ALL GSM FAQ

QUESTION ANSWER

Can you list me the interfaces of a

Air, Abis, Ater, A, Gb, Gi, Gn, Gd, Gr, Gs
GSM network?
Can you list me the network elements MS, BTS, BSC, MSC, SGSN,
of a GSM network? GGSN,BG,HLR,EIR,AUC,CG,LIG
Unique Identifier for a SIM.1 MS can be paged with a single
What is the IMSI?
PAGING message
What is the TMSI? TMSI in a Location Area. Shorter so you can page more MS
When do you use IMSI and when Authentication, but basically we care about it for paging.
TMSI? Paging message always contains IMSI
How many MS can you page with 1
2
paging message done w/ IMSI?
How many MS can you page with 1
4
paging message done w/ TIMSI?
Paging method? Can you change this Either IMSI and / or TMSI … you can change the method by
method w/ BSS parameters? NSS parameters
RACH, AGCH, PCH … there is also NCH but it is not used
Name some of the CCH channels
…
Which are the feature we have in ----- Default PCH has always priority over AGCH. Anyway you
in order to change the CCCH can reserve a certain number of blocks of AGCH. However, if
behaviour? AGCH =0, AGCH has priority over PCH
Which are the CCCH in UL and which
UL = RACH DL = AGCH, PCH, (NCH)
are in DL?
Dedicated Channels in GSM FACCH, SACCH, SDCCH, TCH

Broadcast Channels in GSM BCCH, FCH, CBCH, SCH

Which is the difference between Congestion = all resources in use. BLOCKING = Blocked
CONGESTION and BLOCKING? requests
How do you measure CONGESTION
seconds
in -----?
How do you measure BLOCKING in
events
-----?
Which is the unit of measure for the
1 event
blocking measurement?
Which is the measurement period for
10 msec
the congestion measurement?
Which is the measurement period for
20 sec
the traffic measurement?
 Which are the ----- features to help
SDCCH congestion not to become Dynamic SDCCH, FACCH Call Set Up
SDCCH blocking?
HR (EFR and AMR), DR, DADLB (actually this one avoids
Which are the ----- features to help congestion to happen as well as traffic reason handover),
TCH blocking? traffic reason HO (MSC initiated), AMH (traffic reason HO,
BSC initiated)
DR is triggered when there is actual congestion in the TCHs.
Which is the difference between
DADLB is triggered when the load of the BTS is above a
DADLB and DR?
certain threshold defined as a parameter.

Which type of HO is triggered w/ DR? SDCCH - TCH HO

Is DR helpful for SDCCH or TCH
TCH Congestion
congestion?

There are 2 timers and 1 threshold you Min Time = Time in order to identify neighbours.
need to define when you activate DR Max Time = max time to try HO.
… can you tell me which are these Level Threshold = Minimum Threshold of the neighbours in
parameters and what are these for? order to try SDCCH-TCH HO

Which are the differences between DR Basically IDR is an improvement of DR and it takes into
(directed Retry) and IDR (Intelligent account the Source Call Type, Target Cell Type and
Directed Retry)? Subscriber type … anyway it is never used …
Threshold Level
Which are the DR parameters you need
Min time DR
to set?
Max Time DR
Basically when the BTS load is above the load defined by a
parameter (in AMH feature's parameter group). the
Can you briefly explain to me the BSC
AmhPBGT MARGIN for that specific neighbour relation is
INITIATED TRAFFIC HO?
squeezed in order to help to lower load traffic … that's the
reason why you call it TRAFFIC HO
What happen in a network if there are
They just use C1 (it happens all the time in Europe)
legacy MS that don't support C2?
Microcell and to bias a layer (it happens in CINGULAR for
Why do you want to use C2? 850 in order to have dual band MS which are EDGE capable
only on 850)
Can you make practical examples of C2
traffic management in dualband, microcell
usage?
What's the difference between Cell Cell Selection is when you switch on the MS. Cell
Selection and Cell Re-Selection? ReSelection when it is already on
- MS is able to read BCCH
What are the 4 criteria of the suitable - MS is allowed to register to the PLMN and LA
cells for MS to camp on - the cell is not barred
- signal level is higher than threshold (C1 > 0)

What is the TIMING ADVANCE? Measure distance MS -BTS w/ resolution of 550 meters

How long is it in time and in space? 1/2 bit where the bit rate is 270kbps ~ 550 meters

Who calculates it? BSC/BTS and sends back to the MS

 How is it calculated? RACH delay
How can you collect TA statistics in the There is the table … although we have only 10 bins … not 63
----- OSS? …
Can you modify the setting of the TA
Yes, BSC level, maximum is 10 bins
stats in the ----- OSS?
BTS needs to know when MS signal is expected to arrive to
Why do we need to use timing advance
avoid inter symbol interference
Max distance you can keep a call in
GSM?
(what is the maximum value of timing 63 TA .. Equivalent to ~ 35 km
advance in normal GSM cell? And
what does it equivalent to? )
Which network element uses TA to Basically MS sends its bursts in advance in order to get to the
take certain decisions? MS or BTS? BTS in the window expected …
Alows to have double maximum distance MS - BTS …
What is the extended cell feature?
theoretically 70 km … practically 65 km
Is it available in -----? Yes …

Which is the cabinet / BSC you need to

Ultrasite will support it in S11.5. Talk Family supports it
have in order to make Extended Cell
since S7
work?
Advantages and disadvantages of the
Basically when you have a MASTER, if this goes down also
MASTER-MASTER and MASTER-
the other cabinet goes down
SLAVE configuration

Do you need the Synch Cable between

no
cabinets in order to share the T1?

