BOSTIK SEAL ‘N’ FLEX® ONE PLUS P590

®
SEAL ‘N’ FLEX
ONE PLUS P590
LOW MODULUS POLYURETHANE SEALANT
®
5th October 2021
SEAL N FLEX
ONE PLUS P590
YOUR SMART ADVANTAGES Product codes
300ml cartridge/ 20 per carton
 Low modulus
Grey 30619339
 +100%/-50% joint movement
White 30619347

 Bubble free curing
LOW MODULUS POLYURETHANE
Black
SEALANT
Extremely elastic, > 1,000% elongation at break
30619336
 Sag free, easy tooling 600ml sausages/ 20 per carton
®
EAL N FLEX
 Excellent durability
Grey 30619340
 UV resistant
 Paintable* White 30619348
 Made in Australia Black 30619337

USES
ONE PLUS P590
Bostik Seal ‘N’ Flex® One Plus P590 is a low modulus,
Limestone
Sandstone
Off-white
30619341
30619346
30619342
bubble free curing, universal polyurethane sealant for
LOW MODULUS POLYURETHANE SEALANT
construction and expansion joints. When cured it will Epping Grey 30619338
form a tough and flexible seal capable of cyclic
expansion and compression movement of +100%/-50%.
Bostik Seal ‘N’ Flex One Plus P590 can be used on:
TYPICAL PERFORMANCE DATA (approx.)
 Insitu concrete and render
 Precast and tilt up panels Temperature resistance -30 to 80°C
 Aluminum Composite Materials
Skin time 90 minutes
 EIFS/ETICS
 Metal Cladding
Cure rate 3mm/24 hours on
 Brickwork and block work
@ 23°C/50%RH porous substrates
 Plasterboard face and paper lined recessed edges
 Fibre cement sheet Full cure 7 days on porous
 Aluminium windows
substrates. Allow 14
 Granite, sandstone and marble
days in joints over
 GRC, fiberglass and mostly specialty panel systems
20mm wide.

CERTIFICATIONS Specific gravity 1.30 g/ml

 ASTM C920
 ASTM C1248 Shore A hardness >25
 F-EXT-INT-CC 25LM: EN 15651-1 for Façade Joints
 EMICODE EC1 100% Modulus 0.30 N/mm2
 SNJF F25E
Tensile strength 1.20 N/mm²

Elongation at break > 1000%

PRODUCT CHARACTERISTICS
Total joint movement + 100% / -50%
Viscosity Non-sag, smooth
thixotropic paste Maximum joint width Up to 80mm

Cure method Moisture curing

Application temperature 5 to 40°C

Bostik Australia Pty Ltd, Level 1, 6 English Street, Essendon Fields, Victoria, 3041, Australia. www.bostik.com/au
Version 2

Page 1 of 3
 BOSTIK SEAL ‘N’ FLEX® ONE PLUS P590

DIRECTIONS FOR USE 3. Use the trigger to extrude the sealant. To stop; depress
Read and understand the Safety Data Sheet before using the catch plate.
this product. SDS can be acquired by visiting
www.bostik.com.au. Apply Bostik Seal ‘N’ Flex One Plus P590 in a continuous
operation using enough pressure to properly fill the joint.
SURFACE PREPARATION Tool off the surface of the sealant with an appropriate
1. Application temperature + 5°C to + 40°C (applies to sized spatula or trowel. Apply sufficient pressure to leave
environment and substrates) a smooth, consistent surface and ensure maximum
2. Clean and dry all surfaces by removing foreign matter contact with the interface of the joint
and contaminants such as laitance oil, dust, grease,
frost, water, dirt, old sealants, curing agents and any JOINT SEALING
protective coating A joint with the correct dimensions is able to absorb
3. Dust and loose particles should be vacuum cleaned. movements between building materials. Always use a
backing rod for correct sealant geometry and contact
PRIMING with the substrate.
Bostik Seal ’N’ Flex One Plus P590 adheres perfectly - Prime after the installation of backing rod
without the use of a primer to most porous & non-porous - Ensure maximum adhesion to the bond face
substrates. Always test adhesion prior to application. - Minimum allowable joint depth is 5mm
- Maximum allowable joint width is 80mm
IMPORTANT: For optimum adhesion and in areas of
- Tool sealant to achieve concave shape
critical, high performance applications such as high stress
joints, extreme weather exposure or surfaces that are
too porous, the use of substrate primer is required.

