Power Transformers Principles and Application

Power
Transformers
Principles and Applications
John J. Winders, Jr.

PPL Electric Utilities
Allentown, Pennsylvania
Marcel Dekker, Inc. New York • Basel

TM
Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

ISBN: 0-8247-0766-4
This book is printed on acid-free paper.
Headquarters
Marcel Dekker, Inc.
270 Madison Avenue, New York, NY 10016
tel: 212-696-9000; fax: 212-685-4540
Eastern Hemisphere Distribution

Marcel Dekker AG
Hutgasse 4, Postfach 812, CH-4001 Basel, Switzerland
tel: 41-61-261-8482; fax: 41-61-261-8896
World Wide Web

http:/ /www.dekker.com
The publisher offers discounts on this book when ordered in bulk quantities. For more
information, write to Special Sales/Professional Marketing at the headquarters address
above.
Neither this book nor any part may be reproduced or transmitted in any form or by
any means, electronic or mechanical, including photocopying, microfilming, and re-
cording, or by any information storage and retrieval system, without permission in
writing from the publisher.
Current printing (last digit):

10 9 8 7 6 5 4 3 2 1
PRINTED IN THE UNITED STATES OF AMERICA

Series Introduction
Power engineering is the oldest and most traditional of the various areas within
electrical engineering, yet no other facet of modern technology is currently
experiencing a greater transformation or seeing more attention and interest
from the public and government. But while public concern and political deci-
sions about de-regulation and energy trading may reshape the electric utility
industry’s manner of doing business, its future like its past rests on the capabil-
ity of its transmission and distribution systems to convey safe, reliable, and
economical electric power to homes, businesses, and factories. Nothing is
more essential to this performance than the transformer, which enables modern
power and industrial systems to function.
I am particularly delighted to see this latest addition to Marcel Dekker’s
Power Engineering series. Power Transformers: Principles and Applications
is a comprehensive compendium of theory and practices for electric power
transformers. This book provides a concise but thorough treatment of basic
transformer theory, its application to various types of transformer designs and
their application in utility and industrial power systems. Its easy to read style
and linear organization make it particularly suitable as a tutorial for those who
need to learn the material independently, outside of the classroom, or as a text

for formal courses. This book also makes a very good practical reference for
utility and industrial power engineers.
In addition to having concise summaries of all the basics, the text pro-
vides an excellent description of the various ancillary equipment and systems,
which are often the most difficult to precisely engineer and fit into the system.
John Winders has also provided excellent coverage of how to read, interpret,
and apply a power transformer’s nameplate data, not always a straightforward
or unambiguous task and one where a surprising number of mistakes are made
by inexperienced engineers. Chapter 8 will be particularly useful to practicing
engineers and power system operators, covering maintenance needs, testing
options, and troubleshooting techniques and their use, and discussing reliabil-
ity of transformers.
As the editor of the Power Engineering series, I am proud to include
Power Transformers: Principles and Applications among this important group
of books. Like all the books in Marcel Dekker’s Power Engineering series,
this book provides modern power technology in a context of proven, practical
application, useful as a reference book as well as for self-study and advanced
classroom use. Marcel Dekker’s Power Engineering series includes books cov-
ering the entire field of power engineering, in all of its specialties and sub-
genres, each aimed at providing practicing power engineers with the knowl-
edge and techniques they need to meet the electric industry’s challenges in
the 21st century.
H. Lee Willis

Preface
This book is based on notes for the Transformer Applications Course offered
by the Center for Power System Study at Lehigh University. The key word
in both the title of that course and the title of this book is applications. The
material presented in the following chapters was obtained from various
sources: textbooks, industry standards, and established utility practices and
procedures. Much of this material also comes from my personal files relating
to actual events and case studies that were observed during my career in the
utility industry spanning 30 years.
There are many kinds of transformers, and all share the same set of
fundamental operating principles. Since this book focuses on power transform-
ers, it is fair to ask, ‘‘What exactly is a power transformer?’’ By definition,
a power transformer is a transformer which transfers electric energy in any
part of the circuit between the generator and the distribution primary circuits.*
This definition of power transformer in the IEEE standard appears under the
* IEEE Std. C57.12.80-1978. IEEE Standard Terminology for Power and Distribution Transform-
ers. Institute of Electrical and Electronics Engineers, Inc., 1978, New York, p. 8.

heading of ‘‘Size’’ and does not indicate how the transformer is used in the
power system. Thus, this book uses this definition in the broadest sense to
include discussions of specialty applications such as step voltage regulators,
phase shifters, and grounding transformers, as well as the usual step-up and
step-down applications. Since the line between power transformers and distri-
bution transformers is somewhat blurry, many of the basic principles presented
can be applied to distribution transformers as well.
The first several chapters build a solid theoretical foundation by describ-
ing the underlying physics behind transformer operation. A theoretical founda-
tion is absolutely necessary in order to understand what is going on inside a
transformer and why. The magnetic properties of materials, a review of mag-
netic units, and analysis of magnetic circuits are discussed with enough mathe-
matical rigor for the interested reader to gain full comprehension of the physics
involved. Whenever a detailed mathematical treatment is presented, it is al-
ways done with a practical objective in mind. Each chapter includes a number
of practice problems to clearly illustrate how the theory is applied in everyday
situations. Many of these practice problems are based on actual events.
Several things set this book apart from other transformer reference
books. First, this book emphasizes the importance of magnetic properties and
how the choice of a core design can affect the transformer’s electrical proper-
ties, especially during faults and unbalanced operations. Many reference books
overlook this critical aspect of transformer applications.
Next, this book discusses special types of transformer connections, such
as the zigzag, Scott, and tee connections, as well as the more common wye
and delta types. The Scott and tee connections, which transform three-phase
voltages into two-phase voltages, are seldom covered in modern transformer
reference books even though two-phase systems still exist today. Tap changing
under load and variable phase shifting transformers are covered. Different
types of transformer coil and coil construction are compared, with discussion
of the particular advantages and disadvantages of each with respect to the
various transformer connections. The reader will also gain insight into some
of the economic trade-offs of different transformer design options.
A brief tutorial on symmetrical components is also included. The topic
is covered in other reference books but seldom in such a compact and straight-
forward way, enabling the reader to immediately apply the technique in practi-
cal problems.
A section of the book defines a transformer’s nameplate rating versus
its thermal capability and describes how to calculate a transformer’s rate of
loss of life. An entire chapter is devoted to describing abnormal operating
conditions that can damage power transformers, including overloads, short

circuits, single phasing from primary fuse operations, ferroresonance, and
voltage surges. The chapter describes ways to avoid these conditions, or at
least ways to mitigate them through proper system design and selection of
appropriate transformer designs.
The reader will learn how to interpret and use a transformer test report
as well as the information on the transformer nameplate. The book concludes
with a comprehensive discussion of preventive and predictive maintenance,
good utility practices, factory and field testing, and failure rate analysis.
This book is intended primarily for readers having an electrical engi-
neering background although training as an electrical engineer is not neces-
sary, and others will also benefit from the conclusions that can be drawn from
the practical examples. Mastery of the principles presented in this book will
provide a sound working knowledge of how to specify, operate, and maintain
power transformers in a utility or plant environment.
I wish to thank Anthony F. Sleva for his thorough review of the manu-
script and his many helpful suggestions for improving it, and for making it
possible to publish this book. I am indebted to the late Charles H. Morrison,
who patiently shared with me so much of his extensive theoretical and practi-
cal knowledge about power transformers.
John J. Winders, Jr.

Contents
Series Introduction H. Lee Willis

Preface
1 Basic Transformer Theory
1.1 Definition of a Transformer

1.2 Magnetic Units and Conversion Factors
1.3 Currents and Magnetic Fields
1.4 Magnetic Induction
1.5 Constructing a Simple Transformer
1.6 The Magnetic Circuit
1.7 The B-H Curve
1.8 The B-H Curve and Hysteresis
1.9 Magnetizing Currents and Harmonics
1.10 Transformer Core Design and Construction
1.11 Magnetostriction
1.12 Completing the Transformer by Adding a Second
Winding

1.13 Placement of the Windings
References
2 Two-Winding Transformer Connections
2.1 Introduction
2.2 The Y-Y Connection in Three-Phase Systems
2.3 Advantages of the Y-Y Connection
2.4 Disadvantages of the Y-Y Connection
2.5 The Y-∆ Connection and the ∆-Y Connection
2.6 Phase Angle Displacement and Phase Rotation
2.7 The Y-∆ Grounding Bank
2.8 The Zigzag Connection
2.9 Comparisons of Economy of the Different Winding
Configurations
2.10 Trade-Off Between Steel and Copper in the Design of a
Transformer
2.11 Connecting Three-Phase Banks Using Single-Phase
Transformers
2.12 Transforming Three-Phase Voltages into Two-Phase
Voltages
2.13 The Scott Transformer Connection
2.14 Three-Phase Transformer Designs
2.15 Standard Terminal Markings for Transformers
References
3 Transformer Impedance and Losses
3.1 Leakage Flux and Leakage Reactance

3.2 Conductor Losses
3.3 No-Load Losses
3.4 Magnetizing Reactance
3.5 Equivalent Circuit of a Two-Winding Transformer
3.6 A Brief Tutorial on Symmetrical Components
3.7 Transformer Equivalent Circuits Modeled in Zero Phase
Sequence Networks
3.8 Series Impedance and Regulation
3.9 Matching Transformers for Parallel and Bank
Operations

3.10 Impedance Mismatch in Three-Phase Transformer
Banks
3.11 Temperature Rise and the Thermal Capability
3.12 Interpreting Transformer Test Reports
3.13 Calculating the Hot-Spot Temperature Using the IEEE
Method
3.14 Calculating the Loss of Life
References
4 Autotransformers and Three-Winding Transformers
4.1 Autotransformer Connections

4.2 Impedance of an Autotransformer
4.3 Limitations of the Autotransformer Connection
4.4 Autotransformer Voltages with Short Circuits Applied
4.5 Impulse Voltages Applied to Autotransformers
4.6 Autotransformer Core and Coil Designs and Terminal
Configurations
4.7 Advantages and Disadvantages of the Autotransformer
Connection
4.8 Three-Winding Transformers
4.9 Modification of Transformer Laws with Three Windings
4.10 Equivalent Circuit of a Three-Winding Transformer
4.11 Core and Coil Construction of Three-Winding
Transformers
4.12 Thermal Capability of Three-Winding Transformers
4.13 The Stabilizing Effect of a ∆ Tertiary Winding
Reference
5 Short Circuits, Inrush Currents, and Other Phenomena
5.1 Effects of Short Circuits on Transformers

5.2 Comparisons of Short-Circuit Currents for Various
Faults
5.3 Mechanical Forces in Transformers
5.4 Forces between Transformer Windings
5.5 Short-Circuit Forces in Three-Winding Transformers
5.6 Exciting Current Inrush
5.7 Tank Overheating from Zero-Sequence Currents

5.8 Primary Fuse Misoperations
5.9 Ferroresonance
5.10 Voltage Surges
References
6 Ancillary Equipment
6.1 Bushings
6.2 Oil Preservation Systems
6.3 Cooling Equipment
6.4 Temperature, Oil Level, and Pressure Gauges
6.5 Tap-Changing Equipment
6.6 Load Tap Changers
6.7 Voltage Regulating Transformers
6.8 Tap Changer Automatic Controls
6.9 Variable Phase Shifting Transformers
Reference
7 Reading and Applying Nameplate Information
7.1 Minimum Nameplate Requirements

7.2 Manufacturer’s Information
7.3 Cooling Class, Number of Phases, and Operating
Frequency
7.4 Voltage Ratings
7.5 KVA or MVA Ratings
7.6 Winding Connection Diagram
7.7 Phasor or Vector Diagram
7.8 Weights and Oil Capacity
7.9 Operating Pressure Range
7.10 Impedance
7.11 Basic Insulation Level
7.12 Nameplate Layout
References
8 Maintenance, Testing, Troubleshooting, and Reliability
8.1 Good Utility Practices

8.2 Preventative Maintenance versus Predictive
Maintenance

8.3 Factory Tests
8.4 Ratio Test
8.5 Other Factory Tests
8.6 Field Tests
8.7 Gas-in-Oil Analysis
8.8 Water-in-Oil Analysis
8.9 Drying Transformers
8.10 Oil Dielectric Test
8.11 Reliability Calculations
8.12 The Chi-Squared Distribution
8.13 The Poisson Distribution
8.14 Statistical Economics
References

1
Basic Transformer Theory
1.1 DEFINITION OF A TRANSFORMER

A transformer is ‘‘a static device consisting of a winding, or two or more
coupled windings, with or without a magnetic core, for inducing mutual cou-
pling between circuits. Note: Transformers are exclusively used in electric
power systems to transfer power by electromagnetic induction between cir-
cuits at the same frequency, usually with changed values of voltage and cur-
rent.’’ [1]
There are numerous types of transformers used in various applications
including audio, radio, instrument, and power. This book deals exclusively
with power transformer applications involving the transmission and distribu-
tion of electrical power. Power transformers are used extensively by traditional
electric utility companies, power plants, and industrial plants.
1.2 MAGNETIC UNITS AND CONVERSION

FACTORS
The basic operation of all transformers is deeply rooted in electromagnetics,
whether or not the transformer has a magnetic iron core. Students are often

confused by the terminology used to describe magnetic phenomena. Part of
the confusion lies in the different units of measurement that are used. There
are three basic systems of measurement used in engineering: English, MKS
(meter-kilogram-second), and cgs (centimeter-gram-second). To make matters
worse, some transformer textbooks even mix English units with cgs or MKS
units. For consistency and ease of understanding, this book will use MKS
units throughout the example problems.
The fist magnetic quantity is the magnetomotive force (MMF). In elec-
trical terms, MMF is roughly equivalent to the electromotive force (EMF),
that causes current to flow in an electrical circuit. The units and conversion
factors for MMF are
MKS: ampere-turn
cgs: gilbert
1 Gb ! 0.4π amp-turn
The next magnetic quantity is flux, represented by the Greek letter φ.

Since a magnetic field can be visualized as a bundle of lines flowing from a
north magnetic pole to a south magnetic pole, flux is the total number of
‘‘lines.’’ The units and conversion factors of φ are
MKS: weber
cgs: maxwell
1 Ma ! 1 line ! 10 "8 Wb
The magnetic flux density B is the concentration of magnetic of lines

across an area. The units and conversion factors for B are
MKS: tesla
cgs: gauss
1G! 10 "4 T
1T! 1 Wb/m 2
The magnetic field intensity H is the distribution of MMF along a mag-

netic path. If the flux density is constant, H is merely the total MMF divided
by the length of the magnetic path. The units and conversion factors for H
are
MKS: amp-turns/meter
cgs: oersted
1 Oe ! (250/π) amp-turns/m

1.3 CURRENTS AND MAGNETIC FIELDS
Consider the straight cylindrical conductor carrying a current i shown in Figure
1.1 A magnetic field surrounds the conductor. According to the right-hand
rule, a magnetic field surrounds the conductor in a counterclockwise direction.
The right-hand rule is stated as follows: With the thumb of the right hand
pointing in the direction of the electrical current, the fingers point in the direc-
tion of the magnetic field. When applying the right-hand rule, it is important
to use conventional electrical current and not the electron current.
For any closed path around the conductor with the incremental length
dl, in the direction of the magnetic field, the magnetic flux density, B is a
function of the current in the conductor according to the following equation:
! B ⋅ dl ! i # µ 0 (1.3.1)
where µ 0 is the vacuum permeability ! 4π # 10 "7 N/A 2.

For a straight conductor, the path of B around the conductor is always
circular, so at a distance r from the center of the conductor, the integral in
Eq. (1.3.1) is reduced to
! B ⋅ dl ! B # 2πr (1.3.2)
Therefore, the magnetic field intensity is inversely proportional to the distance

from the center of the conductor
µ0
B!i# (1.3.3)
2πr
FIGURE 1.1 B field surrounding a straight cylindrical conductor carrying a current i.

Example 1.1
A straight conductor carries a current of 100 A. What is the magnetic field
intensity at a distance of 25 cm from the center of the conductor?
In the MKS system, r ! 0.25 m. Using Eq. (1.3.3),
B ! 100 A # 4π # 10 "7 N/A 2 /(2π # 0.25 m) ! 8 # 10 "5 T
1.4 MAGNETIC INDUCTION

For a closed path in a magnetic field, the total flux φ is found by integrating
the incremental surface area dA times the normal component of the magnetic
field intensity B over any surface within the closed path:
φ! ! B ⋅ dA (1.4.1)
where
φ ! flux, Wb
dA ! incremental surface area, m 2
If the total flux is changing over time, there is an induced voltage E
around the closed path surrounding φ. The value E in volts is equal to "dφ/
dt, where the direction of E is in the right-hand sense. Figure 1.2 illustrates
this principle of magnetic induction. If the magnitude of B is decreasing, then
dφ/dt will be in the downward direction, and E will be in the positive in the
right-hand sense around the closed loop that encircles φ.
FIGURE 1.2 Voltage induced in a loop surrounding a time-varying B field.

1.5 CONSTRUCTING A SIMPLE
TRANSFORMER
From the foregoing discussion of the basic principles of magnetic induction,
it is not difficult to see how a rudimentary transformer could be constructed.
If a conductor carrying a changing current is brought near a second conductor,
then the changing magnetic flux surrounding the first conductor will be linked
to the second conductor and will induce a voltage. Such a rudimentary trans-
former is depicted in Figure 1.3.
An AC voltage is connected to a primary conductor, shown as the left-
hand solid bar in Figure 1.3. In response to the voltage, an AC current flows,
setting up a time-varying magnetic field surrounding the primary conductor.
A secondary conductor, shown as the right-hand solid bar, is located in prox-
imity to the primary conductor so that the magnetic flux surrounding the pri-
mary conductor links the secondary circuit. According to the law of induction,
there will be an induced voltage E around the path surrounding the time-
varying flux.
The configuration shown above is not very efficient in transferring en-
ergy because only a small portion of the total magnetic flux surrounding the
primary conductor will be linked to the secondary circuit. In order to improve
the efficiency of the rudimentary transformer, the magnetic field needs to be
channeled in such a way that most of the flux produced by the primary conduc-
tor is linked to the secondary circuit. This is accomplished by surrounding the
primary and secondary conductors with a magnetic core material having an
affinity for magnetic flux. This modification is shown in Figure 1.4. By adding
the magnetic core, essentially all of the magnetic flux produced in the primary
FIGURE 1.3 Voltage induced in a conductor.

FIGURE 1.4 Channeling a B field through a magnetic core.
conductor is linked to the secondary conductor. Therefore, the efficiency of

the rudimentary transformer is greatly increased.
Various types of core materials exist. The important physical property
is the permeability constant µ, given in units of N/A 2. The relative permeabil-
ity µ r is the permeability constant divided by the vacuum permeability µ 0 .
Values of µ r for some common magnetic core materials are as follows:
SiFe (unoriented) 400
SiFe (oriented) 1500
50–50 NiFe (oriented) 2000
79 Permaloy 12,000–100,000
A grain-oriented silicon steel conducts magnetic flux 1500 times better than
a vacuum. The advantages and disadvantages of grain-oriented steels will be
discussed in a later chapter.
The ratio of the flux density B and the field intensity H is equal to the
permeability of the medium µ:
B
µ! (1.5.1)
H
B
H! (1.5.2)
µ
1.6 THE MAGNETIC CIRCUIT

Since the magnetic core has been introduced, an understanding of the magnetic
circuit is necessary to quantify the relationships between voltage, current, flux,
and field density.

FIGURE 1.5 Closed magnetic circuit.
Consider the magnetic circuit shown in Figure 1.5 consisting of a coil

of wire wound around a magnetic yoke. The coil has N turns and carries a
current i. The current in the coil causes a magnetic flux to flow along the path
a-b-c-d-a. For the time being, let us assume that the flux density is small so
that the permeability of the yoke is a constant. The magnitude of the flux is
given by
φ ! N # i/! (1.6.1)
where N # i is the magnetomotive force (MMF) in ampere-turns and ! is
the reluctance of the magnetic circuit a-b-c-d-a.
As the name implies, reluctance is a property that resists magnetic flux
when MMF is applied to a magnetic circuit. Reluctance is roughly equivalent
to the resistance in an electrical circuit.
For a homogeneous material where the mean length of the flux path is
l and the cross-sectional area is A, the reluctance is calculated in the MKS
system of measurement as follows:
l
!! A 2 /J (1.6.2)
µ#A

The coil’s inductance L is equal to N 2 (µ # A)/l. Therefore, the coil’s induc-
tance is inversely proportional to reluctance of the magnetic circuit. For series
elements in the magnetic path, the total reluctance is found by adding the
values of reluctance of the individual segments along the magnetic path. The
reluctance values of parallel elements in a magnetic circuit are combined in
a manner similar to combining parallel resistances in an electrical circuit.
Example 1.2
In the magnetic circuit shown in Figure 1.6, the coil has 100 turns and carries
10 A. The relative permeability of the yoke is 10,000. The lengths of the
segments along the mean magnetic path are as follows:
Segments a-b and e-f ! 10 cm
Segments b-c and d-e ! 4 cm
Segment f-a ! 9 cm
Air gap ! 1 cm
The cross-sectional area of all segments is 4 cm 2. Find the flux φ and the flux
density B.
FIGURE 1.6 Magnetic circuit with an air gap.

Using the MKS system of measurement, the reluctance of the yoke is
!y:
2 # 0.10 m $ 2 # 0.04 m $ 0.09 m 0.0925 m "1
!y ! !
10,000µ 0 # 0.0004 m 2 µ0
The reluctance of the air gap is ! a :
0.01 m 25 m "1
!a ! !
µ 0 # 0.0004 m 2
µ0
The total reluctance ! T is found by adding ! y and ! a :
25.0925 m "1 25.0925
!T ! !y $ Ra ! ! A 2 /J
µ0 4π # 10 "7
The flux is found by dividing the MMF by the total reluctance:
i 10 "7
φ!N# ! 100 # 10 # 4π # Wb ! 5.008 # 10 "5 Wb
!t 25.0925
The flux density is found by dividing the flux by the cross-sectional area of
the magnetic path:
φ 10 "5 Wb
B! ! 5.008 # ! 0.1252 Wb/M 2
A 0.0004 M 2
The magnetic field intensity H is equal to the flux density B divided by the
permeability:
B
H!
µ
In the yoke,
0.1252
H! Wb/m 2
10,000 # µ 0
0.1252
! amp-turn/m
(10,000 # 4π # 10 "7)
! 9.963 amp-turns/m
In the air gap, µ ! µ 0 :
0.1252
H! amp-turns/m ! 9.963 # 10 4 amp-turns/m
4π # 10 "7

The magnetic field in the air gap sets up an attractive force that tends
to pull the pole pieces of the yoke together. The force F in the MKS system
of measurement is given by
B2 A
F! N (1.6.3)
2µ 0
For the magnetic circuit in this example the mechanical force across the air
gap is calculated from Eq. (1.6.3) as follows:
" #
2
0.1252 Wb 0.0004 m 2
F! # ! 2.49 N
m2 2 # 4π # 10 "7 A 2 /J
1.7 THE B-H CURVE

Up to this point, it was assumed that the core permeability is constant; i.e.,
B ! µ # H. For actual transformer core materials, the relationship between
B and H is much more complicated. For a flux that periodically changes, the
B-H curve depends on the magnitude of the flux density and the periodic
frequency. Figure 1.7 plots the B-H curve for a ferromagnetic core with a 60
Hz sinusoidal flux density having a moderate peak value.
The B-H curve is a closed loop with the path over time moving in a
counterclockwise direction over each full cycle. Note that when the magnetiz-
ing current is zero (H ! 0) there is still a considerable positive or negative
residual flux in the core. This residual flux is from crystalline structures in
ferromagnetic materials that remain magnetically aligned even after the MMF
is removed.
For a given peak amplitude of flux density, the B-H loop becomes nar-
rower at frequencies below 60 Hz, although the width of the loop is not directly
proportional to frequency. Even at very low frequencies approaching DC, the
B-H curve has a finite area contained in the loop.
As seen in Figure 1.7, magnetic materials are highly nonlinear, so treat-
ing m as a constant is clearly an oversimplification. Nevertheless, assuming
that materials are linear, at least over some range of flux density, is required
in order to do quantitative analysis.
As the peak amplitude of the flux increases, the core goes into satura-
tion; i.e., B increases at a much smaller rate with respect to increasing H. This
means that µ gets effectively smaller as B increases. In saturation, the slope
dB/dH is approximately equal to µ 0 . Figure 1.8 plots a typical B-H curve for
a ferromagnetic core with a 60 Hz sinusoidal flux density having a large peak

FIGURE 1.7 B-H curve for moderate flux density.
value. This core material saturates at approximately %1.5 Wb/m 2 (%1.5 T),
which is a typical saturation value for materials used in power transformers.
The magnitude of H increases greatly when the core goes into saturation,
meaning that the peak magnetizing current increases dramatically. Again, the
width of the B-H loop becomes narrower at frequencies below 60 Hz for a
given peak amplitude of flux.
1.8 THE B-H CURVE AND HYSTERESIS

Suppose coil having N turns of wire is wound around a magnetic core and
the coil conducts a time-varying current i. The current magnetizes the core,
inducing a voltage across each turn. The quantity of volts per turn in the MKS
system of measurement is given by
dφ
E/N ! " (1.8.1)
dt
If φ is expressed in cgs units, then the volts per turn will be 10 "8 times
this value. Note that the induced voltage per turn is the same for any turn of

FIGURE 1.8 B-H curve for large flux density.
wire wound around core, including the coil carrying the magnetizing current.
The voltage across the entire coil E is simply the volts per turn times the
number of turns.
dφ
E ! "N # (1.8.2)
dt
The minus sign indicates that the induced voltage tends to oppose the direction
of the current flow. The energy supplied to the coil from the electrical circuit
W is found by integrating the magnitude of the power supplied to the coil
over time. Since the power is equal to the voltage across the coil times the
current in the coil, and ignoring the electrical resistance of the coil,
W! ! E # i dt ! ! N # dφdt # i dt ! ! N # i dφ J (1.8.3)
Suppose the core has a mean length equal to l, and assume the core has
a uniform cross-sectional area equal to A.
N#i!H#l (1.8.4)

dφ ! A # dB (1.8.5)
Core volume in meter 3 ! A # l (1.8.6)
W ! (core volume in meter 3) # ! H dB J (1.8.7)
! H dB ! area contained in the B-H loop (1.8.8)
In the MKS system with a periodically changing current, the energy delivered
to the coil over each complete cycle is equal to the physical volume of the
core material times the area contained in the B-H loop. The energy supplied
to the coil is called hysteresis loss, which dissipates as heat in the core. It
results from a kind of ‘‘friction’’ that occurs when the magnetic domains of
the core material realign every half-cycle.
Example 1.3
A magnetic core has a uniform cross-sectional area and a total volume of 1
m 3. Given the graph of a 60 Hz B-H curve, as shown in Figure 1.9, estimate
the total hysteresis losses in watts for this core.
FIGURE 1.9 B-H curve used in Example 1–4.

Each of the dashed rectangles shown in Figure 1.9 represents 0.5 #
50 ! 25 J of energy per cubic meter of core material. The hysteresis loop
occupies roughly 9 rectangles equaling 225 J per cycle per cubic meter. At
60 Hz, there are 13,500 J dissipated per cubic meter every second, so the total
hysteresis losses are about 13.5 kW for a 1 m 3 core.
Example 1.4
Suppose a coil having 100 turns is wound on a core with a uniform cross-
sectional area of 0.25 m 2 and a mean path length of 4 m. Using the 60 Hz
hysteresis curve shown in Figure 1.9, what is the sinusoidal voltage that is
required to excite the core to the level shown in the figure, and what is the
peak magnetizing current?
From the B-H curve in Figure 1.9, the peak value of H is around 125
amp-turns/m and the peak value of B is around 1.5 Wb/m 2. The MMF is
found by multiplying H by the mean core length:
MMF ! 125 amp-turns m # 4 m ! 500 amp-turns

i ! MMF/N ! 500 amp-turns/100 turns ! 5 A (peak)
The flux is found by multiplying B by the cross-sectional area of the core:
φ ! B # A ! 1.5 # 0.25 Wb ! 0.375 Wb (peak)
For a frequency of 60 Hz,
φ ! 0.375 sin (377t) Wb

E ! "N dφ/dt ! "100 # 0.375 # 377 cos (377t) V
The root mean square (RMS) voltage is found by multiplying the magni-
tude of E times 0.707:
E RMS ! 100 # 0.375 # 377 # 0.707 ! 9995 V
The apparent power supplied to the coil is the RMS voltage times the RMS
current. If the magnetizing current were purely sinusoidal, then i RMS ! 5 #
0.707 A ! 3.535 A and the apparent power would be 9995 # 3.535 ! 35.332
KVA. Remembering that the hysteresis losses found in Example 1.3 were
13.5 kW, the power factor of the load supplied to the coil is around 38%.
In reality, however, the magnetizing current cannot be assumed to be purely
sinusoidal, as will be seen in the next section.

1.9 MAGNETIZING CURRENTS
AND HARMONICS
The B-H curve can be used to construct the wave shape of the magnetizing
current from the wave shape of the excitation voltage. Figure 1.10 illustrates
the technique. First, the integral of the exciting voltage divided by N # A is
plotted along the horizontal axis. In this case, the exciting voltage is assumed
to be sinusoidal so its integral is cosinusoidal. The integral of E is divided by
(N # A) to obtain B.
Each point on the B cosine curve is projected onto a point on a curve
along the vertical axis, using the B-H curve to determine the horizontal dis-
tance from the vertical axis. Some of these projections are indicated by the
dotted lines below. The value of H corresponding to this point is multiplied
by the mean length of the core to obtain the magnetizing current i. It is clearly
seen from this example that that the magnetizing current is not sinusoidal.
A Fourier analysis of magnetizing current shows a 60 Hz fundamental
and the presence of odd harmonics. Generally speaking, the harmonic content
of the magnetizing current increases as the level of excitation increases, espe-
cially as the core goes into saturation. For a moderate flux density of 12 KG,
the percent harmonic content of the exiting current is shown in Table 1.1.
FIGURE 1.10 Developing the plot of magnetizing current from a B-H curve.

TABLE 1.1 Harmonic Content of the Exciting Current for a Moderate Level
of Excitation
Harmonic 3rd 5th 7th 9th 11th

Content present in exciting current, % 20 6 2 0.7 0.3
Source. Ref. 2.
The predominant harmonic is the third (180 Hz), although the higher-
order harmonics are strong enough to cause telephone interference problems
in circuits in proximity to power lines. The presence of third harmonics in an
electric power system can also cause equipment to overheat and produce volt-
age distortion. The isolation of third harmonics is an important design consid-
eration in transformers. Techniques to accomplish this are covered in later
chapters.
1.10 TRANSFORMER CORE DESIGN

AND CONSTRUCTION
As we have seen in Example 1.2, air gaps in a magnetic core will add consider-
able reluctance to the magnetic circuit. Remembering that the inductance of
a coil and the magnetic reluctance are inversely proportional, air gaps reduce
the inductance of the coil and increase the magnitude of magnetizing currents.
In practical transformers, we want to reduce magnetizing currents to almost
negligible levels; it is therefore important to eliminate all air gaps if possible.
One approach would be to make the core from a solid block of material. This
is impractical from the standpoint of fabricating the transformer, since the
coils would have to be wound through the core window.
Also, since metallic core materials conduct electric current as well as
magnetic flux, the induced voltages would produce large circulating currents
in a solid core. The circulating currents would oppose the changing flux and
effectively ‘‘short out’’ the transformer.
A practical solution is to fabricate the core from thin laminated steel
sheets that are stacked together and to coat the surfaces of the laminations
with a thin film that electrically insulates the sheets from each other. Steel
not only has excellent magnetic properties but is also relatively inexpensive
and easy to fabricate into thin sheets.
In a modern transformer plant, steel ribbon is cut into sections by a
cutting/punching machine commonly called a Georg machine. The sizes and
shapes of the sections are determined by the core design of the individual

transformer. The thickness of the sheets varies somewhat; core laminations
operating at 60 Hz are between 0.010 and 0.020 in. thick, with 0.012 in. being
the most common thickness in use today.
Different methods of stacking core steel have been used in the past. One
such method is called the butt lap method using rectangular core sections and
is illustrated in Figure 1.11 Even if the edges of the segments do not butt
together perfectly, as shown in the exaggerated edge view at the bottom of
the figure, the alternating even and odd layers assure that the magnetic flux
has a continuous path across the surfaces of the adjacent layers. The type of
construction depicted above works best with core steel that is not grain or-
iente, i.e., where permeability does not depend on the direction of the flux
through the steel.
One of the greatest contributions to transformer efficiency and low cost
was the introduction of grain-oriented steel in the 1940s. Grain-oriented steel
is a silicon-iron alloy that is rolled or ‘‘worked’’ during fabrication in such
a way that the permeability is higher and the hysteresis losses are lower when
the flux is in the direction of the ‘‘grain.’’ Unfortunately, the properties of
this steel for a flux that goes ‘‘against the grain’’ are much worse than the
non-grain-oriented steel. Therefore, the design of the core has to take this into
account. When using grain-oriented steel, the lamination sections are mitered
at a 45° angle so that when the flux changes direction by 90°, it more or less
FIGURE 1.11 Stacking a laminated core using butt lap construction.

FIGURE 1.12 Flux transition at the corner of a mitered core.
still follows the grain of each of the segments. Figure 1.12 depicts a corner
overlap using core sections with 45° mitered edges. The grain of the steel
is oriented along the length of the laminations in the horizontal and vertical
directions. The flux is at a 45° angle to the grain at the mitered edges. Alternate
layers are cut into slightly different lengths and their corners have slightly
different shapes. The modern multistep layer method uses up to five layers of
differently shaped sections. This method is illustrated in Figure 1.13 with the
first three layers exploded to show the stacking sequence.
The cross section of a transformer core can either be square or rectangu-
lar; however, a round shape is used in most large transformers of the so-called
core form design, where the coils have a round cross section. With a round core
within round coils, the use of space and materials is more efficient. Attaining a
round cross section with thin steel laminations is not that difficult, although
this complicates the design. The design engineer is usually content with ap-
proximating a circular core, as shown schematically in Figure 1.14. Note that
the actual laminations are too thin to show individually. The empty spaces
between the core and the circular coil are filled with wooden dowels or other
spacer materials to improve the mechanical strength of the transformer. Chap-
ter 5 will include a discussion of the mechanical forces that occur under fault
conditions.

FIGURE 1.13 Successive layers of a laminated core using mitered construction.
FIGURE 1.14 Development of a circular cross-sectional core.

1.11 MAGNETOSTRICTION
One of the major problems with large power transformers is audible noise
that can be loud enough to be very annoying. Essentially all transformer noise
is due to a phenomenon called magnetostriction. When a strip of steel is mag-
netized, it contracts very slightly. At the flux densities used in large power
transformers, the amount of magnetostriction is only about 60 µ per meter of
length. For a 60 Hz transformer, this small change in dimension occurs 120
times per second. Due to the fact that magnetostriction is not linear with re-
spect to the flux density B there are also harmonics of 120 Hz present in the
noise. If any part of the transformer is in resonance with any of the harmonics,
the noise can be amplified hundreds of times. Therefore, part of the core design
and the overall transformer design is an analysis of the resonant frequencies.
1.12 COMPLETING THE TRANSFORMER

BY ADDING A SECOND WINDING
We are now prepared to complete our prototype transformer by adding a sec-
ond winding. It should now be apparent that by coiling the primary conductor
around the core using many turns, a considerable voltage can be induced with
only a tiny magnetizing current if the peak flux density is kept below the
saturation value. Now suppose a secondary coil is wound around the same
core, surrounding the same magnetic flux as the primary coil as shown in
Figure 1.15. Since the secondary coil encircles the same flux as the primary
FIGURE 1.15 Transformer with a primary and secondary winding.

coil, the induced voltage per turn is the same in both the primary and secondary
coils. Let E p ! applied primary voltage, E s ! induced secondary voltage,
N p ! number of primary turns, and N s ! number of secondary turns. Since
the induced voltage in the primary coil equals the applied voltage and since
the induced volts per turn is the same for both primary and secondary,
Ep E
! s (1.12.1)
Np Ns
Ep Np
! (1.12.2)
Es Ns
Equation (1.12.2) is the first transformer law. The ratio N p /N s is called the
transformer turns ratio, or TTR. Now suppose a load resistance is connected
to the secondary coil, as shown in the Figure 1.16. The arrows indicate the
directions of the primary and secondary currents. The secondary voltage
causes current in the secondary to flow in a direction that always tends to
cancel flux in the core. This tendency to cancel flux reduces the induced volt-
ages in both the primary and secondary coils. With a reduction in the induced
voltage in the primary, the applied voltage across the primary winding in-
creases the primary current to restore the flux to its original value. Equilibrium
is established when the total MMF is just sufficient to induce a voltage equal
to the voltage applied across the primary coil. This is equal to the magnetizing
MMF:
FIGURE 1.16 Two-winding transformer with a load connected to the secondary

winding.

MMF primary $ MMF secondary ! MMF magnetizing (1.12.3)
With substantial currents flowing in both the primary and secondary
winding under load, the magnetizing MMF is negligible compared to the pri-
mary MMF and secondary MMF:
MMF primary $ MMF secondary ! 0 (1.12.4)
Np # ip $ Ns # is ! 0 (1.12.5)
i p "N s
! (1.12.6)
is Np
The minus sign in Eq. (1.12.6) indicates that the currents in the primary and
secondary windings are in opposite directions with respect to producing mag-
netic flux in the core. While this is undeniably true, the minus sign can be
dropped in order to express the ratio of primary current to secondary current.
ip N
! s (1.12.7)
is Np
Equation (1.12.7) is the second transformer law. By multiplying E p /E s
from the first law by i p/ i s from the second law,
Ep # ip Np # Ns
! !1 (1.12.8)
Es # is Ns # Np
(E # i) p ! (E # i) s (1.12.9)
The meaning of Eq. (1.12.9) is that the instantaneous power supplied to the
primary coil from the applied voltage equals the instantaneous power supplied
by the secondary coil to the load; in other words, power in ! power out.
The transformer laws are true irrespective of the phase angles of the currents.
Therefore, the real power, reactive power, and apparent power of the primary
circuit are all equal to the real power, reactive power, and apparent power of
the secondary circuit.
1.13 PLACEMENT OF THE WINDINGS

Schematically, we have depicted the primary and secondary windings as being
wound around a common core but located on opposite core legs. In the Chapter
2 we will discuss two very different types of transformers, namely, the core
form and the shell form designs. In any transformer design, however, the pri-

FIGURE 1.17 Cross section of a transformer with primary and secondary windings
on a common circular core leg.
mary and secondary windings are always mounted in close proximity to each
other in order to maximize the mutual coupling between the windings and
thereby increase the overall efficiency. Figure 1.17 illustrates part of a two-
winding core form transformer as a cut away view from the side and the end.
This configuration has one set of low-voltage and high-voltage windings
mounted over a vertical core leg. Note that the core leg and the top and bottom
core yokes are stepped to approximate a circular cross section. The laminations
are too thin to be seen individually in the edge view. By convention, the HV
winding is usually called the primary and the LV winding is called the second-
ary; however, either the HV or the LV winding can be the input winding.
So far, we have discussed the relationships between voltages and cur-
rents for only one pair of primary and secondary windings. In Chapter 2 we
will discuss the various. winding connections and transformer configurations
with multiple sets of windings used in three-phase and two-phase systems.
Example 1.5
A two-winding transformer has a primary winding with 208 turns and a sec-
ondary winding with 6 turns. The primary winding is connected to a 4160V
system. What is the secondary voltage at no load? What is the current in the
primary winding with a 50-amp load connected to the secondary winding?
What is the apparent power flowing in the primary and secondary circuits?

First transformer law:
E p N p 208
! !
Es Ns 6
E p ! 4160 V
6
E s ! 4160 V # ! 120 V
208
Second transformer law:
ip N 6
! s!
is N p 208
i s ! 50 A
6
i p ! 50 A # ! 1.44 A
208
Apparent power in primary circuit ! Ep # Ip
! 4160 V # 1.442 A ! 5999 VA
Apparent power in secondary circuit ! 120 V # 50 A ! 6000 VA
REFERENCES
1. Institute of Electrical and Electronics Engineers, Inc. IEEE Standard Dictionary
of Electrical and Electronics Terms, IEEE Std. 100-1972.)
2. R. L. Bean, N. Chackan, Jr., H. R. Moore, and E. C. Wentz. Transformers for the
Electric Power Industry. McGraw-Hill, New York, 1959, p. 97.

2
Two-Winding Transformer
Connections
2.1 INTRODUCTION
Modern electrical systems are almost exclusively three-phase systems, not-
withstanding the many miles of distribution circuits that are configured as
single-phase taps off of these systems. In addition, there still exist remnants
of two-phase systems (typically in mining operations) that were fairly common
years ago. When two polyphase systems have different voltages and/or phase
angles, these systems can be interconnected using transformers having various
possible types of connections. Any one of these connections can be accom-
plished either with a bank of single-phase transformers or by a single poly-
phase transformer. As we shall see in this chapter, it is in fact possible to
interconnect two polyphase systems having a different number of phases using
special transformer connections.
A single-phase two-winding transformer is nothing more than a primary
and a secondary winding wound around the same magnetic core. Single-phase
two-winding transformers can be used in either single-phase circuits or poly-
phase circuits. A polyphase two-winding transformer contains a number of
sets of primary and secondary windings. Each set wound around a separate
magnetic core leg. A three-phase two-winding transformer has three sets of

primary and secondary windings, and a two-phase two-winding transformer
has two sets of primary and secondary windings.
Chapter 1 described the basic theory of operation of a two-winding trans-
former, and the transformer laws were developed. In this chapter, the princi-
ples of the two-winding transformer are applied to polyphase systems. As we
shall see, there are a number of possible ways two-winding transformers can
be connected to polyphase systems and a number of possible ways that poly-
phase two-winding transformers can be constructed.
2.2 THE Y-Y CONNECTION IN

THREE-PHASE SYSTEMS
The most obvious way of transforming voltages and currents in a three-phase
electrical system is to operate each phase as a separate single-phase system.
This requires a four-wire system comprised of three phase wires plus a com-
mon neutral wire that is shared among the three phases. Each phase is trans-
formed through a set of primary and secondary windings connected phase-to-
neutral. This is commonly referred to as the Y-Y connection, as illustrated
in Figure 2.1. The left-hand part of Figure 2.1 shows the physical winding
connections as three separate two-winding transformers. Both the primary and
secondary windings of each of these transformers are connected between one
FIGURE 2.1 Y-Y transformer connection and vector diagram.

phase, labeled A, B, and C, and the neutral, labeled N. The right-hand part of
Figure 2.1 shows the winding connections as a vector diagram. The direction
of the phase rotation is assumed to be A-B-C expressed in a counterclockwise
direction. This means that when the vector diagram rotates in a counterclock-
wise direction on the page, a stationary observer sees A phase, followed by
B phase, and followed by C phase in sequence. This counterclockwise conven-
tion will be followed throughout this book.
The term ‘‘Y-Y connection’’ should be obvious from the fact that the
vector diagrams of the primary and secondary windings both resemble the
letter Y. Each phase of the primary and secondary circuits is 120 electrical
degrees out of phase with the other two phases. This is represented by angles
of 120° between the legs of the primary Y and the secondary Y in the vector
diagram. Each primary winding is magnetically linked to one secondary wind-
ing through a common core leg. Sets of windings that are magnetically linked
are drawn parallel to each other in the vector diagram. In the Y-Y connection,
each primary and secondary winding is connected to a neutral point. The neu-
tral point may or may not be brought out to an external physical connection
and the neutral may or may not be grounded.
As we saw in Chapter 1, transformer magnetizing currents are not purely
sinusoidal, even if the exciting voltages are sinusoidal. The magnetizing cur-
rents have significant quantities of odd-harmonic components. If three identi-
cal transformers are connected to each phase and are excited by 60 Hz voltages
of equal magnitude, the 60 Hz fundamental components of the exciting cur-
rents cancel out each other at the neutral. This is because the 60 Hz fundamen-
tal currents of A, B, and C phase are 120° out of phase with one another and
the vector sum of these currents is zero. The third, ninth, fifteenth and other
so-called zero-sequence harmonic currents are in phase with each other; there-
fore, these components do not cancel out each other at the neutral but add in
phase with one another to produce a zero-sequence neutral current, provided
there is a path for the neutral current to flow.
Due to the nonlinear shape of the B-H curve, odd-harmonic magnetizing
currents are required to support sinusoidal induced voltages. If some of the
magnetizing current harmonics are not present, then the induced voltages can-
not be sinusoidal. If the neutrals of both the primary and the secondary are
open-circuited and there is no path for the zero-sequence harmonic currents
to flow, the induced voltages will not be sinusoidal.
Figure 2.2 depicts the situation where the primary neutral is returned to
the voltage source in a four-wire three-phase circuit. Each of the magnetizing
currents labeled i A , i B , and i C contain the 60 Hz fundamental current and all
of the odd harmonic currents necessary to support sinusoidal induced voltages.

FIGURE 2.2 Y-Y Connection with the primary neutral brought out.
The zero-sequence magnetizing currents combine to form the neutral current

i N , which returns these odd harmonics to the voltage source. Assuming that
the primary voltage is sinusoidal, the induced voltages E A , E B , and E C (in both
the primary and secondary) are sinusoidal as well.
This situation changes dramatically if the neutrals of both sets of the
primary and secondary windings are open-circuited, as shown in Figure 2.3.
FIGURE 2.3 Voltage at the primary neutral of a Y-Y connection with the primary
and secondary neutrals isolated.