Which is the best configuration for

cabinet synchronization (MASTER,
independent
SLAVE, INDEPENDENT) if you don't
have CBCCH?
Why independent configuration is the Because doesn't have a chain effec in case 1 BCF has
best? problems
Advantages and disadvantages of
Basically a hybrid configuration is always an headache for
allocating 1900 radios on one cabinet
implementation
and 850 on another cabinet
Briefly explain FULL and SUB FULL is when you don't use DTX, SUB when you use DTX.
measurements in the Air I/F? FULL Is measured on 104 frames, SUB on 12 frames
Are these stats always sent? Both of
Yes., both all the the time
them?
How can the BSC understand which
There is a flag that says if DTX is used or not
one to use?
If you plot these stats what do you
Sub stats are more spread, more standard deviation
notice?
What happens when you enable UL
DTX / disable UL DTX to your RxQual has more samples in 0 and 7
RxQuality?
How much of it is due to real Some is real interference but most is just statistical
interference? distribution
Why you have a different distribution
between SUB and FULL RxQual
Less samples = Less reliable = More deviation
samples? (HINT - It is a statistical
reason)

What are BER and BEP? Bit Error Rate and Probability
Can you explain what is NBLO It is used in CBCCH and it measures the difference between
measurement and how it is used? BCCH and non-BCCH layer
CBCCH advantage = Trunking Gain + you can assign the call
to the slave (e.g. other layer) w/ call assignment w/o using
Which is the main advantage of HO
CBCCH Vs. Multiple BCCH? MBCCH advantage = Give BCCH channel to both bands …
especially here in US where there are a lot of legacy phones in
singleband @ 1900
Could you please explain the basic
signalling of a Mobile Originated Call RACH, AGCH, SDCCH, TCH …
Setup?
Could you please explain the basic
signalling of a Mobile Terminated Call PCH, RACH, AGCH, SDCCH, TCH …
Setup?
What are the important GSM
3.22, 4 series esp. 4.08 & 4.60, 5 series esp 5.08, 5.05
specifications for radio performance?
What is the channel spacing in GSM? 200 kHz
What is the duplex frequency of
45 MHz for GSM850 and 80 MHz for GSM1900
GSm850 and GSM1900?
in GSM, What is the multiple access
FDMA/TDMA with FDD
and duplex used?
Absolure Radio Frequency Channel Number. Basically it is
What is ARFCN? What does it mean?
the frequency in use.
Is ARFCN = 120 in GSM850 or
850
GSM1900 band?
How many ARFCN do you have in
ch 128 -251 (124 Ch)
GSM850?
How many ARFCN do you have in
Ch 512 - 811 (300 ch)
GSM1900?
Which is the number of frames in a
51
SIGNALLING CHANNEL?
Which is the number of frames in a
26
TRAFFIC CHANNEL?
What's the difference between
MECHANICAL and ELECTRICAL Electrical reduces also side lobes and back lobes.
DOWNTILT?
How does the ELECTRICAL Put a signal w/ different phases which deletes part of the
DOWNTILT work? initial one creating smaller lobes
What is the difference in propagation
7 dB. The higher the frequency, the more the loss.
between 850Mhz and 1900Mhz?
Also known as shadowing, caused by large obstructions such
What is Slow fading? as hils, building trees. Behaviour is a slow change in
propagation
 Also known as multipath or Rayleigh. Caused by constuctive
or destructive interference as a result of reflections, multiple
What is Fast fading?
propagation paths. Fades as deep as 30 dB over distances of
half a wavelength
In the slow moving mobile
environment,
Fast Fading.
what kind of fading has more impact to
signal?

When the RF signal is distorted around an object. Happens to

all EM waves, it seems as though the wave "bends" around an
object, therefore can provide coverage behind an obstruction.
What is Diffraction?
Happens when there is no LOS or the 1st Fresnel zone is
obstructed. Commonly modelled as knife edge, either single
or double. Epstein-Petersein is a multiple edge model.

What is the effect of transmit frequency

None. Diffraction is independent of frequency
on Diffraction?
Coverage is provided by the signal propagating to an area.
What is the difference between
Service is useable coverage, affected by interference or GSM
"Service" and "Coverage"?
distance constraints
Interference is unwanted coverage. The same signal can be
What is the relationship between
both coverage or interference depending on whether the signal
Coverage and Interference?
is useful or not
Site location (Lat, long), Antenna configuration (diversity,
What is the required information from HPBW, gain, type), Antenna line information (feeder
site survey activities? And what are length/loss, spiltter, diplexer, MHA), Rooftop layout.
their purpose? This is used for link budge calc., coverage planning and
prediction simulation, optimization analysis

Customer wants to give to ----- a new

service, coverage planning of a new
market. You need to tell him which are Coverage Polygons (Rural, SubUrban, Urban, Freeway) #
the inputs you need in order to start Different RxLevel for each polygon # Coverage Probability
your work. Please do so … which are
the inputs you need to ask him for.

What is the Coverage Probability? You

have normally 2 Coverage Probabillity Cell Edge. Cell Area.
… which are their names?
Cell Area Coverage Probability ~ 90% is a typical value you
Which is a typical Coverge Probability
can use and that you have to put in the Propagation model as
you can use for coverage dimensioning
an input in order to have the Cell Range and from that the
purposes?
Cell Area.
The customer has given you the input
you have requested him (Polygons, 1. You need to decide the type of equipment and
RxLev, Coverage Probability) now you configuration you want to have. Normally this is a standard
need to decide which are the tools you one (e.g. ULTRASITE, w/ LNA, 2 TRXs) 2. Calculate the
need in order to give him an initial LINK BALANCE for that specific configuration. 3.
understanding of how many sites he Propagation Model (e.g. Okomura Hata) correction factors
needs. Please tell me which are the (e.g. mean and standarddeviation)
tools you need
 Probably at this point you have to
decide / ask which is the typical
PRO OMNI = Trunking Gain. Cover perfectly an Island for
configuration you want in the sites
example, from the top of a hill. CONS OMNI = Painful when
(omni, 2 sectors, 3 sectors). Which are
you need to make frequency plan and/or limit interference
the advantages / disadvantages of
OMNI?
Probably at this point you have to
decide / ask which is the typical
configuration you want in the sites Probably you can use a 2 sector site when you have a freeway
(omni, 2 sectors, 3 sectors). Which are in a rural area.
the advantages / disadvantages of 2
sectors?
Probably at this point you have to
decide / ask which is the typical
3 sectors is probably the best combination for coverage and
configuration you want in the sites
frequency plan and it gives good ability to control
(omni, 2 sectors, 3 sectors). Which are
interference (w/ tilts)
the advantages / disadvantages of 3
sectors?
Related to the previous question …
which is the best configuration is you City = 3 sectors. Freeway = 2 sectors (but only if around there
have to cover a freeway? And if you is really nothing else to cover). Island = Omni works just fine
need to cover an Island? And if you if you put it on the top of the hill
need to cover a city?
Once you have decided which is the
sector configuration to use, how can
you use the Cell Range calculated w/ You use the typical hexagon model. With that you know how
the Propagation Model correction many sites you need in order to cover you polygon.
factors in order to calculate how many
sites to you need?
10*log (W) = dBW,
What is the relationship of W, dB and 10*log(W/1000[mW]) = dBm,
dBm? 10 log (Power/ Reference) = dB or 20 log (Voltage /
Reference)

