened again.
- The inserted sensor rod extension is secured with the bolts (4).
A Depending on the side of the vehicle on which the sensor rod extension is used, the
entire sensor rod may have to be removed and re-inserted on the other side of the
vehicle!
- After releasing the wing nuts (5), the end section of the sensor rod extension (6)
can be set to the desired length; the angle can additionally be changed by swivel-
ling on the joint (7).
A Either the adjustable indicator or the chain can be used as an aid to orientation.
m Tighten all assembly parts properly after setting up!
A The sensor rod extension's joint (7) can be mounted on both sides of the vehicle in
position (8).
At this point, the sensor rod extension can be swivelled in for transporting the vehicle
without increasing the vehicle's basic width.
D 30 20
Manual separator fluid spray (o)
Used to spray the parts coming into con-

tact with asphalt with a separator emul-
sion.
4
- Remove the spray (1) from its bracket. 5
- Build up pressure by actuating the
2
pump lever (2).
- The pressure is indicated on the ma- 3
nometer (3).
- Actuate the manual valve (4) to spray.
- On completion of work, secure the
manual spray in its bracket with a lock
(5).
1
f Do not spray into open flame or on hot

surface! Danger of explosion!
2
D 30 21
Separator fluid spraying system (o)
Used to spray the parts coming into con-

tact with asphalt with a separator emul-
sion.
- Connect the spray hose (1) with quick- 10

action coupling (2).
Only switch on the spraying system

m when the diesel engine is running; other-
wise, the battery will be discharged.
Switch off after use.
7
A permanently installed hose package 2
A
(3) for the spraying system is available 8
as an option. 4
9
5
- Pull the hose out of the device until a
click is audible. When released, the
hose automatically engages here. The
hose is automatically retracted into the
guide after pulling and discharging
again. 6
1
- Actuate button (4) to activate and de-
activate the pump.
- The indicator lamp (5) lights up when
the emulsion pump is running.
- Actuate the manual valve (6) to spray.
9
3
Do not spray into open flame or on hot
f surface! Danger of explosion!
A The spraying system is fed by a canister

(7) at the vehicle step.
7
Refill the canister only while the vehicle

f is stationary!
8
4
9 5
- If the system is not in use, place the
spray lance (8) in the provided holder
(9).
6
- If the spray hose is not in use, it can be
placed in its bracket (10).
D 30 22
Conveyor limit switches - PLC ver-
sion
The mechanical conveyor limit switches

(1) or the ultrasonic conveyor limit
switches (2) control the material flow on
the relevant half of the conveyor. The
conveyors should stop when the materi-
al has roughly reached the area below
the auger tube.
1
A This requires that the auger height has
been adjusted correctly (see chapter E).
A In vehicles with a PLC control system,

the deactivation point is set on the re-
mote control.
D 30 23
Conveyor limit switches - conven-
tional version
The mechanical conveyor limit switches

(1) control the material flow on the rele-
vant half of the conveyor. The conveyors
should stop when the material has 2
roughly reached the area below the au- 1
ger tube.
A This requires that the auger height has

been adjusted correctly (see chapter E).
- To set the deactivation point, release

the two mounting screws (2) and set
the switch to the required height.
- After adjusting, retighten all mounting
parts properly.
D 30 24
Ultrasonic auger limit switches (left
and right) - PLC version
A The limit switches control the material

flow at the relevant half of the auger
without contact. 1
The ultrasonic sensor (1) is secured to 3

the side shield via a bracket (2).
2
- To adjust, release the clamping lever /
stop screw (3) and adjust the sensor's
angle. 4
parts properly.
A The connection cables (4) are connected to the relevant sockets on the remote con-
trol bracket.
A The sensors should be adjusted so that 2/3 of the augers are covered with the paving
material.
A The paving material must be conveyed over the full working width.
A We recommend adjusting the limit switch positions during material distribution.
A In vehicles with a PLC control system, the deactivation point is set on the remote con-
trol.
D 30 25
Ultrasonic auger limit switches (left
and right) - conventional version
A The limit switches control the material

flow at the relevant half of the auger
without contact.
The ultrasonic sensor (1) is secured to 3

the side shield via a bracket (2). 2
4
- To adjust the sensor angle, loosen the
clamps (3) and swivel the bracket.
- To set the sensor height / the deacti-
vation point, loosen the star handles
(4) and adjust the linkage to the re-
1
quired length.
parts properly.
A The connection cables are connected to

the relevant sockets on the remote con-
trol bracket.
A The sensors should be adjusted so that

2/3 of the augers are covered with the
paving material.
D 30 26
24 volt / 12 volt sockets (o)
A socket (1) is located beneath the left/

right seat consoles.
Additional working lights can be con-
nected here, for example. 1
- Right seat console: 12V socket

- Left seat console: 24V socket
A Voltage is present when the main switch

is switched on.
D 30 27
Pressure control valve for screed
charging/relieving
A valve (1) is used to set the pressure for

additional screed charging/relieving. 3 1
2
A Switching on, see screed charging/re-
lieving (chapter "Operating panel", "Op- 20 400
200
600
CN 837
800
1000
1200 80
20
1400
psi
eration"). 0
bar
100
- For pressure indication, see manome-

ter (3).
Pressure control valve for paving

stop with relieving
This is used to set the pressure for "Screed control with paver finisher stop - floating
stop with relieving".
- Switching on, see screed stop / paving stop

(Chapters "Operating panel", "Operation").
- For pressure indication, see manometer (3).
Manometer for screed charging/relieving
The manometer (3) indicates the pressure for:
- Screed charging/relieving when the drive lever is in the third position (pressure set-
ting with valve (1)).
D 30 28
Central lubrication system (o)
The central lubrication system is activat-

ed in automatic mode as soon as the
drive engine is started.
- Pumping time: 4 min

- Pause time: 2 h
m It is prohibited to change the factory-set

durations of pumping and break without
consulting the technical customer serv-
ice!
A Changing the duration of lubrication and

breaks may be necessary when laying
mineral or cement bound material mix.
D 30 29
Lane clearer (o)
A swivelling lane clearer (1), which de-

flects small obstacles away to one side,
is located in front of both drive units.
A The lane clearers should only be swiv-

elled down during paving.
1 2
Swivelling the lane clearers:
- Swivel the lane clearer (1) up and se-

cure in the uppermost position with a
shackle (2). 4
- To lower the lane clearer, it must be 3
lifted a little and the shackle (2) must 5mm
be swivelled back.
LW_2009A.bmp
m To avoid collisions, the lane clearer must

be adjusted so that a few mm are available between the ground and the blade (3).
A The blade's level above the ground is adjusted with a bolt (4).
D 30 30
Screed eccentric adjustment
3
To pave thicker layers of material, if the
piston rods in the levelling cylinder are
operating close to their limit position and
if the desired paving thickness cannot be
reached, it is possible to alter the ap- III II
proach angle of the screed by adjusting 4 I
the eccentric.
- Pos. I: Paving thickness up

to approx. 7 cm
2
- Pos. II Paving thickness of approx.
7 cm to approx. 14 cm
1
- Pos. III Paving thickness above
approx. 14 cm
- The spindle (1) is not adjusted.

- Unfasten locks (2) for eccentric adjustment.
- Swivel screed to the desired position using the lever (3), and engage the locking
knob again.
A If the levelling unit is connected to a height controller, this has the function of balanc-
ing out any rapid rise in the screed position: The levelling cylinders are extended until
the correct height is reached.
- The change in approach angle can only take place slowly and uniformly on both
sides at once during paving operation, and involves the use of eccentric adjust-
ments. Failing this, any rapid response in the screed could easily cause waves to
appear on the road surface.
The setting process should therefore take place before work starts!
A When equipped with rigid screed, the second hole (4) is intended for (item I).
D 30 31
adjustable
For adaptation to various truck design

types, the push roller crossbar (1) can be
shifted to two positions.
A The adjustment travel is 90 mm.

2
- Close the hopper halves to lift the hop-
per flap (2).
- After removing the bolts (4), remove
the locking plate (3) on the lower side
of the crossbar. 6
- Remove insert plate (5).
- Move the push roller crossbar to stop
to the front / rear position. 1
A Shift the push roller crossbar at the tow-

ing eye (6) or use a suitable assembly le- 3
ver in its guide (left and right) to push it 4
into the corresponding position.
4
- Turn the insert plate (5) 180° and rein- 3
sert into the groove in the front or rear
position.
- Properly reinstall the locking plate (3)
with bolts (4).
D 30 32
hydraulically extendable (o) (o)
For adaptation to various truck design

types, the push roller crossbar (1) can be
retracted and extended hydraulically.
A The max. adjustment travel is 90 mm.

panel as necessary. 1
m Extending the push roller increases the

transportation length of the paver finish-
er.
f On actuation, ensure that nobody is in

the danger area!
Push roller damping,

hydraulic (o)
A Push roller damping hydraulically absorbs the shocks between the material truck and
paver finisher.
- Activate the function on the operating panel as necessary.
D 30 33
Storage box
2
A For storing the on-board tool kit, remote
controls and other accessories.
1
A Lock the storage box at the end of work.
Fire extinguisher (o)
A The paver finisher personnel must be fa-

miliarised with fire extinguisher (2) oper-
ation.
A Observe the inspection intervals for the

fire extinguisher!
D 30 34
Rotary beacon (o)
(o)
m The function of the rotary beacon must

be checked daily before starting work. 2
1
- Place the rotary beacon onto the plug-
in contact and secure with a wing
bolt (1).
- Slide the rotary beacon with the tube
(2) out to the desired height and se- 3
cure with the clamping bolt (3).
- Vehicle version with protective roof:
Raise the bracket (4), swivel to the 2
outer position and allow to engage 1
there.
panel as necessary.
2
A The rotary beacon is easy to remove and
should be stored securely at the end of
work.
D 30 35
Fuelling pump (o)
(o)
m The fuelling pump must only be used to

pump diesel fuel.
m Foreign bodies which are larger than the

mesh size of the intake cage (1) lead to
damage. An intake cage must therefore
always be used.
4
m Each time fuelling is carried out, the in-

take cage (1) must be checked for dam-
age, and must be replaced if damaged. 1
Do not work without it under any circum-
2 3
stances, as the fuelling pump is not oth-
erwise protected against foreign bodies.
- Insert the suction hose (2) into the container which is to be emptied.
A To enable the container to be emptied completely, the suction hose must reach down
to the floor of the container.
- Activate the function on the operating panel as necessary.
m The fuelling pump does not shut off automatically. Therefore, never leave the pump
unattended when fuelling!
m Never operate the pump without pumping a fluid. The risk of damaging your diesel
pump is run if it runs dry.
- To end fuelling, switch the function "off" on the operating panel.

- Place the end of the hose, with the intake cage, into its cup (3) so that no diesel is
able to escape into the environment.
- Gather up the hose and place it over the bracket (4).
D 30 36
Power moon (o)
The power moon is a special, illuminated 2

balloon with shadow-reducing and anti- 1
dazzle light.
f Use of the power moon increases the

height of the paver finisher.
f Note the passage height of bridges and

tunnels.
f The power moon must not be used in the

vicinity of highly flammable materials
(e.g. petrol and gas); a safety distance of
at least 1 metre must be maintained from
combustible materials.
f A safety distance of at least 50 m must

be maintained from high-voltage lines,
and at least 2.5 m from railway track volt-
age lines.
f The power moon must not be operated if

the electric supply cables or connectors
are damaged.
- Hold the handle (1) tightly and pull the

detent pin (2) out.
- Press the handle down until the detent
pin engages.
m Before starting up, check whether the

Velcro seal around the power moon is
closed. If the skin is damaged, it must be
repaired or replaced. The bulbs must be
checked for firm seating and damage.
D 30 37
- Secure the lower part of the tripod (3)
to the preassembled bracket (5) using
the relevant assembly parts (4). 8
- Connect the tripod sections (6) and
secure with stop screws (7).
- Place the power moon's journal (8)
onto the top part of the tripod and se- 9
cure with the stop screws (9).
- Finally, place the assembled tripod 6
sections, together with the power
moon, onto the lower part of the tripod 7
(3) and secure with the stop screws
(10). 6
- When the power moon has been fully
10
assembled and secured, the power 5
moon connector (11) can be connect- 3
ed to its current supply.
- The power moon is switched off by re-
moving the power connector (11) from
the socket. 11
m On assembly, make sure that the lower

part of the tripod projects max. 15 cm out
4
of the bracket. Risk of collision!
15cm
D 30 38
D 41 Operation
1 Preparing for operation
Required devices and aids
To avoid delays on site, check before starting work whether or not the following
devices and aids are present:
- Wheel loader for transporting heavy extension parts

- Diesel fuel
- Engine oil and hydraulic oil, lubricants
- Separator fluids (emulsion) and manual injector
- Two filled propane gas bottles
- Shovel and broom
- Scraper (spatula) for cleaning the auger and the hopper infeed area
- Parts that may become necessary for extending the auger
- Parts that may become necessary for extending the screed
- Percentage spirit level + levelling rail, 4 m long
- Levelling wire
- Protective clothing, signal vest, gloves, ear protection
D 41 1
Before starting work
(in the morning or when starting paving)
- Heed the safety instructions.

- Check the personal protective equipment .
- Take an inspection walk around the paver finisher and check for leaks and
damages.
- Install parts removed for transportation or for the night.
- When screed is operated with the optional gas heating system, open the closing
valves and the main shut-off valve.
- Perform the check according to the "Checklist for the vehicle operator" given below.
Check list for the vehicle operator
Check! How?
Emergency stop button Push in the button.

