AV Receiver Ampli-Tuner Audio-Vidéo: Owner'S Manual Mode D'Emploi
AV Receiver Ampli-Tuner Audio-Vidéo: Owner'S Manual Mode D'Emploi
AV Receiver Ampli-Tuner Audio-Vidéo: Owner'S Manual Mode D'Emploi
RX-V561
RX-V561
AV Receiver
Ampli-tuner audio-vidéo
OWNER’S MANUAL
MODE D’EMPLOI
Caution-i En
Downloaded from www.Manualslib.com manuals search engine
Important safety instructions
d) If the product does not operate normally by following 24 Outdoor Antenna Grounding – If an outside antenna or
the operating instructions. Adjust only those controls cable system is connected to the product, be sure the antenna
that are covered by the operating instructions as an or cable system is grounded so as to provide some
improper adjustment of other controls may result in protection against voltage surges and built-up static charges.
damage and will often require extensive work by a Article 810 of the National Electrical Code, ANSI/NFPA 70,
qualified technician to restore the product to its normal provides information with regard to proper grounding of the
operation, mast and supporting structure, grounding of the lead-in wire
e) If the product has been dropped or damaged in any to an antenna discharge unit, size of grounding conductors,
way, and location of antenna discharge unit, connection to grounding
f) When the product exhibits a distinct change in perfor- electrodes, and requirements for the grounding electrode.
mance - this indicates a need for service.
20 Replacement Parts – When replacement parts are required, EXAMPLE OF ANTENNA GROUNDING
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
MAST ANTENNA
hazards. LEAD IN
WIRE
21 Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety GROUND
CLAMP
checks to determine that the product is in proper operating
condition.
22 Wall or Ceiling Mounting – The unit should be mounted ANTENNA
DISCHARGE UNIT
to a wall or ceiling only as recommended by the (NEC SECTION 810–20)
manufacturer.
ELECTRIC
23 Heat – The product should be situated away from heat SERVICE
EQUIPMENT
sources such as radiators, heat registers, stoves, or other GROUNDING CONDUCTORS
(NEC SECTION 810–21)
products (including amplifiers) that produce heat.
GROUND CLAMPS
attention to Article 820-40 of the NEC that provides NEC – NATIONAL ELECTRICAL CODE
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
Caution-ii En
Downloaded from www.Manualslib.com manuals search engine
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
Caution-iii En
Downloaded from www.Manualslib.com manuals search engine
Contents
INTRODUCTION
INTRODUCTION ADVANCED OPERATION
Features ................................................................... 2 SET MENU ............................................................46
Getting started ........................................................ 3 Using SET MENU................................................... 47
Quick start guide .................................................... 4 1 SOUND MENU.................................................... 48
Preparation: Check the items ..................................... 4 2 INPUT MENU...................................................... 52
Step 1: Set up your speakers...................................... 5 3 OPTION MENU................................................... 54
Step 2: Connect your DVD player Remote control features........................................56
and other components............................................ 6 Using remote control on the SCENE feature........... 56
PREPARATION
Step 3: Turn on the power Controlling this unit, a TV, or other components........ 57
and press SCENE 1 button .................................... 8 Setting remote control codes ................................... 59
What do you want to do with this unit?..................... 9 Advanced setup......................................................60
OPERATION
Placing speakers....................................................... 11 Specifications .........................................................70
Connecting speakers ................................................ 12 Index .......................................................................71
BASIC
Setting the speaker impedance................................. 13
Information on jacks and cable plugs ...................... 14
Information on HDMI™.......................................... 15
APPENDIX
Connecting video components................................. 16
Connecting audio components................................. 19 (at the end of this manual)
Using the VIDEO AUX jacks on the front panel ........ 20
Connecting the FM and AM antennas ..................... 20 Front panel................................................................i
OPERATION
ADVANCED
Connecting the power cable..................................... 21 Remote control ....................................................... ii
Turning on and off the power .................................. 21 List of remote control codes ................................. iii
Front panel display .................................................. 22
Optimizing the speaker setting
for your listening room .................................... 24
Using AUTO SETUP .............................................. 24
INFORMATION
BASIC OPERATION
ADDITIONAL
Selecting the SCENE templates........................... 28 About this manual
Selecting the desired SCENE template.................... 28 • y indicates a tip for your operation.
Creating your original SCENE templates................ 31 • Some operations can be performed by using either the
Playback ................................................................ 32 buttons on the front panel or the ones on the remote control.
Basic operations....................................................... 32 In case the button names differ between the front panel and
Additional operations............................................... 33 the remote control, the button name on the remote control is
Sound field programs ........................................... 37 given in parentheses.
Sound field program descriptions............................ 37 • This manual is printed prior to production. Design and
FM/AM tuning ...................................................... 40 specifications are subject to change in part as a result of
Automatic tuning ..................................................... 40 improvements, etc. In case of differences between the
APPENDIX
1 En
Downloaded from www.Manualslib.com manuals search engine
Features
Features
Built-in 5-channel power amplifier HDMI (High-Definition Multimedia Interface)
◆ Minimum RMS output power ◆ HDMI interface for standard, enhanced or high-definition
[Front, Center, Surround channels] video (includes 1080p video signal transmission)
100 W (1 kHz, 0.9% THD, 6 Ω)
USB features
SCENE select function ◆ USB port to connect a USB memory device or a USB portable
◆ Preset SCENE templates for various situations audio player
◆ SCENE template customizing capability ◆ MP3, WMA and WAV capability
Yamaha and the Electronic Industries Association’s Consumer Since hearing damage from loud sounds is often
Electronics Group want you to get the most out of your undetectable until it is too late, Yamaha and the
equipment by playing it at a safe level. One that lets the sound Electronic Industries Association’s Consumer
come through loud and clear without annoying blaring or Electronics Group recommend you to avoid
distortion – and, most importantly, without affecting your prolonged exposure from excessive volume levels.
sensitive hearing.
2 En
Downloaded from www.Manualslib.com manuals search engine
Getting started
Getting started
■ Checking the supplied accessories ■ Installing batteries in the remote control
INTRODUCTION
Check that you received all of the following parts.
Remote control Batteries (2) AM loop antenna 1 3
POWER POWER STANDBY POWER
(AAA, R03, UM-4)
TV AV
CD MD/CD-R TUNER
V-AUX USB
SCENE
1 2 3 4
BAND LEVEL
TITLE MENU VOLUME
RETURN
REC
DISPLAY
microphone
FREQ/TEXT EON MODE – PTY SEEK – START
9 0 10 ENT
Notes
• Change all of the batteries if you notice the following condition:
– the operation range of the remote control decreases.
• Do not use an old battery and a new one together.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
• If the remote control is without batteries for more than 2
minutes, or if exhausted batteries remain in the remote control,
the contents of the memory may be cleared. When the memory
is cleared, insert new batteries and set up the remote control
code.
English
3 En
Downloaded from www.Manualslib.com manuals search engine
Quick start guide
☞ P. 8
4 En
Downloaded from www.Manualslib.com manuals search engine
Quick start guide
Place your speakers in the room and connect them to this Front speakers
INTRODUCTION
unit.
ANTENNA SPEAKERS AC OUTLETS
PR S VIDEO
GND
DIGITAL INPUT
PB
FM
R SURROUND L CENTER R FRONT B L
75
OPTICAL UNBAL.
VIDEO
CD 3
DVD 1
R R
COAXIAL
SUBWOOFER R FRONT A L
1 2 3 4
4 Connect the subwoofer cable to the input
jack of the subwoofer and the SUBWOOFER
OUTPUT jack of this unit.
1 Make sure that this unit and the subwoofer are Subwoofer
SUB
WOOFER
Subwoofer cable
English
5 En
Downloaded from www.Manualslib.com manuals search engine
Quick start guide
Step 2: Connect your DVD player 2 Connect the video cable to the composite
and other components video output jack of your DVD player and the
DVD VIDEO jack of this unit.
ANTENNA SPEAKERS AC OUTLETS
DVD
COMPONENT VIDEO
DTV/CBL DVR MONITOR
OUT
DVD
DVD
DTV/CBL
VIDEO
IN
DTV/CBL
DVR OUT
HDMI
MONITOR
AV receiver
OUT OUT
AM
PR S VIDEO
GND
DIGITAL INPUT
PB
FM
R SURROUND L CENTER R FRONT B L
75
OPTICAL UNBAL.
CD 3
Y
MULTI CH INPUT
VIDEO
AUDIO
IN MD/ OUT
OUTPUT
DVD player
FRONT SURROUND CENTER DVD DTV/CBL IN DVR OUT CD (PLAY) CD-R (REC)
DTV/
CBL 2
L L SUB
WOOFER
DVD 1
R R
COAXIAL
SUBWOOFER R FRONT A L
Make sure that this unit and the DVD DVD VIDEO jack
Composite video
player are unplugged from the AC wall output jack Video cable
outlets.
L/MONO R Y PB PR L/MONO R
6 En
Downloaded from www.Manualslib.com manuals search engine
Quick start guide
INTRODUCTION
☞ P. 12
• Connecting a video monitor
☞ P. 16
• Connecting a DVD player
☞ P. 16
• Connecting a DVD recorder
☞ P. 16
• Connecting a cable TV or a satellite tuner
☞ P. 16
AM loop antenna • Connecting a CD player and an MD
recorder
Indoor FM antenna
☞ P. 19
• Connecting a DVD player via analog
multi-channel audio connection
☞ P. 19
• Using the VIDEO AUX jacks on the front
panel
☞ P. 20
• Connecting an outdoor FM/AM antenna
Open the lever Insert Close the lever
☞ P. 20
• Using the USB jack on the front panel
☞ P. 43
y
The wire of the AM loop antenna does not have any polarity and
you can connect either end of the wire to AM and GND terminal.
Note
The shape of the AM and GND terminals may vary depending on
the unit.
7 En
Downloaded from www.Manualslib.com manuals search engine
Quick start guide
Step 3: Turn on the power and 4 Start playback of the desired DVD on your
press SCENE 1 button player.
Check the type of the connected speakers. 5 Rotate 8 VOLUME to adjust the volume.
If the speakers are 6 ohm speakers, set “SP IMP.” to
“6Ω MIN” before using this unit (see page 13).
Note
When you change the input source or sound field program, the
SCENE mode is deactivated, and the indicator on the selected
SCENE button turns off.
Note
To use the “TV Viewing” template, you must connect a
cable TV or a satellite tuner to this unit in advance. See
page 16 for details.
y
The indicator on the selected SCENE button lights up while
this unit is in the SCENE mode.
8 En
Downloaded from www.Manualslib.com manuals search engine
Quick start guide
INTRODUCTION
“Radio Listening”. ■ Customizing the SCENE templates
• Using various SCENE templates
Notes
☞ P. 28
• To use the “Radio Listening” template, you must tune into
the desired radio station in advance. See pages 40 to 42 for • Creating your original SCENE templates
tuning information. ☞ P. 31
• To achieve the best possible reception, orient the
connected AM loop antenna, or adjust the position of the
end of the indoor FM antenna. ■ Using various input sources
y • Basic controls of this unit
If you cannot find the desired situation, you can select and change
☞ P. 32
the assigned SCENE template for the SCENE buttons. See
page 28 for details. • Enjoying FM/AM radio programs
☞ P. 40
■ After using this unit...
• Using your USB portable device with this
unit
Press 1 STANDBY/ON on the front panel to set
this unit to the standby mode. ☞ P. 43
■ Additional features
Automatically turning off this unit
English
☞ P. 36
9 En
Downloaded from www.Manualslib.com manuals search engine
Connections
Connections
Rear panel
1 2 3 4 5 6
PR S VIDEO
GND
DIGITAL INPUT
PB
FM
R SURROUND L CENTER R FRONT B L
75
OPTICAL UNBAL.
Y VIDEO
CD 3
DVD 1
R R
COAXIAL
SUBWOOFER R FRONT A L
7 8 9 0
10 En
Downloaded from www.Manualslib.com manuals search engine
Connections
Placing speakers
The speaker layout below shows the speaker setting we recommend. You can use it to enjoy CINEMA DSP and multi-
channel audio sources.
FL C FR
FR
SW
30˚
FL SR
PREPARATION
C
SL SR SL
60˚
80˚ SR
SL
1.8 m (6 ft)
English
11 En
Downloaded from www.Manualslib.com manuals search engine
Connections
Connecting speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,
this unit cannot reproduce the input sources accurately.
Caution
• Before connecting the speakers, make sure that this unit is turned off (see page 21).
• Do not let the bare speaker wires touch each other or let them touch any metal part of this unit. This could damage
this unit and/or the speakers.
• Use the magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the
speakers away from the monitor.
• If you are to use 6 ohm speakers, be sure to set “SP IMP.” to “6Ω MIN” before using this unit (see page 13).
Note
A speaker cable is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a stripe,
groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the plain cable
to the “–” (black) terminals.
Center speaker
PR S VIDEO
GND
DIGITAL INPUT
PB
FM
R SURROUND L CENTER R FRONT B L
75
OPTICAL UNBAL.
Y VIDEO
CD 3
DVD 1
R R
COAXIAL
SUBWOOFER R FRONT A L
12 En
Downloaded from www.Manualslib.com manuals search engine
Connections
PREPARATION
prevent short circuits.
2 Press and hold 0 TONE CONTROL and
10 mm (3/8”) then press 1 STANDBY/ON to turn on this
unit.
This unit turns on, an the advanced setup menu
appears in the front panel display.
■ Connecting to the SPEAKERS terminals
3 Press A PROGRAM l / h repeatedly to
select “SP IMP.”.
The following display appears in the front panel
2 display.
1 Red: positive (+)
Black: negative (–)
3 SP IMP.- 8 MIN
13 En
Downloaded from www.Manualslib.com manuals search engine
Connections
O V S
L R C Y PB PR
Note
The OSD signal is not output at the DVR OUT (REC) jacks.
14 En
Downloaded from www.Manualslib.com manuals search engine
Connections
Information on HDMI™
Audio signals input at the HDMI jack are not output from any speaker terminals but output from the connected video
monitor.
To enjoy the sound from speakers connected to this unit,
– make an analog or digital connection besides the HDMI connection (see page 16).
– mute the volume of the connected video monitor.
You can play back pictures by connecting your video monitor and video source component to this unit using HDMI
connections.
At that time, audio/video signals output from the connected component (such as DVD player etc.) are output to the
PREPARATION
connected video monitor only when this unit is turned on and set to the input source (DVD or DTV/CBL).
Furthermore, available audio/video signals depend on the specification of the connected video monitor. Refer to the
instruction manual of each connected component.
HDMI
y
• We recommend using an HDMI cable shorter than 5 meters
(16 feet) with the HDMI logo printed on it.
• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect
this unit to other DVI components.
English
15 En
Downloaded from www.Manualslib.com manuals search engine
Connections
PR S VIDEO PR S VIDEO
PB PB
OPTICAL OPTICAL
Y VIDEO Y VIDEO
CD 3 CD 3
DVD 1 DVD 1
R R R R
COAXIAL COAXIAL
SUBWOOFER SUBWOOFER
V L R V
O V L R V L R L R V
Audio out
Video out
Video in
Audio out
Audio out
Audio out
Video out
Video out
Audio in
Video in
Audio out
C
DVD player
Cable TV or DVD recorder
Video monitor Satellite tuner
16 En
Downloaded from www.Manualslib.com manuals search engine
Connections
Note
Be sure to connect your video components in the same way you connect your video monitor to this unit. For example, if you connect
your video monitor to this unit using a HDMI connection, connect your video components to this unit using the HDMI connection.
HDMI connection
Video monitor
Audio signals input at the HDMI jack are not output
Cable TV or
from any speaker terminals but output from the satellite tuner
PREPARATION
connected video monitor.
To enjoy the sound from speakers connected to this
unit,
– make an analog or digital connection besides the
HDMI connection (see page 16).
– mute the volume of the connected video monitor.