10 dB + 14 dB 24 dB

10 dBm + 14 dB 24 dBm

In order to do it you need to convert the dBm to Watt, sum the

10 dBm + 14 dBm Watts and go back to dBm … in this case the results is 15.455
dBm

Is the following statement correct? False. The A and B coefficient used in OH model is different
Okumura Hata model used in GSM850 if frequency below 1000 MHz and above1500MHz. Besides,
is the same as GSM1900. the area correction factor is different between the 2 frequency

BTS type (Rx sensitivity and Tx Power), Antenna gain, feeder

What is the possible way to improve
length and types (site planning), using MHA and diversity
link budget?
(improve Rx), using Booster (improve Tx)
Sensitivity and TRX output power for
-112 to -115 dBm, 5W TRX
----- METROSITE?
 -115 typical (-112 to -118 dBm),
Sensitivity and TRX output power for
43dBm (guaranteed ~ minimum on 100% production)
----- ULTRASITE?
47dBm TRX (nominal ~ on 90% of production)
With the maximum allow pathloss from link budget with
consideration of LP, STD, Slow fading margin and
How does the link budget impact to
propagation model , it is used for defining the cell range. If
number of the sites required in an area?
the pathloss is bigger, the cell range could be higher and the
number of sites require will be reduced.

cell/site splitting: coverage enhancement but more cost to

hardware & limitation of frequency
more TRX: easy but need frequency
micro cell layer: more easy to control interference but more
Please list 3 methods of capacity site require
enhancement and their pros & cons dualband: additional spectrum required, minimize impact to
existing band coverage/capacity,
soft capacity features: hopping, IUO, DFCA, AMR, DTX
better cell planning &optimization for better interference
control.

Basically the LNA is helping to improve the effective noise

figure of the receiving path which then reduces the Rx
How does LNA improve the Sensitivity of receiving path. The simple way to do is the
sensitivity? compensation of feeder loss (but not more than LNA gain).
However, the calculation have to be calculated on the
effective noise figure and effective gain of the receiving path.

IDD is basically a DL booster. The way it works is basically

INTELLIGENT DOWNLINK
putting together the signals of 2 TRXs with the same signal
DIVERSITY?
but w/ a different phase. The gain is ~ 3 dB.
What is the problems with highrise lack of coverage as the antennas are lower down. Increased
buildings? interference from LOS to many sites.
TRUNKING GAIN IS THE GAIN THAT YOU HAVE
WHEN YOU HAVE LESS ENTRY POINT TO THE
What is trunking gain? RESOURCES (e.g. 1 line in front of the 10 airport check-in
counters works much better than 10 lines in front of the same
10 airport check-in counters) …
One channel used for 3600 seconds in 1 h ~ 100% utilization
what does 1 Erlang mean?
of a resource (TCH or PDCH in GSM)
Customer is complaining that w/ 1TRX
he can serve only 3 Erlang and has 10%
Basically the traffic is not approaching the BTS w/ a Poisson
blocking while we have told him that
distribution (which is the assumption that is the base of the
according to the Erlang B table we
Erlang B model)
should be able to serve 3 Erl w/ 2%
blocking. What is happening?

What is the Erlang C table? It is a model which takes into account queuing
If we have QUEUING active do we
No … because queue is not infinite …
need to use the Erlang C table? Why?
Is the Erlang B table the right model to
NO
use in case of AMR FR / HR?
1 TRX w/ 2% blocking … according to
the Erlang B table how many Erlang ~ 3 Erl
can I serve?

What is the output from link budget? Maximum allowed pathloss (UL and DL)
Which is a typical PathLoss you can
~ 150 dB
have in a GSM connection?
Do we use different LINK BUDGET No, maximum allowed path loss is not environment
for different type of environments? dependent. It is service dependent though
To model the network. Allows the planner to see the effect of
What is the purpose of a radio planning making changes to the network so the best solution can be
tool? chosen and implemented. Can also be used to store all the site
data.

First start with accurate clutter, DTM and building data. Next
How can you ensure the planning tool
calibrate the model correctly. All site data must be correct.
is as accurate as possible?
This will give the propagation model of the network.

What general power law do

3.5 power law (4th power law good enough)
propagation models follow?
Name two methods of propagation
Statistical and Deterministic (Ray tracing, virtual source)
modelling
Name two statistical models commonly Okumra-Hata (General propagation) and Walfisch-Ikegami
used (canyon like environment)
Collect CW (not TEMS, noise floor isn't low enough)
measurements from mulitple locations. Drive through as
many clutter classes as possible. Input all data to a planning
How do you calibrate a statistical tool. Calculate SD. Use different values of first co-efficient to
propagation model? get different SD values. This is normally a square function, so
get minimum. Continue with other coefficients. Repeat.
Coefficient order: distance, diffraction, BTS height, BTS
height*distance

What are the main MML families in EA: Adjacency, EE: BSC, EQ: BTS, ER: TRX, EH: HOC,
manipulating radio objects? EU: POC

How do you list current alarms for a

ZEOL
BTS?

What does the initial "Z" stand for in an It makes MML interpret the command from the main level,
MML command? even if you are inside another family

What is the available tool for OSS data

TANO, NDW, EOSFLEX
collection in -----?