Even if the source voltages E A , E B , and E C are purely sinusoidal, the induced
voltages E′A , E′B , and E′C will not be sinusoidal. This results in distortions of
the secondary voltages. The resulting voltage distortion is equivalent to a Y-
Y transformer with zero-sequence currents allowed to flow in the primary
neutral with an imaginary superimposed primary winding carrying only the
zero-sequence currents 180° out of phase with the normal zero-sequence cur-
rents (see Ref. 1). Analysis of the voltages induced by the ‘‘phantom primary
windings’’ is greatly complicated by the fact that the core is highly nonlinear
so that each of the individual zero-sequence harmonics currents carried by the
phantom primary windings will induce even higher-order harmonic voltages
as well.
Fourier analysis can be used to arrive at an approximation of the second-
ary voltages with an open primary neutral. Taking one phase at a time, the
normal magnetizing current for a sinusoidal exciting voltage is plotted from
the B-H curve of the transformer using the technique outlined in Chapter 1.
The normal magnetizing current is converted to a Fourier series and then it
is reconstructed by removing all of the zero-sequence harmonics. The resulting
exciting current will have a shape different from the normal exciting current,
which is then used to construct an induced voltage using the B-H curve in the
reverse manner that was used to construct the original exciting current. This
process is rather laborious, so suffice it to say that if a Y-Y transformer does
not have a neutral path for zero-sequence exciting currents, there will be har-
monic voltages induced in the secondary even if the exciting voltage is purely
sinusoidal.
Another problem with a Y-Y connection is that if an unbalanced phase-
to-neutral load is connected to the secondary, the phase voltages at the load
will be unbalanced also unless the neutral of the load is connected to the
secondary neutral of the transformer. Therefore, it is generally a good practice
to bring out and ground both the primary and the secondary neutrals in a Y-Y
transformer connection.
2.3 ADVANTAGES OF THE Y-Y CONNECTION

Although care must be exercised when using the Y-Y connection, this connec-
tion has certain inherent and important advantages over other three-phase
transformer connections.
1. The primary and secondary circuits are in phase; i.e., there are no
phase angle displacements introduced by the Y-Y connection. This
is an important advantage when transformers are used to intercon-
nect systems of different voltages in a cascading manner. For exam-

ple, suppose there are four systems operating at 500, 230, 138, and
69 kV that need to be interconnected. Substations can be constructed
using Y-Y transformer connections to interconnect any two of these
voltages. The 500 kV system can be tied with the 69 kV system
through a single 500 to 69 kV transformation or through a series
of cascading transformations at 230, 138, and 69 kV.
2. Since the phase-to-neutral voltage is only 57.7% of the phase-to-
phase voltage, the windings of a Y-Y transformer require fewer
turns to produce the same level of excitation in the core compared
to windings connected across the phases.
3. If the neutral end of a Y-connected winding is grounded, then there
is an opportunity to use reduced levels of insulation at the neutral
end of the winding. A winding that is connected across the phases
requires full insulation throughout the winding.
4. A Y-Y transformer may be constructed as an autotransformer, with
the possibility of great cost savings compared to the two-winding
transformer construction. (Chapter 4 will fully develop the topic of
autotransformers.)
2.4 DISADVANTAGES OF THE Y-Y

CONNECTION
The Y-Y transformer connection was poorly understood in the early days of
power engineering and it received a very bad reputation when it was first used;
in fact, this connection was avoided for a long time until its limitations were
overcome by good engineering practice. Some of the inherent disadvantages
of the Y-Y connection are discussed below:
1. The presence of third (and other zero-sequence) harmonics at an
ungrounded neutral can cause overvoltage conditions at light load.
When constructing a Y-Y transformer using single-phase transform-
ers connected in a bank, the measured line-to-neutral voltages are
not 57.7% of the system phase-to-phase voltage at no load but are
about 68% and diminish very rapidly as the bank is loaded. The
effective values of voltages at different frequencies combine by tak-
ing the square root of the sum of the voltages squared. With sinusoi-
dal phase-to-phase voltage, the third-harmonic component of the
phase-to-neutral voltage is about 60%, so the effective voltage
across the winding is calculated as follows:
E ! [0.577 2 " (0.6 # 0.577) 2] 1/2 ! 68%

2. There can be a large voltage drop for unbalanced phase-to-neutral
loads. This is caused by the fact that phase-to-phase loads cause a
voltage drop through the leakage reactance of the transformer
whereas phase-to-neutral loads cause a voltage drop through the
magnetizing reactance, which is 100 to 1000 times larger than the
leakage reactance. (The subject of leakage reactance will be dis-
cussed in Chapter 3.)
3. Under certain circumstances, a Y-Y connected three-phase trans-
FIGURE 2.4 Overvoltage condition produced by a fault at the primary of a Y-Y

connection.

former can produce severe tank overheating that can quickly destroy
the transformer. This usually occurs with an open phase on the pri-
mary circuit and load on the secondary. (The tank heating phenome-
non will be discussed at length in Chapter 5.)
4. Series resonance between the third harmonic magnetizing reactance
of the transformer and line-to-ground capacitance can result in se-
vere overvoltages. (This phenomenon, called ferroresonance, will
be discussed in Chapter 5.)
5. If a phase-to-ground fault occurs on the primary circuit with the
primary neutral grounded, then the phase-to-neutral voltage on the
unfaulted phases increases to 173% of the normal voltage. This
would almost certainly result in overexcitation of the core, with
greatly increased magnetizing currents and core losses. This is illus-
trated in Figure 2.4. A bold X marks the location of a B phase-to-
ground fault with the neutral of the voltage source either un-
grounded or connected to ground through a large impedance. The
voltage across the B phase winding collapses and the applied volt-
ages across the A phase and C phase windings are now equal in
magnitude to the phase-to-phase voltages.
6. If the neutrals of the primary and secondary are both brought out,
then a phase-to-ground fault on the secondary circuit causes neutral
fault current to flow in the primary circuit. Ground protection re-
FIGURE 2.5 Primary neutral current for a fault on the secondary side of a Y-Y con-
nection.

laying in the neutral of the primary circuit may then operate for
faults on the secondary circuit. This is illustrated in the Figure 2.5.
The two magnetically coupled windings are connected by a dotted
line. Any fault current in the secondary neutral is transformed into
neutral current in the primary circuit through the second transformer
law.
The obvious remedy for some of the disadvantages of the Y-Y trans-
former connection would be to simply solidly ground both the primary and
secondary neutrals. In fact, this is standard practice for virtually all Y-Y trans-
formers in systems designed by utility companies. Unfortunately, solidly
grounding the neutrals alone does not solve the problem of tank overheating,
ferroresonance, and operating primary ground protection during secondary
faults.
2.5 THE Y-∆ CONNECTION AND THE ∆-Y

CONNECTION
Connecting the primary or secondary winding across the phases of a three-
phase transformer can eliminate many of the major drawbacks of the Y-Y
connection. A winding connected phase-to-phase is called a delta-connected
winding because of its resemblance to the Greek letter ∆ when it is depicted
in a vector diagram. Since a ∆ winding has no connection to its neutral point,
it is usually left ungrounded, so it ‘‘floats’’ above ground potential. The ∆-Y
connection is shown in Figure 2.6.
The left-hand part of Figure 2.6 shows the physical winding connections
as a set of two-winding transformers. The primary winding of each transformer
is connected phase-to-phase and the secondary of each transformer is con-
nected phase-to-neutral with the neutrals grounded. The right-hand part of
Figure 2.6 shows the winding connections shown as a vector diagram. As
usual, the direction of phase rotation is assumed to be A-B-C in a counterclock-
wise direction.
One of the major advantages of the ∆-Y connection is that it provides
harmonic suppression. Recall that the magnetizing current must contain odd
harmonics for the induced voltages to be sinusoidal and the third harmonic is
the dominant harmonic component. In a three-phase system the third harmonic
currents of all three phases are in phase with each other because they are zero-
sequence currents. In the Y-Y connection, the only path for third harmonic
current is through the neutral. In the ∆-Y connection, however, the third har-
monic currents, being equal in amplitude and in phase with each other, are

FIGURE 2.6 ∆-Y transformer connection and vector diagram.
able to circulate around the path formed by the ∆-connected winding. The
same thing is true for the other zero-sequence harmonics.
If the magnetizing current waveforms of all three phases have approxi-
mately the same shape and magnitude, and if the phase angles of the 60 Hz
fundamental frequencies are 120° apart, then the third harmonic currents circu-
late only within the transformer bank and do not emerge as physical currents
at the terminals of the windings. This causes these currents to be suppressed
in the primary and secondary circuits. Typical transformer magnetizing cur-
rents for the three different phases are plotted in Figure 2.7. The magnetizing
FIGURE 2.7 Three-phase excitation current wave forms (solid) and the third har-
monic components combined (dotted).

currents of the three phases are plotted by the heavy lines. For excitation at
60 Hz, the three magnetizing currents are separated in time by 1/180 of a second.
The phase angles of the 60 Hz fundamental frequencies are electrically by
120°. In the ∆ winding, the third harmonic currents of the three waveforms
in phase with each other and add algebraically to form the wave form shown
in Figure 2.7 as the dotted line with the sinusoidal shape. The combined third
harmonic current is plotted true to scale.
Another important advantage of the ∆-Y connection is that it provides
ground current isolation between the primary and secondary circuits. Assum-
ing that the neutral of the Y-connected secondary circuit is grounded, a load
connected phase-to-neutral or a phase-to-ground fault produces two equal and
opposite currents in two phases in the primary circuit without any neutral
ground current in the primary circuit. Therefore, in contrast with the Y-Y
connection, phase-to-ground faults or current unbalance in the secondary cir-
cuit will not affect ground protective relaying applied to the primary circuit.
This feature enables proper coordination of protective devices and is a very
important design consideration.
A transformer-connected ∆-Y with the neutral of the Y grounded is
sometimes referred to as a grounding bank, because it provides a local source
of ground current at the secondary that is isolated from the primary circuit.
For example, suppose an ungrounded generator supplies a simple radial system
through a ∆-Grounded Y transformer as shown Figure 2.8. The generator can
supply a single-phase-to-neutral load through the ∆-grounded Y transformer.
Let us refer to the low-voltage generator side of the transformer as the second-
ary and the high-voltage load side of the transformer as the primary. Note that
each primary winding is magnetically coupled to a secondary winding. The
magnetically coupled windings are drawn in parallel to each other in Figure
FIGURE 2.8 Ungrounded generator connected to a single-phase load through a

∆-Y transformer.

2.8. Through the second transformer law, the phase-to-ground load current in
the primary circuit is reflected as a current in the A-C secondary winding. No
other currents are required to flow in the A-C or B-C windings on the generator
side of the transformer in order to balance ampere-turns.
The ∆-Y transformer connection is used universally for connecting generators
to transmission systems because of two very important reasons. First of all,
generators are usually equipped with sensitive ground fault relay protection.
The ∆-Y transformer is a source of ground currents for loads and faults on the
transmission system, yet the generator ground fault protection is completely
isolated from ground currents on the primary side of the transformer. Second,
rotating machines can literally be shaken apart by mechanical forces resulting
from zero-sequence currents. The ∆-connected winding blocks zero-sequence
currents on the transmission system from the generator.
2.6 PHASE ANGLE DISPLACEMENT

AND PHASE ROTATION
A careful examination of the primary and secondary voltage vectors in Figure
2.6 reveals that in a ∆-Y connection the primary voltage of any given phase
is displaced electrically by 30° from the secondary voltage of the correspond-
ing phase. The 30° phase angle displacement may either be positive or nega-
tive; i.e., the primary voltage may either lead the secondary voltage by 30°
or lag the secondary voltage by 30° depending on how the transformer is
connected. The standard connection for a ∆-Y transformer is to have the high-
side voltages lead the low-side voltages by 30°, as shown in Figure 2.9. A
dotted line is shown connecting the A phase connection of the ∆ to an imagi-
nary neutral point within the ∆. This neutral point is not a physical connection.
With the usual A-B-C counterclockwise phase rotation, the primary voltage,
labeled A, leads the secondary voltage, labeled a, by an angle of 30° as shown
by the small vector diagram at the bottom of the figure.
The property of a ∆-Y transformer that causes the primary and secondary
voltages to be out of phase with each other is referred to as the phase angle
displacement of the transformer. Phase angle displacement must not be con-
fused with phase rotation. Phase rotation is the order in which the phase volt-
ages reach their peak values. In three-phase systems, the phase rotation can
be either A-B-C or C-B-A. The phase rotation can be reversed by interchanging
any two phases of the primary circuit or any two phases of the secondary
circuit. Interchanging two phases on both the primary circuit and the second-
ary circuit will revert back to the original phase rotation.

FIGURE 2.9 Phase angle displacement in a ∆-Y transformer.
Interchanging the phase connections in a ∆-Y transformer not only re-

verses the phase rotation but changes the phase angle displacement from a
standard $30° displacement to a "30° displacement, as illustrated in Figure
2.10. The upper part of the figure shows a ∆-Y transformer with the primary
terminals labeled 1, 2, and 3 and the secondary terminals labeled 1′, 2′, and 3′.
Suppose A phase is connected to terminal 1, B phase is connected to terminal 2,
and C phase is connected to terminal 3. Since the transformer has a standard
phase displacement, the primary leads the secondary by 30° for an A-B-C, 1–
2-3 phase rotation. Suppose A phase and C phase are interchanged on both
the primary and the secondary sides of the transformer, which retains the origi-
nal A-B-C phase rotation at the secondary. The transformer is not physically
altered; however, in order to produce an A-B-C, 3-2-1 phase rotation and retain
the convention of a counterclockwise vector rotation used throughout this
book, the vector diagram of the transformer must be redrawn as the mirror
image of the vector diagram of the transformer with a 1-2-3 phase rotation.
This mirror image is shown in the lower part of Figure 2.10. Note that
the relationships between the three sets of windings has not changed electri-
cally or magnetically in the mirror image. In other words, the 1-3 winding is
still magnetically linked to the 1′-N winding, the 2-1 winding is still magneti-
cally linked to the 2′-N winding, and the 3-2 winding is still magnetically

FIGURE 2.10 Phase angle displacements of a ∆-Y transformer for a 1-2-3 phase
rotation and a 3-2-1 phase rotation.
linked to the 3′-N winding in exactly the same way. What has changed, how-
ever, is the phase angle displacement between the primary and the secondary
circuits. The primary circuit now lags the secondary circuit by 30° with the
conventional counterclockwise rotation. Careful attention to phase angle dis-
placement is important; otherwise potentially disastrous results can occur. This
is illustrated by the following example, which was based on an actual case.
Example 2.1
A certain major utility company, named TransCo, supplied power to a small
municipal distribution company, named DisCo. The DisCo substation has
standard ∆-Y connected transformers. Both TransCo and DisCo had an A-B-C
phase rotation. The voltages on the DisCo distribution system lagged TransCo
transmission voltages by 30° due to the phase displacement of the ∆-Y trans-
formers.
TransCo is directly interconnected with another major utility company,
named WireCo. The phase rotation of WireCo is C-B-A throughout its trans-
mission and distribution systems. Nevertheless, the TransCo and WireCo

transmission systems are interconnected at various places, simply by swapping
the phases labeled A and C at the point of interconnection, reversing the phase
rotations at the points of interconnection. WireCo supplies its own distribution
system through substations that have standard ∆-Y transformers. Because of
the nonstandard C-B-A, 3-2-1 phase rotation, however, WireCo’s distribution
system voltages lead its transmission system voltages by 30°.
Many years go by and WireCo purchases the small municipal distribu-
tion company, DisCo. WireCo plans to run a transmission line to supply Dis-
Co’s substation, and disconnect the transmission line from TransCo. Because
DisCo has an A-B-C phase rotation, whereas all of WireCo has a C-B-A phase
rotation, it was recognized that some kind of a phase swap must be made in
order to maintain the A-B-C phase for DisCo’s distribution customers. There
was also a future plan to integrate the DisCo distribution system with the
WireCo distribution system by building distribution ties between the two sys-
tems. The fact that DisCo had an A-B-C phase rotation while WireCo had a
C-B-A phase rotation was not seen as a problem, since phase rotations can be
reversed simply by swapping two phases.
The big day arrived when DisCo’s transmission supply was converted
from the original supplier TransCo to the new supplier WireCo. Figure 2.11
shows the configuration that WireCo installed to accomplish the conversion.
The A and C phases of WireCo’s transmission line were swapped at the high-
voltage side of the ∆-Y transformers in DisCo’s substation. This provided the
proper A-B-C phase rotation for DisCo’s customers, but it was later realized
that no amount of phase swapping would accomplish interconnecting DisCo’s
FIGURE 2.11 Improper connections resulting in a 60° phase displacement between

distribution systems.

FIGURE 2.12 Proper connections resulting in 0° phase displacement between distri-
bution systems.
distribution system with WireCo’s distribution system, making it impossible

to fully integrate the two systems. What had gone wrong?
It is clear by studying the vector relationships in Figure 2.11 that there
is a permanent 60° phase angle displacement between the DisCo and WireCo
distribution systems. This happened because both standard and nonstandard
transformer connections were used at the substations. In order to properly tie
together the two systems, WireCo should have connected its transmission lines
to the transformers at DisCo’s substation in the same way as the connections
are made at WireCo’s substations, as depicted in Figure 2.12.
The connections shown in Figure 2.12 would have resulted in 3–2-1
rotations for both sets of transformers, and also the same phase displacements.
To provide the required A-B-C phase rotation for DisCo’s distribution system,
A and C phases could be swapped at the low side connections to the DisCo
substation transformers. The resulting voltages would now be in-phase with
WireCo’s distribution system, albeit with a reverse phase rotation. Now all
that is required to interconnect the DisCo and WireCo distribution systems is
to swap the phases labeled A and C at the point of interconnection.
2.7 THE Y-∆ GROUNDING BANK

There are times when a grounded Y-∆ transformer is used for no other purpose
than to provide a good ground source in an otherwise ungrounded system.
Take, for example, a distribution system supplied by a ∆-connected (i.e., un-
grounded) power source. If it is required to connect phase-to-ground loads to

FIGURE 2.13 ∆-Y transformer as a local source of ground current (grounding bank).
this system a grounding bank is connected to the system, as shown in Figure

2.13. Note that the ∆-connected winding is not connected to any external cir-
cuit in Figure 2.13. With a load current equal to 3 times i, each phase of the
grounded Y winding provides the same current i, with the ∆-connected second-
ary winding of the grounding bank providing the ampere-turns required to
cancel the ampere-turns of the primary winding. Note that the grounding bank
does not supply any real power to the load; it is there merely to provide a
ground path. All the power required by the load is supplied by two phases of
the ungrounded supply.
Example 2.2
A 13.8 kV ∆-connected power supply is connected to a 30-A single phase-
to-ground load with a grounding bank. How much KVA does the ∆-connected
power supply provide?
From the diagram in Figure 2.13, two of the power supply windings
carry one-third of the phase-to-ground current each, or 10 A each. Since the
phase-to-phase voltage is 13.8 kV, each of these windings supplies 13.8 kV #
10 A ! 138 KVA. The third winding carries no current. Thus, the power
supply provides 2 # 138 KVA ! 276 KVA.

The phase-to-ground voltage is 13.8 kV/1.732 ! 7.967 kV. Thus, the
KVA consumed by the 30 A load is 7.967 kV # 30 A ! 239 KVA. How do
we explain the apparent ‘‘excess’’ KVA from the power supply? Suppose the
load is connected between A phase and ground and let us assume the load
current is in phase with its phase-to-neutral voltage, both having a 0° angle.
Therefore, the power consumed by the load is 239 kW.
The load current is comprised of 10∠0° A from the A-B winding, 10∠0°
A from the A-C winding, and 10∠0° A from A phase of the grounding bank.
The A-to-B phase voltage is 13.8∠30° kV and the A-to-C phase voltage is
13.8∠$30° kV. The power outputs from the two windings are calculated
below.
S ab ! E ab # i*ab
S ac ! E ac # i*ac
where i*ab is the complex conjugate of the current i ab and i*ac is the complex
conjugate of the current i ac .
S ab ! 13,800∠30° ! 10∠0° ! 119.5 kW " 69 KVAR
S ab ! 13,800∠$30° ! 10∠0° ! 119.5 kW $ 69 KVAR
The total real power output is the same as the real power consumed, or
239 kW. The ‘‘excess’’ KVA output from the power supply is due to 69
KVAR of reactive power that circulates within the circuit.
2.8 THE ZIGZAG CONNECTION

The zigzag connection is also called the interconnected star connection. This
connection has some of the features of the Y and the ∆ connections, combining
the advantages of both. The zigzag connection is a three-phase connection
and is constructed as shown in Figure 2.14. There are three pairs of windings,
each having a 1:1 turns ratio. The left-hand set of windings shown in the
figure is a conventional Y connection, a′-b′-c′, with the neutral N brought out.
The open ends of the Y are electrically connected to the right-hand set of
windings as follows: a′ connects to the right-hand winding paired with to the
b′-N winding, b′ connects to the right-hand winding paired to c′-N winding,
and c′ connects to the right-hand winding paired to the a′-N winding. The
opposite ends of the right-hand windings are brought out as the phase terminals
a, b, and c.
The vector diagram shown on the right of Figure 2.14 makes it is obvious
why this is called a zigzag connection. It operates on the following principle:

FIGURE 2.14 Interconnected star or zigzag winding connection and vector diagram.
If three currents, equal in magnitude and phase, are applied to the three termi-
nals, the ampere-turns of the a′-N winding cancel the ampere-turns of the c′-
c winding, the ampere-turns of the b′-N winding cancel the ampere turns of
the a′-a winding, and the ampere-turns of the c′-N winding cancel the ampere
turns of the b′-b winding. Therefore, the transformer allows the three in-phase
currents to easily flow to neutral.
If three currents, equal in magnitude but 120° out of phase with each
other, are applied to the three terminals, the ampere-turns in the windings
cannot cancel and the transformer restricts the current flow to the negligible
level of magnetizing current. Therefore, the zigzag winding provides an easy
path for in-phase currents but does not allow the flow of currents that are 120°
out of phase with each other.
The ability to provide a path for in-phase currents enables us to use the
zigzag connection as a grounding bank, which is one of the main applications
for this connection. If a zigzag winding is used as a secondary winding with

FIGURE 2.15 ∆-zigzag transformer vector diagram.
a ∆ winding used as a primary winding, the ∆-zigzag connection is created,

as shown in Figure 2.15. A ∆-zigzag transformer is technically not a two-winding
transformer but rather a three-winding transformer because three separate
windings are wound around each core leg. Three winding transformers will
be discussed in greater detail in Chapter 4. Since two of the sets of windings
are interconnected, we treat the ∆-zigzag as if it were a two-winding trans-
former. As usual, the sets of windings that are magnetically linked on common
core legs are drawn in parallel to each other, as shown in Figure 2.15.
The ∆-zigzag connection provides the same advantages as the ∆-Y con-
nection, like third harmonic suppression and ground current isolation. One
added advantage is that there is no phase angle displacement between the
primary and the secondary circuits with this connection; therefore, the ∆-zig-
zag connection can be used in the same manner as Y-Y and ∆-∆ transformers
without introducing any phase shifts in the circuits.
2.9 COMPARISONS OF ECONOMY OF THE

DIFFERENT WINDING CONFIGURATIONS
Some of the advantages and disadvantages of the Y, ∆, and zigzag connections
have been discussed in terms of voltage distortion, ground current isolation,
etc., but their performance under load still needs to be addressed. A transform-
er’s load-carrying capability is determined primarily by the total I 2 R losses
in the windings, so an obvious way to reduce losses is to reduce the winding

currents. Since the KVA transformed is equal to the voltage across the winding
times the winding current, increasing the voltage greatly decreases I 2 R losses
for a given KVA transformed.
The resistance of the winding is proportional to its conductor length and
is inversely proportional to the conductor cross section area. Both resistance
and the losses are reduced if the total conductor length is reduced. For a given
set of core dimensions, however, the number of turns must be large enough
to limit the volts per turn to levels below saturation; therefore, the length of
the conductor must also be proportional to the voltage across the winding.
To compare the quantity of copper conductor required in transformers
using Y, ∆, and zigzag windings, assume that all three transformers operate
at the same phase-to-phase voltages, all three transform the same KVA, and
that all three core configurations are the same. The objective is to keep the
I 2 R losses constant by varying the amounts of materials used.
The phase-to-phase voltage across the ∆ winding is 1.732 times the
phase-to-ground voltage across the Y winding; therefore, the ∆ winding con-
ductor must be 1.732 times longer than an equivalent Y winding conductor
to limit the volts per turn. The load current through the ∆ winding is 0.577
times the load current through the Y winding for the same KVA. The losses
for each winding are calculated as follows.
LY
(I 2 R) Y ! (1.0 # i Y ) 2 # ρ # 1.0 # (2.9.1)
AY
LY
(I 2 R) ∆ ! (0.577 # i Y ) 2 # ρ # 1.732 # (2.9.2)
A∆
where
iY ! current in the Y winding
ρ ! resistivity of copper
LY ! conductor length of the Y winding
AY ! cross-sectional area of the Y winding conductor
A∆ ! cross-sectional area of the ∆ winding conductor
Since the I 2 R losses are to be the same for both windings, (I 2 R) Y !
(I R) ∆ and
2
1 0.577
! (2.9.3)
AY A∆
A ∆ ! 0.577 # A Y (2.9.4)

The total volume of the copper conductor is equal to its length times its cross-
section area:
VY ! LY # AY (2.9.5)
V ∆ ! 1.732 # L Y # 0.577 # A Y ! V Y (2.9.6)
Therefore, the quantity of copper used in a ∆ winding is about the same as

the quantity of copper used in an equivalent Y winding.
The zigzag winding is comprised of two windings in series. These series
windings are on different core legs and have different induced voltages. But
since the current through the two windings in series is equal to the phase-
to-neutral current, the current through the zigzag winding is the same as the
current through the Y winding. The voltage across each series winding in the
zigzag connection is 0.577 times the phase-to-neutral voltage; therefore,
the total length of conductor per phase in the zigzag winding is 2 # 0.577 !
1.155 times the conductor length of the equivalent Y winding. The losses for
each winding are calculated as follows.
LY
(I 2 R) Y ! (1.0 # i Y ) 2 # ρ # 1.0 # (2.9.7)
AY
LY
(I 2 R) ZZ ! (1.0 # i Y ) 2 # ρ # 1.155 # (2.9.8)
A ZZ
where
iY ! Y winding current
ρ ! resistivity of copper
LY ! conductor length of the Y winding
AY ! cross-sectional area of the Y winding conductor
A ZZ ! cross-sectional area of the zigzag winding conductor
Since the I 2 R losses are to be the same for both windings, (I 2 R) Y !

(I R) ZZ and
2
1 1.155
! (2.9.9)
AY A ZZ
A ZZ ! 1.155 # A Y (2.9.10)

The total volume of the copper conductor is equal to its length times
its cross-sectional area:
VY ! LY # AY (2.9.11)
V ZZ ! 1.155 # L Y # 1.155 # A Y ! 1.33 # V Y (2.9.12)
Therefore, the quantity of copper required in a zigzag winding is about 33%

greater than the quantity of copper used in an equivalent Y winding having
the same KVA rating. The added cost of copper in a zigzag winding and the
increased complexity of its design limit the use of zigzag windings to very
special applications where the unique advantages of the electrical characteris-
tics outweigh the disadvantages.
2.10 TRADE-OFF BETWEEN STEEL

AND COPPER IN THE DESIGN
OF A TRANSFORMER
The previous section illustrated the fact that reducing a winding conductor’s
length enables a corresponding reduction in the conductor’s cross-sectional
area to maintain the same total I 2 R losses. Therefore, to maintain constant
losses, the required volume of copper is proportional to the square of the con-
ductor length L.
V Cu % L 2 (2.10.1)
The required number of turns in a winding N is inversely proportional to the

volts per turn generated by the core. The volts per turn are proportional to the
total magnetic flux, and the flux is proportional to the cross-sectional area of
the core A Fe for a given allowable peak flux density, expressed as volts per
turn.
1
N% (2.10.2)
A Fe
From simple geometry, we know that the conductor’s length is equal to the
number of turns times the circumference of the coil. If the cross section of
the core is nearly circular and the winding is placed directly over the core,
the circumference of the coil is roughly proportional to the square root of the
core’s cross-sectional area.
L Cu % N # (A Fe) 1/2 % (A Fe) $1/2 (2.10.3)

1
V Cu % L 2 % (2.10.4)
A Fe
Assuming that the core’s volume is roughly proportional to the core’s cross-
sectional area,
1
V Cu % (2.10.5)
V Fe
The relationships given in Eq. (2.10.5) indicate that the volume of copper
required to limit I 2 R losses is inversely proportional to the volume of the core
for a given KVA rating, winding configuration, and applied voltage. In other
words, adding 25% more core steel should permit a 25% reduction in the
quantity of copper used in a transformer. This results in a 1:1 trade-off in
copper volume vs. core volume.
Remember from Eq. (1.8.7), however, that the total core losses are pro-
portional to the core volume for a given flux density. For example, if we decide
to reduce the volume of copper by 25% by increasing the volume of core steel
by 25%, the core losses will increase by 25% even though the conductor losses
remain constant. In order to maintain the same core losses, the flux density
must be reduced by increasing the cross-sectional area of the core, meaning
that additional iron must be added. Therefore, the 1: 1 trade off in copper
volume vs. core volume is only a very rough approximation. There are also
other practical physical limitations in selecting the dimensions of the core and
windings; however, this exercise does illustrate the kinds of trade-offs that a
transformer design engineer can use to optimize economy.
2.11 CONNECTING THREE-PHASE BANKS

USING SINGLE-PHASE TRANSFORMERS
There can be advantages to using single-phase transformers to make a three-
phase bank instead of building a three-phase unit. For instance, it may be
impossible or impractical to fabricate or ship a three-phase transformer with
an extremely large MVA capacity. A bank of three single-phase transformers
may then be the solution, although the total size, weight, and cost of three
single-phase units will probably exceed the size, weight, and cost of one three-
phase unit. An additional advantage of the bank arrangement is that a failure
of one single-phase unit will usually be less costly to repair than a failure of
a larger three-phase unit. Furthermore, one spare single-phase transformer is
usually all that is required to assure sufficient reliability for the entire bank.
With a three-phase transformer, an additional spare three-phase transformer
would be required, so the total cost of the installation plus a spare transformer

is twice the cost of the installation alone. The total cost of a bank of single-
phase transformers plus a spare is only 133% the cost of the bank alone. There-
fore, the total cost of a bank of single-phase transformers plus a spare is proba-
bly less than the cost of a three-phase transformer plus a spare.
Either Y or ∆ connections are possible with single-phase transformers
connected in banks. It is extremely important that the single-phase transform-
ers are carefully matched when they are banked together, especially when the
∆ connection is used. Using mismatched transformers in the ∆ connection will
result in excessive circulating currents that will severely de-rate the bank or
cause overheating. The operation of mismatched transformers will be explored
further in Chapter 3.
One interesting configuration for a three-phase bank is the open Y-∆
connection used extensively in rural distribution systems. The open Y-∆ con-
nection uses two single-phase transformers, as shown in Figure 2.16. An open
Y-∆ connection requires only two phases plus the neutral on the primary side
of the bank in order to develop a three-phase voltage at the secondary. This
is an obvious cost saving (in addition to the avoided cost of a third transformer)
when the installation is far away from a three-phase primary circuit. If one
of the transformers is center-tapped as shown in Figure 2.16, then the bank
provides a single-phase lighting leg in addition to a three-phase power circuit.
Example 2.3
An open Y-∆ bank comprised of two 10 KVA single-phase distribution trans-
formers supplies a balanced 240 V three-phase load. What is the maximum
KVA that can be supplied without exceeding the rating of the transformers?
FIGURE 2.16 Open Y-∆ transformer bank with two single-phase transformers sup-
plying a three-phase load.

Suppose we connect a 20 KVA load, which is equal to the total KVA
rating of the two transformers. The phase currents are calculated as follows:
1/3# 20,000 VA
i! ! 48.1 A
240 V # 0.577
All of the phase current flows through the winding since the open ends of the
∆ are connected to the load. The KVA transformed by each transformer is
equal to the secondary voltage times the phase current.
KVA transformed ! 240 V # 48.1 A ! 11.544 KVA
In order not to exceed the 10 KVA transformer rating, the load must be
reduced to 86.6% of 20 KVA. This demonstrates one disadvantage of the open
Y-∆ bank: The available KVA capacity is only 86.6% of the total KVA rating
of the two transformers. In practice, transformers used in open Y-∆ banks are
sized so that a third transformer can be added at a later date when the custom-
er’s load increases beyond the 86.6% limit to provide a full-capacity Y-∆ bank.
2.12 TRANSFORMING THREE-PHASE

VOLTAGES INTO TWO-PHASE
VOLTAGES
Occasionally, although rarely, one still may encounter a two-phase power sys-
tem that is supplied by a three-phase source. Two-phase systems can have
three-wire, four-wire, or five-wire circuits. Note that a two-phase system is
not merely two-thirds of a three-phase system. Balanced three-wire, two-phase
circuits have two phase wires, both carrying approximately the same amount
of current, with a neutral wire carrying 1.414 times the currents in the phase
wires. The phase-to-neutral voltages are 90° out of phase with each other.
Four-wire circuits are essentially just two ungrounded single-phase circuits
that are electrically 90° out of phase with each other. Five-wire circuits have
four phase wires plus a neutral; the four phase wires are 90° out of phase with
each other.
The easiest way to transform three-phase voltages into two-phase volt-
ages is with two conventional single-phase transformers. The first transformer
is connected phase-to-neutral on the primary (three-phase) side and the second
transformer is connected between the other two phases on the primary side.
The secondary windings of the two transformers are then connected to the
two-phase circuit. The phase-to-neutral primary voltage is 90° out of phase
with the phase-to-phase primary voltage, producing a two-phase voltage
across the secondary windings. This simple connection, called the T connec-

FIGURE 2.17 T transformer connection between a three-phase system and a two-
phase system.
tion, is shown in Figure 2.17. The main advantage of the T connection is

that it uses transformers with standard primary and secondary voltages. The
disadvantage of the T connection is that a balanced two-phase load still pro-
duces unbalanced three-phase currents; i.e., the phase currents in the three-
phase system do not have equal magnitudes, their phase angles are not 120°
apart, and there is a considerable amount of neutral current that must be re-
turned to the source.
2.13 THE SCOTT TRANSFORMER

CONNECTION
In order to overcome the disadvantage of the T connection, the Scott connec-
tion uses two single-phase transformers of a special design to transform three-

phase voltages and currents into two-phase voltages and currents. The first
transformer, called the ‘‘main,’’ has a center-tapped primary winding con-
nected to the three-phase circuit with the secondary winding connected to the
two-phase circuit. It is vital that the two halves of the center-tapped primary
winding are wound around the same core leg so that the ampere-turns of the
two halves cancel out each other. The ends of the center-tapped main primary
winding are connected to two of the phases of the three-phase circuit.
The second transformer, called the ‘‘teaser,’’ has one end of its primary
winding connected to the third phase of the three-phase circuit and the other
end connected to the center tap of the primary winding of the main. The Scott
connection requires no primary neutral connection, so zero-sequence currents
are blocked. The secondary windings of both the main and teaser transformers
are connected to the two-phase circuit. The Scott connection is shown in Fig-
ure 2.18 for a two-phase, five-wire circuit, where both secondary windings
are center-tapped and the center taps are connected to the neutral of the five-
wire circuit. Three-wire and four-wire configurations are also possible.
If the main transformer has a turns ratio of 1: 1, then the teaser trans-
former requires a turns ratio of 0.866: 1 for balanced operation. The principle
of operation of the Scott connection can be most easily seen by first applying
a current to the teaser secondary windings, and then applying a current to
the main secondary winding, calculating the primary currents separately and
superimposing the results.
Apply a 1.0 per unit load connected between phase 1 and phase 3 of
the secondary:
FIGURE 2.18 Scott transformer connection between a three-phase system and a two-
phase system.

Secondary current from the teaser winding into phase 1 ! 1.0∠90°
Secondary current from the teaser winding into phase 3 ! $1.0∠90°
Primary current from A phase into the teaser winding ! 1.1547∠90°
Primary current from B phase into the main winding ! 0.5774∠90°
Primary current from C phase into the main winding ! $0.5774∠90°
The reason that the primary current from A phase into the teaser winding is
1.1547 per unit is due to 0.866: 1 turns ratio of the teaser, transforming 1/
0.866 ! 1.1547 times the secondary current. This current must split in half
at the center tap of the main primary winding because both halves of the main
primary winding are wound on the same core and the total ampere-turns of
the main winding must equal zero.
Apply a 1.0 per unit load connected between phase 2 and phase 4 of
the secondary:
Secondary current from the main winding into phase 2 ! 1.0∠0°
Secondary current from the main winding into phase 4 ! $1.0∠0°
Primary current from B phase into the main winding ! 1.0∠0°
Primary current from C phase into the main winding ! $1.0∠0°
Primary current from A phase into the teaser winding ! 0
Superimpose the two sets of primary currents:
I a ! 1.1547∠90° " 0 ! 1.1547∠90°
I b ! 0.5774∠90° " 1.0∠0° ! 1.1547∠$30°
I c ! $0.5774∠90° $ 1.0∠0° ! 1.1547∠210°
Notice that the primary three-phase currents are balanced; i.e., the phase cur-
rents have the same magnitude and their phase angles are 120° apart. The
apparent power supplied by the main transformer is greater than the apparent
power supplied by the teaser transformer. This is easily verified by observing
that the primary currents in both transformers have the same magnitude; how-
ever, the primary voltage of the teaser transformer is only 86.6% as great as
the primary voltage of the main transformer. Therefore, the teaser transforms
only 86.6% of the apparent power transformed by the main.
We also observe that while the total real power delivered to the two-
phase load is equal to the total real power supplied from the three-phase sys-
tem, the total apparent power transformed by both transformers is greater than
the total apparent power delivered to the two-phase load. Using the numerical
example above, the total load is 2.0 per unit. The apparent power transformed

by the teaser is 0.866 # I a ! 1.0 per unit, and the apparent power transformed
by the main is 1.0 # I b ! 1.1547 per unit for a total of 2.1547 per unit of
apparent power transformed. The additional 0.1547 per unit of apparent power
is due to parasitic reactive power flowing between the two halves of the pri-
mary winding in the main transformer.
Single-phase transformers used in the Scott connection are specialty
items that are virtually impossible to buy ‘‘off the shelf’’ nowadays. In an
emergency, standard distribution transformers can be used, as illustrated in
the following example.
Example 2.4
(Note: The following example is taken from an actual case that occurred a
number of years ago.)
A small industrial electric customer has a plant with an antiquated two-
phase electrical system. The customer has a Scott-connected transformer bank
connecting this system to the local utility company which provides power.
This Scott-connected bank catastrophically failed and there are no replacement
transformers readily available. The utility company was called in to restore
service to the two-phase system, but the utility only has standard single-phase
and three-phase distribution transformers in its storerooms. The customer has
a five-wire, two-phase system with a phase-to-neutral voltage of 120 V. The
utility company’s distribution system has a phase-to-phase voltage of 12,470
V and a phase-to-neutral voltage of 7200 V. Customers are routinely supplied
with 120/240 V service using single-phase transformers connected either
phase-to-phase or phase-to-neutral on the primary side.
One solution would be to use the T connection with the standard trans-
formers that the utility had on hand, but this would result in unbalanced three-
phase currents. A bright young engineer working for the utility found a way
to construct a Scott-connected bank using standard transformers.
The teaser was replaced by a standard distribution transformer with a
12,470 V primary and a 120/240 V center-tapped secondary. The main trans-
former was replaced by two standard distribution transformers, each having
a 7200 V primary and a 120/240 V center-tapped secondary. The primary
windings of the replacement main transformers were connected in series and
their secondary windings were connected in parallel. These connections are
shown in Figure 2.19.
Since the two transformers substituted for the main transformer are not
wound on the same core leg, the secondary windings of the main transformers

FIGURE 2.19 Scott-connected transformer bank using three standard single-phase
distribution transformers, showing the current in the teaser primary current splitting
evenly between the two main primaries.
are interconnected to force the primary current in the primary winding of the
teaser to split evenly between the two primary windings of the main in the
same manner that a center-tapped winding forces the teaser current to split
evenly in the primary winding of the main in a Scott connection.
For a five-wire, two-phase circuit, the center tap of each of the three
secondary windings is connected to the common neutral. For a four-wire, two-
phase circuit, the center taps of the secondary windings are not brought out.
Note that the voltage across the 12,470 V primary winding of the teaser
is 86.6% of the voltage across the two 7200 V primary windings in series
of the main, just like a Scott-connected transformer. This produces balanced
operation; however, when the bank is connected to a 12,470 V three-phase
source, the phase-to-neutral output voltage is only 86.6% of 120 V, or 104 V.
Fortunately in this case, the three-phase distribution voltage at the customer’s
location was 5% higher than the nominal voltage and the transformers also
had taps to boost the output voltage by another 5%. The combination of the
5% higher system voltage and the 5% tap boost provided a two-phase second-

ary voltage of about 115 V. This was still below the 120 V nominal voltage
but it was within the operating voltage range of the customer’s two-phase
equipment.
2.14 THREE-PHASE TRANSFORMER

DESIGNS
In the preceding sections we saw some of the ways that single-phase trans-
formers can be connected in three-phase and two-phase systems. It is some-
times advantageous to construct a single three-phase transformer instead of
using a bank of single-phase transformers. For instance, a three-phase trans-
former can often be more economical to build by enclosing one core and coil
structure inside one transformer tank instead of building three separate core
and coil structures and tanks.
The first basic design for three-phase transformers to be discussed is the
core form design. This design includes the three-legged core form design and
the five-legged core form design. In the three-legged core form design, three
sets of windings are placed over three vertical core legs. Each core leg and
its set of windings is corresponds to one phase. Each core leg is joined to a
top yoke and a bottom yoke, which complete the magnetic circuit. The general
layout of the three-legged core form design is shown in Figure 2.20. The set
FIGURE 2.20 Three-legged core form transformer.

of windings on the center phase are cut away to show the placement of the
LV and HV windings around the center core leg.
The construction of the core follows the same principles as described
in Chapter 1. The core is made of thin steel laminations that are stacked to-
gether. The cross section area of the yokes must be sufficient to carry the full
flux of each phase. There are various methods of making joints between the
core legs and the yokes; the method favored at the present is the mitered joint
used with the modern grain-oriented steels. The core and coil cross sections
are usually circular, although a square design is sometimes used. Any of the
winding connections described earlier, such as Y, ∆, and zigzag, can be imple-
mented in the three-legged core form design.
The one feature that makes the three-legged core form design unique is
the fact that there is apparently no return path for the magnetic flux converging
in the top and bottom yokes from the three core legs. This would imply that
the 3 fluxes arriving at the top core yoke would have to jump across a huge
air gap to return to the bottom core yoke. Further examination reveals the
secret: The flux through each core leg is sinusoidal since the voltages applied
across the windings are sinusoidal. As long as fluxes have the same magnitude
and their phase angles are electrically 120° apart, the fluxes will cancel out
each other in the top and bottom yokes. Therefore, for three-phase balanced
applied voltages, no flux return path is required.
If the applied voltages are not balanced, however, then there will be
residual flux that must be dealt with. Since the unbalanced flux travels along
a high-reluctance path through a very long air gap and since the inductance of
a coil is inversely proportional to the reluctance of its flux path, the unbalanced
voltage component encounters only a small inductance. Therefore, the low
inductance presented by the return path of a three-legged core transformer
tends to ‘‘short out’’ any voltage unbalance. This effectively links the three
phases together through a mutual magnetic path and tends to reduce voltage
unbalance between phases. We shall see in a later chapter that this has the
same effect as a ∆-connected tertiary winding.
This has a major advantage in the case of the Y-Y connection. We saw
earlier that if the neutrals are not connected to an external circuit, then third
harmonic voltages would be impressed across the windings because third har-
monic magnetizing currents cannot flow. In a three-legged core design, the
third harmonic flux from the three core legs add in phase at the top and bottom
yokes and encounter a high-reluctance path. Restricting the third harmonic
flux greatly reduces the third harmonic voltages that would otherwise exist in
Y-Y transformers. For this reason, along with the economic savings of not

having to provide a magnetic return path between the top and bottom yokes,
three-legged core form designs are used extensively with Y-Y transformers.
In large power transformers, third harmonic flux and stray 60 Hz flux
from unbalanced voltages may leave the iron core and enter free space inside
the transformer. This induces currents in the internal metal parts of the trans-
former and may cause severe localized overheating. The five-legged core form
design solves this problem by providing flux paths around the three core legs
between the top and bottom yokes. The layout of the five-legged core form
transformer is shown in Figure 2.21. Residual flux, labeled φ, is the total flux
arriving at the top core yoke from the core legs of the three phases. A fourth
and fifth core leg provide two return paths for the residual flux from the top
to the bottom yoke.
The top and bottom core yokes are often made with a reduced cross-
sectional area because they do not have to carry the full complement of flux
from each phase. This has the advantage of reducing the overall height of the
transformer. The disadvantage of reducing the cross-sectional area of the
yokes is that a portion of the normal flux from the outer phases must now
flow through the fourth and fifth core legs. This makes the actual flux path
uncertain and makes calculating core losses difficult.
The five-legged core form design has electrical characteristics that are
very similar to a bank of three single-phase transformers; i.e., the three phases
operate more or less independently with a relatively small magnetic interaction
between the phases.
FIGURE 2.21 Five-legged core form transformer.

The shell form design is a completely different design from the three-
phase core form design. In a shell form transformer, the windings are con-
structed from flat coiled spirals that are stacked together like pancakes. For
this reason, the windings in a shell form design are often referred to as pancake
windings. In a two-winding shell form transformer, the low-voltage winding
is usually split into two windings with the high-voltage winding sandwiched
between the two halves of the low-voltage winding. Instead of a circular shape,
the pancake coils are actually square shaped with the outer corners rounded
off.
The centers of the pancake coils are hollow and square-shaped. Core
legs with square cross sections pass through the centers of the pancake coils.
The core legs are laid horizontally so the coils are stacked horizontally on
edge. The return paths for the core go around the coils forming a ‘‘shell’’
around the windings; hence the name shell form. The basic shell form design
is shown schematically in Figure 2.22.
The core without windings is shown on the left hand part of Figure 2.22.
The core is divided into two halves with each half carrying approximately
50% of the total flux. The three sets of windings are placed around the longitu-
dinal sections of the core as shown in the middle part of the figure as viewed
FIGURE 2.22 Three-phase shell form transformer.

from above the transformer. The top part of the figure shows the end cut away,
clearly illustrating that the pancake coils are square-shaped with rounded cor-
ners. The edges of the core laminations are also seen in this view. The right
part of the figure is an exploded end view of the pancake windings divided
into three sections: The low-voltage winding is split into two halves, which
sandwich the high-voltage winding in the middle.
The electrical characteristics of the shell form transformer are similar
to a five-legged core form transformer or a bank of three single-phase trans-
formers; i.e., there is not a strong magnetic interaction among the different
phases at normal levels of excitation. All the various three-phase winding
connections are available in three-phase shell form transformers, such as the
Y, ∆, and zigzag. The major advantages of the shell form design are that it
is more compact than core form transformers and it has great mechanical
strength. The main disadvantages of the shell form design are that it is much
more difficult to assemble than the core form design, and there are tighter
electrical clearances to contend with.
The shell form transformer technology was developed by Westinghouse
Electric Corporation and was licensed to a number of transformer manufactur-
ers. Both single-phase and three-phase shell form transformers are made.
There are very few manufacturers that still make shell form transformers to-
day, despite the fact that this design has definite advantages in certain applica-
tions.
Example 2.5
In a shell form transformer, the cross-sectional areas of each of the core sec-
tions are only sufficient to carry a peak flux density equal to the flux produced
by one set of phase windings. Sketch a diagram of a three-phase shell form
transformer core showing the directions that the flux paths must take in order
that the total flux in any section does not exceed the magnitude of flux gener-
ated by one phase. There are three components of flux that are electrically
120° apart. Label these flux components 1, 2, and 3. Sketch the flux throughout
the core, indicating the directions of the flux in each core section.
The solution appears in Figure 2.23. Assuming that the flux generated
by each phase is sinusoidal and the three phases are electrically 120° apart,
the flux components cancel at each point marked by the letter X. The flux
components flowing in the lateral sections of the core are not generated di-
rectly by the windings but are the fluxes of two phases combining at the points
marked X.
Note that the direction of flux in the longitudinal core leg in the middle

FIGURE 2.23 Flux paths in a three-phase shell form transformer.
phase must be in a direction that is opposite from the direction of the flux in
the core legs of the other phases in order to cancel out the flux arriving at
each of the points marked X. If the directions of the flux in all the three core
legs are in the same direction, then the magnitude of the total flux arriving at
each of the points marked X will be 1.73 times the magnitude of the flux
produced by one phase. This will drive the lateral core sections into saturation.
The desired configuration of the core flux shown in Figure 2.23 is pro-
vided simply by connecting the center-phase windings with polarity opposite
of the other two phase windings.

2.15 STANDARD TERMINAL MARKINGS
FOR TRANSFORMERS
The electrical connections to transformer windings are brought out of the
transformer enclosure by leads that pass through insulated bushings, which
will be covered in more detail in Chapter 6. The bushings can be located on
the top or on the sides of the transformer and are marked in a standard way
that is consistent throughout the industry [2].
For single-phase two-winding transformers, the high-voltage bushings
are labeled H1 and H2 and the low-voltage bushings are labeled X1 and X2.
The labels indicate the polarity of the terminals; i.e., if the voltage at the H1
bushing is instantaneously positive with respect to H2, then the voltage at the
X1 bushing is instantaneously positive with respect to X2. If the windings of
a single-phase transformer are connected line-to-neutral, then the H1 and X1
bushings are usually connected to the line with the H2 and X2 bushings are
connected to the neutral.
The physical placement of the bushings on the transformer is also stan-
dardized. If the bushings are mounted on the top of the transformer, the H1
bushing is always located in the upper-left quadrant of the transformer lid as
seen from above the transformer, and the H2 bushing is located in the upper-
right quadrant. The locations of the X1 and X2 bushings can either be lower
left and lower right, respectively, or lower right and lower left, respectively.
In the former case the transformer is said to have a subtractive polarity, and
in the latter case the transformer is said to have an additive polarity.
The way to remember the convention for additive and subtractive polar-
ity is to draw a voltage vector arrow from the H2 bushing to the H1 bushing
and draw a voltage vector arrow from the X2 bushing to the X1 bushing,
indicating an instantaneous positive polarity at the H1 and X1 terminals. If
the voltage vector arrows point in the same direction in a circular path around
the perimeter of the transformer, the transformer is additive. If the vector
arrows point in opposite directions in a circular path around the perimeter of
the transformer, the transformer is subtractive. Schematic diagrams of additive
and subtractive polarity transformers are shown in Figure 2.24.
The polarity of an unmarked single-phase transformer can be determined
by a simple test: Apply 120 VAC across the high-voltage bushings (not across
the low-voltage bushings, please!). Connect a jumper wire from one of the
high-voltage bushings to the nearest low-voltage bushing on the opposite side
of the transformer. Measure the voltage between the other high-voltage bush-
ing and the other low-voltage bushing. If the measured voltage is less than
120 V, then the transformer is subtractive. If the measured voltage is greater

FIGURE 2.24 Placement of the bushings for additive-polarity and subtractive-
polarity single-phase transformers.
than 120 V, then the transformer is additive. A method of verifying trans-

former polarity that is more safe uses a transformer turns ratio (TTR) test set,
which will be discussed in Chapter 8.
Single-phase transformers with ratings 200 KVA and below and having
high-voltage ratings of 8660 V and below are generally additive polarity,
whereas single-phase transformers above 200 KVA or with high-voltage rat-
ings above 8660V are generally subtractive polarity [3].
Although this is the standard convention, it may be possible for two
transformers with the same KVA and voltage rating to have opposite polari-
ties. Note that nothing prevents connecting subtractive and additive transform-
ers together in a three-phase bank as long as the correct polarities of the leads
are observed. There are no electrical differences between a subtractive and an
additive transformer; only the physical locations of the low-voltage bushings
are different.
If a low-voltage winding is center tapped, which is common in single-

phase distribution transformers, then the low-voltage bushings are labeled X1,
X2, and X3. The X1 and X3 bushings are connected across the full winding
and the X2 bushing is connected to the center tap. The instantaneous polarity
of voltage at the X1 bushing is the same as the polarity of the voltage at the
H1 bushing.
Polarity dots are sometimes used instead of labeling the transformer
leads H1 and X1 labels, particularly with instrument transformers. A polarity
dot on a high-voltage lead is equivalent to marking the lead H1, and a polarity
dot on a low-voltage lead is equivalent to marking the lead X1. In other words,
polarity dots indicate the leads that have the same instantaneous voltage po-
larity.
Current transformers are instrument-type transformers that are used to
transform currents instead of transforming voltages. For a current transformer,
current flowing into a terminal, lead, or window that is marked with a polarity
dot produces an output current flowing out of the terminal or lead that is
marked with a polarity dot on the other winding.
The standard terminal markings for three-phase transformers are only
slightly more complicated than markings for single-phase transformers. For
three-phase, two-winding transformers, the phase leads of the high-voltage
FIGURE 2.25 Problem of Example 2.6.

windings are connected to high-voltage bushings labeled H1, H2, and H3. If
the high-voltage winding has an external neutral, this is brought out to a neutral
bushing marked H0. The phase leads of the low-voltage windings are con-
nected to low-voltage bushings labeled X1, X2, and X3. If the low-voltage
winding has an external neutral, this is brought out to a neutral bushing marked
X0. There is no H0 or X0 bushing for a ∆ winding or a Y winding without
an external neutral connection.
If the high-voltage bushings are connected to a three-phase system with
a phase rotation H1-H2-H3, the phase rotation of the low-voltage bushings is
X1-X2-X3. In standard Y-Y and ∆-∆ connected transformers, the voltage at
the X1 bushing is in phase with the voltage at the H1 bushing. In standard
Y-∆ and ∆-Y transformers connected to a system with a 1-2-3 phase rotation,
the X1 voltages lags the H1 voltage by 30°.
Nonstandard phase displacements can also be specified for transformers
used in special applications. For example, Y-Y transformers can be specified
with 180° phase displacement between the H1 and X1 terminals instead of a
0° phase displacement, and ∆-Y transformers can have the low-voltage phases
leading the high-voltage phases by 30° for a 1-2-3 phase rotation instead of
lagging the high-voltage phases by 30°.
FIGURE 2.26 Solution of Example 2.6.