Porous substrates:
1. Absorbent or porous substrates will allow a bead of
water to easily soak into and wet out the surface of the
substrate
2. For maximum performance on porous surfaces and in
all periodically immersed and submerged applications,
use Bostik N49 Primer (refer to the Bostik N49 Primer
Technical Data Sheet)
3. Porous substrates not subject to immersion or ponded Joint Width to Depth ratio:
water e.g. vertical expansion joints in concrete or
masonry structures will not require priming if clean, dry Width Depth
and uncontaminated
Min 5mm to 10mm 1:1 ratio

Non-porous substrates: i.e. A 10mm width will require

1. Non-absorbent substrates will cause a bead of water to 10mm depth
be retained on the surface of the substrate as a raised 𝑾𝒊𝒅𝒕𝒉 (𝒎𝒎)
droplet. The droplet does not easily soak into the >10mm, up to 80mm Depth (mm) = +𝟔
𝟑
surface of the substrate.
2. Bostik N40 Primer is recommended for non-porous i.e. A 16mm joint width will
plastic and metal substrates e.g. u-PVC outlets and pipe require a 12mm depth:
work, brass, copper fittings, stainless steel trays and 16
flashings (refer to the Bostik N40 Primer Technical Data
Depth (mm) = +6 = 12mm
3
Sheet).
3. Prime plastics and metallic non-porous substrates with
Bostik N40 Primer using the two-cloth method
described in the Bostik N40 Primer Technical Data Sheet
COVERAGE
APPLICATION The estimated lineal metre yield per pack size is
Bostik Seal ‘N’ Flex One Plus P590 should be dispensed recommended in the following table. No allowance has
from either the cartridge or sausage by means of a been made for waste or irregular joint geometry.
caulking gun.
Joint 5mm x 10mm x 20mm x 50mm x
Cartridge application: (W x D) 5mm 10mm 10mm 25mm
1. Pierce the membrane at the top of the top of the 300ml Cartridge 12 3 1.5 0.24
cartridge and screw on the nozzle 600ml Sausage 24 6 3 0.48
2. Cut the nozzle to give the required angle and bead size
3. Place the cartridge in a caulking gun and squeeze the W=Joint width (mm). D=Joint depth (mm).
trigger

Sausage application:
1. Clip the end of the sausage and place in a barrel gun
2. Screw the end cap and nozzle onto the barrel gun
Bostik Australia Pty Ltd, Level 1, 6 English Street, Essendon Fields, Victoria, 3041, Australia. www.bostik.com/au
Version 2

Page 2 of 3
 BOSTIK SEAL ‘N’ FLEX® ONE PLUS P590

CLEANING STORAGE AND SHELF LIFE

Clean off uncured material, hands and equipment Store in cool (between 5°C to 25°C) dry, well- ventilated
immediately after use using Bostik Handy Wipe towels. area out of direct sunlight. Shelf life is 15 months from
Cured material can be removed by mechanical means production date in original unopened packaging and
only. correct storage conditions.

PAINTABILITY VOC INFORMATION

Bostik Seal ‘N’ Flex One Plus P590 can be painted after a 2.8 g/L
minimum of 7 days. Coatings containing solvents such as
enamels, oil based or other coatings may cause the
surface of the sealant to react creating a tacky surface.
Surface coatings may discolour in direct contact with
cured Bostik Seal ‘N’ Flex One Plus P590. Surface coatings
may crack and craze as a result of cyclical movement of BOSTIK HOTLINE
supporting sealant joint. A field test is recommended to
ensure compatibility of any coating with Bostik Seal ‘N’ Smart help 1800 267 845
Flex One Plus P590.

LIMITATIONS
Not recommended for:
- Use in chlorinated water such as swimming pools,
spas, etc.
- PE, PP, PC, PMMA, PTFE, soft plastics, neoprene and
bituminous substrates
- Constantly immersed salt water
- Use for glazing applications
- Application to cement based substrates within 28
days of initial pour or set
- Use in trafficable joints
- Applied in temperatures below 5°C or above 40°C
- Exposure to water and/or alcohol before it has
completely cured
- Applied to joints less than 5mm in width and depth
- Applied on joints larger than 80mm
- Bostik Seal N Flex One Plus White may yellow on the
surface if exposed to strong natural or artificial UV
light for prolonged periods of time.

As all substrates and conditions are different, it is

strongly recommended that the applicator, or end user
conducts their own tests and ensure the product meets
their own end use requirements

This datasheet is for the general help of users. It is provided in good faith. The data is current and accurate to the best of our knowledge. Differing
materials, substrates, environments, site conditions, and product storage, handling and application may affect results. Users should carry out
tests to decide the product’s suitability for purpose. This data sheet and the properties of the product may change without notice. Users,
suppliers and retailers should check that the data sheets they have are the latest. To the maximum extent permitted by law, Bostik disclaims all
warranties in relation to manufacture and use of the product. Bostikis not liable for representations made by users, suppliers or retailers about
the product. Bostik is not liable for any loss or damage resulting from incorrect, careless, or negligent use or storage of the product, including use
of out of date product. Any liability arising from use of the product is limited to the replacement or purchase price of the product. Bostik does not
exclude rights and remedies that cannot be excluded by legislation, for example under the Australian Consumer Law (ACL). Sale of the product by
Bostik is subject to the Bostik Australia Proprietary Limited Conditions and Terms of Sale. For more information on Bostik, products, and
conditions of use and sale visit www.bostik.com/au

Bostik Australia Pty Ltd, Level 1, 6 English Street, Essendon Fields, Victoria, 3041, Australia. www.bostik.com/au
Version 2

Page 3 of 3