Name two drive test tools TEMS, NEMO(TOM)

What drive test equipment is needed for Logging tool, 2 phones (one short call, one long), GPS,
performance data collection? scanner, map, power supply for all
What type of measurements should be Continuous Wave (CW), Greater dynamic range and lower
used for model calibration? noise floor
 Name some protocol analysers for
Nethawk, K1215, Agilent
monitoring the Abis, A or Gn interfaces

When a cell is being interfered with by another cell with the

What is co-channel interference
same carrier frequency
What is the GSM rejection ratio for co-
9 dB
channel interference?
When a cell is being interfered with by another cell with a
carrier frequency which is seperated by 200kHz for the 1st
What is adjacent channel interference?
adjacent interferer, 400kHz for the 2nd adjacent interferer,
etc.

What is the GSM rejection ratio for the

-9 dB (-18 dB for the second adjacent interferer)
first adjacent channel interference?

What is frequency reuse 4/12 ? There are 12 frequency ch reuse on the 4x3-sector sites.

When planning a frequency what is the

3 ch. (600 kHz) for GSM850 and 4 ch (800 kHz) for
channel separation required for the
GSM1900
TRX in the same cell?
When planning a frequency what is the
channel separation required for the 400 kHz
TRX in the same site?
1/1: there is 1 MA list and reuse on every cells
3/3: there are 3 MA list and each site (3 sectors) using same
what is the different between hopping
MA list and reuse every 3 sites
scheme 1/1, 3/3, 1/3?
1/3: there are 3 MA list and each cells in same site using
different MA list. And reuse same pattern for every site.
Number of TRX (too small number of TRX cannot gain much
What is the factor to determine which
from BB hopping) and combiner type. (RTC is only can use
hopping scheme above to be used?
BB hopping)
Do we need to plan MAIO Step, MA
There is no need to plan for MAIO and MAIO offset in BB
List, MAIO Offset and HSN when use
hopping. However, HSN is required.
BB hopping?
Do we need to plan MAIO Step, MA yes, all of them. MA list is required to plan to ensure that
List, MAIO Offset and HSN when use there is no frequency collision within the site. HSN should be
RF hopping? same for all sectors in the sites.
Do you have MAL only w/ RF hopping
only with RF hopping
or also w/ BB hopping?
Which is the main difference between RF = TRX changes ARFCN. BB = Call moves from 1 RTSL
RF and BB hopping? to an other (in an other TRX)
What is a MAL? Mobile Alloction List. It is used for RF HOPPING
How many MAL can you define in a
128
----- BSC?
Which are the parameters you need t
define in the BTS when you want to HSN, Maio Step, MAIO Offset,hopping mode, MAlist
use a MAL?
Why do we use Frequency Hopping? (I You have 2 advantages w/frequency hopping …
mean which are the advantages of FREQUENCY DIVERSITY (FADING) and
frequency hopping) INTERFERENCE DIVERSITY
 Which is the type of fading you are
able to "beat" when you use Fast Fading
HOPPING?
You have a BTS w/ 3 hopping TRXs
Basically the sum of MAIO OFFSET and MAIO STEPS
and a MAL w/ 3 ARFCN … once you
exceeds the number of ARFCN in the MAL … it is indeed a
try to unlock the the site the BSC gaves
silly problem but you need to know it. Suggestion is to keep
you a DX error saying that you don't
MAIO OFFSET = 0 and MAIO STEP =1 in such a case
have enough frequencies … where is
(where probably you are using ad HOC hopping)
the problem?

How many HSN do we have? 64 (0 … 63)

Is this a GSM standard or do you know

if ----- has any plan to increase this No. it can't … it is GSM specs
number?

How does HSN = 0 works? sequential hopping (others are psuedo-random)

Uses the parameters you set (MAIOs) and FN which is

Do you know which are the basics of
something you can't define … that is the reason why in a
the algorithm used from HSN?
synch network you can better control the interference.
How many HSN do I need to define for
1
each BTS in RF HOPPING?
How many HSN do I need to define for
2
each BTS in BB HOPPING?
Effective Frequency Load. A way of measuring spectral
What is EFL? efficiency with a hopping system. Formula:
erls/(#freq*ave#(TCH/TRX))
A way of measuring how effectively the spectrum is being
What is spectral efficiency? used. The more traffic carried with less spectrum the more
efficient the use. Formula: erls/MHz/Cell
Is the following statement correct?
Why? No, because it is all frequencies are used all the time which
It is good enough to use RF hopping could create the high interference level esp. if the site
reuse 1/1 with MA list length 15 in the planning (dominant area) is not good enough.
area with 6+6+6 BTS.
When customer want to build
GSM1900 on GSM850 site or vise
Frequency use (intereference and intermodulation between 2
versa, what are the things that you
bands)
would like to suggest him to check and
antenna solution (Isolation requirement and area spacing)
what is the issue behind that? (not
parameters)
When can you have paging thru the Gb
Gs interface is necessary
I/f instead of the A I/f?
What's the advantage of the paging thru
Can page a MS in data session
the Gb I/f?
Yes … if the LA is bigger you need to page more MS, so all
Does the Abis I/f size change the
these messages need to go thru the Abis … so you need a
paging capability?
bigger Abis
How many MS can you paging
100,000 paging messages … 200,000 MS if you use IMSI or
messages can you send in 1 hour w/
400,000 MS if you use TMSI
16kbps TRXSig?
 How many MS can you paging
messages can you send in 1 hour w/ 400,000 paging messages …
64kbps TRXSig?
Which is a parameter you can change in
order to reduce the probability that a
Periodic Location Update … you need to reduce it …
MS that went out of coverage will be
paged?
Identify neighbour … couple BCCH, BSIC make you identify
Why do we need BSIC in GSM?
the neighbour
How many bits are the BSIC? 6
Which are the 2 components of the
NCC, BCC
BSIC?
They should be the same in the BCCH TRX, not in all the
Which is the relation between BCC and
TRXs … NOKIA by default is usig the same but it is not
TSC?
mandatory in GSM.
Can we have TSC <> BCC in -----?
Since when? Do you know if
Yes, we have a S10 feature about it. CINGULAR doesn't use
CINGULAR has it activated?
it.
(do we have any features that could
allow TSC <> BCC?)
Which is the the reason to have TSC Better HO SUCCESS RATE … but basically it doesn't
<>BCC? change anything …
Which is the relationship between NCC
There is no relationship. PLMN is MCC + MNC
and PLMN?
This is for the MS and BTS to learn the interference.
Basically the MS is expecting a certain TSC but receives an
Why do we need TSC (Training
other if there is intereference. The difference between the
Seuqence Code) in GSM?
expected and the measured one is used in order to reconstruct
the rest of the bits of the burst.
Which is a recommended size for the Depends from Abis LAPD size … 1-2 BSC works fine w/
LA in -----? 16kbps
Can you have smaller LA? YES