Notes
• When you connect your TV monitor or projector via HDMI ANTENNA
connection, the OSD does not appear. In such cases, connect the OUT DVD DTV/CBL
connection. S VIDEO
AM
GND
UNBAL.
monitor only when this unit is turned on and set to the input R
DVD player
English
17 En
Downloaded from www.Manualslib.com manuals search engine
Connections
Video out
Video in
Video out
Video in
S S
Y PB PR Y PB PR
S VIDEO
PR
PB
VIDEO
Y
AUDIO
MULTI CH INPUT DVD DTV/CBL DVR OUT CD
IN
FRONT SURROUND CENTER
L
L
R
R
SUBWOOFER
S S S
Video out
Video out
Video in
Y PB PR Y PB PR
Video out
Video out
18 En
Downloaded from www.Manualslib.com manuals search engine
Connections
PREPARATION
DIGITAL INPUT
PB
FM
R SURROUN
75
OPTICAL UNBAL.
Y VIDEO
CD 3
DVD 1
R R
COAXIAL
SUBWOOFER
O L R L R L R
CD player CD recorder or
MD recorder
DTV/
CBL 2
FRONT SURROUND CENTER Notes
L
DVD 1
• When you select the component connected to the MULTI CH
COAXIAL
R
INPUT jacks as the input source (see page 33), this unit
SUBWOOFER
automatically turns off the digital sound field processor, and
you cannot select sound field programs.
• This unit does not redirect signals input at the MULTI CH
INPUT jacks to accommodate for missing speakers. We
recommend that you connect a 5.1-channel speaker system
Subwoofer out
Center out
Front out
English
Multi-format player or
external decoder
19 En
Downloaded from www.Manualslib.com manuals search engine
Connections
STANDBY
/ON
EDIT
PRESET/TUNING FM/AM A/B/C/D/E l
SCENE
PRESET/TUNING h MEMORY TUNING AUTO/MAN'L
VIDEO AUX
VIDEO L AUDIO R
V L R ANTENNA
Video Audio
output output
R
AM
GND
FM
75
UNBAL.
IN MD/ O
Game console or (PLAY) CD-R (R
video camera
Ground
For maximum safety and minimum
interference, connect the antenna GND
terminal to a good earth ground. A good
earth ground is a metal stake driven into
moist earth.
20 En
Downloaded from www.Manualslib.com manuals search engine
Connections
AC OUTLETS
Press 1 STANDBY/ON (or M POWER) to turn
on this unit.
y
When you turn on this unit, there will be a 4 to 5-second delay
before this unit can reproduce sound.
PREPARATION
Press 1 STANDBY/ON (or N STANDBY) to set
this unit to the standby mode.
In the standby mode, this unit consumes a small amount of
Power cable power in order to receive infrared signals from the remote
control.
■ AC OUTLETS (SWITCHED)
Use these outlets to supply power to any connected
components. Connect the power cable of your other
components to these outlets. Power to these outlets is
supplied when this unit is turned on. However, power to
these outlets is cut off when this unit is set to the standby
mode. For information on the maximum power or the total
power consumption of the components that can be
connected to these outlets, see “Specifications” on
page 70.
English
21 En
Downloaded from www.Manualslib.com manuals search engine
Connections
1 2 3 4 5 6 7 8 9
0 A B C D E F G
22 En
Downloaded from www.Manualslib.com manuals search engine
Connections
VOLUME
OPTIMIZER MIC
STANDBY
/ON
EDIT
PRESET/TUNING FM/AM A/B/C/D/E l PRESET/TUNING h MEMORY TUNING AUTO/MAN'L
SCENE
1 2 3 4
PREPARATION
30º 30º Approximately 6 m (20 ft)
Y Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
y
To set the remote control codes for other components, see
page 59.
Notes
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types
of conditions:
– places of high humidity, such as near a bath
– places of high temperature, such as near a heater or stove
– places of extremely low temperatures
– dusty places
English
23 En
Downloaded from www.Manualslib.com manuals search engine
Optimizing the speaker setting for your listening room
AUDIO SELECT
satisfactory.
y
You can run “AUTO SETUP” using the system menu that appears
in the OSD or in the front panel display. This manual uses the
OSD illustrations to explain the “AUTO SETUP” procedure.
Optimizer
1 Make sure of the following check points microphone
before starting the AUTO SETUP operations. The following display appears in the OSD.
❏ Speakers are connected appropriately.
❏ Headphones are disconnected from this unit. AUTO:MENU
y
It is recommended that you use a tripod (etc.) to affix the
optimizer microphone at the same height as your ears would be
when you are seated in your listening position. You can use the
attached screw of a tripod (etc.) to fix the optimizer microphone
to the tripod (etc.).
24 En
Downloaded from www.Manualslib.com manuals search engine
Optimizing the speaker setting for your listening room
y SETUP;;;;;;;AUTO
. START
You can also select the following setup methods. In this
Automatic
case, press G k to select “SETUP”, press G l / h to processing
of all item
select the one of the following choises and then select [ ]/[ ]:Up/Down
p
p
[ENTER]:Start
“START”.
Choices: AUTO, RELOAD, UNDO, DEFAULT
• Select “AUTO” to automatically run the entire
“AUTO SETUP” procedure.
PREPARATION
• Select “RELOAD” to reload the last “AUTO AUTO:CHECK
[
[]:Exit
Note
“RELOAD” or “UNDO” is available only when you have AUTO:RESULT
previously run “AUTO SETUP” and confirmed the results.
NO WARNING
RESULT
Press D AMP and then press G ENTER to
SP : 3/2/0.1
5 DIST: 3.2/3.5m
LVL : -2/+2dB
start the setup procedure. . >SET CANCEL
[ ]/[ ]:Up/Down
This unit starts the auto setup procedure. Loud test [ENTER]:Enter
tones are output from each speaker during the auto The results displayed under “RESULT” are as follows.
setup procedure. Once all items are set, the
Number of speakers SP
“AUTO:RESULT” display appears in the OSD.
Displays the number of speakers connected to this unit in
the following order:
Notes
Front/Back/Subwoofer
• During the auto setup procedure, do not perform any
operation on this unit. Speaker distance DIST
• We recommend getting out of the room while this unit is in Displays the speaker distance from the listening position
the auto setup procedure. It takes approximately 3 minutes in the following order:
for this unit to complete the auto setup procedure. Closest speaker distance/Farthest speaker distance
Speaker level LVL
This unit performs the following checks: Displays the speaker output level in the following order:
Lowest speaker output level/Highest speaker output level
Speaker wiring/volume level WIRING/LEVEL
Checks which speakers are connected and the Notes
polarity of each speaker. Also checks and adjusts the • If “E-6:INTERNAL ERROR” appears during the testing
volume level of each speaker. procedure, restart from step 4.
• If you selected “RELOAD” in step 4, no test tones are output.
Speaker distance DISTANCE • If an error occurs during the “AUTO:CHECK” procedure, the
Checks the distance of each speaker from the setup procedure is canceled and an error screen appears. For
listening position and adjusts the timing of each details, see “If an error screen appears” on page 27.
channel. • When this unit detects potential problems during the “AUTO
SETUP” procedure, “WARNING” and the number of warning
messages appears in the above of “RESULT” (see page 27).
Speaker size SIZE
Checks the frequency response of each speaker and
sets the appropriate low-frequency crossover for each
English
channel.
25 En
Downloaded from www.Manualslib.com manuals search engine
Optimizing the speaker setting for your listening room
6 Press G ENTER to display the setup results 9 Make sure the pointer is pointing at “SET”
in detail. and “CANCEL” and then press G l / h to
select “SET” or “CANCEL”.
7 Press G l / h repeatedly to toggle between Choices: SET, CANCEL
the setup result displays. • Select “SET” to confirm the “AUTO SETUP”
results.
Results of the speaker • Select “CANCEL” to cancel the “AUTO SETUP”
connection and wiring results.
TOP MENU
. ;AUTO SETUP
;MANUAL SETUP
.A;SIGNAL INFO
p
p
size [ENTER]:Enter
AUTO:RESULT
NO WARNING
RESULT
SP : 3/2/0.1
DIST: 3.2/3.5m
LVL : -2/+2dB
. >SET CANCEL
[ ]/[ ]:Up/Down
[ENTER]:Enter
26 En
Downloaded from www.Manualslib.com manuals search engine
Optimizing the speaker setting for your listening room
PREPARATION
[ ]/[ ]:Select
[ENTER]:Return
display the detailed information about the
Choices: RETRY, EXIT warning.
• Select “RETRY” to retry the “AUTO SETUP” The number on the right of “WARNING” indicates
procedure. the number of warning messages.
• Select “EXIT” to exit from the “AUTO SETUP”
procedure. AUTO:RESULT
. WARNING(1)
RESULT
SP : 3/2/0.1
DIST: 3.2/3.5m
LVL : -2/+2dB
>SET CANCEL
[ ]/[ ]:Up/Down
[ENTER]:Enter
WARNING:W-1
<OUT OF PHASE>
Reverse Channel
-- FR
CENTER
-- --
[p]/[[]:Select
[ENTER]:Return
y
• For details about each warning message, see the “AUTO
SETUP” section in “Troubleshooting” on page 65.
• When the corresponding warning message is not
applicable to a speaker, “– –” is displayed instead.
27 En
Downloaded from www.Manualslib.com manuals search engine
SELECTING THE SCENE TEMPLATES
Remote control
DVD MovieView
Assign the
SCENE
SCENE template library template to the
(Image) SCENE button 3 Press the F SCENE (or E SCENE) button
again to confirm the selection.
The selected SCENE template is assigned to the
button.
Selecting the desired SCENE
template 1 or 1
Flashes
DVD Viewing
28 En
Downloaded from www.Manualslib.com manuals search engine
Selecting the SCENE templates
Video sources
(DVD video, DVD DVD Viewing 1
Recorded video)
OPERATION
Disc Listening 2
BASIC
CD CD HiFi Listening
CD Listening
CD Music Listening
TV Sports Viewing
y
You can create your original SCENE templates by editing the preset SCENE templates. See page 31 for details.
English
29 En
Downloaded from www.Manualslib.com manuals search engine
Selecting the SCENE templates
DVD Viewing
(SCENE 1 as the default setting) CD Music Listening
Select this SCENE template when you play back general contents Select this SCENE template when you play back the music source
on your DVD player. on your CD player as the background music.
Select this SCENE template when you enjoy music live video on USB Audio Listening
your DVD player.
Select this SCENE template when you play back music on your
DVD Pop/Rock USB memory device or a USB portable audio player.
MUSIC ENHANCER
DVR Viewing USB
5ch STEREO
Select this SCENE template when you play back movies on your
digital video recorder.
TV Viewing (SCENE 3 as the default setting)
DVR Movie Dramatic
Select this SCENE template when you enjoy TV programs.
DTV/CBL STRAIGHT
Disc HiFi Listening
Select this SCENE template when you enjoy the high fidelity
TV Sports Viewing
sound of the music discs on your DVD player.
Select this SCENE template when you enjoy sports programs on
DVD DIRECT STEREO
TV.
DTV/CBL TV Sports
Music Disc Listening
Select this SCENE template when you play back music discs on
Game Playing
your DVD player.
Select this SCENE template when you play video games.
DVD 2ch Stereo
V-AUX Game
Disc Listening
(SCENE 2 as the default setting)
Select this SCENE template when you play back music sources on
your DVD player as the background music.
DVD 5ch Stereo
CD HiFi Listening
Select this SCENE template when you enjoy the high fidelity
sound of the music discs on your CD player.
CD DIRECT STEREO
30 En
Downloaded from www.Manualslib.com manuals search engine
Selecting the SCENE templates
OPERATION
(Image)
BASIC
4 Press the E SCENE button again to confirm
the edit.
1
1
Assign to the SCENE
button
y
An asterisk mark (*) appears by the name of the original SCENE
1 Turn on the video monitor connected to this template.
unit.
Notes
• Once the desired SCENE templates are assigned to the
2 Press and hold the desired E SCENE button
corresponding E SCENE buttons, you may need to set the
for 3 seconds and then press D AMP. input source of the SCENE template on the remote control. See
The SCENE template customizing screen appears on page 56 for details.
the video monitor. • You can create a customized SCENE template for each
E SCENE button, and if you create another customized
AMP SCENE template, this unit overwrites the old customized
1 SCENE template with the new one.
• The newly created template is only available for the assigned
E SCENE button.
3 seconds
■ Renaming the SCENE templates
Note
Select “SCENE” in step 3 of “Customizing the
When the SCENE template you want to customize is not
preset SCENE templates” and then press
assigned to any of the E SCENE button, press G l / h
repeatedly to recall the desired SCENE template on the G ENTER.
menu screen. • Press G k / n to select the desired character.
• Press G l / h to place “_” (underscore) under the
space or the desired character.
• Press H RETURN to cancel the new name.
• Press G ENTER to confirm the new name.
English
31 En
Downloaded from www.Manualslib.com manuals search engine
PLAYBACK
Playback
See
When you want to...
page
3 Start playback on the selected component or Enjoy pure hi-fi stereo sound 34
select a broadcast station.
Adjust the tonal quality of the front speakers 34
• Refer to the operating instructions for the source
component. Adjust the parameters of sound field programs 39
• See page 40 for details about FM/AM tuning
Enjoy the sources with a wide dynamic range at night 35
instructions.
Use headphones 36
4 Rotate 8 VOLUME (or press R VOLUME +/–) Select a decoder to play back sources with 38
to adjust the volume to the desired output Automatically set this unit to the standby mode 36
level.
32 En
Downloaded from www.Manualslib.com manuals search engine
Playback
OPERATION
front left and right channels.
feature (audio input jack select) to switch between input
BASIC
jacks when more than one input jack is assigned to the
■ Selecting the front speaker set same input source.
Use this feature to select the front speaker system
(FRONT A or FRONT B). y
• We recommend setting audio input jack select to “AUTO” in
most cases.
Press 9 SPEAKERS on the front panel • You can adjust the default audio input jack select of this unit by
using “AUDIO SELECT” in “OPTION MENU” (see page 55).
repeatedly to turn on or off the set of front
speakers connected to the FRONT A or FRONT B
Press E AUDIO SELECT (or B AUDIO SEL)
speaker terminals.
repeatedly to select the desired audio input jack
The activate front speaker set changes as follows:
select setting.
DVR V-AUX DTV/CBL DVD MD/CD-R TUNER CD
FRONT A FRONT B USB
Off
A.SEL:AUTO
Audio input jack
select setting
Note
AUTO Automatically selects input signals in the
Turn off the volume level of this unit when you switch the front
following order:
speaker setting.
(1) Digital signals
(2) Analog signals
ANALOG Selects only analog signals. If no analog
signals are input, no sound is output.
Note
This feature is not available when no digital input jacks are
assigned to the currently selected input source.
English
33 En
Downloaded from www.Manualslib.com manuals search engine
Playback
34 En
Downloaded from www.Manualslib.com manuals search engine
Playback
1 Press D AMP and then press L NIGHT 1 Press D AMP and then press Q MENU on
repeatedly to select “NIGHT:CINEMA” or the remote control.
“NIGHT:MUSIC”. The top “SET MENU” display appears in the OSD.
Choices: NIGHT:CINEMA, NIGHT:MUSIC, OFF
• Select “NIGHT:CINEMA” to reduce the dynamic SET MENU
p
p
• Select “OFF” if you do not want to use this feature. [ENTER]:Enter
y
When a night listening mode is selected, the NIGHT 2 Press G n repeatedly to select “SIGNAL
indicator lights up in the front panel display.
INFO” and then press G ENTER.
The following information about the input source
2 Press G l / h to adjust the effect level while appears in the OSD.
OPERATION
“NIGHT:CINEMA” or “NIGHT:MUSIC” is
BASIC
displayed in the front panel display. ;SIGNAL INFO
Choices: MIN, MID, MAX
. FORMAT DolbyD
• Select “MIN” for minimum compression. SAMPLING 48kHz
CHANNEL 3/2/0.1
• Select “MID” for standard compression. BITRATE 384kbps
FLAG None
• Select “MAX” for maximum compression.