- on the operating panel The diesel engine and all running drives
- on both remote controls must stop immediately.
The paver finisher must immediately fol-

low every steering wheel movement in a
Steering
precise manner. Check straight ahead
travel.
Horn
Briefly press the horn button.
- on the operating panel
Horn signal must sound.
- on both remote controls
Switch on with the ignition key, walk

Lights around the paver finisher to check and
switch off again.
With the ignition switched on, press the

Screed hazard flasher switches for extending/retracting the
(with vario screeds) screed parts.
Hazard warning flashers must flash.
Gas heater system (o): Check:

- Bottle holders - Secure seat
- Bottle valves - Cleanliness and tightness
- Pressure reducer - Working pressure 1.5 bar
- Hose break safety devices - Function
- Shut-off valves - Function
- Main shut-off valve - Function
- Connections - Tightness
- Indicator lamps of the switch box - All indicator lamps must light up when
the system is switched on
D 41 2
Check! How?
For larger working widths, the walkway

Auger coverings plates must be extended and the auger
tunnels must be covered.
For larger working widths, the walkway

plates must be extended.
Hinged walkway plates must be swung
Screed covers and walkways down.
Check that the side shields, the side
plates and the covers are securely
seated.
When the screed is lifted, it must be pos-

Screed transport safeguard sible to push the retaining pins beneath
the crossbeams.
When the hopper is closed, it must be

Hopper transport safeguard possible to swivel the safeguards over
the hopper cylinders.
Protective roof The locking bolts must be set properly.
Other facilities:
Check that the hoods and flaps are
- Engine panels
securely seated.
- Lateral flaps
Equipment must be present on the vehi-

Accessories: cle!
- First aid box A Always observe the local
regulations!
D 41 3
10
12
13
15
11
120
D 41 4
1.1 Starting the paver finisher
Before starting the paver finisher
Before starting the diesel engine and beginning operation, the following steps must
be performed:
- Daily maintenance of the paver finisher (see chapter F).
m Check the operating hours counter to determine whether further maintenance work
should be conducted.
- Check the safety devices and protective devices.
"Normal" starting
- Set the drive lever (13) to the centre position and the travel drive preselector (15) to
minimum.
- Insert the ignition key (11) in position "0".
m The lights should be switched off during starting to reduce the current drain on the
battery.
A It is impossible to start the vehicle, if one of the emergency stop buttons (10) / (120)
is depressed.
(Error shown on the display)
- Press the starter button (12) to start the engine. Do not let the starter run perma-
nently for more than 30 seconds; allow for a break of 2 minutes after every attempt!
D 41 5
10
12
13
15
11
120
D 41 6
External starting (starting aid)
A The engine can be started with the help of an external power source if the batteries
are empty and the starter no longer turns.
Suitable power sources are:
- Other vehicles with a 24 V system

- Additional 24 V battery
- Start device that is suitable for external starting (24 V/90 A).
m Standard chargers or quick chargers cannot be used for external starting.
To externally start the engine:
- Switch on the ignition (11), set the drive lever (13) to the centre position and the
travel drive preselector (15) to minimum.
- Use appropriate cables to connect the external power source.
m Observe the polarity! Always connect the negative cable last and disconnect it first!
A It is impossible to start the vehicle, if one of the emergency stop buttons (10) / (120)
is depressed.
(Error shown on the display)
- Press the starter button (12) to start the engine. Do not let the starter run perma-
nently for more than 30 seconds; allow for a break of 2 minutes after every attempt!
When the engine is running:
- Disconnect the power source
D 41 7
65
13
D 41 8
After starting
To increase the engine speed:
- Press button (65) to increase engine speed.
A The engine speed is increased to the preset value.
m Let the paver finisher warm up for approx. 5 minutes if the engine is cold.
D 41 9
13
76 77 78 79 80 81 82
STOP
83 84 85 86 87 88 89
D 41 10
Observe indicator lamps
The following indicator lamps must be observed under all circumstances:
For further possible faults, see Engine operating instructions.
Engine coolant temperature check (79)
Lights up when the engine temperature is outside of the permissible range.
m Stop the paver finisher (drive lever to the centre position), let the engine cool down
while idling.
Determine the cause and correct it if necessary.
A The engine performance will be throttled down automatically. (Driving mode remains
possible).
After cooling down to normal temperature, the engine will run with full performance
again.
Battery charge indicator (83)
Must go out after starting when the engine revs up.
m If the lamp does not go out or lights up during operation: Briefly rev up the engine.
Switch off the engine and determine the fault if the lamp does not go out.
For further possible malfunctions, refer to the section "Malfunctions".
Oil pressure indicator lamp for the diesel engine (86)
Must go out at the latest 15 seconds after starting.
m If the lamp does not go out or lights up during operation: switch off engine immediately
and determine fault.
D 41 11
65
54 55
50 51
76 77 78 79 80 81 82
STOP
83 84 85 86 87 88 89
D 41 12
Oil pressure indicator lamp for the travel drive (87)
- Must go out after starting.
m If the lamp does not go out:

Do not switch on the travel drive! Otherwise, the entire hydraulic system could be
damaged.
When the hydraulic oil is cold:
- Activate set-up mode function (65).

- Set the conveyor function (50)/(51) to "manual" and the auger function (54)/(55) to
"manual". Conveyor and auger start to operate
- Let the hydraulics warm up until the indicator lamp goes out.
A The Lamp goes out when the pressure drops below

2.8 bar = 40 psi.
For further possible faults, refer to the section "Malfunctions".
D 41 13
68
56 58 59
65
13
42 43
36 37
15
16
126 130
D 41 14
1.2 Preparation for transportation
- Close the hopper with switch (36)/(37).

- Engage both hopper transport safeguards.
- Lift the screed completely using switch (68), set the crossbeam lock.
- Turn the travel drive preselector (15) to zero.
- Activate set-up mode function (65).
- Fully extend the levelling cylinders with switch (56),(58)/(59).
A To extend the levelling cylinders, levelling operating mode (126)/(130) must be

switched to "MANUAL" (LED OFF) on the remote controls.
- Use switch (42)/(43) to adjust the screed to the basic width of the paver finisher.
m Lift the auger if necessary!
A The drive is locked by an engine start with drive lever out of center position.
To start the drive, the lever must be put into center position before.
D 41 15
72 10
13
2
15
16
D 41 16
Driving and stopping the paver finisher
- Set the fast/slow switch (72) to "Hare".

- Set the preselector (15) to mark 10.
- For driving, carefully tilt the drive lever (13) forward or backward according
to the drive direction desired.
- Use the preselector (15) to regulate the speed.
- Carry out steering movements by actuating the steering potentiometer (16).
f In case of an emergency, press the emergency stop button (10)!
- To stop, set the preselector (15) to "0" and move the drive lever (13) into its centre
position.
D 41 17
1.3 Preparations for paving
Separator fluid
Spray the parts coming into contact with

asphalt (hopper, screed, auger, push
roller) with a separator fluid.
Do not use diesel fuel as it dissolves the

bitumen.
Screed heater system
Switch on the screed heater approx. 15–30 minutes (depending on the ambient tem-
perature) before paving begins. Warming up prevents the material from sticking to the
screed plates.
D 41 18
Direction marks
To ensure straight paving, a direction

mark must be present or established
(road edge, chalk lines or similar).
- Slide the operating panel to the de-

sired side and secure it.
- Pull the direction indicator out of the
bumper (arrow) and adjust it accord-
ingly.
D 41 19
64
62
54 55
50 51
36 37
A B
D 41 20
Loading/conveying material
- Button (62) has to be switched off.

- Use switch (36)/(37) to open the hopper.
Instruct the truck driver to dump the material.
- Set the switches for the auger (54)/(55) and the conveyor (50)/(51) to "Auto".
- Activate function (64) to fill the vehicle for the paving process.
- Switch the conveyors on.

The conveyor limit switches (A) / (B) must switch off when the material has approx-
imately reached the area beneath the auger crossbeam.
- Check that the material is transferred properly.
Manually switch on or off the conveyor if the material is not conveyed properly until
a sufficient amount of material lies in front of the screed.
D 41 21
73
66
67
63
52 53
48 49
13
15
126 130 126 130

123
127
D 41 22
1.4 Starting for paving
Set the switches, levers and controls listed below to the specified positions when the
screed has reached its operating temperature and a sufficient amount of material lies
in front of the screed:
Item Travelling direction Position

13 Drive lever Centre position
73 Travel drive fast/slow Tortoise-operating speed
15 Travel drive preselector Mark 6-7
Preparation for screed floating posi-
63 LED ON
tion
67 Vibration LED ON
66 Tamper LED ON
52/53
Auger left/right Auto
123
48/49
Conveyor left/right Auto
127
126 /
Levelling Auto
130
Speed regulation, vibration Depending on the working conditions
Speed regulation, tamper Depending on the working conditions
- Push the drive lever (13) all the way to the front and start driving.
- Observe the distribution of the material and adjust the limit switches if necessary.
- Set the compacting elements (tamper / vibration) according to the required com-
paction ratio.
- Let the paving master check the paving thickness after 5–6 meters and correct if
necessary.
Carry out the check in the area of the caterpillar chains or drive wheels as the screed
tends to level an uneven ground. The reference points for the layer thickness are the
caterpillar chains or drive wheels.
The basic setting of the screed must be corrected when the actual layer thickness de-
viates significantly from the values indicated by the scales (see the operating instruc-
tions for the screed).
A The basic setting is for asphalt material.
D 41 23
1.5 Checks during paving
The following points must be constantly observed during paving:
Paver function
- Screed heater system

- Tamper and vibration
- Engine oil and hydraulic oil temperature
- The screed parts must be retracted and extended in time when obstacles are in the
way
- Uniform material transport and distribution or supply to the screed; may require cor-
rections to settings of the material switches for conveyor and auger.
A See the section "Malfunctions" when paver finisher functions fail.
Quality of the layer
- Paving height
- Slope
- Evenness in the driving direction and at right angles to it
(check with 4 m levelling rod)
- Surface structure/texture behind the screed.
A See section "Malfunctions, problems during paving" if the paving quality is poor.
D 41 24
1.6 Paving with "screed control at paving stop" and "screed charging/relieving"
General
The screed hydraulics can be influenced in three different ways to attain optimum
paving results:
- Paving stop + relief when the paver finisher is halting,

- floating paving when the paver finisher is driving,
- floating paving with screed charging or relieving when the paver finisher is driving.
A Relieving reduces the screed weight and increases the traction force.
Charging increases the screed weight, reduces the traction force, but increases the
compaction ratio. (To be used with light-weight screeds in exceptional cases.)
D 41 25
13
15
68 70
63
71
D 41 26
Screed charging/relieving
This function charges or relieves the screed regardless of its own dead weight.
Function (70) Relieving (screed "lighter")

Function (71) Charging (screed "heavier")
A The "Screed charging and relieving" functions are only effective when the paver fin-
isher moves. According to the activated function, the paver finisher is automatically
switched to "paving stop + relief" when stationary.
Screed control with paver finisher stop / in paving operation

(screed stop / paving stop / floating paving)
Button (63) can be used to activate the following functions:
- Screed stop / floating position (OFF)-->(LED OFF)

- Screed is hydraulically held in position.
A Function for setting up the paver finisher and for lifting/lowering the screed
- Paving stop / floating paving (ON)-->(LED ON)
The following functions are active depending on operating status:
- "Paving stop": when the paver finisher is stationary.

The screed is held by the relief pressure and the counter pressure of the material.
- "Floating paving": during paving operation.
Lower screed to the floating position with preselected screed charging/relieving
function.
A Function for paving operation.
- To lift the screed press switch (68).

- To lower the screed:
- Resting function: Keep button (63) pressed for longer than 1.5 seconds. The
screed is lowered as long as the button is pressed. When the button is released,
the screed is stopped again.
- Button function: Press button (63) briefly - the screed is lowered. Press the button
briefly again - the screed is stopped.
As in the case of screed charging and relieving, a pressure of 2-50 bar is separately
applied to the screed lifting cylinders. This pressure acts to combat the weight of the
screed to prevent the screed from sinking into the freshly laid material, thus support-
ing the paving stop function, especially when the screed relieving function is used.
D 41 27
The pressure to be applied depends on the load-bearing capacity of the material. If
necessary, the pressure must be readjusted or changed as required during the first
stops until the lower edge of the screed no longer leaves any marks when the finisher
moves on again.
A pressure greater than 10-15 bar neutralises the screed weight, thus preventing the
screed from sinking into the material.
A When combining the "paving stop" and "screed relieving" functions, make sure that
the pressure difference between the two functions does not exceed 10–15 bar.
m Especially in those cases where the "screed relieving" function is only briefly used as
a start-up aid, there is a danger of uncontrolled floating when starting up again.
D 41 28
D 41 29
13
15
70
63
71
D 41 30
Adjusting the pressure
Pressure adjustments can only be made while the diesel engine is running. There-
fore:
- Start the diesel engine and turn the traction controller

(15) back to zero (precaution against inadvertent advancing).
- Activate the "floating position" using switch (63).
For screed charging/relieving:
- Set the drive lever (13) to the centre

position. A
- Activate the screed relieving (70) or
screed charging (71) function (LED B
ON). 600 800
20 400
CN 837 1000
200 80
- Set the pressure using pressure regu- 0
psi
bar
20
1400
1200
100
lating valve (A); read it off at the ma-

nometer (B).
C
A When screed charging/relieving is nec-
essary and automatic levelling is used
(grade control and/or slope control), the
compacting performance changes (layer
thickness).
A The pressure can also be set or corrected during paving.

(Max. 50 bar)
Setting pressure for screed control with paving stop + relieving:
- Set the drive lever (13) to the centre position.

- Activate the "floating position" (63) function (LED ON).
- Set the pressure using pressure regulating valve (C); read it off at the
manometer (A).
(Basic setting: 20 bar)
D 41 31
13
15
11
D 41 32
1.7 Interrupting/terminating operation
During breaks (e.g. the material supply truck is late)
- Determine the approximate duration.

- When cooling down of the material below the minimum paving temperature
must be expected, run the paver finisher empty and create an edge like the
end of a layer.
- Set the drive lever (13) to the centre position.
During longer breaks(e.g. lunch break)
- Drive lever (13) into centre position, RPM speed adjustment (15) to minimum posi-
tion.
- Switch off the ignition (11).
- Switch the screed heater system off.
- With a screed with gas heating system (o), close the bottle valves.
A The screed must be heated up to the correct paving temperature before paving may
be restarted.
D 41 33
68
13
15
11
D 41 34
When work is finished
- Run the paver finisher empty and stop it.

