GETTING STARTED GUIDE

Cisco Aironet 700 Series Access Points

June 2013

1 About this Guide

2 Introduction to the Access Point
3 Safety Instructions
4 Unpacking
5 Configurations
6 Access Point Ports and Connectors
7 Configuring the Access Point
8 Mounting the Access Point
9 Deploying the Access Point on the Wireless Network
10 Troubleshooting
11 Declarations of Conformity and Regulatory Information
12 Configuring DHCP Option 43 and DHCP Option 60
13 Access Point Specifications
1 About this Guide
This Guide provides instructions on how to install and configure your Cisco Aironet 700 Series Access Point. The 700 Series
Access Point is referred to as the 700 series or the access point in this document.

2 Introduction to the Access Point

The 700 series supports high-performing two spatial stream rates over a deployable distance with high reliability when serving
clients. The 700 series provides high reliability and overall wireless performance.
The 700 series offers dual-band radios (2.4 GHz and 5 GHz) with integrated internal antennas. The access point supports full
inter-operability with leading 802.11n clients.
The 700 series access point is available in the controller-based configuration and supports:
• Simultaneous dual-band (2.4 GHz/5 GHz) radios
• Integrated antennas on 702I access point models (AIR-CAP702I-x-K9)

Note The ‘x’ in the model numbers represents the regulatory domain. Refer to “Regulatory Domains” section on page 4
for a list of supported regulatory domains.

The features of the 700 series are:

• Processing sub-systems (including CPUs and memory) and radio hardware which supports:
– Unified
– FlexConnect
– Monitor-mode

Note Enhanced Local Mode (ELM) is not supported.

• The following processor features:

– 128 MB NAND flash size
– 1 MB NOR flash size
– 128 MB DDR2 memory bus, x32
• 2.4 GHz and 5 GHz 802.11n radios with the following features:
– 802.11n standard compliant
– A-MPDU TX
– HT Duplicate Mode
– 2TX x 2RX
– 2-spatial streams, 300 Mbps PHY rate
– Maximal ratio combining (MRC)
– Cyclic Shift Diversity (CSD)
– MCS0-MCS15; Short or Long Guard Intervals
– DFS for UNII-2 and UNII-2 Extended channels, including 0.5us radar pulse detection

3 Safety Instructions
Translated versions of the following safety warnings are provided in the translated safety warnings document that is shipped
with your access point. The translated warnings are also in the Translated Safety Warnings for Cisco Aironet Access Points,
which is available on Cisco.com.

2
Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any
equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for
preventing accidents. Use the statement number provided at the end of each warning to locate its translation in
the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Warning Read the installation instructions before you connect the system to its power source. Statement 1004

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the
protective device is rated not greater than:
20A. Statement 1005

Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless
the device has been modified to be especially qualified for such use. Statement 245B

Warning In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9
inches (20 cm) or more from the body of all persons.
Statement 332

Caution The fasteners you use to mount an access point on a ceiling must be capable of maintaining a minimum pullout
force of 20 lbs (9 kg) and must use all 4 holes on the mounting bracket.

Caution This product and all interconnected equipment must be installed indoors within the same building, including the
associated LAN connections as defined by Environment A of the IEEE 802.af Standard.

Note The access point is suitable for use in environmental air space in accordance with section 300.22.C of the National
Electrical Code and sections 2-128, 12-010(3), and 12-100 of the Canadian Electrical Code, Part 1, C22.1. You should
not install the power supply or power injector in air handling spaces.

Note Use only with listed ITE equipment.

3
4 Unpacking
To unpack the access point, follow these steps:

Step 1 Unpack and remove the access point and the accessory kit from the shipping box.
Step 2 Return any packing material to the shipping container and save it for future use.
Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact your Cisco representative
or reseller for instructions.
– The access point
– Mounting bracket
– Adjustable ceiling-rail clip (if selected when the access point was ordered)

5 Configurations
The 700 series access point contains two simultaneous dual-band radios, the 2.4-GHz and 5-GHz 802.11n MIMO radios, in a
controller-based mode.
The 700 series access point configuration is AIR-CAP702I-x-K9—two 2.4-GHz/5-GHz dual-band radios, with integrated
single-band antennas.
For information on the regulatory domains (shown as “x” in the model numbers) see “Regulatory Domains” section on page 4.