[RETURN]:Exit
y
“NIGHT:CINEMA” and “NIGHT:MUSIC” adjustments are
stored independently. Display Description
Notes FORMAT Signal format.
• You cannot use the night listening modes in the following cases: The number of samples per second taken
– when the DIRECT STEREO mode (see page 34) is selected. SAMPLING from a continuous signal to make a
– when the component connected to the MULTI CH INPUT discrete signal.
jacks is selected as the input source.
The number of source channels in the
– when headphones are connected to the PHONES jack. CHANNEL input signal (front/surround/LFE).
– when the sound field program is selected while you enjoy
music contents in a USB memory device etc. The number of bits passing a given point
BITRATE per second.
• The night listening modes may vary in effectiveness depending
on the input source and surround sound settings you use.
Flag data encoded in DTS, Dolby Digital,
FLAG or PCM signals that cue this unit to
automatically switch decoders.
y
The information indicated by the cursor is also displayed in
the front panel display.
35 En
Downloaded from www.Manualslib.com manuals search engine
Playback
EDIT CATEGORY
PRESET/TUNING FM/AM A/B/C/D/E l PRESET/TUNING/CH h MEMORY TUNING AUTO/MAN'L
SCENE
1 2 3 4
program.
PHONES SPEAKERS TONE CONTROL STRAIGHT DIRECT STEREO AUDIO SELECT
A/B/OFF
y
• To cancel the sleep timer, press P SLEEP on the remote
control repeatedly until “SLEEP OFF” appears in the front
panel display.
• You can also cancel the sleep timer setting by pressing
1 STANDBY/ON (or N STANDBY) to set this unit to the
standby mode.
y
When you select a sound field program, SILENT CINEMA mode
activates automatically (see page 38).
Notes
• When you connect headphones, no signals are output at the
speaker terminals.
• All Dolby Digital and DTS audio signals are mixed down to the
left and right headphone channels.
36 En
Downloaded from www.Manualslib.com manuals search engine
SOUND FIELD PROGRAMS
OPERATION
Category Program Features
BASIC
CINEMA DSP processing. This program presents an image of pop, rock, or jazz live concert. The
Pop/Rock sound field reproduces the spaciousness of a massive pavilion with an emphasis on the vividness of
vocals on the stage and solo instruments and the beats of rhythm instruments.
HiFi DSP processing. This sound field is suitable for classic and orchestral music. The program
MUSIC
Hall uses data collected in a large concert hall in Munich. You can enjoy delicate and beautiful
reverberation and a majestic atmosphere.
HiFi DSP processing. The sound field is suitable for jazz and fusion music. It uses data collected in
Jazz a famous jazz club in New York. You can enjoy clear reverberation.
CINEMA DSP processing. You can enjoy dynamic and thrilling sound effects as you play games.
Game The program lets you feel the depth and three-dimensional surrounding sounds of the field where
you are playing, and offers cinema-like surrounding sound effects for the scenes of movies.
ENTERTAIN CINEMA DSP processing. You can enjoy sports relays broadcast in stereo and variety shows with
a live sound environment. For sports relays, the voices of commentators and announcers come
TV Sports clearly from the center; the cheers and atmosphere in the stadium spread around within a
comfortable range, and you can feel like as if you are in the stadium.
CINEMA DSP processing. The sound field is suitable for movies with an emphasis on spectacular
Movie Spacious sound effects, and is a perfect fit with a wide screen. The program reproduces a wide dynamic
range from minimum sound effects to powerful sounds.
MOVIE CINEMA DSP processing. This sound field is also suitable for movies with an emphasis on three-
dimensional sound effects. It restrains reverberation to an moderate extent, but reproduces sound
Movie Dramatic effects and background music in a soft, three-dimensional manner with clarity and center
orientation of voices as pivots.
2ch Stereo Downmixes multi-channel sources to 2 channel or plays back 2-channel sources as they are.
STEREO
HiFi DSP processing. Using this program increases the listening position range. This is a sound
5ch Stereo field suitable for background music at parties.
Music Enh. 2ch Select these programs to play back compression artifacts (such as the MP3 format) in
ENHANCER 2-channel or 5-channel stereo. This program enhances your listening experience by regenerating
Music Enh. 5ch the missing harmonics in a compression artifact.
Note
The sound field programs of this unit are recreations of real-world acoustic environments made from precise measurements taken in the
actual concert hall, music venue, movie theater, etc. Thus, you may notice variations in the strength of the reflections coming from each
direction.
English
37 En
Downloaded from www.Manualslib.com manuals search engine
Sound field programs
Note
Virtual CINEMA DSP will not activate even when “SUR. L/R
SP” is set to “NONE” (see page 49) in the following cases:
– When “5ch Stereo” (see page 37) is selected.
– When headphones are connected to the PHONES jack.
38 En
Downloaded from www.Manualslib.com manuals search engine
Sound field programs
Note
You cannot change parameter values when “MEMORY GUARD”
in “OPTION MENU” is set to “ON” (see page 55).
y
Initial settings are indicated in bold under each parameter.
OPERATION
For Pop/Rock, Hall, Jazz, Game, TV Sports,
BASIC
Movie Spacious and Movie Dramatic:
DSP level DSP LEVEL
Function: Adjusts the effect level.
Choices: MIN, MID, MAX
For PRO LOGIC II Music:
Panorama PANORAMA
Function: Sends stereo signals to the surround
speakers as well as the front speakers for
a wraparound effect.
Choices: OFF, ON
Dimension DIMENSION
Function: Gradually adjusts the sound field either
towards the front or towards the rear.
Control range: –3 (towards the rear) to +3 (towards the
front), initial setting is STD (standard).
Center width CT WIDTH
Function: Adjusts the center image from all three
front speakers to varying degrees. A
larger value adjusts the center image
towards the front left and right speakers.
Control range: 0 (center channel sound is output only
from center speaker) to 7 (center channel
sound is output only from front left and
right speakers), initial setting is 3.
For Music Enh. 2ch and Music Enh. 5ch
Effect level
Function: Adjusts the effect level.
Choices: LOW, HIGH
English
39 En
Downloaded from www.Manualslib.com manuals search engine
FM/AM TUNING
FM/AM tuning
There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and
there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use
the automatic and manual preset tuning features to store up to 40 stations.
2 Press 3 FM/AM to select the reception band 1 Press D INPUT l / h repeatedly so that
(FM or AM). “TUNER” is displayed in the front panel
display.
3 Press 7 TUNING AUTO/MAN’L so that the
AUTO indicator lights up in the front panel 2 Press 3 FM/AM to select the reception band
display. (FM or AM).
Lights up
3 Press 7 TUNING AUTO/MAN’L so that the
AUTO AUTO indicator disappears from the front
panel display.
A AM 1440 kHz
No colon (:)
If a colon (:) appears in the front panel display, A AM 1440 kHz
automatic tuning is not possible. Press 2 PRESET/
TUNING to turn the colon (:) off. No colon (:)
If a colon (:) appears in the front panel display,
4 Press 5 PRESET/TUNING l / h once to manual tuning is not possible. Press 2 PRESET/
begin automatic tuning. TUNING to turn the colon (:) off.
When this unit is tuned into a station, the TUNED
indicator lights up and the frequency of the received 4 Press 5 PRESET/TUNING l / h to tune
station is shown in the front panel display. into the desired station manually.
Lights up y
Hold down the button to continue searching.
AUTO TUNED
A AM 1530 kHz
40 En
Downloaded from www.Manualslib.com manuals search engine
FM/AM tuning
OPERATION
and AUTO indicators flashes. After approximately 5 display.
BASIC
seconds, automatic presetting starts from the current Flashes
frequency and proceeds toward the higher
frequencies. TUNED MEMORY
Flash
C3 : AM 630 kHz
AUTO MEMORY Preset station number
41 En
Downloaded from www.Manualslib.com manuals search engine
FM/AM tuning
A5 : FM 90.7 MHz
Flashes
42 En
Downloaded from www.Manualslib.com manuals search engine
USING A USB MEMORY DEVICE OR A USB PORTABLE AUDIO PLAYER
OPERATION
DVR V-AUX DTV/CBL DVD MD/CD-R TUNER CD
USB
USB potable audio player
BASIC
INPUT:USB
Connect a USB jack of a USB memory device or
USB portable audio player to the USB port on the
front panel of this unit. 2 Press S DISPLAY to display the top USB file
list.
VOLUME
The USB file list appears in the OSD.
OPTIMIZER MIC
STANDBY
/ON
EDIT
PRESET/TUNING FM/AM A/B/C/D/E l PRESET/TUNING h MEMORY TUNING AUTO/MAN'L
y
• “i” in the right corner of each menu line indicates that
USB memory device there is a submenu available in the next menu level.
or USB portable
• When this unit is in the top directory, “Root” appears
audio player
beside “USB”.
English
43 En
Downloaded from www.Manualslib.com manuals search engine
Using a USB memory device or a USB portable audio player
5 (playback) icon
7 (shuffle) icon
When “SHUFFLE” of the “USB PLAY STYLE” in
“OPTION MENU” (see page 55) is set to “OFF”, no icon
appears in the top right corner while files or holders are being
played.
44 En
Downloaded from www.Manualslib.com manuals search engine
RECORDING
Recording
Recording adjustments and other operations are performed from the recording components. Refer to the operating
instructions for those components.
Notes
• When this unit is set to the standby mode, you cannot record between other components connected to this unit.
• TONE CONTROL (see page 34) and VOLUME settings, speaker levels (see page 34) and the sound field programs (see page 37) do
not affect recorded material.
• The source connected to the USB jack or the MULTI CH INPUT jacks of this unit cannot be recorded.
• Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Therefore, if
your source component is connected to provide only digital signals, you cannot record the source.
• S-video and composite video signals pass independently through the video circuits of this unit. Therefore, when recording or dubbing
video signals input from a video source component that provides only an S-video or a composite video signal, you can record only an
S-video or a composite video signal on your DVD recorder.
• A given input source is not output on the same OUT (REC) channel.
• Once you have connected a recording component to this unit, keep the component turned on while using this unit. If the component is
turned off, this unit may distort the sound from other components.
• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright
laws.
OPERATION
y
BASIC
Do a test recording before you start an actual recording.
If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture
itself may be disturbed due to those signals.
1 Turn on all the connected components. 3 Start playback on the selected source
component or select a broadcast station.
2 Press D INPUT l / h repeatedly (or press
one of the input selector buttons (C)) to 4 Start recording on the recording component.
select the source component you want to
record from.
English
45 En
Downloaded from www.Manualslib.com manuals search engine
SET MENU
SET MENU
You can use the following parameters in “SET MENU” to adjust a variety of system settings and customize the way this
unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening
environment.
Selects the size of each speaker, the speakers for low-frequency signal output, and the
A)SPEAKER SET crossover frequency, and the location of the front speakers connected to the FRONT B 48
terminals.
E)LFE LEVEL Adjusts the output level of the LFE channel for Dolby Digital or DTS signals. 51
G)AUDIO SET Adjusts the muting level, audio delay, maximum volume level and initial volume level. 51
A)INPUT ASSIGN Assigns the input jacks of this unit according to the component to be used. 52
Selects the decoder mode for the sources connected to the DIGITAL INPUT jacks on the
D)DECODER MODE rear panel of this unit.
53
Selects the video source played in the background of the sources input from the MULTI CH
E)MULTI CH SET INPUT jacks.
54
46 En
Downloaded from www.Manualslib.com manuals search engine
SET MENU
B)MEMORY GUARD Locks sound field program parameters and other “SET MENU” settings. 55
Designates the default audio input jack select setting for the input sources connected to the
C)AUDIO SELECT DIGITAL INPUT jacks when you turn on the power of this unit.
55
D)PARAM. INI Sets all the parameters of the sound field programs to the factory settings. 55
OPERATION
ADVANCED
3 OPTION MENU
[ENTER]:Enter
confirm the parameter.
• Press H RETURN to return to the previous menu
2 Press G k / n to select “MANUAL SETUP”. level.
[ ]/[ ]:Up/Down
p
p
[ENTER]:Enter
English
47 En
Downloaded from www.Manualslib.com manuals search engine
SET MENU
p
p
p
[ENTER]:Enter [ENTER]:Enter A)SPEAKER SET
FRONT SP
[p]/[[]:Select
this unit automatically changes the value to “LARGE”.
48 En
Downloaded from www.Manualslib.com manuals search engine
SET MENU
1 SOUND MENU
1 SOUND MENU
A)SPEAKER SET
OPERATION
ADVANCED
LFE/BASS OUT >NORMAL REVERSE
49 En
Downloaded from www.Manualslib.com manuals search engine
SET MENU
[p]/[[]:Adjust . UNIT;;;;;;;;feet
FRONT L;;;10.0ft
FRONT R;;;10.0ft
CENTER;;;;10.0ft
[ ]/[ ]:Up/Down
p
p
SP LEVEL Adjusted speaker [p]/[[]:Adjust
SWFR Subwoofer
Note
The available speaker channels differ depending on the setting of
the speakers.
50 En
Downloaded from www.Manualslib.com manuals search engine
SET MENU
[ ]/[ ]:Up/Down
p
p
1 SOUND MENU [p]/[[]:Adjust
D)CENTER GEQ
TEST >OFF ON
. 100Hz ;;;;;; 0.0dB Speaker SP
300Hz ;;;;;; 0.0dB
1kHz ;;;;;; 0.0dB
3kHz ;;;;;; 0.0dB Adjusts the speaker compression.
10kHz ;;;;;; 0.0dB
[ ]/[ ]:Up/Down
p
p
[p]/[[]:Adjust Headphone HP
Adjusts the headphone compression.
Test tone TEST
Choices: MIN, STD, MAX
Use this feature to make adjustments for “CENTER GEQ” • Select “MIN” (minimum) if you regularly listen at low
while listening to a test tone. volume levels.
Choices: OFF, ON • Select “STD” (standard) for general use.
• Select “OFF” to stop test tones and output the currently • Select “MAX” (maximum) to preserve the greatest
selected source component. amount of dynamic range.
• Select “ON” to output test tones from the center and
front left speakers. ■ Audio settings G)AUDIO SET
Use this feature to adjust the overall audio settings of this
OPERATION
ADVANCED
■ Low-frequency effect level E)LFE LEVEL unit.
Use this feature to adjust the output level of the LFE (low-
frequency effect) channel according to the capacity of
1 SOUND MENU
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to G)AUDIO SET
certain scenes. This setting is effective only when this unit . MUTE TYPE;;;FULL
A.DELAY;;;;;;0ms
decodes Dolby Digital or DTS signals. MAX VOL.;;;+16dB
INI.VOL.;;;;;OFF
Control range: –20 to 0 dB [ ]/[ ]:Up/Down
p
p
[p]/[[]:Adjust
Control step: 1 dB
1 SOUND MENU
Mute type MUTE TYPE
Use this feature to adjust how much the mute function
E)LFE LEVEL
reduces the output volume (see page 36).
. SPEAKER;;;;;;0dB
HEADPHONE;;;;0dB Choices: FULL, –20dB
• Select “FULL” to completely mute all the audio
[ ]/[ ]:Up/Down output.
p
p
[p]/[[]:Adjust
• Select “–20dB” to reduce the current volume by 20 dB.
51 En
Downloaded from www.Manualslib.com manuals search engine
SET MENU
p
p
The “MAX VOL.” setting takes priority over the “INI.VOL.” [ENTER]:Enter
setting. For example, if “INI.VOL.” is set to –20 dB and “MAX
VOL.” is set to –30 dB, the volume level is automatically set to
–30 dB when you turn on the power of this unit next time. ■ Input assignment
A)INPUT ASSIGN
Initial volume INI.VOL. Use this feature to assign the input jacks according to the
Use this feature to set the volume level when the power of component to be used if the initial settings of this unit do
this unit is turned on. not correspond to your needs. Change the following
Choices: OFF, –80 dB to +16 dB parameters to reassign the respective jacks and effectively
Control step: 1 dB connect more components.
