Fault Code: 2215 - SPN: 94 - FMI: 18: ISX CM871

File: 680-t06-2215 Page 1 of 14
ISX CM871
Fault Code: 2215 | SPN: 94 | FMI: 18

Fuel Pump Delivery Pressure - Data Valid But Below Normal
Operating Range - Moderately Severe Level
1 Check for primary fault codes
2 Engine will not start
3 Damaged fuel supply lines
4 High fuel inlet restriction
5 Fuel shutoff valve is malfunctioning
6 Fuel lift pump is malfunctioning
7 Loose or damaged fuel line fittings
8 Fuel pump pressure regulator is malfunctioning
10 Fuel rail pressure sensor is malfunctioning
12 Fuel pump gear pump check
13 Pressure-side fuel filter is plugged
© 2008 Cummins Inc., Box 3005, Columbus, IN 47202-3005 U.S.A. Printed from QuickServe® Online.
All Rights Reserved. Last Modified: 07-Oct-2019
File: 680-t06-2215 Page 2 of 14
1 Check for primary fault codes

Solution: S00002474
Verification
Conditions
• Turn keyswitch ON.
• Connect the recommended Cummins® electronic service tool or equivalent.
Action
• Use the recommended Cummins® electronic service tool or equivalent to read the fault codes.
Specification
Before troubleshooting this fault code, troubleshoot any fault code that is active or has more than one inactive count
within the last 25 engine operating hours from the following list: 227,275, 329, 449, 1911, 2266, 2311
Linked Solutions
• None
Repair
• Perform a search on the appropriate fault codes.
Validation
• None
File: 680-t06-2215 Page 3 of 14
2 Engine will not start

Solution: S00000629
Verification
Conditions
Action
• Attempt to start the engine.
Specification
• If the engine starts, then proceed to the next Solution.
• If the engine will not start, then reset the search to crank no start.
Linked Solutions
• None
Repair
• Reset the search to crank no start.
Validation
• Connect all components
• Disable Fault Code
• Operate the engine within the "Conditions for Clearing the Fault Code" found in the Overview section of the
troubleshooting procedure.
• Verify that the fault code is no longer active.
• Check ECM Calibration Revision History
• Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision
number in the ECM.
• Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration
Revision History Database for applicable changes related to this fault code.
• Refer to ECM Calibration Revision History Database.
File: 680-t06-2215 Page 4 of 14
3 Damaged fuel supply lines

Solution: S00000447
Verification
Conditions
• Engine running.
Action
• Visually check fuel tank for adequate fuel supply.
• Visually inspect the engine fuel supply lines for signs of kinks, damage or fuel leaks.
• Visually inspect all fuel system gasket locations for signs of leakage.
Specification
• If the engine will not start, then reset the search to crank no start.
• If there is any damage or leaks found in the fuel system, then proceed to the Repair section.
Linked Solutions
• None
Repair
Repair or replace only the components that were found to be out of specification.
• Repair or replace the leaking components. Refer to Procedure 006-024
• Repair or replace damaged components.
• Repair or replace fuel gauge.
• Add fuel if needed.
Validation
number in the ECM.
File: 680-t06-2215 Page 5 of 14
4 High fuel inlet restriction

Solution: S00000515
Verification
Conditions
• Turn keyswitch OFF.
Action
• Measure the fuel inlet restriction. Refer to Procedure 006-020
Specification
• If the fuel gear pump inlet restriction is out of specification, then a malfunctioning low pressure fuel system
component has been detected.
Linked Solutions
• None
Repair
• Repair or replace the OEM fuel lines.
• Replace fuel filter.
• Repair or replace the fuel heater.
• Repair or replace the fuel tank stand pipe.
• Replace the fuel lift pump. Refer to Procedure 005-045
Validation
number in the ECM.
File: 680-t06-2215 Page 6 of 14

Solution: S00003449
Verification
Conditions
• Disconnect the fuel shutoff valve from the engine wiring harness.
Action
• Inspect the pins and connectors for damage. Refer to Procedure 019-361
• Inspect the fuel shutoff valve. Refer to Procedure 019-050
• Perform the voltage check for the fuel shutoff valve coil. Refer to Procedure 019-050
Specification
• If the fuel shutoff valve coil voltage does not meet specification, then a malfunctioning fuel shutoff valve has been
detected.
• If any damage is found, then proceed to the Repair section.
Linked Solutions
• None
Repair
• Replace the fuel shutoff valve. Refer to Procedure 019-050
Validation
number in the ECM.
File: 680-t06-2215 Page 7 of 14
6 Fuel lift pump is malfunctioning

Solution: S00003615
Verification
Conditions
Action
• Listen for fuel lift pump operation.
• Measure the lift pump pressure.
• Inspect the integrated fuel system module check valve.
Specification
• If the fuel lift pump pressure is not within specification, then a malfunctioning fuel lift pump has been detected.
Linked Solutions
• None
Repair
• Replace the electric fuel lift pump. Refer to Procedure 005-045
Validation
number in the ECM.
File: 680-t06-2215 Page 8 of 14
7 Loose or damaged fuel line fittings