Can you have bigger LA? YES

Can you have a LA across 2 different
NO
MSC?
Why do you need the LA in GSM? Paging reasons
Can you have a LA across more than 1
Yes
BSC?
Which is the trade off in the LA size? Paging and SDCCH traffic

Which are the KPI you need to monitor SDCCH, Paging Success Rate, congestion in Abis and Air for
when you are modifying the LA size? LAPD and CCCH

Does roaming traffic affecting the LA

No
size?
 Which are the parameters you can
change in order to make harder or Cell Reselection Hysteresis
easier LA update?
What is the PLMN permitted It defines to which PLMNs the MS is permitted to report
parameter? measurement results.
Is "PLMN permitted" parameter the
No.
same as PLMN id?

What parameters need to be set as the

NCC part of the BSICs.
equal to or subset of PLMN permitted?

If it is not set, what will happen? MS is not possible to measure the cells e.g. no HO.
Where really do you need this
National Borders
parameter?
Do you know which is the PLMN
All of them
setting used in CINGULAR?
Can you use TRAFFICA tool in the
CINGULAR network? Blue? Orange? Only if you have our core … means Orange
Why?
If you increase the LA size do you
NO
expect an increase in the A I/f traffic?
If you increase the LA size do you
expect an increase in the Abis I/f YES
traffic?

If you increase the LA size do you

YES
expect an increase in the Air I/f traffic?

What do you use the FACCH for in UL

HO, CALL SETUP if you have the feature
and DL?
What do you use the SACCH for in UL
System Info (DL), Measurements (UL), SMS during a call
and DL?
How many SDCCH can you put in 1
8
RTSL?
Which is the difference between
combined = CCCH + 4SDCCH; separated = CCCH and
COMBINED and SEPARATED
SDCCH are in different RTSL
signalling?
Which channels have no power
BCCH, SDCCH, GPRS TSL(DL)
control?
Measurement report is sent to BSC
every period of which channel and how SACCH = 480 ms
long does it equivalent to?
What is the different between sync and in non-sync HO, there is physical information is require for
non-sync HO? And in which case it MS to perform HO. The information contains TA information
will happen? And what parameter is and it requires when the cell HO to different BCF cell. The
used to define this? parameter is in each ADJ pair "SYNC"
 is following statement correct?
There is no problem if the neighbor list
False. MS report only BCCH and BSIC to BSC, therefore
contains the same BCCH and same
BSC will not be able to differentiate which ADJ is the right
BSIC from different cells as long as the
one and that could cause HO failure and eventually call drop
2 neighbour are far away and not
interfere to each other.
Nx is the total number of sample in the evaluation.
What is the Nx/Px parameters in
Px is the number of samples within Nx that below or above
handover parameters defined? And
threshold.
what is the impact on setting large
The large number could lead to the longer time for HO
number of Nx/Px?
decision making
HO Attempt is before the check if target has available RTSL.
What's the difference between HO
HO Command is after. There are more HO attempts than HO
ATTEMPT and HO command in -----?
commands
Which is the 1st thing you should check
in the formula when the customer is
If counts HO attempts …
telling yu he has a very high HO failure
rate?

1) Interference (uplink or downlink)

2) Uplink quality
3) Downlink quality
4) Uplink level
5) Downlink level
Please name 5 types of HO reasons 6) Distance between MS and BTS
7) Turn around corner MS (special case of rapid field drop)
8) Any other rapid field drop
9) Fast / slow moving MS (special case of umbrella handover)
10) Any other umbrella or power budget handover
11) traffic reason ho

1) Adjacent Cell Load Threshold : Can be checked only for

cells belonging to the same BSC as the serving one
What is the 4 criteria in ranking the
2) Adjacent Cell Priority
ADJ for HO candidate?
3) Overloaded Cell -> Reduction of Priority
4) RX level (if same priority)
What is typical value use for PBGT HO
6 dB
margin?
dualBandCell Y indicates cell as dual band cell
What are the 3 parameters in BSS that multiCellBandReporting 0..3 number of adjacent dual band
need to change to make sure that cells taken into account for measurement report
dualband is working? earlySendingIndication Y enables MS to send classmark 3
message as early as possible
it reduces the amount of same band reporting. Normally there
What is the impact of setting higher
are only 6 cells report from MS. Deducting by MBR, the rest
number of mulitcellBandreporting?
will be used for same band.
What feature could be used to help the
EMR
situation?
What is the RLT parameter? RLT = Radio Link timeout.
 It is both in UL and in DL. Speaking about UL … if the BTS
doesn't receive the SACCH in UL it decreases this counter by
How does RLT works? -1 and if receives the SACCH it increments by +2. If it gets to
the maximum value it stops incrementing. When it gets to
zero the BSC releases the call.
How many RLT do we have in -----?
In NOKIA we have only one RLT …
UL / DL / AMR FR / AMR HR?
Why should we have different RLT for Because the C/I protection in very different … so the RLT
AMR FR and AMR HR and EFR? should take into account before dropping a call …
What does EFR mean? EFR = Enhanced Full Rate