FIGURE 2.27 Three-phase core form transformer in assembly at the factory.
FIGURE 2.28 Three-phase shell form transformer in assembly at the factory.

The placement of the bushings in a three-phase transformer is also stan-
dardized. When bushings are mounted on the top of the transformer lid, the
high-voltage bushings are arranged H0, H1, H2, and H3 from left to right in
the upper half of the lid, as seen from above the transformer. The low-voltage
bushings are arranged X0, X1, X2, and X3 from left to right in the lower half
of the lid, as seen from above the transformer. If side-mounted low-voltage
bushings are used, they are arranged X0, X1, X2, and X3 from left to right
facing the transformer from the low-voltage side. If side-mounted high-voltage
bushings are used, they are arranged H3, H2, H1 and H0 from left to right
facing the transformer from the high-voltage side. The terms ‘‘additive polar-
ity’’ and ‘‘subtractive polarity’’ do not apply to three-phase transformers.
Example 2.6
Assume that the single-phase transformers shown in Figure 2.25 have standard
terminal markings. Label the terminals and show the proper connections for
a ∆-Grd.Y connection (with the low-voltage circuit Y-connected) with the
high voltage lagging the low voltage by 30°.
The proper connections are shown in Figure 2.26. The H1 bushings are
always on the upper left of the lid, per the standard arrangement. The low-
voltage bushings are labeled according to whether the transformer is additive
or subtractive. When the low-voltage windings are connected phase-to-neutral,
the X1 bushings are normally connected to the phase wires and the X2 bush-
ings are connected to the neutral. With the connection shown in the figure,
the voltages at the high-voltage bushings lag the voltages at the low-voltage
bushings by 30°.
Figure 2.27 shows the core and coil assembly of a three-phase core form
tansformer seen from the high-voltage side of the transformer. Figure 2.28
shows the core and coil assembly of a three-phase shell form transformer.
REFERENCES
1. R. L. Bean, N. Chakan, Jr., H. R. Moore, and E. C. Wentz. Transformers for the
2. ANSI Std. C57.12.70–1978. American National Standard Terminal Markings and
Connections for Distribution and Power Transformers. American National Stan-
dards Institute, New York, 1978, pp. 18–19.
3. IEEE Std. C57.12. 00–2000. IEEE Standard General Requirements for Liquid-
Immersed Distribution, Power, and Regulating Transformers. Institute of Electrical
and Electronics Engineers, Inc., New York, 2000, pp. 11–12.

3
Transformer Impedance
and Losses
Until now, we have considered only ideal, lossless transformers obeying the
fundamental transformer laws: Voltages and currents are transformed strictly
according to the transformer turns ratio, and the power output from the trans-
former is equal to the power input to the transformer. The conditions expressed
by the ideal transformer laws are approached, but never realized in physical
transformers. Transformed voltages and currents are always less than the val-
ues predicted by the turns ratio because of losses. This chapter explains the
origins of transformer losses and develops the concept of equivalent circuits
of real transformers.
3.1 LEAKAGE FLUX AND LEAKAGE

REACTANCE
In an ideal two-winding transformer excited by the primary winding, all of
the magnetizing flux is within the core and both the primary and secondary
windings are linked by the same flux. Figure 3.1 depicts the ideal transformer
in a cutaway diagram of one phase of a two-winding core form transformer
with load currents in the primary and secondary windings, assuming a load

FIGURE 3.1 Flux in an ideal transformer under load. All of the magnetizing flux is
contained in the iron core with the ampere-turns of the primary canceling the ampere-
turns of the secondary.
is connected to the secondary winding and a voltage is applied across the

primary winding.
In Figure 3.1, the currents flowing out of the page are denoted by the
symbol ‘‘•’’ and currents flowing into the page are denoted by the symbol
‘‘!.’’ Note that it is not necessary for the actual number of turns or the trans-
former turns ratio to be shown. Since the total ampere-turns in the primary
are approximately equal to the total ampere-turns in the secondary, the wind-
ings are simply drawn with the same number of turns with the same current
in each turn.
The magnetic flux is denoted by the dotted lines inside the core in Figure
3.1. For this particular transformer, it takes four lines of flux in the core in
the upward direction to induce a voltage equal to the voltage applied across
the primary winding. The spaces between the two windings and between the
windings and the core are shown greatly exaggerated. The magnetizing current
is assumed to be negligible compared to the load currents.
The situation in a real transformer is somewhat different than described
above. The main difference is that all of the magnetic flux is not contained
in the core. This is because the load currents in the primary and secondary

Transformer Impedance and Losses 71
windings are considerably greater than magnetizing current, so we cannot ig-

nore the magnetic fields induced by these currents in the spaces surrounding
the winding conductors. Figure 3.2 shows these magnetic fields as the dotted
lines circulating around the windings in the spaces between the conductors.
The local magnetic flux circulating around the primary winding are ap-
proximately equal to the local magnetic flux circulating around the secondary
winding because the primary ampere turns are approximately equal to the
secondary ampere turns. Also, the magnetic flux is in phase with the currents
that produce it. For the time being, suppose the load connected to the trans-
former secondary is purely inductive. The phase angles of both the load current
and the circulating flux will lag the secondary voltage by 90°. Because induced
voltages are proportional to the rate of change of flux, any flux pointing in
the upward direction that is enclosed by the primary or secondary windings
will induce voltages in phase with the applied voltage. Conversely, any flux
pointing in the downward direction that is enclosed by the primary or second-
ary windings will induce voltages in these windings 180° out of phase with
the applied voltage.
If the number of lines of flux in the core would remain constant at four
lines pointing upward, the net number of flux lines contained pointing in the
FIGURE 3.2 Flux in a real transformer under load. Flux generated by the conductor
currents surround the windings, excluding flux from the core and reducing the second-
ary voltage.

upward direction enclosed by the primary winding would increase by two
lines. This would naturally increase the voltage induced across the primary.
In order for the voltage induced across the primary to remain equal the applied
voltage across the primary, the net number of flux lines pointing in the upward
direction must remain the same. This can be accomplished only if the number
of lines within the core decreases to two lines pointing upward. Consequently,
two lines of flux have been excluded from the core because of the flux circulat-
ing in the spaces around the windings.
The opposite situation exists for the secondary winding. If the number
of lines of flux in the core would have remained constant at four lines pointing
upward, the net number of flux lines pointing in the upward direction enclosed
by the secondary winding would have decreased by two lines. But as shown
in the preceding paragraph, the number of lines in the core must also decrease
by two lines to balance the voltage across the primary winding. Therefore,
the net number of flux lines in the vertical direction enclosed by the secondary
winding will decrease by four lines, which means there are no lines enclosed
by the secondary winding and the induced voltage across the secondary wind-
ing will be reduced to zero.
The above situation can actually exist when the secondary winding is
short-circuited, so short-circuiting the secondary winding results in a purely
inductive winding current with some of the flux excluded from the core. Note,
however, that some residual flux remains in the core and that the short-circuit
currents are still finite. This suggests that some sort of inherent restriction or
impedance limits the short-circuit currents in the transformer.
The composite of all flux in the spaces around and between the conduc-
tors is called leakage flux, because this can be visualized as flux ‘‘leaking’’
out of the core through empty space. Because the permeability of iron is finite,
there will always be some flux that leaks from the core, even without any load
current. However, the leakage flux increases considerably as the currents in
the windings increase. Since the leakage flux travels through empty space
instead of through iron, there is no hysteresis or saturation and the permeability
in this region is a constant equal to µ 0 . Recalling that the ratio B/H is equal
to the permeability and that H is directly proportional to the load current, the
leakage flux is in phase with, and is directly proportional to, the load current:
φ leakage " B leakage # µ 0 ! H leakage " I load (3.1.1)
The voltage induced across the secondary winding is equal to minus the
rate of change of the flux in the core:
dφ
E s # $ core (3.1.2)
dt

Let
E s # secondary voltage assuming no leakage flux
E s′ # secondary voltage with leakage flux
∆E s # E s $ E s′ (3.1.3)
As the magnitude of the leakage flux increases, the magnitude of flux
in the core decreases. The drop in secondary voltage is therefore directly pro-
portional to the rate of change of the load current:
dφ leakage
∆E s # " dI load (3.1.4)
dt
For a purely inductive load, ∆E s is in phase with E s′. For a purely resistive
load, ∆E s leads E s′ by 90°. The vector relationships are shown in Figure 3.3.
The relationship between load current and secondary voltage is equiva-
lent to placing a physical impedance in series with the output of an ideal
FIGURE 3.3 Vector relationships between the no-load secondary voltage, the sec-
ondary voltage with load, and load current.

transformer. This equivalent impedance is called the leakage reactance of the
transformer because it is an external manifestation of the effect of leakage
flux on secondary voltage. Leakage reactance limits short-circuit currents, and
is therefore useful, but it also reduces the secondary voltage under load (regu-
lation) and consumes reactive power. Varying the winding dimensions and
the spacing between the windings can control the amount of leakage reactance.
For example, if the spaces between the windings are kept small, there will be
fewer flux lines contained in these spaces and the leakage reactance will
be small. Placing the windings as close together as possible increases the
‘‘coupling’’ between them, which is the same thing as reducing the leakage
reactance.
3.2 CONDUCTOR LOSSES

Chapter 2 briefly discussed I 2 R conductor losses in transformer windings. It
was determined that the resistance of the winding is proportional to the con-
ductor length divided by the conductor cross-sectional area. While this is true
for DC currents, it is actually an oversimplification for AC currents where
additional conductor losses must be taken into account. These additional losses
affect the transformer design to some extent.
When an alternating magnetic field is applied to any conductor, eddy
currents are induced around the paths surrounding the lines of magnetic flux
that penetrate the conductor. These currents generate local I 2 R losses even if
the conductor itself is not carrying any net electrical current.
Large amounts of leakage flux can occur when a transformer is heavily
loaded. The magnetic fields associated with leakage flux not only penetrate
the winding conductors themselves, but can involve other metallic parts as
well. The eddy currents that are induced by these fields are proportional to
the leakage flux, which in turn is proportional to the load currents. Therefore,
the square of eddy currents and the eddy-current losses are both proportional
to the square of the load current. These eddy losses are externally manifested
by a component that increases the effective resistance of the conductors, even
if the eddy losses occur in metallic parts that are electrically isolated from the
conductors. Let this eddy-loss component of the conductor resistance be de-
noted R e.
When an AC current flows in a conductor, the magnetic fields within
the conductor form a series of concentric circles. The flux density B at any
point in the conductor is proportional to the total current enclosed by the mag-
netic path divided by the length of the circular path. Moving away from the
center of the conductor, the total current enclosed by the path tends to increase

faster than the length of the path. Therefore, the flux density increases near
the outer edges of the conductor. The direction of the magnetic field is perpen-
dicular to the direction of the current flow, and this forces current toward the
edge of the conductor and reduces the flux density near the center at the same
time. The concentration of current toward the edge of a conductor is called
the skin effect, reducing the area of the conductor that actually carries current
and increasing the effective resistance of the conductor. The skin effect is more
pronounced for large-diameter conductors. Let the skin-effect component of
the conductor resistance be denoted R s .
The total AC resistance of the conductor, including the eddy-loss com-
ponent and the skin-effect component is expressed by the following equation:
R AC # R DC % R e % R s (3.2.1)
where R AC is the AC resistance of the conductor and R DC is its DC resistance.
The conductor losses are equivalent to placing a lumped resistance in
series with the terminals of an ideal transformer. Conductor losses are com-
monly referred to as load losses, because they result only from load currents.
Load losses are sometimes referred to as copper losses; however, this is some-
what of a misnomer. As we have just seen, eddy-current losses in any metallic
part that is exposed to leakage flux will still show up as load losses.
Load losses limit the KVA capacity of a transformer because the heat
generated by these losses increase temperatures. Therefore, it is highly desir-
able to reduce the load losses as much as possible by reducing the AC resis-
tance of the conductor. Reducing R DC as well as R e and R s can do this. Reduc-
ing R DC can be done by shortening the conductor length and/or by increasing
the conductor cross-sectional area. Shortening the conductor length can only
be achieved to a point, and increasing the conductor cross-sectional area has
the unfortunate effect of increasing both the eddy-current losses and the skin-
effect losses. These losses can be reduced by special conductor designs.
Subdividing the conductors into strands that are insulated from each
other to break up the eddy current paths can reduce eddy-current and skin-
effect losses. Generally, the strands have a rectangular shape with the long
dimension oriented in the same direction as the leakage flux. By subdividing
one large-area conductor into a number of small-area conductors, the skin
effect is substantially reduced as well.
If a number of strands were simply bundled together, the strands would
be exposed to varying amounts of leakage flux and different induced voltages.
This would force more current to flow in some strands and less in others,
increasing the total losses. If the strands are properly transposed, each strand
is exposed to the same amount of leakage flux with equal voltages induced

FIGURE 3.4 Seven-conductor transposed cable used in a transformer winding mak-
ing a single transposition. After seven such transpositions, the conductors return to the
original configuration.
in each of the strands. Transposition allows the current to divide equally

among the strands to optimize the use of the entire cross section area of the
conductor. The transposition of a seven-strand cable is illustrated in Figure
3.4, showing the top, front, end, back and bottom views in sequence. After
seven complete transpositions, all the strands return to their original positions.
3.3 NO-LOAD LOSSES

Core losses were briefly discussed in Chapter 1. Alternating magnetic flux
produces both hysteresis losses and eddy-current losses in the steel. As we
have seen, hysteresis losses depend on several factors including the frequency,
the peak flux density, the type of core steel used, and the orientation of the
flux with respect to the ‘‘grain’’ of the steel. All of the above factors, except
the frequency, are under the control of the transformer designer. Core losses
are sometimes referred to as iron losses and are commonly referred to as no-
load losses, because core losses do not require load currents.
Decreasing the induced voltage per turn can reduce the peak flux density.

This obviously involves increasing the numbers of turns in both the primary
and secondary windings in order to maintain the same transformer turns ratio.
As we saw earlier, the disadvantage of adding more turns is that this increases
the length of conductor and increases the conductor resistance. More cross-
sectional area is required in order to keep the resistance constant. Doubling
the number of turns requires about four times the volume of copper.
Another way of reducing core losses is to use various types of low-loss
core steels that are now available, including ‘‘amorphous’’ core materials,
which have extremely low losses and superior magnetic properties. Unfortu-
nately, amorphous core materials have ceramic-like properties, so fabricating
transformer cores with these materials is much more difficult than with lami-
nated steel cores.
With grain-oriented steel, the direction of the core flux must be kept
more or less parallel to the grain of the steel by mitering the corners of the
laminations where the flux changes direction by 90°. Since the flux will cross
the grain at about a 45° angle at the mitered edges, the hysteresis losses will
increase somewhat in these places. These additional localized core losses must
be factored into the calculation of the total core losses.
Building up the core with thin laminated strips controls eddy losses in
the core, each strip having an oxide film applied to the surface. The oxide film
is extremely thin and it is more like a high-resistance film than true electrical
insulation; but since the potential differences between adjacent laminations is
quite small, the resistance of the oxide film is very effective in breaking up
the eddy current paths.
During the manufacture of the core, the core cutting machine must not
be allowed to get dull; otherwise, ‘‘burrs’’ will form along the edges of the
laminations. Burrs are imperfections that form electrical bridges between the
laminations and create paths for eddy currents and increased losses. Some-
times the eddy currents near a burr can be large enough to cause localized
overheating that can actually cause core damage.
Core losses are approximately proportional to the square of the excita-
tion voltage E applied to the transformer. Therefore, placing an equivalent
linear conductance G m across the transformer terminals can approximate trans-
former core losses. The core losses are expressed by
Wm # E 2 Gm (3.3.1)
Example 3.1
A certain large transformer core has a square cross section 24 in. on each side
and is assumed to have a uniform flux density. At the normal operating voltage,

the flux produces 90 V per turn (RMS). Each core lamination has an oxide
film on one surface that is 1 ! 10 $4 in. thick and the total thickness of each
lamination is 0.012 in. Determine the voltage difference between adjacent lam-
inations along the perimeter of the core. Calculate the resistivity ρ of the oxide
film required to limit the maximum circulating current losses to less than 1
mW/in. of surface along the perimeter of the core.
There are 2000 laminations in the core:
24 in.
n# # 2000
0.012 in.
Since steel is a good electrical conductor, the voltage through the steel itself
can be assumed to be nearly zero, so that nearly all of the voltage induced
around the perimeter is developed across the layers of oxide film between the
laminations. The voltage across each side of the lamination stack is 50% of
the volts per turn induced around the perimeter of the core. Therefore, the
voltage difference between each pair of laminations is calculated below. Refer
to Figure 3.5.
Volts per lamination # 50% ! 90 V per turn/2000 laminations
# 0.0225 V/lamination
We want to limit the losses W to 1 mW/in.2:
E 2 (0.0225 V) 2
W# # & 1 ! 10 $3 W/in.2
R R
FIGURE 3.5 Core with 24 in.2 cross section used in Example 3.1.

Solving for R,
(0.0225 V) 2
R' # 0.506 Ω-in.2
10 $3 W/in.2
R # ρ ! oxide thickness # ρ ! 10 $4 in.
ρ ' 0.506 Ω-in.2 /10 $4 in. # 5060 Ω-in.
For comparison, the resistivity of graphite is around 3500 Ω-in.; therefore, an

oxide film with the minimum resistivity allowed would actually be a fairly
good electrical conductor. It is a good idea to design the core with some electri-
cal conductivity between the laminations to prevent static charges from build-
ing up between the laminations. Static charges in the core are allowed to bleed
off to ground through an electrical connection at a single point, called the core
ground.
3.4 MAGNETIZING REACTANCE

For an ideal transformer, the magnetizing current is assumed to be negligible.
For a real transformer, some magnetizing current must flow when voltage is
applied to the winding in order to establish a flux in the core. The voltage
induced in the winding by the flux restrains the magnetizing current.
It was shown earlier that the magnetizing current is not really sinusoidal,
but contains many odd harmonics in addition to the fundamental frequency.
If we neglect the harmonics and concentrate on the fundamental frequency,
the magnetizing current in the winding lags the applied voltage by 90°. In a
two-winding transformer, this is equivalent to placing a reactance X m, called
the magnetizing reactance, in parallel with the transformer terminals.
The peak value of the magnetizing current is determined from the B-H
curve of the core, which we have seen is very nonlinear. Therefore, the mag-
netizing reactance is not a constant but is voltage dependent; however, if the
peak flux density is kept well below the point of saturation, X m can be approxi-
mated by a constant reactance in most engineering calculations.
It is generally desirable to maximize X m in order to minimize the mag-
netizing current. We saw earlier that inductance is inversely proportional to
the reluctance of the core along the flux path and the reluctance of an air gap
is several thousand times the reluctance of the same distance through the steel.
Therefore, even tiny air gaps in the flux path can drastically increase the core’s
reluctance and decrease X m . A proper core design must therefore eliminate all
air gaps in the flux path. In Chapter 1 we saw how alternate layers of core

steel are stacked so that flux is diverted around the gaps where laminations
butt together. Since any flux that is diverted must flow between the laminations
through their surfaces, it is vital that these surfaces lie perfectly flat against
each other. All ripples or waves must be eliminated by compressing the core
laminations together tightly. This also points out why the oxide layers on the
lamination surfaces must be extremely thin: since these layers have essentially
the same permeability as air and since the flux that is diverted from the air
gaps must then travel through these oxide layers, the core’s reluctance would
greatly increase if these layers were not kept extremely thin.
3.5 EQUIVALENT CIRCUIT OF A

TWO-WINDING TRANSFORMER
So far, the following elements of the equivalent circuit have been discussed
in some detail: the leakage reactance, the load losses, the core losses and the
magnetizing reactance. The leakage reactance is expressed as an inductive
reactance in series with the secondary winding, but it is more correctly shown
as split between the primary winding X p and the secondary winding X s . Simi-
larly, the load losses are expressed as resistance R p , in series with the primary
winding, and resistance R s , in series with the secondary winding. An ideal
transformer is connected behind the series impedances. The magnetizing re-
actance X m is approximated by a constant value, and the core losses are repre-
sented by a conductance G m . These last two elements are shunted in parallel
with the ideal transformer. The complete equivalent circuit of the transformer
is shown in Figure 3.6.
This equivalent circuit can model all of the electrical properties of a
two-winding transformer. This equivalent circuit also applies to all three-phase
FIGURE 3.6 Equivalent circuit of a two-winding transformer in positive phase se-

quence and negative phase sequence networks.

FIGURE 3.7 Simplified equivalent circuit of a two-winding transformer in positive
phase sequence and negative phase sequence networks.
transformers on a per-phase basis. It must be mentioned here, however, that

the equivalent circuit shown in Figure 3.6 is actually valid only in positive
phase sequence networks and in negative phase sequence networks. A slightly
different equivalent circuit must used in zero phase sequence networks. The
meanings of these terms will be explained in Section 3.6.
Since typical values of magnetizing reactance are several orders of mag-
nitude greater than typical values of leakage reactance, and since no-load
losses are usually much smaller than load losses when the transformer is car-
rying rated load, the elements G m and X m can be neglected in most calculations.
If voltages and currents are expressed in per unit instead of using actual system
voltages and currents, the ideal transformer in the model will have a 1:1 turns
ratio and can thus be eliminated from the equivalent circuit. Since R p , R s , X p ,
and X s are now all directly in series with each other, the resistance elements
can be combined into a single resistance R and the reactance elements can be
combined into a single reactance X. The result is a much-simplified equivalent
circuit for the positive-sequence and negative-sequence networks, as shown
in Figure 3.7.
The equivalent circuits of transformers modeled in zero phase sequence
networks are different from those in positive and negative phase sequence
networks. The zero-sequence equivalent circuit depends on the type of wind-
ing connections used; these equivalent circuits will be developed a little later
in this chapter.
Before continuing with transformer equivalent circuits, it is necessary
at this point to digress with a brief tutorial on symmetrical components.
3.6 A BRIEF TUTORIAL ON SYMMETRICAL

COMPONENTS
The symmetrical component method is one of several methods that can be
used to analyze unbalanced three-phase systems. The theory of symmetrical
components is presented in many electrical engineering textbooks; unfortu-

nately, there are few textbooks that present this topic in a practical and useful
way that can easily be understood. Therefore, a brief tutorial on symmetrical
components is presented here that will provide an understanding of positive,
negative, and zero phase sequence voltages and currents and how the concept
of symmetrical components is applied to transformers.
When three-phase circuits are balanced, calculations of voltages and cur-
rents are simple and straightforward. In these instances, the actual circuit and
its positive phase sequence network are one and the same thing. The positive
phase sequence network is nothing more than a network where the phase rota-
tion is positive (normally A-B-C ) and the phases are balanced; i.e., the voltages
of all three phases have the same magnitudes, the currents of all three phases
have the same magnitudes, and the phase angles’ three phases are 120° apart.
Although the ideal set of balanced conditions may exist (approximately)
under normal conditions, this is rarely the case for design-limiting conditions
such as system faults. When voltages, currents, or impedances are unbalanced,
the solutions become much more complex, especially when there is mutual
induction between various parts of the circuit, as in the case of three-legged
core form transformers with the three phases coupled magnetically through
the core.
There have been several methods for attacking three-phase circuit prob-
lems for unbalanced conditions, but the most successful method in use today
is called symmetrical components. In this method, an unbalanced circuit is
represented by a combination of three balanced circuits, called sequence net-
works. The positive phase sequence network has already been described
above. In the negative phase sequence network, the voltages and currents of
all three phases are balanced but the phase rotation is opposite to the positive
phase sequence; i.e., if the positive phase sequence is A-B-C, then the negative
phase sequence is C-B-A. It is usually assumed that there are no negative or
zero phase sequence voltage sources.
In the zero-phase sequence network, the voltages and currents of all
three phases are identical and are all in phase with each other; i.e., there is
no phase rotation. Since the phase currents are in phase, these add together
at the neutral. Therefore, zero phase sequence networks always involve neutral
or ground currents. Zero-sequence currents exist only if there are physical
ground current paths in the circuit.
A set of unbalanced phase currents, I a , I b , and I c , may be transformed
into a set of symmetrical components I 0 , I 1 , and I 2 , where I 0 is the zero phase
sequence current, I 1 is the positive phase sequence current, and I 2 is the nega-
tive phase sequence current. The transformation is accomplished using the
following set of equations:

I 0 # 1/3 (I a % I b % I c) (3.6.1)
I 1 # 1/3 (I a % I b ∠120° % I c ∠240°) (3.6.2)
I 2 # 1/3 (I a % I b ∠240° % I c ∠120°) (3.6.3)
The transformations shown in Eqs. (3.6.1) to (3.6.3) result in sequence
currents that are referenced to A phase. There is also a set of sequence currents
that is referenced to B phase, and a set of sequence currents referenced to C
phase as well. The symmetrical component method does not require explicitly
solving all three sets of sequence currents, because these sets of sequence
currents are identical to each other except that they are shifted in phase. There-
fore, it is implicitly understood that the sequence currents I 0 , I 1 , and I 2 are
always referenced to A phase.
To transform a set of (A phase) sequence currents back into phase cur-
rents, the following equations are used:
Ia # I0 % I1 % I2 (3.6.4)
I b # I 0 % I 1 ∠240° % I 2 ∠120° (3.6.5)
I c # I 0 % I 1 ∠120° % I 2 ∠240° (3.6.6)
Voltages are transformed from phase values to sequence values and vice versa
using exactly the same formulas, except that E quantities are substituted for
I quantities in the equations. So far, it may seem that all this has accomplished
is additional work; however, the additional work usually makes calculations
involving unbalanced circuits much easier than dealing with phase quantities
alone. We will see a direct application of this method at the end of this chapter.
The following steps summarize the technique of symmetrical compo-
nents:
1. Construct the Thévenin equivalent circuits of the positive, negative,
and zero phase sequence networks at the point of the fault.
2. Connect the Thévenin equivalent circuits constructed in step 1 to-
gether at the point of the fault, and calculate the sequence voltages
and currents in all three networks at the point of the fault.
3. Transform the sequence voltages and currents at the point of the
fault calculated in step 2 back into phase voltages and currents using
Eqs. (3.6.4) to (3.6.6).
The Thévenin equivalent sequence networks are connected in different
ways in step 2 in order to analyze various kinds of faults and unbalanced
conditions. Three common unbalanced conditions are the single phase to

FIGURE 3.8 Sequence network connections for the three most common unbalanced
conditions.

ground fault, a phase-to-phase connection through an impedance, and an im-
pedance in series with one phase. The corresponding sequence network con-
nections for these unbalanced conditions are shown in Figure 3.8.
The physical circuits are represented by the rectangles along the left
of the figure. The positive, negative, and zero phase sequence networks are
represented by the rectangles labeled %, $, and 0.
3.7 TRANSFORMER EQUIVALENT CIRCUITS

MODELED IN ZERO PHASE SEQUENCE
NETWORKS
Earlier in this chapter we developed the two-winding transformer equivalent
circuit for the positive and negative phase sequence networks, as shown in
Figure 3.7. This equivalent circuit is suitable for virtually any two-winding
transformer, regardless of whether Y, ∆, or zigzag connections are used and
regardless of the type of core construction used. We shall soon see that in zero
sequence networks, the transformer equivalent circuits can be very different
depending on the connections and type of core construction. This section will
show how to develop the zero phase sequence equivalent circuits for the vari-
ous types of transformers.
The basic equivalent circuit consists of series impedance elements be-
tween the primary and secondary windings, and a shunt impedance. The shunt
impedance is approximately equal to the open-circuit impedance Z oc measured
at the primary windings with the secondary windings open-circuited, or mea-
sured at the secondary windings with the primary windings open-circuited. If
per-unit values are used, Z oc is approximately the same whether it is measured
at the primary or secondary winding. The basic zero phase sequence trans-
former equivalent circuit is shown in Figure 3.9.
As we will soon see, the value of the shunt impedance is radically differ-
ent for different types of core construction and winding connections.
If voltages are balanced and have an A-B-C or a C-B-A phase rotation,
then Z oc seen from the high-voltage side of the transformer is given by the
following equation:
1
Z oc # R p % jX p % (3.7.1)
G m $ jX m$1
The quantities G m and X m are the magnetizing conductance and reactance. In

most cases G m is practically zero and the magnitude of X m is much greater
than the magnitudes of R p and X p . Therefore, the open-circuit impedance of

FIGURE 3.9 Equivalent circuit of a two-winding transformer in a zero phase se-
quence network.
a transformer in positive or negative phase sequence networks is approxi-

mately equal to the magnetizing impedance:
Z oc ! jX m (3.7.2)
In zero phase sequence networks, Z oc is also approximately equal to jX m for
banks of three single-phase transformers; three-phase, five-legged core form
transformers; and shell form transformers connected in a Y-Y.
For transformers connected Y-∆ and for three-phase, three-legged core
form transformers connected Y-Y, the zero- sequence Z oc is much smaller than
the magnetizing impedance. In the case of a Y-∆ transformer bank, replacing
the individual transformers with their equivalent circuits and applying a zero-
sequence voltage to the primary connection easily shows this. The result is
that there are three current paths of a similar nature: current flows from the
H1 terminal through the transformer’s series impedance elements, out the X1
terminal into the secondary delta connection, back through the X2 terminal
of a transformer of a different phase, and out through that transformer’s H2
terminal to ground. The arrows in Figure 3.10 show one of these current paths.
Therefore, the open-circuit zero-phase sequence impedance of a Y-∆
connected transformer on a per-phase basis is essentially equal to the series
impedance of the transformer. The series impedance of a transformer is a small
fraction (typically 5 to 10%) of the transformer base impedance. Recalling
from Chapter 2 that a Y-∆ transformer is used as a grounding bank, it is now
easy to understand how the grounding bank works. The Y-connected primary

FIGURE 3.10 A Y-∆ transformer bank excited by a zero phase sequence voltage
with the arrows showing the three current paths.
winding presents only a small impedance to zero phase sequence currents,

which are the same as ground currents.
A similar result applies to the open-circuit impedance of a three-phase,
three-legged core form transformer with the winding Y connected. When a
zero phase sequence voltage E 0 is applied across all three windings, the mag-
netizing flux in the three phases arrive at the top core yoke in phase with each
other without any physical magnetic return path to the bottom core yoke be-
sides air. Since the path through air has a very high reluctance, the winding
impedance (which is inversely proportional to the reluctance) is quite low,
typically around 40 to 50% of the transformer’s impedance base.
In the three-phase, five-legged core design, the flux generated by Y-
connected windings excited by a zero phase sequence voltage E 0 will encoun-
ter a low-reluctance path through the outer core legs. Consequently, the open-
circuit impedance of the Y-connected winding in a zero phase sequence

network is about the same as the magnetizing impedance at low excitation
levels.
A three-phase, three-legged core form transformer is shown in Figure
3.11 on the left. A five-legged core form transformer is shown in Figure 3.11
on the right. Zero phase sequence voltages excite both of these transformers.
The zero phase sequence flux paths are shown as dotted lines.
In a five-legged core form transformer, the outer core legs and top and
bottom core yokes do not usually have enough cross-sectional area to carry
all of the flux of one phase. Since the zero-sequence flux of all three phases
are in phase with each other, the core will go to into saturation if a zero-
sequence exciting voltage is near the rated voltage.
This same effect exists for three-phase shell form transformers when
excited by zero-sequence voltages. The lateral core legs between the phases
are sized to carry the flux of one phase; however, the flux doubles when the
zero-sequence fluxes from two phases arrive in phase at the lateral core legs.
This could easily drive the core into saturation. Therefore, Z oc for both five-
legged core form and three-phase shell form transformers may decrease dra-
matically if excited by zero-sequence voltages near 100% of the rated voltage.
The exact value of Z oc is uncertain at best in these cases.
The series transformer impedance for zero phase sequence networks also
depends on how the transformer is connected. For a Y-Y connection with the
FIGURE 3.11 A three-legged core form transformer and a five-legged core form
transformer excited by a zero phase sequence voltage showing the flux paths (dotted
lines).

neutrals brought out, the series impedance in zero phase sequence networks is
approximately the same as the series impedance in the positive phase sequence
equivalent circuit. For ∆-Y and Y-∆ connections and for Y-Y connections
with the neutrals not brought out, the series transformer impedance in the zero
phase sequence equivalent circuit is infinite because there are no neutral paths
for zero-sequence currents to flow. The diagrams in Figure 3.12 show the zero
phase sequence equivalent circuits for various transformer connections.
Z H % Z X is equal to the leakage reactance plus the primary and secondary
winding resistances. Typical values for power transformers are between 7 and
15% of the transformer impedance base. As previously discussed, the mag-
netizing impedance Z M varies depending on the core construction. For three-
legged core form transformers, Z M is typically between 40 and 50% of the
transformer impedance base. For five-legged core form and three-phase shell
form transformers, Z M has very large values if the applied zero-sequence volt-
age is small, but Z M decreases rapidly if the core goes into saturation as the
applied zero-sequence voltage approaches 100% of rated voltage. Saturation
occurs because the zero-sequence fluxes in the three core legs add in phase
instead of canceling each other. This situation can occur when a Grd.Y- Grd.Y
transformer is energized by a three-phase source with an open phase.
Example 3.2
There are five spare three-phase Y-Y low tension network (LTN) transformers
and three-phase pad mount transformers that may be either three-legged core
form or 5-legged core form designs. It is desired that the types of core con-
struction of these transformers be determined prior to putting them into ser-
vice. Using a single-phase 120 VAC 60 Hz source and an ammeter, devise a
test to determine which types of core construction these transformers have.
The three high-voltage bushings (H1, H2, and H3) are jumpered together
and connected to the ‘‘hot’’ leg of the 120 VAC 60 Hz source in series with
the ammeter. The neutral bushing (H0) was connected to the grounded neutral
leg of the 120 VAC source. The low-voltage bushings were open-circuited.
The following current measurements were recorded for the five transfor-
mers.
Transformer 1
1500 KVA 12470Y-480Y
Kuhlman S/N 2–37930 Live-Front Pad
5.75% Impedance
I # 88 mA

FIGURE 3.12 Zero phase sequence equivalent circuits for four common three-phase
transformer connections.

Transformer 2
300 KVA 12470Y-208Y
Whse S/N 85JG73093 Dead-Front Pad
1.92% Impedance
I # 18 mA
Transformer 3
500 KVA 13000Y-216Y
G.E. S/N H323543P71AA LTN
4.83% Impedance
I # 21 mA
Transformer 4
300 KVA 12470Y-208Y
Allis Chalmers S/N 1729698 LTN
4.7% Impedance
I # 1.43 A
Transformer 5
G.E. S/N F645103-67P LTN
4.94% Impedance
I # 25 mA
Transformer 1 was verified to have a five-legged core design through a

physical inspection of the core and coil assembly. Based on the measured
currents, all the transformers have zero-sequence open-circuit currents less
than 100 mA with the exception of transformer 4, which had a zero-sequence
open-circuit current of 1.43 A. Based on the fact that its current is so much
higher than the other transformers, it is concluded that transformer 4 is a three-
legged core form transformer while the other transformers have the five-legged
core form design.
Example 3.3
Calculate the zero-sequence open-circuit impedance Z oc of the three-legged
core form transformer 4 and the five-legged core form transformer 1 in Exam-
ple 3.2, expressing Z oc as a per-unit impedance value of the transformer base
impedance.
Transformer 4
Full-load current # 1.732 ! 100,000 VA per phase/12,470 V # 13.89 A per
phase

The measured open-circuit current is 1.43/3 A per phase # 0.477 A per phase.
Z oc # (1.732 ! 120 V/12,470 V ) ! (13.89 A/0.49 A) # 0.472 per unit
Transformer 1
Full-load current # 1.732 ! 500,000 VA per phase/12,470 V # 69.45 A per
phase
The measured open-circuit current is 0.088/3 A per phase # 0.0293 A per
phase.
Z oc # (1.732 ! 120 V/12,470 V ) ! (69.45 A/0.0293 A) # 39.5 per unit
Referring to the zero-sequence equivalent circuit shown in Figure 3.9,
Z oc is equal to Z H % Z shunt. It is easily seen in this example how the zero-
sequence equivalent circuits are affected by the core design.
3.8 SERIES IMPEDANCE AND REGULATION

The series impedance of a transformer consists of a resistance that accounts
for the load losses and a reactance that represents the leakage reactance. This
impedance has a very low power factor, consisting almost entirely of leakage
reactance with only a small resistance. As discussed earlier, the transformer
design engineer can control the leakage reactance by varying the spacing be-
tween the windings. Increasing the spacing ‘‘decouples’’ the windings and
allows more leakage flux to circulate between the windings, increasing the
leakage reactance.
While leakage reactance can be considered a transformer loss because
it consumes reactive power, some leakage reactance is necessary to limit fault
currents. On the other hand, excessive leakage reactance can cause problems
with regulation. Regulation is often defined as the drop in secondary voltage
when a load is applied, but regulation is more correctly defined as the increase
in secondary output voltage when the load is removed. The reason that regula-
tion is defined this way is that transformers are considered to be ‘‘fully
loaded’’ when the secondary output voltage is at the rated secondary voltage.
This requires the primary voltage to be greater than the rated primary voltage
at full load.
Let E p equal the primary voltage and let E s equal the secondary voltage
when the transformer is fully loaded. Using per-unit values instead of primary
and secondary voltage values, the per-unit secondary voltage will equal E p
with the load removed. Therefore, the definition of regulation can be expressed
by the following equations.
Ep $ Es
Regulation # (3.8.1)
Es

Since E s # 1 by definition,
Regulation # E p $ 1 (3.8.2)
Regulation depends on the power factor of the load. For a near-unity power
factor, the regulation is much smaller than the regulation for an inductive load
with a small lagging power factor.
Example 3.4
A three-phase 1500 KVA 12470Y-208Y transformer has a 4.7% impedance.
Calculate the three-phase fault current at the secondary output with the primary
connected to a 12,470 V infinite bus. Calculate the regulation for a power
factor of 90% at full load.
The three-phase fault is a balanced fault, so the positive-sequence equiv-
alent circuit applies. The full-load secondary current is calculated as follows:
I # 1.732 ! 500,000 VA per phase/208 V # 4167 A per phase
The per-unit fault current is the primary voltage divided by the series imped-
ance:
1
# 21.27 per unit
0.047
The secondary fault current is equal to the per-unit fault current times the full-
load current:
I f # 21.27 per unit ! 4167 A per phase # 88,632 A per phase
To calculate regulation, the secondary voltage is 1∠0° per unit by definition.
Applying a 1 per unit load at a 90% lagging power factor, I # 1.0∠$25.8°.
Since the series impedance is mainly inductive, the primary voltage at full
load E p can be calculated as follows:
E p # 1∠0° % 1.0∠$25.8° ! 0.047∠90°
# 1.02 % j0.042 # 1.021 per unit
Regulation # E p $ 1 # 0.021 # 2.1%
3.9 MATCHING TRANSFORMERS FOR

PARALLEL AND BANK OPERATIONS
The following rules must be obeyed in order to successfully connect two or
more transformers in parallel with each other:

1. The turns ratios of all of the transformers must be nearly equal.
2. The phase angle displacements of all of the transformers must be
identical.
3. The series impedances of all transformers must be nearly equal,
when expressed as ‘‘%Z’’ using the transformer impedance base.
The first two rules are required so that the open-circuit secondary volt-
ages of the transformers are closely matched in order to avoid excessive circu-
lating currents when the parallel connections are made.
The last rule is based on the fact that for a given voltage rating and %Z,
the ohmic impedance of a transformer is inversely proportional to its KVA
rating. When transformers having the same %Z are connected in parallel, the
load currents will split in proportion to the KVA ratings of the units. Therefore,
transformers with different KVA ratings can be successfully operated in paral-
lel as long as their %Z values are all approximately the same.
Example 3.5
(This example is based on an actual event.)
Two three-phase 10,000 KVA 66,000∆-12,470Y volt transformers were
in parallel operation in a substation. The primaries of the two transformers
are connected to a 66 kV transmission line through a single air break switch.
This switch is designed to interrupt magnetizing current only, which is less
than 1 A. The transformers were being removed from service and the second-
ary loads had been removed. A switchman then started to open the air break
switch, expecting to see a small arc as the magnetizing current was interrupted.
Instead, there was a loud ‘‘bang’’ and there was a ball of flame where the air
break switch contacts had vaporized. Something was obviously wrong.
Upon closer inspection, it was revealed that the two transformers had
been set on widely different taps: The first transformer was on the 62,700 V
primary tap and the second transformer was on the 69,300 V primary tap.
Both transformers had a 7% impedance. Because the turns ratios were unequal,
a circulating current was set up even without any secondary load. The open-
circuit secondary voltage difference, assuming 66 kV at the transformer pri-
maries, is calculated below.
∆E s # 66,000 !
" 12,470 12,470
$
62,700 69,300 #
V # 1250 V # 0.10 per unit
The per-unit circulating current in the secondary loop is equal to ∆E s divided

by the sum of the per-unit impedances of the two transformers:

0.10
Ic # # 0.714 per unit
0.14
Converting I c into amperes:
I c # 0.714 ! 10,000 KVA/(12.47 kV ! 1.732) # 331 A per phase
Since I c flows in a loop in the secondary circuit, the current out of the
secondary of the first transformer equals the current into the secondary of the
second transformer. But since the turns ratios are not equal, I c does not get
transformed into equal and opposite currents at the primaries.
12,470
Primary current of first transformer # 331 A !
62,700
# 65.8 A per phase
12,470
Primary current of second transformer # 331 A !
69,300
# 59.6 A per phase
The net current through the air break switch, I AB , is the difference in the pri-
mary currents:
I AB # 65.8 A per phase $ 59.6 A per phase # 6.2 A per phase
The current through the air break switch supplies the I 2c X s reactive losses of
both transformers and therefore lags the primary voltage by 90°. The resulting
current exceeded the interrupting rating of the switch, causing it to fail. The
conditions described in this example are diagramed in Figure 3.13.
3.10 IMPEDANCE MISMATCH IN THREE-

PHASE TRANSFORMER BANKS
When connecting single-phase transformers in three-phase banks, proper im-
pedance matching becomes even more critical. In addition to following the
three rules for parallel operation, it is also a good practice to try to match the
X/R ratios of the three series impedances to keep the three-phase output volt-
ages balanced.
If single-phase transformers are connected in a Y-Y bank with an iso-
lated neutral, then the magnetizing impedances should also be equal on an
ohmic basis. Otherwise, the transformer having the largest magnetizing imped-
ance will have a highest percentage of exciting voltage, increasing the core
losses of that transformer and possibly driving its core into saturation.

FIGURE 3.13 Circuit diagram for Example 3.5 showing circulating currents for par-
allel transformers with different turns ratios.
When single-phase transformers with the same KVA ratings are con-
nected in a Y-∆ bank, impedance mismatches can cause a significant load
unbalance among the transformers. The general case where all three transform-
ers have different impedances is derived below.
Define the following ratios of impedances, w and x, as follows. (Note:
In general, these ratios are complex numbers because the impedances are com-
plex numbers.)
Zb
w$ → Z b # wZ a (3.10.1)
Za
Zc
x$ → Z c # xZ a (3.10.2)
Za
With a balanced three-phase load of 1 per unit applied, the phase currents are
as follows (see Figure 3.14):
i 1 # 1∠0° (3.10.3)
i 2 # 1∠240° (3.10.4)
i 3 # 1∠120° (3.10.5)

FIGURE 3.14 Y-∆ transformer bank made up with three single-phase transformers
having different impedances.
The voltage drop around the closed ∆ path must equal zero:
i a Z a % i b Z b % i c Z c # i a Z a % i b wZ a % i c xZ a # 0 (3.10.6)
ia % w ib % x ic # 0 (3.10.7)
The load currents can be expressed in terms of the transformer currents i a , i b ,
and i c :
i a $ i b # i 1 # 1∠0° (3.10.8)
i c $ i a # i 3 # 1∠120° (3.10.9)
The transformer secondary currents are solved from the last three equations:
w∠0° $ x∠120°
ia # (3.10.10)
1%w%x
x∠240° $ 1∠0°
ib # (3.10.11)
1%w%x
1∠120° $ w∠240°
ic # (3.10.12)
1%w%x
The bank is balanced if w # 1 and x # 1. Even when the impedance magni-
tudes are all equal, if the X/R ratios are unequal then w ≠ 1 or x ≠ 1 and the
transformer currents will not be equal. The most heavily loaded transformer

FIGURE 3.15 Chart showing the loading of a Y-∆ transformer bank made up with
three single-phase transformers as a function of the impedance imbalance between two
of the phases and the third phase.
limits the maximum load that can be applied to the bank, so any unbalance
will reduce the load rating of the bank.
Let us examine the specific case where the X/R ratios of all three trans-
formers are equal, and transformer B is identical to transformer C but the
impedance of transformer A is not equal to the impedances of the other two
transformers. In this case Z b /Z a # Z c /Z a # x and x is a real number. The
currents i a , i b , and i c are multiplied by 1.732 to obtain the per-unit loading due
to the Y-∆ connection. The graph in Figure 3. 15 plots the per-unit transformer
loadings as x varies over the range 0.1 to 10.
3.11 TEMPERATURE RISE AND THE

THERMAL CAPABILITY
Transformer KVA ratings have been alluded to on a number of occasions up
to this point without explaining how the KVA rating is determined. The KVA
rating of a transformer is simply the steady-state KVA load applied to the
output of the transformer at the voltage rating of the output winding that pro-
duces an average winding temperature rise (above the ambient temperature)
equal to 65°C. For older transformers, the rated average winding temperature
rise was 55°C. Advances in insulating materials allowed a 10°C increase in
average temperature. The temperature rise of the winding is caused by all of
the transformer losses that were previously discussed in this chapter. There-
fore, the winding temperature is a function of load losses and no-load losses.