Internal Antennas
The 702I model access points are configured with four single-band, inverted-F antennas (two 2.4-GHz and two 5-GHz). The
four antennas, deployed inside the access point, are evenly spaced inside the top housing. The basic features are as follows:
• Single-band, inverted-F antennas.
• Antenna elements integrated into 702I access point top housing.
• Peak gains are approximately 3 dBi in the 2.4-GHz band and 5 dBi in the 5-GHz band.

Regulatory Domains
The 700 series supports the following regulatory domains (shown as “x” in the model numbers):
• -A, -C, -E, -I, -K, -N, -Q, -R, -S, -T, -Z

Countries Supported
Click this URL to browse to a list of countries and regulatory domains supported by the 700:
www.cisco.com/go/aironet/compliance

6 Access Point Ports and Connectors

The 702I model access points have integrated antennas and do not have external connectors on the top of the unit; however,
they do have the LED indicator on top of the unit, as shown in Figure 1.

4
Figure 1 Access Point LED Indicator (top)

347756

1 LED indicator

The ports and connections on the side of the access point are shown in Figure 2.

5
Figure 2 Access Point Ports and Connections (bottom)

1 2 3 4

347755

5 5 6

1 Mode button 4 AC power connector

2 Ethernet port 5 Mounting bracket pins
3 Console port 6 Security hasp

7 Configuring the Access Point

This section describes how to connect the access point to a wireless LAN controller. Because the configuration process takes
place on the controller, see the Cisco Wireless LAN Controller Configuration Guide for additional information. This guide is
available on Cisco.com.

6
The Controller Discovery Process
The access point uses standard Control and Provisioning of Wireless Access Points Protocol (CAPWAP) to communicate
between the controller and other wireless access points on the network. CAPWAP is a standard, interoperable protocol which
enables an access controller to manage a collection of wireless termination points. The discovery process using CAPWAP is
identical to the Lightweight Access Point Protocol (LWAPP) used with previous Cisco Aironet access points. LWAPP-enabled
access points are compatible with CAPWAP, and conversion to a CAPWAP controller is seamless. Deployments can combine
CAPWAP and LWAPP software on the controllers.
The functionality provided by the controller does not change except for customers who have Layer 2 deployments, which
CAPWAP does not support.
In a CAPWAP environment, a wireless access point discovers a controller by using CAPWAP discovery mechanisms and then
sends it a CAPWAP join request. The controller sends the access point a CAPWAP join response allowing the access point to
join the controller. When the access point joins the controller, the controller manages its configuration, firmware, control
transactions, and data transactions.

Note For additional information about the discovery process and CAPWAP, see the Cisco Wireless LAN Controller Software
Configuration Guide. This document is available on Cisco.com.

Note CAPWAP support is provided in controller software release 5.2 or later. However, your controller must be running
release 7.5.x.x or later to support 700 series access points.

Note You cannot edit or query any access point using the controller CLI if the name of the access point contains a space.

Note Make sure that the controller is set to the current time. If the controller is set to a time that has already occurred, the
access point might not join the controller because its certificate may not be valid for that time.

Access points must discovered a controller before they can become an active part of the network. The access point supports
these controller discovery processes:
• Layer 3 CAPWAP discovery—The access point performs a local broadcast (255.255.255.255) discovery request to find any
contollers on the same subnet/vlan. The request can be forwarded to other networks by the IP helper featuer that is present
on switches and router.
• Locally stored controller IP address discovery—If the access point was previously joined to a controller, the IP addresses of
the primary, secondary, and tertiary controllers are stored in the access point’s non-volatile memory. This process of storing
controller IP addresses on an access point for later deployment is called priming the access point. For more information
about priming, see the “Performing a Pre-Installation Configuration” section on page 8.
• DHCP server discovery—This feature uses DHCP option 43 to provide controller IP addresses to the access points. Cisco
switches support a DHCP server option that is typically used for this capability. For more information about DHCP option
43, see the “Configuring DHCP Option 43 and DHCP Option 60” section on page 23.
• DNS discovery—The access point can discover controllers through your domain name server (DNS). For the access point
to do so, you must configure your DNS to return controller IP addresses in response to
CISCO-CAPWAP-CONTROLLER.localdomain, where localdomain is the access point domain name. Configuring the
CISCO-CAPWAP-CONTROLLER provides backwards compatibility in an existing customer deployment. When an access
point receives an IP address and DNS information from a DHCP server, it contacts the DNS to resolve
CISCO-CAPWAP-CONTROLLER.localdomain. When the DNS sends a list of controller IP addresses, the access point
sends discovery requests to the controllers.