- Lift the screed using switch (68), set the crossbeam lock.
- Retract the screed parts to the basic screed width and lift the auger. Where appli-
cable, completely extend the levelling cylinders.
- Close hopper halves, set hopper transport safeguards.
A The screed is hydraulically secured in the lifted position.
- While operating the tampers at a low speed, let any material residues drop out.
- Set the drive lever (13) to the centre position and the speed adjuster (15) to
minimum.
- Switch the screed heater system off.
- Switch off the ignition (11).
- With a screed with gas heating system (o), close the main shut-off valves and the
bottle valves.
- Remove the levelling units and stow them away in the boxes, close all flaps.
- Remove all parts that extend beyond the paver finisher contour or secure them if
the paver finisher is to be transported over public roads on a low-bed trailer.
- Read and check the operating hour meter to determine whether maintenance work
must be performed (see chapter F).
- Cover and lock the operating panel.
- Remove material residues from the screed and the paver finisher and spray all
parts with separator fluid.
D 41 35
2 Malfunctions
2.1 Problems during paving
Problem Reason
- change in the material temperature, demixing
- wrong material composition
- incorrect operation of the roller
- incorrectly prepared foundation
- long standstill times between loads
- grade control reference line is not suitable
- grade control jumps to the reference line
- grade control toggles between up and down
Wavy surface
(inertia setting is too high)
("short waves")
- bottom plates of the screed are loose
- bottom plates of the screed are warped or not uniformly
worn
- screed is not operated in the floating position
- too much play in the mechanical screed link/suspension
- paver finisher speed is too high
- augers are overloaded
- changing material pressure against the screed
- change in the material temperature
- demixing
- roller has stopped on the hot material
- roller has turned or roller speed has been changed too fast
- incorrect operation of the roller
- truck brake is applied too tight
- long standstill times between loads
Wavy surface
- grade control reference line is not suitable
(“long waves”)
- incorrect installation of the grade control
- limit switch is not correctly set
- screed is empty
- screed has not been switched to the floating position
- too much play in the mechanical screed link
- auger is set too deep
- auger is overloaded
- material temperature is too low
- moisture on the foundation
Cracks in the layer - demixing
(over the entire - wrong material composition
width) - wrong layer height for maximum grain size
- cold screed
- bottom plates of the screed are worn or warped
D 41 36
Problem Reason
- material temperature
Cracks in the layer - cold screed
(centre strip) - bottom plates are worn or warped
- wrong crowning
- screed extendable parts are incorrectly installed
Cracks in the layer - limit switch is not correctly set
(outer strip) - cold screed
- bottom plates are worn or warped
- moisture on the foundation
- demixing
- wrong material composition
- wrong layer height for maximum grain size
Layer composition is - long standstill times between loads
not uniform - vibration is too slow
- screed extendable parts are incorrectly installed
- cold screed
- bottom plates are worn or warped
- screed is not operated in the floating position
- auger is overloaded
- truck hits too much against the finisher while aligning to the
finisher
Marks in the surface - too much play in the mechanical screed link/suspension
- truck brake is applied
- vibration is too high while standing on a spot
Screed does not - wrong layer height for maximum grain size
react to corrective - incorrect installation of the grade control
measures as - vibration is too slow
expected - screed is not operated in the floating position
- too much play in the mechanical screed link
D 41 37
2.2 Malfunctions on the paver finisher or screed
Malfunction Reason Remedy

See operating instructions for the
At the diesel engine Various
engine
See "External starting" (start
Diesel engine does Batteries empty
assistance)
not start
Various see "Towing"
Tamper is obstructed by cold
Properly heat the screed
bitumen
Hydraulic oil level in the tank
Top up the oil
is too low
Tamper or Pressure limiting valve is Replace the valve; if necessary,
vibration is not func- defective repair and adjust the valve
tioning Seal or replace the connections
Leak in the suction line of the
pump Tighten or replace the hose
clamps
Clean the filter; if necessary,
Oil filter is soiled
replace the filter
Hydraulic oil level in the tank
Top up the oil
is too low
Check fuses and cables; replace if
Power supply interrupted
necessary
Switch is defective Replace the switch
Conveyor or One of the pressure limiting
Repair or exchange the valves
augers valves is defective
run too slowly Pump shaft broken Replace the pump
Limit switch does not switch Check the switch; replace and
or regulate correctly adjust the switch if necessary
Check the high pressure filter for
Pump is defective
dirt particles; replace if necessary
Oil filter is soiled Replace the filter
Engine speed is too low Increase the speed
Hydraulic oil level is too low Top up the oil
Leak in the suction line Tighten the connections
Flow rate regulator defective Replace
Hopper cannot be
swung open Leaking seals of the hydraulic
Replace
cylinder
Control valve is defective Replace
Check fuse and cables; replace if
necessary
D 41 38
Control valve is defective Replace
Hoppers lowers inad-
vertently Leaking seals of the hydrau-
Replace
lic cylinder
Oil pressure too low Increase the oil pressure
Leaking seal Replace
Screed cannot be Screed relieving or charging Switch must be in the centre
lifted is switched on position
necessary
Switch on the remote con-
Set the switch to "Manual"
trol is set to "Auto"
necessary
Switch on the operating
Crossbeams cannot panel defective Replace
be lifted or lowered
Excess pressure valve
Replace
defective
Flow rate regulator defec-
Replace
tive
Seals defective Replace
Control valves defective Replace
Crossbeams lower Pilot-controlled non-return
Replace
inadvertently valves defective
Seals defective Replace
D 41 39
Replace (fuse strip on the oper-
Travel drive fuse defective
ating panel)
Check potentiometer, cables,
connectors; replace if necessary
Travel drive monitoring
Replace
(type-specific) defective
Traction does not Electro-hydraulic servo unit
Replace the servo unit
work of the pump defective
Check and adjust if necessary
Insufficient supply pressure Check the suction filter; replace

the supply pump and the filter if
necessary
Drive shaft of hydraulic
Replace pump or engine
pumps or engines broken
Check the fuel level; refill fuel if
Fuel level too low
necessary
Irregular engine
speed, Fuse "engine speed control" Replace (fuse strip on the oper-
engine stop function defective ating panel)
does not work Electrical power defect Check potentiometer, cables,
(line break or short circuit) connectors; replace if necessary
D 41 40
E 11 Set-up and modification
1 Special notes on safety
f Danger to personnel by inadvertent starting of the engine, travel drive, conveyor, au-
ger, screed or screed lifting devices.
Unless otherwise specified, work may only be performed when the engine is at a
standstill!
- To protect the paver finisher against inadvertent starting:

Move drive lever into centre position and turn preselector controller to zero, remove
ignition key and battery main switch.
- Protect lifted vehicle parts (e.g. screed or hopper) against lowering by means of
mechanical safeguards.
- Replace parts or have them replaced as stipulated.
f When connecting or disconnecting hydraulic hoses and when working on the hydrau-
lic system, hot hydraulic fluid may spurt out at high pressure.
Switch off the engine and depressurise the hydraulic system! Protect your eyes!
- Mount all protective devices before re-commissioning the paver finisher.

- The walkway must always reach over the entire working width of the screed.
The hinged walkway plate may only be folded up under the following conditions:
- When paving next to a wall or a similar obstacle.
- During transportation on a low-bed trailer.
E 11 1
2 Distribution auger
2.1 Height adjustment

1
Depending on the mix of materials, the
set height of the distribution auger (1) –
measured from its bottom edge – should
lie above the material layer height.
Grain sizes up to 16 mm
Example:
Paving thickness 10 cm F0130_A1.TIF
Min. height setting 15 cm
from the ground
Grain sizes > 16 mm
Example:
Paving thickness 10 cm
Min. height setting 18 cm
from the ground
A An incorrect height setting can result in the following problems during paving:
- Auger too high:

Too much material in front of the screed; material overflow. When operating with
larger working widths, demixing and traction problems may occur.
- Auger too low:
Not enough material that can be precompacted by the auger. Irregularities resulting
from this cannot be completely compensated by the screed (wavy surface).
In addition, increased auger segment wear occurs.
E 11 2
2.2 Mechanical adjustment
with ratchet (o)
- Set the ratchet direction lever (1) to

the clockwise or anti-clockwise direc-
tion. Turning anti-clockwise lowers the
auger, turning clockwise lifts the au-
ger. 1
- Set the desired height by alternatingly
adjusting the right-hand and the left-
hand side.
- The current height can be read at the
scale (2).
2.3 Hydraulic adjustment (o)
- Determine the currently set height of

the auger crossbeam - left and right on
the scale (2).
m Actuate both of the corresponding func-

tion buttons on the operating panel
evenly to prevent the auger crossbeam
from jamming.
2
- Check whether the heights on the left
and on the right are identical.
E 11 3
2.4 Height adjustment for large working widths / with brace
1 2
3
5
4
Auger height adjustment for large working widths can be carried out with a hinged
brace:
m Only adjust the height of the auger with the slewing bracket retaining pins removed!
- Remove the slewing bracket (3) split pin (1) and retaining pin (2) on both sides of
the vehicle.
- Push the slewing brackets with braces from the attaching point on the material
shaft.
- Carry out height adjustment.
- Push the slewing brackets with braces onto the attaching point on the material
shaft.
- Install the split pin (1) and retaining pin (2) again.
A If the retaining pins (2) cannot be inserted in the new position, the braces must be
extended or shortened by rotating the adjustment rods until a continuous bore ena-
bles the retaining pin (2) to be inserted.
- Loosen lock nuts (4).
A The adjustment rods (5) are each equipped with a bore. A suitable drift can be used
to adjust the length of the adjustment rod here.
E 11 4
- Extend or shorten the braces by rotating the adjustment rods (5) until the retaining
pins can be inserted.
- Retighten the lock nuts (4).
- Install the split pin (1) and retaining pin (2).
m Each time the height is adjusted, the auger must be realigned via the braces!
A See section "Aligning the auger"!
m In the case of large working widths with double braces, the procedure must be carried
out on both pairs of braces (6) / (7)!
7 6
E 11 5
3 Auger extension
Auger_DEM.bmp
Depending on the type of screed, the most diversified working widths can be reached.
A Auger and screed extension must match.

Refer to the appropriate chapter "Set-up and modification" in the Operating instruc-
tions for the screed:
– screed extension chart
To attain the desired working width, the respective screed extensions, side plates, au-
gers, tunnel plates or cut-off shoes must be mounted.
For working widths of more than 3.00 m, the auger should be fitted with extension
parts on both sides to improve material distribution and to reduce the wear.
f The diesel engine must be switched off whenever work is performed on the auger.
Danger of injuries!
A If the operating conditions on the construction site permit an auger extension to be

fitted, or render this necessary, always additionally fit the outer auger bearings.
For auger width extensions with an outer auger bearing on the basic unit, fit the short-
er auger blade to the bearing. Otherwise, destruction between the auger blade and
bearing may occur.
E 11 6
3.1 Mounting extension parts
Mounting the material shaft and auger extension
1
3
- Secure the additional material shaft (1) to the basic unit or the adjacent material
shaft with the relevant assembly parts (2) (bolts, washers, nuts).
- Dismantle the assembly parts (3) of the adjacent auger blade, remove plug (4).
- Insert the auger shaft extension into the auger shaft.
- Reinstall the previously removed assembly parts (3) and simultaneously tighten the
auger shaft bolts.
- Insert the plug (4) at the end of the auger.
A Depending on the operating width, the outer auger bearing and/or auger end bearing
must be installed:
E 11 7
Mounting the outer auger bearing
2
1
3
7
6
- Insert the outer auger bearing (3) into the auger extension.
- Secure the outer auger bearing to the brace shaft with the relevant assembly parts
(4) (bolts, washers, pins).
A If necessary, insert fitted plates (5)!
- Reinstall the previously removed assembly parts (1) and simultaneously tighten the
auger shaft and bearing shaft bolts.
- Mount the auger half (5) on the outer side of the bearing with the relevant assembly
parts (6) (bolts, washers, nuts).
E 11 8
Mounting the auger end bearing
4
2
1
7
5
6
3
- The auger end bearing must first be pre-assembled:

- Mount the auger end bearing (1) together with the fitted plate (2) on the interme-
diate plate (4) with the relevant assembly parts (3) (bolt, washer).
- Insert the auger end bearing (7) into the auger extension.
- Secure the auger end bearing to the material shaft with the relevant assembly parts
(8) (bolts, washers, nuts).
- Reinstall the previously removed assembly parts (5) of the auger blade and simul-
taneously tighten the auger shaft and bearing shaft bolts.
E 11 9
3.2 Auger extension chart
Symbol Meaning
- Auger blade 160 mm
- (160L)
left
160L 160R - Auger blade 160 mm
- (160R)
right
- Auger extension part 320 mm
- (320L)
left
320L 320R - Auger extension part 320 mm
- (320R)
right
- (640L)
right
- (640R)
right
- (960L)
left
- (960R)
right
- Material shaft
- (320)
320 mm
320
- Material shaft
- (640)
640 mm
640
- Material shaft
- (960)
960 mm
960
- Material shaft 960 mm with

- (960BL)
brace left
960BL 960BR
- Material shaft 960 mm with
- (960BR)
brace right
E 11 10
Symbol Meaning
Outer auger bearing
Auger end bearing
E 11 11
Auger upgrading, working width 3.14 m
320 320
320 L 320 R
640 640
640 L 640 R
320 640 640 320
320 L 640 L 640 R 320 R
E 11 12
320 960 960 320
320 L 960 L 960 R 320 R
640 960 960 640
640 L 960 L 960 R 640 R
E 11 13
E 11 14
m m
960 BL 960
960 960 BR
160 L
160R
640 L 960 L
960 R 640 R
m m
320 960 BL 960 960 960 BR 320
160 L 160R
320 L 640 L 960 L 960 R 640 R 320 R
E 11 15
E 11 16
m m
640 960 BL 960

960 960 BR 640
160 L
160R
640 L 640 L 960 L

960 R 640 R 640 R
m m
320 640 960 BL 960 960 BR 640 320

960
160 L
160R
320 L 640 L 640 L 960 L 640 R 320 R

960 R 640 R
E 11 17
E 11 18
m m
640 640 960 BL 960 960 BR 640 640

960
160 L 160R
640 L 640 L 640 L 960 L 640 R 640 R

960 R 640 R
m m
640 960 960 BR 960 640

960 960 BL 960
160 L 160R
640 L 960 L 640 L 960 L 960 R 640 R 960 R 640 R
E 11 19
E 11 20
m m
960 BL 960 960 BL 960 960 960 BR 960 960 BR
160 L 160 L 160R 160R
640 L 960 L 640 L 960 L 960 R 640 R 960 R 640 R

m m
320 960 BL 960 960 BL 960
160 L 160 L
320 L 640 L 960 L 640 L 960 L
960 960 BR 960 960 BR 320
160R 160R
960 R 640 R 960 R 640 R 320 R
E 11 21
E 11 22
m m
640 960 BL 960 960 BL 960
160 L 160 L
640 L 640 L 960 L 640 L 960 L
960 960 BR 960 960 BR 640
160R 160R
960 R 640 R 960 R 640 R 640 R

m m
320 640 960 BL 960 960 BL 960
160 L 160 L
320 L 640 L 640 L 960 L 640 L 960 L
960 960 BR 960 960 BR 640 320
160R 160R
960 R 640 R 960 R 640 R 640 R 320 R
E 11 23
E 11 24
m m
320 960 960 BL 960 960 BL 960
160 L 160 L
320 L 960 L 640 L 960 L 640 L 960 L
960 960 BR 960 960 BR 960 320
160R 160R
960 R 640 R 960 R 640 R 960 R 320 R

2 3.3
1
25
1
23
3
4
24
5
7 6 23
Mounting the auger brace
15
20 21 26 22
11
8
26
19 14
17
27
13
18
18 10
12
16
E 11 25
A Before mounting the auger brace, the required auger height should already have
been set on the basic auger!
Note the section "Height adjustment for large operating widths / with brace"!
- Mount the left/right guide plates (1) on the vehicle frame shackles with the relevant
assembly parts (2).
A The guide plates must be mounted on the front side of the shackles.
- Slide the support shackle (3) over the guide plate and secure in the groove with a
pin (4) and split pin (5).
- Slide the lower support shackle (3) over the attaching point of the material shaft and
secure with a pin (6) and split pin (7).
A The brace bracket (8) is located directly on the drive unit.
A The rear brace bracket is used for the first brace set!
For larger working widths, the second brace set is mounted on the front brace
bracket.
- Insert the fulcrum bracket (10) into the brace bracket (8) and secure with the retain-
ing pin (11).
- Secure the retaining pins (11) with a split pin (12).
A The first brace set must be set in the rear bore. If the operating width necessitates a
second brace, the front bore must be used!
- Mount the slewing bracket (14) at the brace shaft (13) with retaining pins (15).
- Secure the retaining pins (15) with a split pin (16).
- Mount the braces (17) on the fulcrum bracket (10) with the assembly parts (18).
A The braces must be mounted on the outer side of the fulcrum bracket (10)!
- Remove the spring cotter pin (19) and retaining pin (20), pull out the adjustment rod
(21) until the brace can be mounted on the slewing bracket (14) together with the
corresponding assembly parts (22).
- Secure the adjustment rod (21) in an appropriate bore with a retaining pin (20) and
spring cotter pin (19).
- Mount the vertical brace (23) in the same way.