The thermal capability of a transformer is defined in a slightly different
way from the rated KVA. Thermal capability is the KVA load applied to the
output of a transformer that causes the hottest area in the windings, called the
winding hot spot, to reach some limiting temperature. The hot-spot tempera-
ture determines the rate of loss of life of the transformer as a whole, which
is a cumulative effect. Therefore, the hot-spot temperature limit is usually
based on a loss-of-life criterion. The standard method for calculating the ther-
mal capability of oil-insulated transformers will be covered fully at the end
of this chapter.
3.12 INTERPRETING TRANSFORMER TEST

REPORTS
Much of the information needed to calculate temperature rise and the thermal
capability of a transformer is contained in the transformer test report. When
one purchase order is used to procure a number of identical transformers from
the same manufacturer, some testing is performed on each transformer while
certain other tests are performed only on one representative unit in that pur-
chase order. There is a recommended format of a transformer test report [1].
Some transformer manufacturers follow the recommended format exactly
while others prefer to use their own format, but the information contained in
the test reports is standard throughout the industry.
A sample test report is shown in Figure 3.16. It was based on an actual
factory test report for an order of four transformers used in a generating station.
A certified test engineer would sign the actual transformer test report, testi-
fying to its authenticity. In the upper portion of the test report is the general
design information, such as the cooling class, number of phases, frequency
rating, rated temperature rise, voltage ratings of the windings, and the KVA rating.
The transformers shown in Figure 3.16 have an FOA Cooling Class, which is
an abbreviation for forced-oil-air. This means that heat is transferred from the
core and coils to the insulating oil, which is forced through the transformer by
oil pumps. The heat is then transferred from the insulating oil to the ambient air
through a set of radiators which have air forced through them by fans.
The voltage rating of the HV winding is 512500Grd.Y/296000, which
means the primary winding is designed to be Y connected to a system having
a phase-to-phase voltage of 512.5 kV and a phase-to-neutral voltage of 296
kV. The ‘‘Grd.’’ designation usually indicates that the winding has reduced
insulation near the neutral end, the neutral being normally grounded. The full
winding rating from phase to ground is 296,000 V. Additional HV winding
taps are available at 538,125, 525,312, 499,688, and 486,875 V.
The voltage rating of the LV winding is 23600, which means that it is

FIGURE 3.16 Sample test report for four transformers on a single purchase order.

designed to be ∆-connected to a system having a phase-to-phase voltage of
23.6 kV. The full winding rating is the same as the phase-to-phase system
voltage, 23,600 V.
We can glean a lot of additional information from this test report:
• The core losses represent about 24% of the total losses.
• The core losses increase by over 50% when the applied voltage in-
creases by 10% over the rated voltage.
• The resistance portion is only about 1.6% of the total series imped-
ance, so the series impedance can be approximated by the leakage
reactance.
• The transformers are over 99% efficient at full load.
• All of the electrical characteristics of the four transformers are re-
markably similar.
The methods used in performing factory tests will be covered in more detail
in Chapter 8. ‘‘W.M. Copper Loss’’ is an abbreviation for watt meter copper
loss. Since typical magnetizing current power factors are extremely small, core
loss measurements require carefully calibrated test equipment.
At the bottom of the test report are the results of a heat run test. The heat
run test applies a load equal to the nameplate KVA rating of the transformer at
full voltage using an inductive load. Using an inductive load reduces the en-
ergy use during this test. Nonetheless, the energy requirements for supplying
the transformer losses alone can be significant for large transformers. It is an
expensive and time-consuming test, so it is usually only performed on one of
the transformers on a purchase order. In the case of this sample test report in
Figure 3.16, the heat run was only performed on Serial Number C-05213-5-
4 and the results can then be used to calculate the thermal capabilities of the
other transformers on this purchase order.
It was intended in the original design to build a transformer having a
65°C average winding temperature rise when continuously loaded at the
405,000 KVA nameplate rating. Note from the test report, however, that the
HV winding only attained a 59.4°C rise and the LV winding only attained a
50.5°C rise. Therefore, the as-built transformer has a 5.6°C temperature design
margin that can be used to increase the loading above the nameplate rating. It
is this increased loading, and not the nameplate rating, that is the true thermal
capability of that transformer. The average winding temperatures are not di-
rectly measured in this test. Instead, the winding temperatures are inferred
from conductor resistance measurements taken immediately after the test is
shut down. The dc resistance of a metallic conductor is a linear function of the
conductor’s absolute temperature. The temperature of a transformer winding is

not uniform along the length of the conductor; however, the resistance mea-
surement of the total conductor will provide the average temperature of the
winding.
The last two entries on the test report are the hot spot temperature rise
of the HV and LV windings. These values are not actually measured by any
test, but are calculated based on the average winding temperature and the oil
temperature. There is only about a 6.5°C temperature gradient between the hot
spot temperature and the average winding temperature. This is fairly typical of
transformers in the FOA cooling class. Since cooling oil is forced through the
windings by pumps, the oil velocity is quite high. The high oil velocity tends
to equalize the oil temperatures along the flow paths through the windings.
For transformers without oil pumps, such as the self-cooled (OA class) or
forced-air cooled only (FA class), the oil velocities are much slower and there
is a much greater temperature gradient between the hot spot temperature and
the average winding temperature.
3.13 CALCULATING THE HOT-SPOT

TEMPERATURE USING THE IEEE
METHOD
The following series of equations outlines the algorithm used to compute tem-
peratures in oil-filled transformers [2]. This method can be applied to trans-
formers of any MVA size. The ambient temperature is assumed to be constant
and all temperatures shown are in °C. The hot-spot temperature θ H is the tem-
perature that determines the thermal capability of the transformer and is given
by the following equation.
θ H # θ A % ∆θ TO % ∆θ H (3.13.1)
where
θ A # ambient temperature
∆θ TO # temperature gradient of the top oil temperature over the ambient tem-
perature
∆θ H # temperature gradient of the hot spot over the top oil temperature
The top oil temperature θ TO is calculated as follows:
θ TO # θ A % ∆θ TO (3.13.2)
If the load changes from one value to another,
∆θ TO # (∆θ TO,U $ ∆θ TO,i)(1 $ e $t/τTO) % ∆θ TO,i (3.13.3)

where
∆θ TO,U # ultimate steady-state top oil temperature gradient

∆θ TO,i # initial top oil temperature gradient
t # duration of the load change, h
τ TO # oil time constant, h
" #
n
K 2i R % 1
∆θ TO,i # ∆θ TO,R (3.13.4)
R%1
where
R # ratio of load losses at rated load to no-load losses from the test report
K i # ratio of the initial load to the rated load
∆θ TO,R # top oil temperature gradient at rated load from the test report
n # an empirical exponent that depends on the cooling class
A generally accepted value for n is 0.8 for OA cooling class transformers, 0.9
for the FA and FOA cooling classes, and 1.0 for directed flow FOA or FOW
(forced oil and water) cooling classes.
" #
n
K 2U R % 1
∆θ TO,U # ∆θ TO,R (3.13.5)
R%1
where K U # the ratio of the ultimate (final) load to the rated load.
The winding hot-spot temperature gradient is also load and time depen-
dent:
∆θ H # (∆θ H,U $ ∆θ H,i)(1 $ e $t/τ W) % ∆θ H,I (3.13.6)
where
∆θ H,U # ultimate steady-state hot-spot temperature gradient

∆θ H,i # initial hot spot temperature gradient
t # duration of the load change, h
τW # winding time constant, h
∆θ H,i # ∆θ H,R ! K 2m
i (3.13.7)
where
∆θ H,R # the hot-spot temperature gradient at rated load from the test report
m # an empirical exponent depending on the cooling class

A generally accepted value for m is 0.8 for the OA, FA, and FOA cooling
class transformers and 1.0 for the directed flow FOA or FOW (forced oil and
water) cooling classes.
The oil time constant τ TO is calculated as follows: Let C # the thermal
capacity of the transformer. For OA and FA cooling classes,
C # 0.06 ! W CC % 0.04 ! W TF % 1.33 ! GO Wh/°C (3.13.8)
and for the FOA cooling class,
C # 0.06 ! W CC % 0.06 ! W TF % 1.93 ! GO Wh/°C (3.13.9)
where
W CC # weight of the core and coil assembly, lb
W TF # weight of the tank and fittings, lb
GO # total gallons of oil that cools the transformer
∆θ TO,R
τ TO,R # C ! (3.13.10)
P T,R
where P T,R # total loss at rated load from the test report.
∆θ TO,U /∆θ TO,R $ ∆θ TO,i /∆θ TO,R
τ TO # τ TO,R ! (3.13.11)
(∆θ TO,U /∆θ TO,R) 1/n $ (∆θ TO,i /∆θ TO,R) 1/n
The calculation of the winding time constant τ W is not described in the
IEEE standard. Most engineers consider the winding time constant to be very
short, and a value of zero is used by some. Although the IEEE method seems
rather complicated, it is straightforward enough with the use of a desktop
computer. The IEEE standard includes a computer program in Basic code that
performs the temperature calculations.
For a load that cycles periodically, the following method is used to calcu-
late temperatures:
• The load is approximated by a series of step changes. Satisfactory
results can be obtained with just a few step changes over the course
of 24 h, but better accuracy will be achieved if the load cycle is
broken into 1 h intervals.
• A set of initial temperatures is assumed for the beginning of the load
cycle and the temperatures at the end of the first load step are calcu-
lated using Eqs. (3.13.1) to (3.13.7).
• This process is repeated for each of the load steps until the end of
the cycle is reached.

• This process is repeated for each of the load steps until the end of
the cycle is reached.
• The process is then repeated for the entire load cycle, using the tem-
peratures calculated at the end of each load cycle as the initial tem-
peratures of the next load cycle.
• Eventually, after perhaps two or three cycles, the temperatures at the
end of the load cycle converge to the same values at the end of every
cycle.
• When this state is reached, the solution has converged.
3.14 CALCULATING THE LOSS OF LIFE

Industry standards also address the loss of life of a transformer due to tempera-
ture and aging. The relation of insulation aging to time and temperature fol-
lows the well-known Arrhenius chemical reaction rate model.
The adaptation used in the IEEE standard [3] has the following form.
Per unit life # Ae B/(θH%273) (3.14.1)
where θ H # winding hot-spot temperature in °C, and A and B are constants.
The meaning of per unit life is illustrated as follows: If per unit life #
2, then the transformer would be expected to last twice the ‘‘normal’’ life. If
per unit life # 0.5, then the transformer would be expected to last only half the
‘‘normal’’ life. Normal life for most transformers is considered to be around 30
to 40 years.
The constants A and B depend on the types of material used to insulate
the windings. Since cellulose in the form of kraft paper is the most common
insulation material, these constants have been worked out empirically:
Per unit life # 9.8 ! 10 $18 e 15000/(θH%273) (3.14.2)
The winding hot-spot design temperature to attain a normal life is 110°C. This
is based on an assumed ambient temperature of 30° plus the 65°C average
winding temperature gradient over ambient plus a 15°C allowance for the hot-
spot gradient over the average winding temperature. Using θ H # 110°C yields
a per unit life # 1.
The aging acceleration factor F AA is the ratio of the per unit life at the
design temperature of 110°C divided by the per unit life at some operating
temperature θ H .
The constant A then divides out:
F AA # e 15000/383$15000/(θH%273) # e 39.16$15000/(θH%273) (3.14.3)

To calculate the equivalent aging of the transformer F EQA with a varying
hot-spot temperature such as occurs for a cycling load or a seasonal ambient
temperature, F AA is integrated over time and the integral is divided by the total
time to obtain the average.
The per unit life and F AA are plotted vs. hot-spot temperature in the chart
It should be stressed that most transformer failures are random events
that occur for various reasons besides insulation loss of life. Therefore, the
formula for per unit life cannot be used as a predictive model to determine
when a given transformer will ultimately fail. However, it is indeed certain
that overloading a transformer will shorten its life, so it is a good practice from
FIGURE 3.17 The per unit life and the aging acceleration factor as a function of
the hot-spot temperature.

a reliability standpoint to keep the loading within the transformer’s thermal
capability.
Example 3.6
Using the transformer test report shown in Figure 3.16, calculate the hot-spot
temperature of transformer S/N C-05213–5-1 at 2 h after the load is changed
from 350 MVA to 450 MVA, assuming the initial load was applied for a
long time prior to the change. Use the IEEE temperature calculation method
assuming a constant 30°C ambient temperature. The following additional data
apply to these transformers: weight of core and coils (W CC) # 346,000 lb;
weight of tank and fittings (W TF) # 64,500 lb; gallons of oil (GO) # 13,400.
Assume the cooling class is FOA with directed flow.
From the test report, it is clear that the HV winding has the higher tem-
perature and is the limiting winding. The initial and ultimate temperatures are
calculated first:
909,932 W
R# # 3.244 from the test report
280,488 W
350 MVA
Ki # # 0.864
405 MVA
∆θ TO,R # 39.0°C from the test report
n # m # 1.0
" #
n
K 2i R % 1
∆θ TO,i # ∆θ TO,R # 31.4°C
R%1
∆θ H,R # 67.1°C $ 39.0°C # 28.1°C from the test report
∆θ H,i # ∆θ H,R ! K 2m
i # 21.0°C
450 MVA
KU # # 1.111
405 MVA
" #
K 2U R % 1 n
∆θ TO,U # ∆θ TO,R # 46.0°C
R%1
∆θ H,U # ∆θ H,R ! K 2m
U # 34.7°C
The thermal time constant is calculated next (for the FOA cooling class):
C # 0.06 ! W CC % 0.06 ! W TF % 1.93 ! GO # 50,492 Wh/°C
P T,R # 1,190,420 W from the test report
τ TO,R # C ! ∆θ TO,R /P T,R # 1.65 h

Since n # 1.0,
τ TO # τ TO,R # 1.65 h
Calculating ∆θ TO at t # 2 h:
∆θ TO # (∆θ TO,U $ ∆θ TO,i)(1 $ e $t/τTO) % ∆θ TO,i # 41.7°C
Calculating ∆θ H by assuming the winding time constant is zero:

∆θ H # ∆θ H,U # 34.7°C
The final result:
θ H # θ A % ∆θ TO % ∆θ H # 106.4°C at 2 h
Example 3.7
Using the results from Example 3.6, what are the per unit life and the F AA
if 450 MVA are applied continuously, assuming a constant 30°C ambient tem-
perature?
The final steady-state hot-spot temperature θ H,U is based on the ultimate
temperature rise of the oil and the ultimate hot-spot gradient:
θ H,U # θ A % ∆θ TO,U % ∆θ H,U
# 30°C % 46.0°C % 34.7°C # 110.7°C
Per unit life # 9.8 ! 10 $18 e 15000/(θ H,U%273) # 0.93
F AA # e 39.16$15000/(θH,U%273) # 1.07
At the 450 MVA loading, the transformer loses life at a rate 7% greater than
at the design temperature of 110°C. To calculate the thermal capability pre-
cisely, a trial-and-error approach is used where the MVA loading is varied
and the temperatures are calculated until the desired per unit life is achieved.
Example 3.8
Three of the transformers shown on the test report shown in Figure 3.16 are
used as a generator step-up transformer bank with the HV windings set to the
nominal taps. The generator is rated 1280 MVA at 24,000V with a positive-
sequence reactance X G1 of 0.35 per unit and a negative-sequence reactance
X G2 of 0.27 per unit. The Y-connected generator is grounded through a resis-
tance. A bolted phase-to-ground fault occurs at one of the HV terminals of
the transformer. Using the transformer impedance values shown in the ‘‘Aver-

age’’ column of the transformer test report, calculate the currents at the HV
fault and at the generator terminals.
The three-phase diagram of the actual circuit is shown in Figure 3.18.
The first step is to convert the generator and transformer impedances to a
common MVA and voltage base. In this example, we will use the generator
ratings for the common MVA base. The MVA base on a per-phase basis is
1280 MVA/3 # 426. 7 MVA per phase. Let us assume that the series winding
impedance of the transformer bank is purely reactive (all leakage reactance).
Convert the 14.17% transformer reactance to the new base:
" #
2
426.7 MVA 23,600 V
X T # 0.1417 ! ! # 0.1444 per unit
405 MVA 24,000 V
Load currents are generally neglected in fault calculations. The positive

phase sequence, negative phase sequence and zero phase sequence networks
are connected in series for a phase-to-ground fault on A phase, as shown in
FIGURE 3.18 A phase-to-ground fault at the output of the generator step-up trans-
former used in Example 3.8.

FIGURE 3.19 Sequence network connections for a phase-to-ground fault at the out-
put of a generator step-up transformer used in Example 3.8.
Figure 3.19. Note that although the phase angle of the generator is $30° in
the real system, the phase angle of the generator as observed by the HV fault
is phase shifted by %30° because of the standard ∆-Y connection with the
HV side leading the LV side. Thus, the phase angle of the generator is 0° in
the positive-sequence Thévenin equivalent circuit. Note also that the generator
grounding resistance and the generator zero-sequence impedance are irrelevant
to the calculation since there is no ground current through the transformer
secondary circuit because of the ∆ connection.
Calculating the HV sequence currents,
1.0 1
I0 # I1 # I2 # #
jX G1 % jX G2 % 3jX T j0.35 % j0.274 % j0.4332
# 0.946∠$90° per unit
Converting the HV sequence currents into phase currents,
I A # I 0 % I 1 % I 2 # 3 ! 0.946∠$90° per unit

# 2.838∠$90° per unit
I B # I 0 % I 1 ∠240° % I 2 ∠120° # 0
I C # I 0 % I 1 ∠120° % I 2 ∠240° # 0
After the voltage base of the LV system is chosen, the voltage base of the
HV system must be determined by the transformer voltage ratio and cannot
be chosen arbitrarily.
Determining the voltage base of the HV system:
V base # 24,000 V ! (512,500 V/23,600 V) # 521,186 V
Converting I a,b,c into amperes,
I base # 1.732 ! 426,000,000 VA/521,186 V # 1416 A per phase
I a # 2.838∠$60° per unit ! 1416 A # 4019∠$90° A
Ib # Ic # 0
Transforming the HV current into LV currents at the generator:
i a # I a ! (296,000 V/23,600 V) # 50,408∠$90° A
i b # $i a # 50,408∠90° A
ic # 0
Note that the transformer turns ratio is 296,000/23,600 and not 512,500/
23,600 in the last step because the ratio of the winding voltages must be used
instead of the ratio of system voltages when transforming voltages and currents
from the primary to the secondary.
Example 3.9
A T-connected transformer is used to supply a balanced two-phase secondary
load from a three-phase supply. The two-phase load current is 1 per unit in
each secondary winding. Calculate the positive, negative, and zero phase se-
quence currents in the three-phase circuit in per unit.
The T connection uses a 1:1 transformer between A phase and neutral
to supply one-half of the two-phase load and a 1.732 :1 transformer between
C phase and B phase to supply the other half of the two-phase load. The
1:1 transformer has a load current of 1∠90° on the secondary side and the
1.732: 1 transformer has a load current of 1∠0° on the secondary side. On
the three-phase primary side the A phase current is 1∠90°, the B phase current
is 0.577∠0°, and the C phase current is 0.577∠180°.

Converting the phase currents into sequence currents:
ia % ib % ic
Zero sequence: i0 # # 0.333∠90°
3
i % i b ∠120° % i c ∠240°
Positive sequence: i1 # a # 0.666∠90°
3
i % i b ∠240° % i c ∠120°
Negative sequence: i2 # a #0
3
Example 3.10
A test circuit for a 2000 KVA three-phase 12470Grd.Y/7200 $ 208Grd.Y/
120V transformer is shown in Figure 3.20. The ammeter reads 0.2 A and
the voltmeter reads 120 V. Calculate the open-circuit zero phase sequence
impedance of this transformer, in per unit of the transformer rating.
Full load current per phase at 7200 V:
I FL # 2,000,000 VA/(3 phases ! 7200 V) # 92.6 A/phase
Zero phase sequence current at 120 V:
I 0 # 0.2 A/3 # 0.0667 A/phase

Z 0 # E/I # (120 V/7200 V) ! (92.6 A/0.0667 A) # 23.1 per unit
This is essentially the same as Z shunt in the equivalent zero-sequence circuit.
FIGURE 3.20 Test connections used in Example 3.10.

Example 3.11
Three single-phase transformers are connected as a Y-∆ transformer bank. The
transformers have the following nameplate ratings:
Transformer A: 100 KVA 7200–480 5% Z
Transformer B: 100 KVA 7200–480 6% Z
Transformer C: 150 KVA 7200–480 5% Z
A 300 KVA balanced three-phase load is applied to the ∆-connected output.
Calculate the per-unit load in each transformer on its own base.
Using the method described in Section 3.10:
Z b 0.06
w# # # 1.2
Z a 0.05
Z 0.05/150 KVA
x# c# # 0.667
Z a 0.05/100 KVA
The per unit currents solved for the ∆-connected secondary must be multiplied
by 1.732 to be expressed in per-unit loads on a 100 KVA base. Additionally,
the current in transformer C must be divided by 1.5 to express the per unit
load on a 150 KVA base.
w∠0° $ x∠120°
i a # 1.732 !
1%w%x
# 0.989∠$20.6° per unit of 100 KVA
x∠240° $ 1∠0°
i b # 1.732 !
1%w%x
# 0.878∠203.4° per unit of 100 KVA
1∠120° $ w∠240°
i c # 1.732 !
1 % w % x/1.5
# 0.770∠87.0° per unit of 150 KVA
Example 3.12
A 150 MVA Class FOA transformer has the following test data:
Copper losses at full load 940,000 W
Core losses at 100% voltage 150,000 W
Oil temperature rise 39.0°C
HV hot-spot temperature rise 68.1°C
LV hot-spot temperature rise 59.1°C

Using the IEEE method, calculate the aging acceleration factor F AA for
this transformer for a constant load of 165 MVA with an ambient temperature
of 25°C. From transformer test data:
∆θ TO,R # 39.0°C
∆θ H,R # 68.1°C $ 39.0°C # 29.1°C
KU # 165 MVA/150 MVA # 1.1
R # 940,000 W/150,000 W # 6.23
n # 0.8 for FOA cooling class
m # 0.9 for FOA cooling class
" #
n
K 2U R % 1
∆θ TO,U # ∆θ TO,R !
R%1
" #
0.8
1.1 2 ! 6.23 % 1
# 39.0°C
6.23 % 1
# 44.6 °C
∆θ H,U # ∆θ H,R K 2m
U # 29.1°C ! 1.1
1.8
# 34.5°C
θ A # 25°C
θ H # θ A % ∆θ TO,U % ∆θ H,U # 25.0°C % 44.6°C % 34.5°C # 104.1°C
F AA # e 39.16 $ 15000/(θH % 273) # 0.54
Example 3.13
Three single-phase transformers are connected in a ∆-Grd.Y generator step-
up transformer bank with the generator connected to the ∆ side of the bank.
Two of the transformers each have a 15% impedance, and the third transformer
has a 20% impedance on a common base. A balanced load current of 1 per
unit with a 90% lagging power factor is applied at the output of the trans-
former. What are the positive-, negative-, and zero-sequence voltages at the
generator?
The primary of the transformer is modeled as three ideal transformers
with series impedances of j0.15, j0.15 for B and C phases, and j0.20 for A phase.
The voltages across the windings are E a , E b , and E c . The voltages at the HV
terminals are by definition 1∠0°, 1∠240°, and 1∠120° with the 1 per unit
currents 25.8° lagging with respect to the voltages. Refer to Figure 3.21.

FIGURE 3.21 Diagram used in Example 3.13.
E a # 1∠0° % 0.2∠64.2° # 1.102∠9.4°

E b # 1∠240° % 0.15∠304.2° # 1.074∠247.2°
E c # 1∠120° % 0.15∠184.2° # 1.074∠127.2°
Converting to sequence voltages:
Ea % Eb % Ec
Zero sequence: E0 # # 0.0168∠64.5°
3
E a % E b ∠120° % E c ∠240°
Positive sequence: E 1 # # 1.083∠7.9°
3
E % E b ∠240° % E c ∠120°
Negative sequence: E 2 # a # 0.0168∠64.5°
3
The zero-sequence voltage is blocked by the ∆ connection on the generator
side of the transformer. The positive-sequence and negative-sequence voltages
are transformed by the ∆-Grd.Y bank, so at the generator these voltages are:
Zero sequence 0
Positive sequence 1.083 per unit
Negative sequence 0.0168 per unit

REFERENCES
1. National Electrical Manufacturers Association. Transformers, Regulators and Re-
actors. NEMA Standards Publication No. TR 1-1980, Part 7, pp. 3–5.
2. Institute of Electrical and Electronics Engineers, Inc. An American National Stan-
dard, IEEE Guide for Loading Mineral-Oil-Immersed Power Transformers Up to
and Including 100 MVA with 55°C or 65°C Average Winding Rise. IEEE Std.
C57.92-1981, pp. 68–69.
3. Institute of Electrical and Electronics Engineers, Inc. An American National Stan-
dard, IEEE Guide for Loading Mineral-Oil-Immersed Power Transformers Up to
and Including 100 MVA with 55°C or 65°C Average Winding Rise. IEEE Std.
C57.92-1981, pp. 10–11.

4
Autotransformers and Three-
Winding Transformers
In this chapter, the principles of the two-winding transformer are extended

and applied to two special and very important types of transformers: the auto-
transformer and the three-winding transformer.
4.1 AUTOTRANSFORMER CONNECTIONS

The autotransformer is both the most simple and the most fascinating of the
connections involving two windings. It is used quite extensively in bulk power
transmission systems because of its ability to multiply the effective KVA ca-
pacity of a transformer. Autotransformers are also used on radial distribution
feeder circuits as voltage regulators. The connection is shown in Figure 4.1
The autotransformer shown in Figure 4.1 is connected as a boosting
autotransformer because the series winding boosts the output voltage. Care
must be exercised when discussing ‘‘primary’’ and ‘‘secondary’’ voltages in
relationship to windings in an autotransformer. In two-winding transformers,
the primary voltage is associated with the primary winding, the secondary
voltage is associated with the secondary winding, and the primary voltage is
normally considered to be greater than the secondary voltage. In the case of

FIGURE 4.1 The boosting autotransformer connection. The output terminals operate
at a higher voltage than the input terminals.
a boosting autotransformer, however, the primary (or high) voltage is associ-

ated with the series winding, and the secondary (or low) voltage is associated
with the common winding; but the voltage across the common winding is
higher than across the series winding.
The other possible connection for an autotransformer is shown in Figure
4.2. The autotransformer shown in Figure 4.2 is connected as a bucking auto-
transformer because the series winding bucks, or opposes, the output voltage.
The key feature of an autotransformer is that the KVA throughput of
the transformer, i.e., its capacity, is different than the KVA transformed by
the common and series windings. The common and series windings are wound
on the same core leg, so the transformer laws presented in Chapter 1 still
apply:
FIGURE 4.2 The bucking autotransformer connection. The output terminals operate
at a lower voltage than the input terminals.

1. The volts per turn in the common winding equal the volts per turn
in the series winding. The common winding voltage divided by the
series winding voltage is equal to the number of turns in the com-
mon winding divided by the number of turns in the series winding.
2. The sum of the ampere-turns of the common winding plus the am-
pere-turns of the series winding equal the magnetizing ampere-
turns. The magnetizing ampere-turn are practically zero, so the mag-
nitude of the ampere-turns in the common winding is approximately
equal to magnitude of the ampere-turns in the series winding. The
series winding current divided by the common winding current is
equal to the number of turns in the common winding divided by
the number of turns in the series winding.
3. The KVA transformed in the series winding equals the KVA trans-
formed in the common winding.
The capacity multiplication effect stems from the fact that the metallic connec-
tion between the input and output circuits allows part of the KVA to flow
though the connection and bypass the transformation. This is illustrated in the
following example.
Example 4.1
A boosting autotransformer has a common winding voltage of 7200 V and a
series winding voltage of 1400 V. The current low-voltage input current is
100 A. Determine the KVA throughput and the KVA transformed. Refer to
Figure 4.3.
KVA throughput ! 7.2 kV " 100 A ! 720 KVA
KVA common ! KVA series ! KVA transformed
7200 V " (100 A # I 0) ! 1400 V " I 0
720 KVA
I0 ! ! 83.72 A
8600 V
KVA common ! 7.2 kV " (100 A # 83.72 A)
! 117.2 KVA
KVA series ! 1.4 kV " 83.72 A ! 117.2 KVA
In Example 4.1, the ratio of KVA throughput to KVA transformed is
720/117.2 ! 6.1, meaning that this autotransformer has 6.1 times the capacity
of a two-winding transformer of a similar size and weight. This is a consider-
able multiplication of KVA capacity.

FIGURE 4.3 A boosting autotransformer used in Example 4.1.
Example 4.2
Repeat Example 4.1 for the same windings using a bucking connection instead
of a boosting connection with the same 100 A input current. Refer to Figure
4.4
KVA throughput ! 7.2 kV " 100 A ! 7200 KVA
KVA common ! KVA series ! KVA transformed
7200 V " I c ! 1400 V " (100 $ I c) → I c ! 24.14 A
KVA common ! 7.2 kV " 24.14 A ! 173.8 KVA
KVA series ! 1.4 kV " (100 A $ I c) ! 173.8 KVA
In Example 4.2, the ratio of KVA throughput to KVA transformed is
720/173.8 ! 4.1 so the capacity multiplication factor for the bucking connec-
tion is not quite as great as that of the boosting connection.
The capacity multiplication factor F c is a function of the ratio of the
output voltage to the input voltage r. For a boosting transformer:
r
Fc ! (4.1.1)
r#1
and for a bucking autotransformer:
1
Fc ! (4.1.2)
r#1

FIGURE 4.4 A boosting autotransformer used in Example 4.2.
For boosting autotransformers and bucking autotransformers, F c is very large

when r ! 1. F c for a boosting autotransformer is always greater than 1, and
it is always greater than F c for a bucking autotransformer for a given value
of r. The chart shown in Figure 4.5 plots F c versus r for the boosting and
bucking connections.
FIGURE 4.5 The capacity factor of an autotransformer F c as a function of the voltage

transformation ratio r. The heavy curve is for a boosting autotransformer and the lighter
curve is for a bucking autotransformer.

The bucking connection is never used unless r ! 1 because F c falls
off very rapidly as r increases. A boosting autotransformer begins to lose its
advantage over a two-winding transformer as the voltage ratio increases. For
r % 10, there is practically no advantage at all.
4.2 IMPEDANCE OF AN
AUTOTRANSFORMER
The impedance of a transformer can be determined by measuring the imped-
ance across the primary terminals with the secondary terminals short-circuited.
Consider a two-winding transformer having a turns ratio n connected as a
boosting autotransformer. The transformer impedance, which is mainly leak-
age reactance, is split between the common winding and the series winding
as Z c and Z s , respectively. The magnetizing impedance is neglected. To deter-
mine the impedance of the autotransformer, the secondary (low-voltage) termi-
nals are short-circuited and a voltage source E p is applied to the primary (high-
voltage) terminals, as shown in Figure 4.6.
The current through the common winding I c is equal to the current
through the series winding divided by the turns ratio:
Is
Ic ! (4.2.1)
n
The voltage across the common winding E c is equal to the voltage drop across
Zc:
Zc
Ec ! Ic " Zc ! Is " (4.4.2)
n
FIGURE 4.6 A boosting autotransformer with a short circuit applied at the low-volt-
age output.

The voltage across the series winding E s is equal to E c divided by the turns
ratio:
Ec Z
Es ! ! I s " 2c (4.2.3)
n n
The current through the series winding I s is equal to the difference between
the input voltage E p and the voltage across the series winding E s divided by
Zs:
Ep # Es
Is ! (4.2.4)
Zs
Multiplying both sides of Eq. (4.2.4) by Z s and substituting Eq. (4.2.3)
for E s :
Zc
Is " Zs ! Ep # Is " (4.2.5)
n2
Solving for E p by rearranging Eq. (4.2.5):
"
Ep ! Is " Zs $
Zc
n2 # (4.2.6)
The impedance as seen at the primary or high-voltage side of the trans-

former Z p is equal to E p /I s . This is obtained by dividing both sides of Eq.
(4.2.6) by I s :
Zc
Zp ! Zs $ (4.2.7)
n2
Notice that the value of Z p in Eq. (4.2.7) is equal to the series impedance
as seen at the secondary or low-voltage side when the transformer is connected
as a conventional two-winding transformer with the high-voltage windings
short circuited. For a large ratio n this impedance is much smaller than the
series impedance seen at the primary side.
In general, the series impedance of a small two-winding transformer is
greater than the series impedance of a large two-winding transformer if the
two impedances expressed as percent of the winding KVA bases are equal.
However, when a small transformer is connected as an autotransformer the
series impedance seen at the transformer terminals can be substantially smaller
than the impedance of a much larger equivalent two-winding transformer. This
can be quantified as follows. Let:

% Z AT ! impedance of a unit connected as autotransformer expressed in
percent of the winding KVA base
KVA AT ! winding KVA base a unit connected as an autotransformer
% Z TW ! impedance of a two-winding transformer expressed in percent
of the winding KVA base
KVA TW ! winding KVA base of a two-winding transformer
Z AT ! impedance, in ohms, of an autotransformer across the primary
terminals
Z TW ! impedance, in ohms, of a two-winding transformer across the
primary terminals
r ! ratio of the primary terminal voltage to the secondary terminal
voltage
n ! turns ratio of the common/series windings of the
autotransformer
E p ! primary voltage
E s ! autotransformer series winding voltage
η ! ratio of Z AT/ Z TW
The impedance of a transformer in ohms is equal to the per unit imped-

ance times the quantity E 2base /KVA base . Recall from Eq. (4.2.7) that the imped-
ance of an autotransformer seen at the primary terminals is equal to the series
impedance as seen at the secondary or low-voltage side when the transformer
is connected as a conventional two-winding transformer. Therefore, E base !
E s , and
Z AT ! 0.01 " %Z AT " E 2s /KVA AT ohms (4.2.8)
For a two-winding transformer, E base ! E p, and
E 2p
Z TW ! 0.01 " % Z TW " ohms (4.2.9)
KVA TW
The ratio Z AT /Z TW is found by dividing Eq. (4.2.8) by Eq. (4.2.9).
Z AT E 2 " KVA TW " %Z AT

! 2s (4.2.10)
Z TW E p " KVA AT " %Z TW
If the two-winding transformer is replaced by an autotransformer having

the same KVA capacity, the KVA rating of the autotransformer windings is
smaller than the KVA rating of the two-winding transformer windings. Recall-
ing the capacity multiplication factor of a boosting autotransformer in Eq.
(4.1.1),

r
KVA TW /KVA AT ! F c ! (4.2.11)
r#1
For the boosting autotransformer connection, the secondary voltage is equal
to the voltage across the common winding. The voltage across the series wind-
ing E s divided by the secondary voltage is therefore equal to 1/n:
Es 1
! (4.2.12)
secondary voltage n
The ratio r was defined as the primary terminal voltage divided by the second-
ary terminal voltage:
Ep
!r (4.2.13)
secondary voltage
For a boosting autotransformer,
1
! r # 1, (4.2.14)
n
Es r#1
! (4.2.15)
Ep r
(r # 1) 2
(E s /E p) 2 ! (4.2.16)
r2
Combining Eqs. (4.2.11) and (4.2.16) with Eq. (4.2.10), the following
result is obtained.
(r # 1) " %Z AT
η! (4.2.17)
r %Z TW
Since %Z AT and %Z TW are expressed on the KVA bases of the transformer
windings, the values of these values should be comparable even though the
physical sizes and KVA ratings of the transformers may be very different.
For the special case where %Z AT and %Z TW are equal,
r#1
η! &1 (4.2.18)
r
The meaning of Eq. (4.2.18) is that the engineer has the opportunity to design
an autotransformer with much lower conductor losses and regulation than
would be practical with a two-winding transformer with the same KVA capac-
ity. However, in order to limit short-circuit currents, the reactance compo-

nent of the impedance must still be maintained above some minimum design
limit. In Section 4.4, we will see that an autotransformer behaves very differ-
ently from a two-winding transformer when a short-circuit is applied to the
output.
Example 4.3
A certain three-phase autotransformer has a 50,000 KVA capacity and a
primary to secondary voltage rating of 230,000/132,791Grd.Y-69,000/
39,837Grd.Y. In order to limit fault current to less than 7 per unit, the system
design engineer specified a 15% impedance on a 50,000 KVA base. Determine
the required %Z of the windings, based on the KVA rating of the windings
and not the KVA capacity of the autotransformer, in order to provide the
required 15% impedance.
In this instance, impedance of the autotransformer is equal to the imped-
ance of the equivalent two-winding transformer, both being 15% on a 50,000
KVA base and having the same impedance in ohms.
Z AT ! Z TW
η!1
From Eq. (4.2.17),
(r # 1) " %Z AT
η!
r " %Z TW
230,000
r! ! 3.333
69,000
η! 1#
" # 1
r
"
%Z AT
%Z TW
!1
Solving for % Z AT ,
%Z TW 15%
% Z AT ! ! ! 21.4%
1 # 1/r 1 # 0.3
Example 4.4
Suppose the series impedance of the autotransformer in Example 4.1 is 10%
of its winding KVA base. What is the impedance of the autotransformer ex-
pressed as a percent of the KVA capacity of the autotransformer?
In Example 4.1, the winding KVA base is equal to 117.2 KVA that is

transformed. The autotransformer’s capacity is equal to its 720 KVA
throughput Equation (4.2.18) gives the impedance (in ohms) of the autotrans-
former divided by the impedance (in ohms) of an equivalent two-winding
transformer if both transformers have the same percent impedance values of
their winding KVA bases. This ratio is calculated below.
r#1
η!
r
8600 V
r! ! 1.194
7200 V
1.194 # 1
η! ! 0.162
1.194
The ratio η given by Eq. (4.2.18) is also equivalent to the ratio of the
percent impedance of the autotransformer divided by the percent impedance
of an equivalent two-winding transformer, when both percent impedances are
expressed on the same KVA base. In other words, the 117.2 KVA two-winding
transformer with a 10% impedance in this example can be connected as a
boosting autotransformer and the autotransformer’s impedance will be 1.62%
of the 117.2 KVA base.
When the autotransformer’s impedance is expressed on a 720 KVA base,
the resulting impedance is still lower.
117.2 KVA
%Z ! 1.62% " ! ! 0.264%
720 KVA
Since transformer load losses can be seen as a resistance component of the

series impedance, the load losses of the autotransformer are on the order of
0.00264 times the load losses of a larger two-winding transformer with a simi-
lar coil design. This example clearly illustrates the tremendous savings in
economy that can be realized by using the autotransformer connection.
Example 4.5
A 7200–120 V two-winding transformer has a 7% impedance based on the
winding ratings. The transformer is connected as a single-phase boosting auto-
transformer in a single-phase radial distribution circuit. What is the % imped-
ance based on the capacity of the autotransformer connection?
The input to the autotransformer is 7200 V single phase. The output
from the autotransformer is 7200 V $ 120 V ! 7320 V single phase.

7320
r! ! 1.01667
7200
At the output side of the autotransformer, the impedance of the auto-
transformer is the impedance of the series winding, or 7% on a 120 V base.
Converting to a 7320 V base:
" #
2
120
%Z ! 7% " ! 0.00188%
7320
The KVA capacity of the transformer in the boosting autotransformer

connection is increased by the factor r/(r # 1). Converting the impedance to
the autotransformer KVA capacity base,
r 1.01667
%Z ! 0.00188% " ! 0.00188% " ! 0.115%
r#1 0.01667
4.3 LIMITATIONS OF THE

AUTOTRANSFORMER CONNECTION
One of the limitations of the autotransformer connection is that not all types
of three-phase connections are possible. For example, the ∆-Y and Y-∆ con-
nections are not possible using the autotransformer. The Y-Y connection must
FIGURE 4.7 A hypothetical ∆-∆ autotransformer connection showing the phase

angle displacement between the high-voltage and low-voltage terminals. For this rea-
son, this autotransformer connection is seldom, if ever, used.

share a common neutral between the high-voltage and low-voltage windings,
so the neutrals of the circuits connected to these windings cannot be isolated.
The Grd.Y-Grd.Y connection using autotransformers is indistinguishable from
a Grd.Y-Grd.Y connection using two-winding transformers. This is the most
common connection using autotransformers.
A ∆-∆ autotransformer connection is theoretically possible; however,
this will create a peculiar phase shift. The phase shift is a function of the ratio
of the primary to secondary voltages and it can be calculated from the vector
diagram, such as the example shown in Figure 4.7. This phase shift cannot
be changed or eliminated and for this reason, autotransformers are very seldom
connected as ∆-∆ transformers.
4.4 AUTOTRANSFORMER VOLTAGES

WITH SHORT CIRCUITS APPLIED
When a short circuit is applied across the secondary terminals of a two-wind-
ing transformer, the voltages across both the primary and secondary windings
decrease because of exclusion of flux from the core, as was described in Chap-
ter 3. This is easily seen from the equivalent circuit of a two-winding trans-
former: The voltage across the magnetizing branch is reduced by approxi-
mately 50% when the secondary terminals short-circuited due to the voltage
drop across the primary series impedance, assuming the per unit primary series
impedance Z H is approximately the same as the per unit secondary series im-
pedance Z X .
The situation is very different when a short circuit is applied to an auto-
transformer, as can be seen from the circuit diagram shown in Figure 4.8. All
of the applied primary voltage E p appears across the impedance of the series
FIGURE 4.8 Measuring the series impedance of an autotransformer involves shorting

the output terminals and measuring the current at the input terminals.

winding Z s so the series current is equal to the applied voltage divided by the
impedance:
Ep
Is ! (4.4.1)
Zs
This current is transformed into current in the common winding:
Is Ep
Ic ! ! (4.4.2)
n n " Zs
The voltage across the common winding is equal to the voltage drop through
the common winding times the impedance of the common winding Z c :
E p " Zc
E c ! Ic " Zc ! (4.4.3)
n " Zs
The voltage across the common winding is transformed into a voltage E s
across the series winding.
E c E p " Zc
Es ! ! 2 (4.4.4)
n n " Zs
If the per-unit values of Z c and Z s are approximately equal, then the ratio Z c /
(n 2 " Z s) is approximately equal to 1:
Es ! Ep (4.4.5)
The series winding of an autotransformer has a normal applied voltage
that is usually only a small fraction of the applied voltage across the primary
terminals. A short circuit across the secondary terminals causes a very signifi-
cant increase in the voltages across the series winding. This almost guarantees
that the core will go into saturation, with two immediate results. First, the
admittance of the magnetizing branch of the transformer can no longer be
ignored, and the admittance of the magnetizing branch is very nonlinear with
the core in saturation; therefore, short-circuit current calculations are some-
what uncertain for autotransformers. Second, with the core in saturation, the
transformer essentially becomes an air-core transformer, further limiting the
ability to calculate impedances. Fortunately, this also limits the magnitude of
the induced voltage across the common winding. So although the voltage
across the series winding may be several times the normal operating voltage
of this winding, the overvoltage across the common winding is not quite as
severe.

4.5 IMPULSE VOLTAGES APPLIED
TO AUTOTRANSFORMERS
Another feature of the autotransformer needs to be dealt with; namely, when
a voltage surge travels along the primary circuit and hits the series winding,
nearly all of the surge voltage is applied across the series winding. This is
because the relatively large line-to-ground capacitance of the external second-
ary circuit prevents the voltage to build up at the secondary terminals before
the voltage surge has reached its peak at the primary terminals. Because the
turns ratio between the common and series winding is usually large, a very
high voltage is also induced in the common winding. The ASA Test Code,
which was used in the past, recognized this particular disadvantage of auto-
transformers and required full impulse test voltages to be applied across each
winding in turn (see Ref. 1.)
The modern IEEE test code does not make any special provisions for
testing autotransformers; however, the design engineer must be cognizant of
the fact that significantly higher impulse voltages may appear across the wind-
ings of an autotransformer as compared to a two-winding transformer.
One way that this problem can be addressed is to install surge protection
in autotransformers. Thyrite blocks are connected between the windings and
ground and across the series winding to limit applied and induced impulse
voltages. Thyrite blocks have a nonlinear resistance characteristic with the
current through the thyrite increasing sharply when the voltage exceeds a cer-
tain breakdown voltage. This tends to limit the voltage across the thyrite,
thereby protecting the windings. In a boosting autotransformer, thyrite blocks
are typically installed across the common winding, between the high-voltage
terminals and ground, and across the series winding.
As was seen in Section 4.4, the series and common windings are exposed
to excessive voltages during short-circuit conditions as well as during line
surges. The problem with using thyrite blocks or other types of surge protec-
tion in autotransformers is that the surge protection may break down under
short-circuit conditions unless their breakdown voltages are carefully coordi-
nated.
4.6 AUTOTRANSFORMER CORE

AND COIL DESIGNS AND
TERMINAL CONFIGURATIONS
Engineers sometimes conceptualize each phase of an autotransformer as a sin-
gle winding with a tap brought out and connected to the secondary circuit.

This conceptualization is electrically correct but not physically accurate, how-
ever. The voltages and currents of the series and common windings are usually
very different, so the two windings are usually designed very differently. For
example, if the series winding has fewer turns than the common winding, as
is usually the case, the series winding will carry more current and the conduc-
tors must have a larger cross-sectional area than the common winding. In very
large autotransformers the series winding may even be constructed as multiple
parallel windings.
So a typical core and coil assembly in an autotransformer will be some-
what similar to the core and coil assembly of a two-winding transformer with
the common and series windings being concentric and wound around the same
core leg. However, unlike a two-winding transformer, the series winding will
be located farthest from the core since it operates at the line potential of the
high-voltage circuit. Also, the series winding will be insulated for much higher
phase-to-ground voltages as well as much higher turn-to-turn voltages than
the secondary of a two-winding transformer in order to withstand the high
voltages across it due to line surges and secondary short circuits.
For three-phase autotransformers, all of the standard two-winding core
and coil designs are used: three-legged core form, five-legged core form, and
shell form. The major difference between the autotransformer design and the
two-winding design is in the way the windings are interconnected.
Externally, there is little difference between autotransformers and two-
winding transformers. The standard terminal arrangements apply to both types
of connections. The only difference is that with an autotransformer, the X0
and H0 terminals must be brought out through a common neutral bushing.
This neutral bushing is sometimes labeled the H0/X0. Single-phase autotrans-
formers can still be additive or subtractive, and the external locations of the
bushing terminals still follow the standard configuration; however, since auto-
transformers tend to have large KVA ratings, they are usually subtractive
polarity.
4.7 ADVANTAGES AND DISADVANTAGES

OF THE AUTOTRANSFORMER
CONNECTION
Summarizing the advantages of the autotransformer connection:
• There are considerable savings in size and weight.

• There are decreased losses for a given KVA capacity.

• Using an autotransformer connection provides an opportunity for
achieving lower series impedances and better regulation.
Summarizing the disadvantages of the autotransformer connection:
• The autotransformer connection is not available with certain three-
phase connections.
• Higher (and possibly more damaging) short-circuit currents can re-
sult from a lower series impedance.
• Short circuits can impress voltages significantly higher than op-
erating voltages across the windings of an autotransformer.
• For the same voltage surge at the line terminals, the impressed and
induced voltages are greater for an autotransformer than for a two-
winding transformer.
In many instances, the advantages of the autotransformer connection outweigh
its disadvantages. For example, when very large MVA capability is required
and where a Grd.Y-Grd.Y connection is suitable, an autotransformer is usually
the design of choice. Because an autotransformer cannot provide a ∆-Y con-
nection, autotransformers are not suitable for use as generator step-up trans-
formers.
4.8 THREE-WINDING TRANSFORMERS

The three-winding transformer is a subset of multiwinding transformers. In
addition to the usual primary and secondary windings, a third tertiary winding
is added to each phase. Having three winding can serve several purposes:
• Three windings allow connecting three systems together where each
system has a different operating voltage.
• Three windings provide electrical isolation between dual input cir-
cuits or dual output circuits having the same operating voltage.
• If the third winding is ∆-connected, this can stabilize voltages, sup-
ply third harmonic currents to magnetize the transformer core, filter
third harmonics from the system, and provide grounding bank action
when the primary and secondary windings are both Y-connected.
Sometimes a tertiary winding may serve more than one function at the
same time. For example, a 13.8 kV ∆-connected tertiary winding on a 230 kV–
69 kV Grd.Y-Grd.Y transformer helps to stabilize the primary and secondary
voltages, provides grounding bank action to partially shield the primary circuit

from secondary ground currents, and provides 13.8 kV supply voltage to a
station-service auxiliary transformer. (Note: When a group of windings are
connected in parallel to increase the current capability of a secondary winding,
the parallel group is considered one winding and not several separate wind-
ings. Using multiple sets of low-voltage windings in parallel is common in
large generator step-up transformers; however, these are still considered two-
winding transformers.)
Sometimes a tertiary winding is intended only to magnetically interact
with the primary and secondary windings so it may not have any external
terminal connections. In these cases, the tertiary winding is said to be an im-
bedded tertiary. Imbedded tertiary windings are found only in three-phase
transformers and are always ∆-connected. One corner of the ∆-connected im-
bedded tertiary winding is sometimes grounded internally to limit capacitively
coupled voltages.
For single-phase transformers, the standard labels for the tertiary bush-
ings are Y1 and Y2. For three-phase transformers, the standard labels for the
tertiary bushings are (Y0), Y1, Y2, Y3.
4.9 MODIFICATION OF TRANSFORMER

LAWS WITH THREE WINDINGS
The transformer laws developed in Chapter 1 do not fundamentally change
with the addition of a tertiary winding to the core leg. Since the tertiary wind-
ing is linked to the same flux as the primary and secondary windings, the
volts per turn of the tertiary is identical to the volts per turn of the other two
windings.
EH EX E
! ! Y (4.9.1)
NH NX NY
where
EH ! voltage across the primary winding
EX ! voltage across the secondary winding
EY ! voltage across the tertiary winding
NH ! number of turns in the primary winding
NX ! number of turns in the secondary winding
NY ! number of turns in the tertiary winding
There are now three transformer turns ratios instead of one and the first trans-
former law can be modified as follows:

E H NH
! (4.9.2)
EX NX
E H NH
! (4.9.3)
EY NY
E X NX
! (4.9.4)
EY NY
When current flows in the tertiary winding, this adds to (or subtracts
from, depending on the direction of the current) the total MMF. The total
MMF is equal to the magnetizing MMF, which being small is usually assumed
to be zero.
(i H " N H ) $ (i X " N X ) $ (i Y " N Y ) ! MMF mag ! 0 (4.9.5)

where
i H ! current in the primary winding
i X ! current in the secondary winding
i Y ! current in the tertiary winding
Since E H /N H ! E X /N X ! E Y /N Y ! constant, per Eq. (4.9.1), each of the terms
above can be multiplied by the same constant:
(i H " N H ) "
" #
EH
NH
$ (i X " N X )
(4.9.6)
"
EX
NX" #
$ (i Y " N Y ) "
EY
NY
!0
" #
This equation reduces to the following form, resulting in the modification to
the second transformer law:
(i H " E H ) $ (i X " E X ) $ (i Y " E Y ) ! 0 (4.9.7)
Equation (4.9.7) can be interpreted as an energy conservation law: The total
instantaneous power flowing into the transformer from all three windings is
zero. In a two-winding transformer, the magnitude of the KVA in the primary
winding equals the magnitude of the KVA in the secondary windings; how-
ever, in a three-winding transformer, the KVA may divide among the three
windings in an infinite number of ways, depending on the combination of
loads applied to the secondary and tertiary circuits.

4.10 EQUIVALENT CIRCUIT OF A THREE-
WINDING TRANSFORMER
Various forms of a three-winding transformer equivalent circuit have been
proposed, but the simplest and most useful is the so-called T equivalent circuit,
shown in Figure 4.9. The magnetizing branch is omitted in the T equivalent
since the magnetizing impedance is normally much greater than the series
impedances. If voltages and impedances are expressed in per unit values, then
the ideal transformers can sometimes be omitted also; however, in some cases
1: 1 ideal transformers are retained so that the connections to the primary,
secondary and tertiary circuits can be properly represented by the equivalent
circuit.
In a three-winding transformer, eddy-current losses occur in each wind-
ing from stray flux produced by the other two windings, even if the third
winding is not carrying any load. Therefore, each series resistance element in
the T equivalent circuit of a three-winding transformer represent eddy-current
losses produced by currents in other windings. Hence, a series resistance does
not belong to any particular winding but is distributed among all three widings.
To derive the series impedance values in the T equivalent circuit, imped-
ance measurements are made of each pair of windings taken two at a time.
One winding is short-circuited with voltage applied to the other winding while
the third winding is open-circuited. The current is measured through the wind-
ing with the applied voltage. The impedance is equal to the applied voltage
divided by that current. The test setup to measure the impedance between the
H and X windings of a single-phase three-winding transformer is shown in
Figure 4.10.
FIGURE 4.9 T equivalent circuit of a three-winding transformer.