Once the input jacks are reassigned, you can select the
Note corresponding component by using D INPUT l / h (or
The “MAX VOL.” setting takes priority over the “INI.VOL.” the input selector buttons (C)).
setting.
For COAXIAL INPUT jack 1
COAXIAL IN (1)
Choices: (1) CD, MD/CD-R, DVD, DTV/CBL,
V-AUX, DVR
2 INPUT MENU
A)INPUT ASSIGN
COAXIAL IN
. (1);;;;; DVD
( DVD )
[p]/[[]:Select
2 INPUT MENU
A)INPUT ASSIGN
OPTICAL IN
. (2);;;;;DTV/CBL
(DTV/CBL )
(3);;;;; CD
( CD )
[p]/[[]:Select
Note
You cannot select a specific item more than once.
52 En
Downloaded from www.Manualslib.com manuals search engine
SET MENU
[p]/[[]:Adjust
[RETURN]:Exit
CD MD/CD-R TUNER
D)DECODER MODE
. >AUTO LAST
2 Press D AMP and then press G l / h on the CD
DVD
;;;;AUTO
;;;;AUTO
remote control to place the “_” (underscore) DTV/CBL ;;;;AUTO
OPERATION
[ ]/[ ]:Up/Down
ADVANCED
p
under the space or the character you want to [p]/[[]:Select
edit.
Decoder select mode
3 Press G k / n to select the character you Use this feature to designate the default decoder mode for
want to use and then press G l / h to move the input sources connected to the DIGITAL INPUT jacks
to the next space. when you turn on the power of this unit.
Choices: AUTO, LAST
Notes • Select “AUTO” if you want this unit to automatically
• You can use up to 8 characters for each input. detect the type of input signals and select the
• Press G n to change the character in the following order, appropriate decoder mode.
or press G k to go in the reverse order: • Select “LAST” if you want this unit to automatically
A to Z, a space, 0 to 9, a space, a to z, a space, symbols (#, select the last decoder mode used the connected input
*, –, +, etc.) source.
DTS decoder prioritize setting
4 Repeat steps 1 through 3 to rename each Choices: AUTO, DTS
input source. • Select “AUTO” if you want this unit to automatically
detect input signal types and select the appropriate
5 Press G ENTER to exit from “INPUT input mode.
RENAME”. • Select “DTS” when you play back a DTS-CD.
English
53 En
Downloaded from www.Manualslib.com manuals search engine
SET MENU
[ ]/[ ]:Up/Down
p
[ENTER]:Enter
perform a certain operation.
• Select “30s” to turn off the OSD 30 seconds after you
■ Display settings A)DISPLAY SET perform a certain operation.
Amplifier function OSD display time
3 OPTION MENU
OSD-AMP
A)DISPLAY SET Use this feature to set the amount of time to display the
. DIMMER;;;;;;;;;0 status and sound field parameters information screen after
FL SCROLL;;;CONT
OSD SHIFT;;;;;;0 you perform a certain operation.
OSD-SOURCE;;;30s
OSD-AMP;;;;;;30s Choices: ON, 10s, 30s
[ ]/[ ]:Up/Down
p
p
[p]/[[]:Select
• Select “ON” to display the OSD constantly during an
operation.
Dimmer DIMMER • Select “10s” to turn off the OSD 10 seconds after you
Use this feature to adjust the brightness of the front panel perform a certain operation.
display. • Select “30s” to turn off the OSD 30 seconds after you
Control range: – 4 to 0 perform a certain operation.
Control step: 1
• Press G l to make the front panel display dimmer.
• Press G h to make the front panel display brighter.
54 En
Downloaded from www.Manualslib.com manuals search engine
SET MENU
[p]/[[]:Select [p]/[[]:Select
[ENTER]:Return
• Select “OFF” to turn off the “MEMORY GUARD” • Select “NO” to cancel the parameter initialization and
feature. return to the previous menu screen.
• Select “ON” to protect: • Select “YES” and then press G ENTER to set all the
– sound field program parameters sound field parameters to the initial factory settings.
– all “SET MENU” items
– all speaker levels Notes
– SCENE template parameters • You cannot automatically revert to the previous parameter
settings once you initialize the sound field program parameters.
Note
• You cannot separately initialize individual sound field
When “MEMORY GUARD” is set to “ON”, you cannot select programs.
and adjust any other “SET MENU” items. • You cannot initialize any sound field program groups when
“MEMORY GUARD” is set to “ON”.
■ Audio select C)AUDIO SELECT
Use this feature to designate the default audio input jack ■ USB playback styles E)USB PLAY STYLE
select setting for the input sources when you turn on the Use this feature to adjust the playback style according to
your preference. You can shuffle files in a random order or
OPERATION
power of this unit.
ADVANCED
Choices: AUTO, LAST repeat one specific file or a sequence of files.
[p]/[[]:Select
55 En
Downloaded from www.Manualslib.com manuals search engine
Remote control features
1 Press the desired E SCENE button on the Press and hold the E SCENE button and the
remote control. desired input selector button (C) for 3 seconds.
y
2 Press the desired buttons in the * area below Press the E SCENE button again to operate the input source
to control the input source component of the component.
selected SCENE template.
CD MD/CD-R TUNER
V-AUX USB
SCENE
* 1 2
SCENE
3 4
buttons
BAND LEVEL
TITLE MENU VOLUME
ENTER
RETURN DISPLAY
REC
9 0 10 ENT
Note
* These buttons control the input source component. See page 58
for details of the function of each button.
56 En
Downloaded from www.Manualslib.com manuals search engine
Remote control features
CD MD/CD-R TUNER
POWER POWER STANDBY POWER
TV AV
BAND LEVEL
TITLE MENU VOLUME
SCENE
1 2 3 4
ENTER
BAND LEVEL
TITLE MENU VOLUME
RETURN DISPLAY
ENTER
*2
REC
RETURN DISPLAY
FREQ/TEXT EON MODE – PTY SEEK – START
REC
*2
l PROG h ENHANCER STRAIGHT
1 2 3 4
SUR.DECODE NIGHT DIRECT ST.
5 6 7 8
FREQ/TEXT EON MODE – PTY SEEK – START
9 0 10 ENT
l PROG h ENHANCER STRAIGHT
1 2 3 4
SUR.DECODE NIGHT DIRECT ST.
5 6 7 8
9 0 10 ENT
OPERATION
ADVANCED
Notes
*1 These buttons always control this unit regardless of the
operation mode selector position. Notes
*2 These buttons control this unit only when D AMP is pressed. *1 These buttons always control your TV regardless of whether
you press C DTV/CBL or not.
57 En
Downloaded from www.Manualslib.com manuals search engine
Remote control features
page 59). The following table shows the function of each MULTI CH IN AUDIO SEL SLEEP MUTE
3 ENTER
V-AUX USB
may not correctly operate the selected component. AMP TV INPUT TV MUTE TV VOL
FREQ/TEXT EON MODE – PTY SEEK – START
y l
1
PROG h
2
ENHANCER STRAIGHT
3 4
6
SCENE
SUR.DECODE NIGHT DIRECT ST.
DVD
Remote Digital TV/ MD/CD
player/ VCR LD player CD player Tuner USB
control Cable TV recorder
recorder
1 AV POWER Power *1 Power *1 Power *2 Power *1 Power *1 Power *1
2 TITLE Title Band
3 PRESET/CH k Up VCR channel
Up Preset up (1-8) Up
up
VCR channel Preset down
PRESET/CH n Down Down Down
down (1-8)
Preset down
A/B/C/D/E l Left Left Previous menu
(A-E)
Preset up Subsequent
A/B/C/D/E h Right Right
(A-E) menu
Subsequent
ENTER Enter Enter
menu
4 RETURN Return Return Previous menu
5 REC/ Disc skip
DISC SKIP (player) Rec Rec *2 Disc skip Rec
Rec (recorder)
p Play Play Play *2 Play Play Play Play
Search Search Search Search Search Search
w
backward backward backward *2 backward backward backward
Search forward
f Search forward Search forward Search forward Search forward Search forward
*2
e Pause Pause Pause *2 Pause Pause Pause
Skip backward
b Skip backward Skip backward Skip backward Skip backward Skip backward Skip backward
*2
Skip forward
a Skip forward Skip forward Skip forward Skip forward Skip forward Skip forward
*2
s Stop Stop Stop *2 Stop Stop Stop Stop
6 1-9, 0, +10 Numeric Numeric Numeric Numeric Numeric Numeric Preset stations
buttons buttons buttons buttons buttons buttons (1-8)
7 MENU Menu Menu
8 DISPLAY Display Display Display Display Display Display Display
9 ENT Title/Index Enter Enter Chapter/Time Index Index
Notes
*1 This button is operational only when the original remote control supplied with the component has a POWER button.
*2 These buttons operate your DVD recorder only when you set the appropriate remote control code for DVR (see page 59).
58 En
Downloaded from www.Manualslib.com manuals search engine
Remote control features
Setting remote control codes 1 While pressing and holding one of the input
selector buttons (C) on the remote control to
You can control other components by setting the
select the input area you want to set up,
appropriate remote control codes. For a complete list of
available remote control codes, refer to “List of remote press AV POWER for more than 3 seconds.
control codes” at the end of this manual. CD MD/CD-R TUNER
CD CD YAMAHA 5013
While holding down Press for 3 seconds
MD/CD-R CD-R YAMAHA 5001
Note
OPERATION
ADVANCED
You may not be able to operate your Yamaha component even if a
Yamaha remote control code is preset as listed above. In this case,
try setting another Yamaha remote control code.
English
59 En
Downloaded from www.Manualslib.com manuals search engine
Advanced setup
Advanced setup
This unit has additional menus that are displayed in the ■ Speaker impedance SP IMP.
front panel display. The advanced setup menu offers Use this feature to set the speaker impedance of this unit
additional operations to adjust and customize the way this so that it matches that of your speakers.
unit operates. Change the initial settings (indicated in bold Choices: 8Ω MIN, 6Ω MIN
under each parameter) to reflect the needs of your • Select “8Ω MIN” to set the speaker impedance to 8 Ω .
listening environment. • Select “6Ω MIN” to set the speaker impedance to 6 Ω .
Front (A or B)
1 Press 1 STANDBY/ON on the front panel to The impedance of each
6Ω MIN Center speaker must be 6 Ω or
set this unit to the standby mode. higher.
Surround
2 Press and hold 0 TONE CONTROL and
then press 1 STANDBY/ON to turn on this ■ Factory presets PRESET
unit. Use this feature to reset all the parameters of this unit to
This unit turns on, and the advanced setup menu the initial factory settings (see page 67).
appears in the front panel display. Choices: CANCEL, RESET
• Select “CANCEL” not to reset any parameters of this
unit.
3 Press B STRAIGHT repeatedly to change
• Select “RESET” to reset the parameters of this unit.
the selected parameter setting.
Notes
4 Press 1 STANDBY/ON to confirm your • This setting completely resets all the parameters of this unit
selection and set this unit to the standby including the “SET MENU” parameters. However, the
mode. advanced setup menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on
y this unit.
The settings you made are reflected next time you turn on this
unit.
60 En
Downloaded from www.Manualslib.com manuals search engine
Troubleshooting
Troubleshooting
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
■ General
See
Problem Cause Remedy
page
This unit fails to turn The power cable is not connected or the Connect the power cable firmly.
—
on or enters the plug is not completely inserted.
standby mode soon
after the power is The speaker impedance setting is Set the speaker impedance to match your speakers.
13
turned on. incorrect.
The protection circuitry has been Make sure that all speaker wire connections on this
activated. unit and on all speakers are secure and that the wire
12
for each connection does not touch anything other
than its respective connection.
This unit has been exposed to a strong Set this unit to the standby mode, disconnect the
external electric shock (such as lightning power cable, plug it back in after 30 seconds and then —
or strong static electricity). use it normally.
No sound Incorrect input or output cable Connect the cables properly. If the problem persists,
14-20
connections. the cables may be defective.
No appropriate Audio input jack select has Set an appropriate Audio input jack select.
33
been set.
No appropriate input source has been Select an appropriate input source with D INPUT
selected. l / h on the front panel (or the input selector 32, 33
buttons (C) on the remote control).
INFORMATION
The volume is turned down. Turn up the volume. —
ADDITIONAL
The sound is muted. Press O MUTE or R VOLUME +/– on the remote
control to resume audio output and then adjust the 36
volume.
Signals this unit cannot reproduce are Play a source whose signals can be reproduced by this
being input from a source component, unit. —
such as a CD-ROM.
Audio signals input at the HDMI jack are Make an analog or digital connection beside the
—
not output from any speaker terminals. HDMI connection.
The setting of the connected component is Make an appropriate setting following the instruction
—
improper. manual of the connected component.
English
61 En
Downloaded from www.Manualslib.com manuals search engine
Troubleshooting
See
Problem Cause Remedy
page
The sound suddenly The protection circuitry has been activated Check that the impedance setting is correct. 13
goes off. because of a short circuit, etc.
Check that the speaker wires are not touching each
—
other and then turn this unit back on.
The sleep timer has turned off this unit. Turn on this unit, and play the source again. —
The sound is muted. Press O MUTE or R VOLUME +/– on the remote
36
control to resume audio output.
Sound is heard from Incorrect cable connections. Connect the cables properly. If the problem persists,
14-20
the speaker on one the cables may be defective.
side only.
Incorrect settings in “SP LEVEL”. Adjust the “SP LEVEL” settings. 34
Only the center When playing a monaural source with a This is not malfunction.
speaker outputs CINEMA DSP program, the source signal
substantial sound. is directed to the center channel, and the —
front and surround speakers output effect
sounds.
No sound is heard “CENTER” in “SET MENU” is set to Set “CENTER” to “SML” or “LRG”.
48
from the center “NONE”.
speaker.
One of the HiFi DSP programs (except for Try another sound field program.
37
5ch Stereo) has been selected.
No sound is heard “SUR. L/R SP” in “SPEAKER SET” is Set “SUR. L/R SP” to “SML” or “LRG”.
49
from the surround set to “NONE”.
speakers.
This unit is in the “STRAIGHT” mode Press B STRAIGHT on the front panel so that
and a monaural source is being played “STRAIGHT” disappears from the front panel 38
back. display.
No sound is heard “LFE/BASS OUT” in “SPEAKER SET” Set “LFE/BASS OUT” to “SWFR” or “BOTH”.
from the subwoofer. is set to “FRONT” when a Dolby Digital 49
or DTS signal is being played.
62 En
Downloaded from www.Manualslib.com manuals search engine
Troubleshooting
See
Problem Cause Remedy
page
Dolby Digital or DTS The connected component is not set to Make an appropriate setting following the operating
sources cannot be output Dolby Digital or DTS digital instructions for your component. —
played. (Dolby Digital signals.
or DTS indicator in
the front panel Audio input jack select is set to Set Audio input jack select to “AUTO”.
display does not light “ANALOG”. 33
up.)
A humming sound is Incorrect cable connections. Connect the audio cables firmly. If the problem
—
heard. persists, the cables may be defective.
The volume level You are attempting to set the volume level Adjust “MAX VOL.” setting.
52
cannot be increased, higher than the maximum volume level.
or the sound is
distorted. The component connected to the AUDIO Turn on the power of the component.
OUT (REC) jacks of this unit is turned —
off.
The sound effect It is not possible to record the sound effect This is not malfunction.
—
cannot be recorded. with a recording component.
A source cannot be The source component is not connected to Connect the source component to the analog AUDIO
recorded by an the analog AUDIO IN jacks of this unit. IN jacks.
analog component
16, 19
connected to the
AUDIO OUT (REC)
jacks.
The sound field “MEMORY GUARD” in “OPTION Set “MEMORY GUARD” to “OFF”.
parameters and some MENU” is set to “ON”.
other settings of this 55
unit cannot be
changed.
This unit does not The internal microcomputer has been Disconnect the power cable from the AC wall outlet
operate properly. frozen by an external electric shock (such and then plug it in again after about 30 seconds.