It is a way to speed up the Power Control + HO decisions

What is FAST AVERAGING? because you don't need to wait the complete window before
start counting Nx/Px in your decision
We have a WEIGHTING parameter in It is used to overweight if you want) the FULL measurements
HOC, POC … what is this for? rather than the SUB measurements
How many parameters do you have for
FAST AVERAGING?
3 … after Call Set Up, After PC, After HO
(at what call phase Fast Averaging can
be applied?)
Because based on the measurements we can take after the
same SACCH different HO decisions and you want to give to
Why do we have the concept of certain HO more priority (e.g. Quality HO should have higher
PRIORITY in the HO? priority over PBGT HO because the problem is more urgent
… and the way you choose the neighbours for the different
HO types are different)

What is a CLEAR CODE? DX Cause w/ failure

What is a DX CAUSE? Why this funny Internal Cause in BSC. Because of DX architecture ofBSC
name? and MSC
After activation of Double BA list the
sector doesn't make anymore HO … Neighbour BCCHs are not in the list
what's the problem?
where to find information about ----- 1) NED 2) Jump page. 3) Database Description for BSC
counter and KPI? Measurements (PDF document)
What is the JUMP PAGE? Intranet page w/ info about KPI, COUNTERS

CLEAR CODES CAN BE MONITORED W/

How can you use DX CAUSE and
OBSERVATIONS … YO CAN FOR EXAMPLE USE
CLEAR CODE in order to optimize my
"DROP CALL OBSERVATION" OR "DROP CALL
network?
BREAKDOWN" …
THEY ARE BOTH WAYS TO GET PERFORMANCE
WHICH IS THE DIFFERENCE
STATS … KPI AND COUNTERS ARE FROM
BETWEEN MEASUREMENT AND
MEASUREMENTS TABLES. OBSERVATION ARE
OBSERVATION
GIVING US CLEAR CODES / DX CAUSE.
Is the MS or the BTS able to measure No … in GSM we can't measure the C/I … we can only
the actual C/I of the Air I/f? measure the BER, FER … which are affected of the C/I
 In the ----- OSS I have seen there are These are idle mode measurements and they are only in UL
interference measurements . Can you … basically in the RTSL not in use if the Level is above -110
explain what they mean and how they dBm we assume it is interference and it is recorded in the
is measured? OSS stats …
INTERFERENCE HO are basically QUALITY HO in good
In the ----- OSS measurements I can RxLevel condition (which is set with a RxLevel parameter)
see HO due to interference? How do … the reason is dual … 1) Have stats about bad Quality in
these HO work / are triggered? good RxLevel conditions. 2) Trigger an intracell HO rather
than a intercell HO

What is AMR? Adaptive Multirate voice coding

AMR varies the proportion of voice coding and channel

How does it work? coding to provide more robustness in bad C/I at the expense
of voice quality
How many AMR codecs are there at 8 at FR, 6 at HR (1 not used in HR). Only 4 can be used in a
FR and HR? call
Mean Opinion Score: A subjective view of the quality of a
What is MOS?
voice call
Frame Erasure Rate: Number of speech frames discarded due
to errors. A better measure of quality than BER with AMR
What is FER?
because BER is measured before decoding and FER after
decoding
What is the effect of AMR on a full rate It allows the call to maintain the same FER in worse C/I
channel? conditions
What is the effect of AMR on a half It allows the FER to improve in better C/I conditions while
rate Channel? occupying half a timeslot
When certain C/I thresholds are met, the voice codec will be
How does AMR link adaptation work? changed. There is no target FER to maintain and thresholds
have to be carefully chosen
A channel with 11.4 kbps. FR is 22.8 kbps. Each channel
What is a half rate channel?
occupies alternate bursts of a multiframe.
With cell load thresholds. When the lower limit is reached,
How does the BSC decide whether to
calls are packed, when the upper limit is reached, new calls
use a HR or FR channel?
are sent to FR

When is a HR unpacked to FR? When the RxQual of the HR call reaches a pre-set limit
Does ----- supports all the GSM AMR No doesn't support HR 7.95kbps because it should use 16kbps
codecs? TRAU and NOKIA doesn't have it.
Name of a CINGULAR idea to maximize capacity. Basically
while testing it they have found that our BSS had a problem
and wasn't unpacking if a candidate for Quality HO wasn't
What is MAXCAP feature?
available. When it was introduced we saw a sudden increase
in drop call during unpacking. That is the reason why we want
to have MAXCAP = OFF.
Do you have more signalling channels
In band singalling, but it is transparent
in AMR HR?
Does the overall bit rate on the Air I/F
No it doesn't …
changes w/ AMR?
 Dynamic Frequency and Channel Allocation, is a BSS radio
resource management functionality that selects the radio
channel individually for each connection from a dedicated
What is DFCA? channel pool based on C/I criteria. The different degrees of
interference tolerence of different connection type such as
EFR,AMR FR, HR are taken into account in the ch selection
process.
-BSC2i + CP2MX CPU cards or BSC 3i
-BSC-BSC connections for BSC using DFCA and have
adjacent service area.
What are the DFCA HW requirement?
-Ultrasite or metrosite BTS
- Wideband combiner
- LMU in every BTS
-S11.5
- CX4.1
What are the DFCA SW requirement?
-OSS4
-LMU4.1
Three frequency bands are defined in
BCCH band, Regular band (optional), DFCA band
DFCA, what are they?
-The range of Malist is 1-32
-The DFCA MA list must be defined the same way in al BSCs
What are the requirement/limitation in within each continous BSC area
DFCA band? -DFCA MA list do not contain consecutive frequency
-Any two DFCA MA lists containing adjacent frequency are
required to be of the same length.

-non real time information I.e. Background inteference matrix

What are the inputs for DFCA channel
-near real time information I.e. Mobile measurement report
allocation?
- realtime information I.e. Radio channel usage information

What are the 4 methods in DFCA C/I

incoming DL, Incoming UL, Outgoing DL, Outgoing UL
estimation?
 Soft Blocking is a user define parameter.

If in the C/I estimation phase any of the four C/I estimates

produced for each radio channel candidate does not exceed
the soft blocking limit of the interfered connection, then the
radio channel candidate is deemed soft blocked.