- In this case, secure the vertical brace at the outer auger bearing (24) and the low-
er support bore (25).
A At the support (3) mounting point, the brace must be secured at the rear side in each
case!
E 11 26
3.4 Aligning the auger
- Loosen lock nuts (26).
A Note the left-hand thread (L) and right-hand thread (R) mark on the brace!
- Extend or shorten the braces (17) by rotating both adjustment rods (21) until all
mounted material shafts align with the auger.
A The adjustment rod (21) is equipped with a bore (27) on the left and right. A suitable
drift can be used to adjust the length of the adjustment rod here. The rotational direc-
tion for extending or shortening the adjustment rod is determined by the left-hand
thread (L) or right-hand thread (R).
A A cord, which aligns with the screed or the rear wall of the vehicle, can be tensioned
e.g. to provide assistance during alignment!
- Extend the upper and lower adjustment rods until the material shafts are aligned
vertically.
- Retighten the lock nuts (26).

- Align the auger height in the same way by adjusting the vertical brace (23).
A Check the horizontal alignment with a spirit level!
E 11 27
m In the case of large working widths with double braces, the procedure must be carried
out on both lower pairs of braces (30) / (31) and both upper pairs of braces (32) / (33)!
31 30
32
33
E 11 28
3.5 Material shaft, hinged
To close the gap between auger box and

side board of the screen, hinged
material shafts can be fitted to both sides 4
of the auger.
A The hinged material shafts swivel up

due to the material pressure which is
exerted and swivel in due to screed
retraction.
- Mount the left/right material shafts on 2

the auger box with the relevant
assembly parts (1).
5
A If a terminal bearing is mounted for the 3
existing auger width, the adapter plate
(2) also has to be fitted. 1
- Fit the plate (3) to the hinge (5) using

the hinge rod (4).
6
A The hinged material shaft can be
secured with the assembly parts (6) in
7
swivelled in position when transporting
the machine in its basic width.
A The assembly parts (6) can be kept at

the hole (7).
E 11 29
3.6 Hopper scraper
To reduce the gap between hopper and

machine frame, the hopper scrapers (1)
must be adjusted at both hopper halves.
- Loosen the mounting screws (2).

- Adjust a gap of 6 mm across the whole
length of the scraper.
- Retighten the mounting screws (2)
properly.
f Risk of injury due to sharp-edged parts!

Wear suitable safety gloves to protect 1
your hands!
2
E 11 30
4 Offsetting the screed
Depending on the paving condition re-

quirements, the crossbeam can be
moved backwards or forwards.
This adjustment enlarges the material
space between the auger and screed.
- Loosen the four mounting screws (1).

- Remove the screws and move the ve-
hicle forwards.
- The crossbeam remains in its position
on slide rails: now tighten the screws 1
(1) back down.
A When paving thin layers, the material

can "settle" in front of the screed if the
screed is set to the rear position. When
paving thick layers, the screed then climbs better.
E 11 31
5 Levelling
5.1 Slope controller
m During operation, no work may be car-

ried out on the slope control linkage or
the slope controller!
- Mount the slope control linkage (1) in

the intended position between the two
crossbeams.
- Mount the slope controller (2) on 2
the slope control linkage's retaining
plate (3).
1
A Four securing holes are provided for
mounting on the sensor's retaining plate.
3
Querneig.wmf
A The digital slope controller must be
mounted in such a way that the marking
arrow on the housing points in the direction of travel.
A The analogue slope controller must be mounted in such a way that the displays for
the operator visibly point backwards.
- Connect the left or right connection cable to the intended handset or vehicle socket.
A Exhaustive operating instructions can be found in the documentation for the corre-
sponding levelling system.
E 11 32
5.2 Mounting the sensor arm
- Position the sensor arm mounting (1)

on the corresponding journal of the
screed side board.
- Tighten the pin (2) so that the sensor
arm is just still able to swivel.
2
A The sensor arm can be secured on the
side board with the lock (3).
3
1
Tastarm.wmf
5.3 Mounting the grade control system
Insert the grade control system into the 2

clamp bracket (1) and secure with the
clamping bolt (2) to prevent rotation.
1
F0258_A1.TIF/
E 11 33
5.4 Setting up the sensor arm
6
Before starting paving, the sensor arm 5
must be set, with the grade control sys-
tem, to its reference (cable, kerb, etc.). 4
2
A Sensing should be carried out in the
area of the auger.
3
- Swivel the sensor arm (2) over the ref-
erence.
- Use the following options to adjust the
Tastarm.wmf
sensor arm precisely:
- After loosening the clamping bolts (3), the sensor arm length can be set up.
- The sensing height can be set by loosening the clamping bolts (4).
- Adjustment of the lateral sensing angle is possible at the lock (5).
- Height adjustment for analogue grade sensors is carried out by means of a crank
(6). To lock it, the crank is inserted into one of the available notches following the
adjustment work.
A All assembly parts and clamping points must be tightened properly to ensure safe and
precise sensor arm operation!
- Connect the left or right grade control system connection cable to the intended
handset or vehicle socket.
A If the vehicle is to be operated with automatic grade sensing on both sides, the above
described adjustment process must be repeated on the second side.
A Exhaustive operating instructions can be found in the documentation for the corre-
sponding levelling system.
E 11 34
5.5 Big ski 9 m, big ski 13 m
5
3
6 8
4 2
3
7 1
2
8
MBS6.bmp
The big ski is used for contactless sensing over a particularly large reference length.
A A total max. ski length of approx. 9.30 m can be achieved with the combination of
1 centre element and 2 module elements together with the sensor arm extensions.
A total max. ski length of approx. 13.50 m can be achieved with the combination of
1 centre element and 4 module elements together with the sensor arm extensions.
A The big ski enables the alignment of the individual sensors at the front and rear to be
shifted over the reference. The sonic ski can actually be positioned in front of and be-
hind the vehicle in order to guarantee safe reference sensing even on cornering.
A Before starting paving, the big ski must be set, with the grade control system mount-
ed, to its reference (cable, kerb, etc.).
The big ski essentially consists of the following components:
- Centre element (1)

- Extension modules (2)
- Crossbeam bracket (3)
- Front swivel arm (4)
- Rear swivel arm (5)
- Sensor bracket (6)
- Sensor bracket, extendable (7)
- Arm extension (8)
E 11 35
A Assembly of the short version is described in the following, as the longer variant is
achieved simply by adding further module elements.
MBS11.bmp
The distances between the sensors are ideally identical (X1 = X2).
A The centre sensor is mounted in the usual individual sensor position so that, if nec-
essary, work can be carried out with just one sensor by switching over on the MOBA-
matic (e.g. at the start of paving, road junctions, etc…)
A Depending on application, the mechanism can be mounted at the side next to the
screed or also above the screed. This is dependent on the paving width required in
each case.
A The procedure for mounting the big ski is the same in both cases.
A So that the big ski can be operated as parallel to the ground as possible during pav-
ing, it must be attached according to the subsequent paving conditions. To do this,
the screed should be lowered to the desired course thickness and the traction point
should be set appropriately.
m When mounting the two crossbeam brackets, it is vital to ensure that these do not
hamper the free movement of either the crossbeam or the screed construction! Clear-
ance must be guaranteed throughout the entire working range!
E 11 36
Mounting the big ski bracket on the crossbeam
A The entire big ski construction is mount-

ed laterally on the crossbeams. To do
so, the two crossbeam brackets must
first be mounted. The crossbeam brack-
et design differs slightly depending on
the paver finisher which is used. 1
During assembly, it is possible either to
bolt the bracket directly at the existing
bores or, as described in the following, to
secure it to the crossbeam using clamp-
ing plates. 4
3
A The front bracket is mounted directly be- 2

hind the traction point; the rear bracket is
mounted at approximately the height of
the auger. MBS5.bmp
- Place both brackets (1) over the crossbeam at the corresponding point and mount
with bolts (2) and sleeves (3).
A For different crossbeam thicknesses, use the mounting's corresponding bores.
- The mounting tube is aligned via the two bolts (4).
A Align the bracket vertically.
E 11 37
Mounting the swivel arms
- Slide a fixing ring (1) over the tube of

the big ski bracket (2).
A The fixing ring's 45° chamfer must point

upwards.
- Then slide the two swivel arms (3)

onto the tube of the big ski bracket.
1 3
A The rear swivel arm is positioned, rotat-
ed by 180°, on the big ski bracket.
- Slide a fixing ring (4) (flat version) onto

the front swivel arm and secure with 2
the relevant star handle bolt.
MBS3a.bmp/MBS3c.bmp
E 11 38
Mounting the centre element
MBS6b.bmp
A During assembly, it must be ensured that the round lug (1) for attaching the subse-
quent modules points upwards.
A The centre element (2) is already fitted in the factory with 2 pre-assembled sliding
parts (3) / (4), which are pushed over the two round mounting journals of the swivel
arms.
- First slide the rear sliding part (3) onto the rear swivel arm from below. Then raise
the centre element, together with the rear swivel arm, until the front sliding part (4)
can be pushed onto the front swivel arm from above.
- Then secure the rear sliding part with a fixing ring (5) and the relevant star handle
bolt.
A Once the first part of the beam has been assembled, it is initially aligned:
- The centre element is now aligned horizontally using the fixing rings on the swivel
arms, and also with the fixing rings on the big ski brackets if necessary.
- Next, the centre element is aligned by rotating the swivel arms parallel to the paver
finisher.
- Finally tighten all securing bolts.
E 11 39
Extending the big ski
A The big ski can be extended to both the

9 m and 13 m versions.
A Structure of the 9 m version:

Extension part at the front/rear each.
Structure of the 13 m version:
Two extension parts at the front/rear 2
each.
1
- Place the extension module (1) onto
the centre element (2) and secure with
a bolt (3).
3
MBS1.bmp
E 11 40
Mounting the sensor bracket
A A sensing system with 3 sensors is pro-

vided over the entire length of the big ski.
One sensor each on the centre element,
2 1
and the front and rear end elements.
A The centre sensor should be mounted

on the ski in precisely the location in
which it would be found during normal
operation (approx. the height of the au-
ger).
The two other sensors should be mount-
ed the same distance away from it.
A Extendable sensor brackets (1) are

mounted in the two outer positions; the
normal sensor bracket (2) is mounted in 6
the centre.
5
- Place the sliding bracket (3) over the
corresponding big ski element from
the inner side.
- Insert the sensor bracket (4) into the
sliding bracket (5) from below and se-
cure with the relevant star handle 4
bolts.
- Place the clamping ring (6) onto the
sensor bracket tube and secure with 6
7
the relevant star handle bolt.
- In the case of the extendable sensor

MBS2.bmp/MBS12.bmp
brackets, slide in the arm extension
(7) and secure in position with the rel-
evant star handle bolt.
E 11 41
Mounting and aligning the sensors
- Insert the sensor mounting (1) into the

bracket (2).
- Align the sensor and secure with the
relevant star handle bolts.
- The sensing height can be adjusted 4
3
by loosening the star handle
bolts (3).
A At the two outer sensor brackets, the 5

sensor can also be mounted on the swiv-
elling sensor extension arm (4).
2
This therefore enables the two outer
sensors to be swivelled during paving for 1
diverse requirements, e.g. cornering.
- By loosening the star handle bolts MBS8.bmp

(5), the length of the extension arm
can be adjusted.
- The sensor bracket with extension arm can be swivelled by loosening the star
handle bolts (3).
A If a sensor extension arm is swivelled to the side, it must be ensured that the attached
sensor is subsequently aligned in the direction of travel.
A All assembly parts must be mounted and tightened properly to ensure safe and pre-
cise operation of the big ski!
E 11 42
Mounting the distributor box
A The distributor box should be mounted

in such a way that simple wiring to the
controller and the sensors is possible.
4
m The connections for the sensors should
always point down to prevent water from
3
2
entering the distributor box. Inlets which
are not required must be sealed with
dust caps.
- Allen head bolts are used to initially

mount the distributor box (1) on the
mounting plate (2). 1
A The input connector always points in the

direction of travel. MBS10.bmp
- Then mount the mounting plate on one of the two sliding brackets (4) on the centre
element using a star handle bolt (3).
m Mounting the big ski on the right-hand side of the vehicle:

To meet the requirement that the input connector always points in the direction of
travel, the sliding bracket, on which the distributor box is to be mounted, must be
pushed onto the big ski from the inside to the outside here.
E 11 43
Connection diagram
A The three sensors are connected to the

distributor box and the distributor to the
machine according to the following
scheme.
- Sensors
- Front (1) 5
- Centre (2)
- Rear (3)
- Distributor box (4)
- Machine interface (5)
1 2 3
E 11 44
6 Automatic steering unit
2
1 20
4
3
5 10
11
12
8
19
18
17 21
15
16
14
13
E 11 45
6.1 Mounting the automatic steering unit on the paver finisher
m During operation, no work may be carried out on the automatic steering unit!
A Depending on the desired sensing side on the vehicle, the sensor rod tube may have
to be removed and re-inserted on the other side of the vehicle!
- Pull the sensor rod tube (1) at the front of the vehicle out to the desired length and
secure with the clamping bolts (2).
A Only for 14m automatic steering unit:

-Push the connecting tube (3) into the sensor rod tube (1), fix with screws and lock
nuts (4).
-Push extension (5) onto the connection tube and fix in the same way.
-Fix support wheel (6) in a suitable position using the corresponding assembly parts.
-Heed vertical alignment!
- Insert tube (7) to the required length and also fix with screws and lock nuts (8).
- Fit the clamping piece (9) with extension arm (10) to the end of the tube.
A Heed vertical alignment!
- If necessary, adjust the height of the support wheel at the adjustment knob (11)
until all extension tubes are horizontally in line.
- Swivel the extension arm (9) to the desired angle and secure by tightening
the bolt (12).
m Use of the automatic steering unit increases the basic width of the paver finisher!
A If the automatic steering unit is used, ensure that there are no persons and no hin-
drances in the danger area.
E 11 46
Mounting and aligning the sensor
- Insert the sensor mounting (13) into the bracket (14) and secure with a wing
nut (15).
- Align the angle between the sensor and reference and secure with the relevant
clamping bolt (16).
A The sensor and reference must be at right angles to each other!
- The sensing height can be set by loosening the fixing screw (17).
A The reference should run centrally along the sensor.
- The sensor's distance from the reference can be set by loosening the fixing
screw (18).
A The distance between the sensor and reference (cable) should be 350 mm!
A All assembly parts must be mounted and tightened properly to ensure safe and
precise operation of the automatic steering unit!
Connecting the sensor
A A sensor for connecting the sensing system to the vehicle's control system is located
on the left and right sides of the vehicle on the inner side of the bumper.
- Connect the relevant connection cable (19) to the socket (20) and sensor (21).
A A connection socket for the automatic steering unit is located on both sides of the
vehicle.
m Route the connection cable so that it cannot be damaged during operation.
m Seal unused sockets with the relevant protective caps.
E 11 47
Automatic steering unit operating in-
structions
- When the automatic steering unit is

activated, the steering potentiometer
is deactivated. Steering is carried out
automatically via ski cable
sensing.
- Activate the function on the operating 2
panel as necessary. 1
- The automatic steering unit can be
overridden by actuating the steering
potentiometer.
- The switch (1) is used to set the sens-

ing side: Lenkski.wmf
- Right: Automatic steering unit on the

right side of the vehicle.
- Left: Automatic steering unit on the left side of the vehicle.
- The LEDs (2) indicate the distance from the reference.

- LED + / - : Distance from the reference too high / too low.
- Centre LED: Distance correct.
E 11 48
7 Emergency stop during feeder
operation
A If the function is not in use, the bridge

connector must be fitted to the corres-
ponding socket, as otherwise the travel
drive is blocked!
E 11 49
8 Limit switch
8.1 Auger limit switches

(left and right) -
mounting the PLC version
The auger's ultrasonic limit switch is 3

2
mounted on both sides on the side
board's handrail.
- Place the sensor bracket (1) onto the

handrail, align it and tighten with a 1
wing bolt (2). 4
- Align the sensor (3) and secure with a
clamping lever (4). 5
- Connect the left or right sensor's con-
nection cable (5) to the intended re-
mote control bracket sockets. Sonic.wmf
A The connection cables are connected to the relevant sockets on the remote control
bracket.
A The sensors should be adjusted so that 2/3 of the augers are covered with the paving
material.
E 11 50
9 Screed
The Operating instructions for the screed cover all work required for mounting, setting
up and extending the screed.
10 Electrical connections
Establish the following connections on the rear of the remote control brackets (1)
when the mechanical assemblies have been mounted and set up:
PLC version:
- Auger limit switches (2)

- Remote control (3)
- Grade control system (4)
- External levelling system (5)
1
A When using an external levelling sys-
tem, this must be logged in using the re-
2
mote control menu.
3
Conventional version:
- Remote control (6)

- Auger limit switches (7)
- Automatic levelling system (8) 1
A Always seal unused sockets with the rel-

evant protective caps!
6
E 11 51
10.1 Machine operation without remote control / side board
A The machine can only be driven without

connected remote control if the
corresponding bridge connectors have
been fitted on both sides of the machine.
1
Side board with mounted remote
bracket:
- Fit bridge connector (1) in the socket

of the remote control and secure with
cap.
- Check that the connection box is
plugged in (2). 2
Side board removed:
- Fit bridge connector (3) in the socket

of the connection box and secure with
cap.
E 11 52
F 10 Maintenance
1 Notes regarding safety
f Maintenance work: Maintenance work may only be carried out when the engine is
at a standstill.
Secure the paver finisher and the attachments against inadvertent starting before be-
ginning any maintenance work:
- Set the drive lever to the centre position and the speed preselector to zero.
- Pull out the ignition key and the battery main switch.
f Lifting and jacking up: Secure lifted machine parts (e.g. screed or hopper) against
lowering by means of mechanical supports.
m Spare parts: Use only approved parts and install them according to the specifica-
tions! If in doubt, contact the manufacturer!
f Re-commissioning: Mount all protective devices before re-commissioning the paver

finisher.
f Cleaning: Cleaning must not be carried out while the engine is running.
Do not use any inflammable substances (such as petrol).
Avoid directly cleaning electrical parts and insulation material with a steam jet; cover
them up beforehand.
f Working in enclosed environments: Exhaust fumes must be conducted into the

open air. Propane gas bottles must not be stored in closed rooms.
m In addition to these maintenance instructions, the maintenance instructions issued by

the engine manufacturer must be adhered to under all circumstances. All mainte-
nance work and service intervals itemised here are binding in nature.
A Information on how to maintain the optional equipment can be found in the individual
sub-sections of this chapter!
F 10 1
F 10 2
F 22 Maintenance review
1 Maintenance review
81 90 100
50
60
31
40
71
F 22 1
Maintenance required after the
following
service hours
2000 / every 2 years

1000 / annually
If necessary
Assembly Chapter
20000
5000
100
250
500
10
50
Conveyor F31 q q q
Auger F40 q q q q q q q
Engine F50 q q q q q q
Hydraulics F60 q q q q q q
Drive units F71 q q q q q q q
Electronics F81 q q q q q
Lubrication points F90 q q q q
Checking/stopping F100 q q q
Maintenance required q
A In this overview, you will find the maintenance intervals for optional machine equip-
ment!
F 22 2
F 31 Maintenance - conveyor
1 Maintenance - conveyor
F 31 1
1.1 Maintenance intervals
Interval

1000 / annually
If necessary
Item
Maintenance point Note

100
250
500
10
50
- Conveyor chain -
q
Check tightness
- Conveyor chain -
1 q
Adjust tension
- Conveyor chain -
q
Replace chain
- Conveyor drive - drive chains -
q
Check chain tightness
2
- Conveyor drive - drive chains -
q
Adjust chain tightness
- Replace conveyor deflectors /
3 q
conveyor plates
Maintenance q
Maintenance during the running-in
g
period
F 31 2
1.2 Points of maintenance
Chain tension, conveyor (1)
Check chain tension:
When the conveyor chain is correctly

tensioned, the lower edge of the chain
is approx. 20-25mm over the lower edge
of the chassis.
m The conveyor chains should not be too

tight or too slack. An excessively taut
chain can cause the chain to be stopped
or to break when material falls into the
space between the chain and the
sprocket.
An excessively slack chain may catch on
protruding objects and be destroyed.
20-25mm
Adjustment of chain tension:

x
A The chain tension is adjusted with
grease tensioners. The filling connec-
tions (A) are located behind the bumper
on the left and right sides.
A
- Add grease with a grease gun until the
correct chain tension is set.
F 31 3
Check / replace chain:
A At the latest, the conveyor chains (A)

must be replaced when their elongation
has progressed so far that they can no
longer be re-tensioned.
m Chain links must not be removed to

shorten the chain!
Incorrectly dividing the chains would
lead to the destruction of the drive
wheels! A
m If components have to be replaced as a

result of wear, the following components
should always be replaced in sets:
- Conveyor chain
- Conveyor deflectors
- Conveyor plates
- Deflector plates
- Conveyor chain reversing rollers
- Conveyor drive chain sprockets
A Your Dynapac customer service will be happy to provide support during maintenance,
repair and the replacement of wearing parts!
F 31 4
Conveyor drive - drive chains (2)
To check the chain tension:
- If the tension has been set properly,

the chain must be able to move freely
approx. 10 - 15 mm.
To re-tension the chains
- Unfasten mounting screws (A) and

lock nut (B) slightly.
- Use the tensioning screw (C) to set the
required chain tightness.
- Retighten mounting screws (A) and A A
lock nuts (B) correctly.
B
D
F 31 5
Conveyor deflectors /
conveyor plates (3)
A At the latest, the conveyor deflectors (A)

must be replaced when their lower edg-
es are worn or reveal holes.
m The conveyor chain is not offered pro-

tection by worn conveyor deflectors!
- Remove conveyor deflector bolts.

A
- Remove the conveyor deflectors from
the material tunnel.
- Install new conveyor deflectors with
new bolts.
A At the latest, the conveyor plates (B)

must be replaced when the wear limit of
5 mm in the rear area beneath the chain B
has been reached.
m If components have to be replaced as a

result of wear, the following components
should always be replaced in sets:
- Conveyor chain
- Conveyor deflectors
- Conveyor plates
- Deflector plates
- Conveyor chain reversing rollers
- Conveyor drive chain sprockets
A Your Dynapac customer service will be happy to provide support during maintenance,
F 31 6
F 40 Maintenance - auger assembly
1 Maintenance - auger assembly
F 40 1
Interval

1000 / annually
If necessary
Item
5000
100
250
500
10
50
- Outer auger bearing -

1 q
Lubricate
- Auger planetary gear -
q
Check oil level
2 q
Top up oil
g q
Change oil
- Auger drive chains -
q
Check tension
3
- Auger drive chains -
q
Adjust tension
- Auger box -
q
Check oil level
- Auger box -
4 q
Top up oil
- Auger box -
q
Change oil
- Seals and sealing rings -
q
Check wear
5
- Seals and sealing rings -
q
Replace seals
Maintenance q
g
period
F 40 2
Interval

1000 / annually
If necessary
Item
5000
100
250
500
10
50
- Gearbox bolts -
g
Check tightening
6
- Gearbox bolts -
q
Tighten to correct torque
- Outer bearing bolts -
g g
Check tightening
7
- Outer bearing bolts -
q
Tighten to correct torque
- Auger blade -
q
Check wear
8
- Auger blade -
q
Replace auger blade
Maintenance q
g
period
F 40 3
Outer auger bearing (1)
The grease nipples are located on each

side at the top of the outer auger bear-
ings.
These nipples must be lubricated at the

end of work to force out any bitumen res- 6x
idues which may have entered and to
supply the bearings with fresh grease
when warm.
A If the auger is extended, the outer rings

should be loosened slightly when initially
greasing the outer bearing points in or-
der to improve ventilation on greasing.
The outer rings must be properly se-
cured again after greasing.
A New bearings must be filled with

60 strokes of grease using a grease gun.
F 40 4
Auger planetary gear (2)
- For oil level check unscrew and re-

move the inspection bolt (A).
A When oil level is correct, the oil comes

up to the lower edge of the inspection
bore or a small amount of oil escapes
through the aperture.
For filling in the oil:

B
- Unscrew inspection screw (A) and fill-
er screw (B).
- Fill in the specified oil into the filler
bore at (B) until the oil level has A
reached the lower edge of the inspec-
tion bore (A).
- Screw the filler (B) and inspection
screws (A) back in.
To change oil:
A The oil should be changed when at oper- C

ating temperature.
- Unscrew the filler screw (B) and drain

plug (C).
- Drain the oil.
- Screw the drain plug (C) back in.
- Unscrew the inspection screw (A).
- Fill the specified oil into the filler bore at (B) until the oil level has reached the lower
edge of the inspection bore (A).
- Screw the filler (B) and inspection screws (A) back in.
F 40 5
Drive chains of the
augers (3)
To check the chain tension:
- Manually turn both augers to the right

and left. In this case, movement clearance (C) at the augers' outer circumference
should be 13-15 mm.
To re-tension the chains
- Release the mounting screws (A). A

- Set the chain tension correctly using
the threaded pins (B):
- Tighten the threaded pins to 20 Nm
using a torque wrench.
- Subsequently loosen the threaded
pins again by one full revolution.
A
- Retighten the bolts (A).
F 40 6
Auger box (4)
Check oil level
A In case of correct oil level, the oil is

between the two notches of the
dipstick (A).
- Unscrew screws (B) from the top cov-

er of the auger box.
- Take off the cover (C). A
- Fill up oil to correct level.
- Reinstall the cover.
- Use dipstick to check level again. D
Change oil
A The oil should be changed when at oper-

ating temperature.
- Place a suitable collecting container

under the auger box.
- Loosen bolts (D) from the circumfer-
B C
ence of the worm shaft flange.
A The oil runs out between the flange and

auger box.
- Drain out all oil.