—
as lightning or excessive static electricity)
or by a power supply with low voltage.
“CHECK SP WIRES” Speaker cables are short-circuited. Make sure all speaker cables are connected correctly.
INFORMATION
appears in the front 12
ADDITIONAL
panel display.
There is noise This unit is too close to the digital or high- Move this unit further away from such equipment.
interference from frequency equipment.
—
digital or radio
frequency equipment.
The picture is The video source uses scrambled or This is not malfunction.
—
disturbed. encoded signals to prevent dubbing.
This unit suddenly The internal temperature is too high and Wait about 1 hour for this unit to cool down and then
enters the standby the overheat protection circuitry has been turn it back on. —
mode. activated.
English
63 En
Downloaded from www.Manualslib.com manuals search engine
Troubleshooting
■ Tuner
See
Problem Cause Remedy
page
FM stereo reception is The characteristics of FM stereo Check the antenna connections. 20
noisy. broadcasts may cause this problem
when the transmitter is too far away or Try using a high-quality directional FM
—
the antenna input is poor. antenna.
The desired station The signal is too weak. Use a high-quality directional FM antenna. —
cannot be tuned into
with the automatic Use the manual tuning method.
40
tuning method.
Previously preset This unit has been disconnected for a Set preset stations.
stations can no longer long period. 41
be tuned into.
The desired station The signal is weak or the antenna Tighten the AM loop antenna connections
—
cannot be tuned into connections are loose. and orient it for the best reception.
with the automatic
tuning method. Use the manual tuning method. 40
AM There are continuous Noise can result from lightning, Use an outdoor antenna and a ground wire.
crackling and hissing fluorescent lamps, motors, thermostats This will help somewhat, but it is difficult to —
noises. and other electrical equipment. eliminate all noise.
There are buzzing and A TV set is being used nearby. Move this unit away from the TV set.
—
whining noises.
■ AUTO SETUP
Before AUTO SETUP
See
Error message Cause Remedy
page
Connect MIC! Optimizer microphone is not connected. Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front 24
panel.
64 En
Downloaded from www.Manualslib.com manuals search engine
Troubleshooting
See
Error message Cause Remedy
page
E-1:NO FRONT SP Front L/R channel signals are not detected. Check the front L/R speaker connections. 12
E-2:NO SUR.SP A surround channel signal is not detected. Check the surround speaker connections. 12
E-3:NOISY Background noise is too loud. Try running “AUTO SETUP” in a quiet
—
environment.
E-4:NO MIC The optimizer microphone was unplugged Connect the supplied optimizer microphone
during the “AUTO SETUP” procedure. to OPTIMIZER MIC jack on the front 24
panel.
E-5:USER CANCEL The “AUTO SETUP” procedure was Run “AUTO SETUP” again.
24
cancelled due to user activity.
See
Warning message Cause Remedy
page
W-1:OUT OF PHASE Speaker polarity is not correct. This Check the speaker connections for proper
message may appear depending on the polarity (+ or –).
12
speakers even when the speakers are
connected correctly.
W-2:OVER 24m (80ft) The distance between the nearest speaker Bring the speaker closer to the listening
and the furthest speaker is out of adjustable position. —
range.
W-3:LEVEL ERROR The difference of volume level among If “SWFR:TOO LOUD” or “SWFR:TOO
speakers is excessive. (No level correction LOW” appears, adjust the output volume of 24
is made.) the subwoofer.
INFORMATION
ADDITIONAL
Readjust the speaker installation so that all
speakers are set in locations with similar —
conditions.
Notes
• If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “AUTO SETUP” again.
• If a warning message “W-1” appears, corrections are made, but they may not be optimal.
• If a warning message “W-2” or “W-3” appears, no corrections are made.
• If an error message “E-6” occurs repeatedly, please contact a qualified Yamaha service center.
English
65 En
Downloaded from www.Manualslib.com manuals search engine
Troubleshooting
■ USB
See
Problem Cause Remedy
page
The music files and The music files and directories are placed Place music files and directories in the FAT area.
—
directories in the USB in locations other than the FAT area.
device cannot be
viewed. You are attempting to browse directory Modify the data structure on your USB device.
hierarchies of over 8 levels or a directory —
with more than 500 files.
The USB device The connected USB device is other than a This unit can recognize only a USB mass storage
cannot be recognized. USB mass storage class USB memory class USB memory device (except USB hard disk
device or USB portable audio player. drives) or USB portable audio player. Also note that it 43
cannot recognize certain USB devices even when they
are devices as described above.
“Disconnected” is This unit recognized the USB device as an Turn this unit off then on again.
displayed even when illegal device.
21
a USB device is
present.
See
Status message Cause Remedy
page
Disconnected Your USB memory device or USB Check the connection between this unit and your
portable audio player has been USB memory device or USB portable audio player.
—
disconnected from the USB port of this
unit.
There is a problem with the signal path Turn off this unit and reconnect your USB memory
from your USB memory device or USB device or USB portable audio player to the USB port 43
portable audio player to this unit. of this unit.
Access error This unit cannot access your USB Try another USB memory device or USB portable
memory device or USB portable audio audio player. —
player.
There is a problem with the signal path Turn off this unit and reconnect your USB memory
from your USB memory device or USB device or USB portable audio player to the USB port 43
portable audio player to this unit. of this unit.
Unable to play No varied data is detected. Try another USB memory device or USB portable
—
audio player.
66 En
Downloaded from www.Manualslib.com manuals search engine
Troubleshooting
■ Remote control
See
Problem Cause Remedy
page
The remote control Wrong distance or angle. The remote control functions within a maximum
does not work nor range of 6 m (20 ft) and no more than 30 degrees off- 23
function properly. axis from the front panel.
INFORMATION
ADDITIONAL
display.
67 En
Downloaded from www.Manualslib.com manuals search engine
Glossary
Glossary
■ Audio information DTS Digital Surround
DTS digital surround was developed to replace the analog
Dolby Digital
soundtracks of movies with a 5.1-channel digital sound
Dolby Digital is a digital surround sound system that gives track, and is now rapidly gaining popularity in movie
you completely independent multi-channel audio. With 3 theaters around the world. DTS, Inc. has developed a
front channels (front L/R and center), and 2 surround home theater system so that you can enjoy the depth of
stereo channels, Dolby Digital provides 5 full-range audio sound and natural spatial representation of DTS digital
channels. With an additional channel especially for bass surround in your home. This system produces practically
effects, called LFE (Low Frequency Effect), the system distortion-free 5.1-channel sound (technically, left, right
has a total of 5.1-channels (LFE is counted as 0.1 and center channels, 2 surround channels, plus an LFE 0.1
channel). By using 2-channel stereo for the surround channel as a subwoofer, for a total of 5.1-channels).
speakers, more accurate moving sound effects and
surround sound environment are possible than with Dolby LFE 0.1 channel
Surround. The wide dynamic range from maximum to This channel reproduces low-frequency bass signals. The
minimum volume reproduced by the 5 full-range channels frequency range of this channel is from 20 Hz to 120 Hz.
and the precise sound orientation generated using digital This channel is counted as 0.1 because it only enforces a
sound processing provide listeners with unprecedented low-frequency range compared to the full-range
excitement and realism. With this unit, any sound reproduced by the other 5 channels in Dolby Digital or
environment from monaural up to a 5.1-channel DTS 5.1-channel systems.
configuration can be freely selected for your enjoyment.
PCM (Linear PCM)
Dolby Pro Logic II Linear PCM is a signal format under which an analog
Dolby Pro Logic II is an improved technique used to audio signal is digitized, recorded and transmitted without
decode vast numbers of existing Dolby Surround sources. using any compression. This is used as a method of
This new technology enables a discrete 5-channel recording CDs and DVD audio. The PCM system uses a
playback with 2 front left and right channels, 1 center technique for sampling the size of the analog signal per
channel, and 2 surround left and right channels instead of very small unit of time. Standing for “Pulse Code
only 1 surround channel for conventional Pro Logic Modulation”, the analog signal is encoded as pulses and
technology. There are three modes available: “Music then modulated for recording.
mode” for music sources, “Movie mode” for movie
Sampling frequency and number of quantized
sources and “Game mode” for game sources.
bits
Dolby Surround When digitizing an analog audio signal, the number of
Dolby Surround uses a 4-channel analog recording system times the signal is sampled per second is called the
to reproduce realistic and dynamic sound effects: 2 front sampling frequency, while the degree of fineness when
left and right channels (stereo), a center channel for dialog converting the sound level into a numeric value is called
(monaural), and a surround channel for special sound the number of quantized bits. The range of rates that can
effects (monaural). The surround channel reproduces be played back is determined based on the sampling rate,
sound within a narrow frequency range. Dolby Surround is while the dynamic range representing the sound level
widely used with nearly all video tapes and laser discs, difference is determined by the number of quantized bits.
and in many TV and cable broadcasts as well. The Dolby In principle, the higher the sampling frequency, the wider
Pro Logic decoder built into this unit employs a digital the range of frequencies that can be played back, and the
signal processing system that automatically stabilizes the higher the number of quantized bits, the more finely the
volume on each channel to enhance moving sound effects sound level can be reproduced.
and directionality.
68 En
Downloaded from www.Manualslib.com manuals search engine
Glossary
INFORMATION
reproduced more faithfully with this system because each
ADDITIONAL
of these signals is independent. The component signal is ■ WAV
also called the “color difference signal” because the Windows standard audio file format, which defines the
luminance signal is subtracted from the color signal. A method of recording the digital data obtained by
monitor with component input jacks is required in order to converting audio signals. It does not specify the
output component signals. compression (coding) method so a desired compression
method can be used with it. By default, it is compatible
Composite video signal with the PCM method (no compression) and some
With the composite video signal system, the video signal compression methods including the ADPCM method.
is composed of three basic elements of a video picture:
color, brightness and synchronization data. A composite ■ WMA
video jack on a video component transmits these three An audio compression method developed by Microsoft
elements combined. Corporation. It employs the irreversible compression
method, which achieves a high compression rate by
thinning out the data of hardly audible part to the human
ears. It is said to be capable of compressing the data
quantity by about 1/22 (64 kbps) while maintaining a
similar audio quality to music CD.
English
69 En
Downloaded from www.Manualslib.com manuals search engine
Specifications
Specifications
AUDIO SECTION VIDEO SECTION
• Minimum RMS Output Power for Front, Center, Surround • Video Signal Type (Gray back) .............................................. NTSC
1 kHz, 0.9% THD, 8 Ω ...................................................... 100 W
• Signal Level
• Maximum Power for Front, Center, Surround (JEITA) Composite ................................................................. 1 Vp-p/75 Ω
1kHz, 10% THD, 8 Ω ........................................................ 135 W S-video ............................ 1 Vp-p/75 Ω (Y), 0.286 Vp-p/75 Ω (C)
Component ................... 1 Vp-p/75 Ω (Y), 0.7 Vp-p/75 Ω (PB/PR)
• Dynamic Power
(IHF, 8/6/4/2 Ω) ............................................. 110/130/160/180 W • Signal to Noise Ratio ................................................. 50 dB or more
• Dynamic Headroom • Maximum Input Level ........................................... 1.5 Vp-p or more
8 Ω ..................................................................................... 0.41 dB
• Frequency Response (MONITOR OUT)
• Maximum Input Signal Component Signal ................................... 5 Hz to 60 MHz, –3 dB
CD, etc. Effect On, 1 kHz, 0.5% THD .................... 2.0 V or more
