Defogger: Section
Defogger: Section
E
CONTENTS
BASIC INSPECTION .................................... 3 Component Inspection .............................................12 F
WORK FLOW
C
DEF
M
AWJIA0001GB
DETAILED FLOW
N
1. CUSTOMER INFORMATION
Talk to the customer to obtain detailed information about the symptom. O
>> GO TO 2
2. PRELIMINARY CHECK P
>> GO TO 3
3. SYMPTOM
Check for symptoms. Refer to XXX.
>> GO TO 4
4. MALFUNCTIONING PARTS
Repair or replace the applicable parts.
>> GO TO 5
5. SYSTEM CHECK
Operate rear window defogger switch to ensure that rear window defogger and heated mirrors operate.
Does the system operate normally?
YES >> INSPECTION END
NO >> Refer to GI Intermittent Incident.
ALLIA0313GB
H
System Description INFOID:0000000001527585
Operation Description
• Turn rear window defogger switch ON when the ignition switch is turned ON. Then A/C and AV switch I
assembly (rear window defogger switch) transmits rear window defogger switch signal to BCM.
• BCM transmits rear window defogger control signal to IPDM E/R and display unit via CAN communication
when rear window defogger operates. J
• IPDM E/R turns rear window defogger relay and heated mirror relay ON when rear window defogger switch
signal is received.
• Rear window defogger and door mirror defogger are supplied with power and operate when rear window
K
defogger relay and heated mirror relay turn ON.
• Rear window defogger ON is displayed when signal is received.
Timer function DEF
• BCM turns rear window defogger relay and heated mirror relay ON for approximately 15 minutes when rear
window defogger switch is turned ON while ignition switch is ON. It makes rear window defogger and door
mirror defogger operate.
• Timer is canceled after pressing rear window defogger switch again during timer operation. Then BCM turns M
rear window defogger relay and heated mirror relay OFF. The same reaction also occurs during timer opera-
tion, if the ignition switch is turned OFF.
N
INPUT/OUTPUT SIGNAL CHART
ALLIA0314ZZ
1. A. Steering column assembly 2. A/C and AV switch assembly (rear 3. A. Rear window defogger ground
B. BCM M18, M20 (view with instru- window defogger switch) M98 connector D604
ment panel removed) B. Rear window defogger connector
D406
4. IPDM E/R E120, E122, E124 5. Door mirror (door mirror defogger)
LH D4, RH D107
• Operates the rear window defogger with the operation of rear window defogger switch.
BCM
• Performs the timer control of rear window defogger.
• Operates the rear window defogger and the door mirror defogger with the control signal from
Rear window defogger relay
BCM.
A/C and AV switch assembly • The rear window defogger switch is turned ON.
(rear window defogger switch) • Turns the indicator lamp ON when detecting the operation of rear window defogger.
• Heats the heating wire with the power supply from the rear window defogger relay to prevent
Rear window defogger
the rear window from fogging up.
• Heats the heating wire with the power supply from the heated mirror relay to prevent the door
Door mirror defogger
mirror from fogging up.
SYSTEM APPLICATION
BCM can perform the following functions for each system. G
NOTE:
It can perform the diagnosis modes except the following for all subsystem selection items.
H
Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
Rear window defogger REAR DEFOGGER × × I
BCM BCM ×
K
Data monitor
1.CHECK FUSES
Check if any of the following fuses in the IPDM E/R are blown.
Terminals
Condition of rear
(+) Voltage (V)
window defogger
(–) (Approx.)
IPDM E/R con- switch
Terminal
nector
ON Battery voltage
E124 60 Ground
OFF 0
LIIA2190E
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation of IPDM E/R".
NO >> GO TO 3
3. CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to GI-39, "Intermittent Incident"
Is the inspection result normal?
YES >> Check the following.
• Battery power supply circuit.
• IPDM E/R.
NO >> Repair or replace the malfunctioning parts.
Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window B
from fogging up.
Component Function Check INFOID:0000000001527599
1. CHECK FILAMENT
Check the filament for damage or open circuits.
Refer to DEF-38, "Inspection and Repair".
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair filament. Refer to DEF-38, "Inspection and Repair".
LIIA0970E
WIIA0528E
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror B
from fogging up.
Component Function Check INFOID:0000000001546704
C
1. CHECK DOOR MIRROR DEFOGGER LH
Check that heating wire of door mirror defogger LH is heated when turning the rear window defogger switch
ON. D
Is the inspection result normal?
YES >> Door mirror defogger is OK.
NO >> Refer to DEF-15, "Diagnosis Procedure". E
F
1. CHECK POWER SUPPLY
Check if the following fuse in the IPDM E/R is blown.
G
COMPONENT PARTS AMPERE FUSE NO.
IPDM E/R 15A 43
Is the inspection result normal? H
YES >> GO TO 2
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
2. CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT I
LIIA1454E
WIIA0531E
LIIA0970E
WIIA0528E
LIIA1454E
WIIA0531E
DEF
ALLWA0056GB
DEF
ALLWA0057GB
ALLIA0288GB
DEF
ALLIA0289GB
ALLIA0290GB
DEF
ALLIA0291GB
ALLIA0292GB
DEF
ALLIA0293GB
ALLIA0294GB
DEF
DEF
DEF
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING: E
• To avoid rendering the SR inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
H
DEF
INSPECTION
1. When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.
SEL122R
SEL263
SEL265
REPAIR
REPAIR EQUIPMENT
• Conductive silver composition (Dupont No. 4817 or equivalent)
PIIA0215E
F
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited. G
Do not touch repaired area while test is being conducted.
I
SEL012D
M
SEL013D