Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 22 views

    20ft Steel Pole Datasheet

    Uploaded by

    DVTech Engineering
    1. Install a 36" x 36" x 36" concrete foundation pad with reinforcement bars and anchor bolts protruding 2-3 inches. Pour and cure the concrete to a compressive strength of 3000 psi. 2. Insert wiring through the bottom of the steel pole and out the top. Slowly lift the pole into place on the pad, aligning the bolt holes. 3. Secure the pole to the pad using fasteners, washers, lock washers, and nuts on the anchor bolts. Adjust as needed using leveling nuts if conditions require.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    20ft Steel Pole Datasheet

    Uploaded by

    DVTech Engineering
    22 views3 pages
    1. Install a 36" x 36" x 36" concrete foundation pad with reinforcement bars and anchor bolts protruding 2-3 inches. Pour and cure the concrete to a compressive strength of 3000 psi. 2. Insert wiring through the bottom of the steel pole and out the top. Slowly lift the pole into place on the pad, aligning the bolt holes. 3. Secure the pole to the pad using fasteners, washers, lock washers, and nuts on the anchor bolts. Adjust as needed using leveling nuts if conditions require.

    Original Description:

    For CCTV

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. Install a 36" x 36" x 36" concrete foundation pad with reinforcement bars and anchor bolts protruding 2-3 inches. Pour and cure the concrete to a compressive strength of 3000 psi. 2. Insert wiring through the bottom of the steel pole and out the top. Slowly lift the pole into place on the pad, aligning the bolt holes. 3. Secure the pole to the pad using fasteners, washers, lock washers, and nuts on the anchor bolts. Adjust as needed using leveling nuts if conditions require.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    22 views3 pages

    20ft Steel Pole Datasheet

    Uploaded by

    DVTech Engineering
    1. Install a 36" x 36" x 36" concrete foundation pad with reinforcement bars and anchor bolts protruding 2-3 inches. Pour and cure the concrete to a compressive strength of 3000 psi. 2. Insert wiring through the bottom of the steel pole and out the top. Slowly lift the pole into place on the pad, aligning the bolt holes. 3. Secure the pole to the pad using fasteners, washers, lock washers, and nuts on the anchor bolts. Adjust as needed using leveling nuts if conditions require.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    FCI- POLE 20FT DATASHEET

    20ft Steel Pole Installation


    1. Select a suitable site for the Steel Pole and prepare the pad site using a hole 36" x 36" x
    36" deep. The top of the concrete foundation should be flush with the ground.
    2. Be sure that there are no underground electric or phone cables, gas or water lines in the
    area where the pole will be located.
    Special attention must be paid to the size of the wiring conduit and its location within the
    concrete foundation and jig. The Wiring Conduit can be up to 2" in diameter. Use reducers if
    necessary. Also, make sure that the Wiring Conduit is in the center of the foundation and
    Anchor Jig during installation.
    3. To help reinforce the concrete foundation, place (12) 1/2” diameter x 32” long
    Reinforcement Bars (”rebar”). Use suitable preparation methods to place the rebar.
    4. FOR ANCHOR BOLT INSTALLATIONS:
    Pour concrete per directions on the dimensions of the bolt pattern and suspend
    appropriate bolts in the concrete around the wiring conduit. Leave 2” to 3” of the BOLTS
    protruding above the pad. If you are using leveling nuts, leave 4” to 6” protruding.
    Prepare the concrete per manufacturer's directions. The concrete must have a
    compressive strength of 3000 psi, and must be fabricated following ACI318-89
    requirements. Allow the concrete foundation to cure thoroughly before proceeding with the
    installation.
    Be sure that the pole is oriented properly, with the carriage
    5. Place the pole on the pad with the holes on the Base Plate aligned with the bolts of the
    anchor bolts or anchor jig
    6. Remove the access opening plates at the bottom and top.
    7. Insert the wiring into the 3" diameter hole in the base of the pole up, into and out of the
    bottom access opening. Make sure all slack is pulled completely through.
    8. Insert connecting wiring into the bottom access opening, run through the pole up to the
    top access opening. Insert the end through the housing connecting hole. Close the top
    access opening and make necessary wiring connections at the bottom access opening
    9. Slowly lift the pole into the upright position, aligning the holes of the Base Plate with the
    Bolts in the concrete pad
    10. Secure the pole to the pad with fasteners
    11. Thread two (2) nuts onto each of the (4) bolts). The end with 6" of clearance will be the
    top of the Anchor Jig, the end with 1 1/2" clearance will be the bottom.
    Because of surface conditions it may be necessary to use leveling nuts. See step 5 below
    for information.
    12. Place the short end of each Bolt into the outside holes of the Cross Strap. Place Hex
    Nuts onto each Bolt and finger tighten
    13. Turn the Anchor Jig over and place Single Straps over the Bolts.Use the inside hole of
    each strap. Place Hex Nuts onto each Bolt and finger tighten.

    14. Before using the Anchor Jig verify that the center to center dimensions between the bolts
    are even. If not, adjust accordingly. Firmly tighten all Hex Nuts.
    15. Standard installation without leveling nuts.
    16. If, due to conditions or other requirements, leveling nuts are needed, adjustments will
    have to be made to the Anchor Jig. Leveling nuts and washers are NOT provided with the
    pole.
    17. The Flat Washers, Lock Washers, and remaining Hex Nuts will be used to fasten the
    pole to the Anchor Jig.

    You might also like