• Frequency Response FM SECTION
CD, etc. to Front L/R ............................ 10 Hz to 100 kHz, –3 dB • Tuning Range ..................................................... 87.5 to 107.9 MHz
• Phones Output .......................................................... 400 mV/470 Ω • Power Consumption .................................................. 240 W/320 VA
70 En
Downloaded from www.Manualslib.com manuals search engine
Index
■ Numerics Center width, DIMENSION,
1 SOUND MENU, Manual setup ........ 46 Sound field parameter ......................39 Sound field parameter ..................... 39
2 INPUT MENU, Manual setup .......... 46 CHANNEL, Dimension, Sound field parameter ...... 39
2ch Stereo, Sound field program ......... 37 Input source information ..................35 DIMMER, Display settings ................. 54
3 OPTION MENU ............................... 54 CINEMA DSP indicator, Dimmer, Display settings .................... 54
3 OPTION MENU, Manual setup ....... 47 Front panel display ...........................22 DIRECT STEREO ............................... 34
5ch Stereo, Sound field program ......... 37 COAXIAL IN (1), Direct Stereo ........................................ 34
Input assignment ..............................52 Display settings, Option menu ............ 54
■ A COAXIAL INPUT assignment, Display, Input source information ....... 35
A)DISPLAY SET, Option menu ......... 54 Input assignment ..............................52 DIST .................................................... 25
A)INPUT ASSIGNMENT, COAXIAL INPUT jacks ......................52 DIST, Auto setup result ....................... 25
Input menu ....................................... 52 COMPONENT VIDEO jacks ..............14 DISTANCE ......................................... 25
A)SPEAKER SET, Sound menu ......... 48 COMPONENT VIDEO jacks, DISTANCE, Auto setup ...................... 25
A.DELAY, Audio settings ................... 51 Connection .......................................18 DSP LEVEL,
AC OUTLETS (SWITCHED) ............. 21 COMPONENT VIDEO jacks, Sound field parameter ..................... 39
AC OUTLETS, Rear panel .................. 10 Rear panel ........................................10 DSP level, Sound field parameter ....... 39
AM antenna, Connection ..................... 20 Connect MIC!, DTS decoder prioritize setting,
AM tuning ............................................ 40 Auto setup error message .................64 Decoder mode ................................. 53
Amplifier function OSD display time, Connecting to the HDMI ......................17 DVD player, Connection ..................... 16
Display settings ................................ 54 Connection, AM antenna .....................20 DVD recorder, Connection .................. 16
Audio components, Connection ........... 19 Connection, Audio components ...........19 Dynamic range, Sound menu .............. 51
Audio delay, Audio settings ................. 51 Connection, Cable TV ..........................16
AUDIO jacks ....................................... 14 Connection, CD player .........................19 ■ E
Audio jacks .......................................... 14 Connection, CD recorder .....................19 E)LFE LEVEL, Sound menu .............. 51
AUDIO jacks, Rear panel .................... 10 Connection, E)MULTI CH SET, Input menu .......... 54
AUDIO SELECT ................................. 33 COMPONENT VIDEO jacks ..........18 E-1:NO FRONT SP,
Audio select, Option menu .................. 55 Connection, DVD player ......................16 Auto setup error message ................ 65
Audio settings, Sound menu ................ 51 Connection, DVD recorder ..................16 E-2:NO SURR.SP,
AUTO SETUP ..................................... 24 Connection, FM antenna ......................20 Auto setup error message ................ 65
AUTO SETUP, Error message ............ 64 Connection, MD recorder .....................19 E-3:NOISY,
AUTO: RESULT display, Connection, Auto setup error message ................ 65
Auto setup ........................................ 26 MULTI CH INPUT jacks ................19 E-4:NO MIC,
Automatic preset tuning, Connection, Power cable ......................21 Auto setup error message ................ 65
FM/AM tuning ................................. 41 Connection, S VIDEO jacks ................18 E-5:USER CANCEL,
Auto setup error message ................ 65
INFORMATION
Automatic tuning, FM/AM tuning ....... 40 Connection, Satellite tuner ...................16
ADDITIONAL
Connection, Speaker ............................12 E-6:INTERNAL ERROR,
■ B Connection, Video components ...........16 Auto setup error message ................ 65
B)INPUT RENAME, Input menu ....... 53 Connection, Video monitor ..................16 Effect level, Sound field parameter ..... 39
B)MEMORY GUARD, Controlling a TV, Remote control .......57 ENHANCER indicator,
Option menu .................................... 55 Controlling other components, Front panel display .......................... 22
B)SPEAKER LEVEL, Remote control .................................58 Exchange, Preset station,
Sound menu ..................................... 50 Controlling this unit, FM/AM tuning ................................ 42
Background Video, Remote control .................................57
Multi channel input setup ................ 54 Creating original SCENE templates .....31 ■ F
BGV, Multi channel input setup .......... 54 CROSSOVER, Speaker settings ..........49 F)D. RANGE, Sound menu ................. 51
BITRATE, Crossover, Speaker settings .................49 Factory presets, Advanced setup ......... 60
Input source information ................. 35 CT WIDTH, Sound field parameter .....39 FL SCROLL, Display settings ............ 54
FLAG, Input source information ......... 35
■ C ■ D FM antenna, Connection ..................... 20
C)AUDIO SELECT, Option menu ...... 55 D)CENTER GEQ, Sound menu ...........51 FM tuning ............................................ 40
C)SP DISTANCE, Sound menu .......... 50 D)DECODER MODE, Input menu ......53 FORMAT, Input source information ... 35
C)VOLUME TRIM, Input menu ......... 53 D)PARAM. INI, Option menu .............55 FRONT B speaker setting,
Cable TV, Connection ......................... 16 Decoder mode, Input menu ..................53 Speaker settings ............................... 48
CD player, Connection ........................ 19 Decoder select mode, FRONT B, Speaker settings ................ 48
CD recorder, Connection ..................... 19 Decoder mode ..................................53 Front panel display .............................. 22
CENTER SP, Speaker settings ............ 48 Default setting, Front panel display scroll,
English
Center speaker equalizer, Remote control code ........................59 Display settings ............................... 54
Sound menu ..................................... 51 DIGITAL AUDIO COAXIAL jacks ...14 FRONT SP, Speaker settings .............. 48
Center speaker, Speaker settings ......... 48 DIGITAL AUDIO OPTICAL jacks .....14 Front speakers, Speaker settings .......... 48
DIGITAL INPUT jacks, Rear panel ....10
71 En
Downloaded from www.Manualslib.com manuals search engine
■ G Multi channel input setup, PRESET, Advanced setup ................... 60
G)AUDIO SET, Sound menu .............. 51 Input menu .......................................54 Pro Logic ............................................. 38
Game .................................................... 37 Multi-channel source Pure hi-fi stereo sound ......................... 34
with headphones ..............................38
■ H Multi-information display, ■ R
Hall ....................................................... 37 Front panel display ...........................22 Remote control code default setting .... 59
HDMI ................................................... 15 Music Enh. 2ch, Remote control code setting ................ 59
HDMI jack, HDMI cable plug ............. 15 Sound field program ........................37 Remote control codes ........................... iii
HDMI jacks, Rear panel ...................... 10 Music Enh. 5ch, Remote control codes setting .............. 59
Headphone, Dynamic range ................. 51 Sound field program ........................37 Remote control, Troubleshooting ........ 67
HEADPHONE, MUTE indicator, Rename, SCENE template .................. 31
Low-frequency effect level .............. 51 Front panel display ...........................22 Resetting the system ............................ 67
Headphone, MUTE TYPE, Audio settings ..............51
Low-frequency effect level .............. 51 Muting ..................................................36 ■ S
Headphones indicator, S VIDEO jacks .................................... 14
Front panel display .......................... 22 ■ N S VIDEO jacks, Connection ................ 18
Headphones, use .................................. 36 NIGHT indicator, SAMPLING,
HiFi DSP indicator, Front panel display ...........................22 Input source information ................. 35
Front panel display .......................... 22 Night listening mode ............................35 Satellite tuner, Connection .................. 16
HP, Dynamic range .............................. 51 Number of speakers .............................25 SCENE 1 ............................................... 8
Number of speakers, SCENE 2 ............................................... 8
■ I Auto setup result ..............................25 SCENE 3 ............................................... 8
Infrared window, Remote control ........ 23 SCENE 4 ............................................... 9
INI.VOL., Audio settings .................... 52 ■ O SCENE template selection .................. 28
Initial volume, Audio settings .............. 52 OPTICAL IN (2) ..................................52 Selection, Audio input jack ................. 33
Input assignment, Input menu .............. 52 OPTICAL IN (2), Input assignment ....52 Selection, Preset station,
Input channel and speaker indicators, OPTICAL IN (3), Input assignment ....52 FM/AM tuning ................................ 42
Front panel display .......................... 22 OPTICAL INPUT assignment, Selection, SCENE template ................. 28
Input channel indicators, Input assignment ..............................52 SET MENU ......................................... 46
Front panel display .......................... 22 OPTIMIZER MIC jack, Auto setup .....24 Setting remote control code ................. 59
Input menu, Manual setup ................... 46 Optimizer microphone .........................24 Setting SCENE template input source,
Input rename, Input menu .................... 53 Optimizer microphone, Auto setup ......24 Remote control ................................ 56
Input source indicators, Optimizing speaker setting ...................24 Setting the speaker impedance ............ 13
Front panel display .......................... 22 Option menu, Manual setup .................47 SIGNAL INFO, SET MENU .............. 35
Input source information display ......... 35 OSD SHIFT, Display settings ..............54 SILENT CINEMA .............................. 38
OSD shift, Display settings ..................54 SILENT CINEMA indicator,
■ J OSD-AMP, Display settings ................54 Front panel display .......................... 22
Jazz ....................................................... 37 OSD-SOURCE, Display settings .........54 SIZE ..................................................... 25
Other components controlling SIZE, Auto setup ................................. 25
■ L by remote control .............................58 SLEEP indicator,
LFE indicator, Front panel display ...... 22 Other components controlling, Front panel display .......................... 22
LFE/BASS OUT, Speaker settings ...... 49 Remote control .................................58 Sleep timer ........................................... 36
LFE/Bass out, Speaker settings ........... 49 Sound field programs
Low-frequency effect level, Sound menu ■ P with headphones .............................. 38
51 PANORAMA, Sound menu, Manual setup ................. 46
LVL ...................................................... 25 Sound field parameter ......................39 Source feature OSD display time,
LVL, Auto setup result ........................ 25 Panorama, Sound field parameter ........39 Display settings ............................... 54
Parameter initialization, SP ......................................................... 25
■ M Option menu ....................................55 SP A B indicators,
Manual preset tuning, PCM indicator, Front panel display .....22 Front panel display .......................... 22
FM/AM tuning ................................. 41 PHONES jack ......................................36 SP IMP., Advanced setup .................... 60
MANUAL SETUP, SET MENU ......... 46 Play information display, SP, Auto setup result ........................... 25
Manual setup, SET MENU .................. 46 USB controlling ...............................44 SP, Dynamic range .............................. 51