7
Preparing the Access Point
Before you mount and deploy your access point, we recommend that you perform a site survey (or use the site planning tool) to
determine the best location to install your access point.
You should have the following information about your wireless network available:
• Access point locations.
• Access point mounting options: below a suspended ceiling, on a flat horizontal surface, or on a desktop.

Note You can mount the access point above a suspended ceiling but you must purchase additional mounting hardware:
See “Mounting the Access Point” section on page 10 for additional information.

• Access point power options: power supplied by the recommended external power supply (Cisco AIR-PWR-B), a DC power
supply, PoE from a network device, or a PoE power injector/hub (the Cisco-recommended injector is the AIR-PWRINJ5=),
usually located in a wiring closet.

Note Access points mounted in a building’s environmental airspace must be powered using PoE to comply with safety
regulations.

Cisco recommends that you make a site map showing access point locations so that you can record the device MAC addresses
from each location and return them to the person who is planning or managing your wireless network.

Installation Summary
Installing the access point involves these operations:
• Performing a pre-installation configuration (optional)
• Mounting the access point
• Grounding the access point
• Deploying the access point on the wireless network

Performing a Pre-Installation Configuration

The following procedures ensure that your access point installation and initial operation go as expected. A pre-installation
configuration is also known as priming the access point. This procedure is optional.

Note Performing a pre-installation configuration is an optional procedure. If your network controller is properly configured,
you can install your access point in its final location and connect it to the network from there. See the “Deploying the
Access Point on the Wireless Network” section on page 10 for details.

Pre-Installation Configuration Setup

The pre-installation configuration setup is shown in Figure 3.

8
Figure 3 Pre-Installation Configuration Setup

Controller

Layer 3
devices

Cisco Aironet
access points
272488

To perform pre-installation configuration, perform the following steps:

Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network. Use the CLI, web-browser
interface, or Cisco Prime Infrastructure procedures as described in the appropriate Cisco wireless LAN controller guide.
a. Make sure that access points have Layer 3 connectivity to the Cisco wireless LAN controller Management.
b. Configure the switch to which your access point is attach to. See the Cisco Unified Wireless Network WLAN Controller
Configuration Guide for additional information.
c. Set the Cisco wireless LAN controller as the master so that new access points always join with it.
d. Make sure DHCP is enabled on the network. The access point must receive its IP address through DHCP.
e. CAPWAP UDP ports ( ports 5246 and 5247) must not be blocked in the network.
f. The access point must be able to find the IP address of the controller. This can be accomplished using DHCP, DNS, or
IP subnet broadcast. This guide describes the DHCP method to convey the controller IP address. For other methods,
refer to the product documentation. See also the “Using DHCP Option 43” section on page 11 for more information.
Step 2 Apply power to the access point:
a. The access point is 802.3af (15.4 W) compliant and can be powered by any 802.3af compliant device.

Note The 700 series access point requires a Gigibit Ethernet link to prevent the Ethernet port from becoming a
bottleneck for traffic because wireless traffic speeds exceed transmit speeds of a 10/100 Ethernet port.

b. As the access point attempts to connect to the controller, the LEDs cycle through a green, red, and amber sequence, which
can take up to 5 minutes.

Note If the access point remains in this mode for more than five minutes, the access point is unable to find the Master
Cisco wireless LAN controller. Check the connection between the access point and the Cisco wireless LAN
controller and be sure that they are on the same subnet.

c. If the access point shuts down, check the power source.

d. After the access point finds the Cisco wireless LAN controller, it attempts to download the new operating system code
if the access point code version differs from the Cisco wireless LAN controller code version. While this is happening, the
Status LED blinks amber.

9
 e. If the operating system download is successful, the access point reboots.
Step 3 Configure the access point if required. Use the controller CLI, controller GUI, or Cisco Prime Infrastructure to
customize the access-point-specific 802.11n network settings.
Step 4 If the pre-installation configuration is successful, the Status LED is green indicating normal operation. Disconnect the
access point and mount it at the location at which you intend to deploy it on the wireless network.
Step 5 If your access point does not indicate normal operation, turn it off and repeat the pre-installation configuration.

Note When you are installing a Layer 3 access point on a different subnet than the Cisco wireless LAN controller,
be sure that a DHCP server is reachable from the subnet on which you will be installing the access point, and
that the subnet has a route back to the Cisco wireless LAN controller. Also be sure that the route back to the
Cisco wireless LAN controller has destination UDP ports 5246 and 5247 open for CAPWAP communications.
Ensure that the route back to the primary, secondary, and tertiary wireless LAN controller allows IP packet
fragments. Finally, be sure that if address translation is used, that the access point and the Cisco wireless LAN
controller have a static 1-to-1 NAT to an outside address.