FIGURE 4.10 Measuring Z HX of a three-winding transformer.
The test for a three-phase, three-winding transformer is similar except

that three-phase voltages are used. There are three sets of measurements taken.
The first set of measurements applies a three-phase voltage to the H1, H2,
and H3 terminals with the X1, X2, and X3 terminals shorted together and the
Y1, Y2, and Y3 terminals open. The second set of measurements applies a
three-phase voltage to the H1, H2, and H3 terminals with the Y1, Y2, and
Y3 terminals shorted together and the X1, X2, and X3 terminals open. Finally,
a three-phase voltage is applied to the X1, X2 and X3 terminals with the Y1,
Y2, and Y3 terminals shorted together with the H1, H2, and H3 terminals
open.
The Z HX , Z HY , and Z XY impedance values are determined by dividing the
voltages by the currents in each test. The series impedances of the T equivalent
circuit are calculated using the following equations.
Z HX $ Z HY # Z XY
ZH ! (4.10.1)
2
Z HX $ Z XY # Z HY
ZX ! (4.10.2)
2
Z HY $ Z XY # Z HX
ZY ! (4.10.3)
2
One of the windings of a three-winding transformer may have a much
smaller KVA rating than the other two windings but the series impedance of
that winding may have about the magnitude as the series impedances of the
other two windings. If the winding having the smallest rating is short-circuited,
the current in that winding may be much greater than its ‘‘short-circuit with-

stand capability’’ unless the impedance of that winding is increased. This can
be done by physically placing the winding farther away from the other wind-
ings to increase the leakage flux. There are practical limitations to doing this,
however, so the lowest-rated winding is usually no less than 35% of the rating
of the other windings in order to withstand the effects of short circuits.
It is possible for one of the impedances in the T equivalent to have a
negative impedance value. This occurs if one of the values of Z XY , Z HY , or Z HX
is greater than the sum of the other two values. This condition makes one of
the values of Z H , Z X , or Z Y negative, but only one of these can be negative in
the same transformer. When connecting single-phase three-winding transform-
ers in a bank, it is extremely important that all of the impedance values are
matched; otherwise, unbalanced operation will result. A branch with a high
negative impedance can also affect ground relaying.
Factory tests for a three-phase Y-Y-∆ transformer will usually include
zero phase sequence impedance measurement. This measurements is done by
jumpering the H1, H2, and H3 bushings together and applying a single-phase
voltage between these bushings and the H0 bushing while measuring the re-
sulting zero phase sequence current. The value of Z 0 on a per-phase basis is
equal to the applied voltage divided by one-third of the total current.
4.11 CORE AND COIL CONSTRUCTION OF

THREE-WINDING TRANSFORMERS
The primary, secondary, and tertiary windings of each phase are physically
wound on a common core leg. Any of the two-winding core and coil designs
are used for three-winding transformers, including single-phase core form;
single-phase shell form; three-phase, three-legged and five-legged core form;
and three-phase shell form designs. In core-form designs, it is customary to
place the winding with the lowest operating voltage nearest to the grounded
core, with the intermediate-voltage winding wound around it, and the high-
voltage winding wound around the intermediate-voltage winding. Since the
tertiary winding is often the winding with the lowest operating voltage, it
would follow that the tertiary winding would be closest to the core. Because
it is sometimes necessary to design the tertiary winding with a high series
impedance to limit the short-circuit current, occasionally the tertiary is wound
around the high-voltage and low-voltage windings to increase the leakage flux
for this winding and create a high leakage reactance between the tertiary and
the other two windings. The placement of the windings will measurably affect
the distribution of impedances in the T equivalent circuit.

Example 4.6
Three single-phase transformers are connected in a Grd.Y-Grd.Y-∆ trans-
former bank. The primary and secondary windings both have the same MVA
rating and are both connected Grd.Y. The tertiary winding MVA ratings are
35% of the primary ratings. The transformers have the following per unit
impedances.
Transformers A and B: Z HX ! 0.14 Z HY ! 0.35 Z XY ! 0.20

Transformer C: Z HX ! 0.14 Z HY ! 0.20 Z XY ! 0.35
All impedances are assumed to be purely reactive and are expressed in

per unit of the MVA base of the primary and secondary windings. There is
no external load on the tertiary circuit and the primary voltages are balanced.
Describe what happens when balanced three-phase load currents are applied
to the secondary windings of this transformer bank.
Calculating the HV, LV, and TV impedances for transformers A and B:
Z HX $ Z HY # Z XY 0.14 $ 0.35 # 0.20

ZH ! ! ! 0.145 per unit
2 2
Z $ Z XY # Z HY 0.14 $ 0.20 # 0.35
Z X ! HX ! ! #0.005 per unit
2 2
Z $ Z XY # Z HX 0.35 $ 0.20 # 0.14
Z Y ! HY ! ! 0.410 per unit
2 2
Calculating the HV, LV, and TV impedances for transformer C:
Z HX $ Z HY # Z XY 0.14 $ 0.20 # 0.35

ZH ! ! ! #0.005 per unit
2 2
Z $ Z XY # Z HY 0.14 $ 0.35 # 0.20
Z X ! HX ! ! 0.145 per unit
2 2
Z HY $ Z XY # Z HX 0.35 $ 0.20 # 0.14
ZY ! ! ! 0.410 per unit
2 2
The T equivalent circuit of the transformer bank in Example 4.6 is shown in

Figure 4.11. Because the position of the negative-impedance leg for trans-
former C is reversed in its T equivalent circuit, a voltage unbalance is produced
when currents flow. The voltage unbalance is proportional to the load current.
This causes a circulating current I y to flow through in the tertiary windings.

FIGURE 4.11 Bank of three-winding transformers with unbalanced series imped-
ances used in Example 4.6.
For 1.0 per unit balanced load currents, the circulating current in this example
is just under 0.16 per unit. This can be verified by the student by solving the
loop equations shown in Figure 4.11. Since the tertiary rating is 0.35 per unit
(35% of the primary winding MVA rating), this circulating current will not
overload the tertiary windings.

4.12 THERMAL CAPABILITY OF THREE-
WINDING TRANSFORMERS
Calculation of the thermal capability of a two-winding transformer is straight-
forward because the magnitude of the KVA in the primary winding equals
the KVA in the secondary winding. The calculation of the thermal capability
of a three-winding transformer is complicated by the fact that the KVA loads
of the three windings may be different and are unpredictable. In fact, a precise
calculation of the thermal capability using the methodology in IEEE Standard
C57.92-1981 is generally not possible unless certain simplifying assumptions
are made. Usually, the tertiary load is either assumed to have a constant load
equal to the rating of the tertiary winding or is assumed to have a load equal
to the secondary load.
When the primary winding supplies all of the input KVA, it will carry
the sum of the secondary and tertiary loads. In this case, the transformer ther-
mal capability is based on the thermal capability of the primary winding as
long as neither the secondary load nor tertiary load exceed specified limits.
For example, a 100 MVA transformer may have a specified limit of 70 MVA
on either the secondary or tertiary, so the transformer can be safely loaded
with 70 MVA on the secondary and 30 MVA on the tertiary, with 30 MVA
on the secondary and 70 MVA on the tertiary, or with 50 MVA on the second-
ary and 50 MVA on the tertiary, and so on.
4.13 THE STABILIZING EFFECT

OF A ∆ TERTIARY WINDING
A ∆-connected tertiary winding is often added to stabilize voltages with Y-
Y connections. As an example, consider a Y-Grd.Y transformer with the sec-
ondary winding grounded and the primary winding ungrounded. This connec-
tion is used to isolate the primary circuit from ground currents in the secondary
circuit; however, this connection would ordinarily produce a very bad voltage
unbalance when phase-to-neutral loads are connected to the secondary. The
root cause for the voltage unbalance is that zero-sequence currents have no
path in the primary circuit because the neutral is ungrounded. The secondary
zero-sequence currents must then encounter a relatively high magnetizing im-
pedance. Adding a ∆-connected tertiary winding solves the problem by provid-
ing grounding bank action. With a local source of ground current, the primary
circuit is not required to carry neutral current.
The diagram in Figure 4.12 shows the sequence network connections
for a bank of single-phase transformers connected Y-Grd.Y with a 1.0 per

FIGURE 4.12 Positive, negative, and zero phase sequence networks connected to
simulate a single-phase load Z L , connected to the secondary of a Y-Grd.Y transformer.
Zero sequence currents must pass through a relatively large magnetizing impedance
Z M , which produces a large zero sequence voltage E 0 .
unit single-phase-to-ground load Z L applied to phase A When the single-phase

load is supplied by a Y-Grd.Y transformer bank shown in the figure, the se-
quence networks show that all of the load current must pass through the mag-
netizing impedance Z M , which is typically much greater than 1 per unit. This
greatly limits the available load current. The sequence voltages and secondary
phase voltages for this connection are summarized below.
Z L ! 1.0 (4.13.1)
Z M %% 3 " Z L %% Z HX (4.13.2)
E 1 ! 1.0 (4.13.3)
E2 ! 0 (4.13.4)
E 0 ! #1.0 (4.13.5)
Ea ! 0 (4.13.6)
E b ! 1.73∠120° (4.13.7)
E c ! 1.73∠60° (4.13.8)

FIGURE 4.13 Positive, negative, and zero phase sequence networks connected to
simulate a single-phase load Z L , connected to the secondary of a Y-Grd.Y transformer
with a ∆-connected tertiary winding added. Zero sequence currents pass through a
relatively small series impedance Z XT between the secondary and tertiary windings.
The secondary voltage E a on the loaded phase collapses and the second-
ary voltages on the other two phases, E b and E c , approach the magnitudes of
the phase-to-phase voltages. This may drive the core into saturation and reduce
Z M ; however, a transformer with a saturated core does not behave as a normal
transformer. The actual voltages are difficult if not impossible to determine
under these conditions.
The diagram shown in Figure 4.13 shows the sequence network connec-
tions for a bank of single-phase transformers with ∆-connected tertiary wind-
ings added to create a Y-∆-Grd.Y transformer connection. A 1.0 per unit
single-phase-to-ground load is applied to phase A.
When the single-phase load is connected to a Y-∆-Grd.Y transformer
bank, the sequence networks clearly show that the tertiary windings provide
an effective ground path through the low-voltage winding to tertiary-winding
impedance Z XT . This magnitude of Z XT is slightly greater than the magnitude
of the high-voltage to low-voltage impedance, Z HX . The sequence voltages and
phase voltages are summarized below.
Z L ! 1.0 (4.13.9)
3 " Z L %% Z XT % Z HX (4.13.10)

E 1 ! 1.0 (4.13.11)
E2 ! 0 (4.13.12)
E0 ! 0 (4.13.13)
E a ! 1.0 (4.13.14)
E b ! 1.0∠240° (4.13.15)
E c ! 1.0∠120° (4.13.16)
The secondary voltage E a on the loaded phase as well as the secondary

voltages on the other two phases are maintained at about the same values as
when the transformer bank is unloaded. The tertiary winding current is equal
to the zero-sequence current, which is one-third of the A phase current. There-
fore, if the tertiary windings have a KVA rating equal to 35% of the KVA
rating of the low-voltage and high-voltage windings, then none of the windings
will be overloaded.
One of the common types of large power transformers used in bulk
power substations is a three-phase Grd.Y-Grd.Y autotransformer with a ∆-
connected tertiary winding. The purpose of the tertiary winding is to stabilize
the voltages of the Grd.Y-Grd.Y connection, so its KVA rating is around one-
third of the autotransformer’s KVA rating. This configuration can be imple-
mented either as a bank of three single-phase transformers or as a three-phase
unit. There are several inherent advantages of this design. First of all, using
an autotransformer for the main windings takes advantage of the considerable
savings in size, weight, and economy of the autotransformer. The Y-Y connec-
tion allows systems of various voltages to be tied together without introducing
phase shifts between them, and most of the inherent disadvantages of the
Y-Y connection are ameliorated by the influence of the ∆-connected tertiary.
Finally, by choosing a distribution voltage for the voltage rating of the tertiary
winding, the tertiary can supply station service or auxiliary load.
Example 4.7
The sample test report shown in Figure 4.14 is for a typical large three-winding
transformer. Using the information shown, determine the T equivalent circuit
impedance values, expressed in per unit of 84 MVA. The impedance values
shown on the nameplate are expressed on different KVA bases. Assuming that
the impedances are mostly reactive, the reactive components are calculated as
follows.

FIGURE 4.14 A typical test report for a three-winding transformer.

84 MVA
X HX ! 0.1531 " ! 0.1715 per unit
75 MVA
84 MVA
X HY ! 0.1202 " ! 0.3846 per unit
26.25 MVA
84 MVA
X XY ! 0.0670 " ! 0.1920 per unit
26.25 MVA
The reactance values between windings are converted to winding reactances
using Equations 4.10.1 through 4.10.3:
0.1715 $ 0.3846 # 0.1920
XH ! ! 0.1821 per unit
2
0.1715 $ 0.1920 # 0.3846
XX ! ! #0.02121 per unit
2
0.3846 $ 0.1920 # 0.1715
XY ! ! 0.2026 per unit
2
The resistance values shown on the test report are the sum of the three phases.
These are converted to per unit values per phase at the nominal voltage rating.
84,000,000 VA
R H ! 5.347 Ω " ! 0.00283 per unit
3 " (230,000V ) 2
84,000,000 VA
R X ! 0.2584 Ω " ! 0.00152 per unit
3 " (69,000V) 2
84,000,000 VA
R Y ! 0.06479 Ω " ! 0.0117 per unit
3 " (12,470V) 2
Z H ! R H $ jX H ! 0.00283 $ j0.1821
Z X ! R X $ jX X ! 0.00152 # j0.02121
Z Y ! R Y $ jX Y ! 0.0117 $ j0.2026
REFERENCE
1. R.L. Bean, N. Chackan, Jr., H. R. Moore, and E. C. Wentz. Transformers for the

5
Short Circuits, Inrush Currents,
and Other Phenomena
5.1 EFFECTS OF SHORT CIRCUITS

ON TRANSFORMERS
Transformers are susceptible to damage by secondary short-circuit currents
having magnitudes that can be many times rated load current. The damage
results from the following effects:
• The I 2 R losses in the winding conductors are increased by the square

of the current. This increases the temperature rise of the windings.
Because protective devices limit the duration of short circuits (as
opposed to overloads), the temperature rise of the winding can be
calculated by dividing the total energy released by the I 2 R losses by
the thermal capacity of the conductor.
• The short-circuit currents exclude flux in the core and increase stray
flux around the core. This stray flux induces currents in metallic parts
other than the winding conductors, which can be damaged thermally.
• As we saw in Chapter 4, a short circuit applied to the secondary
circuit of an autotransformer can substantially increase the voltage
across the series winding and across the common winding through

induction. This not only presents the possibility of damaging the
winding insulation by overvoltage, but will also drive the core into
saturation and significantly increase core losses with potential dam-
aging effects from temperature.
• Bushings and tap changers have current ratings that are usually only
marginally greater than the rated load of the transformer. Since fault
currents are many times rated currents and these components have
short thermal time constants, they can be seriously overloaded and
thermally damaged.
• Stray flux in the vicinity of current-carrying conductors produces
mechanical forces on the conductors. When a short circuit is applied
to a transformer, there is a significant increase in stray flux, resulting
in greater mechanical forces on the windings, leads, bushings, and
all other current-carrying components. These components, especially
the windings, must be braced to withstand these forces.
A good transformer design must take all of the above effects into account to
minimize the risk of damage and assure a long service life.
5.2 COMPARISONS OF SHORT-CIRCUIT

CURRENTS FOR VARIOUS FAULTS
Since we know (at least approximately) the equivalent circuit of a transformer
by calculating the impedance values from factory tests, it is relatively straight-
forward to calculate the short-circuit currents resulting from various types of
short circuits or faults. There are several types of faults that occur in transmis-
sion and distribution systems, including phase-to-ground faults, phase-to-
phase faults, phase-to-phase-to-ground faults, three-phase grounded faults and
three-phase ungrounded faults. One type of fault is usually more severe than
the others in terms of generating damaging currents. This is called the limiting
fault, because fault current can go no higher for any other fault. The limiting
fault depends on the transformer connection and system impedances and is
not always obvious.
The general short-circuit requirements for liquid-immersed distribution,
power, and regulating transformers are specified in Section 7 of IEEE Std.
C57.12.00-2000 [1, pp. 35–38]. The duration of the short-circuit current that
the transformer must withstand is given by the following formula:
1250
t (5.2.1)
I2

where
t duration of the fault, s
I symmetrical short-circuit current in per unit
For transformers rated above 500 KVA, the standard limits the duration of
the fault to 2 s. The magnitudes of fault currents are calculated according to
the rules given in Table 5.1.
A transformer is required to withstand a first-cycle asymmetrical peak
current, I sc (pk asym), calculated as follows.
I sc (pk asym) K I sc 1.414
(5.5.2)
(1 e ( /2)r/x
sin ) I sc
where
I sc symmetrical fault current, RMS
tan 1 (x/r)
x/r effective ratio of the AC reactance to resistance of the total
impedance that limits the fault current for the transformer
connections used
TABLE 5.1 Accepted Methods for Calculating Fault Currents

by Transformer Category
Category Single-phase KVA Three-phase KVA Fault current calculation
I 5–25 15–75 Transformer impedance

only, limited to 40 per
unit current
I 37.5–110 112.5–300 Transformer impedance
unit current
I 167–500 500 Transformer impedance
unit current
II 501–1667 501–5000 Transformer impedance
only, no fault current
limit
III 1,668–10,000 5001–30,000 Transformer impedance plus
system impedance
IV Above 10,000 Above 30,000 Transformer impedance plus
system impedance

Eq. (5.2.2) accounts for the initial DC offset and its subsequent decay
when the peak of the AC wave occurs. The initial DC offset actually varies,
depending on the precise moment when the circuit is short-circuited. The peak
value is a statistical function; however, the limiting case is when the AC wave
is completely offset initially, as reflected in Eq. (5.2.2). If the x/r ratio is
infinite, the DC offset does not decay, and the first peak is equal to 2 times
the square root of 2 times the RMS value of the symmetrical fault current.
IEEE Std. C57.12.00-2000 also specifies the methods used for short-
circuit testing. Not every transformer that is manufactured is routinely tested
in the factory for short-circuit capability; however, a representative sample of
every generic transformer design is tested to demonstrate the adequacy of the
design.
Example 5.1
A three-winding Grd.Y-Grd.Y- transformer has a T equivalent circuit with
following impedance values:
ZH j0.1821 per unit
ZX j0.02121 per unit
ZY j0.2026 per unit
Calculate the short-circuit currents for each of the following faults at the low-
voltage with the high-voltage winding connected to an infinite bus (a system
with zero impedance):
1. Three-phase ungrounded fault
2. Phase-to-ground fault
3. Phase-to-phase-to-ground fault
4. Phase-to-phase fault
The positive-sequence, negative-sequence, and zero-sequence network con-
nections for the three-phase ungrounded fault are shown in Figure 5.1. In
short-circuit calculations the positive-sequence system voltage source is
usually assumed to be 1.0 per unit with no negative-sequence or zero-
sequence voltage sources. Thus, only the positive-sequence network is in-
volved in a three-phase fault. Note that the series impedance of the transformer
in the positive-sequence network Z HX is simply the sum of Z H and Z X .
The positive-sequence fault current is equal to the voltage divided by
the series impedance: I 1 1.0/j0.1609 j6.215 per unit.
Equations (3.6.4) to (3.6.6) are used to convert the sequence currents
into phase currents:

FIGURE 5.1 Positive, negative, and zero phase sequence networks connected for a
three-phase fault.
IA I0 I 1 I 2 0 j6.215 0 6.215 270°

IB I0 I 1 240° I 2 120° 0 j6.215 240° 0 6.215 150°
IC I0 I 1 120° I 2 240° 0 j6.215 120° 0 6.215 30°
The positive-sequence, negative-sequence, and zero-sequence network
connections for the phase-to-ground fault are shown in Figure 5.2. Since the
system impedance is zero, the high-voltage terminals are short-circuited in the
negative-sequence and zero-sequence networks. In the zero-sequence network
the impedance from H to X is the parallel combination of Z H and Z Y in series
with Z X :
! "
1
1 1
Z HX ZX j0.02121 [ j5.4915 j4.9358] 1
ZH ZY
j0.07469 p.u.
phase-to-ground fault.

The currents at the point of the fault in the positive-sequence, negative-
sequence, and zero-sequence networks are equal:
1.0
I1 I2 I0 j2.5221 per unit
j0.1609 j0.1609 j0.07469
IA I0 I1 I2 j2.5221 j2.5221 j2.5221
7.5663 270°
IB I 0 I 1 240° I 2 120°
j2.5221 j2.5221 240° j2.5221 120° 0
IC I0 I 1 123° I 2 240°
j2.5221 j2.5221 120° j2.5221 240° 0
connections for the phase-to-phase-to-ground fault (B to C to ground) are shown
in Figure 5.3. As in the phase-to-ground fault, the impedance from H to X in
the zero-sequence network is equal to j0.07469 per unit. The total impedance
in series with the positive-sequence voltage source Z S is calculated below.
! "
1
1 1
ZS j0.1609 j0.2119 per unit
j0.1609 j0.07469
The positive-sequence current at the point of the fault is I 1 1.0/Z S
j4.7190 per unit. This current is split into parallel negative-sequence and
phase-to-phase-to-ground fault.

zero-sequence currents at the point of the fault. Taking the current flowing
out of the X terminal as positive current:
1/j0.1609
I2 I1 I1 0.3170
1/j0.1609 1/j0.07469
j1.4961 per unit
I0 I 1 I 2 j3.2229 per unit
IA I0 I 1 I 2 j3.2229 j4.7190 j1.4961 0
IB I0 I 1 240° I 2 120° j3.2229 j4.7190 240° j1.4961 120°
7.2347 138.1°
IC I 0 I 1 120° I 2 240° j3.2229 j4.7190 120° j1.4961 240°
7.2347 41.9°
connections for the phase-to-phase fault (B to C ) are shown in Figure 5.4.
Only the positive-sequence and negative-sequence networks are involved in
a phase-to-phase fault; therefore, I 0 0. The total impedance in series with
the positive-sequence voltage source is the sum of the transformer series im-
pedance values of the positive-sequence and negative-sequence networks:
ZS j0.1609 j0.1609 j0.3218 per unit
1.0
I1 I2 j3.1075 per unit
j0.3218
phase-to-phase fault.

TABLE 5.2 Sequence Currents and Phase Currents for Various Types of Faults
Applied to a Three-Winding Transformer in Example 5.1
Type of fault I1 I2 I0 IA IB IC
Three phase 6.215 0 0 6.215 6.215 6.215

A phase to ground 2.522 2.522 2.522 7.566 0 0
B phase to C phase to ground 4.719 1.496 3.223 0 7.235 7.235
B phase to C phase 3.108 3.108 0 0 5.382 5.382

IA I0 I1 I 2 0 j3.1075 j3.1075 0
IB I0 I1 240° I 2 120° 0 j3.1075 240° j3.1075 120°
5.3823 180°
IC I0 I1 240° I 2 120° 0 j3.1075 120° j3.1075 240°
5.3823 0°
The sequence currents values and the magnitudes of the phase currents
at the low-voltage transformer terminals are tabulated in Table 5.2. (The phase
angles of I 1 , I 2 , and I 0 are equal to 90°.) The limiting fault for this trans-
former is the phase-to-ground fault, because it has the largest magnitude of
fault current 7.566 per unit.
Example 5.2
Assume the transformer in Example 5.1 has a 150 MVA rating, the low-
voltage winding is rated 69 kV, and that all of the transformer impedance
elements have an x/r ratio of 20: 1. Calculate the first cycle asymmetrical peak
fault current for the limiting fault.
Using Eq. (5.2.2),
I sc (pk asym) K I sc
x
tan 1 tan 1 20 1.52 rad
r
sin sin 1.52 0.999
K 1.414 (1 e (1.52 /2)/20
0.999 ) 2.625
The limiting fault in Example 5.1 is a phase-to-ground fault. This fault
has a magnitude of 7.566 per unit.

I sc (pk asym) 2.625 7.566 19.86 per unit
The current base at the low-voltage terminals is calculated below:
KVA base 150,000 KVA
I base 1255 A
1.732 kV base 1.732 69 kV
Converting I sc from per unit to amperes,
I sc (pk asym) 19.86 1255 A 24,926 A
5.3 MECHANICAL FORCES IN

TRANSFORMERS
While the duration of fault current is not normally long enough to cause ther-
mal damage, the damaging effects of mechanical forces become a very impor-
tant design consideration for large power transformers. For a two-winding
transformer carrying normal load current, the current in the primary winding
flows in a direction opposite to the direction of the current in the secondary
winding, and the total ampere-turns in the primary are equal to and opposite
from the total ampere-turns in the secondary. Because there is mutual stray
flux between the windings, the primary and secondary windings tend to repel
each other. The repulsive forces are greatly magnified for the transformer un-
der fault conditions.
The way to approach the analysis of forces on transformer windings is
to consider only the forces on a conductor caused by leakage flux passing
through the conductor. Note that the flux in the core does not exert any force
on the conductor because none of the flux in the core will pass through the
conductor. There is a well-known formula in physics for calculating the force
on a conductor. Sticking to the MKS system of units:
F i B (5.3.1)
where
F force vector on the conductor, N/m
i current vector through the conductor, A
B flux density vector through the conductor, Wb/m2
The three quantities in the formula are vectors and i B is the cross
product of i times B. When applying the cross product, the force vector will
have a component in each of the three directions x, y, and z. The current and
the flux density also have three components. The relationships between the

components of force and components of current and flux density resulting
from the cross product i B are given in the equations below:
Fx iy Bz iz By (5.3.2)
Fy iz Bx ix Bz (5.3.3)
Fz ix By iy Bx (5.3.4)
In Chapter 1, we learned that the magnetic flux density surrounding a

long, straight conductor is directly proportional to the conductor current and
inversely proportional to the distance from the center of the conductor. If two
long parallel conductors carry currents in the same direction, the directions
of the magnetic fields with respect to the currents will produce forces that are
equal and opposite, tending to pull the conductors together. If two long parallel
conductors carry currents in opposite directions, the directions of the magnetic
fields with respect to the currents will produce forces that are equal and oppo-
site, tending to push the conductors apart. This is illustrated in Figure 5.5.
The forces must be equal and opposite because there can be no net force
produced on the pair of conductors; otherwise, there would be a ‘‘levitating
force’’ present. As Figure 5.5 illustrates, the only component of current is in
the z direction (normal to the plane of the page) and the only component
of flux at the centers of each conductor is in the y direction (vertical). There-
fore, the only component of force is in the x direction (horizontal). There-
fore, Eqs. (5.3.3) and (5.3.4) each produces a zero force, and
Fx iz By (5.3.5)
The force in each conductor is equal to the current in that conductor

times the flux density produced by the other conductor. This flux density is
equal to µ o times the current in the other conductor divided by 2 times the
distance r between the conductors.
µo
| Fx | i1 i2 (5.3.6)
2 r
Equation (5.3.6) confirms that the forces on the two conductors must
have equal magnitudes, even if the currents have unequal magnitudes. As
stated earlier, these forces are always in opposite directions; however, the
forces can either be repulsive or attractive, depending on the relative directions
of the currents.

FIGURE 5.5 Forces acting on a pair of straight current-carrying conductors. F1 and
F2 are always equal and opposite.

Example 5.3
Calculate the force between two straight conductors with centers 3 cm apart,
carrying 10,000 A (RMS) in opposite directions. The peaks of the mutual
forces are based on the peak values of the currents, which are 1.414 times the
RMS current values.
4 10 7 N/A
| Fx | (1.414 10,000 A) 2
2 0.03 m
1333 N/m 914 lb/ft
Since the currents are in opposite directions, the mutual forces will be repul-
sive.
5.4 FORCES BETWEEN TRANSFORMER

WINDINGS
Example 5.3 illustrates that tremendous forces exist between one pair of con-
ductors that are spaced fairly close together and carry currents that are compa-
rable to the short-circuit currents encountered in power systems. In transformer
windings, there are many conductors spaced closely together, and when faults
occur the forces acting on these conductors can be truly mind-boggling. With
mutual forces existing between every pair of conductors, calculating all of
these mutual forces on even one conductor is a very formidable task. This
task is complicated by the fact that the geometry of the windings is not even
close to the simple long and straight pairs of conductors. Adding even more
complication is the fact that the leakage flux is distorted by the presence of
the iron core, which also has a complicated geometry, so the most difficult
part is determining the magnitudes and directions of the leakage flux produced
by all these currents.
Calculating short-circuit forces in a transformer using analytical meth-
ods is, in fact, impossible. Some fairly accurate quantitative analysis is possi-
ble with the use of modern computer-aided design tools, such as finite-element
modeling.
Due to the difficulty in computing short-circuit forces accurately, trans-
formers in the early years of transformer technology were built with plenty
of mechanical ‘‘design margin’’ which was determined mostly by trial and
error. In the early 1970s when the first primitive computer-aided design tools
came into existence, many transformer manufacturers attempted to remove

some of the inherent ‘‘fat’’ of the earlier transformer designs in order to gain
an economic advantage over their competitors. Unfortunately, some manufac-
turers cut into the bone as well, and transformers of the 1970s vintage have
a notorious reputation for lacking short-circuit capability. By the end of the
twentieth century, most transformers of that vintage had permanently removed
themselves from service.
Doing any sort of quantitative analysis of short-circuit forces is a task
for the transformer design engineer and is obviously beyond the scope of this
book. But in order to gain at least a fundamental understanding and apprecia-
tion of short-circuit forces without getting bogged down in the complexity of
the math, a qualitative approach can be used instead.
Consider a two-winding core-form transformer. Under short-circuit con-
ditions, the total ampere turns in the primary winding are (approximately)
equal and opposite from the total ampere-turns in the secondary winding. The
magnitudes of the primary and secondary ampere turns are only approximately
equal because of the presence of the magnetizing impedance. This creates a
shunt path that subtracts ampere-turns from one of the windings. Neglecting
this effect, both windings can be modeled as having the same number of turns
and carrying the same current, with the currents located at the magnetic centers
of the coils, as illustrated in Figure 5.6. The three-dimensional figure on the
left-hand side of Figure 5.6 shows the primary and secondary windings as
concentric cylinders with currents flowing in opposite directions along the
magnetic centers. The cutaway view on the right-hand side of Figure 5.6 de-
picts the magnetic forces operating at the magnetic centers. Modeling the
windings as solid composite structures instead of groups of individual conduc-
FIGURE 5.6 A pair of cylindrical concentric windings with their magnetic centers
perfectly aligned.

tors greatly simplifies the problem and aids visualization of the magnetic
forces involved.
The radial forces acting on the primary and secondary coils tend to crush
the inner coil (usually the secondary) toward the center of the core and expand
the outer coil (usually the primary) outward. If the coils have a rectangular
cross-sectional design instead of a circular cross section design, then the outer
coil tends to become circular under short-circuit conditions, thus distorting its
shape. The outward radial forces result in hoop stresses in the conductors. The
tensile strength of the outer conductors is generally one of the major limita-
tions in the short-circuit capability of the outer winding due to these hoop
stresses. The inner winding encounters compressive forces that are dealt with
by bracing the inner winding against the core.
Unless the magnetic centers of the primary and secondary windings are
aligned perfectly, which is rarely the case, the magnetic forces that repel the
windings will have vertical components as well as radial forces. This situation
is illustrated in Figure 5.7.
Since most transformers have tapped primary windings, it is difficult to
align the magnetic centers of the primary and secondary windings for every
tap position. For tap positions other than the full-tap position, a portion of the
primary winding carries no current, creating a ‘‘hole’’ in the winding and
moving the magnetic center away from the hole. One remedy for this is to
bring out the taps in two groups, one group above and the other group below
the center of the winding so that two ‘‘holes’’ are positioned at equal distances
from the center of the winding. This aligns the magnetic center with the geo-
metric center of the winding on every tap position, but this also requires two
FIGURE 5.7 A pair of cylindrical concentric windings with their magnetic centers
offset in the vertical direction, resulting in net vertical forces on the windings.

tap-changing mechanisms per phase. The increased cost of the additional tap-
changing equipment may be offset by other cost savings that result from reduc-
ing short-circuit forces, so there is a design trade-off in this regard.
Each conductor is pulled toward the magnetic center of its own winding
and repelled from the magnetic center of the opposite winding. Because the
conductor has a different proximity to each of the two magnetic centers, there
will be a net vertical force that tends to pull the conductors toward the middle
of the windings.
In a disc-type winding, the conductors are wound in a spiral pattern that
forms a series of flat discs. Such a disc-type winding is shown in Figure 5.8
with the winding discs separated from each other by means of radial spacers
that are aligned in vertical columns. Under short-circuit forces, the discs are
compressed together creating vertical beam stresses on conductors spans be-
tween the spacers. The distances between the radial spacers increase away
from the center of the winding and if these distances are too great, the vertical
FIGURE 5.8 A three-phase core and coil assembly showing the clamping structure
consisting of pressure plates, jack bolts, top and bottom channels, and tie rods.

beam stresses may distort the winding. Therefore, the number of radial spacers
is another critical design feature.
In order to control the vertical short-circuit forces, disc windings in core
form transformers are kept under tremendous compressive forces by means
of various coil clamping systems. The compressive clamping forces keep the
windings stationary and under compression at all times in order to prevent
damage from distortion. One such coil clamping system for a three-legged
core form transformer is depicted in Figure 5.8.
Referring to Figure 5.8, each set of windings on each core leg is com-
pressed between two thick pressure plates, shown as the cross-hatched compo-
nents in the figure. The pressure plates are made of a strong material that also
has good electrical insulating properties. Specially treated laminated wood or
epoxy-based materials are suitable for these pressure plates. In the design
shown in Figure 5.8, the pressure plates bear against top and bottom C chan-
nels that are connected by eight tie rods. Rings of jack bolts press down on
the top pressure plates, compressing the windings and tending to force the top
and bottom C channels apart. The eight tie rods restrain the forces between
the top and bottom C channels. The total force applied through the jack bolts
and restrained by the tie rods is greater than the maximum net vertical short-
circuit forces that are calculated (or estimated) on the windings.
In a shell-form transformer, radial forces tend to compress the pancake
coils toward their magnetic centers instead of exploding the coils outward,
unlike the high-voltage coil in a typical core-form transformer. Compression
forces are usually easier to deal with than tensile forces, which gives the shell-
form transformer a distinct advantage over the core-form design. Since the
high-voltage coils are normally sandwiched between the low-voltage coils in
a shell-form transformer, the axial forces tend to compress the high-voltage
pancake coils toward the center of the winding pack and force the low-voltage
pancake coils away from the center of the winding pack. The axial forces are
restrained by fill material that is wedged between the coils, between the wind-
ing packs, and between the low-voltage coils on the outer winding packs and
the transformer tank, which provides mechanical bracing. The resulting con-
figuration, shown in Figure 5.9, is an assembly that is securely braced in all
directions and has great mechanical short-circuit strength.
The fill material is shown in Figure 5.9 by the cross-hatched areas. These
filled areas are not actually solid, but contain numerous ducts for cooling oil
to flow. The transformer tank is divided into an upper and lower half. Wedges
at the end surfaces of the windings compress the entire coil structure as the
upper tank is lowered on top of the lower tank, resulting in a structure that
resists all movement.

FIGURE 5.9 A three-phase shell-form transformer cutaway sketch. The pancake coil
packs are compressed between the ends of the transformer tank, forming a solid bulk.
5.5 SHORT-CIRCUIT FORCES IN THREE-

WINDING TRANSFORMERS
The addition of a tertiary winding complicates the already complicated calcu-
lation of short-circuit forces because the ampere-turns of the three windings
are not necessarily equal. Depending on the type of fault, the currents in the
primary, secondary, and tertiary windings can be different in both magnitude
and direction. Consider the case of a Y-Grd.Y- transformer with a phase-
to-ground fault applied to the secondary winding. Since the primary winding
is ungrounded, all of the zero-sequence current flows in the tertiary winding
as a closed circulating current. This condition is illustrated as a vector diagram

FIGURE 5.10 A phase-to-ground fault applied to the secondary of a three-winding
transformer. Each arrow represents 1 unit of ampere-turns.
It is assumed that the total ampere-turns is approximately zero in all

cases. Each current arrow in Figure 5.10 represents one ‘‘unit’’ of ampere-
turns for the phase-to-ground fault applied to the secondary winding. Knowing
the actual numbers of turns or the actual currents in each of the windings is
not important in this analysis. In the A phase leg of the transformer, the pri-
mary winding has 2 units, the secondary winding has 3 units, and the
tertiary winding has 1 unit. In the B phase and C phase legs, the primary
windings have 1 unit each, the secondary windings have 0 units, and the
tertiary windings have 1 unit each.
Assume that the physical three-winding transformer has a core-form de-
sign with the windings ordered from the center of the core as follows: tertiary,
secondary, and primary. The ampere-turns for a phase-to-ground fault applied
to the secondary are illustrated in Figure 5.11.
The primary (outer), secondary (middle), and tertiary (inner) windings
and their magnetic centers are shown schematically in Figure 5.11. Each sym-
bol ‘‘•’’ represents one unit of ampere-turns flowing out of the page and each
symbol ‘‘ ’’ represents one unit of ampere-turns flowing into the page. The
directions of the net radial forces can be ascertained from the directions of
the ampere-turns as shown. These forces tend to expand the primary winding
outward and collapse the secondary and tertiary windings inward toward the
center of the core. From the simple illustration in Figure 5.11, it would appear
that the radial forces between the three pairs of windings partially cancel each
other out. Thus, the radial forces in a three-winding transformer on the faulted
phase are in general somewhat smaller than the radial forces on the faulted
phase in a two-winding transformer.

FIGURE 5.11 Distribution of ampere-turns in a three-winding transformer with a
phase-to-ground fault applied to the secondary.
5.6 EXCITING CURRENT INRUSH

When a transformer is initially energized, there is a phenomenon known as
exciting current inrush. Although inrush currents are not generally as damag-
ing as fault currents, the duration of exciting current inrush is on the order of
seconds (as compared to on the order of cycles with fault currents). Exciting
current inrush conditions also occur much more frequently than short circuits,
so this phenomenon is worth exploring.
Consider what happens when initially energizing a single-phase trans-
former. From Chapter 1 we learned that the flux in the core is equal to the
integral of the excitation voltage. If the circuit is closed when the voltage is
passing through zero and the initial flux is zero, the sinusoidal flux will be
fully offset from zero. The full-offset flux has a peak value that is twice the
peak value of a symmetrical sinusoidal flux. In other words, the peak flux for
a fully offset wave can approach two times the normal peak flux, and this is
generally sufficient to drive the core into saturation. At this point, the only
thing that limits exciting current is the air-core impedance of the winding,
which is several orders of magnitude smaller than the normal magnetizing
impedance.
Therefore, the exciting current is much greater than the normal exciting
current during the half cycle when the core is saturated. During the opposite
half cycle, the core is no longer saturated and the exciting current is approxi-
mately equal to the normal exciting current. This is illustrated in Figure 5.12.

FIGURE 5.12 Exciting inrush current for a core having no residual flux.

The situation is even more extreme when there is residual flux in the
core and the direction of the residual flux is in the same direction as the offset
in the sinusoidal flux wave. This is illustrated in Figure 5.13. Note that Figure
5.12 and 5.13 are drawn on current different scales, so the peak current plotted
in Figure 5.13 is actually much larger than the peak current plotted in Figure
5.12.
To find the peak inrush current, limited only by the air-core reactance,
it is convenient to calculate the inductance of the winding using cgs units:
0.4 N 2 A mt
L (5.6.1)
l
FIGURE 5.13 Exciting inrush current for a core having a residual flux.

where
N number of turns in the coil
A mt area inside the mean diameter of the coil, cm 2
l axial length of the coil, cm
L inductance of the coil, µH
The flux generated by the inductance L is equal to the residual flux plus 2
times the normal flux change minus the saturation flux, since the saturation
flux is in the iron. But L is related to the inductance and the current:
N L
L (5.6.2)
I
Therefore, the peak inrush current is expressed in the cgs system of units as
follows [2]:
( r 2 n s)l 10 8
I peak (5.6.3)
0.4 NA mt
where I peak is in amps and
r residual flux
n normal flux change
s saturation flux
Without resistance in the circuit, each successive peak would have
the same value and the current inrush would go on indefinitely. With resis-
tance in the circuit, however, there is a significant voltage drop across
the resistance and the flux does not have to rise quite as high as the pre-
vious cycle. The integral of the voltage drop represents a net decrease in
the flux required to support the applied voltage. Since the i R voltage drop
is always in the same direction, each cycle decreases the amount of flux
required. When the peak value of flux falls below the saturation value of the
core, the inrush current disappears. The rate of decay is not exponential al-
though it resembles an exponentially decaying current. For large power trans-
formers, the inrush current can persist for several seconds before it finally dies
off.
The line reactance has the effect of reducing the peak inrush current by
simply adding inductance to the air-core inductance of the winding. There is
a definite relationship between inrush current and short-circuit current because
both are related to the air-core inductance of the windings. (Remember that
short circuits tend to exclude flux from the core.) Typically, a rule of thumb

is that peak inrush currents are a little over 90% of peak short-circuit currents.
The magnetic forces caused by inrush currents are generally much smaller
than short-circuit forces, however. Because only one winding per phase is
involved, there is no magnetic repulsion between windings.
The whole problem of analyzing exciting current inrush gets much more
difficult when 3-phase transformers are involved. This is because the phase
angles of the exciting voltages are 120° apart, there are interactions of currents
and voltages between phases, and the three poles of the switching device do
not close at exactly the same time. Nevertheless, it is safe to say that the peak
magnitude of inrush current for three-phase transformers approaches the short-
circuit current levels.
One of the interesting features of exciting current inrush is that since
the current is fully offset, there are large percentages of even harmonics pres-
ent. Even harmonics are otherwise rarely encountered in power circuits. There
is also a phenomenon known as sympathetic inrush, where a transformer that
is previously energized will exhibit a sudden change in current when a nearby
transformer is switched on. Sympathetic inrush is caused by changes in line
voltages from the inrush currents of the second transformer.
5.7 TANK OVERHEATING FROM

ZERO-SEQUENCE CURRENTS
In Chapter 2, several differences between three-legged and five-legged core-
form transformers were identified. In particular, there is no magnetic return
path for zero-sequence flux in three-legged core-form transformers and if the
core is excited by zero-sequence voltages, zero-sequence flux is produced that
must return through the air, or through the air to the transformer tank. Since
the reluctance of the air gap is large, the zero-sequence reactance is small,
typically around 0.4 per unit of the transformer impedance base. If zero-
sequence flux returns through the walls of transformer tank, there will be a
net flux surrounded by the inner surface of the tank. This net flux induces a
current induced in the tank wall in a direction opposite from the net ampere-
turns in the transformer windings. This is illustrated in Figure 5.14.
In effect, the tank is a -connected single-turn tertiary wound on each
core leg. Since there is only one turn, the currents induced in it can be many
times the zero-sequence currents in the actual transformer windings. Unfortu-
nately the transformer tank is not designed to carry very much current and if
the zero-sequence flux becomes too large, the induced currents in the tank can
cause severe overheating in matter of seconds. In some cases, the temperatures
get high enough to blister the paint on the tank.

FIGURE 5.14 Tank currents in a 3-legged core form transformer excited with a zero-
sequence current.
One common way for this condition to occur is with an open primary
phase to a Grd.Y-Grd.Y transformer when a load connected to the secondary.
This can easily happen in distribution systems where fuses are commonly
used. The sequence network connections for an open A phase primary trans-
former connection is shown in Figure 5.15.
FIGURE 5.15 Positive, negative, and zero phase sequence networks connected for
an open primary phase to a three-legged core form transformer carrying load.

In Figure 5.15, Z T0 is the magnetizing branch impedance of the zero-
sequence equivalent circuit for the transformer. Z T0 is much smaller than the
ordinary magnetizing impedance because of the high-reluctance path for zero-
sequence flux in the three-legged core form design. I T0 is the zero-sequence
magnetizing branch current. Note that I T0 would still exist even if there were
no transformer tank present; however, the major portion of I T0 is represented
by the current circulating in the tank.
Z T0 is typically around 30% of the transformer impedance base. The load
impedances, Z L1 , Z L2 and Z L0 , should all be at least 100% of the transformer
impedance base to prevent overloading the transformer. The series transformer
impedances Z 1 , Z 2 , and Z H0 Z X0 , are typically less than 10% of the trans-
former impedance base. With all of the above information and assuming that
the load has a 90% power factor and the transformer impedances are purely
reactive, I T0 is about 0.56 per unit for the circuit above. Since most of I T0 is
tank circulating current, a typical value for tank currents under the conditions
described above is about 50% of the transformer rating.
Example 5.4
A three-legged core form transformer is connected Grd.Y-Grd.Y with a 1 per
unit load applied. One of the of the primary fuses blows open. Assume that
the tank circulating current is 50% of the transformer rating, which is a fairly
typical value. Calculate the tank circulating current in amperes for the follow-
ing transformer characteristics.
KVA rating: 1500 KVA

Voltage rating: 12470Y/7200-208Y/120
Number of secondary turns: 10
Calculate the base current on the secondary side of the transformer:
(1,500,000 VA/3)
I base 4167 A per phase
120 V
Since the transformer tank is equivalent to a -connected tertiary surrounding

each core leg by a single turn, the turns ratio between the secondary and the
tank is 10 :1. Calculating the tank current,
I tank 4167 A per phase 10 41,670 A
This example illustrates the magnitude of damaging currents that can occur
for a Grd.Y-Grd.Y core-form transformer with a blown primary fuse. It is for

this reason that this transformer design must be avoided when the possibility
of an open primary phase exists.
5.8 PRIMARY FUSE MISOPERATIONS

We saw in Section 5.7 that tank overheating can easily result from a blown
primary fuse. One of the drawbacks of protecting transformers with fuses is
that they operate independently and somewhat randomly, which can result in
some very serious consequences. Take, for example, a -Grd.Y connected dis-
tribution substation transformer protected by primary fuses. For any phase-to-
ground fault, there will be fault current through two of the primary fuses. If
only one of the primary fuses blows, then the transformer will go into single-
phase operation with two of the secondary phase voltages at normal voltage
(but 180° apart in phase angle) and zero secondary voltage on the faulted phase.
For single-phase loads, this is not a problem (except for loads connected to
the faulted phase) but three-phase motors will not operate properly at these
voltages and can easily be damaged. The situation can be analyzed using the
method of symmetrical components; however, this requires applying two dif-
ferent faults simultaneously: an open-circuit fault at the primary plus a phase-
to-ground fault at the secondary. It is more easily illustrated by the vector
diagrams shown in Figure 5.16. If either the A phase primary fuse or the B phase
primary fuse blows with a phase-to-ground fault sustained at the secondary, the
voltage the A phase secondary winding is zero. This causes the voltage across
primary winding between the A and C phases to collapse, resulting in the col-
lapsed shown in the vector diagrams on the right-hand side of Figure 5.16.
If the phase-to-ground fault clears, then the secondary voltage on one
phase is normal and the secondary voltages of the other two phases will have
one-half of the normal voltage, as illustrated by the vector diagram shown in
Figure 5.17 for the case for a blown A phase primary fuse. The A phase voltage
at the primary will be the average of the B phase voltage and the C phase
voltage, collapsing the as shown on the right-hand side of Figure 5.17. It
is clear that only one-half of the normal voltages appear across the A-B primary
winding and the A-C primary winding, and only one-half of the normal volt-
ages appear across the A phase and B phase secondary windings. Any single-
phase motors that are supplied by these phases will operate at half voltage,
which will certainly cause motor damage if this conditions persists.
An even more serious situation can occur when a phase-to-phase second-
ary fault occurs on a -Grd.Y connected transformer protected by primary
fuses. There will be fault current in all three primary fuses; however, one of
these fuses will have twice the fault current of the other two, and usually this

FIGURE 5.16 Vector diagrams of a phase-to-ground fault at the secondary of a -
Y transformer with one blown primary fuse. (a) Fault currents before fuse blows; (b)
voltages after fuse blows.
fuse will blow first. This results in single-phase operation with normal second-
ary voltage on one phase and one-half normal secondary voltages on the other
two phases.
On occasion, however, one of the other primary fuses will blow. If this
happens, there will be normal secondary voltages on two of the phases and
double the normal secondary voltage on one phase. Figure 5.18 shows this
condition for a B-to-C phase secondary fault, which normally results in a
blown B phase primary fuse. In this case, however, the A phase primary fuse
blows instead.
Since B and C phase are shorted together on the secondary side of the
transformer, the phase-to-neutral voltages are equal and so the A-B phase pri-
mary voltage must equal the B-C phase primary voltage. Since the B phase and
C phase fuses are intact, the voltage across the B-C phase primary winding is
the normal voltage. This forces the A phase voltage to be ‘‘outside the delta’’

FIGURE 5.17 Vector diagrams of a phase-to-ground fault at the secondary of a -
Y transformer with one blown primary fuse after the fault clears. (a) Fault currents
before fuse blows; (b) voltages after A phase blows, fault clears.
so the A-B voltage can be equal to, and in phase with, the B-C voltage. Since
the B-C primary voltage is normal, the A-C primary voltage, which is equal to
the sum of the A-B and B-C primary voltages, will be 2 times the normal voltage.
The A-C primary voltage is induced across the A phase secondary winding as
2 times the normal secondary voltage. Consequently, the transformer operates
in a single-phase mode with two of the secondary phases at normal voltage
levels and the other secondary phase at 2 times the normal voltage level.
This is obviously a dangerous situation that can cause extensive equip-
ment damage as well as bodily injury and possibly death to utility customers
who are exposed to electric appliances operating at twice their normal volt-
ages. In reality, a doubling of voltage is not quite achieved because the trans-
former core will saturate and thus limit the magnitude of the over voltage.
Nevertheless, this type of fuse misoperation does occasionally occur, and the
resulting equipment damage is usually quite extensive.