Manual tuning, FM/AM tuning ........... 40 Playing video sources Speaker distance .................................. 25
MAX VOL., Audio settings ................. 52 in the background .............................36 Speaker distance, Auto setup ............... 25
Maximum volume, Audio settings ....... 52 PLII Game ............................................38 Speaker distance, Auto setup result ..... 25
MD recorder, Connection .................... 19 PLII Movie ...........................................38 Speaker distance, Sound menu ............ 50
Memory guard, Option menu ............... 55 PLII Music ...........................................38 Speaker distances,
Movie Dramatic ................................... 37 Pop/Rock ..............................................37 Speaker distance .............................. 50
Movie Spacious .................................... 37 Power cable, Connection ......................21 Speaker impedance,
MULTI CH INPUT jacks, Preset station exchange, Advanced setup ............................... 60
Connection ....................................... 19 FM/AM tuning .................................42 Speaker level ....................................... 25
MULTI CH INPUT jacks, Preset station selection, Speaker level adjustment ..................... 34
Rear panel ........................................ 10 FM/AM tuning .................................42 Speaker level, Auto setup result .......... 25
72 En
Downloaded from www.Manualslib.com manuals search engine
Speaker level, Sound menu .................. 50 VOLUME level indicator,
Speaker settings, Sound menu ............. 48 Front panel display ...........................22
Speaker size ......................................... 25 Volume Trim, Input menu ....................53
Speaker size, Auto setup ...................... 25
Speaker wiring ..................................... 25 ■ W
Speaker wiring, Auto setup .................. 25 W-1:OUT OF PHASE,
Speaker wiring/volume level, Auto setup error message .................65
Auto setup ........................................ 25 W-2:DISTANCE ERROR,
Speaker, Connection ............................ 12 Auto setup error message .................65
Speaker, Dynamic range ...................... 51 W-3:LEVEL ERROR,
SPEAKER, Auto setup error message .................65
Low-frequency effect level .............. 51 WIRING/LEVEL .................................25
Speaker, WIRING/LEVEL, Auto setup ..............25
Low-frequency effect level .............. 51
SPEAKERS terminals, Rear panel ...... 10 ■ Y
Specifications ....................................... 70 Yamaha Parametric Room Acoustic
STRAIGHT .......................................... 38 Optimizer .........................................24
Straight ................................................. 38 YPAO ...................................................24
SUBWOOFER OUTPUT jack, YPAO (Yamaha Parametric Room
Rear panel ........................................ 10 Acoustic Optimizer) .........................24
SUBWOOFER PHASE, YPAO indicator,
Speaker settings ............................... 49 Front panel display ...........................22
Subwoofer phase, Speaker settings ...... 49
Supplied accessories .............................. 3
■ Z
SUR. L/R SP, Speaker settings ............ 49 Zone B ..................................................33
Surround left/right speakers,
Speaker settings ............................... 49
■ T
Test tone, Center speaker equalizer ..... 51
TEST, Center speaker equalizer .......... 51
Tonal quality adjustment ..................... 34
Troubleshooting ................................... 61
Tuner (FM/AM), Troubleshooting ...... 64
Tuner indicators,
Front panel display .......................... 22
Turning off the power .......................... 21
Turning on the power ........................... 21
INFORMATION
TV controlling by remote control ........ 57
ADDITIONAL
TV controlling, Remote control ........... 57
TV Sports ............................................. 37
■ U
UNIT, Speaker distance ....................... 50
Unit, Speaker distance ......................... 50
Unplug HP!,
Auto setup error message ................ 64
USB memory device using,
USB portable audio player using ..... 43
USB playback operation ...................... 43
USB playback styles ............................ 55
USB, Troubleshooting ......................... 66
■ V
VIDEO AUX jacks, Front panel .......... 20
Video components, Connection ........... 16
VIDEO jacks ........................................ 14
Video jacks .......................................... 14
VIDEO jacks, Rear panel ..................... 10
Video monitor, Connection .................. 16
English
73 En
Downloaded from www.Manualslib.com manuals search engine
Front panel/Face avant
1 2 3 4 5 6 7 8
VOLUME
OPTIMIZER MIC
STANDBY
/ON
EDIT
PRESET/TUNING FM/AM A/B/C/D/E l PRESET/TUNING h MEMORY TUNING AUTO/MAN'L
SCENE
1 2 3 4
9 0 A B C D E F
i
Downloaded from www.Manualslib.com manuals search engine
Remote control/Boîtier de télécommande
C
V-AUX USB
SCENE
E 1 2 3 4
BAND LEVEL
TITLE MENU VOLUME
Q
F
G ENTER R
H
RETURN DISPLAY S
REC
J
l PROG h ENHANCER STRAIGHT
1 2 3 4 T
U
SUR.DECODE NIGHT DIRECT ST.
K 5 6 7 8
APPENDIX
L 9 0 10 ENT
V
W
X
ii
Downloaded from www.Manualslib.com manuals search engine
List of remote control codes
Liste des codes de commande
BELL & HOWELL DANTAX 0217 GEC 0204, 0207, 0211,
TV 0058, 0064 DAYTRON 0060, 0061, 0208 0213, 0217
ACER 0093 BENQ 0051, 0081 DE GRAAF 0210 GELOSO 0208, 0210, 0215
ACME 0207 BEON 0213, 0217 DECCA 0204, 0207, 0213, GENERAL TECHNIC
ACURA 0208 BESTAR 0213 0217 0208
ADA 0255 BINATONE 0207 DESMET 0213, 0217 GENEXXA 0209, 0211, 0213,
ADC 0206 BLACK STAR 0214 DIAMOND 0200 0218
ADMIRAL 0058, 0205, 0206, BLAUPUNKT 0255 DIMENSIA 0057 GIBRALTER 0060
0210, 0211 BLUE SKY 0209, 0218 DIXI 0208, 0213, 0217 GOLDHAND 0200
ADYSON 0200, 0207 BONDSTEC 0214 DTS 0208 GOLDSTAR 0060, 0061, 0127,
AGASHI 0200 BOOTS 0207 DUAL 0207, 0215, 0216 0128, 0200, 0201,
AGAZI 0206 BRADFORD 0062 DUAL-TEC 0207, 0208, 0215 0207, 0208, 0210,
AGB 0204 BRANDT 0216, 0226 DUMONT 0060, 0127, 0205, 0213, 0214, 0215,
AIKO 0127, 0200, 0207, BRIONVEGA 0205, 0213, 0217 0207 0217
0208 BRITANNIA 0200, 0207 DURABRAND 0126 GOODMANS 0171, 0201, 0204,
AIWA 0028, 0139, 0229, BROCKWOOD 0060 DUX 0217 0206, 0208, 0213,
0237 BROKSONIC 0138 DYNATRON 0213, 0217 0217, 0240
AKAI 0059, 0065, 0127, BRUNS 0205 ELBE 0203, 0204, 0212, GPM 0209, 0218
0129, 0130, 0200, BSR 0215 0218 GRAETZ 0211
0204, 0208, 0209, BTC 0209, 0218 ELBE-SHARP 0204 GRANADA 0204, 0207, 0210,
0213, 0217, 0218, BUSH 0177, 0208, 0209, ELCIT 0204, 0205 0213, 0217
0255 0210, 0213, 0215, ELECTRO TECH GRANDIN 0208, 0209, 0217
AKIBA 0209, 0218 0216, 0217, 0218, 0208 GRUNDIG 0128, 0130, 0222,
AKURA 0206, 0209, 0218 0230, 0237 ELECTROBAND 0236, 0255
ALARON 0200 CANDLE 0060, 0061 0059 GRUNPY 0062
ALBA 0200, 0207, 0208, CAPSONIC 0206 ELECTROHOME HALIFAX 0200, 0206, 0207
0209, 0217, 0218 CASCADE 0208 0059, 0060, 0061 HALLMARK 0060, 0061
ALBIRAL 0212 CATHAY 0213, 0217 ELIN 0200, 0207, 0213, HAMPTON 0200, 0207
ALLSTAR 0213 CCE 0127 0217 HANSEATIC 0203, 0207, 0208,
AMPLIVISION CELEBRITY 0059 ELITE 0209, 0213, 0218 0213, 0215, 0217
0207 CENTURION 0213, 0217 ELMAN 0215 HANTAREX 0204, 0208
AMSTRAD 0204, 0206, 0208, CENTURY 0205 ELTA 0200, 0208 HARVARD 0062
0209, 0218 CGE 0214, 0215 EMERSON 0060, 0061, 0062, HCM 0206, 0207, 0208,
AMTRON 0062 CIMLINE 0208, 0218 0064, 0128, 0205 0218
ANAM 0208 CITIZEN 0060, 0061, 0062, ENVISION 0060, 0061 HIFIVOX 0216
ANAM NATIONAL 0064 ERRES 0213, 0217 HIGASHI 0200
0062 CITY 0208 ESA 0080 HINARI 0208, 0209, 0213,
ANGLO 0208 CLARIVOX 0212, 0217 ETRON 0208 0217, 0218
ANITECH 0206, 0208 CLATRONIC 0206, 0207, 0208, EURO-FEEL 0206 HISAWA 0209, 0218
ANSONIC 0203, 0208 0209, 0213, 0214, EUROLINE 0217 HITACHI 0006, 0014, 0015,
AOC 0060, 0061 0218 EUROMAN 0200 0016, 0042, 0060,
APEX 0118, 0122, 0132 CMS 0200 EUROMANN 0206, 0207, 0213 0061, 0095, 0105,
ARC EN CIEL 0216 COLORTYME 0060, 0061 EUROPHON 0200, 0204, 0207, 0127, 0156, 0179,
ARCAM 0200 CONCERTO 0060, 0061 0213, 0215 0180, 0204, 0207,
ARCAM DELTA CONCORDE 0208 FENNER 0208 0210, 0211, 0215,
0207 CONDOR 0200, 0207, 0213 FERGUSON 0212, 0217, 0226 0216, 0251
ARISTONA 0213, 0217 CONTEC 0200, 0207, 0208 FIDELITY 0200, 0207, 0210 HORNYPHON 0213
ASA 0205, 0211 CONTEC/CONY FINLANDIA 0210 HOSHAI 0209, 0218
ASBERG 0213 0062 FINLUX 0204, 0205, 0207, HUANYU 0200, 0207
ASTRA 0208 CONTINENTAL EDISON 0213, 0215, 0217 HYGASHI 0200, 0207
ASUKA 0200, 0206, 0207, 0216 FIRSTLINE 0200, 0207, 0208, HYPER 0200, 0207, 0208,
0209, 0218 COSMEL 0208 0213, 0214 0214, 0215
ATLANTIC 0200, 0207, 0213, CRAIG 0062 FISHER 0064, 0127, 0128, HYPSON 0206, 0207, 0213,
0217 CROSLEY 0205, 0214, 0215 0205, 0207, 0215 0217
ATORI 0208 CROWN 0062, 0063, 0128, FLINT 0213, 0218 ICE 0127, 0200, 0206,
AUDIOSONIC 0207, 0208, 0209, 0208, 0213, 0217 FORMENTI 0200, 0205, 0207, 0207, 0208, 0209,
0213, 0216, 0217, CS ELECTRONICS 0215, 0217 0213, 0218
0218 0200, 0207, 0209, FORMENTI-PHOENIX ICES 0200, 0218
AUDIOTON 0207 0214, 0218 0200 IMA 0062
AUDIOVOX 0062 CTC 0214 FORTRESS 0205 IMPERIAL 0211, 0213, 0214,
AUTOVOX 0205, 0206, 0207 CURTIS MATHES FRONTECH 0206, 0208, 0210, 0215
AWA 0200 0057, 0060, 0061, 0211, 0214 INDIANA 0213, 0217
BAIRD 0216 0064, 0065 FUJITSU 0023, 0024, 0025, INFINITY 0063
BANG & OLUFSEN CXC 0062 0088, 0127 INGELEN 0211
0205 CYBERTRON 0209, 0218 FUNAI 0033, 0034, 0035, INGERSOL 0208
BASIC LINE 0208, 0209, 0213, DAEWOO 0060, 0061, 0120, 0036, 0037, 0062, INNO HIT 0201, 0204, 0207,
0218 0127, 0155, 0193, 0206 0208, 0209, 0213,
BASTIDE 0207 0200, 0207, 0208, FUTURETECH 0062 0217, 0218
BAUR 0217 0213, 0218, 0238 GATEWAY 0094 INNOVATION 0206, 0208
BEKO 0228 DAINICHI 0200, 0209, 0218 GBC 0208, 0215, 0218 INTERBUY 0208, 0214
BELCOR 0060 DANSAI 0200, 0206, 0213, GE 0057, 0060, 0061, INTERFUNK 0205, 0211, 0213,
0217 0122, 0147 0214, 0216, 0217
iii
Downloaded from www.Manualslib.com manuals search engine
INTERNATIONAL MANESTH 0206, 0207, 0213, OSO 0209, 0218 RADIALVA 0218
0200 0217 OSUME 0218 RADIO SHACK
INTERVISION 0206, 0207, 0218 MARANTZ 0060, 0061, 0063, OTTO VERSAND 0064
IRRADIO 0201, 0208, 0209, 0090, 0213, 0217 0204, 0207, 0213, RADIO SHACK/REALISTIC
0213, 0217, 0218 MARELLI 0205 0215, 0216, 0217, 0057, 0060, 0061,
ISUKAI 0209, 0218 MARK 0200, 0213, 0217 0255 0062, 0064
ITC 0207, 0215 MATSUI 0204, 0207, 0208, PAEL 0200, 0207 RADIOLA 0213, 0217
ITS 0200, 0209, 0213, 0210, 0213, 0217 PALLADIUM 0207 RADIOMARELLI
0218 MEDIATOR 0213, 0217 PANAMA 0200, 0206, 0207, 0204, 0205, 0214
ITT 0129, 0208, 0211 MEDION 0206, 0208 0208 RADIOTONE 0213
ITV 0208, 0217 MEGATRON 0061 PANASONIC 0006, 0007, 0063, RCA 0057, 0060, 0061,
JBL 0063 MELECTRONIC 0073, 0074, 0097, 0091, 0133, 0135,
JC PENNEY 0057, 0060, 0061 0200, 0207, 0208, 0110, 0114, 0137, 0147, 0149
JCB 0059 0211, 0213, 0216, 0141, 0151, 0162, REALISTIC 0064
JENSEN 0060, 0061 0217 0165, 0186, 0204, REVOX 0213, 0217
JVC 0017, 0018, 0019, MEMOREX 0058, 0061, 0064, 0211, 0244, 0245, REX 0206, 0210, 0211
0108, 0136, 0153, 0208 0246, 0254 RFT 0203, 0205
0178, 0190, 0213, MEMPHIS 0208 PATHE CINEMA RHAPSODY 0200
0218 METZ 0205 0200, 0203, 0207, R-LINE 0213, 0217
KAISUI 0200, 0207, 0208, MGA 0060, 0061 0212, 0215 ROADSTAR 0206, 0208, 0209,
0209, 0218 MICROMAXX 0206, 0208 PATHE MARCONI 0218, 0237
KAMOSONIC 0207 MICROSTAR 0206, 0208 0212, 0216 ROBOTRON 0205
KAMP 0200, 0207 MINERVA 0204 PAUSA 0208 ROWA 0200
KAPSCH 0211 MINOKA 0213 PERDIO 0200 RTF 0205
KARCHER 0207, 0208, 0212, MITSUBISHI 0006, 0015, 0016, PHILCO 0060, 0061, 0063, SABA 0204, 0205, 0211,
0217 0048, 0060, 0061, 0128, 0205, 0214, 0216
KAWASHO 0059, 0060, 0061, 0104, 0112, 0113, 0215 SACCS 0212
0200 0125, 0205, 0213 PHILHARMONIC SAISHO 0204, 0206, 0207,
KENDO 0128, 0210 MIVAR 0200, 0201, 0202, 0207 0208
KENNEDY 0215 0203, 0204, 0207 PHILIPS 0040, 0060, 0063, SALORA 0201, 0204, 0210,
KENWOOD 0060, 0061 MONTGOMERY WARD 0072, 0115, 0116, 0211, 0215
KINGSLEY 0200, 0207 0058 0124, 0130, 0150, SAMBERS 0204
KLOSS NOVABEAM MTC 0060, 0061, 0128, 0175, 0184, 0187, SAMPO 0060, 0061, 0083,
0062 0200 0205, 0207, 0213, 0101
KNEISSEL 0203 MULTI SYSTEM 0215, 0217, 0220, SAMSUNG 0029, 0030, 0031,
KOLSTER 0213 0217 0221, 0232, 0233, 0032, 0044, 0045,
KONKA 0209, 0218 MULTITECH 0062, 0127, 0128, 0252, 0253 0046, 0047, 0060,
KORPEL 0213, 0217 0200, 0207, 0208, PHILIPS MAGNAVOX 0061, 0065, 0068,
KORTING 0205 0210, 0214, 0215, 0124 0069, 0071, 0079,
KOYODA 0208 0217 PHOENIX 0200, 0205, 0213, 0087, 0127, 0128,
KTV 0062, 0127, 0207 MURPHY 0200, 0207 0217 0130, 0144, 0160,
KYOTO 0200, 0212 NAD 0061 PHONOLA 0200, 0205, 0213, 0161, 0170, 0176,
LENCO 0208 NAONIS 0210 0217 0183, 0185, 0200,
LENOIR 0207, 0208 NEC 0026, 0053, 0060, PILOT 0060 0201, 0206, 0207,
LESA 0214 0061, 0096, 0127 PIONEER 0012, 0013, 0060, 0208, 0213, 0217,
LEYCO 0206, 0213, 0217 NECKERMANN 0061, 0098, 0109, 0239, 0241, 0242,
LG 0016, 0038, 0039, 0205, 0207, 0210, 0117, 0128, 0181, 0243
0127, 0128, 0157, 0213, 0217, 0255 0182, 0194, 0195, SANDRA 0200, 0207
0158, 0163, 0164, NEI 0213, 0217 0211, 0213, 0216, SANSUI 0123, 0126, 0213
0166, 0188, 0189, NESCO 0214 0217, 0250 SANYO 0020, 0021, 0022,
0200, 0201, 0207, NET-TV 0082, 0101 PLANTRON 0206, 0213 0049, 0060, 0064,
0208, 0210, 0213, NEW TECH 0208, 0213 POLAROID 0075 0127, 0128, 0200,