8 Mounting the Access Point

Cisco Aironet 700 series access points can be mounted in several configurations, including on a suspended ceiling, on a hard
ceiling or wall, on an electrical or network box, and above a suspended ceiling. Click this URL to browse to complete access
point mounting instructions:
http://www.cisco.com/en/US/docs/wireless/access_point/mounting/guide/apmount.html

9 Deploying the Access Point on the Wireless Network

After you have mounted the access point, follow these steps to deploy it on the wireless network:

Step 1 Connect and power up the access point.

Step 2 Observe the access point LED (for LED descriptions, see “Checking the Access Point LED” section on page 11).
a. When you power up the access point, it begins a power-up sequence that you can verify by observing the access point
LED. If the power-up sequence is successful, the discovery and join process begins. During this process, the LED blinks
sequentially green, red, and amber. When the access point has joined a controller, the LED chirps green if no clients are
associated or stays green if one or more clients are associated.
b. If the LED is not on, the access point is most likely not receiving power.
c. If the LED blinks sequentially for more than 5 minutes, the access point is unable to find its primary, secondary, and
tertiary Cisco wireless LAN controller. Check the connection between the access point and the Cisco wireless LAN
controller, and be sure the access point and the Cisco wireless LAN controller are either on the same subnet or that the
access point has a route back to its primary, secondary, and tertiary Cisco wireless LAN controller. Also, if the access
point is not on the same subnet as the Cisco wireless LAN controller, be sure that there is a properly configured DHCP
server on the same subnet as the access point. See the “Configuring DHCP Option 43 and DHCP Option 60” section
on page 23 for additional information.
Step 3 Reconfigure the Cisco wireless LAN controller so that it is not the Master.

Note A Master Cisco wireless LAN controller should be used only for configuring access points and not in a working
network.

10
10 Troubleshooting
If you experience difficulty getting your access point installed and running, look for a solution to your problem in this guide or
in additional access point documentation. These, and other documents, are available on Cisco.com.

Guidelines for Using Cisco Aironet Lightweight Access Points

Keep these guidelines in mind when you use 700 series lightweight access points:
• The access point can only communicate with Cisco wireless LAN controllers, such as 2500 series, 5500 series, 7500 series,
8500 series, virtual Wireless LAN Controllers, and WiSM2 controllers.
• The access point does not support Wireless Domain Services (WDS) and cannot communicate with WDS devices. However,
the controller provides functionality equivalent to WDS when the access point joins it.
• CAPWAP does not support Layer 2. The access point must get an IP address and discover the controller using Layer 3,
DHCP, DNS, or IP subnet broadcast.
• The access point console port is enabled for monitoring and debug purposes. All configuration commands are disabled when
the access point is connected to a controller.

Using DHCP Option 43

You can use DHCP Option 43 to provide a list of controller IP addresses to the access points, enabling them to find and join a
controller. For additional information, refer to the “Configuring DHCP Option 43 and DHCP Option 60” section on page 23.

Checking the Access Point LED

The location of the access point status LED is shown in Figure 1.

Note Regarding LED status colors, it is expected that there will be small variations in color intensity and hue from unit to
unit. This is within the normal range of the LED manufacturer’s specifications and is not a defect.

The access point status LED indicates various conditions and are described in Table 1.

Table 1 LED Status Indications

Message Status Message

Type LED Meaning
Boot loader status Blinking green DRAM memory test in progress
sequence DRAM memory test OK
Board initialization in progress
Initializing FLASH file system
FLASH memory test OK
Initializing Ethernet
Ethernet OK
Starting Cisco IOS
Initialization successful
Association status Chirping Green Normal operating condition, but no wireless
client associated
Green Normal operating condition, at least one wireless
client association

11
Table 1 LED Status Indications (continued)

Message Status Message

Type LED Meaning
Operating status Blinking amber Software upgrade in progress
Cycling through green, Discovery/join process in progress
red, and amber
Rapidly cycling Access point location command invoked
through red, green, and
amber
Blinking red Ethernet link not operational
Boot loader warnings Blinking amber Configuration recovery in progress (MODE
button pushed for 2 to 3 seconds)
Red Ethernet failure or image recovery (MODE
button pushed for 20 to 30 seconds)
Blinking green Image recovery in progress (MODE button
released)
Boot loader errors Red DRAM memory test failure
Blinking red and amber FLASH file system failure
Blinking red and off Environment variable failure
Bad MAC address
Ethernet failure during image recovery
Boot environment failure
No Cisco image file
Boot failure
Cisco IOS errors Red Software failure; try disconnecting and
reconnecting unit power
Cycling through red, General warning; insufficient inline power
green, amber, and off