- Correctly retighten flange bolts (D) di-
agonally.
- Pour the specified oil in through the
open top cover (C) of the auger box
until the oil level has reached the cor-
rect level on the dipstick (A).
- Correctly reinstall the cover (C) and
screws (B).
F 40 7
Seals and sealing rings (5)
A After reaching operating temperature,

check the gearbox for leaks.
m In case of visible leaks, e.g. between the

flange surfaces (A) of the gearbox, re-
placement of the seals and sealing rings
is necessary.
F 40 8
Gearbox bolts
Check tightening (6)
m Following the running-in period, the

tightening torques of the outer gearbox
bolts must be checked.
- Tighten to the following torques if nec-

essary: C
- (A): 86 Nm
D
- (B): 83 Nm
- (C): 49 Nm
- (D): 49 Nm
- (E): 86 Nm
m Check that each bolt has attained the full

tightening torque and note the corre-
sponding tightening pattern whilst doing A B E
so!
Mounting screws -
Outer auger bearing
Check tightening (7) C
m Following the running-in period, the

tightening torques of the outer auger
bearing mounting screws must be
checked.
- Tighten to the following torques if nec-

essary:
- (F): 210 Nm
m If the auger's working width is changed,

the tightening check must be repeated
after the running-in period!
F 40 9
Auger blade (8)
A If the surface of the auger blade (A) be-

comes sharp-edged, the diameter of the
auger is reduced and the blades (B)
have to be replaced.
- Remove the bolts (C), washers (D),

nuts (E) and auger blade (B). A
m Auger blades must be installed play-

free; the contact surfaces must be dirt-
free!
- Install the new auger blade (B); re-

place the bolts (C), washers (D) and
nuts (E) if necessary.
D
E
F 40 10
F 50 Maintenance - engine assembly
1 Maintenance - engine assembly
m In addition to these maintenance instructions, the maintenance instructions issued by

the engine manufacturer must be adhered to under all circumstances. All mainte-
nance work and service intervals itemised here are binding in nature.
F 50 1
Interval

1000 / annually
500 / annually
If necessary
Item

100
250
10
50
- Fuel tank
q
Check filling level
- Fuel tank
1 q
Refill with fuel
- Fuel tank
q
Clean the tank and system
- Engine lube oil system
q
Check oil level
q
Top up oil
2
q
Change oil
q
Change oil filter
- Engine fuel system
q Fuel filter (drain the water separa-
tor)
q
3 Replace fuel pre-filter
q
Replace fuel filter
q
Bleed fuel system
Maintenance q
g
period
F 50 2
Interval

1000 / annually
500 / annually
If necessary
Item

100
250
10
50
- Engine air filter

q
Check air filter
- Engine air filter
q Dust collector
4
Emptying
- Engine air filter
q q Air filter cartridge
Replace
- Engine cooling system
q
Check radiator fins
q q
Clean radiator fins
q
Check level of the coolant
q
5 Top up coolant
q
Check coolant concentration
q Coolant concentration
Adjust
q
Change coolant
Maintenance q
g
period
F 50 3
Interval

1000 / annually
500 / annually
If necessary
Item

100
250
10
50
- Engine drive belt

q
Check drive belt
- Engine drive belt
6 q
Tighten drive belt
- Engine drive belt
q
Replace drive belt
Maintenance q
g
period
F 50 4
Engine fuel tank (1)
- Check the filling level on the gauge

on the operating panel.
A Fill the fuel tank each time before start-

ing work so that the fuel system cannot
"run dry" and time-consuming venting
(bleeding) can therefore be avoided.
For filling in the fuel:
- Unscrew cap (A).

- Fill in fuel through the filling port until A
the required fill lever is achieved.
- Replace the cap (A).
Clean the tank and system:
- Unscrew the drain plug (B) at the bot-

tom of the tank and drain into a collec-
tion pan about 1 l fuel.
- When returning the screw, make sure
to use a new seal.
F 50 5
Engine lube oil system (2)
Check oil level
A In case of correct oil level, the oil is

between the two notches of the
dipstick (A).
A Only check the oil level when the finisher

is in a horizontal position!
m Too much oil in engine damages gas-

kets; too little oil results in overheating
and engine destruction.
A
- Remove cap (B).

- Fill up oil to correct level.
- Return cap (B).
- Use dipstick to check level again.
B
Oil change:
A The oil drain screw is accessed via the

cover (C) in the vehicle's material tunnel:
- Remove the bolts (D) from the frame

and pull the cover (C) out in the direc-
tion of travel.
C
- After completing the maintenance
work, reinstall the cover (C) properly.
A Change the oil when the engine is at op-

erating temperature.
D
F 50 6
- Position a collecting container be-
neath the oil pan oil drain screw (E).
- Remove the oil drain screw (E) and al-
low the oil to drain completely.
- Reinstall the oil drain screw (E) with a
new seal and tighten properly.
- Fill in the specified quality of oil
through the filler opening (B) on the
engine until the oil level rises to the
correct mark on the dipstick (A).
Changing the oil filter:
A All filters are accessed via the service E

flap (F) on the vehicle's centre wall:
- Remove the screws (G) from the inner

side of the frame and remove the serv- G
ice flap (F).
- After completing the maintenance F
work, reinstall the service flap (F)
properly.
A The new filter is inserted during an oil

change once the used oil has been
drained out.
- Loosen the filter (H) with a filter H

wrench or filter strap and unscrew it.
Clean the contact surface.
- Apply light coating of oil to the gasket
on the new filter and fill filter with oil
before installing it.
- Tighten filter by hand.
A After installing the oil filter, attention

must be paid to the oil pressure display
and good sealing during the test run.
Check oil level again.
F 50 7
Engine fuel system (3)
A All filters are accessed via the service

flap (A) on the vehicle's centre wall:
- Remove the screws (B) from the inner

side of the frame and remove the serv- B
ice flap (A).
- After completing the maintenance A
work, reinstall the service flap (A)
properly.
A The fuel filter system consists of two fil-

ters:
- Prefilter with water separator (C)

- Main filter (D)
Prefilter - draining of water
A Drain the collecting vessel at regular in-

tervals, or in response to an error mes-
sage from the engine control unit.
- Drain off separated water at the cock

(E) and collect, then close the cock D C G
again. A
E
F
F 50 8
Changing the prefilter:
- Drain off separated water at the cock (E) and collect, then close the cock again.
- Pull off the water sensor (F) connector.
- Loosen the filter cartridge (C) using a filter wrench or filter strap and unscrew.
- Clean sealing surface of filter bracket.
- Oil in filter cartridge gasket (only use a little oil) and screw (hand tight) under the
bracket.
- Reconnect the water sensor (F) connector.
Bleeding the pre-filter:
- Release the manual fuel pump's (G) bayonet lock by pressing and simultaneously
turning counter-clockwise.
- The pump plunger is now pressed out via the spring.
- Pump until a very high resistance is perceptible and pumping can only be carried
out very slowly.
- Now continue pumping a few more times. (The return line must be filled).
- Start the engine and operate for approx. 5 minutes at idle speed or low load.
- Check the prefilter for leaks whilst doing this.
- Lock the manual fuel pump's (G) bayonet lock by pressing and simultaneously turn-
ing clockwise.
Replacing the main filter:
- Loosen the filter cartridge (D) using a filter wrench or filter strap and unscrew.
- Clean sealing surface of filter bracket.
- Oil in filter cartridge gasket (only use a little oil) and screw (hand tight) under the
bracket.
A After fitting the filter, ensure good sealing action during the test run.
F 50 9
Engine air filter (4)
Empty dust collector
- Empty the dust removal valve (A) on

the air filter housing by compressing
the discharge slot.
- Remove any baked on dust by press-
ing together the upper valve section.
A Clean the dust removal valve from time

to time.
F 50 10
Replace air filter insert
C
A Maintenance of the filter becomes nec- B
essary if:
- Engine electronics service indicator
- Open the air filter housing (B) at the

clips (C). C
- Move filter element (D) to the side a lit-
tle and then pull it out of the housing.
- Pull out the safety element (E) and
check for signs of damage. D
A Replace the safety element (E) after the

filter has been serviced 3 times, but after
2 years at the latest (never clean it!).
F 50 11
Engine cooling system (5)
Checking / topping up coolant
The cooling water level must be checked

when the system is cold. Make sure that
the anti-freeze and anti-corrosive liquid
is sufficient (-25°C).
f When hot, the system is under pressure.

When it is opened, there is danger of
scalding! A
- If necessary fill in a sufficient amount

of coolant through the open port (A) of
the compensating tank.
Change coolant
C
f When hot, the system is under pressure.
When it is opened, there is danger of
scalding!
m Use only approved coolants!
A Observe the instructions in the chapter

entitled "Operating substances"!
B
- Remove the drain screw (B) on the ra-
diator and let the coolant drain com-
pletely.
- Reinstall the drain screw (B) and tight-
en properly.
- Fill in coolant through the filling open-
ing (A) on the compensation tank up to
approx. 7 cm (C) from the top edge of
the compensation tank.
m The air is only able to escape completely

from the cooling system once the engine
has reached its operating temperature
(at least 90°C).
Check the fluid level again, top up if necessary.
F 50 12
Checking and cleaning the radiator fins
- If necessary, remove leaves, dust or sand from the radiator.
A Observe engine's operating instructions
Checking coolant concentration
- Check the concentration using a suitable tester (hydrometer).

- Adjust the concentration if necessary.
F 50 13
Engine drive belt (6)
Check drive belts
- Check the drive belt for damage.
A Small transverse cracks in the belt are

acceptable.
m In the event of longitudinal cracks which

intersect with transverse cracks and
damaged material surfaces, belt re-
placement is necessary.
Replace drive belt
F 50 14
F 60 Maintenance - hydraulic system
1 Maintenance - hydraulic system
F 60 1
Interval

1000 / annually
If necessary
Item

100
250
500
10
50
- Hydraulic oil tank -

q
Check fill level
1 q
Top up with oil
q
Change oil and clean
q
Check maintenance indicator
2 - Hydraulic oil tank -
q q Intake / return
hydraulic filter; change, vent
- High-pressure filter -
q
Check maintenance indicator
3
- High-pressure filter -
q q
Replace filter element
- Pump distribution gear -
q
Check oil level
q
Top up oil
4 q
Change oil
q
Check bleeder
q
Clean bleeder
Maintenance q
g
period
F 60 2
Interval

1000 / annually
If necessary
Item

100
250
500
10
50
g - Hydraulic hoses -
q Visual inspection
g - Hydraulic system
q Leak test
5
- Hydraulic system
q
Retighten screw connections
- Hydraulic hoses -
q q
Replace hoses
- Auxiliary flow filter-
6 q q (o)
Replace filter element
Maintenance q
g
period
F 60 3
Hydraulic oil tank (1)
- Check oil level on sight glass (A).
A The oil level must be up to the centre of

the sight glass when the cylinders are re-
tracted.
A If all the cylinders are extended, the level

can fall below the sight glass.
A The sight glass is located on the side of

the tank.
- Remove cap (B).

- Fill in oil through the filling opening un-
A
til the oil level rises to the centre of the
sight glass (A) (+/- 5mm).
- Screw cap (B) on again.
A Regularly remove dust and dirt from the

oil tank vent (C). Clean the surfaces of
the oil cooler.
m Use only the recommended hydraulic

oils - see section "Recommended hy-
draulic oils".
A When filling for the first time, all hydraulic

cylinders should be extended/retracted
at least 2x for ventilation! B
C
F 60 4
To change oil:
- To drain the hydraulic oil unscrew the

drain plug (D) at the bottom of the
tank.
- Collect the oil in a container using a
funnel.
- When returning the screw, make sure
to use a new seal.

ating temperature. D
m When changing the hydraulic oil also

change the filter.
F 60 5
Suction/return flow hydraulic filter (2)
Carry out filter replacement according

to the interval or the indicator lamp in the
operating panel!
- Remove cover mounting screws (A)

and lift off cover.
- Disassemble the removed unit into:
- Cover (B)
- Separating plate (C) A
- Filter (D)
- Dirt trap (E)
- Clean the filter housing, cover, sepa-
rating plate and dirt trap.
- Check the O-rings (F), replace if nec-
essary.
- Coat the sealing surfaces and O-rings
with clean operating fluid.
m The filter must be bled following filter re-

placement! F
E D C B
F 60 6
Bleeding the filter
- Fill the opened filter housing with hy-

draulic oil up to approx. 2 cm below
the top edge.
A
- If the oil level drops, replenish
oil again.
A Slow oil level reduction of approx. 1 cm /

min. is normal!
- If the oil level remains stable, slowly G

insert the assembled unit with new fil-
ter element into the housing and tight-
en the cover mounting screws (A).
- Open the bleed screw (G).
- Place a transparent hose (H) onto the
bleed screw, ending in a suitable con-
tainer.
- Start the up drive engine at idle speed.
- Close the bleed screw (G) as soon as
the oil forced through the hose is clear H
and therefore free of air bubbles.
A The process from assembling the filter

cover to starting the drive engine should
take place in less than 3 minutes, as the
oil level in the filter housing otherwise
falls too far.
m Ensure seal integrity is good after changing the filter.
F 60 7
High-pressure filter (3)
The filter elements must be replaced

when the maintenance indicator (A)
turns red.
A The vehicle's hydraulic system contains

3 high-pressure filters.
- Unscrew filter housing (B).

- Remove the filter cartridge.
- Clean the filter housing.
- Insert the new filter cartridge.
- Replace the seal ring of the filter hous-
ing. A
- Turn on the filter housing by hand and
tighten it using a wrench.
- Start trial operation and check the
tightness of the filter.
A Replace the seal ring whenever the filter

cartridge is replaced.
B
A After replacing the filter element, the red

mark in the maintenance indicator (A)
automatically reverts to green.
F 60 8
Pump distribution gear (4)
- Oil level check on dipstick (A).
A The oil level must lie between the upper

and lower marks.
- Pull out the dipstick (A) completely.

- Add new oil through the dipstick open-
ing (B).
- Check the fluid level using the dip- A
stick. B
A Before checking with the dipstick, wait

for a moment, as the oil which has been
poured in first has to flow off.
m Make sure to clean the screw and the vi-

cinity of the drain bore!
Oil change:
- Place the end of the oil drain port hose

(C) in the collection container.
- Remove the screw cap with a wrench
and allow the oil to drain completely.
- Replace the screw cap and tighten C
properly.
- Pour in the prescribed quality of oil
through the dipstick opening (B).
- Check the fluid level using the dip-
stick.

ating temperature.
F 60 9
Bleeder
A The bleeder (A) can be found on the rear

of the pump distribution gear housing.
- The functioning of the bleeder must be

ensured.
If soiling has occurred, the bleeder
should be cleaned.
A
F 60 10
Hydraulic hoses (5)
- Specifically check the condition of the

hydraulic hoses.
- Immediately replace any damaged
hoses.
A Replace hydraulic hoses if the following

criteria are found on inspection:
- damage of the outer layer to the inlay

(e.g. chafing, cuts, cracks).
- brittleness of the outer layer (cracking of the hose material).
- deformation that does not correspond to the natural shape of the hose or pipe when
depressurised or under pressure or when bent (e.g. separated layers, blistering,
pinched or buckled points).
- leaks.
- damage or deformation to the hose fittings (affecting the sealing function); replace-
ments are not necessary for minor damage to the surface.
- hose coming away from the fitting.
- corrosion of the fitting with a detrimental effect on function and strength.
- failure to comply with the installation requirements.
- period of use has exceeded 6 years. Here it is the date of manufacture of the hy-
draulic hose stated on the fitting that counts, plus 6 years. If the fitting states "2004"
as the date of manufacture, the period of use ends in February 2010.
A See the section on "Marking hydraulic hoses".
f Ageing hoses become porous and may burst! Danger of accidents!
F 60 11
m Always comply with the following instructions when installing and removing hydraulic
hoses:
- Always only use original Dynapac hydraulic hoses!