0214, 0215, 0217 NEW WORLD 0209, 0218 POPPY 0208 0203, 0207, 0215
LIESENK 0217 NICAMAGIC 0200, 0207 PORTLAND 0060, 0061 SBR 0217
LIFE 0206, 0208 NIKKAI 0200, 0206, 0207, PRANDONI-PRINCE SCHAUB LORENTZ
LIFETEC 0206, 0208, 0218 0209, 0213, 0217, 0204, 0210 0211
LOEWE 0063, 0128, 0203, 0218 PRECISION 0207 SCHNEIDER 0207, 0209, 0213,
0204, 0223, 0227 NIKKO 0061 PRIMA 0208, 0211 0215, 0216, 0217,
LOEWE OPTA 0205, 0213, 0217 NOBLIKO 0200, 0207 PROFEX 0208 0218
APPENDIX
iv
Downloaded from www.Manualslib.com manuals search engine
SHARP 0009, 0010, 0011, TEXET 0200, 0207 APEX 0132, 2049 AKIBA 1050
0060, 0061, 0066, THOMSON 0191, 0192, 0207, BROKSONIC 0138, 2060 AKURA 1043, 1050
0070, 0087, 0111, 0213, 0216, 0226 BUSH 0230, 2112 ALBA 1044, 1050
0143, 0145, 0167, THORN 0212, 0217 JVC 0136, 2053 AMERICAN HIGH
0168, 0169, 0198, TMK 0060, 0061 PANASONIC 0137, 2054, 0254, 1004
0204, 0224, 0247, TOKAI 0213 2110 AMSTRAD 1042
0248, 0249 TOKYO 0200, 0207 RCA 0133, 0135, 2050, ANITECH 1050
SHOGUN 0060 TOSHIBA 0027, 0043, 0053, 2051 ASA 1045, 1046
SIAREM 0204, 0205, 0215 0054, 0064, 0078, SYLVANIA 0134, 2052 ASHA 1002, 1014
SICATEL 0212 0089, 0090, 0106, THOMSON 0226, 2109 ASUKA 1042, 1045, 1046,
SIEMENS 0255 0107, 0127, 0131, TOSHIBA 0131, 2048, 0231, 1050
SIERRA 0213 0140, 0146, 0159, 2111 AUDIO DYNAMICS
SIGNATURE 0058 0197, 0225, 0231, 1000
SILVA 0200 0237 AUDIOVOX 1003
SINGER 0205, 0214, 0215 TOWADA 0211, 0215 TV/DVD/VCR COMBO BAIRD 1042, 1043, 1047
SINUDYNE 0204, 0205, 0215, TRANSTEC 0200 PANASONIC 0141, 1040, 2057 BASIC LINE 1044, 1050
0217 TRIDENT 0204 SAMSUNG 0241, 1070, 2113 BAUR 1046
SKANTIC 0211 TRISTAR 0218 SHARP 0143, 1028, 2059 BEAUMARK 1002, 1014
SOLAVOX 0211 TRIUMPH 0204 SYLVANIA 0142, 1041, 2058 BELL & HOWELL
SONOKO 0206, 0207, 0208, UHER 0211, 0213 TOSHIBA 0140, 1029, 2056 1001
0213, 0217 ULTRAVOX 0200, 0205, 0207, BLAUPUNKT 1046, 1048
SONOLOR 0211 0214, 0215 BROKSONIC 1012, 1013
SONTEC 0213, 0217 UNITED 0217 TV/VCR COMBO BUSH 1044, 1050, 1066
SONY 0041, 0059, 0067, UNIVERSUM 0127, 0128, 0129, AIWA 0237, 1066 CALIX 1003
0085, 0086, 0174, 0201, 0206, 0213, BUSH 0237, 1066 CANDLE 1002, 1003
0196, 0199, 0208, 0214, 0215, 0217 DAEWOO 0155, 0238, 1038, CANON 1004
0219, 0234 UNIVOX 0212 1067 CCE 1006
SOUND & VISION VESTEL 0210, 0211, 0213, GE 0147, 1030 CGE 1042, 1043
0209, 0218 0214, 0215, 0217 GOODMANS 0240, 1069 CIMLINE 1044, 1050
SOUNDESIGN 0060, 0061, 0062 VEXA 0208, 0217 GRUNDIG 0236, 1062 CITIZEN 1002, 1003
SOUNDWAVE 0213, 0217 VICTOR 0213 HITACHI 0156, 1039 COLORTYME 1000
SSS 0060, 0062 VIDEOLOGIC 0200 JVC 0153, 1036 COLT 1006
STANDARD 0207, 0208, 0209, VIDEOLOGIQUE MAGNAVOX 0150, 1033 CRAIG 1002, 1003, 1006,
0213, 0218 0200, 0207, 0209, ORION 0235, 1065 1014
STARLIGHT 0217 0218 PANASONIC 0151, 1034 CROWN 1050
STARLITE 0062 VIDEOSAT 0214 PHILIPS 0150, 0232, 0233, CURTIS MATHES
STENWAY 0218 VIDEOSYSTEM 1033, 1062, 1063 1000, 1002, 1004,
STERN 0210, 0211 0213 QUASAR 0152, 1035 1009
SUNKAI 0208, 0218 VIDEOTECHNIC RCA 0149, 1032 CYBERNEX 1002, 1014
SUNWOOD 0208, 0213 0200 ROADSTAR 0237, 1066 DAEWOO 1005, 1038, 1061,
SUPERLA 0200, 0204, 0207 VIDTECH 0060, 0061 SAMSUNG 0144, 0239, 1027, 1067
SUPERTECH 0200 VIEWSONIC 0076, 0077, 0092, 1068 DANSAI 1050
SUPRA 0208 0099, 0172, 0173 SHARP 0145, 1028 DANTAX 1044
SUPREME 0059 VISIOLA 0200, 0207 SONY 0234, 1064 DBX 1000
SUSUMU 0209 VISION 0213 SYLVANIA 0148, 1031 DE GRAAF 1046, 1049
SUTRON 0208 VORTEC 0213, 0217 TATUNG 0237, 1066 DECCA 1042, 1043, 1046
SYDNEY 0200, 0207 VOXSON 0205, 0210, 0211, TOSHIBA 0146, 0237, 1029, DENON 1010
SYLVANIA 0060, 0061, 0063, 0213 1066 DIMENSIA 1009
0080, 0134, 0142, WALTHAM 0207, 0212 ZENITH 0154, 1037 DUAL 1043, 1046
0148 WARDS 0057, 0058, 0060, DUMONT 1042, 1046, 1047,
SYMPHONIC 0062, 0080 0061, 0063 1049
SYSLINE 0217 WATSON 0213, 0217, 0218 DVD/VCR COMBO DYNATECH 1005
SYTONG 0200 WATT RADIO 0200, 0207, 0212, JVC 1017, 1017, 2045, ELECTROHOME
TANDY 0127, 0207, 0209, 0215 2045 1003
0211, 0218 WEGA 0205 LG 1071, 2087 ELECTROPHONIC
TASHIKO 0200, 0207, 0210 WELTBLICK 0213, 0217 PANASONIC 1020, 1072, 2040, 1003
TATUNG 0127, 0204, 0207, WESTON 0215 2105 ELTA 1050
0213, 0217, 0237 WHITE WESTINGHOUSE PHILIPS 1025, 2046 EMERSON 1003, 1004, 1005,
TCM 0206, 0208 0008, 0200, 0207, RCA 1022, 2042 1012, 1013
TEAC 0127 0217 SAMSUNG 1021, 1021, 2041, ETZUKO 1050
TEC 0207, 0208, 0214, WINCOM 0055, 0056 2104 FERGUSON 1043
0215 YAMAHA 0000, 0001, 0002, SHARP 1023, 1073, 2043, FIDELITY 1042
TECHWOOD 0060, 0061 0003, 0005, 0060, 2106 FINLANDIA 1046, 1047, 1049
TEKNIKA 0058, 0060, 0061, 0061 SONY 1019, 1074, 2039, FINLUX 1042, 1043, 1046,
0062 YAMISHI 0218 2107 1047, 1049
TELEAVIA 0216 YOKO 0200, 0206, 0207, TOSHIBA 1024, 1075, 2044, FIRST LINE 1044, 1045, 1049,
TELECOR 0218 0208, 0209, 0213, 2108 1050
TELEFUNKEN 0217, 0218 ZENITH 1026, 2047 FISHER 1001, 1047
0065, 0213, 0216 YORX 0209, 0218 FLINT 1044
TELEGAZI 0218 ZANUSSI 0210 FORMENTI/PHOENIX
TELETECH 0208, 0214, 0217 ZENITH 0058, 0060, 0100, VCR 1046
TELETON 0207 0105, 0119, 0121, ADMIRAL 1008, 1013 FUJI 1004
TELEVIDEON 0200 0154 ADVENTURA FUJITSU 1042
TENSAI 0208, 0209, 0213, 1005 FUNAI 1005, 1042
0218 AIWA 1005, 1042, 1043, GALAXY 1042
TESMET 0213 TV/DVD COMBO 1044, 1066 GARRARD 1005
TEVION 0206, 0208 AIWA 0139, 2055 AKAI 1007, 1043 GBC 1050
v
Downloaded from www.Manualslib.com manuals search engine
GE 1002, 1004, 1009, MARANTZ 1000, 1001, 1004, PYE 1046, 1056 TELEFUNKEN
1014, 1030 1046, 1051 QUARTER 1001 1043
GEC 1046 MARTA 1003 QUARTZ 1001, 1047 TENOSAL 1050
GELOSO 1050 MATSUI 1044, 1045 QUASAR 1004, 1035 TENSAI 1042, 1045, 1050
GENERAL TECHNIC MATSUSHITA 1004 QUELLE 1042, 1046, 1047 TEVION 1044, 1048
1044, 1048 MEDIATOR 1046 RADIO SHACK THOMSON 1043, 1058
GO VIDEO 1014 MEDION 1044, 1048 1003 THORN 1043, 1047
GOLDHAND 1050 MEI 1004 RADIO SHACK/REALISTIC TMK 1002, 1014
GOLDSTAR 1000, 1003, 1042, MEMOREX 1001, 1002, 1003, 1001, 1002, 1003, TOKAI 1045, 1050
1045 1004, 1005, 1008, 1004, 1005, 1008 TONSAI 1050
GOODMANS 1042, 1045, 1050, 1013, 1014, 1042, RADIOLA 1046 TOSHIBA 1013, 1024, 1029,
1069 1045, 1047 RADIX 1003 1043, 1046, 1066,
GRADIENTE 1005 MEMPHIS 1050 RANDEX 1003 1075
GRAETZ 1043, 1047 METZ 1048 RCA 1002, 1004, 1009, TOTEVISION 1002, 1003, 1014
GRANADA 1046, 1047, 1049 MGA 1014 1010, 1014, 1015, TOWADA 1050
GRANDIN 1042, 1045, 1050 MGN TECHNOLOGY 1022, 1032 TOWIKA 1050
GRUNDIG 1046, 1050, 1062 1002, 1014 REALISTIC 1001, 1002, 1003, UHER 1045
HANSEATIC 1045, 1046 MICROMAXX 1044, 1048 1004, 1005, 1008 UNITECH 1002, 1014
HARLEY DAVIDSON MICROSTAR 1044, 1048 REX 1043 UNIVERSUM 1042, 1045, 1046
1005 MIGROS 1042 RFT 1046 VECTOR RESEARCH
HARMAN/KARDON MINOLTA 1010 ROADSTAR 1045, 1050, 1066 1000
1000 MITSUBISHI 1011, 1042, 1046 SABA 1043 VIDEO CONCEPTS
HARWOOD 1006 MONTGOMERY WARD SAISHO 1044, 1050 1000
HCM 1050 1008 SALORA 1047 VIDEON 1044, 1048
HEADQUARTER MOTOROLA 1004, 1008 SAMSUNG 1002, 1014, 1021, VIDEOSONIC 1002, 1014
1001 MTC 1002, 1014 1027, 1052, 1068, WARDS 1002, 1003, 1004,
HINARI 1044, 1050 MULTITECH 1002, 1005, 1006, 1070 1005, 1006, 1008,
HISAWA 1044 1042, 1046, 1050 SANKY 1008 1010, 1014
HITACHI 1007, 1010, 1039, MURPHY 1042 SANSUI 1007, 1011, 1013, WELTBLICK 1045
1042, 1043, 1046, NATIONAL 1048 1043 WHITE WESTINGHOUSE
1049 NEC 1000, 1001, 1007, SANYO 1001, 1002, 1014, 1013
HUGHES NETWORK SYSTEMS 1011, 1043, 1051 1047 XR-1000 1004, 1005, 1006
1010 NECKERMANN SBR 1046 YAMAHA 1000, 1001, 1007
HYPSON 1044, 1050 1043, 1046 SCHAUB LORENZ YAMISHI 1050
IMPERIAL 1042 NEI 1046 1042, 1043, 1047 YOKAN 1050
INNO HIT 1046, 1050 NESCO 1050 SCHNEIDER 1042, 1044, 1045, YOKO 1045, 1050
INNOVATION 1044, 1048 NIKKO 1003 1046, 1050 ZENITH 1013, 1026, 1037
INSTANT REPLAY NOBLEX 1002, 1014 SCOTT 1012
1004 NOKIA 1043, 1047 SEARS 1001, 1003, 1004,
INTERBUY 1045 NORDMENDE 1010 DVD
INTERFUNK 1046, 1047 1043 SEG 1050 ACOUSTIC SOLUTIONS
INTERVISION 1042 OCEANIC 1042, 1043 SEI-SINUDYNE 2078
IRRADIO 1045, 1050 OKANO 1044 1046 AIWA 2055, 2100
ITT 1043, 1047 OLYMPUS 1004 SELECO 1043 AKAI 2096
ITV 1045 OPTIMUS 1003, 1008 SENTRON 1050 AKURA 2076
JC PENNEY 1000, 1001, 1002, ORION 1012, 1013, 1044, SHARP 1008, 1023, 1028, ALBA 2078, 2086
1003, 1004, 1006 1065 1053, 1073 APEX 2027, 2049
JCL 1004 ORSON 1042 SHINTOM 1006, 1047, 1050 AWA 2078
JENSEN 1007 OSAKI 1042, 1045, 1050 SHIVAKI 1045 AXION 2078
JVC 1000, 1001, 1007, OTTO VERSAND SHOGUN 1002, 1014 BRAINWAVE 2096
1011, 1017, 1036, 1046 SIEMENS 1045, 1047 BRANDT 2073, 2085
1043 PALLADIUM 1043, 1045, 1050 SIGNATURE 2000 BROKSONIC 2060
KAISUI 1050 PANASONIC 1004, 1020, 1034, 1008 BUSH 2075, 2078, 2112
KARCHER 1046 1040, 1048, 1054, SILVA 1045 CENTREX 2077
KENDO 1044 1072 SINGER 1004, 1006 CLASSIC 2078
KENWOOD 1000, 1001, 1007, PATHE MARCONI SINUDYNE 1046 CLATRONIC 2075
1011, 1043 1043 SONTEC 1045 COBY 2078
KLH 1006 PENNEY 1010, 1014 SONY 1016, 1019, 1055, C-TECH 2074
KODAK 1003, 1004 PENTAX 1010, 1049 1060, 1064, 1074 CYBERHOME
APPENDIX
KORPEL 1050 PERDIO 1042 STS 1004, 1010 2025, 2079, 2091
LEYCO 1050 PHILCO 1004, 1051 SUNKAI 1044 DAEWOO 2092, 2098
LG 1003, 1042, 1045, PHILIPS 1004, 1025, 1033, SUNSTAR 1042 DANSAI 2096
1071 1046, 1056, 1057, SUNTRONIC 1042 DAYTEK 2080, 2089
LIFETEC 1044, 1048 1059, 1062, 1063 SUNWOOD 1050 DEC 2075
LLOYD'S 1005 PHILIPS MAGNAVOX SYLVANIA 1004, 1005, 1031, DENON 2030, 2102, 2103
LOEWE 1048 1018 1041 DENVER 2075, 2076
LOEWE OPTA 1045, 1046 PHONOLA 1046 SYMPHONIC 1005 DIAMOND 2074
LOGIK 1006, 1050 PILOT 1003 TAISHO 1044 DK DIGITAL 2094
LUXOR 1047 PIONEER 1011, 1046 TANDY 1001 DUAL 2078
LXI 1003 PRINZ 1042 TASHIKO 1003, 1042 D-VISION 2096
M ELECTRONIC PROFEX 1050 TATUNG 1007, 1042, 1043, DVX 2074
1042 PROFITRONIC 1046, 1066 ELTA 2096
MAGNASONIC 1014 TCM 1044, 1048 EUROLINE 2096
1047 PROLINE 1042 TEAC 1005, 1007 FUNAI 2052, 2058
MAGNAVOX 1004, 1018, 1033 PROSCAN 1009 TECHNICS 1004, 1048 GLOBAL SOLUTIONS
MAGNIN 1003, 1014 PROSONIC 1044 TEKNIKA 1003, 1004, 1005 2074
MANESTH 1050 PROTEC 1006 TELEAVIA 1043
vi
Downloaded from www.Manualslib.com manuals search engine
GLOBAL SPHERE SANSUI 2074 TOSHIBA 2068 PANASONIC 2015, 2016, 2017,
2074 SANYO 2095 2120
GOODMANS 2075, 2077, 2078 SCANMAGIC 2078 PHILIPS 2117, 2121, 2123,
GRUNDIG 2077, 2098 SCIENTIFIC LABS DVD/LD COMBO 2128
H&B 2075 2074 PIONEER 2012, 2013, 2014
HAAZ 2074 SCOTT 2088 PIONEER 2036 PROSCAN 2129
HE 2078 SEG 2074, 2086 RCA 2116, 2124, 2129,
HITACHI 2032, 2072 SHARP 2034, 2043, 2059, DVD RECORDER 2133
HOME ELECTRONICS 2093, 2106 APEX 2024 REPLAYTV 2118, 2119, 2120
2078 SILVA 2076 JVC 2070 SHARP 2009, 2010
INNOVATION 2072 SINGER 2074 LG 2071 SONIC BLUE 2119, 2120
RX-V561
IRRADIO 2134 SKYMASTER 2074, 2078 PANASONIC 2020, 2065, 2066, SONY 2005, 2006, 2007,
JDB 2078 SKYWORTH 2076 2067 2122, 2130, 2131,
JVC 2033, 2045, 2053, SM ELECTRONIC PHILIPS 2019, 2061, 2062, 2132
2073, 2099 2074, 2078 2063 STACK 9 2132
KENWOOD 2030, 2097 SONY 2028, 2029, 2039, PIONEER 2021 SYSTEMAX 2132
KINGAVON 2075 2083, 2107 RCA 2018 TAGAR SYSTEMS
KODA 2075 SOUNDMASTER SONY 2022, 2064 2132
LAWSON 2074 2074 TOSHIBA 2068 TIVO 2116, 2121, 2122,
LENCO 2075 SOUNDMAX 2074 YAMAHA 2023 2123, 2130, 2131
LG 2084, 2087 STANDARD 2074 YUKAI 2069 TOSHIBA 2004, 2125, 2132
LIFETEC 2072 STAR CLUSTER TOUCH 2132
LIMIT 2074 2074 ULTIMATETV 2133
LOGICLAB 2074 STARMEDIA 2075 VIEWSONIC 2132
LUXOR 2077 SUPERVISION
DVR VOODOO 2132
MAGNAVOX 2037, 2073, 2075 2074, 2078 ABS 2132 YAMAHA 2011
MAGNUM 2072 SYLVANIA 2052, 2058 ALIENWARE 2132 ZT GROUP 2132
MBO 2078 SYNN 2074 CYBERPOWER
MEDION 2072 TCM 2072 2132
MICROMAXX TEAC 2074 DELL 2132
DIRECTV 2123, 2128, 2129,
LD PLAYER
2072 TEC 2076
MICROMEDIA TECHNICS 2030 2133 YAMAHA 2002
2073 TECHNIKA 2096 DISH NETWORK
MICROSTAR 2072 TECHNOSONIC 2126, 2127
MITSUBISHI 2035 2096 DISHPRO 2126 CD PLAYER
MIZUDA 2075 TEVION 2072, 2074 ECHOSTAR 2126, 2127 YAMAHA 5000, 5013
MUSTEK 2078 THOMSON 2085, 2109 EXPRESSVU 2126
NAIKO 2077 TOKAI 2076 GATEWAY 2132
ONKYO 2073, 2135 TOSHIBA 2026, 2044, 2048, GOI 2126
ORAVA 2075 2056, 2073, 2108, HEWLETT PACKARD CD RECORDER
P&B 2075 2111 2132 YAMAHA 5001
PACIFIC 2074 UNITED 2078 HITACHI 2008
PANASONIC 2030, 2040, 2054, VOXSON 2078 HOWARD COMPUTERS
2057, 2105, 2110 WHARFEDALE 2132 MD
PHILIPS 2019, 2026, 2046, 2074 HTS 2126
HUGHES 2123, 2128 YAMAHA 5002, 5003, 5004
2073, 2081, 2090 XLOGIC 2074
PIONEER 2036, 2082 YAKUMO 2077 HUMAX 2123
PROLINE 2077 YAMADA 2077 HUSH 2132
PROVISION 2075 YAMAHA 2000, 2001, 2003, IBUYPOWER 2132 TAPE DECK
RCA 2031, 2042, 2050, 2030, 2101 JVC 2126, 2127 YAMAHA 5005, 5006
2051 YUKAI 2078 LINKSYS 2132
RED STAR 2076 ZENITH 2038, 2047, 2073 MEDIA CENTER PC
REOC 2074 2132
MICROSOFT 2132
TUNER
ROADSTAR 2075, 2078, 2086
ROWA 2077 MIND 2132 YAMAHA 5007, 5008, 5009,
DVD-DVR NIVEUS MEDIA 5010, 5012, 5014
SABA 2085
SABAKI 2074 PANASONIC 2067 2132
SAMSUNG 2032, 2041, 2104, PIONEER 2114 NORTHGATE 2132
2113 SAMSUNG 2115
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA Printed in China WK65610
RX-V561
The circled numbers and alphabets correspond to those in the Owner’s Manual.
Les nombres et lettres dans un cercle correspondent à ceux du mode d’emploi.
1 2 3 4 5 6 7 8
OPTIMIZER MIC
STANDBY
/ON
EDIT
PRESET/TUNING FM/AM A/B/C/D/E l PRESET/TUNING h MEMORY TUNING AUTO/MAN'L
SCENE
1 2 3 4
9 0 A B C D E F
■ Remote control/Boîtier de télécommande
C
V-AUX USB
SCENE
E 1 2 3 4
BAND LEVEL
TITLE MENU VOLUME
Q
F
G ENTER R
H
RETURN DISPLAY S
REC
J
l PROG h ENHANCER STRAIGHT
1 2 3 4 T
U
SUR.DECODE NIGHT DIRECT ST.
K 5 6 7 8
L 9 0 10 ENT
V
W
X