Troubleshooting the Access Point Join Process

Access points can fail to join a controller for many reasons: a RADIUS authorization is pending; self-signed certificates are not
enabled on the controller; the access point’s and controller’s regulatory domains don’t match, and so on.
Controller software enables you to configure the access points to send all CAPWAP-related errors to a syslog server. You do not
need to enable any debug commands on the controller because all of the CAPWAP error messages can be viewed from the syslog
server itself.
The state of the access point is not maintained on the controller until it receives a CAPWAP join request from the access point.
Therefore, it can be difficult to determine why the CAPWAP discovery request from a certain access point was rejected. In order
to troubleshoot such joining problems without enabling CAPWAP debug commands on the controller, the controller collects
information for all access points that send a discovery message to it and maintains information for any access points that have
successfully joined it.
The controller collects all join-related information for each access point that sends a CAPWAP discovery request to the
controller. Collection begins with the first discovery message received from the access point and ends with the last configuration
payload sent from the controller to the access point.

12
An access point sends all syslog messages to IP address 255.255.255.255 by default when any of the following conditions are
met:
• An access point running software release 5.2 or later has been newly deployed.
• An existing access point running software release 5.2 or later has been reset after clearing the configuration.
If any of these conditions are met and the access point has not yet joined a controller, you can also configure a DHCP server to
return a syslog server IP address to the access point using option 7 on the server. The access point then starts sending all syslog
messages to this IP address.
When the access point joins a controller for the first time, the controller sends the global syslog server IP address (the default is
255.255.255.255) to the access point. After that, the access point sends all syslog messages to this IP address until it is
overridden by one of the following scenarios:
• The access point is still connected to the same controller, and the global syslog server IP address configuration on the
controller has been changed using the config ap syslog host global syslog_server_IP_address command. In this case, the
controller sends the new global syslog server IP address to the access point.
• The access point is still connected to the same controller, and a specific syslog server IP address has been configured for the
access point on the controller using the config ap syslog host specific Cisco_AP syslog_server_IP_address command. In this
case, the controller sends the new specific syslog server IP address to the access point.
• The access point is disconnected from the controller and joins another controller. In this case, the new controller sends its
global syslog server IP address to the access point.
• Whenever a new syslog server IP address overrides the existing syslog server IP address, the old address is erased from
persistent storage, and the new address is stored in its place. The access point also starts sending all syslog messages to the
new IP address provided the access point can reach the syslog server IP address.
You can configure the syslog server for access points and view the access point join information only from the controller CLI.
A detailed explanation of the join process is on Cisco.com at the following URL:
http://www.Cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml

11 Declarations of Conformity and Regulatory Information

This section provides declarations of conformity and regulatory information for Cisco Aironet 700 Series Access Points. You
can find additional information at this URL:
www.cisco.com/go/aironet/compliance

Manufacturers Federal Communication Commission Declaration of Conformity

Statement

Models Certification Numbers

AIR-CAP702I-A-K9 LDK102085
AIR-SAP702I-A-K9

13
Manufacturer:
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
This device complies with Part 15 rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This device operates in the 5150-5250MHz and 5470-5725MHz bands and is therefore restricted to indoor operation only per
FCC guidance.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used
in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not
occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician.

Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when
using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could
void the user’s authority to operate this device.

Caution Within the 5.15 to 5.25 GHz and 5.47-5.725 GHz bands, this device is restricted to indoor operations to reduce
any potential for harmful interference to co-channel Mobile Satellite System (MSS) operations.

VCCI Statement for Japan

Warning
This is a Class B product based on the standard of the Voluntary Control
Council for Interference from Information Technology Equipment (VCCI). If this
is used near a radio or television receiver in a domestic environment, it may
cause radio interference. Install and use the equipment according to the
instruction manual.

14
Guidelines for Operating Cisco Aironet Access Points in Japan
This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines
are provided in both Japanese and English.