If there are no acceptable assignment candidates (i.e. all the

candidates breach the connection type specific soft blocking
C/I limit), the assignment will be directed to a regular TRX if
What is the Soft Blocking in DFCA? available.

If there are no free TSLs on any regular TRXs of the cell, the
call will be finally rejected (DFCA soft blocking situation).
Directed retry could still be used and if successfull the
directed retry will move the call to another cell in which case
the call is not rejected.

In case of handovers soft blocking is not applied except if the

handover is for DR or DADLB then the soft blocking is
applied as in normal call setup.

If the current incoming DL C/I average is below the Force HR

mode C/I threshold for the corresponding channel type (non-
AMR/AMR), then the force HO mode is switched on. After
HR mode switched on, HR channel/AMR HR channel will be
What is DFCA forced HR mode? assigned to a speech connection that is placed on a DFCA
TRX until the HR mode switched off.

DFCA Force HR mode C/I threshold and Force HR C/I

threshold AMR are user defined parameters.
· Packet switch territory is not allow in DFCA TRX
What is the restrictions to use DFCA? · Dynamic SDCCH is not allowed in DFCA TRX
(features interworking limitation) · FACCH call setup to DFCA TRX is not possible.
· Antenna hopping cannot be used in DFCA TRX

BSS Synchronization
-Sync MUST be on prior to switching to DFCA Mode.
-FN and TS offsets should be set (not left at 0)
Interference Handovers
-nterference based handovers should be enabled on all DFCA
BTS
Apart from DFCA parameter, what are Dynamic Power Control
the parameters shall be checked for -Should be enabled on all DFCA BTS for UL and DL
DFCA activation? Timeslot Type
-TCH timeslots only supported on DFCA TRX’s
-All signaling (e.g. SDCCH) and GP timeslots must be
removed.
Idle & Active BA List Usage
-BA list must be created and attached for Idle & Active use in
each DFCA BTS
What additional network elements are
SGSN, GGSN, CG, DNS, (BG, LIG)
needed for Data?
What elements need to be upgraded to TRXs. A modulation scheme is used and modulation is
activate EGPRS? performed by the TRX with hardware
How does an MS handover from one It doesn't. MS performs cell re-selection exactly like idle
cell to another during a data session? mode
When a cell re-selects, the data stored in the BVC buffer is
Flushed (Deleted). If the new cell is in the same PCU than the
What is a Flush?
data is moved to the new BVC. If not it is deleted and there is
a bigger break in downloading.
What modulation scheme does GRPS
GMSK
use?
How many GPRS coding schemes are
there currently in ----- and what are CS1, CS2
they called?
What modulation scheme does EGPRS
GMSK(mcs1-4), 8PSK
use?
How many EGPRS coding schemes are
9: MCS1 - MCS9
there?
What is the maximum bitrate per
GPRS: 13kbps with CS2, EGPRS: 59.62 kbps with MCS9
timeslot with GPRS and EGPRS?
Maximum TSL capacity after C/I has reduced the MCS but
What is timeslot capacity?
before TBF multiplexing
Re-transmissions are sent in MCSs of the same family as each
What are the MCS families used for?
family has a different packet length.
What functionality counters fast fading
Incremental Redundency
in EGPRS?
Data is punctured after coding. This involves reducing the
number of bits needed to send the data. 3 puncturing codes are
How does it work? used. If the first packet can't be fully decoded, it is sent again
with different puncturing scheme. The packets are combined
until it is decoded.
What functionality counters slow
Link Adaptation
fading in EGPRS?

PCU tries to keep best throughput by using BEP to calculate

the probabilty of the packet being decoded. PCU uses initial
How does it work? MCS, then once it has BEP values, chooses modulation, then
coding scheme according to whether it is initial transmission
or re-transmission. User only has to set initial MCS

When there is more than one TBF allocated to the same

What is timeslot multiplexing?
timeslot
When there is a mix of GPRS and EGRPS TBFs on a
What is TBF multiplexing?
timeslot. Especially bad with UL GPRS and DL EGRPS
3, NMO1: Needs a Gs link, all CS and PS paging through
SGSN and PCCCH (or CCCH). NMO2: No Gs link, CS
How many different types of Network
paging through MSC and CCCH, PS paging through SGSN
Mode of Operation are they and how
and CCCH, NMO3: No Gs link, CS paging through MSC and
are they different?
SGSN, PS paging through SGSN and PCCCH (not supported
in Nokia)
 Radio Link Control is between the PCU and the MS. Logical
What is the difference between the
Link Control is between the SGSN and the MS. RLC gives
RLC and LLC protocols?
network throughput, LLC gives user throughput.
A territory is an area of the cell that is used for a certain
What is a territory?
purpose
How many are there and what are they
4: CS, Dedicated data, Default data, Additional data
called?
Dedicated data is only used for data, default can be used for
both but CS is kept out of it unless there is no more CS
How does each behave? territory available, additional is data territory beyond default
and is released as soon as possible, CS can be used to carry
CS and includes default and additional
Is there power control in EGPRS? Only in Uplink

EGPRS Dynamic Abis Pool: A part of the Abis set aside for
EGPRS use. It is shared amongst all TRXs attached to it and
What is an EDAP and why is it
provides a 30% saving on Abis capacity compared to fixed
needed?
allocation. The EDAP is needed because the higher bitrates
with EGPRS need more than 1 16kbps Abis subslot