- Always observe high standards of cleanliness!
- Hydraulic hoses must always be fitted to ensure that in all operating statuses,
- there is no tensile load apart from dead weight.
- there is no compressive load for short lengths.
- any external mechanical impact on the hydraulic hoses is avoided.
- appropriate positioning and fastening of the hoses prevents them from chafing on
components or on each other.
components with sharp edges must be covered when installing hydraulic hoses.
- bending radii are not smaller than the permitted values.
- When hydraulic hoses are connected to moving parts, the length of the hose must
be dimensioned to ensure that the bending radii are not smaller than the permitted
smallest values right across the full range of movement and/or that the hydraulic
hose is not also exposed to tension.
- Fasten the hydraulic hoses to the provided fastening points. the hoses must not be
hindered in their natural movement and change in length.
- Painting the hydraulic hoses is forbidden!
F 60 12
Marking hydraulic hoses / storage pe-
riod, period of use
A A number stamped onto the threaded

connection provides information about
the date of manufacture (A) (month /
year)and the maximum pressure permit-
ted for this hose (B).
m Never install hoses on top of one anoth-

er and always ensure that they are at the
correct pressure.
In individual cases, the period of use can A B

be stipulated according to experience
DHH 03/11 225BAR
and may differ from the following general
indications:
- When producing the hose pipe, the hose (purchased by the meter) should not be
more than four years old.
- The period of use of a hose pipe should not exceed six years, including any possi-
ble storage period.
The storage period should not exceed two years.
F 60 13
Auxiliary flow filter (6)
A The hydraulic oil change is omitted on

use of an auxiliary flow filter!
The quality of the oil must be checked
regularly.
The oil level must be topped up if neces-
sary!
Replacing filter element:
- Release the threaded cover connection (A) then open the non-return valve briefly
to lower the oil level in the filter, then close the non-return valve again.
- Replace filter element (B) and sealing
ring (C): A
- Turn filter element clockwise with the
help of carrier straps and, at the
same time, raise it slightly.
- Wait for a moment until the oil has
escaped downwards, then remove C
the filter element.
- Check inlet and outlet in filter
housing (D). B
- As required, top up hydraulic oil level
in filter housing then screw down the
cover. D
- Bleed the hydraulic system.
m Do not remove the cardboard sleeve

from the filter element! This is part of the
filter!
F 60 14
F 74 Maintenance – drive units
1 Maintenance – drive units
F 71 1
Interval

1000 / annually
If necessary
Item

100
250
500
10
50
- Chain tension -
q
Check
- Chain tension -
1 q
Adjust
- Chains -
q
Relieve
- Bottom plates -
q
Check wear
2
- Bottom plates -
q
Replace
- Rollers -
q
Check for leaks
- Rollers -
3 q
Check wear
- Rollers -
q
Replace
Maintenance q
g
period
F 71 2
Interval

1000 / annually
If necessary
Item

100
250
500
10
50
- Planetary gear -
q
Check oil level
- Planetary gear -
q
Top up oil
- Planetary gear -
g q
Change oil
4 - Planetary gear -
q
Check oil quality
- Planetary gear -
q
Screw connections
Check
- Planetary gear -
q
Screw connections
Tighten
Maintenance q
g
period
F 71 3
Any work on the pretensioned spring element must only be carried out by trained,
specialist personnel!
The spring elements must only be removed by a specialist workshop! The following
applies to all spring elements in the event of a necessary repair: replace the complete
unit only!
Repairing the spring elements involves significant safety measures and should only
be carried out by a specialist workshop!
Your Dynapac customer service will be happy to provide support during maintenance,
F 71 4
Chain tension (1)
If the chains are not tensioned sufficient-

m ly, they can slip out of their guide formed
by rollers, drive gear and idler wheel,
thereby increasing wear levels.
If the chains are tensioned too tightly, this increases wear on the idler wheel and drive
m unit mounting, and also increases wear on track bolts and bushes.
Checking / adjusting chain tension

x
- The chain tension is adjusted with
grease tensioners. The filling ports (A)
are located on the RH and LH sides of
the drive unit frame.
F 71 5
A B
C D
- Before checking/adjusting the chain tension, ensure that the position of the chain
to the idler wheel is as shown in diagram (A).
A Correct if necessary by moving the vehicle a little.
- Insert a measuring rule between the sliding piece (C) and (D) of the track to
determine the maximum slack:
- the distance (E) between bottom plate and measuring rule must be 10-20 mm.
F 71 6
A If a different level of slack is detected during the measurement process, proceed as
follows:
- Screw head section for flat nipple (tool

box) onto the grease gun.
- Refill the chain tensioner with grease
at the filler connection (A), then
remove the grease gun.
- Check the chain tension once again,
as described above.
A If the tension is too high: see section

"Relieving the chain".
A Repeat this procedure on both drive

units!
Relieving the chain:
The grease in the tensioning element is

f under pressure. Carefully and slowly un-
screw the filling valve, but not too far.
- Unscrew the lubricating nipple (A) on

the grease tensioner using a tool until
the grease is able to emerge from the
nipple's lateral hole.
A The idler wheel moves back independ-

ently or must be reset manually.
F 71 7
Bottom plates (2)
E
Always use new bolts and nuts when in-
m stalling new bottom plates!
- After removing the worn bottom

plates, the adhesions must be cleaned C
from the contact surfaces of the chain
links and the nut seats.
- Place the bottom plate with the front A
edge (A) over the chain links' bolt
eye (B).
- Lubricate the threads and the contact
surfaces beneath the bolt heads with a B D
thin film of oil or grease.
Bodenplatte.bmp
- Insert the bolts (C) into the holes and
screw them into the nuts (D) a few
turns.
- Tighten the bolts without applying significant torque.
- Tighten the bolts diagonally to the required torque 155 ± 8 Nm (E).
Check that each bolt has attained the full tightening torque!
m
F 71 8
Rollers (3)
Rollers with damaged surfaces or which

m are leaking should be replaced immedi-
ately!
- Relieving the caterpillar chain:

- Raise the track chassis using suitable
lifting equipment and remove adhering B
dirt.
Observe the safety measures when rais-

f ing and securing loads!
A
- Remove the defective roller.

- Install the new roller using new as-
sembly parts.
- Tighten the bolts without applying sig-

nificant torque.
- Tighten the bolts diagonally to the re-
quired torque.
- Tighten to the following torques:

- Small rollers (A): 210 Nm
- Large rollers (B): 85 Nm
Check that each bolt has attained the full tightening torque!
m
- Lower the track chassis and tension the caterpillar chain properly.
F 71 9
Planetary gear (4)
- Turn the conveyor chain sprocket so

that the drain plug (B) is located at the
bottom.
- For oil level check unscrew and re-
move the inspection bolt (A).
A When oil level is correct, the oil comes

up to the lower edge of the inspection
bore or a small amount of oil escapes
through the aperture.
- Unscrew the filler screw (A).

- Fill in the specified oil into the filler
bore at (A) until the oil level has
reached the lower edge of the filler
bore.
- Screw the filler screw (A) back in. A
Oil change:
B
ating temperature.
Ensure that no dirt or foreign bodies are

m able to enter the gear.
- Turn the conveyor chain sprocket so

that the drain plug (B) is located at the bottom.
- Unscrew and remove the drain plug (B) and filler screw (A) and drain off oil.
- Check gaskets on both screws and replace if necessary.
- Screw the drain plug (B) in.
- Fill new oil through the filler opening until the lower edge of the opening is reached.
- Tighten the filler screw (A).
F 71 10
A Alternatively, the oil level can be checked and the oil changed at the rear of the gear-
box:
- Remove protective cover (A)

- The following are located at the rear of
the gearbox:
- Oil inlet (B)
- Oil level check (C)
- Oil drain (D)
A Carry out the oil level check and oil A

change as per the description above.
When draining using the drain (D), a

m small residual quantity of oil remains in
the gearbox.
- Max. oil level up to lower edge of oil

check (C).
- Reinstall the protective cover (A) prop-
erly.
B C
F 71 11
Screw connections
After approx. 250 hours of operation at

m full load, check that all gearbox mount-
ing screws are firmly seated.
Improperly tightened screws may lead to

m increased wear and to the destruction of
components! A
- The correct tightening torque for the

connecting screws for the
gearbox - chain sprocket (A)
is: 315 Nm
gearbox - drive unit frame (B)
is: 580 Nm
hydraulic motor - gearbox (C)
is: 410 Nm B
C
F 71 12
F 71 13
F 81 Maintenance - electrical system
1 Maintenance - electrical system
F 81 1
Interval

1000 / annually
If necessary
Item

100
250
500
10
50
Filling level of
q
battery electrolyte - check
1
q Top up with distilled water
q Apply grease to battery terminals
- Generator
Electrical system insulation
q (o)
monitoring
Check function
2 - Alternator
Visual check for pollution
or damage
q (o)
- Check the cooling air openings for
pollution or clogging, clean if nec-
essary.
3 q Electrical fuses
Maintenance q
g
period
F 81 2
Batteries (1)
Maintenance of batteries
A The batteries are factory-filled with the

correct quantity of acid. The fluid level
should come up to the top mark. If re-
quired, top up the battery, but only use
distilled water to do so!
m The battery terminal clips must be free of

oxide and protected with a special termi-
nal grease.
m When removing the batteries, always

first remove the negative terminal, en-
suring that the battery terminals cannot
be short circuited.
F 81 3
Alternator (2)
Electrical system insulation monitoring
The function of the protective insulation

monitoring measure must be checked
every day before starting work.
A This check only checks the function of

the insulation monitor, not whether an in-
sulation error has occurred on the heat-
ing sections or consumers. 1
- Start the paver finisher's drive engine.

- Switch heating system switch (1) 3
to ON.
- Press test button (2). 2
- The indicator lamp integrated into the
test button signals "insulation fault".
- Press reset button (3) for at least
3 sec. to delete the simulated fault.
- The indicator lamp goes out.
f If the test is conducted successfully,

work may be undertaken with the screed
and external consumers may be used.
If the "insulation fault" indicator lamp displays a fault even before the test button is
pressed or if no fault is displayed during the simulation, work must not be undertaken
with the screed or with connected, external equipment.
f The screed and equipment must be checked or repaired by a specialist electri-

cian. Only then may work again be undertaken with the screed and equipment.
f Danger due to electrical voltage
f Non-adherence to the safety precautions and safety regulations

when operating the electric screed heating system leads to a
risk of electric shock.
Danger to life.
All maintenance and repair work on the screed's electrical system may be car-
ried out by a specialist electrician only.
F 81 4
Insulation faults
A If an insulation fault occurs during operation, and the indicator lamp displays an insu-
lation fault, the operator may proceed as follows:
- Switch the switches of all external equipment and the heating system to OFF and
press the reset button for at least 3 seconds to delete the fault.
- If the indicator lamp does not go out, the fault lies in the generator.
f No further work may be carried out.
- If the indicator lamp goes out, the switches of the heating system and external
equipment can be switched back to ON one after another until a message again
appears and the system is shut-down.
- The equipment found to be faulty must be removed or must not be engaged, and
the reset button must be pressed for at least 3 seconds to delete the fault.
A Operation may now be continued - without the faulty equipment, of course.
A The generator or electrical consumer found to be faulty must be

checked or repaired by a specialist electrician. Only then may
work again be carried out with the screed and equipment.
F 81 5
Cleaning the generator
m The generator must be regularly

checked for excessive dirt and must be
cleaned if necessary.
1
- The air intake (1) and fan shroud (2)
must be kept free of dirt.
m Cleaning with a high-pressure cleaner is

not permissible!
F 81 6
Electrical fuses / relays (3)
15
10
25
10
15
15
25
15
10
15
25
15
10
15
25
15
10
10
A Main fuses
B Fuses in terminal box
C Relays in terminal box
Main fuses (A)
F A
F1.1 Main fuse 50
F1.2 Main fuse 50
F 81 7
Fuses in terminal box (B)
15
10
25
10
15
15
25
15
10
15
25
15
10
15
25
15
10
10
F 81 8
F A
F1 Screed 10
F2 Screed 10
F3 Levelling 10
F4 Engine start / emergency stop 5
F5 not used
F6 not used
F7 not used
F8 Emergency stop / remote steering 5
F9 Emulsion spraying system 5
F10 Travel drive sensors 7,5
F11 Electric heating 10
F12 Conveyor sensors 7,5
F13 12V socket 10
F14 not used
F15 not used
F16 24V socket 10
F17 Display voltage supply 5
F18 Keyboard voltage supply 10
F19 Engine compartment lighting 10
F20 Rotary beacon 7,5
F21 Travel drive computer voltage supply 25A
F22 Travel drive computer voltage supply 25A
F23 Horn 15
F24 Engine start 10
F25 Windscreen wiper 5
F26 Engine control unit 30
F27 Keyboard / display constant positive 2
F28 not used
F29 Ignition 3
F30 Reverse buzzer 5
F31 Diesel pump 5
F32 Travel drive computer control voltage 20
F33 not used
F34 Seat heating 5
F35 Rear working lights 10
F36 Front working lights 10
F37 Engine interface 2
F38 Interface 2
F 81 9
Relays in terminal box (C)
15
10
25
10
15
15
25
15
10
15
25
15
10
15
25
15
10
10
F 81 10
K
0 Engine start
1 Ignition
2 Travel drive computer voltage supply
3 Travel drive computer voltage supply
4 Engine start
5 Travel drive computer control voltage
6 Keyboard / display
7 Front working lights
8 Rear working lights
9 Horn
10 Start inhibit, emergency stop
11 Start inhibit
12 Rotary beacon
13 Seat heating
14 Windscreen wiper
15 Windscreen washer system
16 Reverse buzzer
17 Diesel pump
18 not used
19 not used
20 not used
21 not used
22 not used
23 not used
24 not used
25 not used
26 not used
27 not used
28 not used
29 Central lubrication
F 81 11
Relays in the engine compartment (E)
K
0 Engine start
F 81 12
F 90 Maintenance - lubricating points
1 Maintenance - lubricating points
A The information on the lubricating points for the various assemblies is assigned to the
specific maintenance descriptions and must be read there!
F 90 1
A Due to the use of a central lubrication system (o), the number of lubricating points
may deviate from the description.
Interval