Japanese Translation

208697
03-6434-6500

English Translation
This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens
and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio
stations) used in factory production lines.
1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are
used in the vicinity.
2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using
the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting
partitions.
3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below.
Contact Number: 03-6434-6500

Statement 371—Power Cable and AC Adapter

15
English Translation
When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any
other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of
UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO.
The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not
limited to CISCO-designated products.

Industry Canada

Canadian Compliance Statement

Models Certification Numbers

AIR-CAP702I-A-K9 2461B-102085
AIR-SAP702I-E-K9

This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.
This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Cisco Aironet Access Points are certified to the requirements of RSS-210. The use of this device in a system operating either
partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations.
For further information, contact your local Industry Canada office.
This device has been designed to operate with antennas having a maximum gain of 5 dBi. Antennas having a gain greater than
5 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (EIRP) is not more than that permitted for successful communication.

French Translation
Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.
Cet appareil respecte les limites prescrites pour les appareils de classe B par Industrie Canada. Son utilisation est soumise aux
deux conditions suivantes :
(1) Cet appareil ne doit pas causer d’interf_rences nuisibles, et
(2) Cet appareil doit accepter toutes les interf_rences, y compris celles susceptibles de perturber le fonctionnement de l’appareil.
Les points d'acc_s Aironet de Cisco sont certifi_s conform_ment aux exigences du CNR-210. L'utilisation de cet appareil dans
un syst_me fonctionnant partiellement ou enti_rement ˆ l'ext_rieur peut n_cessiter l'obtention d'une licence pour le syst_me,
conform_ment ˆ la r_glementation canadienne. Pour plus de renseignements, communiquez avec le bureau local d'Industrie
Canada.
Cet appareil a _t_ con_u pour fonctionner avec une antenne d'un gain maximum de 6 dBi. Il est strictement interdit d'utiliser
des antennes ayant un gain sup_rieur ˆ 6 dBi avec cet appareil. L'antenne doit avoir une imp_dance de 50 ohms.
Afin de r_duire le risque d'interf_rence aux autres utilisateurs, le type d'antenne et son gain doivent _tre choisis de fa_on ˆ ce
que la puissance isotrope rayonn_e _quivalente (p.i.r.e.) ne soit pas sup_rieure au niveau requis pour obtenir une communication
satisfaisante.

16
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Models:
AIR-CAP702I-E-K9
AIR-SAP702I-E-K9

Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical
Directive 93/42/EEC

17
The following standards were applied:
EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1
Health & Safety—EN60950-1: 2005; EN 50385: 2002
Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1
The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed.
This device also conforms to the EMC requirements of the Medical Devices Directive 93/42/EEC.

Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain
frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.

The product carries the CE Mark:

Declaration of Conformity for RF Exposure

This section contains information on compliance with guidelines related to RF exposure.

18
Generic Discussion on RF Exposure
The Cisco products are designed to comply with the following national and international standards on Human Exposure to
Radio Frequencies:
• US 47 Code of Federal Regulations Part 2 Subpart J
• American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers / IEEE C 95.1 (99)
• International Commission on Non Ionizing Radiation Protection (ICNIRP) 98
• Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields in the range from 3kHz
to 300 GHz
• Australia Radiation Protection Standard
To ensure compliance with various national and international Electromagnetic Field (EMF) standards, the system should only
be operated with Cisco approved antennas and accessories.

This Device Meets International Guidelines for Exposure to Radio Waves

The 700 series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves
(radio frequency electromagnetic fields) recommended by international guidelines. The guidelines were developed by an
independent scientific organization (ICNIRP) and include a substantial safety margin designed to ensure the safety of all persons,
regardless of age and health.
As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to
set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance
to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator.

Separation Distance
MPE Distance Limit
2
0.63 mW/cm 20 cm (7.87 inches) 1.00 mW/cm2

The World Health Organization has stated that present scientific information does not indicate the need for any special
precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure then
you can easily do so by reorienting antennas away from the user or placing he antennas at a greater separation distance then
recommended.

This Device Meets FCC Guidelines for Exposure to Radio Waves

The 700 series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves
(radio frequency electromagnetic fields) as referenced in FCC Part 1.1310. The guidelines are based on IEEE ANSI C 95.1 (92)
and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health.
As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to
set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance
to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator.
The device has been tested and found compliant with the applicable regulations as part of the radio certification process.

Separation Distance
MPE Distance Limit
0.63 mW/cm2 20 cm (7.87 inches) 1.00 mW/cm2

The US Food and Drug Administration has stated that present scientific information does not indicate the need for any special
precautions for the use of wireless devices. The FCC recommends that if you are interested in further reducing your exposure
then you can easily do so by reorienting antennas away from the user or placing the antennas at a greater separation distance
then recommended or lowering the transmitter power output.