In one phase, the RACH request asks for a TBF. In two phase,
What is the difference between one-
the RACH request ask for a single block and uses this to ask
phase and two-phase access?
for the TBF.
Routing Area: serve the same function for data as the LA for
What is a RA?
voice: Allows the SGSN to page the MS
A RA is a subset of an LA. Maxiumum size is the LA size.
What is its relationship to an LA?
An LA can have more than one RA.
Which is the trade off in the DEFAULT Small default territory = Few GPRS reason Ho. Big default
TERRITORY size? territory = Better Throughput
Can you have separated (from the
VOICE one) signalling for GPRS / Yes, you can although it is not really used
EGPRS?
Which is the channel you are going to
PBCCH
use?
Which is the trade off in term of
Need to use a dedicated RTSL for it
signalling using PBCCH?
What's the impact of GPRS traffic on There is an impact, but there is no evidence so far of any real
the CCCH load? bottleneck created from data signalling
Why we don't we use PBCCH in
Basically Blackberry 1st generation doesn't suport it
CINGULAR?
Which are the other features you can
use for cell reselection if you C31, C32
implement PBCCH?
C31 allows you to prefer a set of BTSs. C32 makes the cell
Which is the meaning of C31 and C32?
reselection among the one prefered from C31

Packet Control Unit. Receives the LLC PDUs from the SGSN
and breaks them down into RLC Packets for the radio
What is a PCU and what does it do?
interface. Vice versa in the opposite direction. Responsible for
all scheduling, LA and radio resource management for data
 2i: 2 per BSCU, 8+1 BCSU max, 3i: 4 per BSCU, 6+1 BCSU
How many are there in a BSC?
max

Digital Signal Processor core. Handles the individual Abis

What is a DSP core?
subslots and does the actual work.

How many are there in a PCU? 16

What is the maximum number of

16
EDAPs a PCU can handle?

What is the maximum number of 16

256
kbps Abis sub-slots a PCU can handle?

As 8PSK has variable amplitude, the amplifier has to work in

What is the effect on the link budget of linear, not satuarated, mode. There has to be a power back-off
using 8PSK modulation? to keep operation in linear mode. Back-off is 2 dB for BTS, 4-
5 dB for MS

Erlang B will provide enough spare TSL to guarentee GoS for

voice. Data can use these. Formula is a choice between Erlang
B and an approximation, which ever requires more timeslots.
Outline a dimensioning method for
Number of TSL for data is data load divided by TSL capacity.
combined voice and data traffic?
Total TSL required given by Max(ErlangB(CS),CS traffic(E)
+Guard TSL+TSL for data-Dedicated TSL)+dedicated TSL.
From here work out TRXs and so on.

A way of including timeslot multiplexing in dimensioning by

What is rate reduction?
taking into account CS and PS traffic and PS territory

How big can an EDAP be? 12 * 64 kbps Abis TSL

How many EDAPs can be attached to a There is no limit. It could be one per site or one per TRX,
site? although this is inefficient

How many EDAPS can be mapped

As long as there is space on the T1, there is no limit
onto a single T1?

Which are the 3 states of a MS in

Ready, Idle, Standby
GPRS?
MS is transmitting data or it has just transmitted data … it is
What does READY mean?
in active mode
What does IDLE mean? Basically the SGSN doesn't know where the MS is
What does STANDBY mean? SGSN knows where the MS is based on the RA resolution
How do you move from IDLE to
Attach and Detach
READY? And viceversa?
How do you move from READY to READY --> STANDBY / timer. STANDBY --> READY just
STANDBY? And viceversa? if you send or receive data
How do you move from STANDBY to
GPRS Detach, either implicit or through a timer
IDLE? And viceversa?
What is a TBF in EGPRS? Temporary Block Flow
Is the TBF in both directions? no, unidirectional
Can the same TBF be bi-directional
no
(let's say like a voice call)?
Which is the basic signalling in order to
UL TBF and in DL just ACK
maintain an UL TBF?
Which is the basic signalling in order to
DL TBF and in UL just ACK
maintain an UL TBF?
What is the effect of putting data on a With no power control there is increase interference to the
hopping TRX? hopping layer
What is the main objective of EGPRS
To maximise user throughput
optimisation?
Mostly through, capacity improvements. C/I improvements
In EGPRS, how is this achieved? will affect the MCS but this is linked to GSM. For EGRPS
only we can play with TRXs, Ded TSL, EDAP, PCU, Gb

If a TRX is BLK-SYS when EGENA is

turned on, what is the most probably GTRX=Y and the TRX is not attached to the EDAP
cause?

Throughput, TBF est fail, TBF fail, TBF lost due to flush or
MS lost, GMSK share of EGPRS, TBF/TSL, Payload, EDAP
Name some EGPRS KPIs
congestion (mins/Gb), territory upgrade rejects, territory
downgrades, PCU congestion
What is PoC? Push-to-Talk over Cellular. It is a real-time service
What elements need to be added for
PoC Server, possible Presence server
PoC?
It is merely a transport layer, PoC is a service that uses
How is EGPRS used for PoC?
EGPRS
Are there re-transmission in PoC? Not from the PoC server. EGPRS uses normal algorithm
Start to Talk (STT) time, Voice Through Delay
What KPIs are used in PoC? (VTD),Glitches (delay in packet arrival), Lost data), Round
Trip Delay (RTT) (depends on user reaction)
What values are normally expected for
STT: <2s, VTD: <4s
STT and VTD?

What is the advantages/disadvantages Adv: greater possibility of the data being decoded for MSs in
of a low initial MCS bad quality. Dis: Less range if 8PSK due to power back-off

A small capacity cell with an antenna not more than 5m in

Define a Microcell
height
In a grid system, on the side of a building. Not on a corner
What is the best position for a microcell otherwise the canyon streets will propagate the signal too far.
antenna? In a non gird system, side or corner of the building wherever
best serves the target area.
Fast moving mobiles may select it and then leave the
What are the disadvantages of a micro
coverage area very fast. Local congestion because of high
cell?
traffic
 Use C2 penalty time to make the cell attractive only to slow
How can these be solved? mobiles. Run the cell as barred and use hierarchical handovers
to move the calls from the overlaying macros
Name some RF systems used in in- Active or passive Distributed Antenna Systems (DAS), leaky
building cells feeders, Yagis in the lift shaft.
If you don't know an answer to a NED, Jump, Quickplace, mailing lists, ETSI Specs, Nokia
question where do you look? Feature Descriptions, Training course material.
Why don't we suggest to have a bigger
More intracell Ho. Eat up PCU capacity
DEFAULT TERRITORY?
Diposkan oleh waveice di 23:21