Solution: S00000442
Verification
Conditions
• Verify adequate fuel level in the tank
Action
• Inspect for air being ingested into the fuel. Refer to Procedure 006-003
Specification
• If air is present in the fuel flow, then a damaged fuel supply line, loose or damaged fuel filter, or a loose
connection has been detected.
Linked Solutions
• None
Repair
• Tighten the loose fitting or replace the damaged component that allows air to enter the fuel system. Refer to
Procedure 006-003
Validation
• None
File: 680-t06-2215 Page 9 of 14

Solution: S00003630
Verification
Conditions
Action
• Remove the fuel pressure regulator. Refer to Procedure 005-073
• Visually inspect the fuel pressure regulator o-rings for damage.
Specification
Linked Solutions
• None
Repair
• Replace fuel pressure regulator. Refer to Procedure 005-073
Validation
number in the ECM.
File: 680-t06-2215 Page 10 of 14

Solution: S00003700
Verification
Conditions
Action
• Inspect the pins and connectors for damage. Refer to Procedure 019-361
• Remove the fuel shutoff valve. Refer to Procedure 005-043
• Inspect the fuel shutoff valve. Refer to Procedure 005-043
Specification
• If the fuel shutoff valve does not meet specification, then a malfunctioning fuel shutoff valve has been detected.
Linked Solutions
• None
Repair
• Replace the fuel shutoff valve. Refer to Procedure 005-043
Validation
number in the ECM.
File: 680-t06-2215 Page 11 of 14
10 Fuel rail pressure sensor is malfunctioning

Solution: S00003535
Verification
Conditions
Action
• Install a mechanical gauge on the engine.
• Use the recommended Cummins® electronic service tool or equivalent.
• Start the engine.
• Compare the sensor reading with the recommended Cummins® electronic service tool or equivalent to a
mechanical gauge.
Specification
• A malfunctioning fuel rail pressure sensor has been detected if the reading is not within the following
specification: 69 kPa [10 psi]
Linked Solutions
• None
Repair
• Replace the fuel pressure sensor. Refer to Procedure 019-115
Validation
• None
File: 680-t06-2215 Page 12 of 14

Solution: S00004440
Verification
Conditions
Action
• Remove the fuel pressure regulator. Refer to Procedure 005-073
• Visually inspect the fuel pressure regulator o-rings for damage.
Specification
Linked Solutions
• None
Repair
• Replace the fuel pump pressure regulator. Refer to Procedure 005-073
Validation
number in the ECM.
File: 680-t06-2215 Page 13 of 14
12 Fuel pump gear pump check

Solution: S00003691
Verification
Conditions
Action
• Perform the fuel pump gear pump pressure check. Refer to Procedure 005-016
• Perform the Fuel Pump Gear Pump Leak Test. Refer to Procedure 005-016
Specification
• If any of the checks are not within specification, then proceed to the Repair section.
Linked Solutions
• None
Repair
• Replace the fuel pump gear pump. Refer to Procedure 005-016
Validation
number in the ECM.
File: 680-t06-2215 Page 14 of 14
13 Pressure-side fuel filter is plugged

Solution: S00003539
Verification
Conditions
• Disconnect the electric fuel lift pump from the engine wiring harness.
• Engine running at idle.
Action
• Allow the engine to reach operating temperature.
• Run engine at high idle.
• Perform the Fuel Filter Restriction Test. Refer to Procedure 006-015
Specification
• If the differential pressure does not meet specification, then a plugged or blocked fuel filter has been detected.
Linked Solutions
• None
Repair
• Replace pressure side fuel filter. Refer to Procedure 006-015
Validation
number in the ECM.
If all steps have been completed and no root cause has been identified, then follow the technical
escalation process.

Fault Code: 2215 - SPN: 94 - FMI: 18: ISX CM871

Uploaded by

Copyright:

Available Formats

Fault Code: 2215 - SPN: 94 - FMI: 18: ISX CM871

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fault Code: 2215 - SPN: 94 - FMI: 18: ISX CM871

Uploaded by

Copyright:

Available Formats

File: 680-t06-2215 Page 1 of 14

Fault Code: 2215 | SPN: 94 | FMI: 18

1 Check for primary fault codes

2 Engine will not start

3 Damaged fuel supply lines

4 High fuel inlet restriction

5 Fuel shutoff valve is malfunctioning

6 Fuel lift pump is malfunctioning

7 Loose or damaged fuel line fittings

8 Fuel pump pressure regulator is malfunctioning

9 Fuel shutoff valve is malfunctioning

10 Fuel rail pressure sensor is malfunctioning

11 Fuel pump pressure regulator is malfunctioning

12 Fuel pump gear pump check

13 Pressure-side fuel filter is plugged

1 Check for primary fault codes

2 Engine will not start

3 Damaged fuel supply lines

4 High fuel inlet restriction

5 Fuel shutoff valve is malfunctioning

6 Fuel lift pump is malfunctioning

7 Loose or damaged fuel line fittings

8 Fuel pump pressure regulator is malfunctioning

9 Fuel shutoff valve is malfunctioning

10 Fuel rail pressure sensor is malfunctioning

11 Fuel pump pressure regulator is malfunctioning

12 Fuel pump gear pump check

13 Pressure-side fuel filter is plugged

You might also like