19
This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves
The 700 series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves
(radio frequency electromagnetic fields) as referenced in Health Canada Safety Code 6. The guidelines include a substantial
safety margin designed into the limit to ensure the safety of all persons, regardless of age and health.
As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to
set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance
to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator.

Separation Distance
MPE Distance Limit
2
0.63 mW/cm 20 cm (7.87 inches) 1.00 mW/cm2

Health Canada states that present scientific information does not indicate the need for any special precautions for the use of
wireless devices. They recommend that if you are interested in further reducing your exposure you can easily do so by reorienting
antennas away from the user, placing the antennas at a greater separation distance than recommended, or lowering the
transmitter power output.

Additional Information on RF Exposure

You can find additional information on the subject at the following links:
• Cisco Systems Spread Spectrum Radios and RF Safety white paper at this URL:
http://www.cisco.com/warp/public/cc/pd/witc/ao340ap/prodlit/rfhr_wi.htm
• FCC Bulletin 56: Questions and Answers about Biological Effects and Potential Hazards of Radio Frequency
Electromagnetic Fields
• FCC Bulletin 65: Evaluating Compliance with the FCC guidelines for Human Exposure to Radio Frequency Electromagnetic
Fields
• FCC Bulletin 65C (01-01): Evaluating Compliance with the FCC guidelines for Human Exposure to Radio Frequency
Electromagnetic Fields: Additional Information for Evaluating Compliance for Mobile and Portable Devices with FCC
limits for Human Exposure to Radio Frequency Emission
You can obtain additional information from the following organizations:
• World Health Organization Internal Commission on Non-Ionizing Radiation Protection at this URL: www.who.int/emf
• United Kingdom, National Radiological Protection Board at this URL: www.nrpb.org.uk
• Cellular Telecommunications Association at this URL: www.wow-com.com
• The Mobile Manufacturers Forum at this URL: www.mmfai.org

Administrative Rules for Cisco Aironet Access Points in Taiwan

This section provides administrative rules for operating Cisco Aironet access points in Taiwan. The rules for all access points
are provided in both Chinese and English.

20
Chinese Translation

English Translation
Administrative Rules for Low-power Radio-Frequency Devices
Article 12
For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users
should not change its frequencies, increase its power or change its original features and functions.
Article 14
The operation of the low-power radio-frequency devices is subject to the conditions that no harmful interference is caused to
aviation safety and authorized radio station; and if interference is caused, the user must stop operating the device immediately
and can't re-operate it until the harmful interference is clear.
The authorized radio station means a radio-communication service operating in accordance with the Communication Act.
The operation of the low-power radio-frequency devices is subject to the interference caused by the operation of an authorized
radio station, by another intentional or unintentional radiator, by industrial, scientific and medical (ISM) equipment, or by an
incidental radiator.

21
Chinese Translation

English Translation
Low-power Radio-frequency Devices Technical Specifications

4.7 Unlicensed National Information Infrastructure

4.7.5 Within the 5.25-5.35 GHz band, U-NII devices will be restricted to indoor operations to
reduce any potential for harmful interference to co-channel MSS operations.

4.7.6 The U-NII devices shall accept any interference from legal communications and shall not
interfere the legal communications. If interference is caused, the user must stop operating
the device immediately and can't re-operate it until the harmful interference is clear.

4.7.7 Manufacturers of U-NII devices are responsible for ensuring frequency stability such that
an emission is maintained within the band of operation under all conditions of normal
operation as specified in the user manual.

22
Operation of Cisco Aironet Access Points in Brazil
This section contains special information for operation of Cisco Aironet access points in Brazil.

Access Point Models

AIR-CAP702I-T-K9
AIR-SAP702I-T-K9

Portuguese Translation
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de
estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.

English Translation
This equipment operates on a secondary basis and consequently must accept harmful interference, including interference from
stations of the same kind. This equipment may not cause harmful interference to systems operating on a primary basis.

Declaration of Conformity Statements

All the Declaration of Conformity statements related to this product can be found at the following location:
http://www.ciscofax.com

12 Configuring DHCP Option 43 and DHCP Option 60

This section contains a DHCP Option 43 configuration example on a Windows 2003 Enterprise DHCP server for use with Cisco
Aironet lightweight access points. For other DHCP server implementations, consult product documentation for configuring
DHCP Option 43. In Option 43, you should use the IP address of the controller management interface.