FIGURE 5.18 Vector diagrams of an A phase to C phase fault at the secondary of
a -Y transformer with the A phase fuse blown. (a) Fault currents before fuse blows;
(b) voltages after A phase fuse blows.
5.9 FERRORESONANCE
Ferroresonance occurs when line capacitance resonates with the magnetizing
reactance of a core while it goes in and out of saturation. Ferroresonance is
usually associated with potential transformers, which are instrument trans-
formers that are used to develop voltages used by relays; however, it can also
occur with power transformers under special circumstances.
Ferroresonance is another occurrence that can cause equipment damage;
fortunately, it is preventable by simply avoiding certain types of transformer

connections with the types of circumstances that enable it to occur. Because
these connections are routinely avoided in practice, ferroresonance is not en-
countered very often and there isn’t much information about it in the literature.
Ferroresonance is worthy of mention, however, because it can utterly destroy
a transformer.
The necessary conditions for ferroresonance are established in the
system shown in Figure 5.19. In the example shown in Figure 5.19, the -
connected tertiary winding of a large three-winding substation transformer
FIGURE 5.19 A situation where ferroresonance may occur. The cable capacitances
form three parallel L-C elements that are in series with each other and the source
voltages.

supplies a distribution type station-service transformer with a Grd.-Y primary
winding. The supply lines to the station-service transformers are through a set
of shielded cables. If the cable runs are fairly long, a significant amount of
phase-to-ground capacitance may exist.
When a transformer core operates near saturation, the B-H curve is
highly nonlinear, and the effective permeability of the core can take on a range
of values that vary with the changes in flux density. Each of the inductances
shown as L1, L2, and L3, will have instantaneous inductance values that are
proportional to the effective permeability of the core at any given instant in
time. These inductances form parallel L-C circuits that are in series with one
another and in series with the source voltage. Since L1, L2, and L3 are con-
stantly varying along with the effective permeability of the core, it is almost
certain that a series resonant condition will exist at least part of the time during
every cycle.
When a series resonance exists, even for a brief period, this causes very
large voltages across the L-C elements. These voltages are capable of destroy-
ing the transformer and any other equipment connected to it. The nonlinear
nature of this problem makes mathematical analysis virtually impossible, but
the phenomenon has been observed both in the field and experimentally, and
the voltages have been measured and recorded.
In the example above, the conditions for ferroresonance can be disrupted
by the simple expedient of -connected secondary winding to the station ser-
vice transformer. The -connected winding assures that the vector sum of the
voltages of all three phases add to zero, stabilizing the neutral point of the Y-
connected primary winding and preventing excessive voltage across the wind-
ings. The presence of a -connected secondary winding will essentially ‘‘snuff
out’’ ferroresonance in this circuit.
5.10 VOLTAGE SURGES

The effects of lightning and switching surges on a transformer are similar.
The two properties that both of types of voltage surge have in common are:
(1) a voltage peak that may be significantly greater than the normal line volt-
age, and (2) a rate of change of the voltage that is much faster than the rate
of change of the normal line voltage. In fact, the rate of change alone can
have more damaging effects on the turn-to-turn insulation of a winding than
the magnitude of the peak voltage alone.
To study the effects of voltage surges, it is necessary to understand wave
propagation through a transformer winding. A transformer winding is usually
a coiled conductor with a series inductance between each turn and the turn

FIGURE 5.20 High-frequency model of a transformer winding. The inductance and
capacitance elements form a waveguide that propagates voltage and current waves.
above and below it. Since the turns are coiled in close proximity with each
other, there is also a shunt capacitance between each turn and the one above
and below it. This forms a series of parallel L-C circuits from one end of the
winding to the other, with each parallel L-C circuit representing one turn.
Since each turn is also capacitively coupled to ground, the winding takes
on a structure similar to a waveguide, as illustrated in Figure 5.20, with a
large number of parallel L-C elements in series and a large number of shunt
capacitances to ground. Let
L inductance per turn, H
C turn-to-turn capacitance per turn, F
C capacitance to ground per turn, F
The high-frequency characteristics of the waveguide structure can be analyzed
using Laplace transforms. For high-frequency phenomena, it is customary to
ignore the transformer core, since the winding currents are highly localized.
The core only comes into play at low frequencies where the winding currents
are global.
In Laplace notation, the impedance of each L-C element is represented
by Z(s), where s is the Laplace operator corresponding to the / t operation.
The admittance of each of the shunt elements C is represented by Y(s).
sL
Z(s) (5.10.1)
1 s 2 LC
Y(s) sC (5.10.2)
When many of these elements are connected together, the resulting
structure has a characteristic admittance Y 0 (s) and a propagation constant

(s). In this case, unlike an ideal waveguide, the propagation ‘‘constant’’ is
not really constant, but varies with frequency. Above a certain frequency c
called the cutoff frequency, the propagation constant becomes an attenuation
factor and frequency components above c will not propagate and decay expo-
nentially instead.
! "
1/2
Y(s)
Y 0 (s) S (5.10.3)
Z(s)
(s) [Y(s)Z(s)] 1/2 (5.10.4)
c (LC ) 1/2
rad/s (5.10.5)
Suppose a voltage surge is applied across the entire winding. This case
occurs when a lightning surge arrives at the high-voltage terminals of a wind-
ing connected Grd.-Y. The voltage surge at the winding terminal is a time
function e 0 (t) having a Laplace transform e 0 (s). The current at the winding
terminal i 0 (t) also has a Laplace transform i 0 (s).
i 0 (s) e 0 (s)Y 0 (s) (5.10.6)
Note that the current coming out of the winding at the grounded end is
not the same as the current going into the winding at the line end because the
voltage surge is a wave that must travel down the entire length of the winding
before emerging at the grounded end. As the current wave passes through the
winding, it is delayed by the propagation constant, so the current i x (s) at turn
number x is related to the current at the line terminal by the following expres-
sion:
i x (s) e 0 (s)Y 0 (s)e (s)x

(5.10.7)
The turn-to-turn voltage e x (s) at turn number x is equal to the current i x (s) at
turn number x times the impedance of the L-C element Z(s):
e x (s) e 0 (s)Y 0 (s)Z(s)e (s)x

(5.10.8)
but
! "
1/2
Y(s)
Y 0 (s)Z(s) Z(s) [Y(s)Z(s)] 1/2 (s) (5.10.9)
Z(s)
Therefore Eq. (5.10.8) reduces to the following expression:
e x (s) e 0 (s) (s)e (s)x

(5.10.10)

The turn-to-turn voltage expressed as a time function e x (t) is solved by
the inverse Laplace transform:
j
e x (t)
2
j
# j
e x (s)e st ds (5.10.11)
Equation (5.10.11) is not very difficult to solve numerically by computer. It

is only necessary to numerically integrate the expression over a frequency
range slightly greater than the cutoff frequency c . The numerical integration
is successfully carried out using a summation technique over the frequency
range 2 c 2 c using the following parameters: ds j0.01 c and
s j . The value of should be slightly positive. A value of 0.1 c
usually produces good results. This summation technique requires about 400
iterations for each value of e x (t) solved. Using complex variables this is a very
easy task for a computer to perform.
The remaining task is to define the voltage surge and calculate its La-
place transform. A typical lightning surge is modeled as the so-called 1.2/50
µs full wave. This wave goes from zero to peak voltage in 1.2 µs and decays
to 50% of peak value in 50 µs. The 1.2/50 µs full wave has the following
time function:
e 0 (t) 8.333 10 5 tu(t) 8.4358
(5.10.12)
10 tu(t
5
1.2 10 6)
where u(t) is the unit step function at t 0.
The Laplace transform of e 0 (t) is
(8.333 8.4358e s 1.2 10 6
) 10 5
e 0 (s) (5.10.13)
s2
Plugging these functions into a computer algorithm that solves the inverse
Laplace transform through a summing technique produces a plot of the turn-
to-turn voltage as a function of time and as a function of the turn number x.
The computer-generated plot shown in Figure 5.21 is for a 1.2/50 µs lightning
wave propagating along a winding with L 1.0 10 5 H per turn, C
1.0 10 F per turn, and C
9
1.0 10 F-turn. The turn-to-turn voltages
9
are shown at x 1 and at x 20 turns into the winding. Note that the turn-
to-turn voltage is over 10% of the peak voltage that is applied across the entire
winding.
A chopped wave also has a 1.2 µs wavefront, but the voltage then sud-
denly drops to zero as soon as the surge reaches peak voltage. The chopped
wave simulates the effects of lightning arrestors that spark over and cause a

FIGURE 5.21 Computer simulation of the turn-to-turn voltages at the first turn and
the twentieth turn in response to a full wave applied across the winding terminals.
Note that the higher-frequency components above the cutoff frequency have been atten-
uated at the twentieth turn.
voltage collapse. The chopped wave can cause much more severe turn-to-turn
voltages than the full wave because of the rapid change in voltage. The effects
of the sudden voltage change are limited to some extent by the cutoff fre-
quency c which prevents the voltage from instantaneously changing. A com-
puter simulation of the chopped wave voltages for the same winding used
in the full-wave simulation (not shown here) results in turn-to-turn voltages
approaching 50% of the peak voltage applied across the entire winding.
These extreme theoretical turn-to-turn voltages dissipate fairly rapidly
as the wave moves along the winding; hence, the end turns of the winding
usually show far more stress than the middle turns. If a transformer is designed
to withstand a 750 kV chopped wave, the end turns would have to be able to
withstand a turn-to-turn voltage of 375 kV!
Lightning-induced failures are typically manifested by turn-to-turn fail-
ures at or near the end turns of the windings. For a grounded winding, we

would expect lightning-induced failures to occur most often occur at the line
end, and they usually do; but some lightning-induced failures occur at the
grounded end. This is explained by the fact that a traveling wave is reflected
at the grounded end of the winding. The reflected line-to-ground voltage wave
cancels the forward line-to-ground voltage wave, but the forward and reflected
current waves add together and double the current at the grounded end. Since
the turn-to-turn voltage is equal to the current times the impedance of the L-
C elements, the turn-to-turn voltage also doubles at the point of reflection.
Surge arrestors, also called lightning arrestors, are connected between
the transformer terminals and ground to limit the peak surge voltage. Arrestors
are coordinated with nominal system voltages so they will not spark over at
normal line voltages. Basic impulse insulation level (BIL) ratings are based
on the surge voltages that are expected to occur when arrestors are properly
applied. Table 5.3 shows standard BIL ratings of power transformers for vari-
TABLE 5.3 Full Wave and Chopped Wave Test Voltages by BIL Class
Full wave Chopped wave Nominal system

BIL (kV) test (kV) test (kV) voltage (kV)
110 110 120 15

150 150 165 25
200 200 220 34.5
250 250 275 46–69
350 350 385 69–115
450 450 495 115–138
550 550 605 115–161
650 650 715 138–230
750 750 825 161–230
825 825 905 230
900 900 990 230–345
1050 1050 1155 345
1130 1130 1430 500
1175 1175 1290 345
1425 1425 1570 500
1550 1550 1705 500
1675 1675 1845 500
1800 1800 1980 765
1925 1925 2120 765
2050 2050 2255 765
Source: Ref. 1, p. 16.

ous nominal system voltages, and the voltage levels applied for the full-wave
test and the chopped-wave test [1].
Example 5.5
A 150 MVA transformer has a 16% nameplate impedance with an X/R ratio
of 10 :1. The transformer is connected to a system impedance of 10% on a
100 MVA base with an X/R ratio of 5:1. What is the peak asymmetrical fault
current in per unit for a three-phase fault on the load side of the transformer?
Converting the system impedance into the transformer base:
0.10 150 MVA
Z 0.15 per unit
100 MVA
R2 X2 0.15 2 0.0225 per unit
Rearranging,
$%
2
X 0.0225
1
R R2
Solving for the left-hand side of the equation,
$%
2
X
1 1 52 26
R
Substituting for 1 (X/R) 2 :

0.0225
26
R2
Solving for R,
0.0225
R2 0.0008654 per unit
26
R 0.0294 per unit
Solving for X,
X (R 2 X 2) R 2
(0.0225 0.0008654) 1/2 0.147 per unit
For the transformer:
(R 2 X 2) 0.16 2 0.0256 per unit

Rearranging,
$%
2
X 0.0256
1 1 10 2 101
R R2
Solving for the left-hand side of the equation,
$%
2
X
1 1 10 2 101
R
Substituting for the left-hand side of the equation,

0.0256
101
R2
Solving for R,
0.0256
R2 0.0002535 per unit
101
R 0.0159 per unit
Solving for X,
X (R 2 X 2) R 2
X (0.0256 0.0002535) 1/2 0.159 per unit
Combining system and transformer impedances,
Total R 0.0294 0.0159 0.0453 per unit
Total X 0.147 0.159 0.306 per unit
Total Z (0.0453 2 0.306 2) 1/2 0.309 per unit
Calculating the total X/R ratio,
X 0.306
6.755
R 0.0453
X
tan 1
1.424 rad
R
Applying Eq. (5.2.2),
1 e sin 1.424
(1.424 /2)/6.755
I peak (asym) 1.414
0.309
7.482 per unit on a 150 MVA base

Example 5.6
A 50 MVA single-phase shell-form transformer has a voltage rating of 79,670
to 39,840 V with an 8% nameplate impedance. The secondary winding is split
into two pancake coils in series, each having 400 turns with the primary pan-
cake coil sandwiched between the two secondary coils. The centers of the
secondary windings are 10 cm from the center of the primary winding. A short
circuit is applied to the secondary winding with the primary connected to a
1 per unit voltage source with zero impedance. Estimate the axial force on
each of the coils. Assume that the magnetic centers of the coils are aligned
perfectly in the radial direction and the magnetic centers each have an effective
length of 3 m (see Figure 5.22).
Calculate the secondary short-circuit current:
50,000,000 VA/39,840 V
If 15,688 A
0.08
Secondary ampere-turns 15,688 A 400 turns 6,275,100 ampere-turns,
which are split into 2 halves. The primary ampere-turns 6,275,100 ampere-
turns.
The magnetic centers of the two secondary coils and the primary coil
are 3 m long and are 0.1 m apart. All of the ampere-turns are concentrated
at the magnetic centers as single turns, as shown in Figure 5.23. The forces
on the primary coil cancel. The force on each secondary coil are calculated
in MKS units:
6,275,100 1 3,137,550/0.1 3,137,550 3,137,550/0.2) 3 µ0
F N
2
5.906 10 6 N ( 1.328 10 6 lbf in English units)
FIGURE 5.22 Pancake winding used in Example 5.6.

FIGURE 5.23 Location of the magnetic centers for Example 5.6.
Example 5.7
A -connected tertiary winding of a large substation transformer supplies a
Grd.Y- station service transformer through a set of cables, as shown in Figure
5.24. The A phase cable sustains a phase-to-ground fault.
There are two possible fusing arrangements:
1. A set of fuses at the tertiary winding of the large substation trans-
former
2. A set of fuses at the primary of the station service transformer
Determine the phase-to-ground voltages at the station service transformer for
both of the above fusing arrangements if the A phase fuse blows and the cable
fault is sustained. Which of the fusing arrangements is preferable?
Arrangement A:
12,470 12,470
E AN 0 E CN 6235 V E BN 6235 V
2 2
FIGURE 5.24 Circuit diagram for Example 5.7.

Arrangement B:
E CN E CA 12,470 V 210° E BN E BA 12,470V 150°
Due to the secondary of the station service transformer, the sum of the
voltages around the must equal zero:
E AN E BN E CN 0
E AN 12,470 V 150° 12,470 V 210° 21,599 V 0°
The rated phase-to-neutral voltage is 7200 V and the transformer is severely
overvoltaged with arrangement B. Therefore, arrangement A is preferred.
REFERENCES
1. IEEE Std. C57.12.00-2000. IEEE Standard General Requirements for Liquid-
Immersed Distribution, Power, and Regulating Transformers. New York: Institute
of Electrical and Electronics Engineers, Inc., New York 2000.
2. R. L. Bean, N. Chakan, Jr., H. R. Moore and E. C. Wentz. Transformers for the
Electric Power Industry. McGraw-Hill Book, New York, 1959.

6
Ancillary Equipment
Transformers are equipped with an array of ancillary equipment in order to

survive and function in the field. This chapter describes how this equipment
is designed, how it functions, and how it should be maintained. The proper
design and maintenance of ancillary equipment is just as important as the
proper design and maintenance of the transformer itself and can present its
own set of problems, since unlike the transformer proper, ancillary equipment
may contain moving parts that are subject to wear. Many transformer failures
have been the result of carelessness with regard to ancillary equipment.
6.1 BUSHINGS
A transformer designed for outdoor use has its core and coils completely en-
closed by a steel enclosure. In order to connect the windings to the electrical
system, the leads are brought out of the tank through bushings. Since the leads
are energized at line voltages, the bushings must insulate and isolate the leads
from each other and from the tank. A cutaway view of a high-voltage oil-
filled condenser bushing is shown in Figure 6.1.
A condenser bushing gets its name from the grading capacitor (aka con-
denser) that relieves the electrical stresses internal to the bushing. Core insula-

FIGURE 6.1 Cutaway sketch of a condenser bushing, shown on its side. (This bush-
ing is normally mounted in the vertical position.)
tion, consisting of oil-impregnated kraft paper, and the conducting plates of

the grading capacitor surround a hollow tube operating at line potential that
runs through the middle of the bushing. A mounting flange that is at ground
potential is bolted to the transformer tank with a ground sleeve extending
below the flange. A skirted porcelain insulator is placed between the grounded
mounting flange and the energized upper portion of the bushing. A shorter
porcelain insulator is placed between the ground sleeve and the energized
bottom portion of the bushing. An upper reservoir, with a sight glass or float oil
level gauge, supplies insulating oil for impregnating the kraft paper insulation
below. A capacitance tap is electrically connected to one of the plates of the
grading capacitor for measuring the power factor of the insulation when the
bushing is tested. This tap is normally grounded when the bushing is in opera-
tion.
In the configuration shown in the diagram, the hollow tube conducts
current through the bushing with the transformer winding lead attached bolted
to the bottom of the bushing through a connector. In a different configuration,
called a draw lead bushing, the lead from the transformer winding is drawn
through the hollow tube and terminates at the top of the bushing using a special
type of top connector with inside threads that mate with the draw lead connec-
tor. The draw lead configuration generally has a lower ampere rating than the
bottom-connector configuration because the draw lead conductor is usually
smaller in cross-sectional area than the hollow tube. Also, there is an additional

temperature gradient since I 2 R losses from the draw lead must be transferred
through the space between it and the inner surface of the hollow tube.
Skirts are used on the outer surfaces of the upper and lower insulators
to lengthen the creepage paths between the energized ends of the bushing and
the ground sleeve. Since porcelain is naturally a porous material, the outer
surfaces of the upper and lower insulators are coated with a hard glaze to
shed moisture and contamination. The oil level inside the transformer must
be maintained above the bottom of the ground sleeve to assure that the lower
porcelain insulator is immersed in oil. This allows the creepage path along
the surface of the lower insulator in oil to be significantly shorter than the
creepage path for the upper insulator in air.
EHV (extra high voltage) bushings have corona rings attached to the
top of the bushing to prevent corona from the high voltage stresses at sharp
edges and corners. Corona rings are generally used at voltages above 230 kV.
Porcelain is strong in compression and structurally weak in tension.
Therefore, in order for a long bushing to withstand cantilever forces, the porce-
lain is compressed by means of massive springs in the top assembly that keeps
the hollow tube in tension. Also, since it is impractical to fabricate the porce-
lain of a large bushing as a single assembly, large pieces are usually assembled
as smaller sections that are interlocked and kept in compression.
Condenser bushings are also used for low-voltage bushing applications;
however, bulk-type bushings are generally used for 15 kV and below. Bulk-
type bushings consist of a porcelain insulator, a center conductor, and a mount-
ing flange. There is no oil reservoir, and no grading capacitor. In some bulk-
type bushing designs, the core insulation is made of kraft paper that is in
communication with the transformer oil with wicking action to keep the paper
oil-impregnated. In other bulk type bushing designs, all of the insulating mate-
rial is made out of porcelain, which greatly simplifies the design. An example
of a low-voltage bulk-type bushing design is shown in Figure 6.2. A solid
conductor extends from the top and bottom connector through the center of
the bushing. The insulation consists of a hollow porcelain tube with skirts on
the upper portion only. The mounding flange and ground plane surrounds the
middle of the porcelain insulator. Because the bushing operates at a low volt-
age, there is sufficient creepage path below the flange so the bushing can be
operated safely without regard to a minimum oil level.
Bushings have voltage ratings, BIL ratings, and current ratings. Since
bushings have no inherent overload capability, transformer loading is kept
within the bushing ampere ratings and the bushings are generally sized some-
what larger than the nominal load in order to accommodate the transformer
overload capability.

FIGURE 6.2 Cutaway sketch of a solid bushing, suitable for side-wall mounting.
The internal connections are made to the four-hole pad on the right and the external
leads are made to the threaded stud on the left.
Transformer bushings come in a bewildering array of shapes and sizes.

For a long time, there was no effort on the part of transformer manufacturers
to standardize bushings so that they could be interchanged among transformers
of the same voltage classes and similar KVA ratings. Even when similar trans-
formers were built by the same manufacturer, the bushings often would not
be compatible with each other. To add yet more confusion, bushings supplied
by the same manufacturer that were identical often carried different catalog
numbers. The result was that each transformer had a set of bushings that was
unique to that particular unit, and the transformer owners had to stock a large
number of spare bushings to cover those in service.
Some utility companies instituted computer databases, entering the criti-
cal dimensions and other parameters for every in-service and spare bushing,
so that matches could be found among bushings that were ‘‘close enough’’
in size and capacity. In recent years, there has been an effort to standardize
bushings and for manufacturers to use standardized bushings in their trans-
formers. As older transformers are culled from the population, bushing inter-
changeability should become much less of an issue in the future.
6.2 OIL PRESERVATION SYSTEMS

Transformer oil provides insulation as well as cooling for the core and coil
assembly. Oil contamination is a serious problem because it robs the oil of
its dielectric properties and renders it useless as an insulating medium. There-

FIGURE 6.3 Sealed-tank oil preservation system.
fore, one of the most important design features of a transformer is the oil
preservation system.
The simplest method of oil preservation is the sealed-tank design, as
shown in Figure 6.3. The core and coils are immersed in oil with an air or
gas blanket above the oil surface. The volume of the gas blanket must be
sufficient to allow hot oil to expand inside the tank without over pressurizing
the tank. Under extremes in temperature, the sealed-tank design may prove
impractical because of the large gas volume that is required. A large volume
of gas is generated during electrical faults. A pressure relief valve is provided
to allow fault gases to escape In order to keep the tank from rupturing. The
main advantages of the sealed-tank design is its inherent simplicity and low
maintenance requirements. For these reasons, sealed-tank transformers are
common with distribution transformers because they are seldom maintained.
One of the earliest alternative methods of oil preservation was the con-
servator tank design. In conservator-type transformers, the main tank is com-
pletely filled with oil with a smaller oil reservoir (conservator tank) mounted
above the tank and connected to it by a pipe called a ‘‘gooseneck,’’ as shown
in Figure 6.4. The conservator tank is vented to the atmosphere at the top and
the normal oil level is approximately in the middle of the conservator to allow
for expansion and contraction. The purpose of the gooseneck is to break up
the convection flow of hot oil from the transformer tank and the cooler oil in

FIGURE 6.4 Conservator oil preservation system.
the conservator tank. This is only partially successful, however, so there is

always some communication between the transformer oil bathing the core and
coils and the oil in the conservator tank that is exposed to the atmosphere.
The oil in the transformer tank is under a slight positive pressure equal to
the head of oil above it. Although the conservator tank design prevents over
pressurization when the oil expands, it is only marginally effective in keeping
the oil free of contaminants from the atmosphere. One variation uses a desic-
cant canister in the breathing vent to absorb moisture, which keeps the atmo-
sphere inside the conservator tank dry. The desiccant canister requires replen-
ishment at intervals. A color change from pink to blue indicates when the
desiccant needs to be replaced.
A variant of the conservator tank design places an expandable bladder
between the oil and the outside air. This design has been fairly successful over
the years, although the bladder can be damaged or torn.
Another oil preservation system that is a variation of the conservator is
called the gas oil seal design, as depicted in Figure 6.5. A gas oil seal system
has a relatively small gas blanket of inert nitrogen over the oil in the main
transformer tank. Dissolved oxygen in the oil leads to a chemical reaction

FIGURE 6.5 Gas-oil-seal oil preservation system.
known as oxidation. The byproducts of oxidation include H 2 O, acids and

sludge, all of which will shorten the life of the transformer, along with various
hydrocarbon compounds. Using a blanket of inert nitrogen over oil that has
been degassed will considerably reduce dissolved oxygen and oxidation by-
products.
The gas space over the core and coils is connected to the gas space of a
lower sealed oil reservoir. The oil in the bottom of the lower reservoir communi-
cates with oil in the bottom of an upper reservoir. A blanket of air, which com-
municates with the atmosphere, covers the oil in the upper reservoir. A head
of oil h exists between the oil levels in the upper and lower reservoirs. A positive
pressure in the lower reservoir must maintain this head of oil, and hence there
must be a positive pressure in the main transformer tank as well.
As the oil in the main tank expands thermally, the increased pressure
of the nitrogen blanket forces oil out of the bottom of the lower reservoir into
the bottom of the upper reservoir. This increases the head of oil h balancing
the increased pressure. The oil in the lower reservoir ‘‘seals’’ the nitrogen
blanket in the main transformer, hence the name, and keeps the oil in the main
tank free from contamination. In some systems, a dehydrating breather, filled
with desiccant, further minimizes moisture intrusion into the oil. The main
disadvantage of this system is that if there are any gas leaks in the main tank,
the positive pressure cannot be maintained and the oil in the upper reservoir
drains into the lower reservoir, collapsing the head of oil.
One other major oil preservation system has been called by various
brand names, e.g., Inertair supplied by Westinghouse Electric. This system,
depicted in Figure 6.6, uses a pressurized nitrogen bottle with a pressure

FIGURE 6.6 Inertaire oil preservation system.
regulator/breather that maintain a nearly constant positive pressure in a nitro-

gen blanket over the oil in the main tank. The main advantage of the regulated
pressure design is that it is almost impervious to oil contamination and will
perform its function even if there are small gas leaks. The disadvantage is that
the nitrogen bottle requires periodic replacement, so maintaining the system
is somewhat expensive. The nitrogen bottle will require frequent replacement
if there is excessive temperature cycling or if there are significant gas leaks.
6.3 COOLING EQUIPMENT

Heat from core losses and copper losses must be dissipated to the environment.
In dry type transformers, cooling is accomplished simply by circulating air
around and through the coil and core assembly, either by natural convection
or by forced air flow from fans. This cooling method is usually limited to
low-voltage indoor transformers (5 kV and below) having a three-phase rating
below 1500 KVA. At higher voltages, oil is required to insulate the windings,
which prevents the use of air for cooling the core and coils directly. At higher
KVA ratings, the losses are just too high for direct air cooling to be effective.
In outdoor environments, direct air cooling would introduce unacceptable
amounts of dirt and moisture into the windings.
Transformers come in various cooling classes, as defined by the industry
standards. In recent years, there have been attempts to align the designa-
tions that apply to transformers manufactured in North America with the IEC
cooling-class designations. Table 6.1 [1] gives the IEC designations and the
earlier designations that are used in this book. All of the IEC designations use
four letters. In some respects, the IEC designations are more descriptive than
the North American designations because IEC makes a distinction between
forced-oil/air cooled (OFAF) and directed-flow-air cooled (ODAF). Some

TABLE 6.1 Designations and Descriptions of the Cooling Classes Used
in Power Transformers
Previous
designation IEC designation Description
OA ONAN Oil-air cooled (self-cooled)

FA ONAF Forced-air cooled
OA/FA/FA ONAN/ONAF/ONAF Oil-air cooled (self-cooled), followed by
two stages of forced-air cooling
(fans)
OA/FA/FOA ONAN/ONAF/OFAF Oil-air cooled (self-cooled), followed by
one stage of forced-air cooling (fans),
followed by 1 stage of forced oil (oil
pumps)
OA/FOA ONAN/ODAF Oil-air cooled (self-cooled), followed by
one stage of directed oil flow pumps
(with fans)
OA/FOA/FOA ONAN/ODAF/ODAF Oil-air cooled (self-cooled), followed by
two stages of directed oil flow pumps
(with fans)
FOA OFAF Forced oil/air cooled (with fans) rating
only—no self-cooled rating
FOW OFWF Forced oil/water cooled rating only (oil/
water heat exchanger with oil and wa-
ter pumps)—no self-cooled rating
FOA ODAF Forced oil/air cooled rating only with di-
rected oil flow pumps and fans—no
self-cooled rating
FOW ODWF Forced oil/water cooled rating only (oil/
water heat exchanger with directed
oil flow pumps and water pumps)—
no self-cooled rating
Source: Ref. 1.
people find using the four-letter designations somewhat awkward, and this
book uses the earlier designations throughout.
In small oil-filled distribution transformers, the surface of the tank is
sufficient for transferring heat from the oil to the air. Ribs are added to the
tanks of some distribution transformers to increase the surface area of the tank
and to improve heat transfer. Large distribution transformers and small power
transformers generally require radiator banks to provide cooling. Regardless
of whether the tank surface, ribs, or radiators are used, transformers that trans-

fer heat from oil to air through natural convection are all cooling class OA
transformers.
Radiators used on OA transformers generally have round cooling tubes
or flat fins with large cross section areas in order to allow oil to flow by natural
convection with minimal resistance. Hot oil from the core and coils rises to
the top of the tank above the inlet to the radiator. Cool oil from the radiator
sinks to the bottom of the radiator through the outlet and into the bottom of
the core and coils. This process is called thermo-siphoning and the oil velocity
is relatively slow throughout the transformer and radiators. For this reason,
OA transformers have relatively large temperature gradients between the bot-
tom oil and the top oil, and relatively large temperature gradients between the
winding temperatures and the top oil temperature. Likewise, the air circulates
through the radiator through natural convection, or is aided by the wind.
As the transformer losses increase, the number and size of the radiators
that are required to cool the oil must increase. Eventually, a point is reached
where wind and natural convection are not adequate to remove the heat and
air must be forced through the radiators by motor-driven fans. Transformers
that have forced air cooling are cooling class FA transformers. FA transform-
ers require auxiliary power to run the fan motors, however, and one of the
advantages of OA transformers is that they require no auxiliary power for
cooling equipment. Since additional cooling is not usually needed until the
transformer is heavily loaded, the fans on most FA transformers are turned
off until temperatures exceed some threshold value, so under light load the
transformer is cooled by natural convection only. These transformers are cool-
ing class OA/FA transformers.
Some transformers are cooled by natural convection below temperature
T 1, turn on one stage of fans at a higher temperature T 2 and turn on a second
stage of fans at an even higher temperature T 3 . These transformers are cooling
class OA/FA/FA transformers. The direction of air flow in forced-air units is
either horizontally outward or vertically upward. The vertical flow pattern has
the advantage of being in the same direction as the natural air convection, so
the two air flows will reinforce each other.
Although the cooling capacity is greatly increased by the use of forced
air, increasing the loading to take advantage of the increased capacity will
increase the temperature gradients within the transformer. A point is reached
where the internal temperature gradients limit the ability to increase load any
further. The solution is to increase the oil velocity by pumping oil as well as
forcing air through the radiators. The usual pump placement is at the bottom
of the radiators, forcing oil from the radiator outlets into the bottom of he
transformer tank in the same direction as natural circulation but at a much
higher velocity. Such transformers are cooling class FOA transformers. By

directing the flow of oil within the transformer windings, greater cooling effi-
ciency can be achieved. In recognition of this fact, the calculation of hot-spot
temperatures is modified slightly for directed-flow cooling class transformers.
As in forced-air designs, forced-oil cooling can be combined with OA
cooling (OA/FOA) or in two stages (OA/FOA/FOA). A transformer having
a stage of fans and a stage of oil pumps that are switched on at different
temperatures would be a cooling class OA/FA/FOA transformer.
The radiator design on FOA transformers can differ substantially with
the radiator design on FA transformers. Since the oil is pumped under consid-
erable pressure, the resistance to oil flow is of secondary importance so the
radiator tubes can be designed to maximize surface area at the expense of
cross section area. FOA radiators are sometimes called coolers instead, and
tend to resemble automotive radiators with very narrow spaces between the
cooling tubes and flat fins in the spaces between the cooling tubes to provide
additional surface area. The comparison of the two types is illustrated in Fig-
ures 6.7 (OA/FA type) and 6.8 (FOA type).
FIGURE 6.7 OA/FA radiator construction. The large radiator tubes minimize restric-
tion of oil flow under natural convection. The fan is shown mounted at the bottom
with air flow directed upward.

FIGURE 6.8 FOA cooler construction. The oil is forced through narrow tubes
from top to bottom by means of oil pumps. The cooling fans direct air horizontally
outward.
Cooling equipment requires maintenance in order to run efficiently

and provide for a long transformer life. There is the obvious need to main-
tain the fans, pumps, and electrical supply equipment. The oil coolers them-
selves must be kept clean as well, especially FOA-type coolers. Many
transformers have overheated under moderate loads because the cooling fins
were clogged with insect and bird nests, dust, pollen, and other debris. For
generator step-up transformers, where the load is nearly at nameplate rating
continuously, steam-cleaning the coolers once every year is a good mainte-
nance practice.

6.4 TEMPERATURE, OIL LEVEL,
AND PRESSURE GAUGES
Temperature controls are required in order to turn on and off the cooling equip-
ment. These controls are usually combined with a visible dial-type gauge that
measures ‘‘winding temperature.’’ This is really a misnomer because the
gauge does not actually contact the winding. Instead, it measures the top oil
temperature plus a temperature gradient produced by a small heater sur-
rounding the thermometer bulb. This heater is connected to a current trans-
former on one of the phases of the secondary leads, so as the secondary load
increases, so does the current through the heater resistance. The heater then
becomes a mimic of the actual transformer winding with the winding tempera-
ture gauge measuring a temperature that is roughly equivalent to the true wind-
ing temperature.
In addition to (or instead of) the winding temperature gauge, most trans-
formers have an oil temperature gauge that measures the actual top oil temper-
ature. The difference in temperature between the winding temperature gauge
and the top oil temperature gauge is one indication of how heavily the trans-
former is loaded. Winding and/or top oil temperatures should be routinely
observed to see whether the transformer is operating within normal tempera-
ture limits. There have been many cases where an abnormal temperature indi-
cation has uncovered serious problems with transformers.
One example of this was a case of an OA cooling class transformer
operating with a very high oil temperature. Further investigation revealed that
a leak in the radiator had caused the oil level to drop below the radiator inlet,
resulting in a virtual total loss of cooling. In other cases, investigations of
elevated transformer temperatures have revealed blocked coolers and malfunc-
tioning cooler controls.
An oil level gauge is required so that the correct oil level can be main-
tained. There is usually a mark on the gauge that indicates the 25°C level,
which is the proper oil level at that temperature. Maintaining the proper oil
level is extremely important because if the oil level falls below the level of
the radiator inlet, flow through the radiator will cease and the transformer
will overheat. A very low oil level can expose energized and current-carrying
components that are designed to operate in oil and could result in overheating
or an electrical flashover. If the oil level is too high, it could cause over pressur-
ization when the oil expands.
If the transformer is equipped with a constant-pressure nitrogen oil pres-
ervation system, then pressure gauges are included to measure the pressure
of the gas blanket and the nitrogen in the make-up bottle.

Transformers that have a gas blanket over the oil in the main tank usually
come equipped with pressure gauges. On random inspections, a sealed-tank
unit should have a slight positive or a slight negative pressure. If the pressure
gauge consistently records zero pressure under all loading and temperature
conditions, this is an indication that the transformer tank has a leak, allowing
it to ‘‘breathe.’’ This condition must be taken seriously and fixed, because a
transformer that breathes is probably contaminated with moisture.
6.5 TAP-CHANGING EQUIPMENT

A transformer’s rated voltage may not match the system voltage exactly, or
it may be necessary to raise or lower the output voltage to supply a certain
load. In these cases, a portion of a winding can be removed or added to change
the transformer turns ratio. The simplest tap-changing device operates on a
‘‘break before make’’ principle and changes taps on the primary winding.
Obviously, such a device cannot be operated when the transformer is carrying
load or even when the transformer is energized because it would break load
current and/or magnetizing current otherwise. This device is called a tap
changer for deenergized operation. Years ago, it was called a no-load tap
changer, but this description has fallen out of favor because the name implies
that it can be operated when the transformer is energized but not carrying
load, which is not the case. Most tap changers for deenergized operation have
a total of five tap positions. There are usually two tap positions above the
nominal voltage rating and two tap positions below the nominal voltage plus
a tap at the nominal voltage. The voltage increments between taps are gener-
ally 21/2% of the nominal voltage, so the full tap range is 5%.
A rotary drum-type tap changer and the winding connections are shown
in Figure 6.9. An insulated rotating shaft aligns a spring-loaded shorting wedge
between pairs of hollow cylindrical electrodes. The winding taps are connected
to the cylindrical electrodes by soldering or brazing. Different manufacturers
have used other rotary tap changer configurations and mechanisms with linear
movement are available. The tap changers for deenergized operation are usu-
ally mounted above the core and coil assembly to make inspection and mainte-
nance possible. The taps are changed by a wheel on the outside of the trans-
former that locks in each tap position with indicating markers to show what
tap the transformer is on. In three-phase transformers, the tap changers of all
three phases are mechanically ganged together so that all three phases are
always on the same taps.
If the tap changer is in the primary winding, then the primary current
increases with respect to the load current on the lower taps, increasing the

FIGURE 6.9 A tap changer for deenergized operation (break before make). There
are five tap positions, with the connections for full winding taps shown.
primary winding current with respect to the load current. The fact that part
of the winding resistance is removed from the circuit on the lower taps partially
compensates for the increased current; however, the lowest tap still has the
highest total I 2 R losses for a given load current. The winding taps are always
in the middle portion of the winding to keep the magnetic center aligned with
the other windings as sections of the winding are removed from the circuit
by changing taps. Since the winding is never quite balanced on two of the
five taps, the winding can be split into three sections, as shown in Figure 6.10.
This arrangement requires two tap-changing mechanisms per phase, but the

FIGURE 6.10 A tapped winding with two sets of taps that balance the ampere-turns
around the geometric center of the winding. This configuration minimizes the vertical
forces when the transformer is subjected to short circuits.
magnetic center of the winding is always aligned at the number 6 tap to help
control short-circuit forces.
Tap changers for deenergized operation are designed to be moved infre-
quently. The tap settings are generally specified for the particular location on
the electrical system and the settings do not change unless system conditions
permanently change. Because a good electrical contact often depends on con-
tact ‘‘wiping,’’ it is generally a good idea to operate the tap changer periodi-
cally (when the transformer is out of service) to wipe the contacts clean. The
contacts themselves are generally silver- or tin-coated since bare copper has
a tendency to develop a copper sulfate film under oil which increases the
contact resistance. This can lead to a thermal runaway effect from oil coking.
As the temperature around the contacts increases, the oil around the contacts
can coke or turn into carbon. This forms a carbon film that can actually force
the contacts apart so the load current must pass through a layer of high-
resistance carbon. This increases the temperature still further, leading to more
coking and so forth until the contacts overheat and are destroyed.
After a tap changer is operated, it is important that the tap position is
verified by a transformer turns ratio (TTR) test. The details of the TTR test
will be covered in Chapter 8. There have been numerous cases where the tap
changers of one or more phases were not correctly aligned even when the
external markings indicated that they were. Energizing a transformer with tap
changer contacts parted will result in immediate failure when the winding
current arcs across the gap.
6.6 LOAD TAP CHANGERS

When load levels and/or system voltages change frequently, it is sometimes
necessary to adjust the transformer tap ratio to follow the changes in system

conditions. It is obviously impractical to do this while the transformer is deen-
ergized or unloaded, so a special type of tap changer has been developed to
change taps under full-load conditions.
Whereas the tap changer for deenergized operation is a break-before-
make switching device, a load tap changer (LTC) must be a make-before-break
switching device, requiring bridging over two adjacent taps before moving on
to the next tap. If an electrical short circuit were placed between two taps,
then the short-circuit current would be extremely large based on the large
number of ampere turns with few turns. Therefore, an impedance must be
inserted between the taps in order to limit the short-circuit current that flowing
in the bridging position.
Transformer manufactures in North America adopted the preventative
autotransformer method as the solution to this problem. This scheme is de-
picted Figure 6.11, showing the bridged position. Note that the tapped winding
is not magnetically coupled with the preventative autotransformer. The pre-
ventative autotransformer has a 1:1 turns ratio and with the tap changer in
the bridged position and the ampere-turns in each half of the preventative
autotransformer must cancel each other. Therefore, the load current flows vir-
tually unimpeded through both halves of the autotransformer winding. Any
circulating current that flows in the closed loop between the taps encounters
the magnetizing impedance of the preventative autotransformer, which effec-
tively blocks the circulating current. The voltage at the output of the preventa-
tive autotransformer is the average of the voltages of the bridged taps.
FIGURE 6.11 A load tap changer (LTC) in the bridging position with load currents
evenly divided between the movable contacts.

FIGURE 6.12 A load tap changer (LTC) in the full tap position.
The tap changer in the unbridged, full-tap position is illustrated in Figure

6.12. With the tap changer in this configuration, all of the load current is
coming from a single tap through both moving contacts and the output voltage
is equal to the voltage at that tap. Again, the ampere-turns in the two halves of
the 1: 1 preventative autotransformer cancel, so the load current flows virtually
unimpeded.
When the tap changer begins to move to the next tap position, the upper
moving contact must part while the lower moving contact remains on the tap.
All of the load current in the upper moving contact is then suddenly transferred
to the lower moving contact, as shown in Figure 6.13. Since all of the load
current now flows through one-half of the autotransformer winding, it encoun-
ters the magnetizing impedance of the autotransformer, which would normally
create a large voltage drop. This problem is remedied by designing the preven-
tative autotransformer with a relatively low magnetizing impedance by build-
ing in air gaps in the core and by allowing the core to saturate at a relatively
low winding voltage. The saturation voltage should be slightly higher than
the voltage between taps in order to prevent circulating current in the bridged
position yet low enough not to introduce an excessive voltage drop at the load
terminals.
During the load transfers between moving contacts, there is considerable
arcing due to the very large series inductance in the tapped winding and the
windings of the preventative autotransformer. It is therefore necessary to per-
form a load transfer through a set of stationary arcing contacts in order to

FIGURE 6.13 A load tap changer (LTC) beginning to move to the bridging position.
prevent burning and pitting of the moving contacts when breaking load cur-
rent. One of the many schemes for performing the load transfer is illustrated
in Figure 6.14.
When both moving contacts are on the same tap, all of the arcing con-
tacts are closed. Before the upper moving contact moves, the upper transfer
contact opens. Since the middle arcing contact and the lower transfer contact
FIGURE 6.14 A load tap changer (LTC) beginning to move to the bridging position
showing the load current through a single set of transfer contacts.

are closed, the upper transfer contact is merely breaking a parallel current, so
minimal arcing occurs there. Next, the middle arcing contact opens, inter-
rupting the load current through the upper moving contact in series with the
transformer winding inductances. This produces a substantial amount of arcing
and the middle arcing contacts must be designed to withstand this duty. Fi-
nally, with the upper moving contact isolated, it can move on to the next tap
position. When the upper moving contact is established on the next tap, all
of the arcing and transfer contacts are closed to establish the bridging position.
The movement of the lower moving contact can proceed in a similar manner,
first by opening the lower transfer contact, then the middle arcing contact, and
finally the lower moving contact. Notice that this scheme requires only one
set of arcing contacts for both sets of moving contacts.
The main advantage of the preventative autotransformer scheme is that
the tap changer can stay on the bridging position indefinitely. Thus, bridging
positions can be utilized the same as fixed taps, reducing the number of physi-
cal taps required to provide the required number of voltage changes. The main
disadvantage of this method is that a separate set of core and coils must be
provided for the preventative autotransformer. In a three-phase transformer
with load tap changers, one three-phase preventative autotransformer is used
instead of three separated preventative autotransformers for economy. Since
the KVA transformed is relatively small, the preventative autotransformer can
usually be accommodated within a fairly small space inside the main tank.
LTCs are generally installed on the secondary side of the transformer.
LTCs require periodic maintenance. The motor-driven mechanism needs
to be cleaned and lubricated and the controls inspected and tested. The main
moving contacts should be periodically inspected and replaced if worn or pit-
ted. The arcing contacts are the components that have the greatest duty and
require the most frequent overhaul. If the arcing contacts operate in oil, the
oil must be changed periodically because of the build up of carbon and other
byproducts that are produced by the frequent arcing that takes place.
European transformer manufacturers adopted the resistance-type load
tap changer. By the turn of the twenty-first century, the resistance-type load
tap changer became the worldwide standard mainly because large power trans-
formers, where LTCs are commonly installed, are no longer built in the United
States. One resistance-type load tap changer design is illustrated in Figure
6.15. The transfer switch is open only when the tap changer is in the bridged
position, as shown in the figure, with the resistor limiting the circulating cur-
rent that flows between the taps. Unfortunately, the resistor is also in the load
current path, so I 2 R heating in the resistor is of concern. Unlike the preventa-
tive autotransformer which splits the output voltage between the moving con-
tacts in the bridged position, the output voltage of a resistance-type load tap

FIGURE 6.15 A resistance-type load tap changer (LTC) momentarily in the bridging
position. The resistor restrains short-circuit currents between adjacent taps.
changer is always equal to the voltage of the upper moving contact. Since
there are no half-step output voltages available in the bridging positions, there
is no advantage in leaving the tap changer in this position. Therefore, the tap
changer stays in the bridging position only long enough to let the second
moving contact to meet up with the first, thus limiting the I 2 R heating in the
resistor. Two sets of arcing contacts are required, one for each moving contact.
The single transfer switch breaks only the parallel current with both sets of
arcing contacts closed, so there is minimal arcing across the transfer switch.
The complete resistance-type tap-changing mechanism, complete with
moving contacts, arcing contacts, transfer switch, and resistor can be housed
in a single unit that can be easily replaced in the field. This is one of the major
advantages of this type of load tap changer. The tap-changing unit is usually
located in the main transformer tank with the parts insulated by the same
transformer oil that bathes the core and coils, with the exception of the arcing
contacts which are in a sealed self-contained oil compartment to prevent con-
taminating the main transformer with arcing products. Resistance-type load
tap changers have a very long life and can perform hundreds of thousands of
operations between overhauls.
6.7 VOLTAGE REGULATING TRANSFORMERS

There is a special type of transformer that is designed specifically to regulate
line voltage over a relatively narrow output range, typically around 10%
of the incoming voltage. Regulating transformers are technically not power

transformers, and many of the industry standards treat the two as different
types of transformer. Since the voltage ratio is close to 1.0, it makes sense
to use an autotransformer connection and voltage regulators indeed almost
exclusively use the autotransformer connection. The series winding is fully
tapped end-to-end and it can be connected in the buck as well as the boost
mode. In the neutral tap position (neither boost nor buck), the series winding
is completely disconnected and the regulator does not transform any energy
through its windings. A load tap changer is used to change taps of the series
winding and a reversing switch is provided to convert the regulator from the
buck to boost.
Since the voltage ratio is so close to unity, the multiplication factor F c
of most regulators is quite high and their physical sizes are small compared
to the power throughput that they can handle. Of course, since the voltage
ratio is close to unity, the effects of short circuits and line surges, which are
exaggerated in autotransformers, are even more acute with voltage regulators.
Three-phase voltage regulators are used in substations to regulate the
voltages of feeder circuits. Single-phase and three-phase pole-mounted voltage
regulators are found in distribution circuits, along lines where voltage sag is
a problem.
Maintenance of voltage regulators follows the same guidelines as LTC
maintenance. The mechanical drive, controls, main contacts, and arcing con-
tacts all require attention.
6.8 TAP CHANGER AUTOMATIC CONTROLS

The tap-changing mechanism is usually motor-driven and can be controlled
manually and automatically. In the automatic mode, the output voltage of the
transformer is compared to a reference voltage and a raise/lower signal is sent
to the tap changer motor when the output voltage falls outside a specified
band, called a dead band. The dead band must not be smaller than the voltage
between taps; otherwise, it will ‘‘hunt’’ endlessly and burn up the tap changer.
The dead band must not be too wide, however, because the purpose of voltage
regulation will be defeated. Ordinarily, the dead band is set to a voltage be-
tween two and three tap increments. With the tap voltage typically around 1%
of the nominal secondary voltage, this provides regulation within a 2–3%
range.
If two or more transformers with load tap changers are connected in
parallel, then it is important that all transformers operate at the same trans-
former turns ratio; otherwise, excessive circulating KVAR results. The way
this is implemented is to have the tap changer on one of the parallel transform-

ers control voltage as the lead tap changer, with the other tap changers as the
followers. Circuitry is installed on the followers to sense the direction of reac-
tive power flow through each transformer. If too much reactive power is flow-
ing from the primary to the secondary, then its secondary taps are lowered.
If too much reactive power is flowing from the secondary to the primary, then
secondary taps are raised. Appropriate dead bands are established to prevent
the LTCs from hunting and to limit interactions among the tap changer con-
trols.
One such control scheme, called a load-balancing method, is depicted
in Figure 6.16 for three transformers with voltage regulators supplying a com-
mon load bus. If the three transformer impedances equal and if the transform-
FIGURE 6.16 A load-balancing control scheme for three parallel transformers with
load tap changers.

ers are set on the proper tap positions, the transformer secondary currents will
all be in phase with the load current and there will be no current unbalance.
If one or more transformer is set on the wrong tap, circulating currents will
flow in all three transformers. The principle of operation of the load-balancing
method is to separate each of the transformer secondary currents into a load-
current component and a circulating-current component. The transformer sec-
ondary currents flow through current transformers, labeled CT 1, CT 2, and
CT 3 in Figure 6.16. The currents at the CT secondaries split into two paths
at each of the CT secondary windings.
Path 1 (to the right) goes through a set of auxiliary transformers, labeled
CT 4, CT 5, and CT 6. The secondaries of the auxiliary CTs are connected
in series, forcing the currents in all three primary windings equal one another,
each being one-third of the total load current. By default, the unbalance-current
components must flow in path 2 to the left.
Each of the circulating-current components (also called unbalanced-
current components) flows through an inductive reactance element, called a
paralleling reactor. The paralleling reactors are labeled jX in Figure 6.16. In
general, the unbalance-current components of the three transformers are un-
equal. The voltages developed across the paralleling reactors are added to the
sensed voltages at the secondary windings of the main transformers, which
are used to control the movement of the tap changers.
If transformer 1 is on a higher tap position than transformer 2 or trans-
former 3, the unbalanced currents flowing through the parallel reactors in-
crease the sensed voltage at transformer 1 and reduce the sensed voltages at
transformers 2 and 3. This causes transformer 1 to lower its taps and transform-
ers 2 and 3 to raise their taps. If transformer 1 is on a lower tap position than
transformers 2 and 3, the unbalanced currents flowing through the parallel
reactors decrease the sensed voltage at transformer 1 and increase the sensed
voltages at transformers 2 and 3. This causes transformer 1 to raise its taps
and transformers 2 and 3 to lower their taps.
6.9 VARIABLE PHASE SHIFTING

TRANSFORMERS
If two areas are connected with a number of transmission paths, it is sometimes
necessary to control the flow of real power through the transmission network.
Phase-shifting transformers are installed to force a phase angle shift between
the ends of a transmission line and create a real power flow. A phase shift of
a few degrees is all that’s required to move massive amounts of power around
the system, so a phase-shifting transformer only needs to transform a tiny

fraction of the power that is moving through the system. The power flow
between two buses can be approximated by the following equation.
VS VR sin
P (6.9.1)
X
where
P real power flow in per unit
VS per unit voltage of the sending bus
VR per unit voltage of the receiving bus (assumed to lag V S)
phase angle difference between V S and V R
X per unit reactance between the sending and receiving bus
The situation is analogous to a voltage-regulating transformer, which
can create a flow of reactive power by a slight change in voltages. Again, an
autotransformer is the logical choice, using the special phase-shifting connec-
tion shown in Figure 6.17. The common tapped series windings are equivalent
FIGURE 6.17 The winding configuration of a variable phase-shifting transformer

used to control real power flow. Note that the voltages of the sending terminals and
receiving terminals have equal magnitudes.

to the common and tapped series windings in a voltage-regulating transformer,
except they are interconnected differently to produce a phase angle shift in-
stead of a voltage change. There are six load tap changers in this configuration
although some designs use three load tap changers plus a reversing switch
instead.
The voltages at the sending terminals (S1-S2-S3) are shown lagging the
voltages at the receiving terminals (R1-R2-R3), but since each tap changer
can travel the full range of taps, the phase shift can also be reversed with the
sending terminals leading the receiving terminals. Note that the magnitudes
of the line-to-line voltages at the sending and receiving terminals are equal
to each other. Therefore, the change in voltage is a pure phase shift.
If reactive power flow needs to be regulated with real power flow regu-
lated independently, voltage and phase angle control can be combined within
a single regulating transformer with two sets of tap changers operating inde-
pendently. One set of tap changers regulates the in-phase voltages and the
other set of tap changers regulates the quadrature-phase voltages, which are
combined at the output. A typical phase shifting transformers may be capable
of a variable phase angle shift up to 20°; however, if X is on the order of a
few percent, a fairly small phase angle shift may be sufficient for diverting
large blocks of power.
Example 6.1
Suppose a phase-shifting transformer, such as the one in Figure 6.17, is con-
nected to a 500 kV system. The phase shifter regulates 1000 MW of power
from the receiving terminals to the sending terminals by shifting the phase
angle of the sending terminals by 3°. How much MVA is actually trans-
formed by the phase shifter under these conditions?
From the voltage vectors of the sending and receiving voltages, the volt-
ages across the tapped windings E T and the voltages across the common wind-
ings E C are calculated:
500,000 V 3°
ET 2 sin 15,113 V
1.732 2
500,000 V 117°
EC 2 sin 492,272 V
1.732 2
Let I T current flowing in the tapped windings and I C current flowing in
the common windings.
15,113
IC IT 0.0307 IC
492,272

The current out of S1 based on 1000 MW of flow:
1,000,000,000 W 1155 A
|I S1 |
1.732 500,000 V phase
From the vector diagram of the transformer, the currents in all windings
flow in a circular loop, but the phase angles of the currents in the tapped
windings and the two adjacent common windings are 120° apart. The current
flowing out of terminal S1 are the sum of the winding currents at terminal
S1:
|I S1 | |I T 0° I C 120° | I T | 1 0° 0.0307 120°|

1155 A
1.016 IT
phase
Solving for I T :
1155 A
IT 1137 A
1.016
The MVA transformed is equal to the winding currents times the winding
voltages:
15,113 V 1,137 A
MVA 17.2 MVA per phase
1,000,000
3 17.7 MVA per phase 51.6 MVA total
The total transformed MVA slightly greater than 5% of the total MVA
flowing through the phase shifter. Like a voltage regulator, the core and coils
of the phase shifter can be surprisingly small for the huge amount of power
flow it is able to regulate.
Example 6.2
Two identical transformers, each having a j0.15 per unit impedance, supply
a substation load. Their load tap changer controls are operating in a load-
balancing scheme. Transformer 1 is set on the 1.05 per unit secondary load
tap, and transformer 2 is set on the 1.00 per unit secondary load tap position,
with unity voltages assumed at the primaries of both transformers. The load
may be represented as a constant impedance of 1.0 20° per unit. The parallel-
ing reactors each have a 1.0 impedance.