1000 / annually
If necessary
Item

100
250
500
10
50
q - Check lubricant tank fill level (o)
q - Top up lubricant tank (o)
q - Bleed central lubrication system (o)

1
q - Check pressure limiting valve (o)
- Check flow of lubricant at the

q (o)
consumer
2 q - Bearing points
Maintenance q
Maintenance during the running-in g
period
F 90 2
Central lubrication system (1)
Danger of injuries!
f Do not reach into the tank when the

pump is running!
f The central lubrication system must only

be operated with the safety valve in-
stalled!
Handverl.jpg/Gefahr.jpg
f Do not undertake any work on the pres-

sure relief valve during operation!
f Risk of injury due to escaping lubricant, as the system operates at high pressures!
f Ensure that the diesel engine cannot be started when working on the system!
f Observe safety regulations for handling hydraulic systems!
m Ensure maximum cleanliness when working on the central lubrication system!
The following assemblies' lubricating

points can be automatically supplied
with grease by the central lubrication
system:
- Conveyor
- Auger
- Steering, axles (wheeled pavers)
- Screed (tamper / vibration)
F 90 3
Central lubrication system
Check filling level
A The lubricant tank should always be

filled sufficiently to ensure that the sys-
tem does not "run dry", that adequate lu-
bricating point supply is ensured and a
that time-consuming bleeding does not
become necessary.
- Always maintain a fill level above the

"MIN" mark (a) on the tank.
Top up lubricant tank
- A lubricating nipple (b) is located on the lubricant tank (a) for filling purposes.
- Connect the grease gun (c) enclosed on delivery to the filling nipple (b) and fill
the lubricant tank (a) up to the MAX mark.
- Alternatively, unscrew cover (d) and fill tank from above.
A When the lubricant tank is completely empty, the pump may have to run for up to
10 minutes until the full delivery rate is achieved after filling.
F 90 4
Bleed central lubrication system
Bleeding the lubrication system is nec- c

essary if the central lubrication system
has been operated with an empty lubri-
cant tank. a
- Release the main lubrication line (a)

at the distributor (b). d
- Start up the central lubrication sys-
tem with the filled lubricant tank (c).
- Allow the pump to run until lubricant
emerges from the previously re- d
leased main line (a).
- Reconnect the main line (a) to the b
distributor.
- Release all distribution lines (d) from
the distributor.
- Reconnect all distribution lines as soon as lubricant has emerged.
- Check all connections and lines for leaks.
Check pressure limiting valve
m If lubricant emerges at the pressure lim-

iting valve (a), this indicates a malfunc-
tion in the system.
The consumers are no longer adequate-
ly supplied with lubricant.
- Release all distribution lines (b) a

leading from the distributor (c) to the
consumers in succession.
- If lubricant emerges from one of the
released distribution lines (b) under
pressure, search in this lubrication
circuit for the cause of the blockage
which has triggered the pressure
limiting valve. b
- After rectifying the malfunction and
reconnecting all lines, again check
the pressure limiting valve (a) for lu- b
bricant emergence.
- Check all connections and lines for
leaks. c
F 90 5
Check the flow of lubricant at the con-
sumers
a
Each lubrication channel at the consum-
ers must be checked as regards clear-
ance.
- Remove the lubrication line (a) and

install a normal lubricating nipple (b).
- Connect the grease gun (c) en-
closed on delivery to the lubricating
nipple (b).
- Operate the grease gun until the lu- b
c
bricant visibly emerges.
- Rectify any faults in the flow of lubri-
cant.
- Reinstall the lubrication lines.
- Check all connections and lines for
leaks.
F 90 6
Bearing points (2)
A One lubricating nipple (A) is located at

each hydraulic cylinder bearing point 2x
(top and bottom).
A One lubricating nipple (B) is located at

each push roller bearing point. 2x
F 90 7
F 90 8
F 100 Tests, stopping ...
1 Tests, checks, cleaning, stopping
F 100 1
Interval

1000 / annually
If necessary
Item

100
250
500
10
50
1 q - General visual inspection
2 q q - Inspection by an expert
3 q - Cleaning
4 q - Preserving the paver finisher
Maintenance q
g
period
F 100 2
2 General visual inspection
The daily routine should comprise a visual inspection around the entire paver finisher.
The following items must be checked:
- Are components or controls damaged?

- Are there leaks on the engine, the hydraulics, the gearbox, etc.?
- Are all fastening points (conveyor, auger, screed, etc.) in order?
m Immediately take actions to correct any detected malfunction to avoid damages, dan-
gers or environmental hazards!
3 Inspection by an expert
A Have finisher, screed and optional gas or electric system checked by a trained spe-
cialist
- when required (according to the operating conditions and the nature of application),
- however, at least once a year, check that they are all in good operational condition.
F 100 3
4 Cleaning
- Clean all parts coming into contact with paving material.

- Spray contaminated parts with the separator fluid spraying system (o).
m Before cleaning work with the high pressure cleaner, grease all lube points acc. to
specification.
- Clean the vehicle with water after laying mineral aggregates, lean-mixed concrete,
etc.
m Do not spray bearing points, electrical or

electronic components with water.
- Remove residual paving material.
m After cleaning work with the high pres-

sure cleaner, grease all lube points acc. to specification.
f Danger of slipping! Ensure that all steps

and ladders are free of grease and oil!
F 100 4
5 Preserving the paver finisher
5.1 Shutdowns for up to 6 months
- Park the vehicle in a place where it is protected from great exposure to direct sun-
light, wind, humidity and frost.
- Grease all lube points in accordance with specifications. Allow optional central lu-
bricating unit to run if necessary.
- Change oil in diesel engine.
- Seal exhaust silencer to make it airtight.
- Remove batteries, charge them and store them in a well ventilated place at room
temperature.
m Recharge removed batteries every 2 months.
- Protect all bare metal components, e.g. piston rods on hydraulic cylinders, with a
suitable corrosion inhibitor.
- If it is not possible to park the vehicle is an enclosed building or under cover, it must
be covered with a suitable size of tarpaulin. In all cases, seal all air intake and ex-
haust apertures with plastic film and adhesive tape.
5.2 Shutdowns lasting from 6 months to 1 year
- Carry out all the actions listed for "Shutdowns of up to 6 months".

- Once the engine oil has been drained off, fill the diesel engine with a manufacturer-
approved grade of preserving oil.
5.3 Recommissioning the machine
- Reverse all the steps described in the "Shutdown" sections.
F 100 5
6 Environmental protection, disposal
6.1 Environmental protection
A Packaging materials, used operating substances, cleaning agents and machine ac-
cessories must be correctly recycled.
A Always observe the local regulations!
6.2 Disposal
A Correctly sorted disposal must be carried out after replacing wear and spare parts
and after the machine has been withdrawn from service (scrapped).
The materials must be sorted correctly according to metal, plastic, electronic scrap,
various operating substances etc.
Any oily or greasy parts (hydraulic hoses, lube pipes etc.) must be treated separately.
A Electric devices, accessories and packaging should be recycled in an environment-

friendly manner.
A Always observe the local regulations!
F 100 6
F 110 Lubricants and operating
substances
1 Lubricants and operating substances
m Use only the lubricants listed below or comparable qualities of well-known brands.
m Only use containers which are clean on inside and outside for filling oil or fuel.
A Note capacities (see section "Capacities").
m Incorrect oil or lubricant levels promote rapid wear and paver finisher failure.
m Never mix synthetic oils with mineral oils!
F 110 1
2
4 3 1
F 110 2
1.1 Capacities
Substance Volume
Diesel engine
1 Engine oil 13 litres
(with oil filter change)
2 Engine cooling system Cooling liquid 20.0 litres
3 Fuel tank Diesel fuel 350 litres
4 Hydraulic oil reservoir Hydraulic oil 200 litres
5 Pump distribution gear Gearbox oil 7.0 litres
Planetary gear
6 Gearbox oil 3.5 litres
drive unit
Planetary gear
7 Gearbox oil 1.5 litres
augers (on each side)
7 Auger box Gearbox oil 5.0 litres
Outer auger bearing

7 Hot bearing grease 115 grammes
(per bearing)**
Central lubrication system

Grease
(option)
Batteries Distilled water
m Note specifications on the following pages!
** for new installation
F 110 3
2 Lubricant specifications
2.1 Engine
Atlas Copco Aral BP Esso / Exxon Fuchs Mobil Shell
Engine Oil -Rimula

100 R6LM
(*) 10W-40
A (*) = recommended
2.2 Cooling system
Atlas Copco AGIP Chevron Caltex Delo Mobil Shell
Coolant
-Antifreeze Extended Extended Extended
100
Spezial Life Coolant Life Coolant Life Coolant
(*)
A (*) = recommended
2.3 Hydraulic system
Atlas Copco AGIP Chevron Caltex Fuchs Mobil Shell
Hydraulic
Rando Rando -Tellus Oil
100
HDZ 46 HDZ 46 S2 V46
(*)
A (*) = recommended
2.4 Pump distribution gear
Esso /
Dynapac Aral BP Fuchs Mobil Shell
Exxon
-Spirax S4
-Titan ATF ATF HDX
6000 SL (*) -Spirax S4
ATF VM
A (*) = filled in at the factory
F 110 4
2.5 Drive unit planetary gear
Traction
-Omala
Gear 100
Oil F 220
(*)
A (*) = recommended
2.6 Auger drive planetary gear

Traction
-Omala
Gear 100
Oil F 220
(*)
A (*) = recommended
2.7 Auger box
Dynapac Aral BP Esso / Exxon Fuchs Mobil Shell
-Omala
S4WE460
(*)
A (*) = recommended
2.8 Grease
Dynapac Aral BP Esso / Exxon Fuchs Mobil Shell Chevron
Paver -High
-Gadus S5
Grease Temp
T460 1.5
(*) Premium2
A (*) = recommended
F 110 5
2.9 Hydraulic oil
Preferred hydraulic oils:
a) Synthetic hydraulic liquids based on ester, HEES
Manufacturer ISO viscosity class VG 46
Atlas Copco Hydraulic 120 (*)
Shell Naturelle HF-E46
Panolin HLP SYNTH 46
Esso Univis HEES 46
Total Total Biohydran SE 46
Aral Vitam EHF 46
A (*) = recommended
b) Mineral oil pressure fluids
Manufacturer ISO viscosity class VG 46
Atlas Copco Hydraulic 100 (*)
Shell Tellus S2 V46
Chevron Rando HDZ 46
Caltex Rando HDZ 46
A (*) = recommended
m When changing from mineral oil pressure fluids to biodegradable pressure fluids,
please contact our factory advisory service!
F 110 6
Parts & Service
Training
We offer our customers training courses on DYNAPAC equipment in our dedicated factory training centre.
We hold regular training courses in this training centre as well as courses outside the scheduled hours.
Service
Please contact one of our responsible service outlets if you encounter any operational problems or have
enquiries about spare parts.
Our trained, specialist staff will ensure that you receive prompt attention and repairs in the event of any ac-
cident or malfunction you may encounter.
Factory Advisory Service

If ever for any reason our dealership network encounters limits to what it is able to do for you, please always
feel free to contact us directly.
Our team of technical advisers is on hand to assist you.
gmbh-service@atlascopco.com
www.atlascopco.com

Operation & Maintenance: Paver Finisher Dynapac SD2550C / SD2550CS

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Operation & Maintenance: Paver Finisher Dynapac SD2550C / SD2550CS

Uploaded by

Copyright:

Available Formats

OPERATION & MAINTENANCE

A Correct use and application .......................................................... 1

B Vehicle description ......................................................................... 1

6.3 Instructive symbols, prohibitive symbols, warning symbols ................... 26

C11 Transportation ................................................................................... 1

D20 Operation ........................................................................................... 1

D30 Operation ............................................................................................. 1

D41 Operation ................................................................................................ 1

E11 Set-up and modification ................................................................ 1

F22 Maintenance review .. ........................................... .......................... 1

F31 Maintenance - conveyor ................................................................... 1

F40 Maintenance - auger assem bly ......................... .......................... 1

F50 Maintenance - engine assembly ......................... .......................... 1

F71 Maintenance – drive units ............................................................ 1

F81 Maintenance - electrical system ..................................................... 1

F90 Maintenance - lubricating points ................................................... 1

F110 Lubricants and operating

Dynapac (China) Compaction & Paving Equipment Co., Ltd.

1.1 Laws, guidelines, accident prevention regulations

1.3 Other supplementary information

Precedes notes that must be observed to prevent damage to equipment.

Warning on a dangerous area or hazard!

Warning on danger of being pulled in!

In this working area/on this element there is a danger of being pulled

Warning on dangerous electrical voltage!

All maintenance and repair work on the screed's electrical system

Warning on suspended loads!

Never stand under suspended loads!

Warning on danger of crushing!

m There is a danger of crushing when certain components are operat-

Warning on hand injuries!

Warning on hot surfaces or hot liquids!

Warning on dangers posed by batteries!

Warning on hazardous or irritating substances!

Warning on substances which constitute a fire hazard!

Warning on gas bottles!

Opening/walking on/reaching in/carrying out/setting up are prohibit-

Do not start engine/drive!

Spraying with water is prohibited!

Extinguishing with water is prohibited!

Unauthorised maintenance is prohibited!

A Consult the Dynapac Service Department

Fire!, naked flames and smoking are prohibited!

Wear safety goggles to protect your eyes!

Wear suitable head protection!

Wear suitable hearing protection to protect your hearing!

Wear suitable safety gloves to protect your hands!

Wear safety shoes to protect your feet!

Always wear close-fitting work clothing!

Wear respiratory equipment if breathing air is contaminated!

- Lubricants (oil, grease)

Substances must be caught, stored, transported and brought to pro-

Environmentally hazardous substance!

1.8 Fire prevention

A Locally applicable regulations may require suitable extinguishing agents to be carried

Also observe the manufacturer's documentation and additional doc-

A For example, the maintenance instructions of the engine manufac-

Description / depiction applicable when equipped with gas heater!

Description / depiction applicable when equipped with electric heat-

t Used to indicate standard equipment.

o Used to indicate optional equipment.

(only applies to machines sold in the EU/EEC)