Note DHCP Option 43 is limited to one access point type per DHCP pool. You must configure a separate DHCP pool for
each access point type.

The 700 series access point uses the type-length-value (TLV) format for DHCP Option 43. DHCP servers must be programmed
to return the option based on the access point’s DHCP Vendor Class Identifier (VCI) string (DHCP Option 60). The VCI string
for the 700 series access point is:
Cisco AP c700

Note If your access point was ordered with the Service Provider Option (AIR-OPT60-DHCP) selected in the ordering tool,
the VCI string for the access point contains ServiceProvider. For example, a 700 with this option will return this VCI
string:
Cisco AP c700-ServiceProvider

The format of the TLV block is listed below:

• Type: 0xf1 (decimal 241)
• Length: Number of controller IP addresses * 4
• Value: List of WLC management interfaces
To configure DHCP Option 43 in the embedded Cisco IOS DHCP server, follow these steps:

Step 1 Enter configuration mode at the Cisco IOS CLI.

23
Step 2 Create the DHCP pool, including the necessary parameters such as default router and name server. A DHCP scope
example is as follows:
ip dhcp pool <pool name>
network <IP Network> <Netmask>
default-router <Default router>
dns-server <DNS Server>

Where:
<pool name> is the name of the DHCP pool, such as AP702
<IP Network> is the network IP address where the controller resides, such as 10.0.15.1
<Netmask> is the subnet mask, such as 255.255.255.0
<Default router> is the IP address of the default router, such as 10.0.0.1
<DNS Server> is the IP address of the DNS server, such as 10.0.10.2

Step 3 Add the option 60 line using the following syntax:

option 60 ascii “VCI string”

For the VCI string, “Cisco AP c702”. The quotation marks must be included.

Step 4 Add the option 43 line using the following syntax:

option 43 hex <hex string>

The hex string is assembled by concatenating the TLV values shown below:
Type + Length + Value
Type is always f1(hex). Length is the number of controller management IP addresses times 4 in hex. Value is the IP
address of the controller listed sequentially in hex.
For example, suppose that there are two controllers with management interface IP addresses, 10.126.126.2 and 10.127.127.2.
The type is f1(hex). The length is 2 * 4 = 8 = 08 (hex). The IP addresses translate to 0a7e7e02 and 0a7f7f02. Assembling the
string then yields f1080a7e7e020a7f7f02. The resulting Cisco IOS command added to the DHCP scope is option 43 hex
f1080a7e7e020a7f7f02.

13 Access Point Specifications

Table 2 lists the technical specifications for 700 series access points.

Table 2 Access Point Specifications

Category Specification
Dimensions without 7 x 7 x 2 in (177.6 x 177.6 x 50.4 mm)
mounting bracket
(LxWxD)
Weight 1.06 lb (0.48 kg)
Operating temperatures 32 to 104 degrees F (0 to 40 degrees C)
Storage temperature –22 to 158 degrees F (–30 to 70 degrees C)
Operating humidity 10% to 90% (noncondensing)
Storage humidity 5% to 95% (noncondensing)
Antennas AP70xI: Integrated
Compliance The 700 series access point complies with UL 2043 for products installed in
a building’s environmental air handling spaces, such as above suspended
ceilings.

24
Table 2 Access Point Specifications (continued)

Category Specification
Safety UL 60950-1
CAN/CSA C22.2 No. 60950-1
IEC 60950-1 with all national deviations
EN 60950-1
UL 2043
EMI and Susceptibility FCC Part 15.107 and 15.109 Class B
ICES-003 Class B (Canada)
EN 301.489
EN 55022 Class B
EN 55024
VCCI Class B
Radio FCC Part 15.247, 15.407
Canada RSS-210
Japan Telec 33, 66, T71
EN 330.328, EN 301.893
FCC Bulletin OET-65C
Industry Canada RSS-102
Maximum power and Maximum power and the channels allowed in your regulatory domain,
channel settings refer to Channels and Maximum Power Settings for Cisco Aironet
Lightweight Access Points. This document is available on Cisco.com.

14 Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see
What’s New in Cisco Product Documentation at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html.
Subscribe to What’s New in Cisco Product Documentation, which lists all new and revised Cisco technical documentation, as an RSS
feed and deliver content directly to your desktop using a reader application. The RSS feeds are a free service.

25
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the
document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
© 2013 Cisco Systems, Inc. All rights reserved.

26