FIGURE 6.18 Circuit diagrams for Example 6.2.
1. Find the voltage at the load and the currents at the secondaries of
the two transformers and sketch these quantities as vectors.
2. Decompose each of the secondary currents into a load-current com-
ponent and an unbalanced-current component.
3. Find the voltages developed across the paralleling reactors and
sketch these voltages along with the load voltage.
The circuit is shown along with its equivalent circuit in Figure 6.18.
The load impedance is converted into rectangular form:
1.0 20° 0.94 j0.342 per unit
The loop equations are as follows:
Ia j0.30 Ib j0.15 1.05 0° 1.00 0° per unit
Ia j0.15 Ib (0.94 j0.342) 1.05 0° per unit
The solutions of the loop currents are as follows:
Ia 0.50505 182.7° 5.04508 j0.02336 per unit
Ib 1.04893 344.1° 1.00901 j0.2866 per unit
The load voltage is calculated:
EL Ib 1.0 20° 1.04893 4.1° per unit

FIGURE 6.19 Voltage and current vectors for Example 6.2.
The transformer secondary currents are calculated:
I1 Ia Ib 0.5045 j0.310 0.592 31.6° per unit

I2 Ia 0.50505 2.7° 0.5045 j0.0238 per unit
The load voltage, load current, and transformer currents are plotted in
Figure 6.19. In the load-balancing scheme, the load-current components of
the two transformers are assumed to be equal to each other and comprise the
total load current when they are added together. Therefore, each of the load-
current components is equal to one-half of the load current:
I L1 I L2 1/2 I 0.5245 344.1° 0.5045 j0.1433 per unit

b
The unbalance-current components are equal to the transformer second-

ary currents minus the load-current components:
I U1 I1 I L1 (0.5045 j0.310) (0.5045 j0.1433)

j0.1667 per unit
I U2 I2 I L2 (0.5045 j0.0238) (0.5045 j0.1433)
j0.1195 per unit
The voltages developed across the paralleling reactors are equal to the unbal-
ance-current components times the impedances of the paralleling-reactor,
which are equal to j1.0 per unit:
E U1 I U1 j1.0 0.1667 per unit

E U2 I U2 j1.0 0.1195 per unit

FIGURE 6.20 Voltage vectors for the load bus voltage and voltages developed across
the paralleling reactors in Example 6.2.
The load voltage and the voltages developed across the paralleling reac-
tors are plotted in Figure 6.20. Note that when E U1 and E U2 are added to the
sensed voltage E L , the resulting voltages tend to cause transformer 1 to lower
taps and transformer 2 to raise taps.
Example 6.3
GenCo Unit 2 is a generating plant with a net output of 1100 MW, capable
of a 90% lagging power factor. The generator step up transformer for the unit
has three 405 MVA FOA single-phase transformers connected in a -Grd.Y
bank. Each of these transformers has a total of eight coolers. The transformer
test report is shown in Figure 3.16 in Chapter 3 of this book.
One summer afternoon with Unit 2 running at full output, a generator
step-up transformer trouble alarm was received in the Unit 2 control room.
An electrical maintenance supervisor was dispatched to the transformers and
he observed that transformer serial number C-05213-5-1 had a high-tempera-
ture alarm, which was confirmed by the indications of the top oil temperature
gauge and the winding temperature gauge. The supervisor also noticed that
half of the cooling fans on that transformer were not running. The circuit
breaker supplying these fans had tripped, and there was evidence of an electri-
cal fault in the control cubicle, severely damaging some relays and wiring. It
was estimated that repairs would take at least 12 h, provided a spare relay
could be found. Meanwhile, the transformer temperature continued to in-
crease.
The plant superintendent had to choose whether to shut down the unit
or reduce the net output. Based on the transformer test report, how much net
output can the transformer bank safely handle with one of the transformers
in the degraded condition described above?

These transformers are cooling class FOA, which means they have no
self-cooled rating. With half of the cooling fans inoperative on Serial Number
C-05213-5-1, it can be assumed that half of the cooling capability of this
transformer is lost. Since the transformers are banked, the load on all three
phases must be reduced to the point where the load on Serial Number C-
05213-5-1 is within its thermal capability.
In order to provide a margin of safety, it was decided not to take credit
for any thermal capability beyond nameplate ratings. Therefore, the new trans-
former loading is to be based on derating the nameplate MVA load of the
affected unit.
From the test report shown in Figure 3.16, the total losses consist of
280.5 kW in core losses and 909.9 kW in copper losses at 405 MVA load,
for a total of 1190.4 kW in losses. These losses must be reduced by 50% with
half of the coolers inoperative.
New total losses 0.5 1190.4 kW 595.2 kW
Since the core losses are not a function of load, these are constant. There-
fore, the new copper losses are calculated as follows:
New copper losses new total losses core losses
595.2 kW 280.5 kW 314.7 kW
Copper losses are proportional to the load current squared. The ratio of
the new copper losses to the nameplate copper losses is equal to the ratio of
the new load current to the nameplate load current.
(New load current) 2 314.7 kW
0.346
(Nameplate load current) 2 909.9 kW
The load current is approximately equal to the MVA load. Therefore, the new
MVA load, based on derating the nameplate MVA load, is found by the fol-
lowing relationship:
New MVA load nameplate MVA load 0.346 1/2
405 MVA 0.588 238 MVA
The load limit of the bank is equal to 3 times the load limit of the affected
transformer. This establishes the net generator output.
Net generator MVA output 3 238 MVA 714 MVA
At a 90% lagging power factor, the net MW output is 90% of the net
generator MVA output:
Net generator MW output 0.9 714 MVA 642.6 MW

This reduces the generator output by approximately 42%, which is still prefera-
ble to shutting it down.
REFERENCE
1. IEEE Std. C57.12.00–2000. IEEE Standard General Requirements for Liquid-
of Electrical and Electronics Engineers, Inc., New York 2000, Page 9.

7
Reading and Applying
Nameplate Information
Every distribution and power transformer has a metal nameplate attached to

the tank that gives vital information on how the transformer is to be connected
and operated. The information is printed or stamped on the nameplate so it
is a permanent part of the transformer. A transformer’s nameplate has been
compared to a birth certificate because it contains so many vital statistics that
will follow it throughout its service life. In this chapter, examples of actual
transformer nameplate information are illustrated and the data provided on
the nameplate are discussed.
7.1 MINIMUM NAMEPLATE REQUIREMENTS

The minimum information to be shown on a transformer nameplate depends
on the KVA rating of the transformer as specified in the standards. The stan-
dards require the following information for transformers rated above 500 KVA
[1].
• Name of manufacturer
• Serial number
• Month/year of manufacture

• Cooling class. Where the class of transformer involves more than
one rating, all ratings are shown. Windings having different ratings
have their individual KVA ratings described. If the transformer has
more than one temperature rating, these ratings are shown on the
nameplate. Provisions for future cooling equipment are indicated.
• Number of phases
• Frequency
• KVA or MVA rating
• Voltage ratings. The voltage ratings of a transformer or autotrans-
former windings are separated by a dash (-).
• Tap voltages. The tap voltages of an individual winding are sepa-
rated by a slash (/).
• Rated temperature rise, °C
• Polarity (single-phase transformers)
• Phasor or vector diagram (polyphase transformers)
• Percent impedance. The percent impedance is specified between
each pair of windings with the voltage connection and the KVA base
stated. The percent impedance shall be tested.
• Basic lightning impulse insulation levels (BIL). The BIL of each
winding and each bushing are specified.
• Approximate mass of the core and coils, tank and fittings, insulating
oil, total weight, and heaviest piece.
• Connection diagram. The connection diagram shows all winding ter-
minations with a schematic plan view showing all fixed accessories.
The schematic plan view generally shows the low-voltage side of
the transformer at the bottom . The location and polarity shall be
shown for all current transformers used for metering, relaying, or
drop compensation.
• Installation and operating instructions references
• The word ‘‘transformer’’ or ‘‘autotransformer’’
• Suitability for step-up operation. Since the MVA rating is generally
specified at the output winding at the nominal output winding volt-
age, the MVA rating for step-up operation will generally be different
than the MVA rating for step-down operation, unless specified.
• Maximum positive and negative operating pressures of the oil preser-
vation system, kPa or psi
• Maximum negative pressure of the tank for vacuum filling
• Liquid level below the top surface of the highest point of the highest
manhole flange at 25°C
• Change in liquid level per 10°C change in liquid level

• Oil volume of each transformer compartment
• Type of insulating liquid. The nameplate shall also have the follow-
ing note: ‘‘Contains no detectable level of PCB (less than 2 PPM)
at the time of manufacture.’’
• Conductor material of each winding
7.2 MANUFACTURER’S INFORMATION

The manufacturer’s name usually appears prominently at the top of the name-
plate. Just below the manufacturer’s name is a unique serial number or shop
order number to identify the particular unit so its manufacturing and design
records can be traced. In some respects, the nameplate is equivalent to a birth
certificate.
7.3 COOLING CLASS, NUMBER OF PHASES,

AND OPERATING FREQUENCY
The transformer cooling class, number of phases, and the operating frequency
are usually specified near serial number. As we saw in Chapter 6, there are
a variety of cooling classes. The more common types are reviewed in Table
6.1.
The second and third cooling stages provide additional loading capabili-
ties with respect to the OA rating. See Table 7.1.
TABLE 7.1 Nominal Ratings of Various Cooling Classes as a Percentage

of the Self-Cooled Rating (per NEMA)
Top rating as a
percentage of
Transformer OA rating Cooling class OA rating
Single phase 501–2,499 KVA

Three phase 501–2,499 KVA OA/FA 115%
Single phase 2,500–9,999 KVA
Three phase 2,500–11,999 KVA OA/FA 125%
OA/FA
OA/FOA 1331/3%
Single phase 10,000 KVA OA/FA/FA
Three phase 12,000 KVA OA/FA/FOA 1662/3%
OA/FOA/FOA
Source: Ref. 2.

7.4 VOLTAGE RATINGS
The voltage rating of the transformer is specified in terms of both the line-
to-line system voltages and the winding voltages. For example, a 230 kV
Grd.Y to 69 kV Grd.Y transformer with a 12.47 kV tertiary would have the
following voltage rating on its nameplate:
230000GR.Y/132800-69000GR.Y/39840-12470
The hyphens separate the voltage ratings of one winding from the voltage
ratings of the other windings. In this illustration, 230000GR.Y/132800 is the
rating of the high-voltage winding, 69000GR.Y/39840 is the rating of the low-
voltage winding, and 12470 is the rating of the tertiary winding. The voltage
ratings are always given in volts.
When a slash is shown in the voltage rating of a winding, this indicates
that the winding is Y-connected with the phase-to-phase system voltage ap-
pearing first followed by the slash and then the winding voltage. The winding
voltage is the phase-to-neutral voltage of the system. If a designator GR.Y,
GRD.Y, or Grd.Y appears, this indicates that the neutral end of the winding
is intended to be grounded, which probably means that there is reduced insula-
tion near the neutral end of the winding. In this case, operating the winding
ungrounded may not be safe.
The example 230000GR.Y/132800-69000GR.Y/39840-12470 desig-
nates the 12,470 V tertiary winding by a single number without a slash ap-
pearing because the winding ratings and the line-to-line voltage of the system
are the same. In other words, the windings are connected phase-to-phase in
a .
If the nameplate designates a winding voltage is designated with a Y
but without a slash, the winding is permanently Y-connected without bringing
out a neutral connection. For example, 66000-12470Y shown on the nameplate
indicates a -connected primary winding rated 66,000 V with a Y-connected
secondary winding suitable for connection to a 12,470 V system.
Example 7.1
Two transformers have the following nameplate voltage ratings:
Transformer 1: 69000-12470GR.Y/7200
Transformer 2: 69000GR.Y/39840-12470
Explain the difference between the two transformers. What are the TTRs
of these transformers? Can the two transformers be operated in parallel?

Transformer 1 has a -connected primary with a line-to-line rating and
a winding rating of 69,000 V. The secondary is grounded-Y connected with a
line-to-line rating of 12,470 V and a winding rating of 7200 V. The TTR of
this transformer equals the ratio of the winding ratings: 69,000/7200 9.583.
Transformer 2 has a grounded-Y connected primary with a line-to-line
rating of 69,000 V and a winding rating of 39,840 V. The secondary is -
connected with a line-to-line rating and a winding rating of 12,470 V. The
TTR of this transformer equals the ratio of the winding ratings: 39,840/
12,470 3.195.
Since the TTRs of these transformers are so different, we could be
tempted to state that they cannot be operated in parallel. The important consid-
eration is not whether the TTRs are the same, but whether the secondary volt-
ages are matched when the primaries are connected to the same source voltage.
If both transformers have the same phase angle displacement, which is 30°
for a standard design, and the percent impedance values are nearly the same,
these transformers may be operated in parallel.
7.5 KVA OR MVA RATINGS

The nominal KVA or MVA ratings are shown on the nameplate for a specified
winding temperature rise and cooling mode. For example, consider an OA/
FOA/FOA cooling class transformer with ‘‘45/60/75 MVA Continuous at
65°C Temperature Rise’’ specified on its nameplate. This transformer is de-
signed to operate continuously at 45 MVA as a self-cooled (OA) transformer,
or at 60 MVA with one stage of forced oil and forced air cooling, or at 75
MVA with two stages of forced oil and forced air cooling with an average
winding conductor temperature at 65°C above the ambient air temperature.
Notice that the ratio of the rating with the first stage of forced cooling to the
OA rating is 60/45 or 1331/3% and the ratio of the rating with the second
stage of forced cooling to the OA rating is 75/45 or 1662/3%, which conforms
to the NEMA standard, as shown in Table 7.1.
Some oil-filled transformers have KVA and MVA ratings specified at
both 65°C rise and 55°C rise. This is because transformers built prior to the
1960s were limited to an average winding temperature rise of 55°C because
of the types of insulating materials that were available at that time. Standard
ratings developed for these transformers were based on the 55°C temperature
rise. Later, improved insulating materials became available, which allowed
transformers to operate at a 65°C temperature rise. The KVA ratings at 65°C
rise were higher than the ‘‘standard’’ ratings that were previously developed.
Therefore, these transformers were built to the ‘‘standard’’ KVA ratings for

FIGURE 7.1 Part of a transformer’s nameplate showing the MVA ratings by cooling
class.
55°C temperature rise but could be operated at higher KVA ratings at 65°C
temperature rise, so both sets of ratings were shown. Today, most transformer
nameplates omit the 55°C ratings entirely and are built for standard KVA
ratings at 65°C temperature rise.
Certain high-performance insulating materials such as Nomex and sili-
cone fluids allow operation at 75°C rise or even higher temperatures. The
nameplate ratings would reflect the KVA ratings at the higher temperature
rise.
For two-winding transformers, there is usually only one set of KVA or
MVA values shown, because it is understood that the primary and secondary
windings must have the same KVA capabilities. This is not true for three-
winding transformers, however, since the tertiary is often not designed to the
same KVA capabilities as the primary and secondary windings. The nameplate
for a three-winding transformer could read as shown in Figure 7.1. Sometimes,
the details of the tertiary ratings are given in the winding connection tables
and diagrams, discussed below.
7.6 WINDING CONNECTION DIAGRAM

The actual winding connections are shown in a diagram with each winding
and its taps labeled. A set of tables then specifies the voltage ratings, ampere
ratings, and the connections for all the available taps. For transformers with
load tap changing equipment, the connection diagrams and the accompanying
tables are quite extensive.
The connection diagram usually also gives the general physical layout
of the transformer, showing the placement of the bushings and the locations
of current transformers (CTs) and a schematic representation of the load tap
changing equipment, including the preventative autotransformer, moving con-
tacts, arcing contacts, transfer switch, and reversing switch.
A portion of an actual nameplate that shows the winding connection
diagram is illustrated in Figure 7.2. The nameplate depicted is rather interest-
ing. The transformer has a load tap changer. From the connection diagram we

FIGURE 7.2 Part of a transformer’s nameplate showing the voltage ratings, MVA
ratings, percent impedances, connection diagram, physical layout, vector diagram, tap
connections, CT connections, and BIL ratings.

see that the buried tertiary is also a tapped winding that supplies a buck/boost
voltage to the secondary windings through auxiliary transformers connected
between the tertiary and the secondary. Therefore, the tertiary simultaneously
provides four important functions:
1. It provides a path for third harmonic currents.
2. It helps stabilize voltages in the Y-Y primary-secondary connection.
3. It provides a grounding bank action by providing a path for zero-
sequence currents.
4. It provides the necessary voltage taps for regulating the low-side
voltage.
The only function that the buried tertiary cannot perform is to supply
an external load. The voltage rating of the buried tertiary is not given because
it cannot be connected to a system voltage, but one corner of the connection
is grounded internally. This grounding is done so the winding potential voltage
does not ‘‘float’’ because of capacitive coupling to the other windings. With-
out this ground connection, capacitively induced voltages are indeterminate
and could be large enough to cause insulation damage.
The voltage taps for the primary and secondary are shown on the connec-
tion diagram and on the winding rating tables in Figure 7.2. These also specify
which terminal numbers and letters are connected for each tap. This trans-
former has a total of 14 current transformers that are used for metering, protec-
tive relaying, and other purposes. Note the CTs marked ‘‘LDC’’ and ‘‘WDG.
TEMP.’’ The term LDC stands for line drop compensation. The LDC CT
supplies metered line current to a compensating device in the voltage regu-
lator controls. The compensating device effectively moves the voltage control
point into the system connected to the secondary winding. The CT labeled
WDG.TEMP supplies current to the winding temperature gauges. As previ-
ously discussed, these gauges use a heating element surrounding a temperature
probe mounted in the top oil in order to mimic the winding temperature. The
ratios of these CTs would be shown on an actual nameplate, but this informa-
tion is not shown in Figure 7.2.
Just below the connection diagram is a layout sketch showing the physi-
cal locations of the bushings, the load tap changing compartment and the op-
erating handle for the tap changer at deenergized conditions.
The load tap changer is represented schematically in the connection dia-
gram. Note the terminals labeled P1, P2, and P3. These terminals correspond to
the connections to the preventative autotransformer. The two series arcing con-
tacts per phase that are in series with the movable contacts are shown as well.

7.7 PHASOR OR VECTOR DIAGRAM
All nameplates for polyphase transformers include vector diagrams to show
the phase relationships between the windings. If the transformer has a nonstan-
dard phase shift, this will be indicated on the vector diagram. Some transform-
ers have terminal boards that can be wired to provide different configurations
such as either -Y or Y-Y, or unusual phase displacements, such as Y-Y with
a 180° phase displacement between the primary and secondary. Each of the
possible configurations is shown on the vector diagram.
The vector diagram on the nameplate shown in Figure 7.2 shows the
standard phase angle displacement of 0° for a Y-Y connected transformer.
7.8 WEIGHTS AND OIL CAPACITY

To avoid mechanically overloading equipment when handling and rigging
large transformers, weight is an important consideration. Also, if insulating
oil is to be removed for shipping, it is important to know quantities of oil that
are involved. The nameplate provides a convenient reference for these data,
which is permanently attached to the transformer. The nameplate has a table
of approximate weights (that are usually somewhat conservative) and the oil
capacity, usually given in U.S. gallons.
The weights and oil volumes are broken down by components and oil
compartments. The untanking weight is the weight of the heaviest piece that
must be lifted for disassembly. There is also information showing the internal
oil level at 25°C that is used to properly fill the transformer, plus an indication
of the change in oil level per change in temperature. Figure 7.3 shows the
manner in which this information is typically shown on actual nameplates.
Example 7.2
A transformer is to be loaded onto a rail car after the oil is drained from the
main tank and the LTC compartment. A 150 T crane is available. Using the
information in Figure 7.3, is the crane’s capacity adequate?
The untanking weight of the unit (core and coils) is 118,000 lb and the
weight of the tank and fittings is 88,000 lb. Thus, the net weight of the trans-
former without oil is 118,000 lb 88,000 lb 206,000 lb 103 T. The
capacity of the crane is adequate to lift the transformer without oil. Note that
when the transformer is filled with oil, the total weight is 306,200 lb 153.1
T, which exceeds the capacity of the crane.

FIGURE 7.3 Part of a transformer’s nameplate showing weights, oil capacities, oil
level, and operating pressure range.
Example 7.3
The oil level of a particular transformer is shown in Figure 7.3. The trans-
former is being filled with oil at a substation at an ambient temperature of
30°C (86°F). Where should the oil level be after when the filling is complete?
According to Figure 7.3, the oil level at 25°C is 12.6 in. below the top
of the manhole. The change in oil level is 1.17 in. per 10°C change in oil
temperature. Since the ambient temperature is 5°C the reference temperature,
the change in oil level is one-half of 1.17 in., or 0.585 in. above the reference
point of 12.6 in. Therefore, the proper oil level is 12.6 in 0.585 in. 12.015
in. below the top of the manhole.
7.9 OPERATING PRESSURE RANGE

Most modern power transformers are designed to be ‘‘vacuum oil filled.’’
Vacuum oil filling is a process that will be covered in more detail in Chapter
8. Before attempting to ‘‘pull vacuum’’ on a transformer, it is important to
consult the nameplate first to verify that the tank is designed to withstand the
negative pressures. The positive range of operating pressures is also specified
on the nameplate.
The nominal atmospheric pressure is 14.7 psi at sea level. Thus, when

the transformer contains a perfect vacuum, the negative pressure on the tank
will be approximately 15 psi at sea level, and slightly less at higher elevations.
In the example shown in Figure 7.3, we see that this transformer is designed
to be vacuum oil filled under a ‘‘perfect vacuum’’ equal to about 15 psi of
negative pressure.
7.10 IMPEDANCE
The transformer impedance, sometimes referred to as ‘‘impedance volts’’ on
the nameplate, is specified for each of pair of windings as a percent value on
a specific KVA base. For two-winding transformers, only one value of imped-
ance is given, corresponding to the high-to-low voltage series impedance at
a KVA base that usually corresponds to the KVA rating of the primary and
secondary windings. For a transformer having multiple cooling classes, the
KVA base is usually specified as the OA rating of the transformer.
For a transformer having three or more windings, the situation is compli-
cated by the fact that not all of the windings have the same KVA rating.
Therefore, the KVA base used to for the percent impedance of each pair of
windings must be specified on the nameplate.
For example, a three-winding transformer may have its impedances
shown on its nameplate as shown in Figure 7.4. Note that the percent imped-
ance between the primary and secondary windings is on a higher KVA base
than the percent impedances given for the primary to tertiary and the secondary
to tertiary. When doing analysis using the nameplate impedance values, care
must be exercised to convert the percent impedances to a common KVA base.
Since the nameplate is normally fabricated before transformer assembly
is completed, some of design data is etched on the nameplate. The last two
items to be determined are the transformer serial number and the percent im-
pedance values that must be determined by test. Therefore, the percent imped-
ances are usually stamped on the nameplate just before the transformer is
shipped from the factory.
FIGURE 7.4 Nameplate designation of percent impedances of a three-winding trans-

former.

Example 7.4
Convert the percent impedance values shown in Figure 7.4 into per unit imped-
ances on a common 100 MVA base.
Primary to secondary: 0.16 100 MVA/75 MVA 0.213 per unit

Primary to tertiary: 0.14 100 MVA/26.26 MVA 0.533 per unit
Secondary to tertiary: 0.12 100 MVA/26.26 MVA 0.457 per unit
7.11 BASIC INSULATION LEVEL

The basic insulation levels (BILs) of the windings at each of the terminals
and the BIL of the bushings are shown on the nameplate. These are given as
full-wave test values in kV.
FIGURE 7.5 Overall layout of the complete transformer nameplate.

7.12 NAMEPLATE LAYOUT
There is some flexibility in the standards as to how the nameplate is to be
laid out. Each manufacturer arranges the data somewhat differently. Some
customers specify a particular layout that is suitable to their needs. Figure 7.5
shows one typical nameplate layout as a block diagram.
REFERENCES
of Electrical and Electronics Engineers, Inc., New York, 2000, pp. 24–26.
2. NEMA Standards Publication No. TR 1–1980. Transformers, Regulators and
Reactors. Washington, DC: National Electric Manufacturers Association, Part 0,
p. 1.

8
Maintenance, Testing,
Troubleshooting, and Reliability
Now that we are familiar with the fundamentals of transformer theory, design,
and operation, these principles can be applied to maintenance, testing, and
troubleshooting. A transformer may have a very long life, or it may fail min-
utes after first being energized.
The life of an average transformer usually depends to some extent on
how well it is treated. Since large power transformers can cost several millions
of dollars, performing regular transformer maintenance is a very cost-effective
practice.
8.1 GOOD UTILITY PRACTICES

Utility companies have enormous amounts of money invested in transformers
of all types, including distribution and power transformers. Utilities also have
a long history and have developed methods, procedures, and philosophies that
over time have proven very effective in prolonging equipment life. These are
collectively referred to as good utility practices and it is instructive to review
these practices as applied to power transformers.
One utility has an instruction [1] that covers the testing, inspections,
operation, and maintenance of power transformers during the entire operating

lifetime, which are considered good utility practices. This instruction is sum-
marized in the following sections.
8.1.1 Scope
Receiving, storing, installing, testing, operating, maintaining, and inspecting
all power transformers with a nominal voltage of 2300 V or higher on the
low-voltage winding. This instruction does not cover all details found in manu-
facturer’s instruction book.
8.1.2 Schedule for Tests, Inspections

The schedule for all required tests and inspections is listed on Power Trans-
former Acceptance and Maintenance Checklist (see Table 8.1.8)
8.1.3 Receiving New or Rebuilt Transformers

Inspect new or rebuilt transformers promptly for manufacturing errors, or ship-
ping damage.
• Upon delivery, prior to unloading, System Shops will inspect the

transformer.
• Complete all inspections in the On Car Inspect column of Power
Transformer Acceptance and Maintenance Checklist.
• Send copies of the completed checklist to the Regional Technical
Support Engineer and the Substation Component Engineer.
8.1.4 Handling and Shipping

Follow these precautions when moving transformers:
• Lift transformers only by the means provided, and use spreaders to

balance the lift when necessary.
• When lifting accessories, use lifting eyes provided for this purpose,
and attach lag lines to control the load at all times.
• Always handle transformers in the upright position unless the manu-
facturer indicates it can be handled otherwise.
• A list of accessories and parts removed for shipping a transformer
should be prepared by the disassembling crew and forwarded to the
crew leader receiving the unit so that he or she can determine
whether all parts have been received.
• When bushings are removed for shipment, the internal leads should

be securely tied to bushing cover plates with linen tape to prevent
them from moving during shipment.
8.1.5 Storage
Bushings, radiators, or other accessories removed from transformers should
be tagged by the person removing them to identify the transformer from which
they are removed.
Storing Transformers
• Place transformers on sound footing in a safe or protected area.
• Seal all openings where accessories have been removed with steel
shipping covers.
• Gaskets should be installed with cover plates.
• All sealed transformers should be purged and pressurized with dry
nitrogen for short term storage less than 6 months.
• Refer to manufacturer’s instruction book for specific instructions on
storing transformers in oil or nitrogen.
Storing Bushings
• Bushings should be left in transformer if possible.
• If removed, store bushings in a clean, dry place indoors, protected
from damage. Oil-filled bushings can be stored in an open area pro-
tected from weather.
• Preferred storage of oil-filled bushings is vertical, but oil reservoirs
must be elevated at least 10 in. above bottom bushing stud (or other
height specified in instruction book).
Storing Radiators and Other Accessories
• All openings on detached radiators must be sealed from moisture
and the radiators stored so water cannot stand around the sealed
openings.
• Protect all accessories from damage, moisture, and foreign materials.
8.1.6 Acceptance for Service

All transformers, old or new, moved to a substation for installation must be in-
spected and tested before energizing. The final acceptance for service of all trans-
formers is the responsibility of the Regional System Maintenance Supervisor.
• Complete all sections of the Accept at Sub column of the Power Trans-
former Acceptance and Maintenance Checklist (see Table 8.1.8).

• Report unsatisfactory test results to the Technical Support Engineer
and the Substation Component Engineer.
8.1.7 Safety Precautions

Follow all rules and procedures in both the Safety Rule Book and Safety Proce-
dures for Confined Space Entry. Also follow these precautions when working
on power transformers.
Oxygen Test
Since nitrogen (which cannot support life) is normally used in the gas space
above the oil in transformers, an oxygen-testing device must be used to check
the oxygen content prior to entry into the tank. Also, monitor the oxygen
content while working inside the transformer.
Caution: Never Enter a Transformer if the Oxygen Content is Less Than 19.5%.
Combustible Gas Test
Before entering a transformer, test for combustible gas. The maximum accept-
able level of combustible gas for safe entry is 10% of the lower explosive
limit (LEL).
Carbon Monoxide Test
A carbon monoxide test should be performed before entering a transformer.
Carbon monoxide (CO) should be less than 25 parts per million (ppm).
Ground to Guard Against Static Charges
Static charges can develop in the windings during electrical tests and in the
transformer oil as it flows through pipes, hoses and tanks.
During oil flow into any tank, ground the tanker, filter press, piping,
transformer tank and all bushings or winding leads. These grounds should be
maintained for at least an hour after oil flow has ceased.
To avoid charges in the transformer windings, ground the windings be-
fore and after performing winding electrical tests. If the transformer tank is
not permanently grounded, ground it temporarily during the test.
8.1.8 Internal Inspection Precautions

Internal inspections are listed in Power Transformer Acceptance and Mainte-
nance Checklist. They are required for all new or rebuilt units when received,
and for all units when placed in service at substations. Follow the guidelines
below when making internal inspections.

• Do not open transformers during periods of fog or precipitation or
when relative humidity exceeds limits outlined in the manufacturer’s
instruction book. If no value is specified in the instruction book, use
a limit of 75%.
• Do not allow transformer to stand open any longer than is necessary
because of its tendency to absorb moisture from the air.
• If the core and coils are not covered with oil, maintain a flow of dry
air through the tank while it is open to help keep the insulation dry.
• For oil-filled units, lower the oil to the top of the core and coil assem-
bly. Oil must be passed through an approved filter system. If possi-
ble, do not permit the coils and insulation to be exposed to the air.
• Check oxygen content before entry and monitor while inside the
tank. Minimum acceptable level of oxygen is 19.5%.
• No one shall enter confined spaces without prior authorization and
review of applicable Company safety rules and General Safety Pro-
cedures for Confined Space Entry.
• Before climbing on the transformer, remove anything that may con-
taminate it and cause it to fail when energized:
Remove all items from pockets and other loose items such as
watches and rings.
Wipe shoes clean of mud, stones, and other foreign material.
Put clean disposable booties over shoes prior to entering the trans-
former.
Attach lines to tools used in tank or near open manhole so that they
cannot accidentally be dropped in the transformer.
• Before replacing manhole covers, check the gaskets.
• After sealing the transformer (unless it is the open type), it should
be pressurized with dry nitrogen and purged until oxygen content is
less than 1%.
8.1.9 Test Procedures

Required tests and their schedules are listed for all new and existing transform-
ers on Power Transformer Acceptance and Maintenance Checklist. Report
any unsatisfactory results to the Regional Technical Support Engineer and the
Substation Component Engineer.
Core Ground Test
The core ground test (performed on core form units only) determines the pres-
ence of unintentional ground on the transformer core by checking the core

ground insulation resistance using a 1000 V megger with the factory core ground
disconnected. Test values corrected to 20°C should be 25 MΩ or greater. Record
results on Power Transformer Acceptance and Maintenance Checklist.
Transformer Turns Ratio (TTR) Test
The TTR test measures the turns ratio of the windings and detects open-
circuited and short-circuited turns.
• For proper connections to transformers, refer to TTR test set instruc-
tion book.
• Perform test on all tap positions.
• Set transformer on tap to be used and retest. Results on each tap
should be within 0.5% of the theoretical turns ratio.
HV coil rating
Theoretical ration !
LV coil rating
• If satisfactory TTR test results cannot be obtained on all phases, not

only the phase or phases that are unsatisfactory, note either of the
following:
High exciting current and low voltage on TTR test set (indicative
of a short circuit on one of the windings)
Normal exciting current and normal voltage but no galvanometer
deflection on TTR test set (indicative of an open circuit)
• Record test results on TTR Test Results form.
Doble Test
The Doble test is performed on transformer windings and bushings by an
Insulation Technician. The test is a relative measure of the condition of the
insulation. The Insulation Technician will make recommendations.
Megger Test
The megger test is a measure of the insulation resistance. Remove solid con-
nections of windings to ground. The following tests are made using a 1000
V megger:
• Measure from the high-voltage winding to the low-voltage winding

and ground. (Low-voltage winding is grounded.) H-LG
• Measure from the low-voltage winding to the high-voltage winding
and ground. (High-voltage winding is grounded.) L-HG
• Measure from the high- and low-voltage windings to ground. HL-G
• Megger readings are temperature dependent. Correct all the above

TABLE 8.1.1 Temperature Correction Multipliers
for Insulation Resistance Measurements
Oil temperature, °C Oil temperature, °F Multiplier
0 32 0.25
5 41 0.36
10 50 0.50
15.6 60 0.74
20 68 1.00
25 77 1.40
30 86 1.98
35 95 2.80
40 104 3.95
readings to 20°C by multiplying the megger readings by the multipli-

ers shown in Table 8.1.1.
• The readings for the H-LG, L-HG, and HL-G tests should be compa-
rable to prior megger readings, with all readings corrected to 20°C
(68°F).
• If previous readings are not available, the minimum acceptable resis-
tance for each reading is per Table 8.1.2.
• Record megger readings on Megger Test Results form.
Oil Tests
Warning! To prevent air from being drawn into transformers with sealed-tank
or gas-oil-seal designs, make sure the gas space above the oil is at a positive
pressure before opening the drain valve.
For all transformers, perform oil dielectric and acidity tests. Refer to
instruction: Insulating Oil: Using, Handling, Sampling, and Testing. Record
results on Power Transformer Acceptance and Maintenance Checklist. For
new and rebuilt transformers, send oil samples for additional tests to the Chem-
ical Laboratory. A copy of the test results should be sent to Substation Compo-
nent Engineering.
TABLE 8.1.2 Insulation Resistance Limits

Rated voltage of Minimum
winding under test acceptable resistance
2300 V to 13,200 V 800 MΩ

Above 13200 V 1600 MΩ

Oxygen Content Test
High oxygen content results in oxidation of oil, which causes sludging. The
gas space in all sealed transformers is to be tested semiannually for oxygen
content. Record results on Power Transformer Acceptance and Maintenance
Checklist. Oxygen content should not exceed 5%. When necessary, the gas
space should be purged with dry nitrogen until the oxygen content is 1% or
less.
Excitation Test
This test is done with Doble equipment by the Insulation Technician, who
will make recommendations.
Gas-in-Oil Analysis
Semiannually, samples of oil are to be taken for gas-in-oil analyses from all
69 kV and above power transformers and generating station transformers.
8.1.10 Vacuum Oil Filling

Vacuum filling is required for new or repaired transformers that are shipped
without oil. Use Table 8.1.3 to determine if vacuum oil refilling is required for
a transformer that has been drained or opened for inspection or maintenance.
TABLE 8.1.3 Requirements for Vacuum Oil Filling

If the transformer
operating voltage is And the core and coils Then vacuum oil refilling is
115 kV and above ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯→ Required: Follow steps 1–10

below, under ‘‘Vacuum Oil
Have been exposed to Filling’’
atmosphere
Below 115 kV Have not been exposed to Not required: Add oil by pump-
atmosphere ing into the top filter press
connection. When oil filling
is completed and prior to en-
ergizing, allow the trans-
former to stand. Use the
chart in step 10 for the
proper hold time.

TABLE 8.1.4 Oil Filling Requirements for Various Transformer Compartments
And the tank And the tank

is being filled And the tank is is being filled
LTC compartment type (‘‘Original Fill’’) being topped off after Maint./Repair
Selector switch Vacuum fill Degassed oil* Degassed oil*

Vacuum interrupter Vacuum fill Degassed oil* Vacuum fill
Diverter switch Filtered oil Filtered oil Filtered oil
Arcing-type switch Filtered oil Filtered oil Filtered oil
Reactor compartment Vacuum fill Degassed Oil* Degassed Oil*
* Degassed Oil–Oil that has been vacuum processed prior to storage.
When oil filling an LTC compartment, use Table 8.1.4 to determine

what type of oil filling is required.
When transferring oil to a power transformer, pass the oil through an
approved filter system to remove moisture and sediments.
Caution: Never Energize an Underfilled or Overfilled Power Transformer.

Precautions for Vacuum Oil Filling
• Apply vacuum only to transformers designed for vacuum filling.
(Noted on Nameplate.)
• Never stand on top of a transformer while vacuum is applied.
• Never energize a transformer while vacuum is applied.
• Some transformers require removable vacuum bracing; consult man-
ufacturer’s instructions and drawings.
• Remove pressure relief devices and sudden pressure relays and seal
openings to prevent damage or misoperation due to changes in pres-
sure when vacuum filling.
Warning! When a transformer has load tap-changing compartments, it may

be necessary to apply vacuum simultaneously to equalize pressures. Consult
manufacturer’s instructions.
Procedure for Vacuum Oil Filling
1. Remove all oil from the transformer.
2. Test new, unprocessed oil for dielectric strength using ASTM
Method D877. The oil must have a minimum breakdown voltage
of 30 kV.

TABLE 8.1.5 Dew-Point Limits Based on Insulation Compartments
Insulation Max dew Insulation Max dew Insulation Max dew

temp., °F point, °F temp., °F point, °F temp., °F point, °F
0 "78 40 "44 80 "10

5 "74 45 "40 85 "6
10 "70 50 "35 90 "1
15 "66 55 "31 95 3
20 "64 60 "27 100 7
25 "58 65 "22 110 16
30 "53 70 "18 120 25
35 "48 75 "14 130 33
3. After assembly, pressurize the transformer to 2 psig by adding dry

nitrogen. Check the transformer for leaks.
4. For transformers rated 115 kV and above, after waiting for a 24
h period, make a dew-point check to determine the dryness of the
transformer insulation. For new transformers and transformers in
warranty, refer to the manufacturer’s instructions for acceptable
dew-point readings. For transformers not in warranty, refer to Ta-
ble 8.1.5. If it does not pass dew-point test, a hot oil dryout is
required. After dryout, repeat step 4.
5. Draw a vacuum of 2 mmHg or less. Hold this vacuum for a period
of time specified in the manufacturer’s instruction book, if the
transformer is new or in warranty. If the transformer is not in war-
ranty, use Table 8.1.6.
6. Maintaining a vacuum of 2 mmHg or less, admit oil into the top
of the transformer connection. Once oil filling is started, it must
not be interrupted. Oil degassing equipment is required for trans-
formers rated 115 kV and above.
7. If the transformer is a conservator type, stop filling when oil
reaches a level 2 in. below the transformer cover. If the transformer
TABLE 8.1.6 Vacuum Hold Time Prior to Oil-Filling Transformer
If transformer operating voltage is Then the vacuum hold time is
Less than 115 kV 4h

115–345 kV 6h
Above 345 kV 12 h

TABLE 8.1.7 Stand Time Prior to Energizing a Transformer
If transformer operating voltage is Then allow to stand
Less than 115 kV 6h

115–345 kV 12 h
Above 345 kV 24 h
is equipped with a nitrogen bottle, stop filling when the oil level
gauge is slightly over the 25°C level. This is to compensate for the
transformer expanding when vacuum is broken and for oil cooling.
8. Break the vacuum with dry nitrogen. If the transformer has a con-
servator with air bag, or air separation membrane, add the re-
maining oil to the expansion tanks in accordance with the manufac-
turer’s recommendations.
9. Bleed the air from transformer oil pump vents. Turn on all pumps
and leave them running while the oil cools.
10. Allow the transformer to stand before energizing (with oil pumps
running) according to the timetable shown in Table 8.1.7. Run one
half of the pumps for half the time and the other half of the pumps
for the second half of the time.
11. Prior to energizing the transformer, check oil levels in all compart-
ments. Pump oil into the top, if necessary, to raise the oil level to
the 25°C mark.
12. Prior to energizing the transformer, shut off all oil pumps and place
controls on automatic so that no pumps are running prior to ener-
gizing. This is important to eliminate static electrification of the
oil, which could cause an internal failure. This hold time must be
a minimum of 12 h.
8.1.11 Maintenance of Spare Transformers

Usable transformers stored as system spares shall receive the following mini-
mum maintenance checks every 6 months except as noted. Failed units
awaiting disposition require no periodic maintenance.
• Oil sample and dielectric test (check yearly)
• Nitrogen pressure
• Oil level
• Visual inspection, including check for oil leaks and rust
• Operation of control cabinet heaters

TABLE 8.1.8 Power Transformer Acceptance and Maintenance Checklist
Substation Bank No. Transformer No.

Mfr. Serial No. Voltage Rating KVA
On car Accept
Item inspect at sub 1 month 6 months 1 year
1. Megger test (enter readings below) ! !
HL-G MΩ
H-LG MΩ
L-HG MΩ
2. Core ground MΩ ! !
3. Doble test (every 8 years) !
4. TTR test (all tap positions) ! ! !
5. Oil dielectric kV ! ! !
6. Oil acidity Mg KOH ! ! !
7. Oxygen content % ! ! !
8. Excitation test !
9. New oil test (Chemical Lab) ! !
10. Gas-in-oil sample ! !
11. Oil sample ! ! !
12. Oil temperature ! ! !
13. Winding temperature ! ! !

14. Load current (tong ammeter) ! ! !
15. Voltage ! ! !
16. Oil level ! ! ! ! !
17. Nitrogen Pressure ! ! ! ! !
18. Automatic gas-seal equipment ! ! ! !
a. Pressure gauge ! ! ! !
b. Gas cylinder content ! !
c. Low-pressure alarm circuit ! !
19. Fan motors—lubrication ! !
20. Heat exchanger clear of obstruction ! !
21. Breather openings clear ! ! !
22. Openings, gaskets, and springs of pressure relief valves !
23. Pressure relief semaphore ! ! ! ! !
24. Opening in pressure-vacuum bleeder !
25. Tank grounds ! ! ! !
26. Supervisory circuits !
27. Check for oil leaks ! ! ! ! !
28. Operation of sudden pressure relay, thermal overload and oil !
temperature indicators
TABLE 8.1.8 Continued
On car Accept
29. Calibrate oil temperature indicator !
30. Calibrate thermal overload device (per Relay Test Dept. !
schedule)
31. Oil pump operation and correct flow ! ! ! !
32. Oil pump bearing wear measurement !
33. Check for unusual noises ! ! ! !
34. Weathertightness of control cabinet ! ! ! !
35. Tightness of control wiring conn. ! !
36. Check control switch operation ! ! ! !
37. Operation and tightness of gauges, valves, and fittings ! ! ! !
38. Check control cabinet for corrosion ! ! ! !
39. CT connections, polarity, and ratio !
40. Differential relay (Test Dept. Schedule) !
41. Check for saturation of silica gel breather ! ! !
42. Examine impact recorder tape !
43. Check for movement on RR car !
44. External shipping braces !
45. Check relative humidity before opening tank ! !

46. Condition of paint ! ! ! ! !
47. Check all accessories for absence or damage ! !
48. Check nameplate for correctness ! !
Internal. Check for Oxygen Content Before Entering (Min. 19.5%)
49. Core ground (core form units) MΩ ! !
50. Check bushing leads for condition, length, and connections ! !
51. Wood-blocking and lead supports ! !
52. Examine all visible insulation ! !
53. Internal shipping braces ! !
54. Check for shifting of core and coils ! !
55. Check for loose or missing bolts, nuts, and connecting links ! !
56. Tap changer gear box lubrication !
57. Tap changer check operation ! !
58. Tap changer contact alignment and pressure ! !
59. Tap changer check operating shaft ! !
60. Tap changer check discoloration of current-carrying parts ! !
Bushings
61. Surfaces clean ! ! ! !
TABLE 8.1.8 Continued
On car Accept
62. Inspect for cracks ! ! ! ! !
63. Oil level ! ! ! ! !
64. Oil leaks ! ! ! ! !
65. Connectors, bolts, clamps, and top terminals (every 8 years) ! !
66. CTs centered, insulation OK, clamps tight (every 8 years) ! !
67. Leads clear, not straining bushings (internal and external) ! ! ! ! !
68. Calibrate bushing potential device (Test Dept. Schedule) !
69. Check for radio noise ! ! !
Radiators
70. Condition of paint ! ! ! ! !
71. Check for oil leaks on fins, headers, and valves ! ! ! ! !
72. Check bracing ! ! ! ! !
Load tap changers—except vacuum-type LTC components in oil
which are on 4-year cycle
73. Check oil in arcing compartment—change if necessary ! !
74. Oil sample from selector switch compartment ! !
75. Pressure relief valve/breather clear ! ! ! !
76. Check all contacts ! !

77. Check motor lubrication ! !
78. Check mechanism lubrication ! !
79. Visual inspection of mechanism ! ! ! !
80. Motor contactor contacts ! ! ! !
81. Mechanism brakes ! !
82. Gaskets—replace if necessary ! !
83. Selsyn devices—check lubrication ! !
84. Operation counter and position indicator ! ! ! !
85. Clean all insulating parts ! !
86. Check stuffing boxes for leaks ! !
87. Operation of mechanisms ! !
88. Tightness of all connections and nuts and bolts ! !
89. Check for loose or damaged parts and cracked porcelain ! !
90. Calibration of voltage regulating relays !
91. Contacts on voltage regulating relays and motor operating and
auxiliary relays (Test Dept. Schedule) !
Completed by Date
Work Order No. Date
8.2 PREVENTATIVE MAINTENANCE VERSUS
PREDICTIVE MAINTENANCE
Some of the activities mentioned in the O&M instruction above are preventative
maintenance activities while others fall under the predictive maintenance cate-
gory. The aim of preventative maintenance is to keep components from aging
and wearing out, or to restore and replace aged or worn components before they
fail. Preventative maintenance is scheduled periodically or performed on some
other timetable based on past experience of the component failure modes.
The aim of predictive maintenance, on the other hand, is to detect aging
or wear in components so that preventative maintenance can be performed
before ultimate failure occurs. Predictive maintenance is commonly referred
to as testing. The requirements for a good test are as follows:
• The test should have sensitivity; in other words, it should give an
early warning of impending trouble.
• The test should have selectivity; in other words, it should not give
off false positive indications of trouble and should give a clear indi-
cation of what is wrong.
• The test should be practical; in other words, it should not require
exotic test equipment or an unusually high skill level to perform the
test or interpret the results.
• The test should be nondestructive.
8.3 FACTORY TESTS

Every transformer that is manufactured undergoes some form of factory test-
ing. For power transformers, these tests are quite extensive and a certain per-
centage of test failures do occur. Typically around 5% of the transformers
produced will fail at least one of these tests. Test requirements are spelled out
in a number of industry standards and specifications [2,3].
There is some overlap among industry standards with respect to testing.
In recent years ANSI/IEEE Standard C57.12.90 has been generally adopted by
the other standards for testing liquid-immersed distribution, power, and regulat-
ing transformers. Some of the more significant standard factory tests specified
in ANSI/IEEE Standard C57.12.90 are itemized in the following sections.
8.4 RATIO TEST

This test determines the ratio (TTR) of the number of turns in the high-voltage
winding to that in the low-voltage winding. The ratio test shall be made at
rated or lower voltage and rated or higher frequency. In the case of three-

phase transformers when each phase is independent and accessible, single-
phase power should be used, although three-phase power may be used when
convenient. The tolerance for the ratio test is 0.5% of the winding voltages
specified on the transformer nameplate.
The accepted methods for performing the ratio test are the voltmeter
method, the comparison method, and the ratio bridge. With the voltmeter
method, the primary winding is excited at rated frequency and the voltage at
the primary and the open-circuit voltage of the secondary winding are mea-
sured. The ratio is the primary voltage divided by the secondary voltage. The
comparison method applies voltage simultaneously to the transformer under
test and the open-circuit secondary voltages are measured and compared.
The ratio bridge method is the most accurate method and can easily
determine the TTR to the very small tolerances required by the standard. The
test apparatus is commonly referred to as a TTR Test Set. One such test set
is manufactured by the Biddle Company and has proven to be especially useful
as a diagnostic test in the field, so its operation will be described in detail.
This test set is shown in Figure 8.1.
The clamp test leads are connected to the secondary winding of the
FIGURE 8.1 Circuit diagram of a TTR test set.

transformer under test and the clip leads are connected to the primary winding
under test. The secondary winding of the transformer under test and the sec-
ondary of a calibrated reference transformer in the test set are both excited
by the same 8 V source voltage from a hand-cranked generator. A voltmeter
is used to verify that the correct voltage is being applied.
An ammeter measures the exciting current into the transformer under test.
When the voltage developed across the primary of the transformer under
test (1-2) is equal to the voltage developed across the primary of the calibrated
reference transformer (2-3), then the voltage across the synchronous rectifier is
zero and the galvanometer detector reads zero. With more voltage developed
across 1-2 than across 2-3, the galvanometer has a negative deflection. With less
voltage developed across 1-2 than across 2-3, the galvanometer has a positive
deflection. The ratio dials are used to adjust the ratio of the reference transformer.
A simplified equivalent circuit of the TTR test set is shown in Figure
8.2. The transformer under test is also shown. Note that the current through
the detector, labeled ‘‘Det’’ in the figure, is zero when the voltages developed
FIGURE 8.2 Simplified circuit of a TTR test set.

at the high-voltage terminals of the test-set transformer and the transformer
under test are equal. This condition exists when the ratios of the test-set trans-
former and the transformer under test are equal.
8.5 OTHER FACTORY TESTS

The remainder of the factory tests are briefly summarized below. The details
of the test set connections and formulas are beyond the scope of this book
and the reader is directed to ANSI/IEEE Standard C57.12.90 for these details.
• No-Load Losses. The tests measures the no-load losses at specified

excitation voltage and a specified frequency. Sine-wave voltages are
used unless a different waveform is inherent in the operation of the
transformer. The recommended method is the average-voltage volt-
meter method, employing two parallel-connected voltmeters. One
voltmeter is an average-responding but RMS calibrated voltmeter
and the other voltmeter is a true RMS-responding voltmeter. The
test voltage is adjusted to the specified value as read by the average-
responding voltmeters. The readings of both voltmeters are used to
correct the no-load losses to a sine-wave basis.
• No-Load Excitation Current. This current is measured in the wind-
ing used to excite the transformer with the other windings open-
circuited. It is generally expressed in percent of the rated current of
the winding. No-load excitation current is not sinusoidal and con-
tains, as we have seen, odd harmonics (predominantly third har-
monic current). The ammeter used to record the no-load excitation
current is an RMS meter which reads the square root of the sum of
the squares of the harmonic currents.
• Load Losses and Impedance Voltage. The transformer must be in a
specific state before the load losses and impedance voltage are mea-
sured. The temperature of the insulating liquid must be stabilized
and the difference between the top and bottom oil temperatures shall
be less than 5°C. The winding temperatures must be measured (using
a resistance method) before and after the test and the average taken
as the true temperature. The difference in the winding temperature
before and after the test must not exceed 5°C. The two test methods
for measuring load losses and impedance voltage are the wattmeter-
voltmeter-ammeter method and the impedance bridge method. These
tests generally apply a reduced voltage to one set of windings with
the other set of windings short-circuited. For three-winding trans-

formers, these tests are repeated for each combination of windings
taken two at a time.
• Dielectric Tests. These tests consist of applied-voltage tests and
induced-voltage tests. Applied-voltage tests apply a high voltage to
all bushings of a winding, one winding at a time, with the other
windings grounded. A 60 Hz voltage is increased gradually over 15
s and held for 40 s and reduced to zero over 5 s. Induced-voltage
tests apply a high voltage across a winding with the other windings
open-circuited in order to test the quality of the turn-to-turn insula-
tion. In order to prevent core saturation at the higher excitation volt-
age, the frequency of the induced-voltage test is increased (typically
around 120 Hz). The induced voltage is applied for 7200 cycles or
60 s, whichever is shorter.
• Switching Impulse Test. The switching impulse test applies a switch-
ing impulse wave between each high-voltage line terminal and
ground. The test series consists of one reduced voltage wave (50%–
70% of specified test level) followed by two full-voltage waves. Ei-
ther positive or negative polarity waves, or both, may be used. A
voltage oscillogram is taken for each applied wave. The test is suc-
cessful if there is no sudden collapse of voltage. Successive oscillo-
grams may differ because of the influence of core saturation.
• Lightning Impulse Test. The test sequence consists of one reduced
full wave, two chopped waves, and two full waves. Tap connections
are made with the minimum effective turns in the winding under tests
and regulating transformers are set to the maximum buck position.
Oscillograms are taken of each wave. The general technique for in-
terpreting the results is to look for differences in the shapes of the
reduced full wave and the two full waves, which indicate turn-to-
turn insulation failure. Additional test criteria are found in IEEE Std.
C57.98-1993. The impulse tests probably have the highest likelihood
failures among all of the factory tests that are typically performed.
• Partial Discharge Test. This test detects radio-frequency (0.85–1.15
MHz) noise generated from partial discharges within voids in the
insulation. An applied voltage is gradually increased until partial
discharge starts to occur, which is the inception voltage. The voltage
is then decreased until the partial discharge stops, which is the extinc-
tion voltage. The extinction voltage must be less than the operating
voltage of the transformer; otherwise, once partial discharge starts
in the field (due to some voltage transient), it would continue indefi-
nitely and possibly cause damage or failure.

• Insulation Power Factor. Insulation power factor is the ratio of the
power dissipated in the insulation in watts to the apparent power
(volt-amperes) under a sinusoidal voltage. The applied 60 Hz voltage
of this test is generally lower than the operating voltage of the trans-
former. The Doble Test Set is designed specifically to carry out this
test. Portable versions are used to measure the insulation power fac-
tor of transformers in the field. This test usually must be done by a
trained technician. The test results are temperature-corrected to a
reference temperature of 20°C.
• Insulation Resistance. This test applies a high-voltage DC voltage
to one winding at a time with the other windings grounded. The
leakage current is measured and the insulation resistance is calcu-
lated using Ohm’s law. A Megger Test Set is designed specifically
to carry out this test, and its meter is calibrated in megohms in order
that the calculation may be avoided. The Megger is a portable instru-
ment that can easily carried around in the field.
• Noise Measurement. The noise measurement test is carried out while
the transformer is energized at rated voltage with all of the cooling
equipment running. Room geometry can greatly affect the measure-
ments, so it is preferable that the transformer be inside an anechoic
chamber; however, if such a chamber is not available, no acousti-
cally reflecting surface may be within 3 m of the measuring micro-
phone other than the floor or ground. The recording microphones
are positioned in 1 m intervals around the perimeter of the trans-
former, with no fewer than four (4) microphone positions for small
transformers. Sound power levels are measured over a specified band
of frequencies. The sound power levels are converted into decibels
(dB).
• Temperature Rise (Heat Run). The transformer is energized at rated
voltage in order to generate core losses. The windings are connected
to a loading transformer that simultaneously circulates rated currents
through all of the windings in order to develop load losses. Naturally,
the excitation voltage and the applied circulating currents are electri-
cally 90° apart to minimize the KW requirements for this test. None-
theless, a large power transformer can consume up to 1 MW of total
losses and the heat run test is an expensive test to perform. Therefore,
in order to reduce the total expense, heat run tests are normally per-
formed on only one transformer on a purchase order for multiple
transformers, unless the customer chooses to pay for testing addi-
tional units.

• Short-Circuit Test. The short-circuit test is generally reserved for a
sample transformer to verify the design of a core and coil assembly
unless the customer specifies that a short-circuit test be performed
on transformers that are purchased. The customer should be cogni-
zant of the ever-present risk of damaging the transformer during
short-circuit tests. A low-voltage impulse (LVI) current waveform
is applied to the transformer before and after the applications of
short-circuit test. The ‘‘before’’ and ‘‘after’’ oscillograms of the LVI
currents are compared for significant changes in waveshape that
could indicate mechanical damage to the windings.
8.6 FIELD TESTS

In Section 8.2 we discussed the general criteria for good predictive mainte-
nance practices. These same criteria apply to testing. There are a number of
field tests that are considered good predictive maintenance practices and these
should be performed periodically to spot trouble. These tests are also useful
for diagnosing transformer trouble. A Megger test consists of applying a high
DC voltage, usually 1000 V, to each winding with the other windings
grounded and to all windings connected in parallel. The Megger readings are
in megohms and these must be temperature corrected for meaningful results.
The megger readings should be compared to earlier test results to detect any
downward trend in resistance values. The voltage produced by a megger is
high enough to cause insulation breakdown if there are gross faults, but is
really not sensitive enough to detect minor problems in transformers in the
higher voltage classes.
A Doble test is somewhat more sensitive than the Megger test. An AC
voltage, up to 10 kV, is applied to the winding insulation and leakage current
is measured. In addition to the leakage current, the power factor of the insula-
tion is computed. A high power factor indicates lossy insulation, which can
mean imminent trouble. In addition to the winding insulation, the Doble test
is used to measure the power factor of bushing insulation. When testing con-
denser type bushings, the capacitance tap is utilized. The Doble test set is also
used to measure the excitation current through the winding by applying an
AC voltage across the winding. High power factor readings during this test
can indicate flaws in the turn-to-turn insulation.
A TTR test can be used as a diagnostic test in the field. Always connect
the TTR test set clamp leads to a secondary winding of the transformer under
test. Connect the TTR test set clip leads to the primary winding that is on the
same core leg as the secondary winding being tested, observing that the polar-

ity of the red clip test lead matches the polarity of the red clamp test lead.
Set the ratio dials just above zero and give the generator wheel a half turn.
The galvanometer should deflect to the left, indicating the ratio dials need to
be raised. A deflection to the right means that the polarity of the test leads is
incorrect. This can be corrected by swapping the two clip test leads. After the
correct polarity has been verified, slowly turn the generator and make the
appropriate adjustments to the ratio dials in order to keep the galvanometer
needle centered (zero current in the clip test leads). When the ratio dials are
almost set to the right ratio, the generator can be cranked faster to get the
proper voltage indication on the voltmeter (8 V).
If the voltmeter reads low voltage with the ammeter reading high cur-
rent, this is usually an indication of shorted turns, either in the primary or in
the secondary. A zero deflection on the galvanometer at every ratio settings
indicates an open primary winding because no current can flow in the clip
test leads. If the galvanometer deflection is always to the right and cannot be
corrected by reversing the test leads, then this may indicate an open secondary
winding and voltage cannot be generated in the primary winding.
Example 8.1
A repair crew was making a TTR test on a 500–230 kV transformer and the
test leads would not stretch from the HV bushings to the LV bushings, so the
crew moved the TTR Test Set closer to the HV bushings to attach the clip
test leads and connected the clamp to the LV bushings by extending them
using jumper wire. The voltage and current indications on the TTR Test Set
were normal, but the ratio measured 2.5% lower than the theoretical current.
What is wrong?
The clamp test leads are calibrated such that the resistance voltage drop
from the current flow is taken into account by the measurement leads connected
to the clamps. By extending the clamp leads, the crew introduced an additional
resistance voltage drop that reduced the exciting voltage at the LV winding and
hence the voltage induced in the primary. This gave the indication of a low TTR.
In order to perform the test correctly, the clip leads should have been
extended. Since no current flows in the clip leads with the galvanometer read-
ing zero when the correct ratio is dialed in, there is no voltage drop in the
clip lead extensions and the reading will be accurate.
Example 8.2
A three-phase 12470Y/7200-480V station service transformer without a pri-
mary neutral bushing is to be TTR tested. How should the TTR Test Set be

FIGURE 8.3 TTR test set connections for ratio testing an ungrounded Y-∆ trans-
former.
connected since the primary windings cannot be isolated? What is the TTR
test reading for the nominal voltage taps?
To measure the H1-N to X1-X2 winding ratio, connect a jumper wire
between X1 and X3, connect the red clip test lead to H1, the black clip test
lead to H3, the red clamp test lead to X1 and the black clamp test lead to X2,
as shown in Figure 8.3. The jumper wire causes the voltage across both the
X1-X3 winding and the H3-N winding to be zero, so the black clip test lead
is effectively connected to the primary neutral through the shorted H3-N
winding.
The correct ratio is 7200/480 ! 15.000 # 0.075.
Example 8.3
A TTR test is to be performed on a zigzag-∆ transformer, as shown in Figure
8.4. The rated phase-to-phase voltage of the zigzag winding is 12,470 V and
the phase-to-phase voltage of the ∆ secondary is 2,400 V. Show all TTR test
set connections required to test the primary to secondary ratio on the A phase
leg of the primary windings. (Hint: Two separate sets of connections are re-
quired to complete the test. The use of jumper wires is permitted.) What are
the expected readings on the TTR test set?
The jumpers effectively short out each half of the phase-to-neutral wind-
ing. For a zigzag connection, each remaining half of the winding is rated
0.5774 times the phase-to-neutral voltage:
0.5774 $ 7200 V ! 4154.4 V

FIGURE 8.4 TTR test set connections for ratio testing a zigzag-∆ transformer.
The secondary windings are rated 2400 V. The measured turns ratio is 4157/
2400 ! 1.732 :1.
8.7 GAS-IN-OIL ANALYSIS

Various research organizations, such as Westinghouse Electric Corporation,
Analytical Associates, Inc., that did extensive research in the 1970s quickly
led to the widespread use of dissolved gas-in-oil analysis as a predictive main-
tenance tool [4]. There is also an extensive bibliography on this subject found
in IEEE Std. C57.104–1991 [5].
The basic theory is straightforward: Transformer dielectric fluids are
refined from petroleum and are very complex mixtures containing aromatic,
naphthenic, and paraffinic hydrocarbons. At high temperatures, some of these
molecules break down into hydrogen plus small hydrocarbon molecules such

as, methane, ethane, ethylene, acetylene, propane, and propylene. This process
is known as cracking.
The kraft paper materials that are used to insulate transformer windings
are made up of cellulose. At high temperatures, cellulose oxidizes to form
carbon dioxide (CO 2), carbon monoxide (CO) and water (H 2 O). High concen-
trations of CO 2 and or CO are indications of overheated windings.
All of the breakdown products are gases that dissolve readily in trans-
former oil in different concentrations, depending on the specific gas and the
temperatures that produce them. By taking samples of transformer insulating
oil, extracting the dissolved gases and doing a quantitative analysis of the
various gases in the samples through gas chromatography, it is possible to
infer the temperatures at the sites where these gases were produced.
At temperatures below 150°C, transformer oil starts breaking down into
methane (CH 4) and ethane (C 2 H 6). At temperatures above 150°C, ethylene
(C 2 H 4) begins to be produced in large quantities while the concentration of
ethane decreases. At around 600°C, the ethylene production peaks while the
concentration of methane continues to increase. Acetylene (C 2 H 2) production
starts at around 600°C and methane concentration peaks at 1000°C. Hydrogen
(H 2) production is not significant below 700°C and continues to increase along
with acetylene at temperatures above 1400°C.
Therefore, the relative concentrations of the key gases change over a
wide range of temperature. This is basis for the application of dissolved gas-
in-oil analysis for predictive and diagnostic use. An approximate formula uses
the ratio of C 2 H 4 /C 2 H 6 to derive the temperature of oil decomposition between
300°C and 800°C:
C2 H4
T(°C) ! 100 $ % 150
C2 H6
The so-called Rogers ratio method takes the ratios of several key gases
into account to develop a code that is supposed to give an indication of what
is causing the evolution of gas. The codes for the four-ratio method are given
in Table 8.2. A fairly detailed diagnosis of transformer trouble can be derived
from various combinations of codes, shown in Table 8.3.
The diagnoses shown above were derived from empirical observation.
The problem with the four-ratio Rogers code is that a code generated from
the gas concentrations will often not match any of the ‘‘known’’ diagnoses.
So like a rare disease with strange symptoms, many cases of transformer trou-
ble cannot be diagnosed at all using this method. Another method, called the
three-ratio method, sometimes works when the four-ratio method does not.

TABLE 8.2 Four-Ratio Code
Ratio Ratio range Code
CH 4 /H 2 &0.1 5
0.1–1 0
1.0–3.0 1
'3 2
C 2 H 6 /CH 4 (1.0 0
'1.0 1
C 2 H 4 /C 2 H 6 (1.0 0
1.0–3.0 1
)3.0 2
C 2 H 2 /C 2 H 4 (0.5 0
0.5–3.0 1
)3.0 2
In the three-ratio method, the values of A, B, and C are given in Table

8.4 with the corresponding diagnoses for the various combinations given in
Table 8.5. Not only are the ratios of the key gases important, but the total
quantity of dissolved gas and the rate of increase are also important factors
in making a diagnosis. One of the criteria for making a judgment call is the
total combustible gas concentration. The combustible gases include H 2 , CH 4 ,
TABLE 8.3 Diagnosis of Transformer Faults Based on the Four-Ratio Code
CH 4 C2 H6 C2 H4 C2 H2
H2 CH 4 C2 H6 C2 H4 Diagnosis
0 0 0 0 Normal deterioration
5 0 0 0 Partial discharge (corona)
1,2 0 0 0 Slight overheating below 150°C
1,2 1 0 0 Overheating 150°C–200°C
0 1 0 0 Overheating 200°C–300°C
0 0 1 0 General conductor overheating
1 0 1 0 Winding circulating currents
1,2 0 2 0 Core and tank circulating currents, over-
heated joints
0 0 0 1 Flashover without power follow through
0 0 1,2 1,2 Arc with power follow through
0 0 2 2 Continuous sparking to floating potential
5 0 0 1,2 Partial discharge with tracking

TABLE 8.4 Three-Ratio Code
A B C
Ratio C2 H2 CH 4 C2 H4
range C2 H4 H2 C2 H6
(0.1 0 1 0
0.1–1 1 0 0
1–3 1 2 1
)3 2 2 2
C 2 H 4 , C 2 H 6 , C 2 H 2 , which are produced by oil decomposition, and CO, which

is produced by cellulose decomposition. Each utility has a different philosophy
and a different threshold for concern. Table 8.6 gives one set of guidelines
based on good utility practice that is useful for determining the overall health
of a power transformer based on the total concentration of combustible gases.
It is generally accepted that if the rate of combustible gas generation
exceeds 100 ppm per day on a continuing basis, or if the presence of C 2 H 2
exceeds 20 ppm, then consideration should be given to taking the transformer
out of service to perform additional tests and inspection. IEEE Std. C57.104-
1991 Table 3 also provides a set of actions based on the total dissolved com-
bustible gas (TDCG) concentrations as well as the daily rate of TDCG produc-
tion. According to the IEEE Guide, a rate of 30 ppm per day is the threshold
for considering removing the transformer from service.
Oil samples are taken from the bottom drain valve in a sealed syringe to
prevent the dissolved gases from escaping. The samples are sent to a chemical
TABLE 8.5 Diagnosis of Transformer Faults Based on the Three-Ratio Code

A B C Diagnosis
0 0 0 No fault
0 1 0 Partial discharge of low energy
1 1 0 Partial discharge of high energy
1, 2 0 1, 2 Discharge of low energy, arcing
1 0 2 Discharge of high energy, arcing
0 0 1 Thermal fault 150°C, conductor overheating
0 2 0 Thermal fault 150°C–300°C, mild oil overheating
0 2 1 Thermal fault 300°C–700°C, moderate oil overheating
0 2 2 Thermal fault 700°C, severe oil overheating

TABLE 8.6 Recommended Actions Based on Total Combustible Dissolved Gas
in Oil
0 to 500 ppm Represents normal aging. Analyze again in six months.
501–1200 ppm Indicates decomposition may be in excess of normal aging.
Analyze again in three months.
1201–2500 ppm Indicates more than normal decomposition. Analyze again
in one month.
More than 2501 ppm Make weekly analysis to determine rate of generation.
After establishment of rate of generation, contact manu-
facturer concerning future operation.
laboratory where the dissolved gases are extracted from the sample under vac-
uum and analyzed using a gas chromatograph. The results are reported as
ppm dissolved in oil.
Example 8.4
(This example is based on an actual event.)
A generator step-up transformer had been repaired in a transformer shop.
The first gas-in-oil sample was taken approximately 1 month after the trans-
former returned to service and the sample showed over 1000 ppm of total
combustible gas with over 10 ppm of acetylene. Neither the four-ratio nor the
three-ratio code matched any of the diagnoses, but the key gases indicated a
bare-metal hot spot (no cellulose involvement). After 1 week a second oil
sample showed a rate of increase of combustible greater than 200 ppm per
day. A decision was made to shut down the plant and take the transformer
out of service. An inspection quickly revealed the cause: The neutral ends of
the high-voltage Y-connected windings were attached to a neutral wire that
was badly overheated and nearly burned completely through. An investigation
revealed that the neutral conductor was grossly undersized. Apparently, the
designer believed that the ‘‘neutral’’ current was nearly zero because the
phases are balanced, without realizing the conductor between the connections
to the phases carries the full phase currents!
8.8 WATER-IN-OIL ANALYSIS

There is an old expression, ‘‘Oil and water do not mix.’’ Thus, oil is not
usually thought of as having a great affinity for water, and in fact it doesn’t.
However, the kraft paper insulation found in most power transformers has a

tremendous affinity for water. In fact, cellulose is often used as a drying agent
or desiccant. If there is moisture present in the transformer, it will usually
wind up in the kraft paper insulation. Moisture not only weakens the insulating
properties of the kraft paper, it also accelerates the rate of aging. Therefore,
in order to prolong the life of a transformer, moisture must be monitored.
Since samples of the insulation cannot be taken while the transformer
is in service, water-in-oil analysis is used to monitor the moisture content of
the kraft paper as a surrogate. There is a known equilibrium between moisture
concentrations in the kraft paper versus the moisture concentrations in the oil
based on the temperature of the paper and oil. The equilibrium is expressed
by the so-called Piper chart, shown in Figure 8.5 [6].
Notice that as the temperature increases, water is driven from the paper
into the oil. At elevated temperatures the oil is able to dissolve more water
than at lower temperatures. The relationship can be expressed by the following
equation.
T ! 31.52 " 26.605 Ln pct % 17.524 Ln ppm (8.8.1)
where
T ! temperature (°C)
pct ! % water in paper
ppm ! ppm water in oil
When doing a water-in-oil analysis, a syringe sample of oil is taken
from the drain valve. Care must be exercised so that the oil is not exposed
to the atmosphere. (Any exposure to the atmosphere will cause the oil to
FIGURE 8.5 Piper equilibrium chart. (From Ref. 6.)

quickly reach equilibrium with the air. Since ambient air usually contains quite
a bit of moisture, this will generally immediately saturate the oil with water
and produce a meaningless analysis.) The oil temperature is recorded at the
time the sample is taken and the sample is then sent to a chemical laboratory
to analyze the ppm water in oil. From the ppm in the oil sample and the
temperature of the oil, the Piper chart or Eq. (8.8.1) can be used to get an
approximate indication of the percent moisture in the kraft paper.
Note that the temperature of the oil/paper interface has a significant
effect on the equilibrium moisture concentration, but the temperatures of the
oil and the paper vary depending on location. We would then expect the equi-
librium moisture concentration to vary as well, which it does. Generally, the
insulation near the hottest spot will have less percent moisture than insulation
exposed to cooler oil at the bottom of the transformer. An ‘‘average’’ value
of the percent moisture concentration could be calculated from an ‘‘average’’
temperature; however, this may result in a misleading assessment of the trans-
former’s state because of the wide variation in moisture concentrations. A
conservative assessment would base the percent moisture on the oil tempera-
ture at the bottom of the tank. According to the Transformer Maintenance
Institute, 2% is the absolute upper limit for acceptability for percent moisture
in kraft paper. Generally, if the percent moisture is less than 1%, the trans-
former is considered ‘‘dry.’’
There is also an equilibrium equation between vapor pressure of water
in air (humidity) and % water in paper.
T ! 40.17 " 22.285 Ln pct % 14.056 Ln vap (8.8.2)
where vap ! vapor pressure, mmHg.

Since the dew point of air is related to the vapor pressure, a dew-point
measurement of the space inside a transformer before oil filling is a very good
indication of the amount of water locked in the paper. This will determine
whether oil filling should proceed or further drying is necessary.
Example 8.5
An oil sample is taken in an open jar from a transformer with a top oil tempera-
ture of 70°C at an ambient temperature of 25°C and 80% relative humidity.
The oil sample is analyzed and it is found that there is 32.5 ppm water in oil.
Using a piper chart, it is determined that there was 2.33% water in the paper,
which is unacceptable. In reality, however, it was the air that produced the
32.5 ppm water in oil because this is the equilibrium ppm at 25°C and 80%
relative humidity.

8.9 DRYING TRANSFORMERS
If it has been determined that a transformer has an excessive moisture content,
either through water-in-oil analysis or dew-point analysis, the transformer
should be dried out. Otherwise, the presence of moisture in the kraft paper will
definitely shorten the life due to chemical decomposition through oxidation of
the cellulose.
Drying out a transformer can be accomplished by untanking the core
and coil assembly and drying it in an oven, but this would be both expensive
and inconvenient. Fortunately, there are methods that can be applied in the
field that are very effective in drying out a transformer.
A simple hot oil flush is one method, although it is fairly slow. Oil is
pumped through a filter press, which contains paper filter elements, and then
heated and sprayed onto the core and coils. The hot oil has a greater affinity
for moisture than cold oil and will pick up some moisture from the core and
coil insulation. Running the oil through a filter press allows the filter elements
to remove some of the moisture in the oil. Cooling the oil before it goes
through the filter press will enhance the removal of moisture from the oil.
A better method is to spray hot oil into the transformer under vacuum.
The combination of the heat from the hot oil and the vacuum will cause the
moisture in the insulation to ‘‘flash off’’ and dry the transformer. A cold trap
can enhance the action of a mechanical vacuum pump. Once the mechanical
pump removes all the air from the transformer tank, the only gas left in this
space is H 2 O. A cold trap using a dry ice and acetone jacket will instantly freeze
any water vapor with the low-temperature ice having a very low vapor pressure.
The cold trap thus acts like an auxiliary vacuum pump. The ice provides a direct
measurement of the amount of moisture removed from the cellulose.
8.10 OIL DIELECTRIC TEST

Another predictive maintenance activity is periodic performance of oil dielec-
tric testing. An oil sample is taken and placed in a standard test cup with flat
electrodes. The electrodes are separated by a calibrated distance (ASTM D877
Method). An increasing 60 Hz AC voltage is applied to the electrodes until
the oil ‘‘breaks down,’’ tripping out the test set. The test cup is flushed out
and the test is repeated a number times with oil from the same sample. An
average value of the breakdown voltage is determined from these tests. Gener-
ally, the oil is satisfactory if the average breakdown voltage is 30 kV or higher.
Oil can lose insulating properties from excessive moisture, acids, sludge,
and other contaminants. A dielectric test can quickly determine whether or
not the oil is suitable for use as an insulating fluid in a transformer without
performing extensive chemical tests on the oil.

8.11 RELIABILITY CALCULATIONS
Equipment failures do occur even with the best equipment designs available
and the using the best utility practices. In order to operate a power system
reliably, transformer failures must be anticipated and planned for by including
a certain number redundant or spare transformers to the in-service transform-
ers. Allocating a single spare for each transformer size, based on the determin-
istic approach of a single failure, is clearly inadequate because of the long
lead times associated with procuring a replacement transformer. Multiple fail-
ures within the periods defined by these lead times are a distinct possibility,
so that more than one spare for each transformer size may be necessary. The
question is, ‘‘How many?’’ This question is answered in the remaining sec-
tions of this chapter.
8.12 THE CHI-SQUARED DISTRIBUTION

The first order of business is to determine the failure rate λ, expressed as
failures per unit-year in service. This can be accomplished by observing a
population of transformers over time. Since utility companies have rather large
transformer populations that have been in service for many years, this is simply
a matter of keeping good records of when each transformer goes into service,
when it is removed from service, and when it fails. The simplest way to calcu-
late λ is to divide the total number of failures in the population f by the total
number of transformer years in-service T.
f
λ! (8.12.1)
T
Since the number of failures for a given population is rather small (we
hope), there is always some uncertainty as to whether the failure rate calculated
by Eq. (8.12.1) is truly representative of the population. A better estimate of
λ is obtained from the chi-squared probability distribution, symbolized by
χ 2n,1"α . The parameter n is the number of degrees of freedom, and the parameter
α is some confidence limit. The number of degrees of freedom is equal to 2
times the number of failures that were observed in the population. The confi-
dence limit is equal to the probability that the true value of λ will be bounded
by the calculated value.
χ 22f,1"α
λ! (8.12.2)
2T
Values of the chi-squared distribution for various degrees of freedom and proba-
bility values are given in Table 8.7. The probability values are equal to 1 " α.

TABLE 8.7 Chi-Squared Distribution Values
Probability/
Degrees of
Freedom 0.01 0.05 0.1 0.2 0.4 0.5 0.6 0.8 0.9 0.95 0.99
1 6.6349 3.8415 2.7055 1.6424 0.7083 0.4549 0.2750 0.0642 0.0158 0.0039 0.0002
2 9.2104 5.9915 4.6052 3.2189 1.8326 1.3863 1.0217 0.4463 0.2107 0.1026 0.0201
3 11.3449 7.8147 6.2514 4.6416 2.9462 2.3660 1.8692 1.0052 0.5844 0.3518 0.1148
4 13.2767 9.4877 7.7794 5.9886 4.0446 3.3567 2.7528 1.6488 1.0636 0.7107 0.2971
5 15.0863 11.0705 9.2363 7.2893 5.1319 4.3515 3.6555 2.3425 1.6103 1.1455 0.5543
6 16.8119 12.5916 10.6446 8.5581 6.2108 5.3481 4.5702 3.0701 2.2041 1.6354 0.8721
7 18.4753 14.0671 12.0170 9.8032 7.2832 6.3458 5.4932 3.8223 2.8331 2.1673 1.2390
8 20.0902 15.5073 13.3616 11.0301 8.3505 7.3441 6.4226 4.5936 3.4895 2.7326 1.6465
9 21.6660 16.9190 14.6837 12.2421 9.4136 8.3428 7.3570 5.3801 4.1682 3.3251 2.0879
10 23.2093 18.3070 15.9872 13.4420 10.4732 9.3418 8.2955 6.1791 4.8652 3.9403 2.5582
11 24.7250 19.6752 17.2750 14.6314 11.5298 10.3410 9.2373 6.9887 5.5778 4.5748 3.0535
12 26.2170 21.0261 18.5493 15.8120 12.5838 11.3403 10.1820 7.8073 6.3038 5.2260 3.5706
13 27.6882 22.3620 19.8119 16.9848 13.6356 12.3398 11.1291 8.6339 7.0415 5.8919 4.1069
14 29.1412 23.6848 21.0641 18.1508 14.6853 13.3393 12.0785 9.4673 7.7895 6.5706 4.6604
15 30.5780 24.9958 22.3071 19.3107 15.7332 14.3389 13.0298 10.3070 8.5468 7.2609 5.2294
16 31.9999 26.2962 23.5418 20.4651 16.7795 15.3385 13.9827 11.1521 9.3122 7.9616 5.8122
17 33.4087 27.5871 24.7690 21.6146 17.8244 16.3382 14.9373 12.0023 10.0852 8.6718 6.4077
18 34.8052 28.8693 25.9894 22.7595 18.8679 17.3379 15.8932 12.8570 10.8649 9.3904 7.0149
19 36.1908 30.1435 27.2036 23.9004 19.9102 18.3376 16.8504 13.7158 11.6509 10.1170 7.6327
20 37.5663 31.4104 28.4120 25.0375 20.9514 19.3374 17.8088 14.5784 12.4426 10.8508 8.2604
21 38.9322 32.6706 29.6151 26.1711 21.9915 20.3372 18.7683 15.4446 13.2396 11.5913 8.8972
22 40.2894 33.9245 30.8133 27.3015 23.0307 21.3370 19.7288 16.3140 14.0415 12.3380 9.5425
23 41.6383 35.1725 32.0069 28.4288 24.0689 22.3369 20.6902 17.1865 14.8480 13.0905 10.1957
24 42.9798 36.4150 33.1962 29.5533 25.1064 23.3367 21.6525 18.0618 15.6587 13.8484 10.8563
25 44.3140 37.6525 34.3816 30.6752 26.1430 24.3366 22.6156 18.9397 16.4734 14.6114 11.5240
26 45.6416 38.8851 35.5632 31.7946 27.1789 25.3365 23.5794 19.8202 17.2919 15.3792 12.1982
27 46.9628 40.1133 36.7412 32.9117 28.2141 26.3363 24.5440 20.7030 18.1139 16.1514 12.8785
28 48.2782 41.3372 37.9159 34.0266 29.2486 27.3362 25.5092 21.5880 18.9392 16.9279 13.5647
29 49.5878 42.5569 39.0875 35.1394 30.2825 28.3361 26.4751 22.4751 19.7677 17.7084 14.2564
30 50.8922 43.7730 40.2560 36.2502 31.3159 29.3360 27.4416 23.3641 20.5992 18.4927 14.9535
Example 8.6
A population of transformers had three observed failures over a total of 750
transformer-years in service. What is the failure rate within a 95% confidence
limit?
α ! 0.95
2T ! 2 $ 750 years ! 1500 years
2f ! 2 $ 3 failures ! 6
From Table 8.7,
χ 22f,1"α ! χ 26,0.05 ! 12.592
From Eq. (8.12.2),
12.592
λ! ! 0.0084 failures per transformer year
1500
Based on a 95% confidence limit, the true value of λ will not exceed 0.0084
failures per transformer year.
8.13 THE POISSON DISTRIBUTION

The probability that a certain number of failures n will occur within a certain
time period is given by the Poisson distribution if the failures occur randomly
and the failed units are replaced. If every failed transformer is replaced by a
new unit, it can be shown that the population will eventually reach a static
age distribution as the replacement process continues over a long time and
once a static age distribution is reached, the failure rate of the population
remains constant [7].
The Poisson distribution is defined by a single parameter µ, which is
the mean value of all possible values of n ' 0.
e "µ µ n
P(n) ! (8.13.1)
n!
For a population of transformers undergoing failures and replacements, µ is
equal to the mean number of failures occurring within some specific time
interval and P(n) is the probability that exactly n failures actually do occur
within that time interval.
Let M equal the number of in-service transformers and let mttr equal
the mean time to replace a failed transformer. For a population of transformers

having a static age distribution and a failure rate λ, the mean number of trans-
formers that fail during the interval mttr is given by
µ ! M $ λ $ mttr (8.13.2)
The number of transformers that fail within the period mttr is equal to the
number of transformers that exist in the under-repair status. Since the probabil-
ity of exactly n transformers failing within the period mttr is determined by
the Poisson distribution, the probability of exactly n units existing in the under-
repair status at any given time is equal to P r (n), where
e "µ r µ nr
P r (n) ! (8.13.3)
n!
where µ r ! the mean number of transformers under repair. Note that since
the mean number of transformers under repair is equal to the number of trans-
formers that fail during the period mttr, it follows that µ r is given by Eq.
(8.13.2).
If there are N spare transformers assigned to the in-service population,
the probability that all N units are depleted, P u , is equal to the probability that
n ' N.
P u ! P r (n ' N ) ! 1 " P r (n ( N ) (8.13.4)
N"1
e "µr µ nr
Pu ! 1 " !n!0
n!
(8.13.5)
Let MTBF u equal the mean time between transformer failures in the population
when all of the spares have been depleted. This is equal to the mean time
between in-service transformer unavailabilities.
1
MTBF u ! (8.13.5)
M $ λ $P u
Example 8.7
There are 100 transformers of a certain type in service, which have a failure
rate of 0.015 failures per transformer year in service. The mean time to repair
a failed transformer or procure a new transformer is 6 months (0.5 year). How
many spare transformers need to be allocated in order that the mean time
between transformer unavailabilities is greater than 50 years?
From Eq. (8.13.2),
µ r ! 100 $ 0.015 $ 0.5 ! 0.75 units under repair

From Eq. (8.13.5),
1
MTBF u ! ) 50 years
M $ λ $ Pu
Solving for P u ,
1 1
Pu ( ! ! 0.0133
M $ λ $ 50 100 $ 0.015 $ 50
Using Eq. (8.13.5) to calculate P u as a function of N with µ r ! 0.75,
the following tabulation results.
N ! 0: P u ! 1.000 ) 0.0133
N ! 1: P u ! 0.528 ) 0.0133
N ! 2: P u ! 0.173 ) 0.0133
N ! 3: P u ! 0.041 ) 0.0133
N ! 4: P u ! 0.007 ( 0.0133
N ! 4 spare transformers is the minimum number that satisfies the condition
P u ( 0.0133 and MTBF u ) 50 years.
8.14 STATISTICAL ECONOMICS

We are often faced with a decision to purchase a new transformer among
different brands having different initial costs and different failure rates. Occa-
sionally, we must decide whether to purchase a transformer whether to pur-
chase an extended warranty for a new transformer or take our chances of
having a failure. An economic decision can be made on the basis of failure
statistics, hence the term statistical economics.
Suppose a particular type of transformer has a known failure rate λ. The
probability that a unit fails between a time t and t % dt in the future is given
by the following equation:
dP(t) ! e "λt λ dt (8.14.1)
Let C(0) equal today’s cost to repair or replace a failed transformer, and
let C(t) equal the cost to repair or replace a failed transformer at t years in
the future.
C(t) ! C(0)e xt (8.14.2)
where x ! inflation rate per year. The present-worth value of C(t), based on
an inflation rate i is given by
C P (t) ! C(t)e"it ! C(0) e (x"i) t (8.14.3)

The incremental expected present-worth cost of repair for a failure that occurs
between t and t % dt is equal to C P (t) times the probability that this failure
actually occurs.
dC P (t) ! dP(t) $ C P (t) ! C(0) λe "λt e "(i"x)t (8.14.4)

dC P (t) ! C(0) λe "(λ%i"x)t
(8.14.5)
Normally, the transformer manufacturer provides a standard warranty

for W years at no extra charge. Suppose L is the nominal life of the transformer.
The expected present-worth cost to replace this transformer over the out-of-
warranty life of the transformer is found by integrating dC P (t) from t ! W
to t ! L.
L
C P ! C(0) "W
λe "(λ%i"x)t dt (8.14.6)
C(0)λ
CP ! (e "W(λ%i"x) " e "L(λ%i"x)) (8.14.7)
λ%i"x
Manufacturers often offer extended warranties to cover transformer fail-

ures that occur beyond the term of the standard warranty. Purchasing an ex-
tended warranty is justified if the price paid is less than the expected cost of
a transformer failure that occurs between the time the standard warranty
expires and the time the extended warranty expires. If the failure occurs before
or after this period, the extended warranty is worthless. The price breakpoint
can be found from Eq. (8.14.7) by setting L ! the extended warranty expira-
tion.
Example 8.8
Two brands of transformers are evaluated on an economic basis. Brand X has
a purchase price of $50,000 with a 2-year warranty. Based on past perfor-
mance, brand X is expected to have a failure rate of 0.01 per transformer year
in-service. Brand Y has a purchase price of $48,000 with a 1 year warranty.
Based on past performance, brand Y is expected to have a failure rate of 0.015
per transformer year in-service. Clearly, brand X is more reliable and has a
better warranty, but is purchasing brand X justified? Assume an inflation rate
of 0.04 per year and an interest rate of 0.09 per year, and use a 20-year life.
For brand X, λ ! 0.01, C(0) ! $50,000.
λ % i " x ! 0.01 % 0.09 " 0.04 ! 0.06 per year

Using Eq. (8.14.7) for W ! 2 years and L ! 20 years,
$50,000 $ 0.01
CP ! $ (e " 2$(0.06) " e "20$(0.06)) ! $4881
0.06
For brand Y, λ ! 0.015, C(0) ! $48,000.
λ % i " x ! 0.015 % 0.09 " 0.04 ! 0.065 per year
Using Eq. (8.14.7) for W ! 1 year and L ! 20 years,
$48,000 $ 0.01
CP ! $ (e "1$(0.06) " e "20$(0.06)) ! $7361
0.06
The $2000 difference in the initial purchase price is more than offset by the
difference in expected out-of-warranty replacement costs reflected in the val-
ues of C P for brands X and Y calculated above. Therefore, brand Y is the
preferred choice.
Example 8.9
A new transformer is purchased for $100,000. The manufacturer gives a stan-
dard 1 year warranty free of charge but also offers an extended warranty
through 4 years for an added price of $4000. Based on previous experience,
the failure rate of this unit is expected to be 0.7% during the first 10 years in
service. Assuming an inflation rate of 5% per year and an interest rate of 10%
per year, should the extended warranty be purchased from the manufacturer?
λ % i " x ! 0.007 % 0.10 " 0.05 ! 0.057 per year
Using Eq. (8.14.7) with W ! 1 and L ! 4,
$100,000 $ 0.007 "1$(0.057)
CP ! (e " e "4$(0.057)) ! $1823
0.057
The expected present worth of the extended warranty is $1823, whereas its
price is $4000; therefore, the extended warranty is overpriced and it should
not be purchased.
REFERENCES
1. Power Transformers: Acceptance, O&M, Tests, Inspections. Distribution Depart-
ment Instructions DDI S-110. Pennsylvania Power & Light Company, Allentown,
PA, 1997.

2. IEEE Std. C57.12.90-1999. IEEE Standard Test Code for Liquid-Immersed Distri-
bution, Power, and Regulating Transformers. Institute of Electrical and Electronics
Engineers, Inc., New York, 1999.
Immersed Distribution, Power, and Regulating Transformers. Institute of Electrical
and Electronics Engineers, Inc., New York, 2000, pp. 44–48.
4. F. Jakob and T. J. Haupert. Dissolved Gas Analysis, DGA. A Preventative Mainte-
nance Tool. Training handout by Analytical Associates, Inc.
5. IEEE Std. C57.104-1991. IEEE Guide for the Interpretation of Gases Generated
in Oil-Immersed Transformers. Institute of Electrical and Electronics Engineers,
Inc., New York, 1991, pp. 9–27.)
6. S. D. Myers, J. J. Kelley, and R. H. Parrish. A Guide to Transformer Maintenance.
S. D. Myers, Inc., Akron, OH, 1988, p. 257.
7. J. J. Winders, Jr. System Reliability Optimization Through Statistical Economics.
Sixteenth Inter-RAM Conference for the Electric Power Industry Proceedings.
Monterey, CA, 1989, pp. 100–104.

Power Transformers Principles and Application

Uploaded by

Copyright:

Available Formats

Power Transformers Principles and Application

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Power Transformers Principles and Application

Uploaded by

Copyright:

Available Formats

Power

John J. Winders, Jr.

Marcel Dekker, Inc. New York • Basel

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

This book is printed on acid-free paper.

Eastern Hemisphere Distribution

World Wide Web

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

Current printing (last digit):

PRINTED IN THE UNITED STATES OF AMERICA

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

John J. Winders, Jr.

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

Series Introduction H. Lee Willis

1 Basic Transformer Theory

1.1 Definition of a Transformer

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

2 Two-Winding Transformer Connections

3 Transformer Impedance and Losses

3.1 Leakage Flux and Leakage Reactance

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

4 Autotransformers and Three-Winding Transformers

4.1 Autotransformer Connections

5 Short Circuits, Inrush Currents, and Other Phenomena

5.1 Effects of Short Circuits on Transformers

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

7 Reading and Applying Nameplate Information

7.1 Minimum Nameplate Requirements

8 Maintenance, Testing, Troubleshooting, and Reliability

8.1 Good Utility Practices

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

1.1 DEFINITION OF A TRANSFORMER

1.2 MAGNETIC UNITS AND CONVERSION

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

The next magnetic quantity is flux, represented by the Greek letter φ.

The magnetic flux density B is the concentration of magnetic of lines

The magnetic field intensity H is the distribution of MMF along a mag-

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

where µ 0 is the vacuum permeability ! 4π # 10 "7 N/A 2.

Therefore, the magnetic field intensity is inversely proportional to the distance

FIGURE 1.1 B field surrounding a straight cylindrical conductor carrying a current i.

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

1.4 MAGNETIC INDUCTION

FIGURE 1.2 Voltage induced in a loop surrounding a time-varying B field.

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

FIGURE 1.3 Voltage induced in a conductor.

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

conductor is linked to the secondary conductor. Therefore, the efficiency of

1.6 THE MAGNETIC CIRCUIT

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

Consider the magnetic circuit shown in Figure 1.5 consisting of a coil

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

FIGURE 1.6 Magnetic circuit with an air gap.

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.

Copyright © 2002 by Marcel Dekker, Inc. All Rights Reserved.